Quest QX-3701 Clock / Radio / CD Player Owners Manual

Quest QX-3701 Clock / Radio / CD Player Owners Manual
_ OWNER’S MANUAL
QX-3701
IN-WALL TIME CLOCK /AM/FM RADIO AND
COMPACT DISC PLAYER
RISK OF ELECTRIC SHOCK
DO NOT OPEN.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOSTURE. DO NOT OPEN CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
the triangle is a warning sign alerting you is a warning sign alerting you of important
The lightning flash and arrowhead within | The exclamation point within the triangle
of “dangerous voltage” inside the product. Instructions accompanyıng the product.
Please record the serial number located on the rear of the unit in the space below.
Serial Number
IMPORTANT NOTES
* Avoid installing the unit in locations described below: es Operate controls and switches as described in the manual
- Places exposed to direct sunlight or close to heat Before turning the power switch on for the first time, make
radiating appliances such as electric heaters. sure all necessary connecting cords are properly installed.
- On top of other stereo equipment that radiates too much
heat.
- Places lacking ventilation or dusty places.
- Humid or moist places.
IMPORTANT SAFEGUARDS
SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR AUDIO EQUIPMENT.
(FOR U.S.A)
CAUTION:
Read all of these instructions.
Save these instructions for later use.
Follow all warnings and instructions marked on the
audio equipment, с
Read Instructions — All the safety and operating
instructions should be read before the appliance 1s operated.
Retain Instructions — The safety and operating instructions
should be retained for future reference.
Heed Warnings — All warnings on the appliance and in the
operating instructions should be adhered to.
Follow Instructions — All operating and use instructions
should be followed.
Water and Moisture — The appliance should not be used
near water, for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement or near a Swimming
pool.
be used only with a cart or stand that is
Carts and Stands — The appliance should
recommended by the manufacturer.
6A. An appliance and cart combination
should be moved with care. Quick stops ,excessive force,
and uneven surfaces may cause the appliance and cart
combination to overturn.
Wall or Ceiling Mounting — The appliance should be
mounted to a wall or ceiling in accordance with the
mounting dimensions.
Ventilation — The appliance should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the appliance should not be
situated on a bed, sofa, rug or a similar surface that may
block the ventilation openings; or place in a built-in
installation, such as a bookcase or cabinet that may impede
the flow of air through the ventilation openings.
10.
11.
12.
13.
14.
15.
16.
Heat — The appliance should be situated away from heat
sources such as radiators, heat registers, stoves, or other
appliances (including amplifiers) that produce heat.
Power Sources — The appliance should be connected to a
power supply only of the type described in the operating
instructions or as marked on the appliance.
Grounding — The precautions that should be taken so that
the grounding means of the AC connecting power cord 1s
not defeated.
Power-Cord Protection — Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the appliance.
Cleaning — The appliance should be cleaned with a slight
dampened cloth. Do not use harsh chemicals, cleaning
solvents, strong detergents, etc.
Power lines — An outdoor antenna should be located away
from power lines.
For Speaker Connections — Eighteen (18) American Wire
Gauge (AWG), Standard Wire, or larger, must be used. The
wire of preference is 18/2 AWG Standard. Failure to use 18
AWG Standard Wire, or larger, will void the product
warranty. |
Outdoor Antenna Grounding — If an outside antenna is
connected to the receiver, be sure the antenna system is
grounded so as to provided some protection against voltage
surges and built up static charges. Section 810 of the
National Electrical Code. ANSI/NFPA NO. 70-1984,
provides information with respect to proper grounding of
the mast and supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of grounding
conductors, location of antenna-discharge unit, connection
to grounding electrodes and requirements for the grounding
electrode. See Figure below.
EXAMPLE OF ANTENNA GROUNDING ACCORDING
TO NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-200
GROUNDING CONDUCTORS
{NEC SECTION 310-20}
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
{NEC ART 258, PART H}
Notes:
a. Use No. 10 AWG copper or No. 8 AWG aluminium or No. 17
AWG copper plate steel or bronze wire, or larger as ground
17
18.
19.
20.
wire for both mast and lead-in.
. Secure lead-in wire from antenna to antenna discharge unit
and mast ground wire to house with stand-off insulators,
spaced from 4 feet (1.22 meters) to 6 feet (1.83 meters) apart.
. Mount antenna discharge unit close as possible to where lead-
in enters house. An outside antenna system should not be
located in the Vicinity of overhead power lines or other
electric light or Power circuits, or where it can fall into such
power lines or Circuits. When installing an outside antenna
system, extreme Care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.
. Non-use Periods — The power cord of the appliance should
be unplugged from the outlet when left un-used for a long
period of time.
Object and Liquid Entry — Care should be taken so that
objects do not fall and liquids are not spilled into the
enclosure through openings.
Damage Requiring Service — The appliance should be
serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the
appliance or other moisture.
C. The appliance has been exposed to rain.
D. The appliance has been dropped, or the enclosure
damaged. |
Servicing — The user should not attempt to service the
appliance beyond that described in the operating
instructions. All other servicing should be referred to
qualified service personnel,
FRONT VIEW: 6
11
30
12
28
27.
26
25
24
23
16
22 21 20 19 18 17
BACK VIEW
31
—
|
©
N |
©
32
33
34
35
36
37
38
WIRE CONNECTION
SPEAKERS DIAGRAM
BLACK (-) GROUND
RED (+) BATTERY
LEFT SPEAKER(A)
15,
Jia
LEFT SPEAKER(B)
CONNECTOR
I
YELLOW (+) BACK UP
RIGHT SPEAKER(A)
+ BROWN GREY +
— GREY W/BLK BLUE W/BEK —
+ PURPLE BLUE +
RIGHT SPEAKER(B}
+ ORANGE | WHITE +
| pi ir
| — WHITE W/BLK
LEFT SPEAKER(C)
RIGHT SPEAKER(C)
CONTROLS:
ю о носом оке юн
о ю MR UNE SS
Sleep Button
Mute Button
CD Button
Repeat Memo -up Button
Remain Button
Memo Button
AUX. Button
Band Button
Tuner Button
Mode Button
. Set Button
. Volume Control
Balance Knob
. Tone Knob
Open/Close Button
. CD/AUX Input Jack
. Intro Button
Random Button
CD FWD-Skip Button &Tuner Up Button
. CD REV-Skip Button & Tuner Down Button
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
CD Stop Button
CD Play /Pause Button
Headphone Jack
Weather Band Tuning Knob
Weather Band Button
Auxiliary Speaker C Selection Button
Auxiliary Speaker B Selection Button
Main Speaker A Selection Button
Reset Button
Power Button
AM/Weather Band Antenna Post
AM/FM Antenna Jack
Aux. Input Left Channel
Aux. Input Right Channel
Line Output Left Channel
Line Output Right Channel
DC Out Jack
DC In Jack
INTRODUCTION
The QX-3701 is a compact electronic audio device with functions of a CD player, AM/FM Radio Player integrated in ONE. The slim
cabinet construction makes the unit an ideal wall radio for homes, recreational vehicles, custom vans, hotels/motels, etc.
Its features include:
— AM/FM Stereo Tuner
— Weather forecast Tuner
—— Radio station preset
— Laser Compact Disc Player
— Main Speaker A, Auxiliary Speaker B , and Auxiliary Speaker C Output System.
— LCD Display
— CD Track Memory
— Line Output Jack
— Aux./CD IN Jack
— Alarm & Time Clock
— Headphone Jack
NOTES:
1. Connect the required speakers before operating the unit.
2. Use external antenna for optimum radio reception when necessary.
Speaker Installation
The QX-3701 1s designed with outputs for speakers, main speaker À , Auxiliary Speaker B, and Auxiliary Speaker C . Main Speaker А
output system 1s the master speaker output and 1s for the speaker-pair installed closest to the unit.
Auxiliary Speaker B output system provides an additional speaker output pair for use in another location,
9
Auxiliary Speaker C output system provides you an additional speaker output pair for use in another location.
To install a speaker-pair to the Main Speaker A output system
1. Select two to four 4-ohm speakers.
2. To wire speakers refer to the wire connection diagram. (Page 7)
If you also want to install speakers to the Auxiliary Speakers, simply repeat steps 1 through 2.
CAUTION: Fach speaker output channel is marked with “+” and “=”. Do not electrically connect them together.
EXTERNAL ANTENNA INSTALLATION
1. When installing an external antenna, pay close attention to the antenna safety instructions in “IMPORTANT SAFEGUARDS”.
2. To connect your external antenna to the unit's antenna jack, first have the external antenna’s connecting wire equipped with a
suitable connector that fits the antenna jack, then plug the connector into the jack. |
3. AM/FM ANTENNA JACK - You can receive AM and FM signals by connecting the external antenna to it.
LINE OUTPUT
1. Line Output Right Channel For external connection to the Right Channel Input of your own amplifier.
2. Line Output Left Channel For external connection to the Left Channel Input of your own amplifier.
AUX.INPUT
1. Function Switch to the AUX position.
2. CD IN/AUX on front panel or AUX IN Jack on back of the unit is for input of external CD or other AUXILIARY source,
Notes:
1. When connecting Line Output or Aux. Input jacks, remember to switch off both the QX-3701 and your amplifier or external source.
2. Each channel is marked “Right” and “Left”. Do not reverse the connections (AUX INPUT Jack is located on the rear of the unit)
10
3. CDIN/AUX isa 3.5mm stereo plug input jack. (CD IN/AUX Jack located on the front panel.)
DC OUT JACK
The DC Output Jack is centered negative “ RCS) ”, Allows you to Connect it to your own amplifier.
Note: 1.When connecting DC OUT jack , remember to power off both the QX-3701 and your own amplifier.
2. Ensure polarity is correct.
3. The DC Output 1s available while the power of QX-3701 is turned on,
DC IN JACK
The DC In Jack is that the external power source for connecting the AC adaptor to the unit.
The DC in jack is centered negative “® Oo ”. The DC IN jack is equal to the black wire and red wire on the back of QX-3701.
HEADPHONE JACK
This unit 1s equipped with a Headphone Jack,
NOTE: Main speaker A, Auxiliary Speaker B, and Auxiliary Speaker C will all be louden when the headphones is plugged in.
CLOCK & ALARM SETTING
To start the clock setting mode, Press the SET button (alarm time will begin to flash). Once in clock setting mode each press of the SET
button will cycle the clock as follows:
I¥ Press: Alarm hour will flash
2" Press: Alarm minute will flash
3 Press: Month will flash
4" Press: Date will flash
5" Press: Hour will flash
6” Press: Minute will flash
Once the function you wish to set begins to flash (alarm hour, alarm minute, month, etc.) press the MODE button to change to desired
11
setting. Press the SET button to move to the next function.
ALARM OPERATION
Once the desired time for the alarm has been set (see CLOCK & ALARM SETTING)
turn on the alarm as follows:
Cl.
1. Press the SET button (alarm time will begin to flash).
2. Press the MODE button (a small bell will appear indicates the alarm 1s on).
3. Pressing the MODE button a second time will turn on both alarm and hourly chimes. (Both the alarm indicator and chimes indicator
will appear in the right hand corner of the display).
4. Pressing the MODE button for a third time will turn only the chimes on (chimes ring hourly).
5. Pressing the MODE button for a forth time will turn both the alarm and chimes off.
RADIO OPERATION
1. Press POWER button to “ON” position.
2. Press the TUNER button.
3. Set VOLUME to desired level.
4, Press SPEAKER Select Switch (A) for (A) Speakers to have sound.
Press SPEAKER Select Switch (B) for (B) Speakers to have sound.
Press SPEAKER Select Switch (C) for (C) Speakers to have sound.
5. Switch the BAND Switch to your desired band. (AM, FM Stereo).
6. Press Tuner button UP or DOWN to tune into your desired station.
RADIO STATION PRESETS
While in tuner mode, select station you wish to preset.
2. Press the MEMO button (CH 00 will begin to flash in left hand corner of the display).
3. Press the REPEAT/MEM-UP button to select the preset number you wish to set.
4. Press the MEMO button to confirm the setting.
12
WEATHER BAND OPERATION
1. Press the system POWER button to “ON” position.
2. Press the “WEATHER ” button,
3. Adjust WEATHER TUNING Control knob to locate desired weather forecast in your area.
Note: Weather function can be used in any mode.
CD OPERATION
To Play a Compact Disc
1. Press the POWER button to the “ON” position.
2. Press CD button.
3. Press the OPEN/CLOSE button to open the disc tray.
4. Place the CD into tray with the printed side facing up. Press the OPEN/CLOSE button again to close the disc tray.
5. Disc information will appear on the LCD display. (Disc information includes the total track numbers and playing time)
6. Press the PLAY/PAUSE button to play CD. |
7. To stop playing, press the STOP button.
Note: When you can’t open the disc tray, you can press again the OPEN/CLOSE button.
SKIP DURING PLAY MODE
1. Press the FWD-SKIP button to skip to the beginning of the next track.
2. Press the REV-SKIP button to skip to beginning of the current track.
SEARCH DURING PLAY MODE
1. Press and hold FWD-SKIP button or REV- SKIP to quickly advance or reverse through the music at high speed.
2. Release the FWD-SKIP button or REV-SKIP button to return to normal playing mode.
REPEAT
1. Press the REPEAT MEM-UP button to enter the one track repeat playing mode. The LCD will display “REPEAT ”.
13
2. Press the REPEAT MEM-UP button again to enter the all tracks repeat playing mode. The LCD display will flash “REPEAT ”
3. Press the REPEAT MEM-UP button again to cancel the repeat function.
PAUSE MODE
1. While playing a CD press the PLAY/PAUSE button to pause playing.
2. Press the PLAY/PAUSE button again to continue playing.
INTRO OPERATION
1. While In CD mode press the INTRO button to start the introductory scan mode.
2. Press the INTRO button again to stop the introductory scan mode.
RANDOM OPERATION
1. In CD mode press the RANDOM button to start the random playing mode.
2. Press the RANDOM button again to stop the random playing mode.
MEMORY
1. While in standby mode, press memory button.
2. Select the track’s location number using REPEAT MEM-UP button.
Press the MEMORY button again to confirm.
MUTE
Press the MUTE Button to mute all sound.
SLEEP
Press the SLEEP Button to turn off the music at specific time set,
REMAIN
Press the REMAIN Button to review remain time in playing CD.
14
RESET BUTTON
If the QX-3701 is power on, But doesn’t work normally. You can press the reset button.
MOUNTING DIMENSIONS
Pan Philips head screw 35mm x 40 mm x 4 pcs
Remark: Opening dimensions in wall is 206mm(Width) x 248mm(Height)
15
226) Dre
HA aa
SPECIFICATIONS:
Power Supply
Main Speaker A
Auxiliary Speaker B
Auxiliary Speaker C
Audio Output Power
Speaker A+B+C
Dimensions
Radio Section
Frequency Ranges
Weather Section
Frequency Ranges
CD Section
CD Type
Frequency Response
S/N Rate( A filter )
1) DC adaptor (Not included)
2) Input: DC 12V 5A
4-ohm speaker, Max.2
4-ohm speaker, Max.2
4-ohm speaker, Max.2
5W (Мах.)
204mm (L) x 240mm(H) x 140mm (D)
AM 520 — 1710KHz
FM 87.5 — 108 MHz
162.2MHz-162.7MHz
Front Loading
20 Hz-20KHz
90dB at 1 KHz (dB
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising