GDO Accessories

GDO Accessories
CHAMBERLAIN
Keyless Entry System
Model 65C
Owners Manual
CONSOLE
KEYBOARD
The Keyless Entry System consists of a keyboard and a console. The keyboard sends a coded signal from outside
the garage. The console fastens to an inside garage wall. It receives the 4-digit programmed coded signal and
starts the door opener. The Keyless Entry System will work with most Genie “Push Twice to Operate” openers if
you press any other digit after you enter the 4-digit programmed code.
NOTE: CABLE CONNECTOR HOLE IS LOCATED ON LEFT SIDE OF CONSOLE. IF POSSIBLE,
INSTALL KEYLESS ENTRY SYSTEM ON LEFT SIDE OF GARAGE (DETERMINED BY FACING
GARAGE FROM OUTSIDE). IF INSTALLED ON RIGHT SIDE OF GARAGE, CABLE MUST BE ROUTED
OVER OR UNDER CONSOLE.
FEATURES OF KEYLESS ENTRY SYSTEM
Personalized Code: 10,000 possible combinations. Code
can be changed easily if desired.
Operation: Opener activates when programmed code is
entered on keyboard.
The user has 10 seconds from the time the first number is
pressed to enter the 4-digit code.
If incorrect numbers are accidentally pressed, a 5 second
interval is necessary before starting over.
Power Supply: Operates from the garage door opener
power with a battery back-up for code memory and lighted
keyboard.
Installation: Simple to install in 6 easy steps.
Console: provide an additional push button control to
operate door from inside garage.
Keyboard: The garage door can be operated after a
valid code entry by pressing ANY single key AS LONG
AS THE KEYBOARD LIGHT REMAINS ON.
Keyboard illuminates and remains lit for 10 seconds
when ANY number is pressed. In darkness this feature
allows user to press ANY number before entering the
4-digit code.
THE UNIT WILL NOT OPERATE WITHOUT A BATTERY.
IMPORTANT NOTE: When illumination is needed,
avoid pressing keyboard area which contains the
first code number.
DISCONNECT THE POWER TO THE GARAGE DOOR OPENER BEFORE BEGINNING INSTALLATION.
STEP 1-ONE PIECE DOORS: Install the keyboard on
the exterior front wall of a FRAME garage. Position it
away from the door opening to avoid injury as door
swings out and up. Drill a 1” diameter hole through wall
at eye level. Refer to note below; then proceed to Step 2.
STEP 1-SECTIONAL DOORS: Draw two intersecting
lines on garage jamb face-horizontally at eye level and
vertically as close to centerline as possible. Make sure
there is at least 1-1/4” clearance on each side of the
vertical line. Drill a 1” diameter hole through the jamb at
marked location.
Refer to illustration on Side 2 if your garage has a
built-up jamb.
NOTE: If garage is constructed of material other
than wood (brick, stone or aluminum siding), install
keyboard on door jamb with this important
exception: LOCATE KEYBOARD ON OUTSIDE
EDGE OF DOOR JAMB TO AVOID INJURY AS
DOOR SWINGS OUT AND UP.
PARTS LIST
Console Assembly.........................41D2995
Keyboard Assembly.......................41D2994
9 Volt Battery......................................10A15
2 Strand Bell Wire...........................217A197
Transformer Kit (inc. bell wire)........Model 95
Side 1
NO USER SERVICEABLE PARTS.
For service information, Call Toll Free:
1-800-654-4736
NOTE: If your garage has a built up jamb, drill the hole 2” deep.
Then, on the inside edge of jamb, drill a second hole into first hole
to complete access.
STEP 5: Run bell wire up wall and across ceiling to garage door
opener terminals. Use insulated staples to secure wire. Cut off
excess length.
ON CHAMBERLAIN GARAGE DOOR OPENERS:
If opener terminals are colored, connect white wire to white
terminal and red wire to red terminal. If terminals are not colored,
connect wire to push button terminals (red wire to the left-most
terminal as you face opener; white wire to adjacent terminal).
ON OTHER BRAND GARAGE DOOR OPENERS: polarity must
be observed. Attach red wire to push button terminals #1 (leftmost terminal as you face the opener) and white wire to push
button terminal #2.
STEP 6: Pry open front panel of console with coin or
screwdriver. Snap a 9 volt battery onto circuit board connector
and drop into console. DO NOT replace panel at this time.
STEP 2: Hold keyboard firmly with the back of the case UP.
position thumb against bottom of case and pull up sharply.
Keyboard will lift out of cover, allowing access to bottom mounting
hole.
Guide the keyboard cable through hole to inside of garage. Position
the keyboard against outside jamb. Drill two 1/8” pilot holes for
fastening screws. Attach securely with (2) 6ABx1-1/4” screws. Close
cover.
Excess cable can be folded and inserted into the access hole to
keep it out of the way.
SET THE CODE
STEP 3: Connect the 2-strand bell wire by color to terminals on
back of console-red wire to terminal #1 and white wire to terminal
#2. Insert keyboard cable connector into slot on side of console.
Be sure connector guides are facing BACK of console.
IMPORTANT: Some garage door openers have a third screw
terminal which supplies power to the radio control. This
terminal can be connected to terminal #3 on the console
with a third strand of bell wire (not supplied).
Move program/operate switch near the battery to PROGRAM
position (keyboard light should flash).
NOTE: If the light does not flash, check cable and battery
connections. Press any four numbers on keyboard.
CAUTION: For security, do not use address, license or
consecutive numbers (1,2,3,4 etc.)
Move the program/operate switch to OPERATE position (the
keyboard light will go off).
With any garage door opener made by Stanley, accessory
Transformer 95 MUST be installed.
Reconnect power to garage door opener. If you have installed
Transformer Model 95, plug the transformer into a 120 Volt
outlet. Enter the code on the keyboard. If the door operates
properly, replace the front panel on the console.
TRANSFORMER INSTALLATION INSTRUCTIONS: Connect
one end of the 2-strand bell wire supplied with the kit to each of
the transformer terminals (no polarity). Connect the other end of
bell wire to terminals 1 and 3 on the Keyless Entry console.
Loss of power to either the battery or the garage door opener
will not affect the programmed code. However, if BOTH lose
power, the code must be reset.
IF THIS ACCESSORY IS USED WITH ANY GARAGE DOOR
OPENER OTHER THAN SEARS OR CHAMBERLAIN AND
THE BATTERY FAILS IN TWO MONTHS, TRANSFORMER
MUST BE INSTALLED. Follow instructions above.
STEP 4: Position console on an interior garage wall
approximately one foot from outside edge of door.
Fasten (2) screws provided.
©
114A1244
Battery should produce adequate power for at least one year. If
light in keyboard does not turn on, change the battery.
NOTE: To maintain the privacy of your code, keep all the
buttons free from soil. If any of the numbers show signs of
wear, change your code.
1990, Chamberlain Mfg. Canada, Inc.
All Rights Reserved
Printed in Mexico
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising