ModLink Advanced Fiber Optic Cables

ModLink Advanced Fiber Optic Cables
ModLink Advanced
Fiber Optic Cables
FEATURES AND SPECIFICATIONS
Features and Benefits
Molex Plug and Play Advanced FIber Optic Systems
offer premium factory-controlled optical performance,
enable flexible system configuration and fast,
economical installation. ModLink is ideal for missioncritical applications such as Data Centers and Storage
Area Networks, applications where fast installation is
paramount and environments where moves adds and
changes are frequent or managed in-house.
ModLink Cable Features
 Round, flexible outer jacket is easy to bend, route
and install
 Available in Plenum (OFNP) and LSZH constructions
 Industry-leading low insertion loss (0.50dB Maximum Insertion Loss for Laser Optimized OM3 Cables)
 Cables available in 12 fiber constructions
 ModLink Advanced Fiber Optic Cables are 100%
tested
 Pulling eyes installed to protect the assembly during
installation
Applications
Modlink systems are designed to support a variety of
high-speed network topologies including:
IEEE 802.3 10GBase-SR/SW
10Gbps
IEEE 802.3 10Gbase-LX4
10Gbps
Fibre Channel 400-M5-SN-1
4Gbps
Fibre Channel 1200-M5E-SN1
10Gbps
Fibre Channel FC-PH
1Gbps
IEEE 802.3 1000Base-SX/LX
1Gbps
FDDI
100Mbps
IEEE 802.3 FOIRL
10Mbps
IEEE 802.3 10Base-F
10Mbps
ATM 155 Mbps, 622 Mbps, 1.2 Gbps. 2.4 Gbps
Commercial Standards
International
ISO/IEC 11801
North American
ANSI/TIA/EIA-568.B.3-2000
ANSI/TIA/EIA-492
Telecordia GR-409
ICEA S-596
Technical Information
Maximum Insertion Loss:
Laser Optimized OM3
0.50 dB
OM1, OM2, OS1 Cables
0.50 dB
Attenuation:
Multimode OM1, OM2, OM3 3.5dB@850nm/
1.2dB@1300nm
Single Mode OS1
0.50dB@1310nm or 1550nm
Durability
500 Cycles
Guide Pin Retention
3 lbs
Nominal Outside Diameter
4.5 mm (0.177 in)
Cable Weight
19 kg/km
(12.8 lb/kft)
Minimum Bend Radius Install 2.5 in (6.35cm)
Minimum Bend Radius Long Term 1.25 in (3.18cm)
Maximum Long Term Tensile Load 90 lbf (440 N)
Operating Temp
-0º to 70ºC
(32ºF to 158ºF)
Storage Temp
-40º to 70ºC
(-40ºF to 158ºF)
Installation Temp
-0º to 70ºC
(32ºF to 158ºF)
Jacket Colors:
Multimode 62.5µ OM1 & 50µ OM2 Orange
Laser Optimized 50µ OM3 (10G)
Aqua
Single Mode
Yellow
Fiber Specification
Fiber Type
ISO
Classification
Bandwidth
(MHz/km)
62.5/125µ*
OM1
200/500
50/125µ*
OM2
500/500
50/125µ**
OM3
2000/500
Singlemode
OS1
N/A
*Measured via Overfilled Launch per TIA/EIA-455-204
**850nm measured via Effective Modal Bandwidth measured
via Differential Mode Delay as specified in EIA/TIA-455-220
ORDERING INFORMATION
Polarity Method A
Part Number
91-X2122-2YYY
91-X2122-6YYY
91-X2122-6EYYY
91-X2122-4YYY
91-X2222-2YYY
91-X2222-6YYY
91-X2222-6EYYY
91-X2222-4YYY
Polarity Method C
Part Number
91-X2133-2YYY
91-X2133-6YYY
91-X2133-6EYYY
91-X2133-4YYY
91-X2233-2YYY
91-X2233-6YYY
91-X2233-6EYYY
91-X2233-4YYY
Fibre Type
ModLink Cable Multimode OFPN 62.5/125µ OM1
ModLink Cable Multimode OFPN 50/125µ OM2
ModLink Cable Multimode OFPN 50/125µ OM3 (10G)
ModLink Cable Single Mode OFPN OS1
ModLink Cable Multimode LSZH 62.5/125µ OM1
ModLink Cable Multimode LSZH 50/125µ OM2
ModLink Cable Multimode LSZH 50/125µ OM3 (10G)
ModLink Cable Single Mode LSZH OS1
Length Requirements: Insert length requirement in place of YYY in proper part number.
Corporate Headquarters
Illinois, USA
Tel: 630-969-4550
MOLEX PREMISE NETWORKS
European Headquarters
Hampshire, England
Tel: 44 (0) 1489 527111
www.molexpn.com
©2008, Molex Printed in USA Form# 91-X2122_X2233
Asia Pacific Headquarters
Victoria, Australia
Tel: 61 3 9971 7111
Issue 4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising