ULTRA COMPACT, LOW RIPPLE, HIGH VOLTAGE

ULTRA COMPACT, LOW RIPPLE, HIGH VOLTAGE
TA / TC Series
ÜBERSCHRIFT
1kV
– 2kV, 1.5W
PRODUKTEIGENSCHAFT
ULTRA
COMPACT, LOW RIPPLE
SCHLAGWORTARTIG
HIGH VOLTAGE POWER SUPPLIES FOR PMT
FEATURES
• Ultra-compact, PCB mountable
• Low ripple, 5mVp-p(1kV output type)
• Low Noise due to metal shielding
• Well-regulated, high performance
• External potentiometer or external control voltage
programming
• Arc and continuous short circuit protection
• NRTL(UL1950), TÜV, CE approved
SUMMARY
TA and TC Series are miniaturized, well regulated high
voltage power supplies suitable for photomultiplier.
They feature exceptionally low noise, external
potentiometer or voltage control and fully protection
against arc and continuous output short circuit.
Output voltage
(kVdc)
0 to 1
0 to 1.5
0 to 2
Output current
(mA)
1.5
1
0.7
Model(*Specify “12” for 12Vdc, “15” for 15Vdc input.)
Negative polarity output
Positive polarity output
TA-1P-*
TA-1N-*
TC-1P-*
TC-1N-*
TA-1.5P-*
TA-1.5N-*
TC-1.5P-*
TC-1.5N-*
TA-2P-*
TA-2N-*
TC-2P-*
TC-2N-*
Ripple
(mVp-p)
5
7
10
Output voltage range for this output current is 50% to 100% of maximum output voltage.
Output current must be derated linearly when operating at levels below 50% of the output voltage capability.
SPECIFICATIONS
Input voltage/current
+12Vdc ±1Vdc 230mA Typ
+15Vdc ±1Vdc 180mA Typ
Output control
By external 5kΩ potentiometer or external control
voltage(Vcon-in) 0 to 6Vdc(Input impedance 0 30kΩ)
Regulation
Line : ±0.02% of max voltage for Vin ±1V
Load : 0.02% of max voltage for full load change
Stability
0.02%/Hr 0.05%/8Hr
Temperature coefficient 0.007%/°C
Protection
Overload, arc and continuous output short circuit
Temperature range
Operating : -10°C to +50°C
Storage : -25°C to +85°C
Weight
60g approx
OPTIONS
LS : remote HV ON/OFF
Enable to HV ON/OFF with contact signal.
When open collector,
ON
0.3V(Low)
OFF
2V(High)
Add LS to the model number.
i.e. : TA-1P-12LS, TC-1.5N-15LS
Note : • Specifications are at the maximum rated output after ½Hr warm-up.
TC
30.0
16.0
Ø1
0.5
7.0
2.0
BOTTOM
VIEW
2.54±0.1
5.08±0.3
7.6±0.3 7.6±0.2
35.5
25.4±0.3
35.5
4.0
7-0.6 =4MIN
0.5
BOTTOM
VIEW
16.2
44.0
TA
5
MIN
DIMENSIONS mm
5.08±0.1
2 × CASE PIN
40.6±0.3
50.8
© 2012 hivolt.de - Änderungen und Irrtum vorbehalten / Subject to change without notice, errors expected.
hivolt.de GmbH & Co. KG
Geb. 2
D-22419 Hamburg
Tarpen 40
Germany
+49 40 537122-0
+49 40 537122-99
TA_TC 11/2012 Page 1 of 2
info@hivolt.de
www.hivolt.de
TA / TC Series
ÜBERSCHRIFT
PRODUKTEIGENSCHAFT
SCHLAGWORTARTIG
CONNECTION DIAGRAM
TA
Vcon-in
0 to 6Vdc VR
-or- 5kΩ
R1
TC
HV output
Vin
+12Vdc ±1Vdc
or
+15Vdc ±1Vdc
R2
Vcon-in
0 to 6Vdc VR
-or- 5kΩ
LOAD
CASE PIN
Vref 6.2V
R1
R2
HV-GND
(OPTION)LS
HV output
Vin
+12Vdc ±1Vdc
or
+15Vdc ±1Vdc
LOAD
CASE
Vref 6.2V
HV-GND
(OPTION)LS
Short : HV ON
Open : HV OFF
Short : HV ON
Open : HV OFF
1. PIN
,
are internally connected (isolated from CASE).
2. CASE PIN should be always connected to ground.
3. Input impedance of Pin
is greater than 30kΩ
4. External potentiometer of T.C 100ppm/°C, PC ¼W is recommended.
1. PIN
,
and CASE are internally connected.
2. Input impedance of Pin
is greater than 30kΩ
4. External potentiometer of T.C 100ppm/°C, PC
¼W is recommended.
CHARACTERISTICS OF
OUTPUT VOLTAGE SETTING
Output voltage
100%
linearity ±2% F.S
(kV)
Vcon-in
R1
R2
0 1
0
5kΩ
2
3 4
2.5kΩ
2.5kΩ
5
6V
5kΩ
0
INPUT CURRENT
mA
230mA
Input Current
200
• It is TYP value in 12V input type.
• The 15V input type makes the current
value to be 80%.
R
2R
100
70mA
No Load
0
20%
40%
60%
80%
R=
Vo max
Io max
100%
Output Voltage
© 2012 hivolt.de - Änderungen und Irrtum vorbehalten / Subject to change without notice, errors expected.
hivolt.de GmbH & Co. KG
Geb. 2
D-22419 Hamburg
Tarpen 40
Germany
+49 40 537122-0
+49 40 537122-99
TA_TC 11/2012 Page 2 of 2
info@hivolt.de
www.hivolt.de
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising