CY3280-22X45 Datasheet
■
■
■
From the Device menu, select CY8C22545-24AXI
Click Program. "Programming Succeeded..." appears in the Actions pane when
programming is completed
Click Toggle Device Power. The D1 and D2 LEDs on the CY3280-22X45 board
lights red
5. Test the Board
Touch one or more buttons at a time. Each button touch lights up the corresponding
LED. You can touch multiple buttons simultaneously.
6. Design Support and Resources
A wealth of information about PSoC Designer™ and CapSense® Best Practices are
available on the www.cypress.com web site. For knowledge base articles, customer
forums, and online application support, visit www.cypress.com/go/support.
CY3280-22X45 Universal CapSense® Controller
Development Kit Quick Start
Doc. # 001-51973 Rev. *A
©2009-2011 Cypress Semiconductor Corporation. PSoC Designer and Programmable System-on-Chip are
trademarks, and PSoC and CapSense are registered trademarks of Cypress Semiconductor Corp. All other
trademarks or registered trademarks referenced herein are property of the respective corporations.
Cypress Semiconductor Corporation
198 Champion Ct., San Jose, CA 95134 USA
www.cypress.com
If you have questions, call
Cypress Customer Support
+1 (800) 541-4736 Ext. 8 (in the USA),
+1 (408) 943-2600 Ext. 8 (International),
or visit www.cypress.com/go/support
Doc. # 001-51973 Rev. *A
Cypress Semiconductor
198 Champion Court
San Jose, CA 95134-1709
Phone (USA): 800.858.1810
Phone (Intnl): 408.943.2600
http://www.cypress.com
1. Kit Contents
3. Getting Started
Each CY3280-22X45 kit contains:
■ CY3280-22X45 Universal CapSense Controller Board
■ CY3280-22X45 Universal CapSense Controller Board CD
■ CY3240-I2CUSB Board
■ CY3210-MiniProg1 Programmer
■ Printed Documents
The example firmware is available on the CD. Insert the CY3280-22X45 Kit CD into
the CD drive of your PC. Follow the instructions to complete software installation. For
more information, refer to the CY3280-22x45 Universal Capsense Controller
Development Kit Guide available on the CD.
Prerequisites:
■ CY3280-SLM Universal CapSense Linear Slider Module Board
■ CY3215-ICE
■ CY3250-22X45 Pod
Universal CapSense Module boards are available for purchase separately, or as part
of the combination kits. Do visit www.cypress.com for more information.
2. Module Hardware
Note The example in this Quick Start is for the CY3280-22X45 Universal CapSense
Controller Board and CY3280-SLM Universal CapSense Linear Slider Module Board.
4. Code Example
This example demonstrates the use of CY3280-22X45 Universal CapSense Controller
with CY3280-SLM. These instructions assume that your board is programmed with
the factory settings.
■ Connect the CY3280-SLM board to the CY3280-22X45 Universal CapSense
Controller board's P2 receptacle connector
This kit contains the components and sensors detailed in this figure.
■
■
■
■
■
■
■
Page 2
Place shunts on pins 2 and 3 of JP1 and pins 1 and 2 of JP4 (default setting)
Place shunts on pins 2 and 3 of JP2 on CY3280-SLM board
The code examples are available on the CD and on www.cypress.com; search for
CY3280-22X45
To reset the board to the factory conditions, connect your computer to the
CY3280-22X45 board ISSP connector (J3) using the PSoC MiniProg and a USB
cable
Open PSoC Programmer by going to the Windows Start menu All Programs >
Cypress > PSoC Programming > PSoC Programmer
Click File Load and open the CY3280_22X45_SLM.hex file on the CD at:
Firmware\CY3280_22X45_SLM\CY3280_22X45_SLM.hex
From the Device Family menu, select 22X45
Page 3
1. Kit Contents
3. Getting Started
Each CY3280-22X45 kit contains:
■ CY3280-22X45 Universal CapSense Controller Board
■ CY3280-22X45 Universal CapSense Controller Board CD
■ CY3240-I2CUSB Board
■ CY3210-MiniProg1 Programmer
■ Printed Documents
The example firmware is available on the CD. Insert the CY3280-22X45 Kit CD into
the CD drive of your PC. Follow the instructions to complete software installation. For
more information, refer to the CY3280-22x45 Universal Capsense Controller
Development Kit Guide available on the CD.
Prerequisites:
■ CY3280-SLM Universal CapSense Linear Slider Module Board
■ CY3215-ICE
■ CY3250-22X45 Pod
Universal CapSense Module boards are available for purchase separately, or as part
of the combination kits. Do visit www.cypress.com for more information.
2. Module Hardware
Note The example in this Quick Start is for the CY3280-22X45 Universal CapSense
Controller Board and CY3280-SLM Universal CapSense Linear Slider Module Board.
4. Code Example
This example demonstrates the use of CY3280-22X45 Universal CapSense Controller
with CY3280-SLM. These instructions assume that your board is programmed with
the factory settings.
■ Connect the CY3280-SLM board to the CY3280-22X45 Universal CapSense
Controller board's P2 receptacle connector
This kit contains the components and sensors detailed in this figure.
■
■
■
■
■
■
■
Page 2
Place shunts on pins 2 and 3 of JP1 and pins 1 and 2 of JP4 (default setting)
Place shunts on pins 2 and 3 of JP2 on CY3280-SLM board
The code examples are available on the CD and on www.cypress.com; search for
CY3280-22X45
To reset the board to the factory conditions, connect your computer to the
CY3280-22X45 board ISSP connector (J3) using the PSoC MiniProg and a USB
cable
Open PSoC Programmer by going to the Windows Start menu All Programs >
Cypress > PSoC Programming > PSoC Programmer
Click File Load and open the CY3280_22X45_SLM.hex file on the CD at:
Firmware\CY3280_22X45_SLM\CY3280_22X45_SLM.hex
From the Device Family menu, select 22X45
Page 3
■
■
■
From the Device menu, select CY8C22545-24AXI
Click Program. "Programming Succeeded..." appears in the Actions pane when
programming is completed
Click Toggle Device Power. The D1 and D2 LEDs on the CY3280-22X45 board
lights red
5. Test the Board
Touch one or more buttons at a time. Each button touch lights up the corresponding
LED. You can touch multiple buttons simultaneously.
6. Design Support and Resources
A wealth of information about PSoC Designer™ and CapSense® Best Practices are
available on the www.cypress.com web site. For knowledge base articles, customer
forums, and online application support, visit www.cypress.com/go/support.
CY3280-22X45 Universal CapSense® Controller
Development Kit Quick Start
Doc. # 001-51973 Rev. *A
©2009-2011 Cypress Semiconductor Corporation. PSoC Designer and Programmable System-on-Chip are
trademarks, and PSoC and CapSense are registered trademarks of Cypress Semiconductor Corp. All other
trademarks or registered trademarks referenced herein are property of the respective corporations.
Cypress Semiconductor Corporation
198 Champion Ct., San Jose, CA 95134 USA
www.cypress.com
If you have questions, call
Cypress Customer Support
+1 (800) 541-4736 Ext. 8 (in the USA),
+1 (408) 943-2600 Ext. 8 (International),
or visit www.cypress.com/go/support
Doc. # 001-51973 Rev. *A
Cypress Semiconductor
198 Champion Court
San Jose, CA 95134-1709
Phone (USA): 800.858.1810
Phone (Intnl): 408.943.2600
http://www.cypress.com
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Cypress Semiconductor:
CY3280-22X45
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising