Episode Accessories Installation Manual

Episode Accessories Installation Manual
INSTALLATION MANUAL
EPISODE ACCESSORIES
page | 2
PRE-INSTALL
Pre-Construction Brackets
Pre-Construction brackets are color coded and available in four sizes:
Color
Model
Yellow
IC-4
Green
IC-6*
IW-6
Red
IC-8
IW-8
Blue
IWLCR-6
* For POINT-6 models, refer to IC-8 cutout dimensions.
1. Connect the wing to the bracket.
NOTE: Press and hold the release button, then slide the wing away from
the bracket to disconnect.
Edge Plate
Release
Button
The in-ceiling speakers include an egde plate to secure if mounting
the speaker against a joist.
page | 3
The in-wall speakers require four points of connection to provide
proper support. Two bracket wings are included and must be cut
into four segments using tin snips. Connect the four wing segments
to the bracket and secure to studs.
Bracket
Wing
Segments
Bracket
Wing
Segments
2. Use the 1" markers as a placement guide for aligning the brackets.
Drive a screw through the metal wings to secure into the desired
position.
Bracket
1" Markers
Wing
3. Secure wiring within reach of the bracket for easy access.
© 2015 Episode®
page | 4
INSTALL
Rear Enclosures (For Signature Speakers Only)
1. Remove the speaker
interconnect cover.
Speaker
Interconnect
Cover
2. Attach the speaker to the
appropriate
enclosure
before mounting.
3. Use the embossed guide
to align the enclosure with
the product label.
4. Secure
enclosure
to
speaker using the screws
provided.
Note: In-wall models include
additional screws around the
magnet of the speaker.
5. Connect wires to the
terminals on top of the
enclosure.
Align with
Product
Label
page | 5
Refer to the following charts to verify the correct dimensions prior to
cutting drywall.
Model
Cutout Dimension
Mounting Depth
with Enclosure
IC-4
6.2”
5.9”
IC-6*
8.3"
6.2"
IC-8
9.7"
6.6"
* For POINT-6 models, refer to IC-8 cutout dimensions.
Model
Cutout Dimension
Mounting Depth
with Enclosure
IW-6
11.7" x 7.6"
3.8"
IW-8
13.7" x 9.0"
3.8"
LCR
14.4" x 7.6"
3.8"
© 2015 Episode®
page | 6
POST-INSTALL
Grille Options
See the chart below for available grille options.
Speaker
Grille
Round
In-Ceiling
Thin Bezel
In-Wall
Bezel-less



Bezel-less

Rectangular
Square
Thin Bezel


Install
For round in-ceiling and rectangular in-wall grilles, simply attach onto the
speaker.
Follow the steps below to attach square grilles.
1. Use four #8 Phillips screws
(not included) to mount the
adapter plate to the desired
area in the ceiling.
2. Fit the speaker over the adapter
plate.
3. Attach the grille to the
adapter plate.
WARRANTY
Lifetime Limited Warranty
Episode® Accessories have a Lifetime Limited Warranty. This warranty
includes parts and labor repairs on all components found to be
defective in material or workmanship under normal conditions of
use. This warranty shall not apply to products that have been abused,
modified or disassembled. Products to be repaired under this warranty
must be returned to a designated service center with an assigned
return authorization (RA) number. Contact technical support at
support@episodeaudio.com for an RA number.
CONTACTING TECHNICAL SUPPORT
866.838.5052
support@episodeaudio.com
© 2015 Episode®
Rev: 151028-1505
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising