Cable Assemblies - Accu-Tech

Cable Assemblies - Accu-Tech
|
TRAINING
|
SPLICE EQUIPMENT
|
TEST EQUIPMENT
|
SPLICE CLOSURES
Corning Cable Systems offers the most complete
line of connectors and factory-terminated cables, from
single-fiber jumpers to high-fiber-count assemblies.
As the industry’s leading supplier of cable assemblies,
Corning Cable Systems’ state-of-the-art manufacturing
process ensures unsurpassed connector performance
with products that meet or exceed all industry standards
for reflectance and insertion loss. Highly trained and
qualified associates thoroughly screen the incoming
fibers and ferrules, assemble and polish them in a
carefully monitored and controlled process, and quality
test the assemblies at the end. This assembly and
polishing process ensures the same outstanding
quality in every connector.
A LANscape ®
Solutions Product
|
Corning Cable Systems' standard 50 µm and Pretium®
300 Solutions OM3 jumpers feature enhanced bend
performance enabled by Corning® ClearCurve®
multimode fiber.
| Photo CCA29
SPECIFICATION SHEET LAN-525-EN | PAGE 1
SC Ultra PC Cable Assembly | Photo CCA31
|
ST® Compatible Ultra PC Cable Assembly, 12-Fiber
PRETERMINATED SYSTEMS
|
CABLES
|
CONNECTORS
|
CABLE ASSEMBLIES
|
LC Duplex Cable Assembly, 2-FIber | Photo LAN663
HARDWARE
Cable Assemblies
Cable Assemblies
Single-Mode Connector Types
SC Ultra PC
SC Angled PC
LC Ultra PC
SC Angled PC | Drawing ZA-1451
LC Angled PC
FC Ultra PC
FC Angled PC
ST® Compatible Ultra PC
MT-RJ
Note: Drawings are not to scale.
SPECIFICATION SHEET LAN-525-EN | PAGE 2
A LANscape ®
Solutions Product
Jacketed Fiber
900 µm Fiber
Drawing ZA-1447
Drawing ZA-1448
Drawing ZA-1451
Drawing ZA-1452
Drawing ZA-3135
Drawing ZA-3135
Drawing ZA-2958
Drawing ZA-3136
Drawing ZA-1441
Drawing ZA-1442
Drawing ZA-1445
Drawing ZA-1446
Drawing ZA-1457
Drawing ZA-1458
Drawing ZA-2385
Drawing ZA-2385
SC Angled PC | Drawing ZA-1451
MT-RJ
Drawing ZA-2832
Drawing ZA-2831
Drawing ZA-2831
SPLICE EQUIPMENT
Drawing ZA-2838
|
Drawing ZA-2836
TEST EQUIPMENT
Drawing ZA-2836
|
Drawing ZA-2837
|
SPECIFICATION SHEET LAN-525-EN | PAGE 3
PRETERMINATED SYSTEMS
|
CABLES
|
CONNECTORS
|
CABLE ASSEMBLIES
|
Note: Drawings are not to scale.
Drawing ZA-2835
SPLICE CLOSURES
ST® Compatible PC
900 µm Fiber
|
LC PC
Jacketed Fiber
HARDWARE
SC PC
|
Multimode Connector Types
|
A LANscape ®
Solutions Product
TRAINING
Cable Assemblies
Cable Assemblies
A LANscape ®
Solutions Product
Connector Performance
Controlling connector end-face geometry is key to ensuring network reliability. Radius of curvature, apex offset and
fiber undercut are the three critical parameters that affect long-term connector performance. These parameters are
closely monitored and controlled throughout Corning Cable Systems’ automated process, thus assuring the highest
quality in each and every connector assembly.
Radius of Curvature
Radius of curvature describes the radius of the end-face surface
measured from the ferrule axis. The correct radius of curvature is
necessary to control the compressive forces on the connector
end-face. Radius of curvature values between 10 to 30 mm are
recommended to avoid fiber damage and to ensure low reflectance
and insertion loss.
End-Face Curvature
Ferrule
Fiber
Radius
Radius of Curvature | Drawing ZA-3450
Apex Offset
Apex offset is the displacement between the apex of the sphere that
fits the ferrule end-face and the center of the fiber core. Excessive
apex offset can lead to lack of physical contact of the fiber cores
and an increase in insertion loss. A typical apex offset value
of 50 µm is recommended. Values greater than 50 µm can
reduce fiber-to-fiber contact and cause increases in reflectance
over the operating temperature.
Fiber Undercut/Protrusion
Fiber undercut is the distance of the fiber above or below the fitted
spherical surface of the ferrule. Proper undercut guarantees that
fiber-to-fiber contact will always be maintained over the operating
temperature range. An undercut value of ± 50 nanometers is
F
recommended to avoid air gaps between fibers. Larger undercut
values can cause changes in reflectance and insertion loss.
Excessive fiber protrusion can increase the compressive load
at the end of the fiber causing fiber damage or failure of the
fiber-ferrule epoxy bond.
SPECIFICATION SHEET LAN-525-EN | PAGE 4
Top of Dome
Apex Offset
Ferrule
Fiber
Apex Offset | Drawing ZA-3451
Undercut
Ferrule
Fiber
Fiber Undercut/Protrusion
| Drawing ZA-3452
|
Single-Fiber Cable
|
A LANscape ®
Solutions Product
TRAINING
Cable Assemblies
TEST EQUIPMENT
|
SPLICE EQUIPMENT
Example shows cable with an LC PC connector installed.
Single-Fiber Cable | Drawing ZA-3414
Note: Available in 1.6 mm, 2.0 mm or 2.9 mm outer diameters.
|
Zipcord Cable (2 fibers)
|
10 in (+1.5 in/-0 in)
HARDWARE
|
SPLICE CLOSURES
Example shows cable with LC PC connectors installed.
CABLE ASSEMBLIES
Zipcord Cable (2 fibers) | Drawing ZA-3415
Note: Available in 1.6 mm, 2.0 mm and 2.9 mm subunits.
DFX® Cable (2 fibers)
CONNECTORS
|
Example shows cable with SC ultra PC connectors installed.
PRETERMINATED SYSTEMS
|
10 in (+3 in/-0 in)
CABLES
|
1
DFX Cable (2 fibers) | Drawing ZA-3416
Notes:
1) Available in 2.0 mm or 2.9 mm legs.
2) For total assembly length less than 3 ft, legs are 6 in (+3 in/-0 in).
|
SPECIFICATION SHEET LAN-525-EN | PAGE 5
1
Cable Assemblies
A LANscape ®
Solutions Product
Fan-Out Cable (2-24 fibers)
Example shows cable with SC PC connectors installed.
39 in (+3 in/-0 in) Legs
Fan-Out Cable (2-24 fibers) | Drawing ZA-3417
Note:
1) Maximum fiber count for fan-out cable assemblies is 24 fibers.
2) Available in 1.6 mm, 2.0 mm and 2.9 mm subunits.
MIC® Cable Furcation (2-12 fibers) with 2.9 mm Legs
Example shows cable with SC PC connectors installed.
Heat-Shrink Furcation
3
39 in (+3 in/-0 in) 2.9 mm Legs
MIC Cable Furcation (2-12 fibers) | Drawing ZA-3418
Note: Available in 2.0 mm and 900 µm legs.
MIC Cable Furcation (13-24 fibers) with 900 µm Legs
Example shows cable with ST® Compatible PC Connectors3installed.
SIECOR
39 in (+3 in/-0 in) 900 µm Legs
MIC Cable Furcation (13-24 fibers) | Drawing ZA-3419
Notes:
1) Also available in 2.0 mm and 2.9 mm legs.
2) Standard construction of 24-fiber assembly is a single-layer MIC Cable.
3) For MIC Unitized Cable construction, a serialized part number is required.
SPECIFICATION SHEET LAN-525-EN | PAGE 6
|
MIC® Unitized Cable Furcation (36-144 fibers)
|
A LANscape ®
Solutions Product
TRAINING
Cable Assemblies
Note:
1) Also available in 2.0 mm and 2.9 mm legs.
2) Standard construction is 6-fiber subunit up to 48-fiber, and 12-fiber subunit from 60 to 144 fibers.
3) 24-fiber assembly available in MIC Unitized Cable construction. A serialized part number is required.
Ribbon Riser and FREEDM® Ribbon Cable Configuration (12-72 fibers)
Fan-Out Body
900 µm Legs
25 in (+3 in/-0 in) Standard
Ribbon Riser and FREEDM Ribbon Cable Configuration | Drawing ZA-3140
Ribbon Riser and FREEDM Ribbon Cable Configuration (84-216 fibers)
CONNECTORS
Example shows 216-fiber cable with SC ultra PC connectors installed.
Exposed Ribbon
35 in Standard
#2 - 16 in std.
Fan-Out Body
Ribbon Riser and FREEDM Ribbon Cable Configuration | Drawing ZA-2960
Fiber Counts for Protective Tubes:
Tube #1: 1-72 fibers
Tube #2: 73-144 fibers
Tube #3: 145-216 fibers
SPECIFICATION SHEET LAN-525-EN | PAGE 7
E
900 µm Legs
25 in (+3 in/-0 in) Standard
|
Teflon Protective Tubes
PRETERMINATED SYSTEMS
®
Epoxy Plug
CABLES
|
#3 - 23 in std.
|
#1 - 8 in std.
|
43 in Total Length
Heat-Shrink
CABLE ASSEMBLIES
Exposed Ribbon
35 in Standard
|
Spiral Wrap: 8 in Standard
HARDWARE
|
Example shows cable with SC ultra PC connectors installed.
|
MIC Unitized Cable Furcation (36-144 fibers) | Drawing ZA-3420
SPLICE CLOSURES
39 in (+3 in/-0 in) 900 µm Legs
8 in
TEST EQUIPMENT
|
SPLICE EQUIPMENT
Example shows cable with SC PC connectors installed.
Cable Assemblies
A LANscape ®
Solutions Product
ALTOS® Riser Cable Configuration
Example shows cable with SC PC connectors installed.
Heat-Shrink
8 in
Standard Buffer Tube Length
Fan-Out Body
900 µm Legs
25 in (+3 in/-0 in) Standard
ALTOS Riser Cable Configuration | Drawing ZA-3421
ALTOS Outside Plant and FREEDM® Cable Configuration
Example shows cable with SC PC connectors installed.
8 in
Heat-Shrink
Standard Buffer Tube Length
Fan-Out Body
9
900 µm Legs
25 in (+3 in/-0 in) Standard
ALTOS Outside Plant and FREEDM Cable Configuration | Drawing ZA-2956
9
SPECIFICATION SHEET LAN-525-EN | PAGE 8
Type
58
72
02
04
12
54
61
44
22
23
21
98
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.15
0.3
0.15
0.15
0.3
|
SPLICE CLOSURES
Reflectance (dB)
Typical
≤ -58
≤ -59
≤ -58
≤ -58
≤ -58
≤ -59
≤ -58
≤ -75
≤ -75
≤ -58
≤ -75
≤ -53
|
Typical Insertion
Loss (dB)
Ferrule
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Composite
Housing
Composite
Composite
Composite
Composite
Composite
Nickel, Brass
Composite
Composite
Composite
Composite
Nickel, Brass
Composite
|
SPECIFICATION SHEET LAN-525-EN | PAGE 9
PRETERMINATED SYSTEMS
|
CABLES
|
SC Simplex UPC
SC Duplex UPC
LC Simplex UPC
LC Duplex UPC
LC 90º Boot Clip UPC
FC Simplex UPC
ST Compatible UPC
SC Simplex APC
LC Simplex APC
LC Duplex with 90º Boot Clip
FC Simplex APC
MT-RJ (non-pinned)
Code
HARDWARE
Single-Mode Connectors
Composite
Composite
Composite
Composite
Composite
Composite
Composite
|
Notes:
1) Low-loss cable assemblies available for use with all Plug & Play™ Systems.
2) Refer to LAN-664-EN for ordering information.
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Composite
TEST EQUIPMENT
0.35
0.35
0.35
0.35
0.35
0.35
0.3
Housing
|
39
57
50
03
05
17
97
Ferrule
CABLE ASSEMBLIES
SC PC Simplex
SC PC Duplex
ST® Compatible PC
LC PC Simplex
LC PC Duplex
FC PC Simplex
MT-RJ (non-pinned)
Code
|
Type
Typical Insertion Loss (dB)
50/125 µm and
62.5/125 µm
CONNECTORS
Multimode Connectors
SPLICE EQUIPMENT
|
specifications |
|
A LANscape ®
Solutions Product
TRAINING
Cable Assemblies
Cable Assemblies
A LANscape ®
Solutions Product
ordering information |
Single-Fiber Connectors
Corning Cable Systems patch cords and high-fiber-count assemblies are ordered using five easy steps. The steps involve the
selection of connector(s), cable and length. The format and steps are listed below.
■■■■
|1
|1
■■
|2
Select connector code.
00 = No connectors (use
when ordering a pigtail)
Multimode
39 = SC PC simplex
57 = SC PC duplex
03 = LC PC simplex*
05 = LC PC duplex*
17 = FC PC simplex
50 = ST® Compatible PC
Single-mode
58 = SC simplex UPC
44 = SC simplex APC
72 = SC duplex UPC
02 = LC simplex UPC*
22 = LC simplex APC*
04 = LC duplex UPC*
12 = LC 90º boot clip UPC*
54 = FC simplex UPC
21 = FC simplex APC
61 = ST Compatible UPC
|2
■■■■■
|3
Select fiber count.
01-96
See Note 3.
|3
Select cable code
based on construction
and fiber type
(see Table A).
See Notes 1 and 2.
SPECIFICATION SHEET LAN-525-EN | PAGE 10
■■■
|4
|4
■
|5
Select cable assembly
length.
001 to 999
See Note 4.
|5
Select unit of measure.
M = Meters
F = Feet
Notes:
1) Connector code based on
type of adapter used at the
patch panel and the electronic
interface. Always use the lowest
code first when constructing the
part number.
2) *Available on 1.6 mm, 2.0 mm
and 900 µm cable types only.
3) For fiber counts greater than
96, contact a Corning Cable
Systems Customer Service
Representative.
4) For lengths greater than 999,
contact a Corning Cable Systems
Customer Service Representative.
Table A
T4180
R4131
G4131
K3141
K2141
K3116
B3131
B2131
B3116
T3180
T2180
T3116
R3131
R2131
R3116
G3131
G2131
G3116
B61HD
B61LD
B61XD
T61HD
T61LD
T61XD
R61HD
R61LD
R61XD
K8120
K8130
B8120
B8131
T8120
T8180
R8120
R8131
KJ140*
KC725*
KW725*
BJ131*
BC725*
BW725*
TJ180*
TC725*
TW725*
RJ131*
RC725*
RW725*
K8130
K8120
B8131
B8120
B81NF
B8131
B8120
T8180
T8120
T81NF
T8180
T8120
*Defines standard as 25-in leg lengths. Other leg lengths available. Part number will change.
R9131
R9120
R8131
R8120
R81NF
R8131
R8120
G9131
G9120
|
|
SPECIFICATION SHEET LAN-525-EN | PAGE 11
PRETERMINATED SYSTEMS
|
Note: Please contact Customer Service for Pretium 550 and Pretium 600 Solutions cable assembly part numbers.
G5131
G5120
G5116
TEST EQUIPMENT
|
K61HD
K61LD
K61XD
K8130
K8120
K81NF
R5131
R5120
R5116
SPLICE CLOSURES
T5180
T5120
T5116
|
B5131
B5120
B5116
HARDWARE
K5141
K5120
K5116
|
Single-Fiber Cable
2.9 mm
2.0 mm
1.6 mm
Zipcord Cable (2 fiber)
2.9 mm
2.0 mm
1.6 mm
DFX® Cable (2 fiber)
2.9 mm legs
2.0 mm legs
Fan-Out Cable (2-24 fibers)
2.9 mm subunits
2.0 mm subunits
1.6 mm subunits
MIC ® Cable (2-12 fibers)
2.9 mm
2.0 mm
900 µm
MIC Cable (> 12 fibers)
2.0 mm legs
900 µm legs
MIC Unitized Cable (36-144 fibers)
900 µm legs
2.0 mm legs
Ribbon Interconnect Riser
(2, 4 and 12 fiber)
Ribbon Riser
ALTOS® Riser Cable
B4131
CABLE ASSEMBLIES
Cable Listing: Riser – OFNR
K4141
Bend-Improved
Single-Mode
|
900 µm
Single-Mode
CONNECTORS
Cable Listing: No Listing Required
50 µm
|
Cable Type
62.5 µm
CABLES
Fiber Type
LANscape®
Pretium® 300
Solutions
SPLICE EQUIPMENT
|
ordering information | (continued)
|
A LANscape ®
Solutions Product
TRAINING
Cable Assemblies
Cable Assemblies
A LANscape ®
Solutions Product
ordering information | (continued)
Table A (continued)
Fiber Type
Cable Type
Cable Listing: Plenum – OFNP
Single-Fiber Cable
2.9 mm
2.0 mm
1.6 mm
Zipcord Cable (2 fiber)
2.9 mm
Fan-Out Cable
2.9 mm subunits
2.0 mm subunits
1.6 mm subunits
MIC® Cable (2-12 fibers)
2.9 mm
2.0 mm
900 µm legs
MIC Cable (> 12 fibers)
2.0 mm legs
MIC Unitized Cable (36 - 144 fibers)
900 um legs
2.0 mm legs
Ribbon Interconnect (2, 4 and 12 fiber)
Ribbon Plenum
Indoor/Outdoor
FREEDM® Cable
FREEDM LST ™ Cable
FREEDM Ribbon Riser Cable
FREEDM One Riser Cable (6 and 12 fiber)
2.9 mm, 39 in legs
2.0 mm, 39 in legs
900 µm, 39 in legs
FREEDM One Plenum Cable (6 and 12 fiber)
2.9 mm, 39 in legs
2.0 mm, 39 in legs
900 µm, 39 in legs
Outdoor
ALTOS® Cable
Tactical Cable
2.0 mm legs
62.5 µm
50 µm
LANscape®
Pretium® 300
Solutions
K3841
K2841
K3816
B3831
B2831
B3816
T3880
T2880
T3816
R3831
R2831
R3816
G3831
G2831
G3816
K68HD
K68LD
K68XD
B68HD
B68LD
B68XD
T68HD
T68LD
T68XD
R68HD
R68LD
R68XD
G68HD
G68LD
G68XD
K5841
B5831
T5880
Single-Mode
Bend-Improved
Single-Mode
R5831
K8830
K8820
K88NF
K8830
K8820
B8831
B8820
B88NF
B8831
B8820
T8880
T8820
T88NF
T8880
T8820
KWF25*
KSF25*
KCF25*
BWF25*
BSF25*
BCF25*
TWF25*
TSF25*
TCF25*
RWF25*
RSF25*
RCF25*
K8P30
K8P20
K8PNF
B8P31
B8P20
B8PNF
T8P80
T8P20
T8PNF
R8P31
R8P20
R8PNF
KW425*
BW425*
TW425*
RW425*
K8830
K8820
KJ840*
KC825*
K8F30
K8F20
K8FNF
K8U20
B8831
B8820
BJ831*
BC825*
B8F31
B8F20
B8FNF
T8880
T8820
TJ880*
TC825*
T8F80
T8F20
T8FNF
*Defines standard as 25-in leg lengths. Other leg lengths available. Part number will change.
R8831
R8820
R88NF
R8831
R8820
R8831
R8820
RJ831*
RC825*
G5831
G8831
G8820
G88NF
G8831
G8820
G8831
G8820
GJ831*
GC825*
R8F31
R8F20
R8FNF
H8U20
Notes:
1) Please contact Customer Service for Pretium 550 and Pretium 600 Solutions cable assembly part numbers.
2) When using the standard part number scheme, 39-in leg lengths are standard. Otherwise, a serialized part number will be required.
SPECIFICATION SHEET LAN-525-EN | PAGE 12
MT-RJ Jumpers
Corning Cable Systems 2-fiber patch cords are ordered using four easy steps. The steps involve the selection of connector(s),
cable and length. The format and steps are listed below.
See Notes 1-3.
3) *LC available with 2.0 mm legs
only. If 900 µm or 1.6 mm legs
are required, please contact
Customer Service.
See Note 4.
|4
Select unit of measure.
M = Meters
F = Feet
62.5 µm
50 µm
LANscape®
Pretium® 300
Solutions
Ribbon Interconnect
02KJ140
02BJ131
02TJ180
02RJ131
Ribbon Interconnect
02KJ840
02BJ831
02TJ880
02RJ831
Cable Type
Cable Listing: Riser – OFNR
Cable Listing: Riser – OFNP
Single-Mode
Notes:
1) For hybrid jumpers, standard leg length for single-fiber connector end is 10 in, 2.9 mm legs. For LC, standard leg is 2.0 mm.
2) Please contact Customer Service for Pretium 550 and Pretium 600 Solutions cable assembly part numbers.
SPECIFICATION SHEET LAN-525-EN | PAGE 13
|
|
Fiber Type
CONNECTORS
|
Table B
4) For lengths greater than 999,
contact a Corning Cable Systems
Customer Service Representative.
TEST EQUIPMENT
|
001 – 999
SPLICE CLOSURES
Select length.
|
|3
2) MT-RJ patch cords are
typically sold without pins.
For pinned versions, call
Customer Service.
HARDWARE
Select cable code
based on construction
and fiber type
(see Table B).
|
For hybrid MT-RJ jumpers,
use the following options to
construct the part number:
Multimode
39 = SC PC simplex
57 = SC PC duplex
03 = LC PC simplex*
05 = LC PC duplex*
17 = FC PC simplex
50 = ST® Compatible PC
Single-mode
58 = SC simplex UPC
72 = SC duplex UPC
02 = LC simplex UPC*
04 = LC duplex UPC*
12 = LC 90º boot clip UPC*
54 = FC simplex UPC
61 = ST Compatible UPC
Notes:
1) Connector code based on
type of adapter used at the
patch panel and the electronic
interface. Always use the lowest
code first when constructing the
part number.
CABLES
00 = No connectors (use
when ordering a pigtail)
Multimode
97 = MT-RJ (non-pinned)
Single-mode
98 = MT-RJ (non-pinned)
|2
|4
|
Select connector code.
|3
■
CABLE ASSEMBLIES
|2
■■■
PRETERMINATED SYSTEMS
|1
|1
■■■■■■■
|
■■■■
SPLICE EQUIPMENT
|
ordering information | (continued)
|
A LANscape ®
Solutions Product
TRAINING
Cable Assemblies
Cable Assemblies
A LANscape ®
Solutions Product
ordering information | (continued)
MT-RJ Trunks, 2-144 Fibers
■■
|1
|1
■■
|2
Select connector
type on first end.
Single-mode
87 = MT-RJ (pinned)
See Note 1.
Multimode
86 = MT-RJ (pinned)
See Notes 2 and 3.
For single-fiber connectors,
use the following options to
construct the part number:
Multimode
39 = SC PC simplex
57 = SC PC duplex
03 = LC PC simplex*
05 = LC PC duplex*
17 = FC PC simplex
50 = ST® Compatible PC
Single-mode
58 = SC simplex UPC
72 = SC duplex UPC
02 = LC simplex UPC*
04 = LC duplex UPC*
54 = FC simplex UPC
61 = ST Compatible UPC
See Note 4.
■■
|3
■
|4
|2
■■
|5
Select connector
type on second end.
Single-mode
87 = MT-RJ (pinned)
Multimode
86 = MT-RJ (pinned)
See Notes 3 and 5.
|3
Select standard
fiber count.
02 =
06 =
12 =
24 =
36 =
48 =
72 =
96 =
E4 =
|4
2 fibers
6 fibers
12 fibers
24 fibers
36 fibers
48 fibers
72 fibers
96 fibers
144 fibers
Select fiber type.
R=
K=
B=
T=
Single-mode
62.5 µm multimode
50 µm multimode
50 µm laser-optimized
multimode
H = Bend-improved
single-mode
SPECIFICATION SHEET LAN-525-EN | PAGE 14
■■
|6
■■■
|7
|5
■
|8
Select cable type.
81 = MIC® Riser Cable
88 = MIC Plenum Cable
|6
Select cable
performance.
31
30
31
80
|7
=
=
=
=
Single-mode
62.5 µm multimode
50 µm multimode
50 µm laser-optimized
multimode
Select assembly length.
001 – 999
See Note 6.
|8
Select unit of measure.
M = Meters
F = Feet
Notes:
1) Select connector code based
on type of adapter used at the
patch panel and the electronic
interface. Always use the lowest
code first when constructing the
part number.
2) Most multi-fiber applications
are for backbone cabling and
will require an MT-RJ (pinned)
connector. If non-pinned
connectors are required, please
contact Customer Service.
3) For MT-RJ end, standard legs
are 900 µm. Leg lengths are
39 in (-0 / +3 in).
4) For fiber counts of 12 or less,
standard legs are 2.9 mm, leg
lengths 39 in (-0 / +3 in). For
fiber counts greater than 12,
standard legs are 900 µm, leg
lengths 39 in (-0 / +3 in).
5) If non-pinned connectors
are required, please contact
Customer Service.
6) For lengths greater than 999,
contact a Corning Cable Systems
Customer Service Representative.
7) LCs are only available on
900 mm, 1.6 mm and 2.0 mm.
8) Contact Customer Service for
Pretium 550 and Pretium 600
Solutions cable assembly part
numbers.
|4
|5
03 = LC PC simplex - 1st end; 39 = SC PC simplex - 2nd end
01 = 1-fiber cable
T2180 = 50 µm laser-optimized multimode, 2.0 mm riser rate
010 = Assembly length of 10
F = Unit of measure in feet
Jumper with MT-RJ Connectors
50 µm laser-optimized multimode jumper with SC PC duplex and MT-RJ (non-pinned) connectors on
2-fiber ribbon interconnect riser cable, 25 m
57 97 02TJ180 025 M
=
=
=
=
|2
|3
|4
57 = SC PC duplex - 1st end; 97 = MT-RJ (non-pinned) - 2nd end
02T2180 = 50 µm laser-optimized multimode, ribbon interconnect riser cable
025 = Assembly length of 25
M = Unit of measure in meters
|
|
SPECIFICATION SHEET LAN-525-EN | PAGE 15
PRETERMINATED SYSTEMS
|
CABLES
|
CONNECTORS
|
1
2
3
4
|1
TEST EQUIPMENT
|3
|
=
=
=
=
=
|2
SPLICE CLOSURES
1
2
3
4
5
|1
|
03 39 01 T2180 010 F
HARDWARE
50 µm laser-optimized multimode jumper with LC PC simplex and SC PC simplex connectors on
2.0 mm riser single-fiber cable, 10 ft
|
Jumper with Single-Fiber Connectors
CABLE ASSEMBLIES
Part Number Examples
SPLICE EQUIPMENT
|
ordering information | (continued)
|
A LANscape ®
Solutions Product
TRAINING
Cable Assemblies
Cable Assemblies
notes |
Corning Cable Systems LLC • PO Box 489 • Hickory, NC 28603-0489 USA
800-743-2675 • FAX: 828-901-5973 • International: +1-828-901-5000 • www.corning.com/cablesystems
A LANscape ®
Solutions Product
Corning Cable Systems reserves the right to improve, enhance, and modify the features and specifications of Corning Cable Systems products without prior notification. ALTOS, DFX,
FREEDM, LANscape, MIC and Pretium are registered trademarks of Corning Cable Systems Brands, Inc. Plug & Play is a trademark of Corning Cable Systems Brands, Inc. ClearCurve and
Corning are registered trademarks of Corning Incorporated. LST is a trademark of Corning Cable Systems LLC. ST is a registered trademark of Lucent Technologies. All other trademarks are
the properties of their respective owners. ©2008, 2009 Corning Cable Systems. All rights reserved. Published in the USA. LAN-525-EN / October 2009
SPECIFICATION SHEET LAN-525-EN | PAGE 16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising