33383.C_xVIDF201x-1x0.w
User’s Guide
SVIDF201x-100 Transmitter &
S/CVIDF201x-110 Receiver Copper-toFiber Video System
SVIDF201x-100
•
•
•
•
•
•
•
AM Video
NTSC, PAL, SECAM compatible
Automatic gain control (AGC)
Real-time full color video
Plug-and-play design for easy installation
CCTV video equipment compatible
Supports RS232, RS422, or RS485 pan/tilt/zoom
data transmission
The SVIDF201x-100 video transmitter at the camera end, when paired with the
xVIDF201x-110 video receiver at the monitor end, enables the transport of analog CCTV
video and pan/tilt/zoom serial data over fiber for extended reach video surveillance or
security installations. The sensitivity of the receiver can be adjusted via on-board DIP
switch settings to extend fiber distance. The xVIDF201x-110 video receiver receives
video signals over fiber; it converts those signals to an analog-composite video stream
and outputs that video stream over coax cable to a video monitor. These models feature
the following:
• Stand-alone video transmitter model (only)
• SC or ST video transmitter fiber port
• One 75-ohm BNC video receiver port
• Pan/tilt/zoom camera capability
SVIDF201x-110
•
•
•
•
CVIDF201x-110
•
•
•
•
Chassis video receiver model
SC or ST transmitter fiber port
One 75-ohm BNC video receiver port
Pan/tilt/zoom camera capability
Stand-alone video receiver model
SC or ST transmitter fiber port
One 75-ohm BNC video receiver port
Pan/tilt/zoom camera capability
xVIDF201x-1x0
xVIDF201x-1x0
Table of Contents
The video transmitter has the following copper connections.
Connector Type
75-Ohm BNC
Number
1
Description
Coax cable, 30.5 m (100 ft)*
Transmitter and receiver models
The various fiber connectors are available on separate models. Single mode and
multimode units come in the following configurations.
Transmitter Models (Stand-Alone only)
Model
SVIDF2011-100
SVIDF2013-100
SVIDF2012-100
Optic Fiber
ST, multimode, 850 nm
SC, multimode, 850 nm
ST, single mode, 1310 nm
Distance*
1 km (0.6 miles)
1 km (0.6 miles)
10 km (6.2 miles)
Receiver Models (Stand-Alone Models)
Model
SVIDF2011-110
SVIDF2013-110
SVIDF2012-110
Optic Fiber
ST, multimode, 850 nm
SC, multimode, 850 nm
ST, single mode, 1310 nm
Distance*
1 km (0.6 miles)
1 km (0.6 miles)
10 km (6.2 miles)
Receiver Models (Chassis Models)
Model
CVIDF2011-110
CVIDF2013-110
CVIDF2012-110
Optic Fiber
ST, multimode, 850 nm
SC, multimode, 850 nm
ST, single mode, 1310 nm
Distance*
1 km (0.6 miles)
1 km (0.6 miles)
10 km (6.2 miles)
*Typical maximum cable distance. Actual distance is dependent upon the physical
characteristics of the network.
Optional accessory
The WMBJ-V wall-mount bracket is used to mount the SVIDF201x-100 transmitter to a
vertical surface.
Part Number Description
WMBJ-V
Wall-Mount Bracket, L 69.9 mm (2.75 in) W: 63.5 mm (2.5 in)
Cautions and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Video System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
SVIDF201x-100 video transmitter parts and functions . . . . . . . . . . . . . . . . . .6
SVIDF201x-110 video receiver parts and functions . . . . . . . . . . . . . . . . . . . .7
CVIDF201x-110 video receiver parts and functions . . . . . . . . . . . . . . . . . . .8
Video Transmitter 5-position terminal block wiring . . . . . . . . . . . . . . . . . . . .9
RS232 TX TB wiring and DIP switch settings . . . . . . . . . . . . . . . . . . . . . . . .9
RS422/485 TX TB wiring and DIP switch settings . . . . . . . . . . . . . . . . . . . . .10
Connecting the camera to video transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Mounting directly to camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Connecting via 75-ohm BNC coax cable . . . . . . . . . . . . . . . . . . . . . . . . . . .11
DIP switches (stand-alone and chassis receiver models) . . . . . . . . . . . . . . . .12
Receiver (RX) wiring the 3-position terminal block . . . . . . . . . . . . . . . . . . . .13
RS232 RX video data TB wiring and DIP switch settings . . . . . . . . . . . . . . .13
RS422/485 RX video data TB wiring and DIP switch settings . . . . . . . . . . . .14
Connecting video receiver to monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Connecting power to stand-alone video receiver . . . . . . . . . . . . . . . . . . . . . . .15
Powering chassis video receiver card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Connecting fiber cable between transmitter and receiver . . . . . . . . . . . . . . . .17
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Video Transmitter LED functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Video Receiver LED functions (stand-alone and chassis models) . . . . . . . . .18
Cable specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Coax cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Fiber cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Video transmitter and receiver LED statuses upon power up . . . . . . . . . . . . .21
Problems and things to check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Contact Us . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Compliance Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
The WMBS wall-mount bracket is used to mount the SVIDF201x-110 receiver to a
vertical surface.
Part Number Description
WMBS
Wall-Mount Bracket, L 81.28 mm (3.2 in.) W: 12.7 mm (0.5 in.)
Note: The information in this user’s guide is subject to change. For the most up-to-date
version of the video transmitter and receiver products, download the user’s
guide from on-line at: www.transition.com.
2
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
3
xVIDF201x-1x0
xVIDF201x-1x0
Cautions and Warnings
Cautions and warning appear here and throughout the manual where appropriate.
CAUTION: Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232,
RS422, RS485, DS1, DS3, Video Coax, etc., are intended to be connected to intrabuilding (inside plant) link segments that are not subject to lightening transients or
power faults. Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB,
RS232, RS422, RS485, DS1, DS3, Video Coax, etc., are NOT to be connected to interbuilding (outside plant) link segments that are subject to lightening transients or power
faults. Failure to observe this caution could result in damage to equipment.
CAUTION: Do not install the media converter in areas exposed to water. Water can
cause damage to internal components, resulting in damaged equipment.
CAUTION: Use 75-ohm BNC connectors on 75-ohm cable only. Failure to observe
this caution will result in signal degradation.
Video System Overview
Figure 1 shows a complete video system containing a SVIDF201x-100 video
transmitter (stand-alone model only) with a camera attached, connected via fiber optic
cable to a SVIDF201x-110 stand-alone receiver with a controller and monitor
connected. The controller sends pan/tilt/zoom data to the camera over the fiber cable.
The receiver is also available in a chassis version, model CVIDF201x-110 which
installs into a Transition Networks Point System chassis, which is not shown in
Figure 1.
Note: For more information about Point System chassis products, we encourage you
to visit our website @ www.transition.com
Camera
SVIDF20
RX
TX
CAUTION: Observe ESD practices when handling printed circuit boards (PCBs).
Failure to observe this caution could result in damage to the PCB.
WARNING: Visible and invisible laser radiation when open. Do not stare into the
laser beam or view the beam directly with optical instruments. Failure to observe this
warning could result in an eye injury or blindness.
AC/DC
Power In
Transmitter
Fiber
Pan/Tilt/Zoom Data (RS232/422/485)
WARNING: Use of controls, adjustments or the performance of procedures other than
those specified herein may result in hazardous radiation exposure.
SVIDF20
DC Power In
Receiver
Pan/Tilt/Zoom Data (RS232/422/485)
Controller
Coax
Monitor
Figure 1: Complete Video System Configuration
Note: The following alphanumeric “xVIDF201x-1x0” is used to include all
versions of the transmitter and receiver.
4
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1--952-941-7600
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
5
xVIDF201x-1x0
xVIDF201x-1x0
Installation -- continued
Installation
SVIDF201x-100 video transmitter parts and functions
SVIDF201x-110 video receiver parts and functions
Top View
Front View
Front View
LEDs QTY 3
IN
RX
Analog Video to
Fiber Media
Converter
TX/RX Fiber Port
TX
Coax Input Port (camera end)
LEDs
PWR-DATA-VID RX
SVIDF
9-24V AC/DC 9-24V AC/DC Data 1 Data 2 SIG GND -
5
4
3
2
1
Coax BNC Video Output
Port (monitor)
LEDs
Qty 3
Rear View
Fiber RX/TX Port
3-Position Terminal
Block (TB)
SW1
1234
Bottom View
Side View
Front View
5-Position Terminal Block (TB)
DIP Switch
DC Power Barrel Connector
DIP Switch
Figure 2: SVIDF201x-100 Video Transmitter Parts
Figure 3: SVIDF201x-110 Video Transmitter Parts
Part
Coax BNC Input Port
Function
• 75-Ohm BNC single connector accepts coax cable—
maximum cable length 30.5 m (100 ft).
Part
Coax BNC Input Port
Function
75-Ohm BNC single connector accepts coax cable—
maximum cable length 30.5 m (100 ft).
• Supports directly connecting the camera to the BNC port.
Accepts ST or SC fiber optic cable connections—cable
distances up to 20 km (12.4 miles) fiber dependent.
Fiber RX/TX Ports
Fiber RX/TX Ports
Accepts ST or SC fiber optic cable connections—cable
distances up to 20 km (12.4 miles) (fiber dependent).
LEDs
• Power (PWR)
LEDs
• Power (PWR)
• D (Pan/tilt/zoom data to camera)
• Data (pan/tilt/zoom to camera)
• V (video signal from transmitter)
• VID RX (video data from receiver)
5-Position Terminal
Block (TB)
DIP Switch
6
• 9 - 24V AC/DC
5
• 9 - 24V AC/DC
4
• Data 1 (+)
3 RS422/485 Data (wire pins 1,2 & 3)
• Data 2 (-)
2 RS232 Data (wire pins 1 & 2)
3-Position Terminal
Block (TB)
DIP Switch
• Data 1 (+)
1 RS422/485 Data, (wire pins 1,2 & 3)
• Data 2 (-)
2 RS232 Data, (wire pins 2 & 3)
• SIG GND
3 (data signal return)
4-position switch sets termination for RS422/485 data and
configures fiber gain to extend fiber distances.
• SIG GND
1 data signal return
Two-position switch can be set to RS232 data or RS422/485
data and termination.
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1--952-941-7600
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
7
xVIDF201x-1x0
xVIDF201x-1x0
Installation -- continued
Installation -- continued
CVIDF201x-110 video receiver card parts and functions
Video transmitter (TX) 5-position terminal block wiring
The SVIDF201x-100 video transmitter comes with an installed 5-position terminal
block (not wired). Wire the terminal block for data and power in accordance with how
the SVIDF20 video transmitter communicates with the camera. Figures 5 and 6 show
each wiring scenario.
Coax BNC Video Output Port
(monitor)
Wire gauge and strip length
LEDs Qty. 3
DIP Switch
Fiber Port TX/RX
•
Use 28-16 AWG wire
•
Strip wires according to manufacturing standards
RS232 video TX TB wiring and DIP switch settings
WARNING: Turn OFF the external power source before installing power wires. Failure
to observe this waring could result in an electrical shock.
3-Position Terminal Block (TB)
Figure 4: CVIDF201x-110 Point System Chassis Card Video Receiver Parts
To wire the terminal block for power and RS232 data, also set the DIP switches, do the
following:
1. Loosen screws 1, 2, 4, and 5 on the TB, shown in Figure 5.
Part
Coax BNC Input Port
Function
75-Ohm BNC single connector accepts coax cable—
maximum cable length 30.5 m (100 ft).
Fiber RX/TX Ports
Accepts ST or SC fiber optic cable connections—cable
distances up to 20 km (12.4 miles) (fiber dependent).
LEDs
3. Set DIP switches “1” and “2” UP (no termination), as shown in Figure 5.
5-Position
Terminal Block
• Power (PWR)
3-Position Terminal
Block (TB)
DIP Switch
2. Insert each wire (power wires first) one at a time into the terminal block; then
tighten the screw to secure the wire.
• D (Pan/tilt/zoom data to camera)
LEDs
R-DATA-VID RX
• V (video signal from transmitter)
9-24V AC/DC - 5
9-24V AC/DC - 4
Data 1 - 3
Data 2 - 2
SIG GND - 1
• Data 1 (+)
1 RS422/485 Data, (wire pins 1,2 & 3)
• Data 2 (-)
2 RS232 Data, (wire pins 2 & 3)
• SIG GND
3 (data signal return)
SVIDF
Power Input
AC or DC
Pin 2, RS232 Data (+)
Pin 1, RS232 Ground
Side View
4-position switch sets termination for RS422/485 data and
configures fiber gain to extend fiber distances.
Bottom View
Note: The CVIDF201 video receiver card installs into a Transition Networks’ Point
System chassis. For more information about Point System chassis products, we
encourage you to visit our website @ www.transition.com
Up
Down
1 2
SW1: UP
RS232 Data
SW2: UP
Always (no termination)
DIP Switch
Figure 5: RS232 Transmitter Data TB Wiring and DIP Switch Settings
8
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1--952-941-7600
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
9
xVIDF201x-1x0
xVIDF201x-1x0
Installation -- continued
Installation -- continued
RS422/485 video TX TB wiring and DIP switch settings
Connecting the camera to video transmitter
Wire gauge and strip lengths
The camera can be mounted directly to the transmitter or connected via a 75-ohm coax
cable with a BNC connector on both ends. When connecting via a 75-ohm coax cable,
a BNC female-to-female coupler is required. See Figure 8.
•
Use 28-16 AWG wire
•
Strip wires according to manufacturing standards
WARNING: Turn OFF the external power source before installing power wires. Failure
to observe this waring could result in an electrical shock.
To wire the TB for power and RS422/485 data, and set the DIP switches, do the
following:
Mounting directly to camera
To mount the camera directly to the transmitter, do the following:
1. Insert the BNC male connector of the transmitter into the BNC connector of the
camera. See Figure 7.
1. Loosen the 5 screws on the TB, shown in Figure 6.
2. Insert each wire (power wires first) one at a time into the terminal block; then
tighten the screw to secure the wire.
Camera
Note: RS422/485 device connectivity requires termination. When using RS422/485
connectivity in a multiple transmitter configuration, terminate the end device
only.
3. Set DIP switches “1 and 2” DOWN for RS422/485 data and termination. See
Figure 6.
RX
Analog Video
to Fiber Media
Converter
Figure 7: Transmitter Directly Mounted to Camera
Connecting via 75-ohm BNC coax cable
5-Position
Terminal Block
LEDs
R-DATA-VID RX
SVIDF
9-24V AC/DC - 5
9-24V AC/DC - 4
Data 1 - 3
Data 2 - 2
SIG GND - 1
Power Input
AC or DC
CAUTION: Use 75-ohm BNC connectors on 75-ohm coax cable only. Failure to
observe this caution could result in signal degradation.
To connect the transmitter to the camera via a 75-ohm BNC coax cable, do the
following:
Pin 3, RS422/485 Data (-)
1. Locate a 75-ohm coax cable with two male BNC connectors.
Pin 2, RS422/485 Data (+)
2. Locate a BNC female-to-female coupler. See Figure 8.
Pin 1, RS422/485 Ground
Side View
3. Insert the BNC female-to-female coupler into the transmitter, shown in Figure 8.
4. Insert one end of the BNC coax cable into the coupler.
5. Insert the other end of the BNC coax cable into the camera. See Figure 8.
Bottom View
SW1: Down RS422/485 Data
Up
Down
1 2
DIP Switch
Camera
75-Ohm BNC Coax Cable
BNC Female-to-Female
Connector
Figure 6: RS422/485 Transmitter Data TB Wiring and DIP Switch Settings
RX
Analog Video
to Fiber Media
Converter
Figure 8: Camera Connected to Transmitter via BNC Coax Cable
10
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1--952-941-7600
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
11
xVIDF201x-1x0
xVIDF201x-1x0
Installation -- continued
Installation -- continued
DIP switches (stand-alone and chassis receiver models)
Receiver (RX) video 3-position terminal block wiring
The 4-Position DIP switch is located on the side of the receiver. See Figure 9. The
switches are used to set termination for RS422/485 pan/tilt/zoom data, also to extend
fiber distances. See Tables 1a and 1b.
The xVIDF201x-110 video receiver comes with an installed 3-position TB (not wired).
Wire the TB for RS232 or 422/485 pan/tilt/zoom data in accordance with how the
SVIDF20 transmitter communicates with the camera. Figures 10 and 11 show each
wiring scenario.
Wire gauge strip lengths
4-Position DIP Switch
2
1
SW1:
UP
Down
No Termination
Termination
3
1 2 3 4
SW2: Gain Set 2
4
SW4: Not Used
•
Use 28-16 AWG wire
•
Strip wires according to manufacturing standards
RS232 RX video data TB wiring and DIP switch settings
To wire the xVIDF201x-110 receiver terminal block for RS232 data and set the DIP
switches, do the following:
SW3: Gain Set 2
1. Loosen screws 1 and 2 on the TB, shown in Figure 10.
Figure 9: 4-Position DIP Switch on Video Receivers
2
Table 1a: DIP Switch Position #1
3. Set the DIP switch “1” UP (no termination), as shown in Figure 10.
Switch 1
UP
DOWN
No-Termination
Termination
Top View Stand-Alone Model
Table 1b: DIP Switch positions #2, #3, and #4 Extend Fiber Distance
Switch 2
UP
DOWN
UP
DOWN
Insert each wire one at a time into the terminal block; then tighten the screw to
secure the wire.
Switch 3
UP
UP
DOWN
DOWN
Switch 4
N/A
N/A
N/A
N/A
Decibel (db)
0 db
+3 db
+6 db
+9 db
Note: Extending fiber distances of the receiver adds the additional decibel
value, shown in Table 1b, to the normal link budget.
Pin 1, RS232 Data (+)
Pin 3, RS232 Ground
SW
1234
SW 1 UP
DIP Switch
No Termination
Side View
Figure 10: RS232 Video Receiver Data TB Wiring and DIP Switch Settings
12
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1--952-941-7600
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
13
xVIDF201x-1x0
xVIDF201x-1x0
Installation -- continued
Installation -- continued
RS422/485 RX video data TB wiring and DIP switch
settings
Connecting video receiver to monitor
Wire gauge strip lengths
1. Locate a 75-ohm coax cable with two BNC connectors at each end.
•
Use 28-16 AWG wire
2. Insert the coax cable into the receiver and monitor, as shown in Figure 12.
•
Strip wires according to manufacturing standards
To connect the video receiver to the monitor, do the following:
Side View
To wire the xVIDF201x-110 receiver terminal block for RS422/485 data, and set the
DIP switches, do the following:
1. Loosen the 3 screws on the TB, shown in Figure 11.
2
Insert each wire one at a time into the terminal block; then tighten the screw to
secure the wire.
Note: RS422/485 device connectivity requires termination. When using RS422/485
connectivity in a multiple transmitter configuration, terminate the end device
only.
Monitor
Receiver Top View
3. Set DIP switch SW “1” DOWN (termination) when using one receiver, as shown in
Figure 11.
SW
1234
Top View Stand-Alone Model
Figure 12: Receiver to Monitor 75-ohm Coax Cable Connection
Pin 1, RS422/485 Data (+)
Pin 2, RS422/485 Data (-)
Pin 3, RS422/485 Ground
Connecting power to stand-alone video receiver
To connect power to the SVIDF201x-110 receiver, do the following:
SW
1234
1. Locate the external DC power supply shipped with the video receiver.
2. Insert the barrel connector on the power cord of the external DC power supply into
the receiver, as shown in Figure 13.
DIP Switch
SW 1 Down Termination
Rear View
Side View
DC Input Power Connector
Figure 11: RS422/485 Receiver Data TB and DIP Switch Settings
Side View
DC Power Adapter Barrel Connector
DC Input Power Barrel Connector
Figure 13: Connecting External Power
14
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1--952-941-7600
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
15
xVIDF201x-1x0
xVIDF201x-1x0
Powering chassis video receiver card
Installation -- continued
Note: The CVIDF201x-110 receiver card is powered by the Point System chassis.
Connecting fiber cable from transmitter to receiver
CAUTION: Observe proper ESD practices when handling printed circuit boards
(PCBs). Failure to observe this caution could result in damage to the PCB.
WARNING: Visible and invisible laser radiation when open. Do not stare into the laser
beam or view the beam directly with optical instruments. Failure to observe this
warning could result in an eye injury or blindness.
To insert the CVIDF201x-110 video receiver into a Point System chassis, do the
following:
1. Position the video receiver card as shown in Figure 14.
To connect the fiber cable from the video transmitter to the video receiver, do the
following:
1. Locate a two-strand fiber optic cable.
2. Slide the receiver card fully into the chassis.
3. Turn the mounting screw clockwise to secure the card to the chassis.
2. Connect the ports of the video transmitter and video receiver devices: TX to RX in
both direction, as shown in Figure 15.
Transmitter
(camera end)
Receiver
(controller/monitor end)
Fiber Cable
IN
RX
Analog Video
to Fiber Media
Converter
TX
Mounting Screw
Point System Chassis
Slot
CVIDF120x-110
Figure 14: Inserting Video Receiver Card into Point System Chassis
Figure 15: Transmitter to Receiver Fiber Cable Connection
Operation
The xVIDF201x-1x0 video system is operational when the camera image at the
transmitter end appears on the monitor at the receiver end. Also, from the controller at
the receiver end, when you can pan, tilt, and zoom in and out the camera. If any of these
functions fail, see the Troubleshooting section. The operational state of the LEDs for
the receiver and transmitter are shown and explained in Figures 16 and 17.
Video transmitter LED functions
DATA
PWR
VID RX
Transmitter LEDs
LED
Power (PWR)
Data
VID RX (receive)
Function
ON Power; OFF = no power
ON fiber link; OFF = no fiber link; FLASHES receiving data
ON fiber link; OFF = no fiber link
Figure 16: Transmitter LEDs
16
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1--952-941-7600
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
17
xVIDF201x-1x0
xVIDF201x-1x0
Operation -- Continued
Technical Specifications
Video Receiver LED functions (stand-alone and chassis
models)
Power
Video
Data
Video
PWR
Transition Networks models SVIDF201x-100 video transmitter specifications.
Video formats:
NTSC, PAL, SECAM
Compliance:
CE Mark; See Declaration of Conformity
Video spec
V
D
D
V
PWR
Power
Data
Stand-Alone Receiver LEDs
LED
Power (PWR)
V (Video)
D (Data)
Use 75-ohm BNC connectors on 75-ohm cable only.
Chassis Receiver LEDs
Operation
ON Power; OFF = no power
= ON fiber link; OFF = no fiber link
OFF no data; FLASHES = sending data
Figure 17: Receiver LEDs
Cable specifications
Output Video:
Bandwidth:
Differential gain:
Differential phase:
Tilt:
Signal/noise ratio:
1-volt pk-pk (75 ohms)
5 Hz - 10 MHz
<5%
< 5°
<1%
60dB
Data formats:
RS232, RS422, RS485
Data rate:
110 b/s – 115 kb/s (serial)
Safety compliance:
Unit: CE Mark
Power supply:
External 12VDC @ 0.5A; 6 W (receiver)
Power input range:
9 – 24VDC or 9 – 24VAC (transmitter)
Power consumption:
2 watts (transmitter and receiver)
Operating temperature:
Coax cables
RG Type:
Gauge:
Impedance:
Distance:
RG-59, RG-6
18–25, single conductor
75 ohms
30.48 M (100 ft) Max
Fiber cables
Storage temperature:
-25°C to 85°C (-13°F to 185°F )
Humidity:
Altitude:
5% to 95%, non-condensing
0 to 10,000 feet
Dimensions:
Transmitter
2.9 in x 3.0 in x 1.0 in (74 mm, 76 mm, 25 mm)
Single Mode
Multimode
9/125µ
62.5/125µ
Receiver
3.3 in x 4.8 in x 1.0 in (84 mm, 122 mm, 25 mm)
Shipping weight:
1 to 2 lbs (45 to 90kg) model dependent
Multimode (ST/SC)
Wavelength:
Link Budget:
Receiver
850 nm
8.0 db
Warranty:
Lifetime
Single Mode (ST)
Wavelength:
Link Budget:
Receiver
1310 nm
12.0 db
Note: Link budgets are specified for normal distances only. For extend distances, see
Table 1b, DIP Switch setting section for the receivers.
18
-25°C to +75°C (-13°F to 167°F) transmitter
-0°C to +60°C (32°F to 140°F) receiver
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1--952-941-7600
WARNING: Visible and invisible laser radiation when open. Do not stare into the
beam or view the beam directly with optical instruments. Failure to observe this
warning could result in an eye injury or blindness.
WARNING: Use of controls, adjustments or the performance of procedures other than
those specified herein may result in hazardous radiation exposure.
CAUTION: Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232,
RS422, RS485, DS1, DS3, Video Coax, etc., are intended to be connected to intrabuilding (inside plant) link segments that are not subject to lightening transients or
power faults. Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232,
RS422, RS485, DS1, DS3, Video Coax, etc., are NOT to be connected to inter-building
(outside plant) link segments that are subject to lightening transients or power faults.
Failure to observe this caution could result in damage to equipment.
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
19
xVIDF201x-1x0
xVIDF201x-1x0
Troubleshooting
Troubleshooting -- continued
Troubleshooting the xVIDF201x-1x0 transmitter and receiver video monitoring system
should be done from the systems perspective. See Figure18.
Camera
SVIDF20
Upon system power up: Power, Data, and VID RX LEDs on the transmitter should be
ON; the Power (PWR) and Video (V) LEDs on the receiver at the controller end
should be ON. See Figure 19.
RX
TX
AC/DC
Power In
Transmitter
Video transmitter and receiver LED statuses upon
power up
Fiber
On
On
Pan/Tilt/Zoom Data (RS232/422/485)
On
On
On
PWR
V
D
SVIDF20
Off
Transmitter LEDs
Receiver LEDs
DC Power In
Figure 19: Power UP Transmitter and Receiver LED Status
Receiver
Pan/Tilt/Zoom Data (RS232/422/485)
Problems and things to check
Controller
Coax
1.
If either power LED is not lit:
• Check that the main power source is active for both devices.
• Check that the power adapter for both devices is plugged into an active AC
source.
• Check that the terminal block on the video transmitter (pins 4 & 5) have
stripped wires inserted.
• At the receiver end, ensure that the power adapter power-cord barrel (for
standalone models only) is fully insertion into the barrel connector on the rear
of the stand-alone receiver.
• At the receiver end, if using a video chassis receiver card, ensure that the card
is fully inserted into the chassis.
• Contact technical support 24-Hour Technical Support: 1-800-260-1312 -International: 00-1--952-941-7600.
2.
If the transmitter VID RX LED is not lit:
• When the video transmitter is directly mounted to the camera: check that the
transmitter is fully inserted onto the camera’s BNC connector.
• When the video transmitter is connected to the camera via a coax cable, check
that the cable is properly inserted into the camera and video transmitter.
• Check that power is turned ON to the camera.
• Contact technical support 24-Hour Technical Support: 1-800-260-1312 -International: 00-1--952-941-7600.
Monitor
Figure 18: Video System Configuration
Note: The system is functioning properly when the image from the camera is
accurately presented on the monitor; also, the controller at the receiver end can
send pan/tilt/zoom commands to function the camera mechanically.
20
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1--952-941-7600
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
21
xVIDF201x-1x0
xVIDF201x-1x0
Troubleshooting -- continued
Contact Us
Problems and things to check -- continued
3.
4.
5.
If the monitor does not show the camera’s image:
• Check that the receiver’s video (V) LED is lit.
• Check that the fiber cable from the video transmitter fiber TX port is properly.
connected to the receiver’s fiber RX port.
• Check that the monitor is plugged into power and turned ON.
• Check that the BNC coax cable is properly connected from the video receiver
to the monitor.
• Contact technical support 24-Hour Technical Support: 1-800-260-1312 -International: 00-1--952-941-7600.
If the transmitter data LED is not lit:
• Check that the video receiver’s TX port’s fiber cable is properly connected to
the video transmitter’s RX fiber port.
• Check that power is turned ON to the receiver (PWR LED).
• Contact technical support 24-Hour Technical Support: 1-800-260-1312 -International: 00-1--952-941-7600.
If the camera will not function (pan/tilt/zoom) mechanically:
• Check that the TB on the video transmitter is wired properly for RS232 or
422/485 data. (see Installation section “wiring the 5-position terminal block.”)
• Check that the 3-position TB on the xVIDF201x-110 video receiver is wired
properly for RS232 or 422/485 data. The wiring sequence is the same as that
of the SVIDF201x-100 video transmitter’s TB.
• Check that the DIP switches are properly set up for RS232 data or RS422/485
data.
• Contact technical support 24-Hour Technical Support: 1-800-260-1312 -International: 00-1--952-941-7600.
Technical support
Technical support is available 24 hours a day.
US and Canada:
1-800-260-1312
International:
00-1-952-941-7600
Transition now
Chat live via the Web with Transition Networks Technical Support.
Log onto www.transition.com and click the Transition Now link.
Web-based seminars
Transition Networks provides seminars via live web-based training.
Log onto www.transition.com and click the Learning Center link.
E-Mail
Ask a question anytime by sending an e-mail to our technical support staff
techsupport@transition.com
Address
Transition Networks
10900 Red Circle Drive, Minnetonka, MN 55343, U.S.A.
telephone: 952-941-7600, toll free: 800-526-9267, fax: 952-941-2322
Declaration of Conformity
Declaration of Conformity
Name of Mfg:
Model:
Part Number(s):
Regulation:
Purpose:
Transition Networks
10900 Red Circle Drive, Minnetonka MN 55343 U.S.A.
SVIDF201x-100 Transmitter & xVIDF201x-110 Receiver
SVIDF2011-100, SVIDF2012-100, SVIDF2013-100
SVIDF2011-110, SVIDF2012-110, SVIDF2013-100,
CVIDF2011-110, CVIDF2012-110, CVIDF2013-100
EMC Directive 89/336/EEC
To declare that the SVIDF201x-100 Transmitter and
xVIDF201x-110 Receiver to which this declaration refers is in
conformity with the following standards:
CISPR 22:1997+A1:2000 + A2:2003; EN 55022:1998+A1:2000 +
A2:2003; EN55024:1998+A1:2000 + A2:2003; Class A; FCC part
15 subpart B; 21 CFR subpart J
I, the undersigned, hereby declare that the equipment specified above conforms to the above
Directive(s) and Standard(s).
August 2008
Stephen Anderson, Vice-President of Engineering
22
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Date
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
23
xVIDF201x-1x0
Compliance Information
FCC regulations
This equipment has been tested and found to comply with the limits for a class A digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which
case the user will be required to correct the interference at the user's own expense.
Canadian regulations
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out
on the radio interference regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage
radioélectrique édicté par le ministère des Communications du Canada.
European regulations
WARNING: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
ACHTUNG! Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei
Betrieb dieses Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für
Gegenmaßnahmen verantwortlich.
ATTENTION! Ceci est un produit de Classe A. Dans un environment domestique, ce produit
risque de créer des interférences radioélectriques, il appartiendra alors à l'utilsateur de prende les
measures spécifiques appropriées.
In accordance with European Union Directive 2002/96/EC of the European Parliament
and of the Council of 27 January 2003, Transition Networks will accept post usage returns
of this product for proper disposal. The contact information for this activity can be found
in the 'Contact Us' portion of this document.
CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.
Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EGMitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der
Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über
Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer
Konformität.
Trademark notice
All trademarks and registered trademarks are the property of their respective owners.
Copyright restrictions
© 2003, 2005 Transition Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means:
graphic, electronic, or mechanical - without written permission from Transition Networks.
24
Printed in the U.S.A.
33383.C
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising