How to install and operate the X-D11 digital mono amplifier

How to install and operate the X-D11 digital mono amplifier
How to install and
operate the
digital mono
This owners manual is written in easy english and
uses a lot of drawings to simply the installation and
use of the above amplifier.
Your X-program amplifier must be installed correctly
in order to work well. This manual will show you how
to install the amplifier like a pro. Please read the
entire manual before beginning the installation.
Install the amplifier yourself if you feel confident with
our instructions and if you have the proper tools.
However if you feel unsure, turn over the installation
job to someone better suited to it.
Warranty Service
This amplifier is covered by warranty, depending on
the conditions in the country where it is sold. If the
amplifier is returned for service, please include the
original dated receipt with the product.
Technical Assistance
For technical assistance ask the shop where the
product was sold or the distributor in your very country.
You can always phone the DLS Helpdesk in Sweden
+ 46 31 84 00 60 or send an e-mail to
Information can also be found on our WEB-site
DLS Svenska AB
P.O. Box 13029
S-40251 Göteborg, Sweden
Tel: +46 31 840060
Fax: +46 31 844021
Tools and materials needed……….
Amplifier installation kit…………....
Routing Wires……………………....
Power and Outputs……………..….
Inputs and controls………………...
Input level control..........................
Phase control.....………………...…
Bass boost control.........................
Speaker wiring:
Single amplifier system………….….
Bridging two amplifiers...................
Professional tips……………………..
Number of channels
Power output in 4 ohm (0,4% THD)
1 x 400 W
Max output in 2 ohm (0,7% THD)
1 x 750 W
Max output in 1 ohm (1% THD)
1 x 1050 W
All above output power ratings at 13,8 Volt
Signal to noise ratio, A-weighted
>100 dB
Damping factor
Frequency response
15 Hz - 160 Hz
Input impedance, low level
10 kohm
Input impedance, high level
100 ohm
Input sensitivity
0,15 - 5V
Phase control 0-180 degrees variable yes
Remote bass boost control
Bass boost adjustable gain @45 Hz 0 - +18 dB
Filter subsonic, 24 dB slope
15 - 50 Hz
Filter lowpass 24 dB slope
15 - 150 Hz
Bridge mode (master/slave selector) Yes
Max size for power cables
21 mm2 (4AWG)
Max size for speaker cables
10 mm2 (7AWG)
Power consumption, idle
1,5 A
Maximum current draw
120 A
Built-in fan cooling
4 x 30A
Dimensions (mm)
Dimensions (inch)
5,3 kg (11,7 lb)
Approval of electromagnetic compatability according
to the EEC Directive 72/245/EEC and 2006/96/EC
E 13
Approval No: 03 6367
We follow a policy of continuous advancement in
development. For this reason all or part of specifications
& designs may be changed without prior notice.
X-D11 include
RCA input and output
High level input with auto start
Continuous variable low pass crossover
Continuous variable subsonic crossover
Bass boost feature
Remote bass level control
Phase control cont. variable 0-180 degrees
Bridge mode master / slave selector
Electronic protection circuitry against
short-circuit, DC offset and thermal overload.
Before you begin the install
Before you begin you need to read the manual, to have
some tools, cables and other material available. There
is one such list of material on the following page.
Amplifier location
Allow air circulation around the amplifier.
The X-program series of amplifiers have a compact
design that allows great flexibility in mounting. You
can mount it under a seat or in the trunk.
When you select a location, do remember that the
amplifier generates a lot of heat.
Choose a location where air can circulate freely
around the amplifier. Do not cover the amplifier with
carpets or hide behind trim panels.
Do not mount the amplifier in an inverted or upside
down position.
Check all locations and placements carefully before
making any cuts, drilling any holes or making any
Disconnect Battery
Before starting the installation, always disconnect
the negative terminal of
the battery.
If problems occur during the installation, or later,
this guide might help you to find out whats´s wrong.
The amplifier is dead:
1. Check power lead, ground and connections at
the amplifier using a multi meter.
2. Check the battery terminal connections.
3. Check the power lead fuse or circuit breaker. If
fuse damage continues, inspect the power lead
for short circuits.
4. Check the amplifier protection fuses. Are these
broken change to new ones with the same value.
If short circuiting continues, contact your local
DLS dealer. A fault may exist in the amplifier.
5. To start the amplifier requires a remote voltage
of 9-15 volt. Check the voltage with a multi meter.
Amplifier protection fuse blows at low volume:
One or more speaker cables are shorted. Make an
insulation test with a multi meter. The cables must
not have a connection to earth.
The amplifier turns off after 10-30 minutes:
The amplifier is overheating due to inadequate ventilation. Check mounting position is free from
1. Move the amplifier to a place with better ventilation.
2. Install one or two fans to cool down the heatsink.
3. Overheating can also be caused by an
impedance load below the level permitted.
No output from the speakers:
Check the following:
1. Speaker cable connections to both amplifier and
2. Signal lead plugs and cables.
Fasten the amplifier to the surface using the four
separate brackets coming with the amplifier. The
brackets are attached to the amplifier with screws
and can be directed in two ways, see figure:
Mount the flanges this way,
or this way.
X-logo on amplifier cooling flange
The X-logo on the amplifier top is attached with two
1 mm hex. screws. The logo can be removed and
twisted 90 or 180 degrees, and then screwed back
in wanted position. The logo can be mounted in four
different ways to match your installation.
Bottom plate of amplifier
Tools and material needed
Routing wires
Flat and Phillips screwdrivers
Wire cutter
Wire stripper
Electric drill with drills
Crimping tool
Digital multimeter or test lamp
Wire brush, scraper or a piece
of an abrasive sheet to remove
paint for a good ground connection
Grease to protect the ground
connection from corrosion
head unit
Speaker wire: minimum
12 AWG = 4 mm2 for subwoofers
Sheet metal screws for mounting the
amplifier to the amplifier board and the
amplifier board to the car + some extra
for fuse holder, amplifier ground etc.
Electrical insulation tape
½ inch thick plywood or particle board for
the amplifier to be mounted upon.
Amplifier installation kit:
If available,buy an amplifier installation kit. It
contains normally all you need. This is what you
have to buy if you buy the items separately
20- 25 feet = 6- 7.5 meter power cable,
preferably AWG 4 = 21 mm2 or heavier
1 pc of fuseholder to install close to the
car battery + fuse 100 Ampere.
20 feet of AWG 15 = 1,5 mm2 wire for
remote turn on / off cable from radio.
RCA-cable for input from radio.
- 20 feet or 5 meter for trunk installations
-12 feet or 2 – 3 meter for under seat
One min. 8 gauge ring crimp terminal
for the amplifier ground connection.
Wire ties
Insulating grommet or insulating tube
X-program amplifiers for vehicles are manufactured
in accordance with the EU directive EEC 95/54 (72/
245/EEC) and are marked with the approval number.
They are also marked in accordance with the WEEEdirective 2002/96/EC.
The products are also produced in accordance with
the EU RoHS directive 2002/95/EC.
High current draw
The X-D11 is a mono amplifier with high power output.
The current draw is also high so you must make sure
that your vehicles power system (battery and alternator)
can provide all the power you need. If you have a bad
battery or alternator in can result in a poor sound or
even worse, a broken battery or alternator.
Both the positive wire and the ground wire must have
the same size. To avoid cable fire, be sure not to
oversize the main fuse value for the power wires.
Professional Tip:
Maximum main fuse values for different cable sizes.
6 mm2 (9 AWG) :25 A
10 mm2 (7AWG) :40 A
16 mm (5AWG) :60 A
21 mm2 (4AWG) :100 A
33 mm (2AWG) :150 A 42 mm2 (1AWG) :200 A
Power and Outputs
Power terminal ( +12V)
Connect the fuse holder as close to the vehicle
battery + as possible, using AWG4 = 21 mm2 or
heavier cable. Use ring crimp terminal cable to
connect to battery +. Apply silicon grease to the
fuse to prevent corrosion. Use an ANL fuse holder
like the DLS FH2B with fuse value 100 A if you
use the AWG4 cable. If you load the amplifier
down to 1 ohm you should increase cable size to
AWG2 = 33 mm2, and use 150 A ANL
+ pole
ANL fuse holder
Connect the battery cable to the +12 Volt terminal
on the amplifier.
A cable up to AWG 4 fits directly in the amplifier +
12 V terminal, tighten with the hex screw.
Be sure to use a rubber grommet or a plastic
insulating tube where the cable passes the firewall
or other places when it can easily be jammed.
Use wire ties to secure to existing cables in the engine
Remote terminal ( REM )
For RCA cable signal input:
Connect the radio power antenna lead = remote
turn on/off from the car stereo to the amplifier
remote connection. This turns on the amplifier
whenever the car stereo is turned on.
You can either use the built in remote cable in the
RCA cable itself or use a separate cable.
Sometimes a small disturbance may enter the
amplifier coming from the remote voltage , through
the built in remote wire and into the RCA cable.
Thus we recommend to use a separate remote wire
and run the RCA lead separate from remote wire,
power cables and speaker cables.
You can either use a crimp fork terminal or insert
the cable directly into the amplifier terminal. If there
is no remote voltage available from the stereo, you
must connect to the ignition key through the radio
or any accessories fuse.
For High Level input:
We recommend you to connect the remote wire
as described above. The amplifier will produce soft
on / soft off operation this way. You must set the
Hi level/Low level switch to Low level position in
this case.
In the case that there is no remote voltage available
from the car stereo or you want to simplify the
installation, the amplifier can be turned on/ turned
off by the high level input voltage. This is done
when the Hi level/Low level switch is set to Hi level
position. There is a small disadvantage that this
function gives soft turn off operation but some plop
sound when switching off.
Ground Terminal ( GND )
Connect to a good chassis ground. The ground
connection should be clean, unpainted metal to provide a good electrical connection. Use a wire brush, a
scraper or a piece of an abrasive sheet to clean the
metal. Use a lock washer or two to secure contact.
Protect with silicon grease or by paint applied
Power Light / Protect light
The power light (green ) comes on when
the amplifier is turned on.
The protect light ( red ) comes on when
the amplifier shuts down from
overheating or short circuit.
Use only 30 ampere
ATC blade type fuses.
X-D11 uses four 30
ampere fuses.
Input and controls
Input Level control
Input Wiring
Inputs may be low level from the RCA output of the
car stereo or high level from the car stereo speaker
output.Low level = RCA is to prefer for the best sound
Use either the low level or the high level input, do
not use both at same time.
Low level input
Use a pair of shielded stereo audio cables with RCA
type jack. Most trunk-mount amplifiers need a 20
feet RCA cable ( appr 5 – 6 meters). Most under the
seat installations require 12
feet ( 2 – 3 meters) RCA
cables. Avoid placing the RCA
cable close to speaker cables,
power cables and remote
control cable. Connect to input socket A & B.
High Level Input
Connect left and right speaker wires coming from
the car stereo to the high level input as shown. You
must connect both plus and minus as the inputs are
balanced, connecting plus only gives lower level and
bad sound quality. By changing the polarity of plus
and minus, you can change the phase.
High Input
: A ch.+
: A ch.: B ch.: Bch.+
Hi level input plug on amp.
Automatic turn on when using high level input.
With the Hi/Low input swich set to Hi, the amplifier turns
on automatically on high input. You dont need to connect
a separate remote wire from your head unit.
When using High Level input:
Set the switch to position ”Hi / Level”
When using Low level input:
Set the switch to position ”Low / Level”
If the switch is set to wrong
position, the amplifier still
Hi / Level
works, but the risk for
disturbances or distortion
Low / Level
The input level control, 5V – 0,15 V,
matches the output of your radio to the
input of the amplifier. After installation
is complete, make sure the input of the
amplifier is turned down all the way (
counter-clockwise at 5V ). Play a tape
or CD, make sure all bass or treble
settings or equalizer are flat, and turn
the volume of the radio up until you
just start to hear distortion. Turn the
volume control down just a bit. On the
amplifier increase the input level control
( clockwise or to the right ) until you just
start to hear distortion, then back the
level control just a bit. Now your radio
and amplifier levels are matched.
0,15 V
Subsonic filter
The Subsonic filter blocks the very Subsonic
deepest frequencies from reaching the
subwoofers. It has a variable frequency
from 15 to 50 Hz. A typical setting is
15Hz 50Hz
25-30 Hz.
Low Pass Filter
The LPF ( low pass filter ) allow low
frequencies only and blocks higher
frequencies. A typical setting is 60 – 80
Hz. Choose the setting that sounds best
in your car.
15Hz 150Hz
Phase control
The phase control can be set
continuously from 0 - 180 degrees. This
is very useful when you want to adjust
the bass sound for best front stage image.
Start on 0 and turn the control slowly
clockwise until you experience the bass
sound coming from the front.
You may have to change the polarity of
the speaker connection to get the best
Bass boost control on X-D11
Bass boost control is used to set
the bass volume. You can select the
amplification between 0 dB and +18
dB at a 45 Hz center frequency.
This function is used to compensate
for the bass box function and to adjust
for your own taste of bass. Set level
control at 0 dB if you want it to be
Remote Bass boost control
You can fine tune your bass level
from the front of your car. Connect
the external bass level control box to
the remote socket on the rear panel.
0 dB
18 dB
Bass Level
Single amplifier system
Master / Slave switch
must be set to Master
To input of
additional amps.
From low level
output of head unit
Connection of DC-input and Remote level control,
see page 7.
Before you finish the installation, you should do the
following tests to make sure the wiring is correct
and everything is operating properly.
Reconnect Battery
When wiring is complete,
reconnect the battery
negative terminal.
Test power wiring
Turn on the head unit but do not turn up the
volume. The amplifier power light should
come on. If not, check the remote and +12
volt wires. Also check the ground
Turn up the head units volume slightly. All
speakers should operate. if not, check
wiring connections at amplifier and
Minimum speaker load is one (1) ohm. You can
connect four 4 ohm subwoofers or two 2 ohm
subwoofers to the amplifier. Loads or speaker
impedances less than 1 ohm could result in poor
sound quality and/or damage to amplifier.
Filter settings
15Hz 50Hz
15Hz 150Hz
The Subsonic filter at 25-30 Hz and the LPF filter
setting at 60-80 Hz.
RCA Output
Use RCA Outputs to
connect additional
Bridging two amplifiers
Master slave selector & Data link
Connecting two X-D11 in bridge mode will double
the output power. Minimum speaker load is then 2
ohms. The output power with a 4 ohm load is 1500
Watts, and with 2 ohm load 2000 Watts. The RCA
signal must be connected only to the amplifer set
to run as ”Master”.
You can connect t two X-D11 in
bridge mode.
One of the amplifiers is ”Master”
that controls the signal to the
second amplifier that should be
used in ”Slave” position. The signal is fed through the Data link
connector. Connect the
amplifiers as in the drawings
- The filters as well as the level control is only
working on the ”Master” amplifier.
- Bridging two amplifiers can be done only
between amplifiers of the same model.
Modular 4-pole cable to connect
between Data Link sockets
From line output
of head unit
Bridged switch:
Master position
Speaker impedance: 4 ohm/2 ohm
Bridged switch:
Slave position
Connection of DC-input (to both amplifiers) and Remote sub level
control (to Master amplifier).
To Remote on
head unit
Remote bass
boost control.
Distribution block
Power Cap
Professional Tip:
Professional Tip:
All speakers in a car audio system should be
connected in phase (the same polarity). All speaker cones must move in the same direction. Out of
phase speakers will cause a lack of bass, and a
poor stereo soundstage.
Do this:
Rewire the power supply (12 V) to source
unit direct from battery.
Rewire ground wire from source unit to
clean position on chassis.
Check all power connections to ensure that
they are clean and tight.
Check quality of system ground connection.
Install a Power Cap capacitor. This can be
helpful against most noise problems.
Do this:
Ensure that all equipment has a common
ground point.
Check quality of earth strap connection from
battery negative terminal to chassis.
Disconnect signal cables from amplifier to
see if noise disappears. If so the leads are
picking up noise. Test this by laying a new
cable over the seats and reconnecting to the
amplifier. If the noise does not return, reroute original cable away from source of
If noise remains regardless of cable position,
try to use so called Quasi-balanced signal
cables. DLS PRO or ULTIMATE cables are
Professional Tip:
Installing in trunk
When installing the amplifier in the trunk, run the
power wires along the same path as the other
vehicle wiring. Many cars have insulated channels
for wiring. you will have to remove the door sill trim
and the carpet.
Checking polarity:
Hold the - connection of the speaker wire to the terminal of a 1,5 Volt flashlight battery. Tap the +
wire on to the + terminal of the battery, and observe
the movement of the cone. The cone should move
outwards when the wire touches the battery, and
inwards when the battery is removed. If it is the
other way around, the speaker has been connected
backwards and it must be removed and connected
If your system also has a subwoofer connected
through a passive 6 or 12 dB crossover, try to
connect this with various polarity and judge what
sounds best. The phase shift in passive crossovers
sometimes makes it necessary to change polarity.
1,5 Volt
Professional Tip:
Securing wires
Use wire ties to bundle together when possible.
(But never bundle speaker wires or signal cables
together with power wires.
Professional Tip:
1. Strip 1/4 inch (6 mm) of insulation from the wire.
2. Insert into connector
3. Crimp tightly
Professional Tip:
Speaker and power wires
Do not run speaker and power wires next to each
other. Power wires can generate a ”siren” sound in
the speakers. Runs speaker and power wires on
opposite sides of the car.
DLS Svenska AB - 2008-08-25
Crimp connections
Purchase crimp connectors and crimping tool.
Connectors are color coded.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF