X10SRL-F
X10SRL-F
USER’S MANUAL
Revision 1.1
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment to an outlet on a circuit different from that to which the receiver
is connected.
•Consult the authorized dealer or an experienced radio/TV technician for help.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to the
State of California to cause birth defects and other reproductive harm.
Manual Revision 1.1
Release Date: January 14, 2015
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2015 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
Preface
Preface
This manual is written for system integrators, IT professionals, and
knowledgeable end users. It provides information for the installation and use of the
X10SRL-F motherboard.
About This Motherboard
The
X10SRL-F supports a single Intel® E5-2600/1600 Series processor in
an LGA2011 R3 socket. With the Intel® C612 Express chipset built in, the X10SRLF motherboard supports Intel® Server Platform Services (Intel SPS), offering great
system enhancement to high performance storage platforms. Please refer to our
website (http://www.supermicro.com/products/) for processor and memory support
updates. This product is intended to be installed and serviced by professional
technicians.
Manual Organization
Chapter 1 describes the features, specifications and performance of the motherboard, and provides detailed information on the Intel® C612 Express chipset.
Chapter 2 provides hardware installation instructions. Read this chapter when installing the processor, memory modules and other hardware components into the
system. If you encounter any problems, see Chapter 3, which describes troubleshooting procedures for video, memory and system setup stored in the CMOS.
Chapter 4 includes an introduction to the BIOS, and provides detailed information
on running the CMOS Setup utility.
Appendix A provides BIOS Error Beep Codes.
Appendix B lists software program installation instructions.
Appendix C contains UEFI BIOS Recovery instructions.
Appendix D contains Dual Boot Block instructions.
iii
X10SRL-F User’s Manual
Conventions Used in the Manual:
Special attention should be given to the following symbols for proper system installation:
Warning: Critical information given to prevent damage to the components or injury
to yourself.
Note: Additional Information provided for correct system setup.
iv
Contacting Supermicro
Contacting Supermicro
Headquarters
Address:
Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel:
+1 (408) 503-8000
Fax:
+1 (408) 503-8008
Email:
marketing@supermicro.com (General Information)
support@supermicro.com (Technical Support)
Web Site:
www.supermicro.com
Europe
Address:
Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel:
+31 (0) 73-6400390
Fax:
+31 (0) 73-6416525
Email:
sales@supermicro.nl (General Information)
support@supermicro.nl (Technical Support)
rma@supermicro.nl (Customer Support)
Web Site:
www.supermicro.nl
Asia-Pacific
Address:
Super Micro Computer, Inc.
3F, No. 150, Jian 1st Rd.
Zhonghe Dist., New Taipei City 235
Taiwan (R.O.C)
Tel:
+886-(2) 8226-3990
Fax:
+886-(2) 8226-3992
Email:
support@supermicro.com.tw
Web Site:
www.supermicro.com.tw
v
X10SRL-F User’s Manual
Table of Contents
Preface
About This Motherboard................................................................................................. iii
Manual Organization...................................................................................................... iii
Conventions Used in the Manual:..................................................................................iv
Contacting Supermicro....................................................................................................v
Chapter 1 Introduction
1-1Overview.......................................................................................................... 1-1
Checklist........................................................................................................... 1-1
Motherboard Features...................................................................................... 1-6
1-2
Chipset Overview ............................................................................................ 1-9
Intel C612 Express Chipset Features.............................................................. 1-9
1-3 Special Features............................................................................................ 1-10
Recovery from AC Power Loss...................................................................... 1-10
1-4 PC Health Monitoring..................................................................................... 1-10
Environmental Temperature Control.............................................................. 1-10
System Resource Alert.................................................................................. 1-10
1-5 ACPI Features.................................................................................................1-11
Slow Blinking LED for Suspend-State Indicator.............................................1-11
1-6 Power Supply..................................................................................................1-11
1-7 Super I/O........................................................................................................ 1-12
Chapter 2 Installation
2-1
Standardized Warning Statements.................................................................. 2-1
Battery Handling............................................................................................... 2-1
Product Disposal.............................................................................................. 2-3
2-2 Static-Sensitive Devices................................................................................... 2-4
Precautions...................................................................................................... 2-4
Unpacking........................................................................................................ 2-4
2-3 Motherboard Installation................................................................................... 2-5
Tools Needed................................................................................................... 2-5
Location of Mounting Holes............................................................................. 2-5
Installing the Motherboard............................................................................... 2-6
2-4 Processor and Heatsink Installation................................................................ 2-7
Installing the LGA2011 Processor .................................................................. 2-7
Installing a Passive CPU Heatsink.................................................................2-11
Removing the Heatsink.................................................................................. 2-12
2-5 Installing DDR4 Memory................................................................................ 2-13
vi
Table of Contents
DIMM Installation........................................................................................... 2-13
Removing Memory Modules.......................................................................... 2-14
Memory Support............................................................................................. 2-14
Memory Population Guidelines...................................................................... 2-14
2-6
Connectors/IO Ports....................................................................................... 2-17
Backplane I/O Panel...................................................................................... 2-17
Universal Serial Bus (USB)....................................................................... 2-18
Ethernet Ports........................................................................................... 2-19
Serial Ports (COM1/COM2)...................................................................... 2-19
Unit Identifier Switch/UID LED Indicator................................................... 2-20
VGA Port................................................................................................... 2-20
Front Control Panel........................................................................................ 2-21
Front Control Panel Pin Definitions............................................................... 2-22
NMI Button................................................................................................ 2-22
Power LED ............................................................................................... 2-22
HDD LED................................................................................................... 2-23
NIC1/NIC2 LEDs....................................................................................... 2-23
Overheat (OH)/Fan Fail/PWR Fail/UID LED............................................. 2-24
Power Fail LED......................................................................................... 2-24
Reset Button ............................................................................................ 2-25
Power Button ............................................................................................ 2-25
2-7 Connecting Cables......................................................................................... 2-26
ATX Main PWR & CPU PWR Connectors (J24 & JPWR1)...................... 2-26
Fan Headers (Fan 1-Fan 5 & Fan A )....................................................... 2-27
Chassis Intrusion (JL1) ............................................................................ 2-27
Internal Speaker/Buzzer (SP1)................................................................. 2-28
Overheat (OH)/Fan Fail............................................................................. 2-28
DOM PWR Connector (JSD1)................................................................... 2-29
Standby Power.......................................................................................... 2-29
T-SGPIO 1/2/3 Headers............................................................................ 2-30
Power SMB (I2C) Connector..................................................................... 2-30
TPM Header/Port 80 Header.................................................................... 2-31
Video Connector........................................................................................ 2-31
2-8
Jumper Settings............................................................................................. 2-32
Explanation of Jumpers................................................................................. 2-32
LAN1/LAN2 Enable/Disable...................................................................... 2-32
CMOS Clear (JBT1).................................................................................. 2-33
PCI-E Slot SMB Enable (I2C1/I2C2).......................................................... 2-33
vii
X10SRL-F User’s Manual
Manufacture Mode Select......................................................................... 2-34
VGA Enable............................................................................................... 2-34
Watch Dog Enable/Disable....................................................................... 2-35
2-9 Onboard Indicators......................................................................................... 2-36
LAN 1/LAN 2 LEDs................................................................................... 2-36
IPMI Dedicated LAN LEDs........................................................................ 2-36
Onboard Power LED (LE2) ...................................................................... 2-37
BMC Heartbeat LED (LEDM1).................................................................. 2-37
2-10 SATA Connections.......................................................................................... 2-38
SATA Connections..................................................................................... 2-38
Chapter 3 Troubleshooting
3-1 Troubleshooting Procedures............................................................................ 3-1
Before Power On............................................................................................. 3-1
No Power......................................................................................................... 3-1
No Video.......................................................................................................... 3-2
Memory Errors ................................................................................................ 3-2
Losing the System’s Setup Configuration........................................................ 3-2
3-2
Technical Support Procedures......................................................................... 3-3
3-3
Frequently Asked Questions............................................................................ 3-4
3-4
Battery Removal and Installation..................................................................... 3-5
Battery Removal............................................................................................... 3-5
Proper Battery Disposal................................................................................... 3-5
Battery Installation............................................................................................ 3-5
3-5
Returning Merchandise for Service................................................................. 3-6
Chapter 4 BIOS
4-1 Introduction....................................................................................................... 4-1
Starting BIOS Setup Utility............................................................................... 4-1
How To Change the Configuration Data.......................................................... 4-1
How to Start the Setup Utility.......................................................................... 4-2
4-2 Main Setup....................................................................................................... 4-2
The following Main menu items will be displayed:...................................... 4-2
System Date/System Time ......................................................................... 4-3
Supermicro X10SRL-F................................................................................ 4-3
BIOS Version: This item displays the version of the BIOS ROM used in the
system......................................................................................................... 4-3
Build Date: This item displays the date when the version of the BIOS ROM
used in the system was built. .................................................................... 4-3
viii
Table of Contents
Memory Information.................................................................................... 4-3
Total Memory: This item displays the total size of memory available in the
system......................................................................................................... 4-3
Memory Speed: This item displays the default speed of the memory
modules installed in the system.................................................................. 4-3
4-3 Advanced Setup Configurations...................................................................... 4-4
Boot Feature.................................................................................................. 4-4
Quiet Boot................................................................................................... 4-4
AddOn ROM Display Mode......................................................................... 4-4
Bootup Num-Lock........................................................................................ 4-4
Wait For 'F1' If Error.................................................................................... 4-5
INT19 (Interrupt 19) Trap Response........................................................... 4-5
Re-try Boot.................................................................................................. 4-5
Power Configuration......................................................................................... 4-5
DeepSx Power Policies............................................................................... 4-5
Watch Dog Function.................................................................................... 4-5
Power Button Function................................................................................ 4-5
Restore on AC Power Loss......................................................................... 4-6
CPU Configuration........................................................................................ 4-6
CPU Configuration...................................................................................... 4-6
Clock Spread Spectrum.............................................................................. 4-6
Hyper-Threading (ALL)................................................................................ 4-7
Cores Enabled............................................................................................. 4-7
Execute Disable Bit (Available if supported by the OS & the CPU)........... 4-7
PPIN Control............................................................................................... 4-7
Hardware Prefetcher (Available when supported by the CPU).................. 4-7
Adjacent Cache Line Prefetch (Available when supported by the CPU).... 4-7
DCU Streamer Prefetcher (Available when supported by the CPU).......... 4-7
DCU IP Prefetcher...................................................................................... 4-8
DCU (Data Cache Unit) Mode.................................................................... 4-8
Direct Cache Access (DCA)........................................................................ 4-8
DCA Prefetch Delay.................................................................................... 4-8
X2APIC (Extended Advanced Programmable Interrupt Controller)............ 4-8
AES-NI......................................................................................................... 4-8
Intel Virtualization Technology..................................................................... 4-8
Advanced Power Management Configuration.............................................. 4-9
Chipset Configuration................................................................................. 4-12
North Bridge................................................................................................ 4-12
ix
X10SRL-F User’s Manual
IIO Configuration......................................................................................... 4-12
 Intel VT for Directed I/O (VT-d)................................................................. 4-13
QPI (Quick Path Interconnect) Configuration............................................. 4-14
South Bridge................................................................................................ 4-18
Legacy USB Support................................................................................. 4-18
XHCI Hand-Off.......................................................................................... 4-18
EHCI Hand-Off.......................................................................................... 4-18
USB Mass Storage Driver Support........................................................... 4-18
Port 60/64 Emulation................................................................................. 4-18
USB 3.0 Support....................................................................................... 4-18
EHCI1........................................................................................................ 4-18
EHCI2........................................................................................................ 4-19
XHCI Pre-Boot Driver................................................................................ 4-19
XHCI Idle L1.............................................................................................. 4-19
PCH DMI ASPM........................................................................................ 4-19
SATA Configuration..................................................................................... 4-19
SATA Controller......................................................................................... 4-19
Configure SATA as.................................................................................... 4-19
*If the item above "Configure SATA as" is set to IDE, the following items
will display:................................................................................................ 4-20
*If the item above "Configure SATA as" is set to RAID, the following items
will display:................................................................................................ 4-21
sSATA Configuration.................................................................................... 4-22
sSATA Controller....................................................................................... 4-22
Configure sSATA as.................................................................................. 4-22
*If the item above "Configure sSATA as" is set to IDE, the following items
will display:................................................................................................ 4-23
*If the item above "Configure sSATA as" is set to RAID, the following items
will display:................................................................................................ 4-23
Server ME (Management Engine) Configuration........................................ 4-24
PCIe/PCI/PnP Configuration....................................................................... 4-25
The following PCI information will be displayed:...................................... 4-25
VGA Palette Snoop................................................................................... 4-25
PCI AER (Advanced Error-Reporting) Support......................................... 4-25
Above 4G Decoding (Available if the system supports 64-bit PCI decoding).
4-25
SR-IOV Support (Available if the system supports Single-Root
Virtualization)............................................................................................. 4-25
Maximum Payload..................................................................................... 4-25
Maximum Read Request........................................................................... 4-25
x
Table of Contents
ASPM Support........................................................................................... 4-25
MMIOHBase.............................................................................................. 4-26
MMIO High Size........................................................................................ 4-26
PCH SLOT1 PCI-E 2.0 x4 (in x8) OPPROM, CPU SLOT2 PCI-E 3.0 x4 (in
x8) OPPROM, CPU SLOT3 PCI-E 3.0 x8 OPPROM, CPU SLOT4 PCI-E
3.0 x8 (in x16) OPPROM, CPU SLOT5 PCI-E 3.0 x8 OPPROM, CPU
SLOT6 PCI-E 3.0 x16 OPPROM, CPU SLOT7 PCI-E 3.0 x8 OPPROM, ....
4-26
Onboard LAN Option ROM Type.............................................................. 4-26
Onboard LAN1 Option ROM/Onboard LAN2 Option ROM....................... 4-26
Onboard Video Option ROM..................................................................... 4-26
VGA Priority............................................................................................... 4-26
Network Stack........................................................................................... 4-26
Super IO Configuration .............................................................................. 4-27
Serial Port 1 Configuration/Serial Port 2 Configuration......................... 4-27
Serial Port 1/Serial Port 2......................................................................... 4-27
Device Settings......................................................................................... 4-27
Change Port 1 Settings/Change Port 2 Settings...................................... 4-27
Serial Port 2 Attribute................................................................................ 4-27
Serial Port Console Redirection.................................................................. 4-27
COM 1 Console Redirection..................................................................... 4-27
COM1 Console Redirection Settings.......................................................... 4-28
SOL/COM2................................................................................................ 4-29
SOL/COM2 Console Redirection.............................................................. 4-29
SOL/COM2 Console Redirection Settings.................................................. 4-29
Serial Port for Out-of-Band Management/Windows Emergency Management
Services (EMS)......................................................................................... 4-31
EMS (Emergency Management Services) Console Redirection.............. 4-31
EMS Console Redirection Settings............................................................. 4-31
Trusted Computing (Available when a TPM device is installed and detected
by the BIOS).................................................................................................. 4-32
Configuration............................................................................................. 4-32
Security Device Support............................................................................ 4-32
TPM State................................................................................................. 4-32
Pending Operation.................................................................................... 4-32
Current Status Information........................................................................ 4-32
ACPI Settings ............................................................................................. 4-33
WHEA Support.......................................................................................... 4-33
High Precision Timer................................................................................. 4-33
NUMA........................................................................................................ 4-33
xi
X10SRL-F User’s Manual
4-4 Event Logs.....................................................................................................4-34
Change SMBIOS Event Log Settings........................................................ 4-34
Enabling/Disabling Options....................................................................... 4-34
SMBIOS Event Log................................................................................... 4-34
Runtime Error Logging Support................................................................ 4-34
Memory Corrected Error Enabling (Available when the item above-Runtime
Error Logging Support is set to Enable)................................................... 4-34
PCI-Ex (PCI-Express) Error Enable.......................................................... 4-34
Memory Correctable Error Threshold........................................................ 4-35
Erasing Settings........................................................................................ 4-35
Erase Event Log........................................................................................ 4-35
When Log is Full....................................................................................... 4-35
SMBIOS Event Log Standard Settings..................................................... 4-35
Log System Boot Event............................................................................ 4-35
MECI (Multiple Event Count Increment)................................................... 4-35
METW (Multiple Event Count Time Window)............................................ 4-35
View System Event Log............................................................................ 4-35
4-5 IPMI................................................................................................................ 4-36
IPMI Firmware Revision............................................................................ 4-36
IPMI Status................................................................................................ 4-36
System Event Log...................................................................................... 4-36
Enabling/Disabling Options....................................................................... 4-36
SEL Components...................................................................................... 4-36
Erasing Settings........................................................................................ 4-36
Erase SEL................................................................................................. 4-36
When SEL is Full....................................................................................... 4-37
BMC Network Configuration....................................................................... 4-37
IPMI LAN Selection................................................................................... 4-37
IPMI Network Link Status.......................................................................... 4-37
Update IPMI LAN Configuration................................................................ 4-37
Configuration Address Source.................................................................. 4-37
4-6Security.......................................................................................................... 4-39
Password Check....................................................................................... 4-39
Administrator Password............................................................................ 4-39
4-7Boot................................................................................................................ 4-40
Setup Prompt Timeout.............................................................................. 4-40
Boot Mode Select...................................................................................... 4-40
Fixed Boot Order Priorities........................................................................ 4-40
Delete Boot Option................................................................................. 4-41
xii
Table of Contents
Hard Disk Drive BBS Priorities.............................................................. 4-41
Network Drive BBS Priorities................................................................. 4-41
UEFI Application Boot Priorities............................................................. 4-41
4-8 Save & Exit.................................................................................................... 4-42
Discard Changes and Exit ....................................................................... 4-42
Save Changes and Reset......................................................................... 4-42
Save Options............................................................................................. 4-42
Save Changes........................................................................................... 4-42
Discard Changes....................................................................................... 4-42
Restore Defaults........................................................................................ 4-42
Save As User Defaults.............................................................................. 4-43
Restore User Defaults............................................................................... 4-43
Boot Override............................................................................................ 4-43
Appendix A BIOS Error Beep Codes
A-1 BIOS Error Beep Codes..................................................................................A-1
Appendix B Software Installation Instructions
B-1 Installing Software Programs...........................................................................B-1
B-2 Installing SuperDoctor® 5................................................................................B-2
Appendix C UEFI BIOS Recovery Instructions
C-1 An Overview to the UEFI BIOS.......................................................................C-1
C-2 How to Recover the UEFI BIOS Image ..........................................................C-1
C-3 To Recover the Main BIOS Block Using a USB-Attached Device..................C-1
Appendix D Dual Boot Block on Grantley Platforms
Overview......................................................................................................................D-1
Before Startup.............................................................................................................D-1
When to Use Dual Boot Block....................................................................................D-1
How to Use Dual Boot Block......................................................................................D-1
D-1
IPMI GUI Browser............................................................................................D-2
D-2
IPMI Command Sets........................................................................................D-7
User Approach.............................................................................................................D-9
xiii
X10SRL-F User’s Manual
Notes
xiv
Chapter 1: Introduction
Chapter 1
Introduction
1-1Overview
Checklist
Congratulations on purchasing your computer motherboard from an acknowledged
leader in the industry. Supermicro boards are designed with the utmost attention to
detail to provide you with the highest standards in quality and performance.
Please check that the following items have all been included with your motherboard.
If anything listed here is damaged or missing, contact your retailer.
The following items are included in the retail box:
•One (1) Supermicro Motherboard
•Six (6) SATA cables
•One (1) I/O shield
•One (1) Quick Reference Guide
Note: For your system to work properly, please follow the links below to
download all necessary drivers/utilities and the user's manual for your
motherboard.
Supermciro product manuals: http://www.supermicro.com/support/manuals/
Product Drivers and utilities: ftp://ftp.supermicro.com/
If you have any questions, please contact our support team at support@supermicro.
com.
1-1
X10SRL-F User’s Manual
X10SRL-F Motherboard Image
Note: All graphics shown in this manual were based upon the latest PCB Revision
available at the time of publishing of the manual. Your motherboard or components
may or may not look exactly the same as the graphics shown in this manual.
1-2
Chapter 1: Introduction
X10SRL-F Motherboard Layout
UID LED - LE1
UID - SW
COM1
VGA
USB2/3(3.0)
BMC
COM2
LAN
CTRL
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
LAN1
LAN2
JPL2
LEDM1
CPU
1
+
BT1
SP1
USB4/5
USB6/7
1
USB8/9
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
JPME2
DESIGNED IN USA
BAR CODE
Intel PCH
BIOS LICENSE
IPMI CODE
JPI2C1
JWD1
MAC CODE
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JL1
LE2
USB11(3.0)
JD1
JPWR1
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
JSTBY1
5V STBY1
J24
I_SATA4
I-SATA5 JSD2
S-SATA3
S-SATA2
JSD1
S-SATA1 S-SATA0
FANA
JBR1
JTPM1
Rev: 1.01
JF1
FAN4 FAN3
FAN2 FAN1
Notes:
•See Chapter 2 for detailed information on jumpers, I/O ports and JF1 front
panel connections.
•"
" indicates the location of "Pin 1".
•Jumpers not indicated are for testing only.
•When the onboard Power LED Indicator (LE2) is on, system power is on.
Unplug the power cable before installing or removing any components.
1-3
X10SRL-F User’s Manual
X10SRL-F Quick Reference
UID LED - LE1
UID - SW
COM1
VGA
USB2/3(3.0)
BMC
LAN1
LAN2
JPL2
COM2
LEDM1
LAN
CTRL
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
CPU
1
+
BT1
SP1
USB4/5
USB6/7
1
USB8/9
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
JPME2
JBR1
JTPM1
Rev: 1.01
BAR CODE
BIOS LICENSE
IPMI CODE
JPI2C1
JWD1
MAC CODE
JL1
I-SATA3 I-SATA2 I-SATA1 I-SATA0
LE2
USB11(3.0)
JD1
JPWR1
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
JSTBY1
5V STBY1
J24
I_SATA4
S-SATA1 S-SATA0
FANA
I-SATA5 JSD2
S-SATA3
S-SATA2
JSD1
DESIGNED IN USA
Intel PCH
JF1
FAN4 FAN3
FAN2 FAN1
X10SRL-F Jumpers
Jumper
Description
Default
JBR1
BIOS Recovery
Pins 1-2 (Normal)
JBT1
CMOS Clear
See Chapter 2
JI C1/JI C2
SMB to PCI-E Slots
Pins 2-3 (Disabled)
JPB1
BMC Enable/Disable
Pins 1-2 (Enabled)
JPG1
VGA Enable
Pins 1-2 (Enabled)
JPL1/JPL2
LAN1/LAN2 Enable
Pins 1-2 (Enabled)
JPME2
Manufacture Mode Select
Pins 1-2 (Normal)
JWD1
Watch Dog Enable
Pins 1-2 (Reset)
2
2
1-4
Chapter 1: Introduction
X10SRL-F Headers/Connectors
Connector
Description
Battery (BT1)
Onboard Battery
COM1/COM2
COM1 (Port)/COM2 (Header)
Fan1 - Fan5, FanA
System/CPU Fan Headers
J24
24-pin Main ATX Power Connector
JD1
Speaker/Buzzer (Pins 1-3: Power LED, Pins 4-7: Speaker)
JF1
Front Panel Control Header
JIPMB1
4-pin External BMC I2C Header (for an IPMI Card)
JL1
Chassis Intrusion Header
JOH1
Overheat/Fan Fail Indicator
JPI C1
Power SMB (System Management Bus)
JPWR1
8-pin Secondary Power Connector
JSD1/JSD2
SATA DOM (Device_On_Module) Power Connector
JSTBY1
Standby Power Header
JTPM1
Trusted Platform Module/Port 80 Connector
JVR1
PWM SMB Programming (for debugging only)
LAN1/LAN2
Gigabit (RJ45) Ports (LAN1/2)
IPMI_LAN
IPMI_Dedicated LAN
I-SATA 0-9
(Intel PCH) Serial ATA (SATA 3.0) Ports 0-9 (6Gb/sec)
(PCH) Slot 1
PCI-Express 2.0 (x4 in x8 Slot)
(CPU) Slots 2-7
Six (6) PCI-Express 3.0 slots: 2 (x8 in x16), 2 (x8), 1 (x8//x4), 1 (x0//x4)
SP1
Internal Speaker/Buzzer
T-SGPIO 1/2/3
Serial_Link General Purpose I/O Headers 1/2/3 for SATA Connections
UID SW
Unit Indentifier Switch
USB 0/1
Backpanel USB 2.0 Ports 0/1
USB 2/3
Backpanel USB 3.0 Ports 2/3
USB 4/5, 6/7, 8/9
Front Panel Accessible USB 2.0 Headers 4/5, 6/7, 8/9
USB 10, 11 (3.0)
Front Panel Accessible USB 3.0 Ports 10, 11
VGA
Backpanel VGA Port
2
X10SRL-F LED Indicators
LED
Description
State/Color
Status
LE1
UID LED
Blue: On
Unit Identified
LE2
Onbaord PWR LED
Green: On
System Power On
LEDM1
BMC Heartbeat LED
Green: Blinking
BMC Normal
1-5
X10SRL-F User’s Manual
Motherboard Features
CPU
Single Intel ® E5-2600/1600 Series processor in an
LGA2011 R3 socket.
Memory
Eight (8) ECC/Non-ECC DDR4 RDIMM/LRDIMM/UDIMM
at 1333/1600/1866/2133 MHz memory (1 DPC) up to
256GB RDIMM, 512GB LRDIMM, or 64GB UDIMM.
Dual-channel memory
DIMM sizes
RDIMM
1GB, 2 GB, 4GB, 8GB, 16GB, and
32GB
Chipset
Intel® C612 Express
Expansion Slots
One (1) PCI Express 2.0: 1 (x4 in x8)
Six (6) PCI Express 3.0: 2 (x8 in x16), 2 (x8), 1 (x8 or x4),
1 (x0 or x4)
Two (2) RJ-45 rear I/O panel connectors with Link and
Activity LEDs
I/O Devices
SATA Connections
Ten (10) SATA3 ports
•AHCI controller supports six (6)
SATA3 drives compatible with
RAID 0, 1, 5, 10.
SATA 3.0 (6Gb/s)
•sSATA controller supports four
(4) SATA3 drives compatible
with RAID 0, 1, 5, 10.
•RAID array and volume(s) can-
not span across the two (AHCI
and sSATA) controllers.
SATA DOM
Two (2) SATA DOM Ports (SATA 4/5)
USB Devices
Eight (8) USB 2.0 ports ( 2 rear, 6 via headers)
Four (4) USB 3.0 headers for USB 3.0 support (2 rear, 1
Type-A, 1 via header)
Serial (COM) Ports
Two (2) COM Ports (1 header, 1 rear)
Graphics Controller
AST 2400 Graphics Controller
Network
One i210 Dual-Channel Gigabit (100/1000 MB/s)
Ethernet Contoller for LAN 1/LAN 2 ports
1-6
Chapter 1: Introduction
BIOS
128 Mb AMI BIOS® SPI Flash BIOS
Plug and Play (PnP), DMI 2.3, PCI 2.3, ACPI 1.0/2.0/3.0,
USB Keyboard and SMBIOS 2.5
Power Configuration
APM 1.2, APCI 2.3, ACPI 1.0/2.0/3.0/4.0, USB Keyboard,
Plug & Play (PnP) and SMBIOS 2.3
Main Switch Override Mechanism
Power-on mode for AC power recovery
PC Health Monitoring
CPU Monitoring
Onboard voltage monitors for CPU core, +3.3V, +5V,+12V,
+3.3V Stdby, VBAT, Memory, PCH and BMC voltage
CPU 5-phase switching voltage
CPU/System overheat LED and control
CPU Thermal Trip support
Thermal Monitor support
Fan Control
Fan status monitoring with firmware 4-pin fan speed control via IPMI interface
Low noise fan speed control
System Management
PECI (Platform Environment Configuration Interface) 2.0
support
UID (Unit Identification)/Remote UID
System resource alert via SuperDoctor® 5
SuperDoctor® 5, Watch Dog, NMI
Chassis Intrusion header and detection
BIOS flash upgrade utility
Dimensions
ATX form factor: 9.6" x 12" (243.84mm x 304.8mm)
1-7
X10SRL-F User’s Manual
X10SRL-F Block Diagram
0-8
0-7
0-6
0-5
0-4
0-3
0-2
0-1
CPU
1A 1B DMI2 2C/D 2A/B 3C/D 3A/B
PCIe3.0 x8
PCIe3.0 x4
PCI-E PCIe3.0 x4
PCIe3.0 x0//x4 SWITCH
DMI2
5GT/s
SLOT1
RJ45
RJ45
RJ45
LAN3
RTL8211E-VB-CG
DDR3
BMC Boot Flash
BIOS
SPI
PCIe2.0 x4
PCIe2.0 x8
LAN2
Springville
i210AT
LAN1
Springville
i210AT
RGRMII
1/2/3/4
PCIe2.0 x1
6
PCIe2.0 x1
PCH
6.0 Gb/S
5
USB 2.0
PCe2.0 x1
BMC
AST2400
56
12
USB 3.0
13
SPI
LPC
COM1
Connector
COM2
Header
Temp Sensor
EMC1402-1 *2 at diff SMBUS
SPI
TPM HEADER
Debug Card
SLOT5
67
45
23
01
7
USB 2.0
SLOT4
PCIe3.0 x16
PCIe3.0 x8
9
78
56
4
23
01
RMII/NCSI
SPI
VGA CONN
PCIe3.0 x8
PCIe3.0 x8
SLOT7
SATA
PCIe3.0 x8
SLOT6
PCIe3.0 x16
PCIe3.0 x8
USB2.0
PCIe3.0 x8
SLOT2
PCIe3.0 x8
PCIe3.0 x8//x4
USB3.0
SLOT3
DDRIV
1333/1600/2133
DDRIV
1333/1600/2133
VR12.5
5 PHASE
145W
BIOS
HEADER
SYSTEM POWER
FRONT PANEL
FAN SPEED
CTRL
System Block Diagram
Note: This is a general block diagram and may not exactly represent
the features on your motherboard. See the Motherboard Features
pages for the actual specifications of each motherboard.
1-8
Chapter 1: Introduction
1-2 Chipset Overview
The X10SRL-F supports a single Intel® E5-2600/1600 Series Processor in an
LGA2011 R3 socket. Built upon the functionality and the capability of the Intel ®
C612 Express chipset, the motherboard provides substantial enhancement to
system performance and storage capability for high performance platforms in a
sleek package.
The high-speed Direct Media Interface (DMI) featured in the Intel® C612 Express
chipset supports high-speed Direct Media Interface (DMI) for chip-to-chip true
isochronous communication, providing up to 5 GT/s of software-transparent data
transfer rate on each read/write direction. In addition, the X10SRL-F also features
a TCO timer which allows the system to recover from a software/hardware lock
and perform tasks, including Function Disable and Intruder Detect.
Intel® C612 Express Chipset Features
•Direct Media Interface (up 5 GT/s transfer, Full Duplex)
•Dual NAND Interface
•Intel® I/O Virtualization (VT-d) Support
•Intel® Trusted Execution Technology Support
•PCI Express 2.0 Interface (up to 5.0 GT/s)
•SATA Controller (up to 6Gb/sec)
•Advanced Host Controller Interface (AHCI)
1-9
X10SRL-F User’s Manual
1-3 Special Features
Recovery from AC Power Loss
Basic I/O System (BIOS) provides a setting for you to determine how the system will
respond when AC power is lost and then restored to the system. You can choose
for the system to remain powered off, (in which case you must press the power
switch to turn it back on), or for it to automatically return to a power-on state. See
the Advanced BIOS Setup section to change this setting. The default setting is
Last State.
1-4 PC Health Monitoring
This section describes the PC health monitoring features of the board. All have
an onboard System Hardware Monitoring chip that supports PC health monitoring.
An onboard voltage monitor will scan these onboard voltages continuously: CPU
Vcore, 12V, 5V, 5VSB, 3.3V, 3.3VSB, Memory, PCH, BMC and Battery voltages.
Once a voltage becomes unstable, a warning is given, or an error message is sent
to the screen. The user can adjust the voltage thresholds to define the sensitivity
of the voltage monitor.
Environmental Temperature Control
The thermal control sensor monitors the CPU temperature in real time and will turn
on the thermal control fan whenever the CPU temperature exceeds a user-defined
threshold. The overheat circuitry runs independently from the CPU. Once the thermal sensor detects that the CPU temperature is too high, it will automatically turn
on the thermal fans to prevent the CPU from overheating. The onboard chassis
thermal circuitry can monitor the overall system temperature and alert the user when
the chassis temperature is too high.
Note: To avoid possible system overheating, please be sure to provide
adequate airflow to your system.
System Resource Alert
This feature is available when the system is used with SuperDoctor ® 5 in the
Windows and Linux operating systems. SuperDoctor is used to notify the user
of certain system events. For example, you can also configure SuperDoctor to
provide you with warnings when the system temperature, CPU temperatures,
voltages and fan speeds go beyond predefined thresholds.
1-10
Chapter 1: Introduction
1-5 ACPI Features
ACPI stands for Advanced Configuration and Power Interface. The ACPI specification defines a flexible and abstract hardware interface that provides a standard
way to integrate power management features throughout a PC system, including
its hardware, operating system and application software. This enables the system
to automatically turn on and off peripherals such as CD-ROMs, network cards, hard
disk drives and printers.
In addition to enabling operating system-directed power management, ACPI also
provides a generic system event mechanism for Plug and Play, and an operating
system-independent interface for configuration control. ACPI leverages the Plug and
Play BIOS data structures, while providing a processor architecture-independent
implementation that is compatible with Windows 7, Windows 8, and Windows 2008
Operating Systems.
Slow Blinking LED for Suspend-State Indicator
When the CPU goes into a suspend state, the chassis power LED will start to blink
to indicate that the CPU is in suspend mode. When the user presses any key, the
CPU will "wake up", and the LED will automatically stop blinking and remain on.
1-6 Power Supply
As with all computer products, a stable power source is necessary for proper and
reliable operation. It is even more important for processors that have high CPU
clock rates.
This motherboard accommodates 24-pin ATX power supplies. Although most
power supplies generally meet the specifications required by the CPU, some are
inadequate. In addition, the 12V 8-pin power connector located at JPWR1 is also
required to ensure adequate power supply to the system.
Warning: To avoid damaging the power supply or motherboard, please use a power
supply that contains a 24-pin and an 8-pin power connectors. Be sure to connect the
24-pin (J24) and the 8-pin (JPWR1) power connectors on the motherboard to the
power supply. Failure in doing so will void the manufacturer warranty on your power
supply and motherboard.
It is strongly recommended that you use a high quality power supply that meets ATX
power supply Specification 2.02 or above. It must also be SSI compliant. (For more
information, please refer to the web site at http://www.ssiforum.org/). Additionally, in
areas where noisy power transmission is present, you may choose to install a line filter
to shield the computer from noise. It is recommended that you also install a power
surge protector to help avoid problems caused by power surges.
1-11
X10SRL-F User’s Manual
1-7 Super I/O
The Super I/O supports two high-speed, 16550 compatible serial communication
ports (UARTs). Each UART includes a 16-byte send/receive FIFO, a programmable
baud rate generator, complete modem control capability and a processor interrupt
system. Both UARTs provide legacy speed with baud rate of up to 115.2 Kbps
as well as an advanced speed with baud rates of 250 K, 500 K, or 1 Mb/s, which
support higher speed modems.
The Super I/O provides functions that comply with ACPI (Advanced Configuration
and Power Interface), which includes support of legacy and ACPI power management through an SMI or SCI function pin. It also features auto power management
to reduce power consumption.
1-12
Chapter 2: Installation
Chapter 2
Installation
2-1 Standardized Warning Statements
The following statements are industry-standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions or
experience difficulty, contact Supermicro's Technical Support department for assistance. Only certified technicians should attempt to install or configure components.
Read this section in its entirety before installing or configuring components in the
Supermicro chassis.
Battery Handling
Warning!
There is a danger of explosion if the battery is replaced incorrectly. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー
カーが推奨する型、
または同等のものを使用下さい。使用済電池は製造元の指示に従
って処分して下さい。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更
换原有电池。请按制造商的说明处理废旧电池。
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有
電池。請按照製造商的說明指示處理廢棄舊電池。
Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die
Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
2-1
X10SRL-F User’s Manual
Attention
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer
que par une pile de type semblable ou équivalent, recommandée par le fabricant.
Jeter les piles usagées conformément aux instructions du fabricant.
¡Advertencia!
Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Reemplazar la batería exclusivamente con el mismo tipo o el equivalente recomendado por el fabricante. Desechar las baterías gastadas según las instrucciones
del fabricante.
!‫אזהרה‬
‫ יש להחליף‬.‫קיימת סכנת פיצוץ של הסוללה במידה והוחלפה בדרך לא תקינה‬
.‫את הסוללה בסוג התואם מחברת יצרן מומלצת‬
.‫סילוק הסוללות המשומשות יש לבצע לפי הוראות היצרן‬
‫هناك خطر من انفجار في حالة اسحبذال البطارية بطريقة غير صحيحة فعليل‬
‫اسحبذال البطارية‬
‫فقط بنفس النىع أو ما يعادلها مما أوصث به الشرمة المصنعة‬
‫جخلص من البطاريات المسحعملة وفقا لحعليمات الشرمة الصانعة‬
경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일
하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다. 제조사
의 안내에 따라 사용된 배터리를 처리하여 주십시오.
Waarschuwing
Er is ontploffingsgevaar indien de batterij verkeerd vervangen wordt. Vervang de
batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften
afgevoerd te worden.
2-2
Chapter 2: Installation
Product Disposal
Warning!
Ultimate disposal of this product should be handled according to all national laws
and regulations.
製品の廃棄
この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が
あります。
警告
本产品的废弃处理应根据所有国家的法律和规章进行。
警告
本產品的廢棄處理應根據所有國家的法律和規章進行。
Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen
des Landes erfolgen.
¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.
Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des
lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de
l'organisme compétent.
‫סילוק המוצר‬
!‫אזהרה‬
.‫סילוק סופי של מוצר זה חייב להיות בהתאם להנחיות וחוקי המדינה‬
2-3
X10SRL-F User’s Manual
‫عند التخلص النهائي من هذا المنتج ينبغي التعامل معه وفقا لجميع القىانين واللىائح الىطنية‬
경고!
이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.
Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming
met alle nationale wetten en reglementen.
2-2 Static-Sensitive Devices
Electrostatic-Discharge (ESD) can damage electronic com­ponents. To avoid damaging your system board, it is important to handle it very carefully. The following
measures are generally sufficient to protect your equipment from ESD.
Precautions
• Use a grounded wrist strap designed to prevent static discharge.
• Touch a grounded metal object before removing the board from the antistatic
bag.
• Handle the board by its edges only; do not touch its components, peripheral
chips, memory modules or gold contacts.
• When handling chips or modules, avoid touching their pins.
• Put the motherboard and peripherals back into their antistatic bags when not in
use.
• For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and
the motherboard.
• Use only the correct type of onboard CMOS battery. Do not install the onboard
battery upside down to avoid possible explosion.
Unpacking
The motherboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure that the person handling it is static protected.
2-4
Chapter 2: Installation
2-3 Motherboard Installation
All motherboards have standard mounting holes to fit different types of chassis.
Make sure that the locations of all the mounting holes for both motherboard and
chassis match. Although a chassis may have both plastic and metal mounting fasteners, metal ones are highly recommended because they ground the motherboard
to the chassis. Make sure that the metal standoffs click in or are screwed in tightly.
Then use a screwdriver to secure the motherboard onto the motherboard tray.
Tools Needed
Philips Screwdriver
(1)
Standoffs (9)
Only if Needed
Philips Screws (9)
Location of Mounting Holes
UID LED - LE1
UID - SW
COM1
VGA
USB2/3(3.0)
BMC
COM2
LAN
CTRL
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
LAN1
LAN2
JPL2
LEDM1
CPU
1
+
BT1
SP1
USB4/5
USB6/7
1
USB8/9
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
JPME2
JBR1
JTPM1
Rev: 1.01
BAR CODE
I-SATA5 JSD2
IPMI CODE
JPI2C1
JWD1
MAC CODE
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JSTBY1
5V STBY1
JL1
LE2
USB11(3.0)
JD1
J24
I_SATA4
S-SATA1 S-SATA0
JSD1
BIOS LICENSE
JPWR1
S-SATA3
S-SATA2
FANA
DESIGNED IN USA
Intel PCH
JF1
FAN4 FAN3
FAN2 FAN1
Caution: 1) To avoid damaging the motherboard and its components, please do
not use a force greater than 8 lb/inch on each mounting screw during motherboard
installation. 2) Some components are very close to the mounting holes. Please take
precautionary measures to avoid damaging these components when installing the
motherboard to the chassis.
2-5
X10SRL-F User’s Manual
Installing the Motherboard
1. Install the I/O shield into the back of the chassis.
2. Locate the mounting holes on the motherboard. (See the previous page.)
3. Locate the matching mounting holes on the chassis. Align the mounting holes
on the motherboard against the mounting holes on the chassis.
4. Install standoffs in the chassis as needed.
5. Install the motherboard into the chassis carefully to avoid damaging other
motherboard components.
6. Using the Phillips screwdriver, insert a Phillips head #6 screw into a mounting
hole on the motherboard and its matching mounting hole on the chassis.
7. Repeat Step 5 to insert #6 screws into all mounting holes.
8. Make sure that the motherboard is securely placed in the chassis.
Note: Images displayed are for illustration only. Your chassis or components might look different from those shown in this manual.
2-6
Chapter 2: Installation
2-4 Processor and Heatsink Installation
Warning: When handling the processor package, avoid placing direct pressure on the
label area of the fan.
Notes:
•Always connect the power cord last, and always remove it before adding, re-
moving or changing any hardware components. Make sure that you install the
processor into the CPU socket before you install the CPU heatsink.
•If you buy a CPU separately, make sure that you use an Intel-certified multidirectional heatsink only.
•Make sure to install the system board into the chassis before you install the
CPU heatsink.
•When receiving a server board without a processor pre-installed, make sure that
the plastic CPU socket cap is in place and none of the socket pins are bent;
otherwise, contact your retailer immediately.
•Refer to the Supermicro website for updates on CPU support.
Installing the LGA2011 Processor
1. There are two load levers on the LGA2011 socket. To open the socket cover,
first press and release the load lever labeled 'Open 1st'.
2
1
WA
R
NI
OP
EN
NG
WA
R
NI
!
OP
EN
1st
Press down
on Load Lever
labeled 'Open 1st'.
2-7
1st
NG
!
X10SRL-F User’s Manual
2. Press the second load lever labeled 'Close 1st' to release the load plate that
covers the CPU socket from its locking position.
1
Press down on Load
Lever 'Close 1st'
WA
R
2
Pull lever away from
the socket
WA
R
NI
NG
NI
OP
OP
EN
NG
!
EN
1st
!
1st
3. With the lever labeled 'Close 1st' fully retracted, gently push down on the
lever labelled 'Open 1st' to open the load plate. Lift the load plate to open it
completely.
Gently push
down to pop the
load plate open.
1
WA
R
NI
OP
EN
NG
2
!
1st
WA
R
NI
2-8
NG
!
Chapter 2: Installation
4. Using your thumb and the index finger, remove the 'WARNING' plastic cap
from the socket.
WA
R
NIN
G!
5. Using your thumb and index finger, hold the CPU on its edges. Align the CPU
keys, which are semi-circle cutouts, against the socket keys.
Socket Keys
CPU Keys
6. Once they are aligned, carefully lower the CPU straight down into the socket.
(Do not drop the CPU on the socket. Do not move the CPU horizontally or
vertically. Do not rub the CPU against the surface or against any pins of the
socket to avoid damaging the CPU or the socket.)
Warning: You can only install the CPU
inside the socket in one direction. Make
sure that it is properly inserted into the
CPU socket before closing the load
plate. If it doesn't close properly, do not
force it as it may damage your CPU.
Instead, open the load plate again to
make sure that the CPU is aligned
properly.
2-9
X10SRL-F User’s Manual
7. With the CPU inside the socket, inspect the four corners of the CPU to make
sure that the CPU is properly installed.
8. Close the load plate with the CPU inside the socket. Lock the lever labelled
'Close 1st' first, then lock the lever labelled 'Open 1st' second. Using your
thumb gently push the load levers down to the lever locks.
1
2
Gently close
the load plate.
Push down and lock the
lever labelled 'Close 1st'.
OP
EN
1st
4
3
Push down and
lock the lever
labelled 'Open
1st'.
Lever Lock
OP
EN
OP
EN
1st
1st
Lever Lock
2-10
Chapter 2: Installation
Installing a Passive CPU Heatsink
1. Do not apply any thermal grease to the heatsink or the CPU die -- the required amount has already been applied.
2. Place the heatsink on top of the CPU so that the four mounting holes are
aligned with those on the Motherboard's and the Heatsink Bracket underneath.
3. Screw in two diagonal screws (i.e., the #1 and the #2 screws) until just snug
(-do not over-tighten the screws to avoid possible damage to the CPU.)
4. Finish the installation by fully tightening all four screws.
Screw#1
Screw#2
Motherboard
OP
EN
1s
t
Mounting Holes
Note: For optimized airflow, please follow your chassis airflow direction
to install the correct CPU heatsink direction. Graphic drawings included
in this manual are for reference only. They might look different from the
components installed in your system
2-11
X10SRL-F User’s Manual
Removing the Heatsink
Warning: We do not recommend that the CPU or the heatsink be removed. However,
if you do need to uninstall the heatsink, please follow the instructions below to prevent
damage to the CPU or the CPU socket.
1. Unscrew the heatsink screws from the motherboard in the sequence as
shown in the illustration below.
2. Gently wriggle the heatsink to loosen it from the CPU. (Do not use excessive
force when wriggling the heatsink!)
3. Once the heatsink is loosened, remove the heatsink from the CPU socket.
4. Remove the used thermal grease and clean the surface of the CPU and the
heatsink. Reapply the proper amount of thermal grease on the surface before
reinstalling the heatsink.
Loosen screws
in sequence as
shown.
Screw#4
Screw#1
Screw#2
Motherboard
Screw#3
2-12
Chapter 2: Installation
2-5 Installing DDR4 Memory
Note: Check the Supermicro website for recommended memory modules.
CAUTION
Exercise extreme care when installing or removing DIMM
modules to prevent any possible damage.
DIMM Installation
UID LED - LE1
UID - SW
COM1
VGA
USB2/3(3.0)
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
CPU
1
+
BT1
SP1
USB4/5
USB6/7
1
USB8/9
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
JPME2
JBR1
JTPM1
Rev: 1.01
DESIGNED IN USA
BAR CODE
Intel PCH
I-SATA5 JSD2
BIOS LICENSE
IPMI CODE
JPI2C1
JWD1
MAC CODE
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JSTBY1
5V STBY1
JL1
LE2
USB11(3.0)
J24
I_SATA4
S-SATA1 S-SATA0
JSD1
JD1
JF1
FAN4 FAN3
FAN2 FAN1
2. Push the release tabs outwards on
both ends of the DIMM slot to unlock
it.
3. Align the key of the DIMM module with the receptive point on the
memory slot.
Notches
4. Align the notches on both ends of
the module against the receptive
points on the ends of the slot.
6. Press the release tabs to the lock
positions to secure the DIMM module
into the slot.
2-13
Release Tabs
Press both notches
straight down into
the memory slot.
JPWR1
S-SATA3
S-SATA2
FANA
5. Use two thumbs together to press
the notches on both ends of the
module straight down into the slot
until the module snaps into place.
FAN5
JVR1
LAN
CTRL
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
USB0/1
IPMI_LAN
LAN1
LAN2
JPL2
LEDM1
COM2
1. Insert the desired number of DIMMs
into the memory slots, starting with
DIMMA1 (Channel A, Slot 1, see
the next page for the location). For
the system to work properly, please
use the memory modules of the
same type and speed in the same
motherboard.
BMC
X10SRL-F User’s Manual
Removing Memory Modules
Reverse the steps above to remove the DIMM modules from the motherboard.
Memory Support
DIMMD2
DIMMD1
DIMMC2
DIMMC1
DIMMB2
DIMMB1
DIMMA2
DIMMA1
Edge of the motherboard
1
1
The X10SRL-F supports eight ECC/Non-ECC DDR4 RDIMM/LRDIMM/UDIMM
at 1333/1600/1866/2133 MHz memory (1 DPC) up to 256GB RDIMM, 512GB
LRDIMM, or 64GB UDIMM. Populating these DIMM modules with a pair of memory
modules of the same type and size will result in interleaved memory, which will
improve memory performance. Please refer to the table below:
Memory Population Guidelines
Please follow the table below when populating the X10SRL-F.
DDR4 Unbuffered ECC (UDIMM) Memory
DIMM Slots per
Channel
DIMMs Populated per Channel
DIMM Type
POR Speeds
Ranks per DIMM (any
combination)
2
1
Unbuffered
DDR4
1333, 1600
Single Rank, Dual Rank
2
2
Unbuffered
DDR4
1333, 1600
Single Rank, Dual Rank
2-14
Chapter 2: Installation
Populating RDIMM Memory Modules
2 Slots per Channel RDIMM Population Configurations
Configuration
Number
POR Speed
DIMM1
DIMM0
1
DDR4-2133,
1866, 1600
Empty
Single-rank
2
DDR4-2133,
1866, 1600
Empty
Dual-rank
3
DDR4-1866,
1600
Single-rank
Single-rank
4
DDR4-1866,
1600
Single-rank
Dual-rank
5
DDR4-1866,
1600
Dual-rank
Dual-rank
Populating LRDIMM Memory Modules
2 Slots per Channel LRDIMM Population Configurations
Configuration
Number
POR Speed
DIMM1
DIMM0
1
DDR4-2133,
1866, 1600
Empty
Quad-rank+
2
DDR4-1866,
1600
Quad-rank+
Quad-rank+
2-15
X10SRL-F User’s Manual
Notes:
•Be sure to use memory modules of the same type and speed on the same
motherboard. Mixing of memory modules of different types and speeds is
not allowed.
•Due to memory allocation to system devices, the amount of memory that
remains available for operational use will be reduced when 4 GB of RAM
is used. The reduction in memory availability is disproportional. See the
following table for details.
Possible System Memory Allocation & Availability
System Device
Size
Physical Memory
Remaining (-Available)
(4 GB Total System
Memory)
Firmware Hub flash memory (System BIOS)
1 MB
3.99
Local APIC
4 KB
3.99
Area Reserved for the chipset
2 MB
3.99
I/O APIC (4 Kbytes)
4 KB
3.99
PCI Enumeration Area 1
256 MB
3.76
PCI Express (256 MB)
256 MB
3.51
PCI Enumeration Area 2 (if needed) -Aligned on 256-MB
boundary-
512 MB
3.01
VGA Memory
16 MB
2.85
TSEG
1 MB
2.84
Memory available to OS and other applications
2.84
2-16
Chapter 2: Installation
2-6 Connectors/IO Ports
The I/O ports are color coded in conformance with the industry standards. See the
figure below for the colors and locations of the various I/O ports.
Backplane I/O Panel
UID LED - LE1
UID - SW
COM1
VGA
USB2/3(3.0)
BMC
LAN1
LAN2
JPL2
COM2
LEDM1
LAN
CTRL
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
CPU
1
+
BT1
SP1
USB4/5
USB6/7
1
USB8/9
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
JPME2
DESIGNED IN USA
BAR CODE
Intel PCH
BIOS LICENSE
IPMI CODE
JPI2C1
JWD1
MAC CODE
JL1
LE2
JD1
JF1
FAN4 FAN3
USB11(3.0)
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JPWR1
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
JSTBY1
5V STBY1
J24
I_SATA4
I-SATA5 JSD2
S-SATA3
S-SATA2
JSD1
S-SATA1 S-SATA0
FANA
JBR1
JTPM1
Rev: 1.01
FAN2 FAN1
B
E
A
C
G
F
H
D
Backplane I/O Panel
A. COM1
F. USB Port 4 (3.0)
B. IPMI LAN
G. LAN1
C. USB Port 0 (2.0)
H. LAN2
D. USB Port 1 (2.0)
I. VGA Port
E. USB Port 3 (3.0)
J. UID Switch
2-17
I
J
X10SRL-F User’s Manual
Universal Serial Bus (USB)
Four Universal Serial Bus ports (USB 3.0 ports 2/3 and USB 2.0 ports 0/1) are
located on the I/O back panel. In addition, three USB 2.0 headers (USB 4/5, 6/7,
8/9), and two USB 3.0 connectors (USB 10, USB 11) are also located on the
motherboard to provide USB 3.0 support using USB cables (not included). See the
tables below for pin definitions.
Front Panel USB (2.0) 4/5, 6/7, 8/9
Pin Definitions
Pin #
Definition
Pin #
Definition
1
+5V
2
+5V
3
USB_PN2
4
USB_PN3
5
USB_PP2
6
USB_PP3
7
Ground
8
Ground
9
Key
10
Ground
A. Backpanel USB 2.0 #0/1
B. Backpanel USB 3.0 #2/3
C. Front Panel USB 2.0 #4/5
D. Front Panel USB 2.0 #6/7
E. Front Panel USB 2.0 #8/9
F. Front Panel USB 3.0 #10
G. Front Panel USB 3.0 #11
B
UID LED - LE1
UID - SW
A
COM1
VGA
USB2/3(3.0)
BMC
LAN1
LAN2
JPL2
COM2
LEDM1
LAN
CTRL
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
CPU
1
+
BT1
SP1
C
D
USB4/5
USB6/7
1
USB8/9
E
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
JPME2
DESIGNED IN USA
BAR CODE
BIOS LICENSE
IPMI CODE
JPI2C1
JWD1
MAC CODE
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JSTBY1
5V STBY1
JL1
LE2
USB11(3.0)
F
JD1
JF1
FAN4 FAN3
G
2-18
FAN2 FAN1
JPWR1
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
J24
I_SATA4
I-SATA5 JSD2
S-SATA3
S-SATA2
JSD1
S-SATA1 S-SATA0
FANA
JBR1
JTPM1
Rev: 1.01
Intel PCH
Chapter 2: Installation
Ethernet Ports
LAN Ports
Pin Definition
Two Gigabit Ethernet ports (LAN1/LAN2)
and an IPMI_LAN port are located on
Pin# Definition
the I/O Backpanel to provide network
connections. These ports accept RJ45
type cables.
Note: Please refer to the LED
Indicator Section for LAN LED
information.
1
SGND
9
TD0+
2
GND
10
TD0-
3
TD3+
11
Link 1000 LED
(Green, +3V3SB
4
TD3-
12
Link 1000 LED
(Yellow, +3V3SB)
5
TD2+
13
Act LED
6
TD2-
14
7
TD1+
15
SGND
8
TD1-
16
SGND
(NC: No Connection)
Serial Ports (COM1/COM2)
Serial Ports
Pin Definitions
Serial port COM1 is located next to USB
0/1 on the I/O backplane. Another Serial
port header (COM2) is located next to
IPMI_LAN on the motherboard. See the
table on the right for pin definitions.
Pin #
UID - SW
DSR
2
RXD
7
RTS
3
TXD
8
CTS
4
DTR
9
RI
5
SGND
10
SGND
B. LAN1
C. IPIMI_LAN
COM1
LAN
CTRL
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
CPU
1
+
BT1
SP1
USB4/5
USB6/7
1
USB8/9
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
JPME2
JBR1
JTPM1
Rev: 1.01
BAR CODE
I-SATA5 JSD2
IPMI CODE
JPI2C1
JWD1
MAC CODE
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JL1
LE2
USB11(3.0)
J24
I_SATA4
S-SATA1 S-SATA0
JSD1
BIOS LICENSE
JSTBY1
5V STBY1
JD1
JF1
FAN4 FAN3
FAN2 FAN1
2-19
JPWR1
S-SATA3
S-SATA2
FANA
DESIGNED IN USA
Intel PCH
D. COM1
E. COM2
JVR1
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
LAN1
LAN2
JPL2
A. LAN2
C D
USB2/3(3.0)
LEDM1
COM2
E
Definition
6
VGA
BMC
Pin #
DCD
A B
UID LED - LE1
Definition
1
X10SRL-F User’s Manual
Unit Identifier Switch/UID LED Indicator
UID Switch
A Unit Identifier (UID) switch and an LED
Indicator are located on the motherboard.
The UID switch is located next to the VGA
port on the backplane. The UID LED (LE1)
is located next to the UID switch. When you
press the UID switch, the UID LED will be
turned on. Press the UID switch again to
turn off the LED indicator. The UID Indicator
provides easy identification of a system unit
that may be in need of service.
Pin#
Definition
1
Ground
2
Ground
3
Button In
4
Button In
UID LED
Status
Color/State Status
Blue: On
Unit Identified
Note: UID can also be triggered
via IPMI on the motherboard. For
more information on IPMI, please
refer to the IPMI User's Guide
posted on our website @ http://
www.supermicro.com.
A. VGA
VGA Port
B. UID Switch
The onboard VGA port is located next to
LAN Ports 1/2 on the I/O backpanel. Use
the connection for VGA display.
C. UID LED
C B A
UID LED - LE1
UID - SW
COM1
VGA
USB2/3(3.0)
BMC
LAN1
LAN2
JPL2
COM2
LEDM1
LAN
CTRL
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
CPU
1
+
BT1
SP1
USB4/5
USB6/7
1
USB8/9
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
JPME2
DESIGNED IN USA
BAR CODE
Intel PCH
BIOS LICENSE
IPMI CODE
JPI2C1
JWD1
MAC CODE
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JL1
LE2
USB11(3.0)
JD1
JF1
FAN4 FAN3
2-20
FAN2 FAN1
JPWR1
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
JSTBY1
5V STBY1
J24
I_SATA4
I-SATA5 JSD2
S-SATA3
S-SATA2
JSD1
S-SATA1 S-SATA0
FANA
JBR1
JTPM1
Rev: 1.01
Chapter 2: Installation
Front Control Panel
JF1 contains header pins for various buttons and indicators that are normally located
on a control panel at the front of the chassis. These connectors are designed specifically for use with Supermicro chassis. See the figure below for the descriptions
of the front control panel buttons and LED indicators. Refer to the following section
for descriptions and pin definitions.
UID LED - LE1
UID - SW
COM1
VGA
USB2/3(3.0)
BMC
LAN1
LAN2
JPL2
COM2
LEDM1
LAN
CTRL
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
CPU
1
+
BT1
SP1
USB4/5
USB6/7
1
USB8/9
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
JPME2
JBR1
JTPM1
Rev: 1.01
DESIGNED IN USA
BAR CODE
Intel PCH
BIOS LICENSE
IPMI CODE
JPI2C1
JWD1
MAC CODE
JL1
LE2
JF1
FAN4 FAN3
USB11(3.0)
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JD1
FAN2 FAN1
JF1 Header Pins
20
19
Ground
NMI
X
X
P3V3
Power LED
HDD LED
P3V3_STB
NIC1 LED
P3V3_STB
NIC2 LED
P3V3_STB
P5V_STB
OH/Fan Fail LED
P3V3
PWR Fail LED
Ground
Ground
2
1
2-21
Reset
Reset Button
PWR
Power Button
JPWR1
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
JSTBY1
5V STBY1
J24
I_SATA4
FANA
S-SATA1 S-SATA0
I-SATA5 JSD2
S-SATA3
S-SATA2
JSD1
X10SRL-F User’s Manual
Front Control Panel Pin Definitions
NMI Button
NMI Button
Pin Definitions (JF1)
The non-maskable interrupt button
header is located on pins 19 and 20
of JF1. Refer to the table on the right
for pin definitions.
Pin#
Definition
19
Control
20
Ground
Power LED
Power LED
Pin Definitions (JF1)
The Power LED connection is located
on pins 15 and 16 of JF1. Refer to the
table on the right for pin definitions.
Pin#
Definition
15
3.3V
16
PWR LED
A. NMI
B. PWR LED
UID LED - LE1
UID - SW
COM1
VGA
20
USB2/3(3.0)
BMC
COM2
LEDM1
LAN
CTRL
19
Ground
NMI
X
JVR1
LAN
CTRL
B
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT3 PCI-E 3.0 X4(IN X8)
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
LAN1
LAN2
JPL2
CPU
A
X
P3V3
Power LED
HDD LED
P3V3_STB
NIC1 LED
P3V3_STB
1
+
BT1
P3V3_STB
NIC2 LED
SP1
P5V_STB
OH/Fan Fail LED
USB4/5
USB6/7
JBT1
P3V3
PWR Fail LED
1
USB8/9
JP3
JIPMB1
IPMI
X10SRL-F
Ground
Reset
Reset Button
Ground
PWR
Power Button
JPME2
JBR1
JTPM1
Rev: 1.01
BAR CODE
I-SATA5 JSD2
IPMI CODE
JPI2C1
JWD1
MAC CODE
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JSTBY1
5V STBY1
JL1
LE2
USB11(3.0)
J24
I_SATA4
S-SATA1 S-SATA0
JSD1
BIOS LICENSE
JD1
JF1
FAN4 FAN3
FAN2 FAN1
2-22
JPWR1
S-SATA3
S-SATA2
FANA
DESIGNED IN USA
Intel PCH
2
1
Chapter 2: Installation
HDD LED
HDD LED
Pin Definitions (JF1)
The HDD LED connection is located
on pins 13 and 14 of JF1. Attach a
cable here to indicate HDD activity. See the table on the right for pin
definitions.
Pin#
Definition
13
P3V3_STB
14
HD Active
NIC1/NIC2 LEDs
GLAN1/2 LED
Pin Definitions (JF1)
The NIC (Network Interface Controller) LED connection for GLAN Port 1
is located on pins 11 and 12 of JF1,
and the LED connection for GLAN
Port 2 is on pins 9 and 10. Attach the
NIC LED cables to the LED indicators
mentioned above to display network
activity. Refer to the layout below for
the locations of NIC LED indicators.
Pin#
Definition
9
P3V3_STB
10
NIC 2 Link/Acitivty
LED
11
P3V3_STB
12
NIC 1 Link/Acitivty
LED
A. HDD LED
B. NIC1 LED
C. NIC2 LED
UID LED - LE1
UID - SW
USB2/3(3.0)
NMI
COM2
X
LAN
CTRL
X
JVR1
LAN
CTRL
P3V3
Power LED
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
19
Ground
FAN5
USB0/1
IPMI_LAN
LAN1
LAN2
JPL2
LEDM1
20
COM1
VGA
BMC
CPU
1
+
BT1
A
HDD LED
P3V3_STB
B
NIC1 LED
P3V3_STB
C
NIC2 LED
P3V3_STB
P5V_STB
OH/Fan Fail LED
SP1
USB4/5
P3V3
PWR Fail LED
USB6/7
1
USB8/9
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
JPME2
JBR1
JTPM1
Rev: 1.01
BIOS LICENSE
IPMI CODE
JPI2C1
JWD1
MAC CODE
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JSTBY1
5V STBY1
JL1
LE2
USB11(3.0)
J24
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
JD1
JF1
FAN4 FAN3
FAN2 FAN1
2-23
JPWR1
I_SATA4
S-SATA1 S-SATA0
JSD1
Reset
Reset Button
Ground
PWR
Power Button
2
BAR CODE
Intel PCH
I-SATA5 JSD2
S-SATA3
S-SATA2
FANA
DESIGNED IN USA
Ground
1
X10SRL-F User’s Manual
Overheat (OH)/Fan Fail/PWR Fail/
UID LED
OH/Fan Fail/ PWR Fail/Blue_UID
LED Pin Definitions (JF1)
Pin#
Connect an LED cable to pins 7 and
8 of Front Control Panel to use the
Overheat, Fan Fail, and Power Fail
connections. Refer to the table on the
right for pin definitions.
Definition
7
P5V_STB
8
Red_LED-Cathode/OH/Fan Fail/
Power Fail
OH/Fan Fail/PWR Fail
LED Status (Red LED)
Power Fail LED
State
Definition
Off
Normal
On
Overheat
Flashing
1 Hz
Fan Fail
Flashing
1/4 Hz
Redundant
Power
Supply Fail
PWR Fail LED
Pin Definitions (JF1)
The Power Fail LED connection is
located on pins 5 and 6 of JF1. Refer to the table on the right for pin
definitions.
Pin#
Definition
5
3.3V
6
PWR LED Status
A.OH/Fan Fail/PWR Fail/UID LED
B. PWR Fail LED
UID LED - LE1
UID - SW
USB2/3(3.0)
COM2
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
CPU
A
1
+
BT1
USB4/5
B
1
JP3
JIPMB1
IPMI
X10SRL-F
JPME2
DESIGNED IN USA
P3V3_STB
P3V3_STB
P3V3_STB
NIC2 LED
P5V_STB
BIOS LICENSE
IPMI CODE
JPI2C1
JWD1
MAC CODE
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JSTBY1
5V STBY1
JL1
LE2
USB11(3.0)
J24
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
JD1
JF1
FAN4 FAN3
P3V3
PWR Fail LED
Ground
Reset
Reset Button
Ground
PWR
Power Button
2
BAR CODE
Intel PCH
FAN2 FAN1
2-24
JPWR1
I_SATA4
S-SATA1 S-SATA0
FANA
JBR1
JTPM1
Rev: 1.01
I-SATA5 JSD2
S-SATA3
S-SATA2
JSD1
HDD LED
NIC1 LED
OH/Fan Fail LED
USB6/7
JBT1
X
P3V3
Power LED
SP1
USB8/9
NMI
X
JVR1
LAN
CTRL
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPB1
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
19
Ground
FAN5
USB0/1
IPMI_LAN
LAN1
LAN2
JPL2
LEDM1
20
COM1
VGA
BMC
1
Chapter 2: Installation
Reset Button
Reset Button
Pin Definitions (JF1)
The Reset Button connection is located
on pins 3 and 4 of JF1. Attach it to a
hardware reset switch on the computer
case. Refer to the table on the right for
pin definitions.
Power Button
Pin#
Definition
3
Reset
4
Ground
Power Button
Pin Definitions (JF1)
The Power Button connection is located
on pins 1 and 2 of JF1. Momentarily
contacting both pins will power on/off
the system. This button can also be configured to function as a suspend button
(with a setting in the BIOS - See Chapter
4). To turn off the power when the system
is in suspend mode, press the button for
4 seconds or longer. Refer to the table on
the right for pin definitions.
Pin#
Definition
1
Signal
2
Ground
A. Reset Button
B. PWR Button
UID LED - LE1
20
UID - SW
USB2/3(3.0)
BMC
JPL2
COM2
LEDM1
LAN
CTRL
NMI
X
X
P3V3
Power LED
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X8(IN X16)
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPB1
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
LAN1
LAN2
19
Ground
COM1
VGA
CPU
HDD LED
P3V3_STB
NIC1 LED
P3V3_STB
P3V3_STB
NIC2 LED
1
+
BT1
SP1
Ground
USB6/7
1
JBT1
JP3
JIPMB1
IPMI
Ground
X10SRL-F
2
JPME2
JBR1
JTPM1
Rev: 1.01
BAR CODE
BIOS LICENSE
IPMI CODE
JPI2C1
JWD1
MAC CODE
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JSTBY1
5V STBY1
JL1
LE2
USB11(3.0)
J24
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
JD1
JF1
FAN4 FAN3
FAN2 FAN1
2-25
JPWR1
JSD1
I_SATA4
S-SATA1 S-SATA0
FANA
DESIGNED IN USA
Intel PCH
I-SATA5 JSD2
S-SATA3
S-SATA2
P3V3
PWR Fail LED
USB4/5
USB8/9
P5V_STB
OH/Fan Fail LED
1
A
Reset
Reset Button
PWR
Power Button
B
X10SRL-F User’s Manual
2-7 Connecting Cables
This section provides brief descriptions and pin-out definitions for onboard headers
and connectors. Be sure to use the correct cable for each header or connector.
For information on Backpanel USB and Front Panel USB ports, refer to page 2-17.
ATX Power 24-pin Connector
Pin Definitions (JPW1)
ATX Main PWR & CPU PWR
Connectors (J24 & JPWR1)
The 24-pin main power connector
(J24) is used to provide power to the
motherboard. The 8-pin CPU PWR
connector (JPWR1) is also required
for the processor. These power
connectors meet the SSI EPS 12V
specification. See the table on the
right for pin definitions.
Pin#
Definition
13
+3.3V
Pin #
1
+3.3V
Definition
14
-12V
2
+3.3V
15
GND
3
GND
16
PS_ON
4
+5V
17
GND
5
GND
18
GND
6
+5V
19
GND
7
GND
20
Res (NC)
8
PWR_OK
21
+5V
9
5VSB
22
+5V
10
+12V
23
+5V
11
+12V
24
GND
12
+3.3V
12V 8-pin Power Connector Pin Definitions
24-Pin Main PWR
Pins
Definition
1 through 4
Ground
5 through 8
+12V
(Required)
A. 24-Pin ATX Main PWR
UID LED - LE1
UID - SW
USB2/3(3.0)
BMC
COM2
LAN
CTRL
FAN5
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPB1
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
USB0/1
IPMI_LAN
LAN1
LAN2
JPL2
LEDM1
B. 8-Pin PWR
COM1
VGA
CPU
1
+
BT1
SP1
USB4/5
USB6/7
1
USB8/9
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
JPME2
DESIGNED IN USA
BAR CODE
BIOS LICENSE
IPMI CODE
MAC CODE
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JL1
LE2
USB11(3.0)
JD1
A
JPI2C1
JWD1
J24
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
JSTBY1
5V STBY1
JF1
FAN4 FAN3
FAN2 FAN1
2-26
JPWR1
I_SATA4
I-SATA5 JSD2
S-SATA3
S-SATA2
JSD1
S-SATA1 S-SATA0
FANA
JBR1
JTPM1
Rev: 1.01
Intel PCH
B
Chapter 2: Installation
Fan Headers (Fan 1-Fan 5 & Fan A )
Fan Header
Pin Definitions
The X10SRL-F has six fan headers (Fan 1-Fan
5 & Fan A). These fans are 4-pin fan headers.
Although pins 1-3 of the onboard fan headers
are backward compatible with the traditional
3-pin fans, we recommend that you use 4-pin
fans to take advantage of the fan speed control
via IPMI interface. This allows the fan speeds
to be automatically adjusted based on the motherboard temperature. Refer to the table on the
right for pin definitions.
Pin#
Definition
1
Ground (Black)
2
2.5A/+12V
(Red)
3
Tachometer
4
PWM_Control
Chassis Intrusion (JL1)
Chassis Intrusion
Pin Definitions (JL1)
A Chassis Intrusion header is located at JL1 on
the motherboard. Attach the appropriate cable
from the chassis to inform you of a chassis intrusion when the chassis is opened.
Pin#
Definition
1
Intrusion Input
2
Ground
A. Fan 1
UID LED - LE1
UID - SW
COM1
VGA
USB2/3(3.0)
BMC
JPL2
COM2
LEDM1
LAN
CTRL
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
G. Chassis Intrusion
1
+
SP1
USB6/7
1
JBT1
JP3
X10SRL-F
JPME2
DESIGNED IN USA
I-SATA3 I-SATA2 I-SATA1 I-SATA0
F
BIOS LICENSE
IPMI CODE
JPI2C1
JWD1
MAC CODE
JSTBY1
5V STBY1
JL1
LE2
USB11(3.0)
JPWR1
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
BAR CODE
G
J24
I_SATA4
I-SATA5 JSD2
S-SATA3
S-SATA2
JSD1
S-SATA1 S-SATA0
FANA
JBR1
JTPM1
Rev: 1.01
Intel PCH
JD1
JF1
FAN4 FAN3
D
C
B
2-27
C. Fan 3
F. Fan A
CPU
BT1
JIPMB1
IPMI
B. Fan 2
E. Fan 5
USB4/5
USB8/9
E
D. Fan 4
JVR1
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
LAN1
LAN2
FAN2 FAN1
A
X10SRL-F User’s Manual
Internal Speaker/Buzzer (SP1)
Internal Buzzer
Pin Definition
The Internal Speaker/Buzzer (SP1) is
used to provide audible indications for
Pin#
various beep codes. See the table on
the right for pin definitions.
Pin 1
Pos. (+)
Beep In
Pin 2
Neg. (-)
Alarm
Speaker
Overheat (OH)/Fan Fail
Definitions
OH/Fan Fail Indicator Status
Connect an LED cable to JOH1 to provide
warnings for chassis overheat/fan failure.
Refer to the table on the right for pin
definitions.
State
Definition
Off
Normal
On
Overheat
Flashing
Fan Fail
A. Internal Buzzer
B. Overheat/Fan Fail
UID LED - LE1
UID - SW
COM1
VGA
USB2/3(3.0)
BMC
LAN1
LAN2
JPL2
COM2
LEDM1
LAN
CTRL
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
CPU
1
BT1
+
A
SP1
USB4/5
USB6/7
1
USB8/9
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
JPME2
DESIGNED IN USA
I-SATA3 I-SATA2 I-SATA1 I-SATA0
BIOS LICENSE
IPMI CODE
JPI2C1
JWD1
MAC CODE
JSTBY1
5V STBY1
JL1
LE2
USB11(3.0)
JD1
JF1
FAN4 FAN3
2-28
FAN2 FAN1
JPWR1
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
BAR CODE
B
J24
I_SATA4
I-SATA5 JSD2
S-SATA3
S-SATA2
JSD1
S-SATA1 S-SATA0
FANA
JBR1
JTPM1
Rev: 1.01
Intel PCH
Chapter 2: Installation
DOM PWR Connector (JSD1)
DOM PWR
Pin Definitions
The Disk-On-Module (DOM) power
connectors, located at JSD1 and
JSD2, provide 5V power to a solid
state DOM storage device connected
to one of the SATA ports. See the table
on the right for pin definitions.
Pin#
Definition
1
5V
2
Ground
3
Ground
Standby Power
Standby Power
Pin Definitions
The Standby Power header is located
at JSTBY1 on the motherboard. See
the layout below for the location.
Pin#
Definition
1
+5V Standby
2
Ground
3
No Connection
A. DOM PWR 1
B. DOM PWR 2
C. Standby PWR
UID LED - LE1
UID - SW
COM1
VGA
USB2/3(3.0)
BMC
LAN1
LAN2
JPL2
COM2
LEDM1
LAN
CTRL
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
CPU
1
+
BT1
SP1
USB4/5
USB6/7
1
USB8/9
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
JPME2
B
BAR CODE
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JL1
C
LE2
USB11(3.0)
IPMI CODE
JPI2C1
JWD1
MAC CODE
JSTBY1
5V STBY1
JD1
JF1
FAN4 FAN3
FAN2 FAN1
2-29
JPWR1
A
BIOS LICENSE
J24
I_SATA4
I-SATA5 JSD2
S-SATA3
S-SATA2
JSD1
S-SATA1 S-SATA0
FANA
DESIGNED IN USA
JBR1
JTPM1
Rev: 1.01
Intel PCH
X10SRL-F User’s Manual
T-SGPIO 1/2/3 Headers
T-SGPIO/6-SGPIO
Pin Definitions
Two Serial-Link General Purpose Input/
Output headers (T-SGPIO 1/2/3) are
located on the motherboard. T-SGPIO
1/2/3 support onboard SATA interface.
See the table on the right for pin definitions.
Pin#
Definition
Pin
Definition
2
NC
1
NC
4
Data
3
Ground
6
Ground
5
Load
8
NC
7
Clock
Note: NC= No Connection
PWR SMB
Pin Definitions
Power SMB (I2C) Connector
Power System Management Bus (I2C)
Connector (JPI2C1) monitors power supply, fan and system temperatures. See
the table on the right for pin definitions.
Pin#
Definition
1
Clock
2
Data
3
PWR Fail
4
Ground
5
+3.3V
A. T-SGPIO 1
B. T-SGPIO 2
C. T-SGPIO 3
D. SMB Connector
UID LED - LE1
UID - SW
COM1
VGA
USB2/3(3.0)
BMC
JPL2
COM2
LEDM1
LAN
CTRL
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
LAN1
LAN2
CPU
1
+
BT1
SP1
USB4/5
USB6/7
1
USB8/9
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
JPME2
DESIGNED IN USA
BAR CODE
BIOS LICENSE
IPMI CODE
JPI2C1
JWD1
MAC CODE
I-SATA3 I-SATA2 I-SATA1 I-SATA0
B
A
JSTBY1
5V STBY1
JL1
LE2
USB11(3.0)
JD1
JF1
FAN4 FAN3
FAN2 FAN1
2-30
JPWR1
C
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
J24
I_SATA4
I-SATA5 JSD2
S-SATA3
S-SATA2
JSD1
S-SATA1 S-SATA0
FANA
JBR1
JTPM1
Rev: 1.01
Intel PCH
D
Chapter 2: Installation
TPM Header/Port 80 Header
TPM/Port 80 Header
Pin Definitions
A Trusted Platform Module/Port 80
header is located at JTPM1 to provide
Pin #
TPM support and Port 80 connection.
Use this header to enhance system
performance and data security. See
the table on the right for pin definitions.
Definition
Pin #
Definition
1
LCLK
2
GND
3
LFRAME#
4
<(KEY)>
5
LRESET#
6
+5V (X)
7
LAD 3
8
LAD 2
9
+3.3V
10
LAD1
11
LAD0
12
GND
13
SMB_CLK
14
SMB_DAT
15
+3V_STB
16
SERIRQ
17
GND
18
CLKRUN#
19
LPCPD#
20
LDRQ# (X)
Video Connector
VGA/CRT Pin
Definitions
A Video (VGA) connector is located
next to the COM Port on the I/O
backpanel. This connector is used
to provide video and CRT display.
Refer to the board layout below for
the location.
Pin#
Definition
Pin#
Definition
1
Red
10
Ground
2
Green
11
MS0
3
Blue
12
MS1: SDA (DDC Data)
4
MS2
13
HSYNC
5
Ground
14
VSYSNC
6
Ground
15
MS3: SCL (DDC CLK)
7
Ground
16
Case
8
Ground
17
Case
9
NC
NC= No Connection
B
UID LED - LE1
UID - SW
COM1
VGA
USB2/3(3.0)
BMC
LAN1
LAN2
JPL2
COM2
LEDM1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
CPU
1
+
BT1
SP1
USB4/5
USB6/7
1
USB8/9
JBT1
JIPMB1
IPMI
JPME2
JBR1
JTPM1
X10SRL-F
Rev: 1.01
DESIGNED IN USA
BAR CODE
Intel PCH
BIOS LICENSE
IPMI CODE
JPI2C1
JWD1
MAC CODE
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JL1
LE2
USB11(3.0)
J24
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
JSTBY1
5V STBY1
JD1
JF1
FAN4 FAN3
FAN2 FAN1
2-31
JPWR1
I_SATA4
I-SATA5 JSD2
S-SATA3
S-SATA2
JSD1
S-SATA1 S-SATA0
FANA
JP3
A
A. TPM/Port 80
B. VGA Port
JVR1
LAN
CTRL
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPB1
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
X10SRL-F User’s Manual
2-8 Jumper Settings
Explanation of Jumpers
To modify the operation of the motherboard, jumpers can be used to choose
between optional settings. Jumpers create
shorts between two pins to change the
function of the connector. Pin 1 is identified
with a square solder pad on the printed
circuit board.
Note: On two-pin jumpers,
"Closed" means the jumper is on,
and "Open" means the jumper is
off the pins.
LAN1/LAN2 Enable/Disable
GLAN Enable
Jumper Settings
Jumpers JPL1/JPL2 enable or disable
LAN ports 1/2 on the motherboard. See
the table on the right for jumper settings.
The default setting is enabled.
Pin#
Definition
1-2
Enabled (default)
2-3
Disabled
A. JPL1: LAN1 Enable
B. JPL2: LAN2 Enable
UID LED - LE1
UID - SW
COM1
VGA
USB2/3(3.0)
BMC
B
COM2
LEDM1
LAN1
LAN2
JPL2
LAN
CTRL
A
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
CPU
1
+
BT1
SP1
USB4/5
USB6/7
1
USB8/9
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
JPME2
JBR1
JTPM1
Rev: 1.01
BAR CODE
I-SATA5 JSD2
IPMI CODE
JPI2C1
JWD1
MAC CODE
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JL1
LE2
USB11(3.0)
J24
I_SATA4
S-SATA1 S-SATA0
JSD1
BIOS LICENSE
JSTBY1
5V STBY1
JD1
JF1
FAN4 FAN3
FAN2 FAN1
2-32
JPWR1
S-SATA3
S-SATA2
FANA
DESIGNED IN USA
Intel PCH
Chapter 2: Installation
CMOS Clear (JBT1)
JBT1 is used to clear the saved system setup configuration stored in the CMOS
chip. To clear the contents of the CMOS, completely shut down the system, remove
the AC power cord and then short JBT1 with a jumper. Remove the jumper before
powering on the system again. This will erase all user settings and revert everything
to their factory-set defaults.
PCI-E Slot SMB Enable (I2C1/I2C2)
PCI-E Slot_SMB Enable
Jumper Settings
Use Jumpers I2C1/I2C2 to enable PCI-E
SMB (System Management Bus) support
to improve system management for the
PCI-E slots. See the table on the right
for jumper settings.
Jumper Setting
Definition
1-2
Enabled
2-3
Disabled
(Default)
A. Clear CMOS
B. JI2C1
C. JI2C2
UID LED - LE1
UID - SW
COM1
VGA
USB2/3(3.0)
BMC
COM2
LAN
CTRL
JPL1
FAN5
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT5 PCI-E 3.0 X8
C
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT3 PCI-E 3.0 X4(IN X8)
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JPG1
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JI2C1
JI2C2
CPU
1
+
BT1
SP1
USB4/5
USB6/7
USB8/9
JBT1
JP3
A
1
B
JPL2
LEDM1
USB0/1
IPMI_LAN
LAN1
LAN2
JIPMB1
IPMI
X10SRL-F
JPME2
DESIGNED IN USA
BAR CODE
BIOS LICENSE
IPMI CODE
JPI2C1
JWD1
MAC CODE
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JSTBY1
5V STBY1
JL1
LE2
USB11(3.0)
J24
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
JD1
JF1
FAN4 FAN3
FAN2 FAN1
2-33
JPWR1
I_SATA4
I-SATA5 JSD2
S-SATA3
S-SATA2
JSD1
S-SATA1 S-SATA0
FANA
JBR1
JTPM1
Rev: 1.01
Intel PCH
X10SRL-F User’s Manual
Manufacture Mode Select
ME Mode Select
Jumper Settings
Close this jumper (JPME2) to bypass
SPI flash security and force the system
Jumper Setting
to use the Manufacture Mode which will
allow the user to flash the system firmware from a host server to modify system
settings. See the table on the right for
jumper settings.
Definition
1-2
Normal (Default)
2-3
Manufacture Mode
VGA Enable
VGA Enable
Jumper Settings
Jumper JPG1 allows the user to enable
the onboard VGA connector. The default
setting is 1-2 to enable the connection.
See the table on the right for jumper
settings.
Jumper Setting
Definition
1-2
Enabled (Default)
2-3
Disabled
A. JPME2
B. VGA Enable
UID LED - LE1
UID - SW
COM1
VGA
USB2/3(3.0)
BMC
COM2
LAN
CTRL
JPL1
FAN5
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X8(IN X16)
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPB1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JPG1
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JI2C1
JI2C2
CPU
1
+
BT1
SP1
USB4/5
USB6/7
1
B
LAN1
LAN2
JPL2
LEDM1
USB0/1
IPMI_LAN
USB8/9
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
JTPM1
Rev: 1.01
JBR1
JPME2
A
BAR CODE
I-SATA5 JSD2
IPMI CODE
JPI2C1
JWD1
MAC CODE
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JL1
LE2
USB11(3.0)
J24
I_SATA4
S-SATA1 S-SATA0
JSD1
BIOS LICENSE
JSTBY1
5V STBY1
JD1
JF1
FAN4 FAN3
FAN2 FAN1
2-34
JPWR1
S-SATA3
S-SATA2
FANA
DESIGNED IN USA
Intel PCH
Chapter 2: Installation
Watch Dog Enable/Disable
Watch Dog
Jumper Settings
Watch Dog (JWD1) is a system monitor that can reboot the system when a
Jumper Setting
software application hangs. Close Pins
1-2 to reset the system if an application hangs. Close pins 2-3 to generate a
non-maskable interrupt signal for the application that hangs. See the table on the
right for jumper settings. Watch Dog must
also be enabled in the BIOS.
Definition
Pins 1-2
Reset (default)
Pins 2-3
NMI
Open
Disabled
BIOS Recovery Enable
BIOS Recovery
Jumper Settings
Close pins 2 and 3 of jumper JBR1 for
BIOS recovery. The default setting is on
pins 1 and 2 for normal operation. See
the table on the right for jumper settings.
Jumper Setting
Definition
Pins 1-2
Normal
Pins 2-3
BIOS Recovery
A. Watch Dog Enable
B. BIOS Recovery
UID LED - LE1
UID - SW
COM1
VGA
USB2/3(3.0)
BMC
JPL2
COM2
LEDM1
LAN
CTRL
FAN5
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
USB0/1
IPMI_LAN
LAN1
LAN2
CPU
1
+
BT1
SP1
USB4/5
USB6/7
1
USB8/9
JBT1
JP3
JIPMB1
IPMI
B
X10SRL-F
JPME2
DESIGNED IN USA
BAR CODE
BIOS LICENSE
IPMI CODE
JPI2C1
JWD1
MAC CODE
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JSTBY1
5V STBY1
JL1
LE2
USB11(3.0)
JD1
JF1
FAN4 FAN3
FAN2 FAN1
2-35
JPWR1
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
J24
I_SATA4
I-SATA5 JSD2
S-SATA3
S-SATA2
JSD1
S-SATA1 S-SATA0
FANA
JBR1
JTPM1
Rev: 1.01
Intel PCH
A
X10SRL-F User’s Manual
2-9 Onboard Indicators
LAN1/LAN2
Activity LED
Link LED
LAN 1/LAN 2 LEDs
Two LAN ports (LAN 1/LAN 2) are located
on the I/O backplane of the motherboard.
Each Ethernet LAN port has two LEDs.
The yellow LED indicates activity, while the
Link LED may be green, amber, or off to
indicate the speed of the connections. See
the tables on the right for more information.
GLAN 1/2 Activity Indicator
LED Settings
Color
Status
Definition
Yellow
Flashing
Active
GLAN Ports 1/2 Link Indicator
LED Settings
LED Color
Definition
Off
No Connection/10 Mbps/
Green
100 Mbps
Amber
1 Gbps
LAN 1/LAN 2
IPMI Dedicated LAN LEDs
IPMI LAN
Activity LED
Link LED
In addition to the Gigabit Ethernet ports,
an IPMI Dedicated LAN is also located
above the Backplane USB ports 0/1 on the
motherboard. The yellow LED on the right
indicates activity, while the green/amber
LED on the left indicates the speed of the
connection. See the table on the right for
more information.
IPMI LAN
(X8ST3-F)
Color/State
IPMI LAN Link LED (Left) &
Activity LED (Right)
Link (Left)
Activity (Right)
Definition
Amber: Solid
1 Gbps
Green: Solid
100 Mbps
Yellow: Blinking
Active
A. LAN 1/2 LEDs
B. IPMI_LAN LED
B
A
UID LED - LE1
UID - SW
COM1
VGA
USB2/3(3.0)
BMC
LAN1
LAN2
JPL2
COM2
LEDM1
LAN
CTRL
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
CPU
1
+
BT1
SP1
USB4/5
USB6/7
1
USB8/9
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
JPME2
DESIGNED IN USA
BAR CODE
BIOS LICENSE
IPMI CODE
JPI2C1
JWD1
MAC CODE
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JL1
LE2
USB11(3.0)
J24
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
JSTBY1
5V STBY1
JD1
JF1
FAN4 FAN3
FAN2 FAN1
2-36
JPWR1
I_SATA4
I-SATA5 JSD2
S-SATA3
S-SATA2
JSD1
S-SATA1 S-SATA0
FANA
JBR1
JTPM1
Rev: 1.01
Intel PCH
Chapter 2: Installation
Onboard Power LED (LE2)
Onboard PWR LED Indicator
LED Status
An Onboard Power LED is located
at LE2 on the motherboard. When
Status
LE2 is on, the AC power cable is
connected. Make sure to disconnect
the power cable before removing or
installing any component. See the
layout below for the LED location.
Definition
Off
System Off
On
System on, or
System off and PWR
Cable Connected
BMC Heartbeat LED (LEDM1)
BMC Heartbeat LED
Status
A BMC Heartbeat LED is located at
LEDM1 on the X10SRL-F. See the table
on the right for more information.
Color/State
Green:
Blinking
Definition
BMC: Normal
A. BMC LED
B. Onboard Power LED
UID LED - LE1
BMC
A
UID - SW
COM1
VGA
USB2/3(3.0)
LAN1
LAN2
JPL2
COM2
LEDM1
LAN
CTRL
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
CPU
1
+
BT1
SP1
USB4/5
USB6/7
1
USB8/9
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
JPME2
JBR1
JTPM1
Rev: 1.01
BAR CODE
I-SATA5 JSD2
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
I-SATA3 I-SATA2 I-SATA1 I-SATA0
JL1
B
LE2
USB11(3.0)
IPMI CODE
JPI2C1
JWD1
MAC CODE
J24
I_SATA4
S-SATA1 S-SATA0
JSD1
BIOS LICENSE
JSTBY1
5V STBY1
JD1
JF1
FAN4 FAN3
FAN2 FAN1
2-37
JPWR1
S-SATA3
S-SATA2
FANA
DESIGNED IN USA
Intel PCH
X10SRL-F User’s Manual
2-10 SATA Connections
SATA Connections
SATA/SAS Connectors
Pin Definitions
Ten SATA 3.0 connectors (I-SATA 0-5) and (SSATA 0-3) are located on the board. I-SATA 0-5
ports are supported by the AHCI controller and
are compatible with RAID 0, 1, 5, 10. S-SATA 0-3
ports are supported by the sSATA controller and
are compatible with RAID 0, 1, 5, 10. These Serial
Link connections provide faster data transmission
than legacy Parallel ATA. See the table on the
right for pin definitions.
Pin#
Signal
1
Ground
2
SATA_TXP
3
SATA_TXN
4
Ground
5
SATA_RXN
6
SATA_RXP
7
Ground
A. I-SATA 0
B. I-SATA 1
C. I-SATA 2
D. I-SATA 3
E. I-SATA 4
F. I-SATA 5
G. S-SATA 0
H. S-SATA 1
I. S-SATA 2
J. S-SATA 3
UID LED - LE1
UID - SW
COM1
VGA
USB2/3(3.0)
BMC
LAN1
LAN2
JPL2
COM2
LEDM1
LAN
CTRL
JVR1
LAN
CTRL
DIMMC1
DIMMC2
DIMMD1
DIMMD2
DIMMB2
DIMMB1
DIMMA2
DIMMA1
CPU SLOT7 PCI-E 3.0 X8
CPU SLOT6 PCI-E 3.0 X8(IN X16)
CPU SLOT5 PCI-E 3.0 X8
CPU SLOT4 PCI-E 3.0 X8(IN X16)
JPB1
CPU SLOT3 PCI-E 3.0 X4(IN X8)
JPG1
CPU SLOT2 PCI-E 3.0 X4(IN X8)
JI2C1
JI2C2
PCH SLOT1 PCI-E 2.0 X4(IN X8)
JPL1
FAN5
USB0/1
IPMI_LAN
CPU
1
+
BT1
SP1
USB4/5
USB6/7
1
USB8/9
JBT1
JP3
JIPMB1
IPMI
X10SRL-F
Rev: 1.01
JPME2
DESIGNED IN USA
BAR CODE
Intel PCH
BIOS LICENSE
JPI2C1
JWD1
JL1
LE2
USB11(3.0)
JD1
JF1
FAN4 FAN3
D C B A
2-38
FAN2 FAN1
JPWR1
T-SGPIO3
T-SGPIO2
JOH1
T-SGPIO1
USB10(3.0)
I-SATA3 I-SATA2 I-SATA1 I-SATA0
L
IPMI CODE
MAC CODE
JSTBY1
5V STBY1
J24
E
I_SATA4
FANA
I-SATA5 JSD2
S-SATA3
S-SATA2
JSD1
S-SATA1 S-SATA0
I
H
G
JBR1
JTPM1
J
F
Chapter 3: Troubleshooting
Chapter 3
Troubleshooting
3-1 Troubleshooting Procedures
Use the following procedures to troubleshoot your system. If you have followed all
of the procedures below and still need assistance, refer to the ‘Technical Support
Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter.
Always disconnect the AC power cord before adding, changing or installing any
hardware components.
Before Power On
1. Make sure that the Standby PWR LED is not on. (Note: If it is on, the
onboard power is on. Be sure to unplug the power cable before installing or
removing the components.)
2. Make sure that there are no short circuits between the motherboard and
chassis.
3. Disconnect all ribbon/wire cables from the motherboard, including those for
the keyboard and mouse. Also, be sure to remove all add-on cards.
4. Install a CPU and heatsink (-be sure that it is fully seated) and then connect
the chassis speaker and the power LED to the motherboard. Check all jumper
settings as well.
No Power
1. Make sure that there are no short circuits between the motherboard and
chassis.
2. Make sure that all jumpers are set to their default positions.
3. Check if the 115V/230V switch on the power supply is properly set.
4. Turn the power switch on and off to test the system.
5. The battery on your motherboard may be old. Check to make sure that it still
supplies ~3VDC. If it does not, replace it with a new one.
3-1
X10SRL-F User’s Manual
No Video
1. If the power is on, but you have no video--in this case, you will need to remove all the add-on cards and cables first.
2. Use the speaker to determine if any beep codes exist. (Refer to Appendix A
for details on beep codes.)
3. Remove all memory modules and turn on the system. (If the alarm is on,
check the specifications of memory modules, reset the memory or try a different one.)
Memory Errors
1. Make sure that the DIMM modules are properly installed and fully seated in
the slots.
2. You should be using ECC DDR4 1333/1600/1866/2133 MHz memory recommended by the manufacturer. Also, it is recommended that you use the
memory modules of the same type and speed for all DIMMs in the system.
Do not use memory modules of different sizes, different speeds and different
types on the same motherboard.
3. Check for bad DIMM modules or slots by swapping modules between slots to
see if you can locate the faulty ones.
4. Check the switch of 115V/230V power supply.
Losing the System’s Setup Configuration
1. Please be sure to use a high quality power supply. A poor quality power supply may cause the system to lose CMOS setup information. Refer to Section
1-6 for details on recommended power supplies.
2. The battery on your motherboard may be old. Check to verify that it still supplies ~3VDC. If it does not, replace it with a new one.
3. If the above steps do not fix the Setup Configuration problem, contact your
vendor for repairs.
3-2
Chapter 3: Troubleshooting
3-2 Technical Support Procedures
Before contacting Technical Support, please make sure that you have followed all
the steps listed below. Also, Note that as a motherboard manufacturer, Supermicro
does not sell directly to end users, so it is best to first check with your distributor or
reseller for troubleshooting services. They should know of any possible problem(s)
with the specific system configuration that was sold to you.
1. Please go through the ‘Troubleshooting Procedures’ and 'Frequently Asked
Question' (FAQ) sections in this chapter or see the FAQs on our website
(http://www.supermicro.com/support/faqs/) before contacting Technical Support.
2. BIOS upgrades can be downloaded from our website at (http://www.supermicro.com/support/bios/).
Note: Not all BIOS can be flashed. Some cannot be flashed; it depends
on the boot block code of the BIOS.
3. If you've followed the instructions above to troubleshoot your system, and still
cannot resolve the problem, then contact Supermicro's technical support and
provide them with the following information:
•Motherboard model and PCB revision number
•BIOS release date/version (this can be seen on the initial display when your
system first boots up)
•System configuration
•An example of a Technical Support form is on our website at
(http://www.su-
permicro.com/support/contact.cfm).
4. Distributors: For immediate assistance, please have your account number
ready when placing a call to our technical support department. We can be
reached by e-mail at support@supermicro.com, by phone at: (408) 5038000, option 2, or by fax at (408)503-8019.
3-3
X10SRL-F User’s Manual
3-3 Frequently Asked Questions
Question: What type of memory does my motherboard support?
Answer: The X10SRL-F supports up to 256GB of RDIMM and 512Gb of LRDIMM
DDR4 1333/1600/1866/2133 MHz in eight memory slots. See Section 2-5 for details
on installing memory.
Question: How do I update my BIOS?
Answer: We do NOT recommend that you upgrade your BIOS if you are not
experiencing any problems with your system. Updated BIOS files are located on
our website at http://www.supermicro.com/support/bios/. Please check our BIOS
warning message and the information on how to update your BIOS on our website.
Select your motherboard model and download the BIOS ROM file to your computer.
Also, check the current BIOS revision to make sure that it is newer than your BIOS
before downloading. You may choose the zip file. If you choose the zipped BIOS
file, please unzip the BIOS file onto a bootable device or a USB pen/thumb drive.
To flash the BIOS, run the batch file named "flash.bat" with the new BIOS ROM
file from your bootable device or USB pen/thumb drive. Use the following format:
F:\> flash.bat BIOS-ROM-filename.xxx <Enter>
Note: Always use the file named “flash.bat” to update the BIOS, and insert
a space between "flash.bat" and the filename. The BIOS-ROM-filename
will bear the motherboard name (i.e., X10SRL-F) and build version as the
extension. For example, "X10SRL-F.115".
When the BIOS flashing screen is completed, power off to reboot the
system. Power on and at this point, you will need to load the BIOS defaults. Press <Del> to go to the BIOS setup screen, and select "Restore
Defaults" to load the default settings. Next, press <F4> to save and exit.
Then reboot the system.
Warning: Do not shut down or reset the system while updating the BIOS to prevent
possible system boot failure!
Note: The SPI BIOS chip installed on this motherboard is not removable.
To repair or replace a damaged BIOS chip, please send your motherboard
to RMA at Supermicro for service.
Question: I think my BIOS is corrupted. How can I recover my BIOS?
Answer: Please see Appendix C-BIOS Recovery for detailed instructions.
Question: What is the heatsink part number for my X10SRL-F motherboard?
Answer: For the 1U passive heatsink, use SNK-P0047PS (back plate is included).
For the 2U/3U active heatsink, use SNK-P0048AP4. For the 4U active heatsink,
use SNK-P0050AP4.
3-4
Chapter 3: Troubleshooting
3-4 Battery Removal and Installation
Battery Removal
To remove the onboard battery, follow the steps below:
1. Power off your system and unplug your power cable.
2. Locate the onboard battery as shown below.
3. Using a tool such as a pen or a small screwdriver, push the battery lock outwards to unlock it. Once unlocked, the battery will pop out from the holder.
4. Remove the battery.
Proper Battery Disposal
Warning: Please handle used batteries carefully. Do not damage the battery in any
way; a damaged battery may release hazardous materials into the environment. Do
not discard a used battery in the garbage or a public landfill. Please comply with the
regulations set up by your local hazardous waste management agency to dispose of
your used battery properly.
Battery Installation
1. To install an onboard battery, follow the steps 1 & 2 above and continue
below:
2. Identify the battery's polarity. The positive (+) side should be facing up.
3. Insert the battery into the battery holder and push it down until you hear a
click to ensure that the battery is securely locked.
Warning: When replacing a battery, be sure to only replace it with the same type.
OR
3-5
X10SRL-F User’s Manual
3-5 Returning Merchandise for Service
A receipt or copy of your invoice marked with the date of purchase is required
before any warranty service will be rendered. You can obtain service by calling
your vendor for a Returned Merchandise Authorization (RMA) number. For faster
service, you may also obtain RMA authorizations online (http://www.supermicro.
com/RmaForm/). When you return the motherboard to the manufacturer, the RMA
number should be prominently displayed on the outside of the shipping carton, and
mailed prepaid or hand-carried. Shipping and handling charges will be applied for
all orders that must be mailed when service is complete.
This warranty only covers normal consumer use and does not cover damages
incurred in shipping or from failure due to the alteration, misuse, abuse or improper
maintenance of products.
During the warranty period, contact your distributor first for any product problems.
3-6
Chapter 4: AMI BIOS
Chapter 4
BIOS
4-1 Introduction
This chapter describes the AMI BIOS setup utility for the X10SRL-F. The ROM BIOS
is stored in a Flash EEPROM and can be easily updated. This chapter describes
the basic navigation of the AMI BIOS setup utility screens.
Note: For AMI BIOS recovery, please refer to the UEFI BIOS Recovery
Instructions in Appendix C.
Starting BIOS Setup Utility
To enter the AMI BIOS setup utility screens, press the <Delete> key while the
system is booting up.
Note: In most cases, the <Delete> key is used to invoke the AMI BIOS
setup screen. There are a few cases when other keys are used, such as
<F1>, <F2>, etc.
Each main BIOS menu option is described in this manual. The AMI BIOS setup
menu screen has two main frames. The left frame displays all the options that can
be configured. Grayed-out options cannot be configured. Options in blue can be
configured by the user. The right frame displays the key legend. Above the key
legend is an area reserved for a text message. When an option is selected in the
left frame, it is highlighted in white. Often a text message will accompany it.
Note: the AMI BIOS has default text messages built in. Supermicro retains
the option to include, omit, or change any of these text messages.
The AMI BIOS setup utility uses a key-based navigation system called "hot keys."
Most of the AMI BIOS setup utility "hot keys" can be used at any time during the
setup navigation process. These keys include <F1>, <F4>, <Enter>, <Esc>, arrow
keys, etc.
Note: Options printed in Bold are default settings.
How To Change the Configuration Data
The configuration data that determines the system parameters may be changed by
entering the AMI BIOS setup utility. This setup utility can be accessed by pressing
<Del> at the appropriate time during system boot.
4-1
X10SRL-F User’s Manual
How to Start the Setup Utility
Normally, the only visible Power-On Self-Test (POST) routine is the memory test.
As the memory is being tested, press the <Delete> key to enter the main menu of
the AMI BIOS setup utility. From the main menu, you can access the other setup
screens. An AMI BIOS identification string is displayed at the left bottom corner of
the screen, below the copyright message.
Warning: Do not upgrade the BIOS unless your system has a BIOS-related issue.
Flashing the wrong BIOS can cause irreparable damage to the system. In no event
shall Supermicro be liable for direct, indirect, special, incidental, or consequential damages arising from a BIOS update. If you have to update the BIOS, do not shut down
or reset the system while the BIOS is updating. This is to avoid possible boot failure.
4-2 Main Setup
When you first enter the AMI BIOS setup utility, you will enter the Main setup screen.
You can always return to the Main setup screen by selecting the Main tab on the
top of the screen. The Main BIOS setup screen is shown below.
The following Main menu items will be displayed:
4-2
Chapter 4: AMI BIOS
System Date/System Time
Use this option to change the system date and time. Highlight System Date or
System Time using the arrow keys. Enter new values using the keyboard. Press the
<Tab> key or the arrow keys to move between fields. The date must be entered in
Day MM/DD/YYYY format. The time is entered in HH:MM:SS format.
Note: The time is in the 24-hour format. For example, 5:30 P.M. appears
as 17:30:00.
Supermicro X10SRL-F
BIOS Version: This item displays the version of the BIOS ROM used in the
system.
Build Date: This item displays the date when the version of the BIOS ROM
used in the system was built.
Memory Information
Total Memory: This item displays the total size of memory available in the
system.
Memory Speed: This item displays the default speed of the memory modules
installed in the system..
4-3
X10SRL-F User’s Manual
4-3 Advanced Setup Configurations
Use the arrow keys to select Advanced setup and press <Enter> to access the
submenu items:
Warning: Take Caution when changing the Advanced settings. An incorrect value, a
very high DRAM frequency or an incorrect BIOS timing setting may cause the system
to malfunction. When this occurs, restore the setting to the manufacture default setting.
Boot
Feature
Quiet Boot
Use this feature to select the screen between displaying POST messages or the
OEM logo at bootup. Select Disabled to display the POST messages. Select Enabled to display the OEM logo instead of the normal POST messages. The options
are Enabled and Disabled.
AddOn ROM Display Mode
Use this item to set the display mode for the Option ROM. Select Keep Current to
use the current AddOn ROM display setting. Select Force BIOS to use the Option
ROM display mode set by the system BIOS. The options are Force BIOS and
Keep Current.
Bootup Num-Lock
Use this feature to set the Power-on state for the Numlock key. The options are
Off and On.
4-4
Chapter 4: AMI BIOS
Wait For 'F1' If Error
Select Enabled to force the system to wait until the 'F1' key is pressed if an error
occurs. The options are Disabled and Enabled.
INT19 (Interrupt 19) Trap Response
Interrupt 19 is the software interrupt that handles the boot disk function. When this
item is set to Immediate, the ROM BIOS of the host adaptors will "capture" Interrupt 19 at bootup immediately and allow the drives that are attached to these host
adaptors to function as bootable disks. If this item is set to Postponed, the ROM
BIOS of the host adaptors will not capture Interrupt 19 immediately and allow the
drives attached to these adaptors to function as bootable devices at bootup. The
options are Immediate and Postponed.
Re-try Boot
When EFI Boot is selected, the system BIOS will automatically reboot the system
from an EFI boot device after its initial boot failure. Select Legacy Boot, to allow
the BIOS to automatically reboot the system from a Legacy boot device after its
initial boot failure. The options are Disabled, Legacy Boot, and EFI Boot.
Power Configuration
DeepSx Power Policies
Use this item to configure the Advanced Configuration and Power Interface (ACPI)
settings for the system. Enable S3 to use Standby Mode (Suspend-to-RAM) and
maintain power supply to the system RAM when the system is in the sleep mode.
Enable S4 to use Hibernation mode (Suspend to Disk) so that all data stored in of
the main memory can be saved in a non-volatile memory area such as in a hard
drive and then power down the system. Enable S5 to power off the whole system
except the power supply unit (PSU) and keep the power button "alive" so that the
user can "wake-up" the system by using an USB keyboard or mouse. The options
are Disabled, Enabled in S5, Enabled in S4-S5, and Enabled in S3-S4-S5,
Watch Dog Function
Select Enabled to allow the Watch Dog timer to reboot the system when it is inactive for more than 5 minutes. The options are Enabled and Disabled.
Power Button Function
This feature controls how the system shuts down when the power button is pressed.
Select 4 Seconds Override for the user to power off the system after pressing and
holding the power button for 4 seconds or longer. Select Instant Off to instantly
power off the system as soon as the user presses the power button. The options
are 4 Seconds Override and Instant Off.
4-5
X10SRL-F User’s Manual
Restore on AC Power Loss
Use this feature to set the power state after a power outage. Select Power-Off for
the system power to remain off after a power loss. Select Power-On for the system
power to be turned on after a power loss. Select Last State to allow the system
to resume its last power state before a power loss. The options are Power-On,
Stay-Off and Last State.
CPU
Configuration
Warning! Setting the wrong values in the following sections may cause the system
to malfunction.
CPU Configuration
The following CPU information will be displayed:
•Processor Socket
•Processor ID
•Processor Frequency
•Max (Maximum) CPU Speed
•Min (Minimum) CPU Speed
•Processor Max Ratio
•Processor Min Ratio
•Microcode Revision
•L1 Cache RAM
•L2 Cache RAM
•L3 Cache RAM
•CPU1 Version
Clock Spread Spectrum
Select Enable for Clock Spectrum support, which will allow the BIOS to monitor
and attempt to reduce the level of Electromagnetic Interference caused by the
components whenever needed. Select Disabled to enhance system stability. The
options are Disabled and Enabled.
4-6
Chapter 4: AMI BIOS
Hyper-Threading (ALL)
Select Enable to use Intel Hyper-Threading Technology to enhance CPU performance. The options are Enable and Disable.
Cores Enabled
Use this feature to select the number of CPU cores to enable. Select 0 to enable
all cores.
Execute Disable Bit (Available if supported by the OS & the CPU)
Set to Enabled for Execute Disable Bit support which will allow the processor to
designate areas in the system memory where an application code can execute and
where it cannot, thus preventing a worm or a virus from flooding illegal codes to overwhelm the processor or damaging the system during a virus attack. The options are
Enable and Disable. (Refer to Intel and Microsoft websites for more information.)
PPIN Control
Select Unlock/Enable to use the Protected-Processor Inventory Number (PPIN) in
the system. The options are Unlock/Enable and Unlock/Disable.
Hardware Prefetcher (Available when supported by the CPU)
If this item is set to Enable, the hardware prefetcher will prefetch streams of data
and instructions from the main memory to the Level 2 (L2) cache to improve CPU
performance. The options are Disable and Enable.
Adjacent Cache Line Prefetch (Available when supported by the CPU)
Select Enable for the CPU to prefetch both cache lines for 128 bytes as comprised.
Select Disable for the CPU to prefetch both cache lines for 64 bytes. The options
are Disable and Enable.
Note: If there is any change to this setting, you will need to power off and
reboot the system for the change to take effect. Please refer to Intel’s
web site for detailed information.
DCU Streamer Prefetcher (Available when supported by the CPU)
If this item is set to Enable, the DCU (Data Cache Unit) streamer prefetcher will
prefetch data streams from the cache memory to the DCU (Data Cache Unit) to
speed up data accessing and processing for CPU performance enhancement. The
options are Disable and Enable.
4-7
X10SRL-F User’s Manual
DCU IP Prefetcher
If this item is set to Enable, the IP prefetcher in the DCU (Data Cache Unit) will
prefetch IP addresses to improve network connectivity and system performance.
The options are Enable and Disable.
DCU (Data Cache Unit) Mode
Use this item to set the DCU data-prefecting mode. The options are 32KB 8Way
Without ECC and 16KB 4Way With ECC.
Direct Cache Access (DCA)
Select Enable to use Intel DCA (Direct Cache Access) Technology to maximize efficiency in memory data transferring and accessing. The options are Auto, Enable
and Disable.
DCA Prefetch Delay
A DCA prefetcher is used with a TOE (TCP/IP Offload Engine) adapter to prefetch
data to shorten execution cycles and to maximize data processing efficiency.
Prefetching data too frequently can saturate the cache directory and delay necessary cache access. This feature reduces or increases the frequency of system data
prefetching activities. The options are Disable, [8], [16], [32], [40], [48], [56], [64],
[72], [80], [88], [96], [104], and [112].
X2APIC (Extended Advanced Programmable Interrupt Controller)
Based on the Intel Hyper-Threading technology, each logical processor (thread) is
assigned 256 APIC IDs (APIDs) in 8-bit bandwidth. When this item is set to Enable, the APIC ID will be expanded from 8 bits to 16 bits to provide 512 APIDs to
each thread to enhance CPU performance. The options are Disable and Enable.
AES-NI
Select Enable to use the Intel Advanced Encryption Standard (AES) New Instructions (NI) to ensure data security. The options are Enable and Disable.
Intel Virtualization Technology
Select Enable to use Intel Virtualization Technology so that I/O device assignments
will be reported directly to the VMM (Virtual Memory Management) through the
DMAR ACPI Tables. This feature offers fully-protected I/O resource-sharing across
the Intel platforms, providing the user with greater reliability, security and availability
in networking and data-sharing. The settings are Enable and Disable.
4-8
Chapter 4: AMI BIOS
Advanced Power Management Configuration
Power Technology
Select Energy Efficient to support power-saving mode. Select Custom to customize system power settings. Select Disabled to disable power-saving settings. The
options are Disable, Energy Efficient, and Custom.
Config TDP
Select Enable to allow the user to configure the Thermal Design Power (TDP)
settings for the system. The TDP refers to the maximum amount of power allowed
for running "real applications" without triggering an overheating event. The options
are Disable and Enable.
CPU P State Control
EIST (P-States)
EIST (Enhanced Intel SpeedStep Technology) allows the system to automatically adjust processor voltage and core frequency in an effort to reduce power
consumption and heat dissipation. Please refer to Intel’s website for detailed
information. The options are Disable and Enable.
Turbo Mode
Select Enable for processor cores to run faster than the frequency specified by
the manufacturer. The options are Disable and Enable.
P-state Coordination
Use this item to configure the processor's P-State coordination settings. During
a P-State, the voltage and frequency of the processor will be reduced when it is
in operation. This makes the processor more energy efficient, resulting in further
energy gains. The options are HW_ALL, SW_ALL and SW-ANY.
CPU C State Control
Package C State limit
Use this item to set the limit on the C-State package register. The options are
C0/1 state, C2 state, C6 (non-Retention) state, and C6 (Retention) state.
CPU C3 Report
Select Enable to allow the BIOS to report the CPU C3 State (ACPI C2) to the
operating system. During the CPU C3 State, the CPU clock generator is turned
off. The options are Enable and Disable.
4-9
X10SRL-F User’s Manual
CPU C6 Report (Available when Power Technology is set to Custom)
Select Enable to allow the BIOS to report the CPU C6 state (ACPI C3) to the
operating system. During the CPU C6 state, power to all caches is turned off.
The options are Enable and Disable.
Enhanced Halt State (C1E)
Select Enabled to enable "Enhanced Halt State" support, which will significantly
reduce the CPU's power consumption by minimizing CPU's clock cycles and
voltage use during a "Halt State." The options are Disable and Enable.
CPU T State Control
ACPI (Advanced Configuration Power Interface) T-States
If this item is set to Enable, CPU throttling will be supported by the operating
system to reduce power consumption. The options are Enable and Disable.
CPU Advance PM Tuning
Energy Perf (Performance) BIAS
Energy Performance Tuning
Select Enable for the AMI BIOS to handle energy-performance tuning on the
CPU. Select Disable for the operating system to handle CPU energy-performance tuning. The options are Disable and Enable.
Energy Performance Bias Setting
Use this feature to select an appropriate fan setting to achieve maximum system
performance (with maximum cooling) or maximum energy efficiency with maximum power saving). The fan speeds are controlled by the firmware management
via IPMI 2.0. The options are Performance, Balanced Performance, Balanced
Power, and Power.
Power/Performance Switch
Select Enable to activate the Power/Performance switch to allow the user to
select the power saving mode, which will slow down the system performance,
or to select the system performance mode, which will consume more power. The
options are Enable and Disable.
Workload Configuration
Use this feature to set the power management setting optimized for regular workload condition. The options are Balanced (recommended) and I/O sensitive.
4-10
Chapter 4: AMI BIOS
Averaging Time Window
Use this feature to set the effective window for the average of C0 and D0 time.
The default setting is 23.
P0 Total Time Threshold Low
Use this feature to set the low threshold below which the hardware switching
mechanism will disable the performance setting (0). The default setting is 35.
P0 Total Time Threshold High
Use this feature to set the high threshold above which the hardware switching
mechanism will enable the performance setting (0). The default setting is 58.
Socket RAPL (Running Average Power Limit) Config
FAST_RAPL_NSTRIKE_PL2_DUTY_CYCLE
This feature displays the value of the item above within the range between 25
(10%) and 64 (25%).
Turbo Power Limit Lock
Select Enable to set the power use limit for the machine when it is running in
the turbo mode. The options are Enable and Disable.
Long Power Limit Override
Select Enable to support long-term power limit override. If this feature is disabled,
BIOS will set the default value. The options are Enable and Disable.
Long Duration Power Limit
This item displays the power limit set by the user during which long duration
power is maintained. The default setting is 0.
Package Clamping Limit1
Use this item to set the limit on power performance states for the run-time processor, with P0 being the state with the highest frequency (clock speed) and power
(consumption), and P1, a step lower in performance than P0, with its frequency
and voltage scaled back a notch. The options are Between P1/P0 and Below P1.
Short Duration Power Limit Enable
Select Enable to support Short Duration Power Limit (Power Limit 2). The options
are Enable and Disable.
4-11
X10SRL-F User’s Manual
Short Duration Power Limit
This item displays the time period during which short duration power is maintained. The default setting is 0.
Package Clamping Limit2
Use this item to set the limit on power performance states for the processor
operating in turbo mode, with P0 being the state with the highest frequency
(clock speed) and power (consumption), and P1, a step lower in performance
than P0, with its frequency and voltage scaled back a notch. The options are
Between P1/P0 and Below P1.
Chipset Configuration
North Bridge
This feature allows the user to configure the settings for the Intel North Bridge.
IIO Configuration
EV DFX (Device Function On-Hide) Feature
When this feature is set to Enable, the EV_DFX Lock Bits that are located on a
processor will always remain clear during electric tuning. The options are Disable and Enable.
IIO1 Configuration
CPU SLOT3 PCI-E 3.0 X8
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are Gen 1 (2.5GT/s), Gen 2 (5 GT/s), and Gen 3 (8GT/s).
CPU SLOT2 PCI-E 3.0 X4 (IN X8)
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are Gen 1 (2.5GT/s), Gen 2 (5 GT/s), and Gen 3 (8GT/s).
CPU SLOT4 PCI-E 3.0 X8 (IN X16)
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are Gen 1 (2.5GT/s), Gen 2 (5 GT/s), and Gen 3 (8GT/s).
CPU SLOT5 PCI-E 3.0 X8
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are Gen 1 (2.5GT/s), Gen 2 (5 GT/s), and Gen 3 (8GT/s).
4-12
Chapter 4: AMI BIOS
CPU SLOT6 PCI-E 3.0 X8 (IN X16)
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are Gen 1 (2.5GT/s), Gen 2 (5 GT/s), and Gen 3 (8GT/s).
CPU SLOT7 PCI-E 3.0 X8
This item configures the PCI-E port Bifuraction setting for a PCI-E port specified
by the user. The options are Gen 1 (2.5GT/s), Gen 2 (5 GT/s), and Gen 3 (8GT/s).
IOAT Configuration
Enable I/OAT
Select Enable to enable Intel I/OAT (I/O Acceleration Technology), which significantly reduces CPU overhead by leveraging CPU architectural improvements
and freeing the system resource for other tasks. The options are Enable and
Disable.
No Snoop
Select Enable to support no-snoop mode for each CB device. The options are
Disable and Enable.
Relaxed Ordering
Select Enable to enable Relaxed Ordering support which will allow certain transactions to violate the strict-ordering rules of PCI and to be completed prior to
other transactions that have already been enqueued. The options are Disable
and Enable.
 Intel VT for Directed I/O (VT-d)
Intel® VT for Directed I/O (VT-d)
Select Enable to use Intel Virtualization Technology support for Direct I/O VT-d
support by reporting the I/O device assignments to the VMM (Virtual Machine
Monitor) through the DMAR ACPI Tables. This feature offers fully-protected I/O
resource sharing across Intel platforms, providing greater reliability, security and
availability in networking and data-sharing. The options are Enable and Disable.
Interrupt Remapping
Select Enable for Interrupt Remapping support to enhance system performance.
The options are Enable and Disable.
4-13
X10SRL-F User’s Manual
Coherency Support (Non-Isoch)
Select Enable for the Non-Iscoh VT-d engine to pass through DMA (Direct
Memory Access) to enhance system performance. The options are Enable and
Disable.
Coherency Support (Isoch)
Select Enable for the Iscoh VT-d engine to pass through ATS to enhance system
performance. The options are Enable and Disable.
QPI (Quick Path Interconnect) Configuration
QPI Status
The following information will display:
•Number of CPU
•Number of IIO
•Current QPI Link Speed
•Current QPI Link Frequency
•QPI Global MMIO Low Base/Limit
•QPI Global MMIO High Base/Limit
•QPI PCIe Configuration Base/Size
Link Speed Mode
Use this item to select the data transfer speed for QPI Link connections. The
options are Fast and Slow.
Link Frequency Select
Use this item to select the desired frequency for QPI Link connections. The options are 6.4GB/s, 8.0GB/s, 9.6GB/s, Auto, and Auto Limited.
Link L0p Enable
Select Enable for Link L0p support. The options are Enable, Auto, and Disable.
Link L1 Enable
Select Enable for Link L1 support. The options are Enable, Auto, and Disable.
4-14
Chapter 4: AMI BIOS
COD Enable (Available when the OS and the CPU support this feature)
Select Enabled for Cluster-On-Die support to enhance system performance in
cloud computing. The options are Enabled and Disabled.
Early Snoop (Available when the OS and the CPU support this feature)
Select Enabled for Early Snoop support to enhance system performance. The
options are Enable, Disable, and Auto.
Isoc Mode
Select Enabled for Isochronous support to meet QoS (Quality of Service) requirements. This feature is especially important for Virtualization Technology. The
options are Enable and Disable.
Memory Configuration
Enforce POR
Select Enable to enforce POR restrictions for DDR4 frequency and voltage
programming. The options are Enabled and Disabled.
Memory Frequency
Use this feature to set the maximum memory frequency for onboard memory
modules. The options are Auto, 1333, 1400, 1600, 1800, 1867, 2000, 2133,
2200, 2400, 2600, 2667, and Reserved (Do not select Reserved).
ECC Support
Select Enable to enable Error Checking & Correction (ECC) support for onboard
memory modules. The options are Auto, Enable and Disable.
Enhanced Log Parsing
Select Enable to enable Error Checking & Correction (ECC) support for onboard
memory modules. The options are Auto, Enable and Disable.
Data Scrambling
Select Enabled to enable data scrambling to enhance system performance and
data integrity. The options are Auto, Disabled and Enabled.
Enable ADR
Select Enabled for ADR (Automatic Diagnostic Repository) support to enhance
memory performance. The options are Enabled and Disabled.
4-15
X10SRL-F User’s Manual
DRAM RAPL (Running Average Power Limit) Baseline
Use this feature to set the run-time power-limit baseline for DRAM modules. The
options are Disable, DRAM RAPL Mode 0, and DRAM RAPL Mode 1.
Set Throttling Mode
Throttling improves reliability and reduces power consumption in the processor via automatic voltage control during processor idle states. The options are
Disabled and CLTT (Closed Loop Thermal Throttling).
Socket Interleave Below 4GB
Select Enabled for the memory above the 4G Address space to be split between
two sockets. The options are Enable and Disable.
Channel Interleaving
Use this item to set DIMM channel interleaving mood. The options are Auto,
1 Way Interleave, 2 Way Interleave, 3, Way Interleave, and 4 Way Interleave.
Rank Interleaving
Use this item to select a rank memory interleaving method. The options are Auto,
1 Way, 2 Way, 4, Way, and 8 Way.
A7 Mode
Select Enabled to support A7 (Addressing) Mode to improve memory performance. The options are Enable and Disable.
DIMM Information
This item displays the status of a DIMM module specified.
•DIMMA1
•DIMMA2
•DIMMB1
•DIMMB2
•DIMMC1
•DIMMC2
•DIMMD1
•DIMMD2
4-16
Chapter 4: AMI BIOS
Memory RAS (Reliability Availability Serviceability)
Configuration
Use this submenu to configure the following Memory RAS settings.
RAS Mode
Select Enable to enable RAS support to enhance reliability, availability and serviceability of onboard memory modules. The options are Enable and Disable.
Lockstep x4 DIMMs
Select Enable to enable Lockstep Technology support for x4 DIMM modules.
The options are Auto, Disabled, and Enabled.
Memory Rank Sparing
This item indicates if memory rank sparing is supported by the motherboard.
Memory rank sparing enhances system memory performance. The options are
Enabled and Disabled.
Patrol Scrub
Patrol Scrubbing is a process that allows the CPU to correct correctable memory
errors detected in a memory module and send the correction to the requestor
(the original source). When this item is set to Enable, the IO hub will read and
write back one cache line every 16K cycles if there is no delay caused by internal
processing. By using this method, roughly 64 GB of memory behind the IO hub
will be scrubbed every day. The options are Enable and Disable.
Patrol Scrub Interval
Use this item to specify the number of hours (between 0 to 24) required for the
system to complete a full patrol scrubbing. Enter 0 for patrol scrubbing to be
performed automatically. The default setting is 24.
Demand Scrub
Demand Scrubbing is a process that allows the CPU to correct correctable
memory errors found in a memory module. When the CPU or I/O issues a
demand-read command, and the read data from memory turns out to be a
correctable error, the error is corrected and sent to the requestor (the original
source). Memory is corrected as well. Select Enable to use Demand Scrubbing
for ECC memory correction. The options are Enable and Disable.
Device Tagging
Select Enable to support device tagging. The options are Disable and Enable.
4-17
X10SRL-F User’s Manual
South
Bridge
The following South Bridge information will display:\
•USB Configuration
•USB Module Version
•USB Devices
Legacy USB Support
Select Enabled to support onboard legacy USB devices. Select Auto to disable
legacy support if there are no legacy USB devices present. Select Disable to have
all USB devices available for EFI applications only. The options are Enabled,
Disabled and Auto.
XHCI Hand-Off
This is a work-around solution for operating systems that do not support XHCI (Extensible Host Controller Interface) hand-off. The XHCI ownership change should be
claimed by the XHCI driver. The settings are Enabled and Disabled.
EHCI Hand-Off
This item is for operating systems that do not support Enhanced Host Controller
Interface (EHCI) hand-off. When this item is enabled, EHCI ownership change will
be claimed by the EHCI driver. The settings are Enabled and Disabled.
USB Mass Storage Driver Support
Select Enabled for USB mass storage device support. The options are Disabled
and Enabled.
Port 60/64 Emulation
Select Enabled for I/O port 60h/64h emulation support, which in turn, will provide
complete legacy USB keyboard support for the operating systems that do not support legacy USB devices. The options are Disabled and Enabled.
USB 3.0 Support
Select Enabled for USB 3.0 support. The options are Disabled, Enabled and Auto.
EHCI1
Select Enabled to enable EHCI (Enhanced Host Controller Interface) support on
USB 2.0 connector #1 (-at least one USB 2.0 connector should be enabled for EHCI
support.) The options are Disabled and Enabled.
4-18
Chapter 4: AMI BIOS
EHCI2
Select Enabled to enable EHCI (Enhanced Host Controller Interface) support on
USB 2.0 connector #2 (-at least one USB 2.0 connector should be enabled for EHCI
support.) The options are Disabled and Enabled.
XHCI Pre-Boot Driver
Select Enabled to enable XHCI (Extensible Host Controller Interface) support on a
pre-boot drive specified by the user. The options are Enabled and Disabled.
XHCI Idle L1
Select Enabled for XHCI (Extensible Host Controller Interface) Idle Level 1 support on a USB 3.0 connector specified by the user. The options are Enabled and
Disabled.
PCH DMI ASPM
Select Enabled to enable ASPM (Active State Power Management) support for a
PCH DMI drive. The options are Disabled and Enabled.
SATA
Configuration
When this submenu is selected, the AMI BIOS automatically detects the presence
of the SATA devices that are supported by the Intel PCH chip and displays the
following items:
SATA Controller
This item enables or disables the onboard SATA controller supported by the Intel
PCH chip. The options are Enabled and Disabled.
Configure SATA as
Select IDE to configure a SATA drive specified by the user as an IDE drive. Select
AHCI to configure a SATA drive specified by the user as an AHCI drive. Select
RAID to configure a SATA drive specified by the user as a RAID drive. The options
are IDE, AHCI, and RAID.
*If the item above "Configure SATA as" is set to AHCI, the following items
will display:
Support Aggressive Link Power Management
When this item is set to Enabled, the SATA AHCI controller manages the power
usage of the SATA link. The controller will put the link in a low power mode during
extended periods of I/O inactivity, and will return the link to an active state when
I/O activity resumes. The options are Enabled and Disabled.
4-19
X10SRL-F User’s Manual
SATA Port 0~ Port 5
This item displays the information detected on the installed SATA drive on the
particular SATA port.
•Model number of drive and capacity
•Software Preserve Support
Port 0~ Port 5
Select Enabled to enable a SATA port specified by the user. The options are
Disabled and Enabled.
Port 0 ~ Port 5 Hot Plug
This feature designates the port specified for hot plugging. Set this item to Enabled for hot-plugging support, which will allow the user to replace a SATA disk
drive without shutting down the system. The options are Enabled and Disabled.
Port 0 ~ Port 5 Spin Up Device
On an edge detect from 0 to 1, set this item to allow the PCH to initialize the
device. The options are Enabled and Disabled.
Port 0 ~ Port 5 SATA Device Type
Use this item to specify if the SATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
*If the item above "Configure SATA as" is set to IDE, the following items
will display:
Serial ATA Port 0~ Port 5
This item indicates that a SATA port specified by the user is not installed or not
present.
Port 0 ~ Port 5 SATA Device Type (Available when a SATA port is
detected)
Use this item to specify if the SATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
4-20
Chapter 4: AMI BIOS
*If the item above "Configure SATA as" is set to RAID, the following items
will display:
Support Aggressive Link Power Management
When this item is set to Enabled, the SATA AHCI controller manages the power
usage of the SATA link. The controller will put the link in a low power mode during
extended periods of I/O inactivity, and will return the link to an active state when
I/O activity resumes. The options are Enabled and Disabled.
SATA RAID Option ROM/UEFI Driver
Select EFI to load the EFI driver for system boot. Select Legacy to load a legacy
driver for system boot. The options are Disabled, EFI, and Legacy.
Serial ATA Port 0~ Port 5
This item displays the information detected on the installed SATA drives on the
particular SATA port.
•Model number of drive and capacity
•Software Preserve Support
Port 0~ Port 5
Select Enabled to enable a SATA port specified by the user. The options are
Disabled and Enabled.
Port 0 ~ Port 5 Hot Plug
This feature designates this port for hot plugging. Set this item to Enabled for
hot-plugging support, which will allow the user to replace a SATA drive without
shutting down the system. The options are Enabled and Disabled.
Port 0 ~ Port 5 Spin Up Device
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRESET initialization to the device. The options are Enabled and Disabled.
Port 0 ~ Port 5 SATA Device Type
Use this item to specify if the SATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
4-21
X10SRL-F User’s Manual
sSATA
Configuration
When this submenu is selected, the AMI BIOS automatically detects the presence
of the SATA devices that are supported by the SCU controller and displays the
following items:
sSATA Controller
This item enables or disables the onboard SATA controller supported by the Intel
SCU chip. The options are Enabled and Disabled.
Configure sSATA as
Select IDE to configure an sSATA drive specified by the user as an IDE drive. Select
AHCI to configure an sSATA drive specified by the user as an AHCI drive. Select
RAID to configure an sSATA drive specified by the user as a RAID drive. The options are IDE, AHCI, and RAID.
*If the item above "Configure sSATA as" is set to AHCI, the following items
will display:
Support Aggressive Link Power Management
When this item is set to Enabled, the sSATA AHCI controller manages the power
usage of the sSATA link. The controller will put the link in a low power mode
during extended periods of I/O inactivity, and will return the link to an active state
when I/O activity resumes. The options are Enabled and Disabled.
sSATA Port 0~ Port 3
This item displays the information detected on the installed sSATA drives on the
particular sSATA port.
•Model number of drive and capacity
•Software Preserve Support
sSATA Port 0~ Port 3
Select Enabled to enable an sSATA port specified by the user. The options are
Disabled and Enabled.
sSATA Port 0 ~ Port 3 Hot Plug
This feature designates the sSATA port specified for hot plugging. Set this item
to Enabled for hot-plugging support, which will allow the user to replace an
sSATA disk drive without shutting down the system. The options are Enabled
and Disabled.
4-22
Chapter 4: AMI BIOS
sSATA Port 0 ~ Port 3 Spin Up Device
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRESET initialization to the device. The options are Enabled and Disabled.
Port 0 ~ Port 3 sSATA Device Type
Use this item to specify if the sSATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
*If the item above "Configure sSATA as" is set to IDE, the following items
will display:
sSATA Port 0~ Port 3
This item indicates that an sSATA port specified by the user is not installed or
not detected.
Port 0 ~ Port 3 sSATA Device Type (Available when a SATA port is
detected)
Use this item to specify if the sSATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
*If the item above "Configure sSATA as" is set to RAID, the following items
will display:
Support Aggressive Link Power Management
When this item is set to Enabled, the SATA AHCI controller manages the power
usage of the SATA link. The controller will put the link in a low power mode during
extended periods of I/O inactivity, and will return the link to an active state when
I/O activity resumes. The options are Enabled and Disabled.
sSATA RAID Option ROM/UEFI Driver
Select EFI to load the EFI driver for system boot. Select Legacy to load a legacy
driver for system boot. The options are Disabled, EFI, and Legacy.
sSATA Port 0~ Port 3
This item displays the information detected on the installed sSATA drives on the
particular sSATA port.
•Model number of drive and capacity
•Software Preserve Support
4-23
X10SRL-F User’s Manual
sSATA Port 0~ Port 3
Select Enabled to enable an sSATA port specified by the user. The options are
Disabled and Enabled.
sSATA Port 0 ~ Port 3 Hot Plug
This feature designates this port for hot plugging. Set this item to Enabled for
hot-plugging support, which will allow the user to replace an sSATA drive without
shutting down the system. The options are Enabled and Disabled.
sSATA Port 0 ~ Port 3 Spin Up Device
On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRESET initialization to the device. The options are Enabled and Disabled.
Port 0 ~ Port 3 sSATA Device Type
Use this item to specify if the sSATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk
Drive and Solid State Drive.
Server ME (Management Engine) Configuration
This feature displays the following system ME configuration settings.
•General ME Configuration
•Operational Firmware Version
•Recovery Firmware Version
•ME Firmware Features
•ME Firmware Status #1
•ME Firmware Status #2
•Current State
•Error Code
4-24
Chapter 4: AMI BIOS
PCIe/PCI/PnP Configuration
The following PCI information will be displayed:
•PCI Bus Driver Version
•PCI Devices Common Settings:
VGA Palette Snoop
Select Enabled to support VGA palette register snooping which will allow a PCI
card that does not contain its own VGA color palette to examine a video card palette and mimic it for proper color display. The options are Disabled and Enabled.
PCI AER (Advanced Error-Reporting) Support
Select Enabled to support Advanced Error-Reporting for onboard PCI devices. The
options are Disabled and Enabled.
Above 4G Decoding (Available if the system supports 64-bit PCI decoding)
Select Enabled to decode a PCI device that supports 64-bit in the space above 4G
Address. The options are Enabled and Disabled.
SR-IOV Support (Available if the system supports Single-Root
Virtualization)
Select Enabled for Single-Root IO Virtualization support. The options are Enabled
and Disabled.
Maximum Payload
Select Auto for the system BIOS to automatically set the maximum payload value
for a PCI-E device to enhance system performance. The options are Auto, 128
Bytes and 256 Bytes.
Maximum Read Request
Select Auto for the system BIOS to automatically set the maximum size for a read
request for a PCI-E device to enhance system performance. The options are Auto,
128 Bytes, 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.
ASPM Support
Use this item to set the Active State Power Management (ASPM) level for a PCI-E
device. Select Auto for the system BIOS to automatically set the ASPM level based
on the system configuration. Select Disabled to disable ASPM support. The options
are Disabled and Auto.
Warning: Enabling ASPM support may cause some PCI-E devices to fail!
4-25
X10SRL-F User’s Manual
MMIOHBase
Use this item to select the base memory size according to memory-address mapping for the IO hub. The base memory size must be between 4032G to 4078G. The
options are 56T, 48T, 24T, 512G, and 256G.\
MMIO High Size
Use this item to select the high memory size according to memory-address mapping
for the IO hub. The options are 256G, 128G, 512G, and 1024G.
PCH SLOT1 PCI-E 2.0 x4 (in x8) OPPROM, CPU SLOT2 PCI-E 3.0 x4 (in x8)
OPPROM, CPU SLOT3 PCI-E 3.0 x8 OPPROM, CPU SLOT4 PCI-E 3.0 x8 (in
x16) OPPROM, CPU SLOT5 PCI-E 3.0 x8 OPPROM, CPU SLOT6 PCI-E 3.0
x16 OPPROM, CPU SLOT7 PCI-E 3.0 x8 OPPROM,
Select Enabled to enable Option ROM support to boot the computer using a device installed on the slot specified by the user. The options are Disabled, Legacy
and EFI.
Onboard LAN Option ROM Type
Use this item to select the Onboard LAN Option ROM type. The options are Legacy
and EFI.
Onboard LAN1 Option ROM/Onboard LAN2 Option ROM
Use this option to select the type of device installed in LAN Port1 or LAN Port2
used for system boot. The default setting for LAN1 Option ROM is PXE, and the
default setting for LAN2 Option ROM is Disabled.
Onboard Video Option ROM
Use this item to select the Onboard Video Option ROM type. The options are
Legacy and EFI.
VGA Priority
Use this item to select the graphics device to be used as the primary video display
at bootup. The options are Onboard and Offboard.
Network Stack
Select Enabled to enable PXE (Preboot Execution Environment) or UEFI (Unified
Extensible Firmware Interface) for network stack support. The options are Enabled
and Disabled.
4-26
Chapter 4: AMI BIOS
Super
IO Configuration
Super IO Chip AST2400
Serial Port 1 Configuration/Serial Port 2 Configuration
Serial Port 1/Serial Port 2
Select Enabled to enable the onboard serial port specified by the user. The options
are Enabled and Disabled.
Device Settings
This item displays the base I/O port address and the Interrupt Request address of
a serial port specified by the user.
Change Port 1 Settings/Change Port 2 Settings
This feature specifies the base I/O port address and the Interrupt Request address
of Serial Port 1or Serial Port 2. Select Auto for the BIOS to automatically assign
the base I/O and IRQ address to a serial port specified.
The options for Serial Port 1 are Auto, (IO=3F8h; IRQ=4), (IO=3F8h; IRQ=3, 4, 5,
6, 7, 9, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12); (IO=3E8h; IRQ=3,
4, 5, 6, 7, 9, 10, 11, 12), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12).
The options for Serial Port 2 are Auto, (IO=3F8h; IRQ=4), (IO=3F8h; IRQ=3, 4, 5,
6, 7, 9, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12); (IO=3E8h; IRQ=3,
4, 5, 6, 7, 9, 10, 11, 12), and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12).
Serial Port 2 Attribute
Select SOL to use COM Port 2 as a Serial_Over_LAN (SOL) port for console redirectoin. The options are COM and SOL.
Serial
Port Console Redirection
COM 1 Console Redirection
Select Enabled to enable COM Port 1 for Console Redirection, which will allow a
client machine to be connected to a host machine at a remote site for networking.
The options are Enabled and Disabled.
*If the item above set to Enabled, the following items will become available
for configuration:
4-27
X10SRL-F User’s Manual
COM1 Console Redirection Settings
Terminal Type
This feature allows the user to select the target terminal emulation type for Console Redirection. Select VT100 to use the ASCII Character set. Select VT100+ to
add color and function key support. Select ANSI to use the Extended ASCII Character Set. Select VT-UTF8 to use UTF8 encoding to map Unicode characters
into one or more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.
Bits Per second
Use this item to set the transmission speed for a serial port used in Console
Redirection. Make sure that the same speed is used in the host computer and the
client computer. A lower transmission speed may be required for long and busy
lines. The options are 9600, 19200, 38400, 57600 and 115200 (bits per second).
Data Bits
Use this feature to set the data transmission size for Console Redirection. The
options are 7 (Bits) and 8 (Bits).
Parity
A parity bit can be sent along with regular data bits to detect data transmission
errors. Select Even if the parity bit is set to 0, and the number of 1's in data bits
is even. Select Odd if the parity bit is set to 0, and the number of 1's in data bits
is odd. Select None if you do not want to send a parity bit with your data bits
in transmission. Select Mark to add a mark as a parity bit to be sent along with
the data bits. Select Space to add a Space as a parity bit to be sent with your
data bits. The options are None, Even, Odd, Mark and Space.
Stop Bits
A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard
serial data communication. Select 2 Stop Bits if slower devices are used. The
options are 1 and 2.
Flow Control
Use this item to set the flow control for Console Redirection to prevent data
loss caused by buffer overflow. Send a "Stop" signal to stop sending data when
the receiving buffer is full. Send a "Start" signal to start sending data when the
receiving buffer is empty. The options are None and Hardware RTS/CTS.
VT-UTF8 Combo Key Support
Select Enabled to enable VT-UTF8 Combination Key support for ANSI/VT100
terminals. The options are Enabled and Disabled.
4-28
Chapter 4: AMI BIOS
Recorder Mode
Select Enabled to capture the data displayed on a terminal and send it as text
messages to a remote server. The options are Disabled and Enabled.
Resolution 100x31
Select Enabled for extended-terminal resolution support. The options are Disabled and Enabled.
Legacy OS Redirection Resolution
Use this item to select the number of rows and columns used in Console Redirection for legacy OS support. The options are 80x24 and 80x25.
Putty KeyPad
This feature selects Function Keys and KeyPad settings for Putty, which is a
terminal emulator designed for the Windows OS. The options are VT100, LINUX,
XTERMR6, SCO, ESCN, and VT400.
Redirection After BIOS Post
Use this feature to enable or disable legacy Console Redirection after BIOS
POST. When set to Bootloader, legacy Console Redirection is disabled before
booting the OS. When set to Always Enable, legacy Console Redirection remains
enabled when booting the OS. The options are Always Enable and Bootloader.
SOL/COM2
SOL/COM2 Console Redirection
Select Enabled to use the SOL port for Console Redirection. The options are Enabled and Disabled.
*If the item above set to Enabled, the following items will become available
for user's configuration:
SOL/COM2 Console Redirection Settings
Use this feature to specify how the host computer will exchange data with the client
computer, which is the remote computer used by the user.
Terminal Type
Use this feature to select the target terminal emulation type for Console Redirection. Select VT100 to use the ASCII Character set. Select VT100+ to add color
and function key support. Select ANSI to use the Extended ASCII Character Set.
Select VT-UTF8 to use UTF8 encoding to map Unicode characters into one or
more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.
4-29
X10SRL-F User’s Manual
Bits Per second
Use this feature to set the transmission speed for a serial port used in Console
Redirection. Make sure that the same speed is used in the host computer and the
client computer. A lower transmission speed may be required for long and busy
lines. The options are 9600, 19200, 38400, 57600 and 115200 (bits per second).
Data Bits
Use this feature to set the data transmission size for Console Redirection. The
options are 7 (Bits) and 8 (Bits).
Parity
A parity bit can be sent along with regular data bits to detect data transmission
errors. Select Even if the parity bit is set to 0, and the number of 1's in data bits
is even. Select Odd if the parity bit is set to 0, and the number of 1's in data bits
is odd. Select None if you do not want to send a parity bit with your data bits
in transmission. Select Mark to add a mark as a parity bit to be sent along with
the data bits. Select Space to add a Space as a parity bit to be sent with your
data bits. The options are None, Even, Odd, Mark and Space.
Stop Bits
A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard
serial data communication. Select 2 Stop Bits if slower devices are used. The
options are 1 and 2.
Flow Control
Use this feature to set the flow control for Console Redirection to prevent data
loss caused by buffer overflow. Send a "Stop" signal to stop sending data when
the receiving buffer is full. Send a "Start" signal to start sending data when the
receiving buffer is empty. The options are None and Hardware RTS/CTS.
VT-UTF8 Combo Key Support
Select Enabled to enable VT-UTF8 Combination Key support for ANSI/VT100
terminals. The options are Enabled and Disabled.
Recorder Mode
Select Enabled to capture the data displayed on a terminal and send it as text
messages to a remote server. The options are Disabled and Enabled.
Resolution 100x31
Select Enabled for extended-terminal resolution support. The options are Disabled and Enabled.
4-30
Chapter 4: AMI BIOS
Legacy OS Redirection Resolution
Use this feature to select the number of rows and columns used in Console
Redirection for legacy OS support. The options are 80x24 and 80x25.
Putty KeyPad
This feature selects Function Keys and KeyPad settings for Putty, which is a
terminal emulator designed for the Windows OS. The options are VT100, LINUX,
XTERMR6, SCO, ESCN, and VT400.
Redirection After BIOS Post
Use this feature to enable or disable legacy Console Redirection after BIOS
POST. When set to Bootloader, legacy Console Redirection is disabled before
booting the OS. When set to Always Enable, legacy Console Redirection remains
enabled when booting the OS. The options are Always Enable and Bootloader.
Serial Port for Out-of-Band Management/Windows Emergency Management
Services (EMS)
The submenu allows the user to configure Console Redirection settings to support
Out-of-Band Serial Port management.
EMS (Emergency Management Services) Console Redirection
Select Enabled to use a COM port selected by the user for EMS Console Redirection. The options are Enabled and Disabled.
*If the item above set to Enabled, the following items will become available
for user's configuration:
EMS
Console Redirection Settings
This feature allows the user to specify how the host computer will exchange
data with the client computer, which is the remote computer used by the user.
Out-of-Band Management Port
The feature selects a serial port in a client server to be used by the Microsoft
Windows Emergency Management Services (EMS) to communicate with a remote host server. The options are COM1 and COM2/SOL.
Terminal Type
Use this feature to select the target terminal emulation type for Console Redirection. Select VT100 to use the ASCII character set. Select VT100+ to add color
and function key support. Select ANSI to use the extended ASCII character set.
Select VT-UTF8 to use UTF8 encoding to map Unicode characters into one or
more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.
4-31
X10SRL-F User’s Manual
Bits Per Second
This item sets the transmission speed for a serial port used in Console Redirection. Make sure that the same speed is used in the host computer and the client
computer. A lower transmission speed may be required for long and busy lines.
The options are 9600, 19200, 57600, and 115200 (bits per second).
Flow Control
Use this item to set the flow control for Console Redirection to prevent data
loss caused by buffer overflow. Send a "Stop" signal to stop sending data when
the receiving buffer is full. Send a "Start" signal to start sending data when
the receiving buffer is empty. The options are None, Hardware RTS/CTS, and
Software Xon/Xoff.
The setting for each these features is displayed:
Data Bits, Parity, Stop Bits
Trusted Computing (Available when a TPM device is
installed and detected by the BIOS)
Configuration
Security Device Support
If this feature and the TPM jumper on the motherboard are both set to Enabled,
onboard security devices will be enabled for TPM support to enhance data integrity
and network security. Please reboot the system for a change on this setting to take
effect. The options are Enabled and Disabled.
TPM State
Select Enabled to use TPM (Trusted Platform Module) settings to enhance system
data security. Please reboot your system for any change on the TPM state to take
effect. The options are Disabled and Enabled.
Pending Operation
Use this item to schedule a TPM-related operation to be performed by a security
device for system data integrity. Your system will reboot to carry out a pending TPM
operation. The options are 0, Enable Take Ownership, Disable Take Ownership,
and TPM Clear.
Note: Your system will reboot to carry out a pending TPM operation.
Current Status Information
This item displays the status of the TPM support on this motherboard.
4-32
Chapter 4: AMI BIOS
ACPI
Settings
WHEA Support
Select Enabled to support the Windows Hardware Error Architecture (WHEA) platform and provide a common infrastructure for the system to handle hardware errors
within the Windows OS environment to reduce system crashes and to enhance
system recovery and health monitoring. The options are Enabled and Disabled.
High Precision Timer
Select Enabled to activate the High Precision Event Timer (HPET) that produces
periodic interrupts at a much higher frequency than a Real-time Clock (RTC) does in
synchronizing multimedia streams, providing smooth playback and reducing the dependency on other timestamp calculation devices, such as an x86 RDTSC Instruction embedded in the CPU. The High Performance Event Timer is used to replace
the 8254 Programmable Interval Timer. The options are Enabled and Disabled.
NUMA
This feature enables the Non-Uniform Memory Access ACPI support. The options
are Enabled and Disabled.
4-33
X10SRL-F User’s Manual
4-4 Event Logs
Use this feature to configure Event Log settings.
Change SMBIOS Event Log Settings
This feature allows the user to configure SMBIOS Event settings.
Enabling/Disabling Options
SMBIOS Event Log
Select Enabled to enable SMBIOS (System Management BIOS) Event Logging
during system boot. The options are Enabled and Disabled.
Runtime Error Logging Support
Select Enabled to support Runtime Error Logging. The options are Enable and Disable. If this item is set to Enable, the following item will be available for configuration:
Memory Corrected Error Enabling (Available when the item above-Runtime
Error Logging Support is set to Enable)
Select Enable for the BIOS to correct a memory error if it is correctable. The options
are Enable and Disable.
PCI-Ex (PCI-Express) Error Enable
Select Yes for the BIOS to correct errors occurred in the PCI-E slots. The options
are Yes and No.
4-34
Chapter 4: AMI BIOS
Memory Correctable Error Threshold
Use this item to enter the threshold value for correctable memory errors. The default
setting is 10.
Erasing Settings
Erase Event Log
Select Enabled to erase all error events in the SMBIOS (System Management BIOS)
log before an event logging is initialized at bootup. The options are No and Yes.
When Log is Full
Select Erase Immediately to immediately erase all errors in the SMBIOS event log
when the event log is full. Select Do Nothing for the system to do nothing when
the SMBIOS event log is full. The options are Do Nothing and Erase Immediately.
SMBIOS Event Log Standard Settings
Log System Boot Event
Select Enabled to log system boot events. The options are Disabled and Enabled.
MECI (Multiple Event Count Increment)
Enter the increment value for the multiple event counter. Enter a number between
1 to 255. The default setting is 1.
METW (Multiple Event Count Time Window)
This item is used to determine how long (in minutes) should the multiple event
counter wait before generating a new event log. Enter a number between 0 to 99.
The default setting is 60.
Note: Please reboot the system for the changes to take effect.
View System Event Log
This item allows the user to view the event in the system event log. Select this item
and press <Enter> to view the status of an event in the log.
Date/Time/Sensor/Type
4-35
X10SRL-F User’s Manual
4-5 IPMI
Use this feature to configure Intelligent Platform Management Interface (IPMI)
settings.
IPMI Firmware Revision
This item indicates the IPMI firmware revision used in your system.
IPMI Status
This item indicates the status of the IPMI firmware installed in your system.
System Event Log
Enabling/Disabling Options
SEL Components
Select Enabled for all system event logging at bootup. The options are Enabled
and Disabled.
Erasing Settings
Erase SEL
Select Yes, On next reset to erase all system event logs upon next system reboot.
Select Yes, On every reset to erase all system event logs upon each system reboot.
Select No to keep all system event logs after each system reboot. The options are
No, Yes, On next reset, and Yes, On every reset.
4-36
Chapter 4: AMI BIOS
When SEL is Full
This feature allows the user to determine what the BIOS should do when the system event log is full. Select Erase Immediately to erase all events in the log when
the system event log is full. The options are Do Nothing and Erase Immediately.
Note: After making changes on a setting, be sure to reboot the system for
the changes to take effect.
BMC Network Configuration
The following items will be displayed:
IPMI LAN Selection
This item displays the IPMI LAN setting. The default setting is Failover.
IPMI Network Link Status
This item displays the IPMI Network Link status. The default setting is Shared LAN.
Update IPMI LAN Configuration
Select Yes for the BIOS to implement all IP/MAC address changes at the next
system boot. The options are No and Yes
Configuration Address Source
Use this item to select the source of the IP address for this computer. If Static is
selected, you will need to know the IP address of this computer and enter it to the
system manually in the field. If DHCP is selected, the BIOS will search for a DHCP
(Dynamic Host Configuration Protocol) server in the network that is attached to
and request the next available IP address for this computer. The options are DHCP
and Static.
The following items are assigned IP addresses automatically if DHCP is selected,
or they can be configured manually if Static is selected.
Station IP Address
This item displays the Station IP address for this computer. This should be in decimal
and in dotted quad form (i.e., 192.168.10.253).
Subnet Mask
This item displays the sub-network that this computer belongs to. The value of each
three-digit number separated by dots should not exceed 255.
Station MAC Address
This item displays the Station MAC address for this computer. Mac addresses are
6 two-digit hexadecimal numbers.
4-37
X10SRL-F User’s Manual
Gateway IP Address
This item displays the Gateway IP address for this computer. This should be in
decimal and in dotted quad form (i.e., 192.168.10.253).
4-38
Chapter 4: AMI BIOS
4-6Security
This menu allows the user to configure the following security settings for the
system.
Password Check
Select Setup for the system to check for a password at Setup. Select Always for the
system to check for a password at bootup or upon entering the BIOS Setup utility.
The options are Setup and Always.
Administrator Password
Use this feature to set the administrator password which is required to enter the
BIOS setup utility. The length of the password should be from 3 characters to 20
characters long.
4-39
X10SRL-F User’s Manual
4-7Boot
Use this feature to configure Boot Settings:
Setup Prompt Timeout
Use this item to indicate the length of time (the number of seconds) for the BIOS to
wait before rebooting the system when the setup activation key is pressed. Enter the
value of 65535 (0xFFFF) for the BIOS to wait indefinitely. The default setting is 1.
Boot Mode Select
Use this item to select the type of device that the system is going to boot from. The
options are Legacy, UEFI, and Dual. The default setting is Dual.
Fixed Boot Order Priorities
This option prioritizes the order of bootable devices that the system to boot from.
Press <Enter> on each entry from top to bottom to select devices.
•Dual Boot Order #1
•Dual Boot Order #2
•Dual Boot Order #3
•Dual Boot Order #4
•Dual Boot Order #5
•Dual Boot Order #6
•Dual Boot Order #7
4-40
Chapter 4: AMI BIOS
•Dual Boot Order #8
•Dual Boot Order #9
•Dual Boot Order #10
•Dual Boot Order #11
•Dual Boot Order #12
•Dual Boot Order #13
•Dual Boot Order #14
•Dual Boot Order #15
Delete Boot Option
Use this item to select a boot device to delete from the boot priority list.
Delete Boot Option
Select the target boot device to delete.
Hard Disk Drive BBS Priorities
•Boot Order #1 - This feature sets the system boot order of detected devices.
The options are [the list of detected boot device(s)] and Disabled.
Network Drive BBS Priorities
•Boot Order #1 - This feature sets the system boot order of detected devices.
The options are [the list of detected boot device(s)] and Disabled.
UEFI Application Boot Priorities
•Boot Order # - This feature sets the system boot order of detected devices. The
options are [the list of detected boot device(s)] and Disabled. 1
4-41
X10SRL-F User’s Manual
4-8 Save & Exit
Select the Save & Exit tab from the BIOS setup screen to configure the settings
below.
Discard Changes and Exit
Select this option to quit the BIOS setup without making any permanent changes
to the system configuration, and reboot the computer. Select Discard Changes and
Exit from the Exit menu and press <Enter>.
Save Changes and Reset
When you have completed the system configuration changes, select this option to
leave the BIOS setup utility and reboot the computer for the new system configuration parameters can take effect. Select Save Changes and Exit from the Exit menu
and press <Enter>.
Save Options
Save Changes
When you have completed the system configuration changes, select this option to
save all changes made. This will not reset (reboot) the system.
Discard Changes
Select this option and press <Enter> to discard all the changes and return to the
AMI BIOS Utility Program.
Restore Defaults
To set this feature, select Restore Defaults from the Exit menu and press <Enter>.
These are factory settings designed for maximum system performance but not for
maximum stability.
4-42
Chapter 4: AMI BIOS
Save As User Defaults
To set this feature, select Save as User Defaults from the Exit menu and press <Enter>. This enables the user to save any changes to the BIOS setup for future use.
Restore User Defaults
To set this feature, select Restore User Defaults from the Exit menu and press <Enter>. Use this feature to retrieve user-defined settings that were saved previously.
Boot Override
This feature allows the user to override the Boot Option Priorities sequence in the
Boot menu, and immediately boot the system with another device specified by the
user. This is a one-time override.
4-43
X10SRL-F User’s Manual
Notes
4-44
Appendix A: POST Error Beep Codes
Appendix A
BIOS Error Beep Codes
During the POST (Power-On Self-Test) routines, which are performed each time
the system is powered on, errors may occur.
Non-fatal errors are those which, in most cases, allow the system to continue
with bootup. The error messages normally appear on the screen.
Fatal errors will not allow the system to continue to bootup. If a fatal error occurs, you should consult with your system manufacturer for possible repairs.
These fatal errors are usually communicated through a series of audible beeps.
The numbers on the fatal error list correspond to the number of beeps for the
corresponding error.
A-1 BIOS Error Beep Codes
BIOS Error Beep Codes
Beep Code/LED
Error Message
Description
1 beep
Refresh
Circuits have been reset.
(Ready to power up)
5 short beeps + 1 long
beep
Memory error
No memory detected in the
system
8 beeps
Display memory
read/write error
Video adapter missing or with
faulty memory
OH LED On
System OH
System Overheat
A-1
X10SRL-F User’s Manual
Notes
A-2
Appendix B: Software Installation Instructions
Appendix B
Software Installation Instructions
B-1 Installing Software Programs
The Supermicro ftp site contains drivers and utilities for your system at ftp://ftp.
supermicro.com. Some of these must be installed, such as the chipset driver.
After accessing the ftp site, go into the CDR_Images directory and locate the ISO
file for your motherboard. Download this file to create a CD/DVD of the drivers and
utilities it contains. (You may also use a utility to extract the ISO file if preferred.)
Another option is to go to the Supermicro Website at http://www.supermicro.com/
products/. Find the product page for your motherboard here, where you may download individual drivers and utilities.
After creating a CD/DVD with the ISO files, insert the disk into the CD/DVD drive
on your system and the display shown below should appear.
Driver/Tool Installation Display Screen
Note 1: Click the icons showing a hand writing on paper to view the
readme files for each item. Click the computer icons to the right of these
items to install each item (from top to the bottom) one at a time. After
installing each item, you must re-boot the system before moving on
to the next item on the list. The bottom icon with a CD on it allows you
to view the entire contents.
Note 2: When making a storage driver diskette by booting into a Driver
CD, please set the SATA Configuration to "Compatible Mode" and configure
SATA as IDE in the BIOS Setup. After making the driver diskette, be sure
to change the SATA settings back to your original settings.
B-1
X10SRL-F Motherboard User’s Manual
B-2 Installing SuperDoctor5
The Supermicro SuperDoctor® 5 is a hardware monitoring program that functions in
a command-line or web-based interface in Windows and Linux operating systems.
The program monitors system health information such as CPU temperature, system
voltages, system power consumption, fan speed, and provides alerts via email or
Simple Network Management Protocol (SNMP).
SuperDoctor 5 comes in local and remote management versions and can be used
with Nagios to maximize your system monitoring needs. With SuperDoctor 5 Management Server (SSM Server), you can remotely control power on/off and reset
chassis intrusion for multiple systems with SuperDoctor 5 or IPMI. SD5 Management Server monitors HTTP, FTP, and SMTP services to optimize the efficiency of
your operation.
Note: The default User Name and Password for SuperDoctor 5 is admin
/admin.
SuperDoctor 5 Interface Display Screen (Health Information)
Note: The SuperDoctor 5 program and User’s Manual can be downloaded
from the Supermicro web site at http://www.supermicro.com/products/nfo/
sms_sd5.cfm.
B-2
Appendix C: UEFI BIOS Recovery
Appendix C
UEFI BIOS Recovery Instructions
Warning: Do not upgrade the BIOS unless your system has a BIOS-related issue.
Flashing the wrong BIOS can cause irreparable damage to the system. In no event shall
Supermicro be liable for direct, indirect, special, incidental, or consequential damages
arising from a BIOS update. If you need to update the BIOS, do not shut down or reset
the system while the BIOS is updating to avoid possible boot failure.
C-1 An Overview to the UEFI BIOS
The Unified Extensible Firmware Interface (UEFI) specification provides a softwarebased interface between the operating system and the platform firmware in the
pre-boot environment. The UEFI specification supports an architecture-independent
mechanism for add-on card initialization to allow the UEFI OS loader, which is stored
in the add-on card, to boot up the system. UEFI offers a clean, hands-off control
to a computer system at bootup.
C-2 How to Recover the UEFI BIOS Image
A UEF BIOS flash chip consists of a recovery BIOS block, comprised of two boot
blocks and a main BIOS block (a main BIOS image). The boot block contains critical
BIOS codes, including memory detection and recovery codes for the user to flash
a new BIOS image if the original main BIOS image is corrupted. When the system
power is on, the boot block codes execute first. Once that is completed, the main
BIOS code will continue with system initialization and bootup.
Note: Follow the BIOS Recovery instructions below for BIOS recovery
when the main BIOS boot crashes. However, when the BIOS boot block
crashes, you will need to follow the procedures in Appendix D.
C-3 To Recover the Main BIOS Block Using a USBAttached Device
This feature allows the user to recover a BIOS image using a USB-attached device
without additional utilities used. A USB flash device such as a USB Flash Drive, or
a USB CD/DVD ROM/RW device can be used for this purpose. However, a USB
Hard Disk drive cannot be used for BIOS recovery at this time.
To perform UEFI BIOS recovery using a USB-attached device, follow the instructions below.
C-1
X10SRL-F User’s Manual
1. Using a different machine, copy the "Super.ROM" binary image file into the
disc Root "\" Directory of a USB device or a writeable CD/DVD.
Note: If you cannot locate the "Super.ROM" file in your driver disk, visit
our website at www.supermicro.com to download the BIOS image into
a USB flash device and rename it "Super ROM" for BIOS recovery use.
2. Insert the USB device that contains the new BIOS image ("Super.ROM") into
your USB drive and power on the system
3. While powering on the system, keep pressing <Ctrl> and <Home> simultaneously on your keyboard until your hear two short beeps. This may take from a
few seconds to one minute.
4. After locating the new BIOS binary image, the system will enter the BIOS
Recovery menu as shown below.
Note: At this point, you may decide if you want to start with BIOS Recovery. If you decide to proceed with BIOS Recovery, follow the procedures
below.
5. When the screen as shown above displays, using the arrow key, select the
item- "Proceed with flash update" and press the <Enter> key. You will see the
progress of BIOS Recovery as shown in the screen below.
Note: Do not interrupt the process of BIOS flashing until it is completed.
C-2
Appendix C: UEFI BIOS Recovery
6. After the process of BIOS Recovery is complete, press any key to reboot the
system.
7. Using a different system, extract the BIOS package into a bootable USB flash
drive.
8. When a DOS prompt appears, enter FLASH.BAT BIOSname.### at the
prompt.
Note: Do not interrupt this process until BIOS flashing is completed.
C-3
X10SRL-F User’s Manual
9. After seeing the message that BIOS update is completed, unplug the AC power cable from the power supply to clear CMOS, and then plug the AC power
cable in the power supply again to power on the system.
10.Press <Del> continuously to enter the BIOS Setup utility.
11. Press <F3> to load default settings.
12.After loading default settings, press <F4> to save the settings and exit the
BIOS Setup utility.
C-4
Appendix D: Dual Boot Block
Appendix D
Dual Boot Block on Grantley Platforms
Overview
On X10 Grantley platforms, Supermicro introduces the Dual Boot Block feature that
revives the system from an inert state if the primary boot block in the ROM chip
is damaged. A boot block carries critical codes to boot the system with minimum
hardware requirements for the BIOS recovery flash.
In the previous generation platforms, there is an onboard jumper called JBR1 to
activate the secondary boot block in the ROM chip. However, it is not convenient
for data centers and enterprises.
This document describes how to enable the BIOS recovery flash by using the Dual
Boot Block feature through IPMI GUI browser and IPMI Command Sets on the X10
Grantley platforms.
Before Startup
A USB flash drive with FAT32 file system and Super.ROM stored are required, and
the USB flash drive does not need to be bootable. IPMI firmware that is capable of
supporting BIOS Resilience function in IPMI browser and of mounting virtual media
via OEM CMDs is required, too. The SMCIPMITool is needed if Dual Boot Block is
activated by IPMI Command Sets as stated in Section D-2.
When to Use Dual Boot Block
The primary dual block can get corrupted when it is flashing and encounters a power
outage. The system does not respond nor output video at all after power-on. The
secondary boot block can be activated to kick in the BIOS recovery flash.
How to Use Dual Boot Block
Two methods on how to use the Dual Boot Block feature are introduced in the
following pages:
1. Through the IPMI GUI Browser
2. Through the IPMI Command Sets
These are user-attended operations. IPMI logic on the defective system has to be
alive and functioning. IPMI IP is known to the user.
D-1
X10SRL-F User’s Manual
D-1 IPMI GUI Browser
To perform perform the Dual Boot Block through the IPMI GUI browser, follow the
instructions below:
1. After the IPMI GUI browser log-in, click on the Miscellaneous tab, then BIOS
Resilience, then the Resile button.
2. IPMI prints out a message that indicates the secondary boot block activation.
If the system is on, IPMI forces it to shut down.
D-2
Appendix D: Dual Boot Block
3. Click on the Remote Control tab, then Console Redirection, then the Launch
Console button to open the Java iKVM Viewer.
4. In the Java iKVM Browser, click on the Virtual Media tab, then Virtual Storage to open the Virtual Media Loader.
D-3
X10SRL-F User’s Manual
5. In the Virtual Media loader, click on the Device1 tab, then Logical Drive
Type drop-down menu, then select the USB flash drive with Super.ROM.
Click Plug In, then OK.
6. Click on the Remote Control tab, then Power Control, then check the
Power On Server button. Click on the Perform Action button to power up
the system.
D-4
Appendix D: Dual Boot Block
7. After the system powers on, the secondary boot block starts to initialize the
essential hardware components and locates Super.ROM in the USB flash
drive, which was mounted earlier. If Super.ROM is found, the on-duty boot
block boots to it and finishes the rest of the POST processes. The system
will automatically enter the BIOS recovery flash page in Setup at the end of
POST. Move the cursor to Proceed with flash update and press ENTER.
8. The BIOS recovery flash begins and programs the boot blocks as well as the
main block.
D-5
X10SRL-F User’s Manual
9. A message box will appear to indicate the BIOS recovery flash process is
complete. Press ENTER to finish. The system will do a power cycle to deactivate the dual boot block feature and produce a normal BIOS POST.
D-6
Appendix D: Dual Boot Block
D-2 IPMI Command Sets
To perform perform the Dual Boot Block through the IPMI Command Sets, follow
the instructions below:
1. After the IPMI GUI browser log-in, click on the Remote Control tab, then
Console Redirection, then the Launch Console button to open Java iKVM
Viewer.
2. Open a DOS command prompt for SMCIIPMITool execution. Type ipmi
power down to power off the defective system.
D-7
X10SRL-F User’s Manual
3. Enable BIOS Resilience mode in remote IPMI and confirm.
•To enable, type the following command in the command prompt:
ipmi raw 30 70 C2 D5 00 00
•To confirm, type the following command in the command prompt:
impi raw 30 70 C3 D5
4. Mount the USB flash drive with Super.ROM to remote Virtual Media Device 1.
This must de done in the IPMI Shell mode.
•To enter the IPMI Shell mode, type: shell
•To see the list of drives, type: vmwa dev1list
•To mount the drive, type: vmwa dev1drv 2. In this example, the USB flash drive is drive #2 (drv 2). Drive numbers may
vary in each system.
•To confirm if the drive is mounted, type: vmwa status
D-8
Appendix D: Dual Boot Block
5. Power on the remote system for BIOS recovery flash.
•To power on, type: ipmi power up
After the system powers on, the secondary boot block initializes the essential
hardware components and locates Super.ROM in the USB flash drive, which are
the same as Steps 7-9 in Section D-1.
User Approach
Dual Boot Block is not designed for an automatic operation, non user-attended operation. The feature offers an immediate resilience after a BIOS upgrade somehow
stops upon flashing the on-duty boot block. For a BIOS upgrade on multi-node, SUM
is recommended. Please contact your Field Application Engineer representative for
an understanding of the SUM product.
D-9
X10SRL-F User’s Manual
Notes
D-10
(Disclaimer Continued)
The products sold by Supermicro are not intended for and will not be used in life support systems,
medical equipment, nuclear facilities or systems, aircraft, aircraft devices, aircraft/emergency communication devices or other critical systems whose failure to perform be reasonably expected to result
in significant injury or loss of life or catastrophic property damage. Accordingly, Supermicro disclaims
any and all liability, and should buyer use or sell such products for use in such ultra-hazardous applications, it does so entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend
and hold Supermicro harmless for and against any and all claims, demands, actions, litigation, and
proceedings of any kind arising out of or related to such ultra-hazardous use or sale.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising