Vig450_Vig451J BIOS manual
Components
Description
BIOS manual
D3288/D3348/D3358
Congratulations on your purchase of an innovative
product from Fujitsu.
The latest information about our products, tips, updates etc. can be found
on the Internet at: "http://www.fujitsu.com/fts/"
You can find driver updates at: "http://support.ts.fujitsu.com/download"
Should you have any technical questions, please contact:
•
our Hotline/Service Desk (see the Service Desk list or visit:
"http://support.ts.fujitsu.com/contact/servicedesk")
• Your sales partner
• Your sales office
We hope you enjoy working with your new Fujitsu system!
Published by / Contact address in EU
Fujitsu Technology Solutions
Mies-van-der-Rohe-Straße 8
80807 Munich, Germany
http://www.fujitsu.com/fts/
Copyright
© Fujitsu Technology Solutions 2015. All rights reserved.
Publication Date
04/2015
Order No.: A26361-D3288-Z350-1-7619, edition 1
BIOS manual
D3288/D3348/D3358
Manual
Introduction
9
Navigating BIOS Setup
11
Main Menu – System functions
13
Advanced Menu – Advanced
system configuration
15
Security Menu – Security Functions
44
Power Menu – Energy saving functions
53
Event Logs – Configuration and
Display of the Event Log
57
IPMI Management
60
Boot Menu – System boot
67
Save & Exit Menu – Finish BIOS Setup
70
BIOS Update
73
Index
76
Remarks
Product description information meets the design requirements of Fujitsu and is provided
for comparison purposes. The actual results may differ due to several factors. Subject
to technical changes without prior notification. Fujitsu rejects any responsibility with
regard to technical or editorial errors or omissions.
Trademarks
Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu Limited or its
subsidiaries in the United States and other countries.
Microsoft and Windows are trademarks or registered trademarks of the Microsoft
Corporation in the United States and/or other countries.
Intel and Pentium are registered trademarks and MMX and OverDrive are
trademarks of Intel Corporation, USA.
PS/2 and OS/2 Warp are registered trademarks of International Business Machines, Inc.
Any other trademarks specified herein are the property of their respective owners.
Copyright
No part of this publication may be copied, reproduced or translated without
the prior written consent of Fujitsu.
No part of this publication may be saved or transmitted by any electronic means
without the written consent of Fujitsu.
Contents
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notational conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
10
Navigating BIOS Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Open BIOS Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
If you want to open the Boot Menu immediately . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
If you wish to boot immediately from LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Navigating BIOS Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exiting BIOS Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
11
11
12
12
12
Main Menu – System functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Open source software license information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Date / System Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Access Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
13
13
13
14
14
Advanced Menu – Advanced system configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Erase Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Onboard Device Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LAN 1 Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LAN 2 Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Azalia HD Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto BIOS Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terms of Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic BIOS update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Update Server address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Silent update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manually check for update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCI Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCI Slot n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCI Subsystem Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCI Common Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCI Express Link Register Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CPU Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hyper-threading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Active Processor Cores . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Limit CPUID Maximum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware Prefetcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjacent Cache Line Prefetcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DCU (Data Cache Unit) Streamer Prefetcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DCU Ip (Instruction pointer-based) Prefetcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intel Virtualization Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VT-d . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intel TXT Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enhanced SpeedStep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Turbo Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Override OS Energy Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Energy Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CPU C1E Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
16
17
17
18
18
18
18
19
19
19
19
20
20
20
20
21
22
22
23
23
23
24
24
24
25
25
25
25
26
26
26
26
27
Fujitsu
3
Contents
CPU C3 Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CPU C6 Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package C State limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
QPI Link Frequency Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Uncore Frequency Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Runtime Error Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ECC Memory Error Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCI Error Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIMM xx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NUMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DDR Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SATA Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SATA Controller Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
sSATA Controller Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SATA Port n . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMART Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMART Self Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acoustic Management Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acoustic Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acoustic Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CSM Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Launch CSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot Option Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Launch PXE OpROM Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Launch Storage OpROM Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Launch Video OpROM Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Other PCI Device ROM Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TPM (Trusted Platform Module) Computing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TPM Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TPM State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pending TPM operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current TPM Status Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xHCI Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Legacy USB Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mass Storage Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB Port Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB Port Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB Device Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Firmware Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMCS Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fan Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Super IO Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Super IO Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Port 1 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Change Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
27
27
27
27
28
28
28
28
28
29
30
30
30
30
30
31
32
32
32
33
33
33
33
33
34
34
34
34
34
35
35
35
35
35
36
36
36
36
37
37
37
38
38
38
38
38
38
39
39
39
39
39
39
Fujitsu
Contents
Serial Port Console Redirection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Console Redirection Settings (for COM0 and COM4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bits per Second . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stop Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flow Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AMT Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ME Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unconfigure AMT/ME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MEBx Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IFR Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network Stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ipv4 PXE Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ipv6 PXE Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Option ROM Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Launch Slot n OpROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UEFI Device Driver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Driver Health . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40
40
40
40
40
41
41
41
41
41
41
42
42
42
42
42
43
43
43
43
Security Menu – Security Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Password Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Administrator Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Password on Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Skip Password on WOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FLASH Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDD Security Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDD Password on Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDD n / HDD-ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDD Password Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDD Password Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security Supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security Enabled . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security Locked . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security Frozen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDD User Password Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDD Master Password Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set User Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set Master Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Secure Boot Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Platform Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Secure Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Secure Boot Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Secure Boot Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Key Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Factory Default Key Provisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delete All Secure Boot Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enroll All Factory Default Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Save Secure Boot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Platform Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delete PK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44
45
45
45
46
46
46
46
46
47
47
47
47
47
47
47
47
47
48
48
48
48
48
49
49
49
49
49
50
50
50
50
Fujitsu
5
Contents
Set new PK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Key Exchange Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delete KEK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set new KEK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Append KEK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Authorized Signatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delete DB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set new DB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Append DB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Authorized TimeStamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delete DBT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set new DBT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Append DBT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Forbidden Signatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delete DBX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set new DBX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Append DBX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50
50
50
50
51
51
51
51
51
51
51
51
51
52
52
52
52
Power Menu – Energy saving functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power On Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low Power Soft Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Failure Recovery – System status after a power failure . . . . . . . . . . . . . . . . . . . . . . . . . .
Hibernate like Soft Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB At Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wake-Up Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wake On LAN Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wake Up Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Minute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Second . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wake Up Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wake Up Day . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USB Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
53
53
54
54
54
55
55
55
55
55
55
55
56
56
56
56
Event Logs – Configuration and Display of the Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Change SMBIOS event log settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SMBIOS Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Erase Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When Log is full . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Log System Boot Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MECI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
METW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Log OEM Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Convert OEM codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
View SMBIOS Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
57
57
57
58
58
58
58
58
58
58
59
IPMI Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Asset tag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Onboard Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot Retry Counter: Number of attempts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Cycle Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASR&R Boot Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
60
60
60
61
61
61
6
Fujitsu
Contents
Temperature Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Event Log Full Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Load iRMC Default Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Failure Recovery - system status after a power failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Multiplexer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot Watchdog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timeout Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Action – action when time monitoring expires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iRMC Lan Parameters Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iRMC MAC Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management LAN Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VLAN ID tagging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VLAN ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VLAN Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iRMC IPv4 LAN stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Subnet Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gateway address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
iRMC IPv6 LAN Stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Link Local Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IPv6 Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Console Redirection (CR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Console Redirection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Baud rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flow Control - interface settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
62
62
62
62
63
63
63
63
64
64
64
64
64
64
65
65
65
65
65
65
65
66
66
66
66
66
66
Boot Menu – System boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bootup NumLock State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quiet Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Check Controller Health Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PXE Boot Option Retry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot Error Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Primary Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot Removable Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Virus Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot option priorities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
67
67
67
68
68
68
68
68
69
69
69
Save & Exit Menu – Finish BIOS Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Save Changes and Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Discard Changes and Exit - quit without saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Save Changes and Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Discard Changes and Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Save Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Save Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Discard Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restore Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Save as User Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restore User Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70
70
70
70
71
71
71
71
71
71
71
71
72
Fujitsu
7
Contents
BIOS Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto BIOS Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flash BIOS update under Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flash BIOS update with a USB stick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BIOS Recovery Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
73
73
73
74
75
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
76
8
Fujitsu
Introduction
Introduction
BIOS Setup
BIOS Setup provides settings for system functions and the hardware configuration for the system.
Any changes you make to the settings take effect as soon as you save the settings and quit BIOS Setup.
The individual menus in BIOS Setup provide settings for the following areas:
Main:
Advanced:
Security:
Power:
IPMI Mgmt:
Boot:
Save & Exit:
System functions
Advanced system configuration
Security functions
Energy saving functions
IPMI management
Configuration of the start-up sequence
Save and quit
The setting options depend on the hardware configuration of your system.
Some menus and certain settings may therefore not be available in BIOS Setup on your
system, or the menus may be in a different place, depending on the BIOS revision.
Fujitsu
9
Introduction
Notational conventions
Pay particular attention to texts marked with this symbol. Failure to observe
this warning endangers your health, destroys the system, or may lead
to loss of data. The warranty will be invalidated if the system becomes
defective through failure to take notice of this warning.
Indicates important information which is required to use the system properly.
►
Indicates an activity that must be performed.
Indicates a result.
This font
Indicates data entered using the keyboard in a program dialogue or
command line, e.g. your password ((Name123) or a command used to
start a program (start.exe).
Indicates information that is displayed on the screen by a program, e.g.:
Installation is complete!.
Indicates
"This font"
• terms and texts used in a software interface, e.g.: Click on Save.
• names of programs or files, e.g. Windows or setup.exe.
Indicates
This font
This font
•
•
Abc
10
cross-references to another section, e.g. "Safety information"
cross-references to an external source, e.g. a web address: For more
information, go to "http://www.fujitsu.com/fts/"
• names of CDs, DVDs and titles or designations for other materials, e.g.:
"CD/DVD Drivers & Utilities" or "Safety" manual.
Indicates a key on the keyboard, e.g: F10 .
Fujitsu
Navigating BIOS Setup
Navigating BIOS Setup
Open BIOS Setup
► Switch on the system.
Wait until the screen output appears.
► Press function key F2 .
► If the system is password protected, you must now enter the password and confirm with the
Enter key. You will find details on password assignment under "Password Description", Page 45.
The BIOS Setup Main menu will be displayed on the screen.
► To display system-specific information, select System Information and press the Enter key.
The BIOS release information will be displayed:
• The revision of the BIOS (e.g. R1.3.0)
Under "Board" you will find the system board number (e.g. D3062-A11)
With the aid of the system board number you can locate the correct technical manual for
the system board on the "Drivers & Utilities" CD/DVD. Alternatively you can also use it to
download the corresponding BIOS update file from the Internet (see "BIOS Update", Page 73).
BIOS-Setup
Setup,
BIOSSetup
If you want to open the Boot Menu immediately
You can use this function if you do not wish to boot your system from the drive which
is given as the first setting under Boot Option Priorities in the Boot menu.
BootMenu
► Start the system and wait until screen output appears.
► Press the function key F12 .
On the screen, the boot options are shown as a popup window. You can now select the
drive from which you wish to boot the operating system. The selection options are the same
as the possible settings given under Boot Option Priorities in the Boot submenu.
F12,functionkey
Bootmenu
cursor keys to select which drive you want to boot the operating
and
► Use the
system from now and confirm your choice with the Enter key.
Your selection is only valid for the current system boot. At the next system
boot, the settings in the Boot menu are valid again.
► If you want to start the BIOS Setup, use the cursor keys
or
to select the
Enter Setup entry and confirm your selection with the Enter key.
► If you want perform basic tests of the CPU, working memory and hard disks, use the cursor keys
or
Fujitsu
to select the Diagnostic Program entry and confirm your selection with the Enter key.
11
Navigating BIOS Setup
If you wish to boot immediately from LAN
► Press the function key F11 if you wish to boot directly via LAN and not from the drive which
is given as the first position under Boot Option Priorities in the Boot menu.
LAN
Bootmenu
Navigating BIOS Setup
BIOS Setup
Select menu from menu bar
or
cursor keys
Select field - selected field is highlighted
or
cursor keys
Enter or ESC
+ or - keys (numeric keypad)
F3 function key
F2 function key
Open submenu (marked by ►) Enter and leave ESC
Change entry for field
Set default entries for all menus
Reset entries that were in use when BIOS Setup was opened.
Exiting BIOS Setup
► Select the Save & Exit menu from the menu bar to end BIOS Setup.
You can then decide whether you want to save the changed settings.
► Select the required option.
► Press the Enter key.
12
Fujitsu
Main Menu – System functions
Main Menu – System functions
BIOS Setup
MainMenu
Example showing the Main menu
The Main Menu is entered, to determine the basic system configuration and to provide an
overview. Some of the parameters are only available under certain conditions.
System Information
System Information
The System Information submenu gives you an overview of the system configuration. This
includes information about the CPU, memory and LAN configuration.
Open source software license information
Opensourcesoftwarelicenseinformation
This submenu provides the licence information for the open source software
that is used in this system board.
System Language
System Language
Specifies the language used in the BIOS Setup.
Fujitsu
13
Main Menu – System functions
System Date / System Time
System Date/System Time
Time
Date
Shows the currently set date / the currently set time of the system. The date has the format
"Day of the week, month/day/year". The time has the format "hours/minutes/seconds".
If you wish to change the currently set date / the currently set time, enter the new date
in the field System Date and the new time in the field System Time. Use the tab key to
switch the cursor between the System Time and System Date fields.
If the system date & time fields are often set incorrectly when starting the computer,
the lithium battery is possibly discharged and must be changed. The procedure for
changing the lithium battery is described in the system board manual.
Access Level
Access
AccessLevel
Shows the current access level in BIOS Setup. If the system is not protected by a password, or an
administrator password has been allocated, the access level is Administrator. If administrator
and user passwords are allocated, the access level depends on the password entered.
14
Fujitsu
Advanced Menu – Advanced system configuration
Advanced Menu – Advanced system
configuration
BIOS Setup
Advancedmenu
The advanced functions which are available to the system are configured in this
menu for the advanced system configuration.
Only change the default settings if required for a special purpose.
Incorrect settings can cause malfunctions.
Memory Configuration
SMART Settings
CSM Configuration
Network Stack Configuration
Option ROM Configuration
Intel(R) Ethernet Connection I217-LM - 90:1B:0E:01:CF:E8
Intel(R) I210 Gigabit Network Connection 90:1B:0E:32:F1:F0
Driver Health
Example showing the Advanced menu
Fujitsu
15
Advanced Menu – Advanced system configuration
Erase Disk
EraseSATAhard disk
EraseDisk
Erase Disk is a firmware incorporated in Fujitsu Technology Solutions (UEFI: Unified Extensible
Firmware Interface), to delete all the data from SATA hard disk(s).
This function allows all the data on internal or external SATA hard disks connected via
the eSATA connection to be irretrievably deleted, before disposal of the hard disks or
the complete computer system. The function can also be used if hard disks need to be
completely deleted, for example before installing a new operating system.
The application can only be selected and run if an administrator/supervisor
password has been assigned (BIOS Setup -> Security Menu).
To delete hard disks in a RAID system, the mode of the RAID controller must be changed,
e.g. to IDE Mode or AHCI Mode in the SATA Configuration submenu of the Advanced menu.
Proceed as follows to delete data from SATA hard disks:
► Call up the BIOS Setup with the administrator/supervisor password.
► To start the application, select Erase Disk (BIOS Setup -> Advanced or BIOS
Setup -> Security) and set Start after Reboot.
► Then select Save Changes and Exit in the menu Save & Exit / Exit to initiate a reboot and Erase Disk.
As a result of the reboot, the Erase Disk menu is started. You have the option
of interrupting the process during the user selection.
► After the application starts, the administrator/supervisor password must
be entered for security reasons.
A dialogue field appears in which a particular, several or all the hard disks can be selected
for deletion - this depends on the number of hard disks in your system.
► Select the hard disk(s) to be deleted.
The selected hard disk(s) will be deleted individually.
16
Fujitsu
Advanced Menu – Advanced system configuration
Erase Disk offers four deletion options, from "fast" (with one deletion pass) to
"very secure" (with 35 deletion passes). Depending on the algorithm chosen, the
process can take between ~10 seconds and ~10 minutes per GB:
•
•
•
•
Zero Pattern (1 pass)
German BSI/VSITR (7 passes)
DoD 5220.22-M ECE (7 passes)
Guttmann (35 passes)
You can find further information on the deletion algorithms here:
•
•
•
"https://www.bsi.bund.de/cln_174/DE/Publikationen/publikationen_node.html"
"http://www.usaid.gov/policy/ads/500/d522022m.pdf"
"http://www.cs.auckland.ac.nz/~pgut001/pubs/secure_del.html"
► Select the hard disk deletion algorithm which you wish to use.
The complete deletion process can be copied as an audit-compliant log onto an external
USB drive, which must be formatted as FAT32. Just connect an external USB drive.
► Select whether a status report should be written to the USB stick.
The user can select the following tasks which are run by the system
after the deletion process:
•
•
•
•
Reset administrator and user password
Load BIOS setup defaults
Shutdown the computer
Exit Erase Disk with no additional options upon completion
► Select the function which you require.
The deletion process starts.
Disabled
Erase Disk will NOT be started after the next reboot.
Start after Reboot Erase Disk will be started after the next reboot.
Onboard Device Configuration
Onboard DeviceConfiguration
Opens the submenu to configure devices on the system board. Some of them
are only available under certain conditions.
LAN 1 Controller
LAN
Specifies whether the LAN 1 controller is available.
Disabled
Enabled
Fujitsu
The LAN 1 controller is not available.
The LAN 1 controller is available.
17
Advanced Menu – Advanced system configuration
LAN 2 Controller
LAN
Specifies whether the LAN 2 controller is available.
Disabled
Enabled
The LAN 2 controller is not available.
The LAN 2 controller is available.
Azalia HD Audio
AudioConfiguration
Only for versions D3348 and D3358.
Allows the onboard Azalia HD (High Definition) audio controller to be enabled.
Disabled
Enabled
The onboard audio controller is disabled.
The onboard audio controller is enabled.
Auto BIOS Update
Automatic BIOSUpdate
With Auto BIOS Update it is possible to check a Fujitsu server automatically to
see if there is a new BIOS version for the system. For the update, no operating
system or external storage medium is required.
To be able to use this function, the computer must have access to the Internet over
a network. Access to the Internet must take place via a gateway and a DHCP server
must be present in the network for the allocation of IP addresses.
Please also note the terms of use, which are included as an Annex to the BIOS
manual or can be found on the Internet at "tou.ts.fujitsu.com".
Terms of Use
TermsofUse
Update
In order to be able to use the Auto BIOS Update function, you must accept the terms of use, which
are included as an Annex to the BIOS manual or can be found on the Internet at "tou.ts.fujitsu.com".
Decline
Accept
The Terms of Use were not accepted. The Auto BIOS Update function cannot
be used.
The Terms of Use were accepted. The Auto BIOS Update function can be used.
FLASH Write Support must be enabled before the Auto BIOS Update function can be used.
18
Fujitsu
Advanced Menu – Advanced system configuration
Automatic BIOS update
Automatic BIOSUpdate
Defines how frequently BIOS updates are searched for on the Fujitsu server. If the
automatic BIOS update function is disabled, it is possible under Manually check for
update to search for BIOS updates at the next system boot.
Disabled
Daily
Weekly
Monthly
Quarterly
BIOS
BIOS
BIOS
BIOS
BIOS
updates
updates
updates
updates
updates
are not automatically searched for.
are searched for daily.
are searched for once per week.
are searched for once per month.
are searched for once every three months.
Update Server address
Server address
Update
Shows the address of the TFTP server on which BIOS updates are searched for.
The preset Fujitsu Update Server can be reached at the address "webdownloads.ts.fujitsu.com".
With the fee-based advanced version of Auto BIOS Update, there is the option to use one’s own TFTP
server. Either a domain name or a direct IPv4 address of the desired update server can be entered.
The name resolution of a domain name occurs at first via the DNS server configured
through DHCP. If no DNS server is configured or the DNS server cannot be reached,
name resolution is attempted through the Google DNS server via IP address 8.8.8.8.
The Neustar DNS service at IP address 156.154.70.1 is used as a second fallback.
Silent update
Update
Defines if the BIOS update, if a new BIOS version is available, is executed automatically
without an input request and only a notification is displayed.
Disabled
Enabled
It is possible to execute the BIOS update immediately, to skip it with this
system boot or to ignore the new BIOS version.
The BIOS update is executed automatically without an input request.
Manually check for update
Update
Defines if a BIOS update is searched for during the next system reboot.
This function is automatically reset to disabled after a search has been performed.
Disabled
Enabled
Fujitsu
No BIOS update is searched for at the next system reboot.
A BIOS update is searched for at the next system reboot.
19
Advanced Menu – Advanced system configuration
PCI Status
expansion card
PCI
slots
This submenu shows the current state of the expansion cards in the slots.
PCI Slot n
Shows the current state of the expansion card in this slot.
Failed
Enabled
Empty
A fault was identified for this slot. The expansion card in this slot possibly
has a problem.
No faults were reported for this slot. The expansion card in this slot can be
used without limitation.
There is no expansion card in this slot.
PCI Subsystem Settings
PCI Common Settings
PERR# Generation
PCI
Specifies whether PERR# (PCI parity errors) are created.
Disabled
Enabled
PCI parity errors will not be created.
PCI parity errors will be created.
SERR# Generation
PCI
Specifies whether SERR# (PCI system errors) will be created.
Disabled
Enabled
20
PCI system errors will not be created.
PCI system errors will be created.
Fujitsu
Advanced Menu – Advanced system configuration
PCI Express Link Register Settings
ASPM Support
PCI
Configure Active State Power Management (ASPM) to gradually reduce the power consumption
of the PCI Express Link and thus save energy. Even if ASPM is generally enabled by this
selection, it is only then invoked for a particular connection if the corresponding PCI Express
adapter card or the corresponding Onboard Controller also supports this.
Disabled
L1 Only
ASPM is disabled. The power consumption for PCI Express connections is not
reduced. Best compatibility.
Limit the Low Power Mode of the PCI Express connections to L1 (bi-directional).
The latency (delay) for PCI Express devices can increase if ASPM is not
disabled. Various adapter cards do not support this function correctly, which
can lead to an unpredictable behaviour of the system.
Above 4G Decoding
Decoding
Defines whether memory resources can be assigned to PCI devices above the 4GB address
limit. The selection depends on the operating system and the adapter cards.
Disabled
Enabled
Only memory resources below the 4GB address limit are assigned to the
PCI devices.
This selection must be made for 32-bit operating systems, but is also supported
by 64-bit operating systems.
Memory resources above the 4GB address limit can be assigned to PCI
devices if they have 64-bit address decoding.
This option is only supported by 64-bit operating systems.
This selection can be necessary if the integrated PCI Express devices (e.g.
co-processor adapter cards) have a large memory requirement that cannot fit
into the address space below 4 GB.
PCI address decoding is limited to the 4GB address limit for 32-bit operating systems,
even if the available PCI devices support 64-bit address decoding.
Fujitsu
21
Advanced Menu – Advanced system configuration
Memory Hole Size
The total memory size below the 4GB address limit can be selected here. This total
memory also includes allocated memory resources which are requested by PCI devices.
The DRAM address space which is replaced by the total memory is allocated again to
the area above the 4 GB address limit and can still be used.
2GB
3GB
The total memory has a size of 2 GB. The remaining 2 GB address space
below the 4 GB address limit is available for DRAM.
The total memory has a size of 3 GB. The remaining 1 GB address space
below the 4 GB address limit is available for DRAM. Normally, this selection is
only used for 32 bit operating systems and PCI adapter cards which demand a
very large PCI address space.
DMI control
Selects the speed of the connection between the CPU and the chipset. Low speed leads
to low power consumption but also less system performance.
GEN1
GEN2
The bus connection between the CPU and the chipset is set to a speed
of 2.5 GT/s.
The bus connection between the CPU and the chipset is set to a speed
of 5.5 GT/s.
CPU Configuration
Opens the CPU Configuration submenu. Some of the parameters are only
available under certain conditions.
Hyper-threading
HyperThreading
Hyper-threading technology allows a single physical processor to appear as several logical
processors. With this technology, the operating system can better utilise the internal
processor resources, which leads to an increase in performance. The advantages of this
technology can only be used by an operating system that supports ACPI. This setting
has no effect on operating systems without ACPI support.
Disabled
Enabled
22
An ACPI operating system can only use the first logical processor of the physical
processor. This setting should therefore only be chosen if the operating system
does not support hyper-threading technology.
An ACPI operating system can use all the logical processors of the physical
processor.
Fujitsu
Advanced Menu – Advanced system configuration
Active Processor Cores
ActiveProcessorCores
On processors which contain multiple processor cores, the number of active processor cores can be
limited. Inactive processor cores will not be used and are hidden from the operating system.
0
1..n
All available processor cores are active and can be used.
Only the selected number of processor cores is active. The other processor
cores are disabled.
The choice made here allows possible problems with certain software
packages or system licences to be solved.
Limit CPUID Maximum
LimitCPUIDMaximum
Specifies the number of CPUID functions which can be called from the processor. Some
operating systems cannot process new CPUID commands which support more than three
functions. This parameter should be enabled for these operating systems.
Disabled
Enabled
All CPUID functions are supported.
For reasons of compatibility with the operating system, only a reduced number
of CPUID functions is supported by the processor.
Hardware Prefetcher
HardwarePrefetcher
If this function is enabled, an automatic prefetch of the memory content anticipated to be needed
occurs when the memory bus is inactive. If the content is loaded from the cache and not from the
memory, the latency is reduced. This particularly applies to applications with linear data access.
With this parameter you can make performance settings for non-standard applications.
For standard applications, we recommend that the default settings are maintained.
Disabled
Enabled
Fujitsu
Deactivates the hardware prefetcher of the CPU.
Activates the hardware prefetcher of the CPU.
23
Advanced Menu – Advanced system configuration
Adjacent Cache Line Prefetcher
AdjacentCache LinePrefetcher
Available if the processor offers a mechanism by which an adjacent 64-byte cache line
can also be loaded during each cache request. The number of hits in the cache increases
as a result in the case of applications with high spatial locality.
With this parameter you can make performance settings for non-standard applications.
For standard applications, we recommend that the default settings are maintained.
Disabled
Enabled
The processor loads the requested cache line.
The processor loads the requested cache line and the adjacent cache line.
DCU (Data Cache Unit) Streamer Prefetcher
DataCacheUnit
With this option, data content which will probably be needed is automatically pre-loaded into the
L1 data cache when the memory bus is inactive. Because content is called from cache instead
of from memory, the latency is reduced, especially for applications with linear data access.
You can use this parameter to change the performance settings for non-standard
applications. We recommend that the default settings are kept for standard applications.
Enabled
Disabled
Enables the DCU Streamer Prefetcher function of the CPU.
Disables the DCU Streamer Prefetcher function of the CPU.
DCU Ip (Instruction pointer-based) Prefetcher
DataCacheUnit
Performance increases can be expected if code is used sequentially and in contiguous storage.
You can use this parameter to change the performance settings for non-standard
applications. We recommend that the default settings are kept for standard applications.
Enabled
Disabled
24
Enables the DCU Streamer Prefetcher function of the CPU.
Disables the DCU Streamer Prefetcher function of the CPU.
Fujitsu
Advanced Menu – Advanced system configuration
Intel Virtualization Technology
IntelVirtualizationTechnology
Used to support the visualisation of platform hardware and multiple software environments.
Based on Virtual Machine Extensions (VMX), to support the application of multiple software
environments under the use of virtual computers. The virtualisation technology enhances the
processor support for virtualisation purposes on the over 16 bit and 32 bit protected modes
and on the Intel® Extended Memory 64 Technology (EM64T) mode.
In active mode, a Virtual Machine Monitor (VMM) can use the additional
performance features of the Vanderpool Technology Hardware.
Disabled
A Virtual Machine Monitor (VMM) cannot use the additional performance features
of the hardware.
A VMM can use the additional performance features of the hardware.
Enabled
VT-d
VT-d
VT-d (Intel Virtualization Technology for Directed I/O) is a hardware support for the common use
of I/O devices by several virtual machines. VMM systems (Virtual Machine Monitor) can use
VT-d to manage various virtual machines which access the same physical I/O device.
Disabled
Enabled
VT-d is disabled and is not available for the VMMs.
VT-d is available for the VMMs.
Intel TXT Support
Enables Trusted Execution Technology (TXT) support. Intel® TXT is available if the CPU
in use supports Secure Mode Extensions (SMX), and both Virtualization Technology
(VT) and VT-d are enabled in the CPU submenu.
Intel TXT Support must be disabled before BIOS Update of the system is started.
Disabled
Enabled
TXT is disabled.
TXT is enabled.
Power Technology
Power Technology
Configures the CPU power management functions.
Disabled
Energy Efficient
Custom
Fujitsu
The CPU power management functions are disabled.
The CPU power management functions are optimised for energy efficiency.
Further setting options are available for the CPU power management
configuration.
25
Advanced Menu – Advanced system configuration
Enhanced SpeedStep
Enhanced SpeedStep
Specifies the voltage and frequency of the processor. EIST (Enhanced Intel
SpeedStep® Technology) is an energy-saving function.
The processor voltage is adapted to the particular system requirements
which are needed at any one time. A reduction in the clock frequency
causes the system to require less energy.
Disabled
Enabled
Enhanced SpeedStep functionality is disabled.
Enhanced SpeedStep functionality is enabled.
Turbo Mode
Turbo Mode
The processor may work faster than the specified frequency when the operating system requires the
maximum performance state (P0). This function is also known as Intel® Turbo Boost Technology.
Disabled
Enabled
Turbo Mode is disabled.
Turbo Mode is enabled.
Override OS Energy Performance
Override OSEnergyPerformance
Prevents the OS overwriting the energy efficiency settings from Setup.
Disabled
Enabled
Override OS Energy Performance is disabled.
Override OS Energy Performance is enabled.
Energy Performance
EnergyPerformance
Energy efficiency specifications for the processor on non-legacy operating systems. The
processor receives the instruction to adapt energy consumption and performance.
Performance
Balanced
Performance
Balanced Energy
Energy Efficient
Optimisation with respect to performance, where required at the cost of energy
efficiency.
Optimisation with respect to performance, with good energy efficiency.
Optimisation with respect to energy efficiency, with good performance.
Optimisation with respect to energy efficiency, where required at the cost of
performance.
Depending on the selected energy options, where required the operating system
selects a mode other than that selected in the Setup.
26
Fujitsu
Advanced Menu – Advanced system configuration
CPU C1E Support
CPUC1ESupport
If this is supported by the operating system, the processor will be stopped if possible, to save power.
Disabled
Enabled
The C1E power state function is not available.
The C1E power state function is available.
CPU C3 Report
CPUC3Report
Passes the processor C3 state to the Operating System Power Management (OSPM) as
ACPI-C2 state, if this is supported by the particular operating system being used.
Disabled
Enabled
OSPM does not show CPU C3 as ACPI-C2 state.
OSPM shows CPU C3 as ACPI-C2 state.
CPU C6 Report
CPUC6Report
Passes the processor C6 state as ACPI-C3 state to the OSPM, to enable
Processor Deep Power Down Technology.
Disabled
Enabled
CPU C6 is not passed as ACPI-C3 status to the OSPM.
CPU C6 is passed as ACPI-C3 status to the OSPM.
Package C State limit
Package CState limit
Allows the C state limit of the processor to be configured.
C0
C2
C6
C6 Retention
The
The
The
The
C
C
C
C
state
state
state
state
limit
limit
limit
limit
is
is
is
is
C0.
C2.
C6.
C6 Retention.
QPI Link Frequency Select
Creates the connection between the processors. QPI links can operate at different speeds,
depending on the processors. These parameters control the speed of the QPI links in your system.
Auto
The BIOS determines the maximum speed depending on the processors
in your system.
► If you wish to set the speed of the QPI links manually, select another value,
provided this is supported by your system.
Fujitsu
27
Advanced Menu – Advanced system configuration
Uncore Frequency Override
Specifies whether the uncore frequency of the CPU can be changed to increase the I/O performance.
Disabled
The processor controls the frequency autonomously in a predefined range
to save power.
The frequency is always set to its predefined maximum. This can result in
higher power consumption.
Enabled
Runtime Error Logging
ECC Memory Error Logging
Error Logging
MemoryError
Specifies whether ECC memory errors will be recognised and entered in the event log.
Enabled
Multi-bit Errors Only
Disabled
Both single-bit memory errors and multi-bit memory errors will be entered
in the event log.
Only multi-bit memory errors will be entered in the event log.
No memory errors will be entered in the event log.
PCI Error Logging
Specifies whether PCI errors will be entered in the event log.
To be able to recognise PCI errors, the creation of PERR# (PCI parity errors) or SERR#
(PCI system errors) must be enabled in advance in the menu PCI Subsystem Settings.
Disabled
Enabled
No PCI errors will be entered in the event log.
PCI errors will be entered in the event log.
Memory Status
Memory modules can be marked as faulty in this submenu. Faulty memory modules
are no longer used when the system is rebooted, provided at least one error-free bank
is available. The memory capacity is reduced accordingly.
28
Fujitsu
Advanced Menu – Advanced system configuration
DIMM xx
Shows the current status of the memory modules.
Enabled
Disabled
Failed
Empty
Fujitsu
The system uses the memory module.
The memory module will not be used by the system. It was manually disabled.
The memory module will not be used by the system. It was automatically
disabled by the system after a memory error. If you have replaced a defective
memory module, you must reset the entry to Enabled.
There is no memory module present.
29
Advanced Menu – Advanced system configuration
Memory Configuration
MemoryConfiguration
Opens the Memory configuration submenu.
NUMA
NUMA
NUMA (Non-Uniform Memory Access) is a memory architecture for multiprocessor systems. Each
processor has its own local memory, but can also access the local memory of other processors
(shared memory). Access to the local memory is faster than the access to the shared memories.
Disabled
Enabled
The whole system memory is divided into many small, interleaved areas of local
and shared memory. Use this option if the operating system does not support
NUMA.
The whole system memory is divided into fewer, larger, non-interleaved areas of
local and shared memory. On an ACPI operating system which supports NUMA,
this will achieve the best results with respect to performance.
DDR Performance
frequency
speed
DDRPerformance
The memory modules can operate at various speeds (frequencies).
The performance increases with higher speeds, on the other hand the energy-saving
increases with lower speeds. The possible memory speeds are determined by
the particular memory module configuration.
Energy
optimized
Performance
optimized
Lowest possible speed, to save energy.
Highest possible speed, for the best performance.
SATA Configuration
SATAConfiguration
Opens the SATA configuration submenu.
SATA Controller Configuration
SATA Controller
SATAController
Specifies whether the SATA controller is available.
Disabled
Enabled
30
The SATA controller is not available.
The SATA controller is available.
Fujitsu
Advanced Menu – Advanced system configuration
SATA Mode
SATAports
Specifies in which mode the SATA ports will be operated.
IDE
The SATA port is operated in IDE Mode.
The SATA port is operated in AHCI Mode.
The SATA port is operated in RAID Mode.
AHCI
RAID (if available)
To be able to start the RAID Setup during POST, the option Quiet
Boot must be set to Disabled.
Aggressive Link Power Management
AggressiveLink Power Management
In AHCI mode, makes it possible to allow Aggressive Link Power Management (ALPM) to save energy.
Disabled
Enabled
ALPM is disabled.
ALPM is enabled.
sSATA Controller Configuration
sSATA Controller
sSATA
Specifies whether the sSATA controller is available.
Disabled
Enabled
The sSATA controller is not available.
The sSATA controller is available.
sSATA Mode
Specifies in which mode the sSATA ports should be operated.
IDE
AHCI
RAID (if available)
The sSATA port is operated in IDE Mode.
The sSATA port is operated in AHCI Mode.
The sSATA port is operated in RAID Mode.
To be able to start the RAID Setup during POST, the option Quiet
Boot must be set to Disabled.
Aggressive Link Power Management
In AHCI mode, makes it possible to allow Aggressive Link Power Management (ALPM) to save energy.
Disabled
Enabled
Fujitsu
ALPM is disabled.
ALPM is enabled.
31
Advanced Menu – Advanced system configuration
SATA Port n
Indicates whether the SATA port is available, (Not Installed) or which drive
is connected to the SATA port.
Port n
SATAPortn
Specifies whether the SATA port is available.
Disabled
Enabled
The SATA port n is not available
The SATA port is available.
Staggered Spin-up
Staggered Spin-up
Reduces the electrical load during boot up of systems with multiple SATA devices. The SATA
devices run one after the other at the request of the HOST controller.
Disabled
Enabled
Staggered Spin-up is disabled.
Staggered Spin-up is enabled.
External SATA Port
ExternalSATAPort
Specifies whether the port will be operated internally as SATA or externally as eSATA.
Disabled
Enabled
The port will be used internally as SATA.
The port will be used as external SATA (eSATA).
Hot Plug
HotPlug
Specifies whether hot plug support of the port is enabled.
Disabled
Enabled
The hot plug support of the port is disabled.
The hot plug support of the port is enabled.
SMART Settings
Opens the submenu for enabling the hard disk self test.
SMART Self Test
Specifies whether the SMART (Self Monitoring, Analysis and Reporting Technology,
S.M.A.R.T.) self test is enabled for all hard disks during the POST.
Enabled
Disabled
32
The SMART self test is enabled during the POST.
The SMART self test is disabled during the POST.
Fujitsu
Advanced Menu – Advanced system configuration
Acoustic Management Configuration
Acoustic Management
Noiselevel
Open the submenu to set the noise level of hard disks or optical drives.
Acoustic Management
Specifies whether the functionality for setting the noise level of hard disks or optical
drives (Automatic Acoustic Management) is available.
Disabled
Enabled
Automatic Acoustic Management is not available.
Automatic Acoustic Management is available.
Acoustic Mode
Acoustic Mode
Specifies the noise level of the hard disk or the optical drive. The noise level of the drive is reduced
by decreasing its rotational speed. This function must be supported by the drive.
If the functionality for setting the noise level (Automatic Acoustic Management) is
disabled, the Acoustic Mode is Not Available. If the functionality for setting the noise
level (Automatic Acoustic Management) is enabled, but is not supported by the connected
SATA device, then Acoustic Mode is automatically set to Not supported.
Bypass
Quiet
Medium
Performance
High Performance
Max Performance
The drive is operated with its preset speed of rotation.
The drive is operated with the slowest possible speed of rotation. The drive is
operated with lower noise and limited performance.
The drive is operated with a medium speed of rotation. The drive is operated
with reduced noise and slightly reduced performance.
The drive is operated at slightly less than the highest possible speed of rotation.
The drive is operated at the highest possible speed of rotation.
CSM Configuration
CSM
Opens the submenu for configuring the Compatibility Support Module (CSM).
This submenu is only available if Secure Boot Control is disabled under
Setup –> Security –> Secure Boot Configuration.
Launch CSM
LaunchCSM
CSM
Specifies whether the Compatibility Support Module (CSM) is executed. A legacy operating
system can only be booted if the CSM has been loaded.
Enabled
Disabled
Fujitsu
The CSM is executed so that a legacy or UEFI operating system can be booted.
The CSM is not executed so that a only a UEFI operating system can be
booted.
33
Advanced Menu – Advanced system configuration
Boot Option Filter
BootOptionFilter
CSM
Specifies the drives from which booting can be carried out.
UEFI and Legacy
Legacy only
UEFI only
Booting is possible both from drives with UEFI OS and from drives with Legacy
OS.
Booting is only possible from drives with Legacy OS.
Booting is only possible from drives with UEFI OS.
Launch PXE OpROM Policy
LaunchPXEOpROM Policy
CSM
Specifies which PXE option ROM is booted. For the PXE boot, both the normal
(Legacy) PXE boot and a UEFI PXE boot are available.
Do not launch
UEFI only
Legacy only
No option ROMs are booted.
Only UEFI option ROMs are booted.
Only Legacy option ROMs are booted.
Launch Storage OpROM Policy
LaunchStorage OpROM Policy
CSM
Specifies which Storage option ROM is booted.
Do not launch
UEFI only
Legacy only
No Storage option ROMs are booted.
Only UEFI Storage option ROMs are booted.
Only Legacy Storage option ROMs are booted.
Launch Video OpROM Policy
LaunchVideo OpROM Policy
CSM
Specifies which Video option ROM is booted.
UEFI only
Legacy only
Only UEFI Video option ROMs are booted.
Only Legacy Video option ROMs are booted.
Other PCI Device ROM Priority
OtherPCIDeviceROM Priority
CSM
Specifies which option ROM is booted for devices other than the network, mass memory or video.
UEFI OpROM
Legacy OpROM
34
Only UEFI option ROMs are booted.
Only Legacy option ROMs are booted.
Fujitsu
Advanced Menu – Advanced system configuration
TPM (Trusted Platform Module) Computing
Trusted Computing
Platform Module
Opens the submenu for enabling TPM and changing the TPM settings. If this setup
menu is available, the system board contains a security and encryption chip (TPM Trusted Platform Module) which complies with TCG specification 1.2. This chip allows
security-related data (passwords, etc.) to be stored securely. The use of TPM is standardised
and is specified by the Trusted Computing Group (TCG).
TPM Support
Trusted Platform Module
Specifies whether the TPM (Trusted Platform Module) hardware is available. If the TPM is
disabled, the system behaves like any other system without TPM hardware.
Disabled
Enabled
Trusted Platform Module is not available.
Trusted Platform Module is available.
TPM State
Trusted Platform Module
Specifies whether TPM (Trusted Platform Module) can be used by the operating system.
Disabled
Enabled
Trusted Platform Module cannot be used.
Trusted Platform Module can be used.
Pending TPM operation
Trusted Platform Module
Specifies a TPM operation which will be performed during the next boot process.
None
No TPM operation will be performed.
Enable Take The operating system can assume ownership of the TPM.
Ownership
Disable Take The operating system cannot assume ownership of the TPM.
Ownership
TPM Clear TPM is reset to the factory setting. All keys in the TPM will be deleted.
Current TPM Status Information
Trusted Platform Module
Shows the current TPM (Trusted Platform Module) status.
TPM
SUPPORT
OFF
TPM
Enabled
Status
TPM Active
Status
TPM Owner
Status
Fujitsu
Is displayed if the TPM Support is disabled.
Indicates whether TPM can be used.
Indicates whether TPM is enabled.
Indicates the TPM owner status.
35
Advanced Menu – Advanced system configuration
USB Configuration
USB Devices
USB
Shows the number of available USB devices, USB keyboards, USB mice and USB hubs.
xHCI Mode
xHCIMode
Specifies the mode in which USB devices are operated at the USB 3.0 sockets marked in blue.
If using operating systems that do not support USB 3.0 (e.g. Windows XP),
it is recommended that you set xHCI mode to Disabled.
Smart Auto
Auto
Enabled
Disabled
Depending on whether or not the operating system used supports USB 3.0
(xHCI mode) or USB 2.0 (EHCI mode), the mode preset by the operating system
is automatically used for any subsequent system boots, provided the system
was not disconnected from the power supply. For the Smart Auto setting, it is
recommended that you set the Low Power Soft Off setup point to Disabled.
During the BIOS POST, USB 3.0 devices work in USB 2.0 mode. Operating
systems which support USB 3.0 switch to USB 3.0 during booting of the
operating system.
During the BIOS POST, all USB 3.0 devices are operated in USB 3.0 mode. For
operating systems which do not support USB 3.0, these devices are no longer
available in the operating system.
USB 3.0 devices work in USB 2.0 mode both in the BIOS POST and under
the operating system.
Legacy USB Support
LegacyUSBSupport
Specifies whether legacy USB support is available. This function should always be enabled or
set to Auto so that the operating system can be booted from a USB device if required.
Disabled
Enabled
Auto
Legacy USB support is not available. A USB keyboard or USB mouse
can only be used if this is supported by the operating system. Booting the
operating system from a USB device is not possible.
Legacy USB support is available. A USB keyboard or USB mouse can
also be used if the operating system does not support USB. Booting the
operating system from a USB device is possible.
Legacy USB support will be disabled if no USB devices are connected.
Legacy USB support should be disabled if the operating system supports USB and
you do not want to boot the operating system from USB devices.
36
Fujitsu
Advanced Menu – Advanced system configuration
Mass Storage Devices
List of USB Mass Storage Device(s)
Mass StorageDevices
Allows the user to force a particular device emulation. When set to Auto, the devices
are emulated according to their media format. Optical drives are emulated as "CD ROM"
and drives without data media according to the drive type.
Auto
Emulation is chosen depending on the USB device.
Force USB floppy emulation.
Force USB hard disk emulation.
Force USB CD ROM emulation.
Floppy
Hard Disk
CD-ROM
USB Port Security
USB
Opens the USB Port Security submenu in order to configure the USB
interfaces present on the mainboard.
USB Port Control
Configures the use of the USB ports. Disabled USB ports are only available during the
POST, but are no longer available under the operating system.
During POST, a USB mouse and a USB keyboard are also available if
the corresponding USB port is disabled.
Enable all ports
Disable all ports
Enable front and
internal ports
Enable rear and
internal ports
Enable internal
ports only
Enable used ports
All USB ports are enabled.
All USB ports are disabled.
All USB ports on the rear of the device are disabled.
All USB ports on the front of the device are disabled.
All external USB ports are disabled.
All unused USB ports are disabled.
If Enable rear and internal ports is enabled, all the USB ports on the front of the device
are also disabled during POST. in this case, it is not possible to call the BIOS Setup
using a USB keyboard which is connected to a USB port on the front of the device.
Fujitsu
37
Advanced Menu – Advanced system configuration
USB Device Control
USB
For the Enable front and internal ports, Enable rear and internal ports and Enable used ports settings,
which were made under USB Port Control, there are additional options available here.
Enable all devices
Enable Keyboard
and Mouse only
Those settings made under USB Port Control will be used without any limitation.
Only USB keyboards and USB mice can be operated at the USB ports
enabled under USB Port Control. Any ports to which no USB keyboards or
USB mice are connected are disabled. Keyboards with an integrated hub
result in deactivation of the port.
Enable all devices USB ports on which USB storage devices or USB hubs are connected will
except mass storage be disabled.
devices/Hubs
System Management
Only for versions D3348 and D3358.
System Name
Shows the name of the system.
Firmware Version
Shows the firmware version of the system monitoring controller.
SMCS Version
Shows the SMCS version (Systemboard Management Configuration Settings).
Fan Control
Controls the speed of the fan. The preset mode can be changed depending on
the system configuration and the applications used.
Enhanced
Auto
Full
38
The fan speed will be increased automatically so that the maximum CPU
performance is achieved.
The fan speed is adjusted automatically. A compromise between system
temperature and CPU performance.
All fans are operated at maximum speed.
Fujitsu
Advanced Menu – Advanced system configuration
Super IO Configuration
Super IO Chip
SuperIOConfiguration
Shows information about the Super IO Chip.
Serial Port 1 Configuration
Opens the submenu for configuration of the serial port 1 (COMA).
Serial Port
Specifies whether the serial port is available.
Disabled
Enabled
The serial port is not available.
The serial port is available.
Device Settings
Shows the base I/O address and the interrupt used for access to the parallel port.
Change Settings
Specifies which base I/O addresses and which interrupts can be used for the particular
serial port by the BIOS or the operating system.
Auto
IO=3F8h; IRQ=4;
IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12;
The base I/O address and the interrupt are automatically
assigned.
The base I/O address 3F8h and the interrupt 4 are
permanently assigned.
The base I/O address is permanently assigned.
IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12;
IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12;
IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12;
The values given in the list are available for the interrupt for automatic selection
by the BIOS or the operating system.
If conflicts with other devices occur, this option should be converted to Auto.
Fujitsu
39
Advanced Menu – Advanced system configuration
Serial Port Console Redirection
Only for versions D3348 and D3358.
Serialinterface
The parameters for terminal communication via Serial Port Console Redirection can be shown
and set in this submenu. Some parameters are only available under certain conditions.
Console Redirection Settings (for COM0 and COM4)
COM1
COM0
Specifies the data exchange process of the host and remote system via the COM0
and COM4 ports (iAMT/SOL (Serial overLAN)).
Both systems require identical or compatible settings.
Terminal Type
Specifies the type of terminal.
Permitted values: VT100, VT100+, VT-UTF8, ANSI
The terminal type allocated will be used to transfer data to the host.
Bits per Second
Specifies the transfer rate for communication with the host.
Permitted values: 9600, 19200, 38400, 57600, 115200
The data will be transferred to the host at the transfer rate set.
Data Bits
Shows the number of data bits used for communication with the host.
7
8
40
Seven data bits are used for the communication.
Eight data bits are used for the communication.
Fujitsu
Advanced Menu – Advanced system configuration
Parity
Specifies the use of parity bits for communication with the host. Parity bits are used for error detection.
None
Even
Odd
Mark
Space
No parity bits are used. Error detection is not possible.
Parity bit is 0 if the number of ones in the data bit is an even number.
Parity bit is 0 if the number of ones in the data bit is an odd number.
Parity bit is always 1.
Parity bit is always 0.
Stop Bits
Shows the number of stop bits used to indicate the end of a serial data packet.
1
2
One stop bit is used.
Two stop bits are used.
Flow Control
This setting determines the transfer control over the interface.
None
The interface is operated without transfer control.
Hardware CTS/RTS The transfer control is undertaken by the hardware. This mode must also
be supported by the cable.
AMT Configuration
AMTConfiguration
Opens the submenu to configure Intel® Active Management Technology.
ME Version
Shows the current AMT/ME version.
Unconfigure AMT/ME
If this option is enabled, an MBEx (Management Engine BIOS eXtension) query occurs at the next
reboot to establish whether the AMT/ME configuration should be reset to the default values.
Disabled
Enabled
Fujitsu
Do not change the AMT/ME configuration.
Start the reset of the AMT/ME configuration. The option is then automatically
reset to Disabled.
41
Advanced Menu – Advanced system configuration
MEBx Mode
Configure how the MEBx (Management Engine BIOS eXtension) behaves during the reboot.
Normal
Enter MEBx Setup
The message Ctrl + P to open the MEBx Setup will be displayed during
the POST.
The MEBx Setup will be automatically called during the next POST.
IFR Support
IndependentFirmwareRecovery
Specifies whether an automatic ME firmware update (Intel ® Independent Firmware Recovery
(IFR)) can be performed under an operating system via the ME driver.
Disabled
Enabled
The automatic ME firmware update under the OS is not available.
The automatic ME firmware update under the OS is available.
Network Stack
Network Stack
Specifies whether the UEFI Network Stack is available for network access under UEFI. If the
UEFI Network Stack is disabled, UEFI installation via PXE is not possible, for example.
Disabled
Enabled
The UEFI Network Stack is not available.
The UEFI Network Stack is available.
Ipv4 PXE Support
Specifies whether PXE UEFI Boot via Ipv4 is available for installation of
operating systems in UEFI mode.
Disabled
Enabled
PXE UEFI Boot via Ipv4 is not available.
PXE UEFI Boot via Ipv4 is available.
Ipv6 PXE Support
Specifies whether PXE UEFI Boot via Ipv6 is available for installation of
operating systems in UEFI mode.
Disabled
Enabled
42
PXE UEFI Boot via Ipv6 is not available.
PXE UEFI Boot via Ipv6 is available.
Fujitsu
Advanced Menu – Advanced system configuration
Option ROM Configuration
Calls the Option ROM Configuration submenu.
Launch Slot n OpROM
Specifies whether Option ROMs for expansion cards which are plugged into this slot should be started.
Disabled
Enabled
Do not start any Option ROMs for expansion cards in this slot.
Start Option ROMs for expansion cards in this slot.
UEFI Device Driver Setup
A UEFI device driver can support the interface to UEFI-FW Setup and makes information
and menu items available. Available UEFI device drivers are for example Intel®
Ethernet Connection I217-LM and Intel® I210 Gigabit.
Driver Health
If a UEFI driver of a PCI express device supports the Driver Health protocol, the UEFI firmware
can query the status of the devices with the UEFI drivers which they manage. The status
of the UEFI drivers which support Driver Health are shown in this menu.
Fujitsu
43
Security Menu – Security Functions
Security Menu – Security Functions
BIOS Setup,
SecurityMenu
The Security menu offers various options for protecting your system and personal
data from unauthorised access. Using a sensible combination of these options will
help you achieve maximum protection for your system.
The following security settings can be made in this menu. Some of them are
only available under certain conditions.
44
Fujitsu
Security Menu – Security Functions
Password Description
Password
Neither an administrator password nor a user password has been allocated
Opening the BIOS Setup and booting the system are possible without restriction.
Only the administrator password was allocated
If ONLY an administrator password was allocated, only the BIOS Setup is protected. Booting
the system can be performed without restriction. When you access the BIOS Setup with an
administrator password, the Administrator access level is assigned to you and you have unrestricted
access to the BIOS Setup. If you access the BIOS Setup without a password, access to the
BIOS Setup is limited because you are only assigned the User access level.
Administrator AND user passwords were allocated
If administrator and user passwords were allocated, the authorisation level in the BIOS Setup
depends on the password entered. If you access the BIOS Setup with the administrator password,
unlimited access to the BIOS Setup is possible, entry of the user password results in limited access.
Booting the system is possible both with the administrator and also with the user password.
If the administrator password is deleted, the user password will also be deleted.
The system will stop after an incorrect password has been entered three times. If this
happens, switch off the system and then back on again, and enter the correct password.
Administrator Password
Password
If you press the enter key, a window will open in which you can assign the administrator
password. Enter a character string to define the password. If you confirm an empty
password field, the password will be deleted.
To call up the complete BIOS Setup, you need the administrator level of
access. If an administrator password is allocated, the user password only
allows very limited access to the BIOS Setup.
User Password
Password
If you press the enter key, a window will open in which you can assign the user
password. Enter a character string to define the password. With the user password,
you can prevent unauthorised access to your system.
In order to be able to assign a user password, an administrator password
must already have been assigned.
Fujitsu
45
Security Menu – Security Functions
User Password on Boot
Password
Specifies whether a user password must be entered before the boot process.
On Every Boot
Disabled
Entry of a user password is required before every boot process.
The system starts without requiring the entry of a user password.
If the administrator password and the user password have been assigned and the
setting Disabled has been chosen for this item, simply press Enter to get USER access
to the BIOS Setup. In this case the user password does not have to be entered.
Skip Password on WOL
Password
Specifies whether a user password will be skipped or must be entered during
a system boot via Wake on LAN.
Disabled
Enabled
The user password must be entered via using the keyboard during the system
boot.
The user password is deactivated during the system boot with Wake On LAN.
FLASH Write
Writeprotection
Supplies the system BIOS with write protection.
Disabled
Enabled
The system BIOS cannot be written. A flash BIOS update is not possible
The system BIOS can be written. A flash BIOS update is possible.
HDD Security Configuration
HDD Password on Boot
Password
Specifies whether a hard disk user password must be entered during every boot process.
Disabled
Enabled
46
It is not necessary to enter a hard disk user password during the boot process.
Entry of a hard disk user password is required during every boot process.
Fujitsu
Security Menu – Security Functions
HDD n / HDD-ID
Opens a submenu with information on the hard disk user password.
HDD Password Description
Allows the hard disk user and master passwords to be set, changed and deleted. The
hard disk user password must be set up before the Enabled Security setting can be
carried out. The hard disk master password can only be changed if you have successfully
unlocked it in POST with the hard disk master password.
HDD Password Configuration
Shows the current security status of the hard disk.
Security Supported
Yes is shown here if the device supports use of a hard disk user password. In this
case it is possible to assign a password to the hard drive.
Security Enabled
Yes is shown here if either a hard disk user password or a hard disk master
password has been assigned to the hard disk.
Security Locked
The hard disk is locked if it was not unlocked with the valid password.
Security Frozen
If Yes is displayed, then a hard disk user password cannot be set up, changed or deleted. To
change the security frozen status to No, the system must have been shut down before the BIOS
Setup is called. Only then can a hard disk user password be set up, changed or deleted.
HDD User Password Status
Shows whether a hard disk user password was allocated or not.
HDD Master Password Status
Shows whether a hard disk master password was allocated or not.
Fujitsu
47
Security Menu – Security Functions
Set User Password
Password
The hard disk user password protects the hard disk(s) from unauthorised access. Booting the
operating system from the hard disk or accessing the data on the hard disk can only be carried out
by those people who know the hard disk user password. The hard disk user password can be up to
32 characters long. The settings become effective immediately and also remain so, regardless of
how you later end the BIOS Setup. The hard disk user password is requested during the POST.
If you press the Enter key, a window will open in which you can assign the
hard disk user password. Enter a character string to define the password. If you
confirm an empty password field, the password will be deleted.
Set Master Password
Password
If a hard disk user password has been forgotten, it can be deleted using the hard disk master
password. This option is only available if an incorrect hard disk user password has been
entered three times when the system is booting during POST. The hard disk master password
for your hard disk can be obtained from the certificated technical support service, but only if
the particular HDD-ID is provided together with a valid proof of purchase.
Secure Boot Configuration
SecureBoot
Opens the submenu for configuring Secure Boot.
An authentication process for the firmware version is defined with Secure Boot Configuration.
Secure Boot defines the industry standard method by which platform firmware certificates are
managed, firmware is authenticated and in which the operating system is integrated in this process.
Secure Boot Configuration is based on the PKI process (Public Key Infrastructure), to
authenticate modules before they are allowed to be executed.
Platform Mode
Platform Mode
SecureBoot
Shows whether the system is in user mode or setup mode.
User
Setup
In user mode, the Platform Key (PK) is installed. Secure Boot can be enabled
or disabled via the Secure Boot Control menu option.
In setup mode, the Platform Key (PK) is not installed. Secure Boot is disabled
and cannot be enabled via the Secure Boot Control menu option.
Secure Boot
SecureBoot
Indicates whether the Secure Boot function is active.
Not active
Active
48
Secure Boot is not active.
Secure Boot is active.
Fujitsu
Security Menu – Security Functions
Secure Boot Control
SecureBootControl
SecureBoot
Specifies whether booting of unsigned boot loaders/UEFI OpROMs is permitted.
The associated signatures are saved in the BIOS or can be reloaded
in the Key Management submenu.
Disabled
Enabled
All boot loaders / OpROMs (Legacy / UEFI) can be executed.
Only booting of signed boot loaders/UEFI OpROMs is permitted.
Secure Boot Mode
SecureBootMode
SecureBoot
Specifies whether the Key Management submenu is available.
Default
Custom
The Key Management submenu is not available.
The Key Management submenu is available.
Key Management
KeyManagement
SecureBoot
Submenu for deleting, changing and adding the key and signature databases required for Secure Boot.
Without the installed Platform Key (PK), the system is in setup mode (Secure
Boot is disabled). As soon as the PK is installed, the system switches
to user mode (Secure Boot can be enabled).
Factory Default Key Provisioning
KeyManagement
If the system is in setup mode (no Public Key is installed), it is possible to install
the default Secure Boot key and signature databases.
Disabled
Enabled
The available Secure Boot key and signature databases remain unchanged.
If the PK, KEK, DB, DBT, DBX signature databases are not available, the
default Secure Boot key and signature databases will be installed after
rebooting the system.
Delete All Secure Boot Variables
KeyManagement
Puts the system in setup mode (Secure Boot is disabled). All keys and signature
databases (PK, KEK, DB, DBT, DBX) in the system are deleted.
This menu item is only available if Factory Default Key Provisioning is set to Disabled.
Fujitsu
49
Security Menu – Security Functions
Enroll All Factory Default Keys
KeyManagement
All keys and signature databases (PK, KEK, DB, DBT, DBX) in the system
are reset to the default values.
This menu item is only available if Factory Default Key Provisioning is set to Disabled.
Save Secure Boot Keys
SecureBootKeys
KeyManagement
Saves the Secure Boot Key and Key Databases to the selected drive.
Platform Key
Platform Key(PK)
KeyManagement
Shows the current status of the Platform Key (PK).
Installed
Not Installed
The PK is installed. System is in user mode.
The PK is not installed. The system is in setup mode.
Delete PK
Platform Key
KeyManagement
Deletes the Platform Key (PK), which puts the system in setup mode and disables Secure Boot.
Set new PK
Platform Key
KeyManagement
Sets the Platform Key (PK). After selecting the drive, the corresponding file
must be selected in the browser.
Key Exchange Key
Key(KEK)
KeyManagement
KeyExchange
Shows the current status of the Key Exchange Key Database (KEK).
Installed
Not installed
The KEK Database is installed.
The KEK Database is not installed.
Delete KEK
KeyExchange Key(KEK)
KeyManagement
Deletes the Key Exchange Key Database (KEK)
Set new KEK
KeyExchange Key(KEK)
KeyManagement
Sets the Key Exchange Key Database (KEK) After selecting the drive, the
corresponding file must be selected in the browser.
50
Fujitsu
Security Menu – Security Functions
Append KEK
KeyExchange Key(KEK)
KeyManagement
Adds an entry to the Key Exchange Key Database (KEK). After selecting the drive,
the corresponding file must be selected in the browser.
Authorized Signatures
AuthorizedSignature Database(DB)
KeyManagement
Shows the current status of the Authorized Signature Database (DB).
Installed
Not installed
The DB is installed.
The DB is not installed.
Delete DB
AuthorizedSignature Database(DB)
KeyManagement
Deletes the Authorized Signature Database (DB).
Set new DB
AuthorizedSignature Database(DB)
KeyManagement
Sets the Authorized Signature Database (DB). After selecting the drive, the
corresponding file must be selected in the browser.
Append DB
AuthorizedSignature Database(DB)
KeyManagement
Adds an entry to the Authorized Signature Database (DB). After selecting the drive,
the corresponding file must be selected in the browser.
Authorized TimeStamps
Shows the current status of the Authorized TimeStamps Database (DBT).
Installed
Not installed
The DBT is installed.
The DBT is not installed.
Delete DBT
AuthorizedSignature Database(DBT)
KeyManagement
Deletes the Authorized Signature Database (DBT).
Set new DBT
AuthorizedSignature Database(DBT)
KeyManagement
Sets the Authorized Signature Database (DBT). After selecting the drive, the
corresponding file must be selected in the browser.
Append DBT
AuthorizedSignature Database(DBT)
KeyManagement
Adds an entry to the Authorized Signature Database (DBT). After selecting the drive,
the corresponding file must be selected in the browser.
Fujitsu
51
Security Menu – Security Functions
Forbidden Signatures
Forbidden SignatureDatabase(DBX)
KeyManagement
Shows the current status of the Forbidden Signature Database (DB).
Installed
Not installed
The DBX is installed.
The DBX is not installed.
Delete DBX
Forbidden SignatureDatabase(DBX)
KeyManagement
Deletes the Forbidden Signature Database (DB).
Set new DBX
Forbidden SignatureDatabase(DBX)
KeyManagement
Sets the Forbidden Signature Database (DB). After selecting the drive, the
corresponding file must be selected in the browser.
Append DBX
Forbidden SignatureDatabase(DBX)
KeyManagement
Adds an entry to the Forbidden Signature Database (DBX). After selecting the drive,
the corresponding file must be selected in the browser.
52
Fujitsu
Power Menu – Energy saving functions
Power Menu – Energy saving functions
Example showing the Power menu.
Power Settings
Power On Source
Specifies whether the switch-on sources for the system are managed via BIOS
or via an ACPI operating system.
BIOS Controlled
ACPI Controlled
Fujitsu
The switch-on sources are managed via BIOS.
The switch-on sources are managed via the ACPI operating system.
53
Power Menu – Energy saving functions
Low Power Soft Off
Only for versions D3348 and D3358.
Reduces the energy consumption of a system which is switched off.
When Low Power Soft Off is enabled, the system can only be switched on with
the power button on the casing. The device cannot be switched on using the
power button of a USB keyboard or a Wake-on-LAN signal.
Disabled
Enabled
Low Power Soft Off is disabled.
Low Power Soft Off is enabled.
Power Failure Recovery – System status after a power failure
Only for versions D3348 and D3358.
Power failure,system reaction
Specifies how the system behaves during a reboot following a power failure.
Always Off
The system switches on briefly, performs a status check (initialisation), and
then switches off.
Always On
Previous State
Disabled
The system switches on.
The system switches on briefly, performs a status check, and then returns the
mode it was in before the power failure occurred (ON or OFF).
The system does not switch on.
Hibernate like Soft Off
In order to also reduce the energy consumption in hibernate mode (S4), the system will instead
be brought into Low Power Soft Off or Zero Watt mode (S5) when it is switched off. However, the
energy consumption will only reduce if Low Power Soft Off or Zero Watt mode is enabled.
Disabled
Enabled
54
The system will be brought into hibernate mode (S4).
Instead of going into hibernate mode (S4), the system will be brought into Low Power
Soft Off or Zero Watt mode (S5).
Fujitsu
Power Menu – Energy saving functions
USB At Power Off
Enables/disables the power supply for the USB ports. This option is only available if
Low Power Soft Off and Zero Watt mode are disabled.
Always off The USB ports are no longer supplied with power after the system is shut down.
Always on The USB ports continue to be supplied with power after the system is shut down.
Wake-Up Resources
This submenu is only available if neither Zero-Watt mode nor Low Power Soft Off is enabled.
LAN
System power-on
Determines whether the system can be switched on via a LAN controller (on
the system board or expansion card).
Enabled
Disabled
The system can be switched on via a LAN controller.
The system cannot be switched on via a LAN controller.
Wake On LAN Boot
Switch onsystem
Specifies the system behaviour when switched on by means of network signals.
Boot
Sequence
Force LAN
Boot
After being switched on via the LAN, the system boots up according to the device
sequence specified in the boot menu.
After being switched on via the LAN, the system is booted remotely via the LAN.
Wake Up Timer
Wake UpTimer
The time at which the system should be switched on can be specified here.
Disabled
Enabled
Wake Up Timer is not enabled.
Wake Up Timer is enabled. The system is switched on at the time specified.
Hour
Specifies the hour of the switch-on time.
Minute
Specifies the minute of the switch-on time.
Fujitsu
55
Power Menu – Energy saving functions
Second
Specifies the second of the switch-on time.
Wake Up Mode
Wake UpMode
Specifies whether the system should be switched on daily, on selected week days
or only once a month at the specified time.
Daily
Weekly
Monthly
The system will be switched on daily at the time specified.
The system is switched on at the specified time on the selected week days.
The system will be switched on once a month at the time specified.
Wake Up Day
Specifies the day of the month on which the system is to be switched on. Permitted values are 1..31.
USB Keyboard
USB
Specifies whether the system can be switched on via the network key of a USB
keyboard, if the keyboard supports this function.
Switching on the system via a USB keyboard is only available if USB
At Power-Off is set toAlways On.
Disabled
Enabled
56
The network key of the USB keyboard is disabled.
The network key of the USB keyboard is enabled.
Fujitsu
Event Logs – Configuration and Display of the Event Log
Event Logs – Configuration and
Display of the Event Log
Example showing the Event Logs.
Only for versions D3348 and D3358
Change SMBIOS event log settings
SMBIOS Event Log
EventLog
Specifies whether the SMBIOS event log is enabled.
Disabled
Enabled
Fujitsu
The SMBIOS event log is disabled.
The SMBIOS event log is enabled.
57
Event Logs – Configuration and Display of the Event Log
Erase Event Log
Specifies whether the SMBIOS event log should be deleted.
No
Yes, next reset
Yes, every reset
The SMBIOS event log will not be deleted.
The SMBIOS event Log is deleted once during the next system boot up.
Afterwards, this option is automatically reset to No.
The SMBIOS event log is deleted every time the system is booted.
When Log is full
Specifies the course of action to be taken when the SMBIOS event log is full.
Do Nothing
Erase Immediately
When the SMBIOS event log is full, no further entries are added. The SMBIOS
event log must first be deleted before new entries can be added.
When the SMBIOS event log is full, it will be erased immediately. All existing
entries will be deleted!
Log System Boot Event
Specifies whether every boot of the system is logged in the SMBIOS event log.
Disabled
Enabled
System boots are not recorded in the SMBIOS event log.
All system boots are recorded in the SMBIOS event log.
MECI
Multiple Event Count Increment: the number of double events which must occur
before the multiple event counter is updated, including the associated log entry.
The value is in the range between 1 and 255.
METW
Multiple Event Time Window: the number of minutes which must elapse between double event logs
which use a multiple event counter. The value is in the range between 0 to 99 minutes.
Log OEM Codes
Enables or disables the log function of EFI codes as OEM codes (if not already legacy converted).
Convert OEM codes
Enabling or disabling the conversion of EFI status codes to standard SMBIOS
types (not all may be translated).
58
Fujitsu
Event Logs – Configuration and Display of the Event Log
View SMBIOS Event Log
Opens the submenu to show all SMBIOS event log entries present.
Fujitsu
59
IPMI Management
IPMI Management
IPMIManagement
The following parameters can be set in this menu. Some of these parameters
are only available under certain conditions.
Asset tag
Indicates the asset tag field of SMBIOS type 3 (system casing or chassis). To set or change the
asset tag, select this setup option and press the enter key. A window will open in which you can
type in a new character string or change the current one. The input must be alphanumeric.
Onboard Video
The graphics controller on the system board can be disabled if a graphics card is installed.
Disabled
Enabled
60
The graphics controller on the system board is disabled.
The graphics controller on the system board is enabled.
Fujitsu
IPMI Management
Boot Retry Counter: Number of attempts
Specifies the maximum number of attempts that can be made to boot the operating system.
Each unsuccessful attempt is ended by a system reboot after the time set under the Boot
Watchdog expires. Other critical system errors also result in system reboot and a decrease in
the counter reading. After the last attempt, the system will be permanently disabled.
The permitted values are: 0 to 7 possible attempts
► To increase the value, press the + button on the number pad. To decrease
the value, press the - button.
Power Cycle Delay
Specifies the minimum time that must pass until the system can be switched
on again after being switched off.
The permitted values are: 0 to 15 seconds.
► To increase the value, press the
the value, press the - button.
+
on the number pad. To decrease
ASR&R Boot Delay
Specifies the boot delay after shutdown due to a fault (e.g. excessively high temperature).
The system is rebooted after the set wait period has expired.
The permitted values are: 1 min to 30 mins
► To increase the value, press the
the value, press the - button.
+
on the number pad. To decrease
Temperature Monitoring
Temperaturemonitoring
This field specifies whether the system will be switched off if the ambient temperature or the
temperature of a processor exceeds the critical value. This protects against damage to the system
or data. If the operating system has an active server management process, this takes over the
temperature monitoring function and performs a shutdown if critical temperatures occur.
Depending on the Boot Retry Counter, the system switches itself on again after the period specified
under ASR&R Boot Delay. In the meantime the system should have cooled down again.
Disabled
Enabled
Fujitsu
The system does not switch itself off if the temperature exceeds the critical
value.
The system switches itself off if the temperature exceeds the critical value.
61
IPMI Management
Event Log Full Mode
EventLog
Specifies whether the System Event Log can be overwritten.
Overwrite
If the System Event Log is full, further events overwrite the oldest entries in
the System Event Log. More recent events have greater importance than
older ones in this case.
If the System Event Log file is full, no further events are entered. The System
Event Log file must be cleared first before additional events can be entered.
Older events have greater importance than newer ones in this case.
Maintain
Load iRMC Default Values
iRMC
Specifies whether the iRMC Default Values should be loaded.
No
Yes
No action is taken.
By leaving the BIOS Setup through Save Changes & Exit, the iRMC Default
Values are loaded. The BIOS Setup settings that concern the iRMC are not
lost by using this option. After loading the iRMC Default Values, they are sent
to the iRMC and thus overwrite the corresponding values. The setting will
automatically be set on ’No’ after loading the Default Values.
Power Failure Recovery - system status
after a power failure
Power failure
Specifies how the system behaves during a reboot caused by failure of the power supply.
Always Off
Previous State
Always On
The system checks its status and then switches itself off.
The system checks its status and then goes back into the status it was in
before the power failure occurred (On or Off).
The system checks its status and then switches itself on. For the planned UPS
operation set Always On. Otherwise the workstation may not be turned on
at the specified time.
All wake up sources are reconfigured during the short initialisation phase.
The system can be re-awakened by LAN etc.
Serial Multiplexer
iRMC
Serialinterface
Specifies whether the serial interface can be used by the system.
System
iRMC
62
The serial interface can be used by the system or the operating system.
The serial interface can be used only by the iRMC. The operating system
cannot use this serial interface.
Fujitsu
IPMI Management
Boot Watchdog
Operatingsystem boot
Specifies whether the operating system should reboot if the server management system (ServerView
Agent) cannot establish a connection to iRMC. After a successful operating system boot and
within a set period of time, the ServerView Agent starts to communicate with the iRMC. If the time
period is exceeded, the iRMC assumes there is a boot error and can restart the system.
Disabled
The iRMC does not perform a system restart with a Boot Watchdog. If
ServerView is not installed, this parameter must be selected to prevent an
unintentional restart of the system.
The iRMC performs a system restart when there is an O/S boot timeout,
because it assumes a boot error.
Enabled
If Enabled is specified, the server may not run properly. The server
can for instance automatically shut down or restart, without previously
having received an appropriate command.
If you boot the system via the ServerView suite, you must disable the Boot Watchdog,
including if ServerView Agent was installed on the system. If this component is enabled
during the boot, the server may not run properly. The server can for instance automatically
shut down or restart, without previously having received an appropriate command.
When configuring this function, please take note of the instructions in
the manuals for the ServerView suite.
Timeout Value
Specifies the time after which a system restart is performed, if this is enabled by Boot Watchdog.
The permitted values are: 1 to 100
1...100
The system is restarted after the set time (minutes) has elapsed.
► To increase the value, press the
the value, press the - button.
+
on the number pad. To decrease
Action – action when time monitoring expires
Timemonitoring
Determines the action performed after the boot watchdog expires.
Continue
Reset
Power cycle
The system continues to run.
The system restarts.
The system switches off and then on again.
iRMC Lan Parameters Configuration
iRMC
The following parameters can be set in this menu. However, some of them
are only available under certain conditions.
Fujitsu
63
IPMI Management
Management LAN
Specifies the status of the LAN interface that can be used by the iRMC.
Disabled
Enabled
The iRMC LAN interface is disabled.
The iRMC LAN interface is enabled.
iRMC MAC Address
Indicates the MAC address of the iRMC. The iRMC MAC address is divided into
blocks which are separated from each other by a colon.
Management LAN Speed
Specifies the speed for the Management LAN interface.
Auto
100 Mbit/s Full
Duplex
100 Mbit/s Half
Duplex
10 Mbit/s Full
Duplex
10 Mbit/s Half
Duplex
1000 Mbit/s
The speed is managed automatically by the LAN Controller.
The maximum speed is 100 Mbit/s. Simultaneous transmission in both
directions is possible.
The maximum speed is 100 Mbit/s. Transmission is only possible in one
direction at a time.
Fixed speed at 10 Mbit/s. Simultaneous transmission in both directions is
possible.
Fixed speed at 10 Mbit/s. Transmission is only possible in one direction at a
time.
The maximum speed is 1000 Mbit/s.
VLAN ID tagging
Enables support of IEEE 802.1q VLAN headers (virtual LAN) for IPMI over
IP sessions on IEEE 802.3 Ethernet.
Disabled
Enabled
Disables support of IEEE 802.1q VLAN headers (virtual LAN) for IPMI over
IP sessions on IEEE 802.3 Ethernet.
Enables support of IEEE 802.1q VLAN headers (virtual LAN) for IPMI over
IP sessions on IEEE 802.3 Ethernet.
VLAN ID
Value with which the VLAN Header is tagged.
The permitted values are: 0 ... 4094
VLAN Priority
Value for the VLAN user priority field to be used.
The permitted values are: 0 ... 7
64
Fujitsu
IPMI Management
iRMC IPv4 LAN stack
Configures whether the IPv4 LAN stack is available for the iRMC.
Disabled
Enabled
The IPv4 LAN stack is not available for the iRMC.
The IPv4 LAN stack is available for the iRMC.
IP Configuration
Specifies whether the DHCP support (Dynamic Host Configuration Protocol) for the iRMC is
used. The iRMC can automatically have itself assigned an IP address from a DHCP server in
the network via the DHCP (Dynamic Host Configuration Protocol) network protocol.
Use DHCP
Use static
configuration
DHCP support for the iRMC is used. Local IP address, subnet mask and
gateway address are requested by the DHCP server.
DHCP support is not used for the iRMC. Local IP address, subnet mask and
gateway address must be input manually.
IP Address
Specifies the IP address of the iRMC.
Only numeric characters from 0-255 are permitted.
Subnet Mask
Finds the subnet mask address of the iRMC. Uses the same subnet mask as the operating system.
Only numeric characters from 0-255 are permitted.
Gateway address
Specifies the gateway address of the iRMC.
Only numeric characters from 0-255 are permitted.
iRMC IPv6 LAN Stack
Configures whether the IPv6 LAN stack is available for the iRMC.
Disabled
Enabled
The IPv6 LAN stack is not available for the iRMC.
The IPv6 LAN stack is available for the iRMC.
Link Local Address
Indicates the IPv6 address. The IP address is divided into blocks which are
separated from each other by a colon.
Fujitsu
65
IPMI Management
IPv6 Gateway
Shows the IPv6 gateway address. The IP Gateway address is divided into blocks
which are separated from each other by a colon.
Console Redirection (CR)
ConsoleRedirection
The following parameters can be set in this menu. However, some of them
are only available under certain conditions.
Console Redirection
ConsoleRedirection
Specifies the transfer rate for communication with the terminal.
Disabled
Serial 1
The terminal interface is disabled.
The terminal uses the first serial interface.
Baud rate
Interface baud rate
Specifies the transfer rate for communication with the terminal. The setting must
be the same on both the terminal and the server.
The permitted values are: 9600, 19.2 K, 38.4 K, 57.6 K, 115.2 K
Data communication with the terminal is performed at the rate set.
Protocol
Interface baud rate
Indicates the configured console type. This setting must be identical on
both the terminal and the server.
The permitted values are: VT100, PC ANSI, VT100+, VT-UTF8
Data communication with the terminal is performed with the configured console.
Flow Control - interface settings
Interface settings
This setting determines how the transfer via the port is controlled. The setting must
be the same on both the terminal and the server.
None
CTS/RTS
66
The interface is operated without transfer control.
The port transfer control is carried out by hardware. This mode must also
be supported by the cable.
Fujitsu
Boot Menu – System boot
Boot Menu – System boot
Bootmenu
The sequence of the drives from which booting is to occur can be specified here.
Up to eight drives (can include USB ports, for example) can be listed here.
Boot Configuration
Bootup NumLock State
NumLock
The setting of the NumLock function after a system boot is provided here. NumLock
controls the functionality of the numeric keypad.
On
Off
NumLock is enabled, the numeric keypad can be used.
NumLock is disabled, the numeric keypad keys can be used to control the cursor.
The Num indicator light on your keyboard shows the current boot up NumLock state.
The Num key on the keyboard can be used to toggle between ON and OFF.
Fujitsu
67
Boot Menu – System boot
Quiet Boot
The boot logo is shown on the screen instead of the POST boot up information.
Enabled
Disabled
The boot logo is displayed.
The POST boot up information is shown on the screen.
Check Controller Health Status
If a UEFI driver option ROM of a PCI Express device supports Controller Health, the UEFI firmware
can query the UEFI driver option ROM regarding the status of the devices that it manages.
Disabled
Enabled
The Controller Health Status is not queried by the UEFI FW.
The UEFI FW queries the Controller Health Status.
PXE Boot Option Retry
NON-EFI boot options based on PXE are repeated without waiting for user input.
Disabled
Enabled
NON-EFI boot options are not repeated without user input.
NON-EFI boot options are repeated without waiting for user input.
Boot Error Handling
Specifies whether the system boot process is interrupted and the system
stopped when an error is detected.
Continue
The system boot is not aborted. The error will be ignored, as far as this
is possible.
Pause and wait for If an error is detected during POST, the boot process is interrupted and the
key
system stopped.
Primary Display
PrimaryDisplay
Only for versions D3348 and D3358.
Specifies which plug-in graphics card is used as image source during the Power-On Self-Test (POST).
Slot n
68
Select the slot of the plug-in graphics card which should be used as image
source during POST.
Fujitsu
Boot Menu – System boot
Boot Removable Media
Specifies whether booting via a removable data storage device such as a USB stick is supported.
Disabled
Enabled
Booting via a removable data storage device is disabled.
Booting via a removable data storage device is enabled.
Virus Warning
Only for versions D3348 and D3358.
Checks the boot sectors of the hard disks for changes since the last system boot. If the boot sectors
have been changed without any apparent reason, a suitable virus detection program should be run.
Disabled
Enabled
Confirm
The boot sectors will not be checked.
If the boot sector has been changed since the last system boot (e.g. new
operating system or a virus attack), a warning notice is displayed. The warning
notice remains on the screen until you confirm the changes by going into BIOS
Setup and setting this item to Confirm or disable the function.
Confirm a required change to a boot sector (e.g. new operating system).
Boot option priorities
Displays the current boot sequence.
► Use the cursor keys
or
to select the device whose boot
sequence you would like to change.
► To increase the priority for the selected device, press the + key. To
decrease the priority, press the - key.
► To remove the selected device from the boot sequence, press the Enter key and select Disabled.
Fujitsu
69
Save & Exit Menu – Finish BIOS Setup
Save & Exit Menu – Finish BIOS Setup
Finish
ExitMenu
The Exit menu provides options for saving settings and exiting BIOS Setup.
Save Changes and Exit
Save ChangesandExit
To save the current entries in the menus and exit the BIOS Setup, select Save Changes
and Exit and then Yes. The new settings become effective and POST continues, provided
a reboot is not necessary due to a changed option.
Discard Changes and Exit - quit without saving
DiscardChangesand Exit
To discard the changes made since calling up the BIOS Setup or since the last
time the function "Save Changes" was called, select Discard Changes & Exit and
Yes. BIOS Setup is terminated and POST continues.
Save Changes and Reset
To save the current entries in the menus and exit BIOS Setup, select Save Changes and
Reset and Yes. The system reboots and the new settings take effect.
70
Fujitsu
Save & Exit Menu – Finish BIOS Setup
Discard Changes and Reset
To discard the changes made since calling up the BIOS Setup or since the last
time the function "Save Changes" was called, select Discard Changes and Reset and
Yes. BIOS Setup is closed and the system reboots.
Save Options
Save Changes
To save the changes made so far without leaving BIOS Setup, select Save Changes and Yes.
Discard Changes
To discard the changes made since calling the BIOS Setup or since the last time the function "Save
Changes" was called, but without leaving the BIOS Setup, select Save Changes and Yes.
Restore Defaults
To reset all the menus of the BIOS setup to the default values, select Restore Defaults and Yes. If
you wish to leave the BIOS Setup with these settings, select Save Changes and Exit and Yes.
Save as User Defaults
To save the changes made so far as user default settings, select Save as User Defaults and Yes.
Restore User Defaults
To reset all the menus of the BIOS Setup to the user default settings, select Restore User Defaults and
Yes. If you wish to leave the BIOS Setup with these settings, select Save Changes and Exit and Yes.
Boot Override
Use the cursor keys
and
to select the drive from which the operating system should
be booted. Press the Enter key to start the boot process from the selected drive.
Fujitsu
71
Save & Exit Menu – Finish BIOS Setup
Diagnostic Program
► To perform a basic test of the CPU, working memory and hard disks, select
Diagnostic Program and press the Enter key.
If
a problem occurs during the test, the relevant Error Code and a brief explanation (Diagnostic
Result) will be displayed. In addition, the Error Code is entered in the Smbios Event Log.
Diagnostic Program can also be called up directly in the Boot Menu
by pressing the F12 key in the POST.
72
Fujitsu
BIOS Update
BIOS Update
BIOS Update
To carry out a Flash BIOS Update, you can use the Auto BIOS Update function ("Auto BIOS
Update", Page 18) or must first download the necessary files from the Internet.
The BIOS is installed on a flash memory module. If an error occurs during the
flash BIOS update procedure, the BIOS image may be destroyed. You can then
only recover the BIOS using BIOS Recovery Update, see"BIOS Recovery Update",
Page 75. If this is not possible, the Flash memory module must be replaced. If this
is the case, please contact the Service Desk of Customer Services.
► On the Internet, go to "http://www.fujitsu.com/de/support/index.html".
► Use MANUAL PRODUCT SELECTION to select your device or look for your device under SELECT
PRODUCT USING SERIAL/IDENT NO. using the serial/ident. no. or the product name.
► Click on Drivers & Downloads and select your operating system.
► Select Flash BIOS.
► Flash BIOS Update – Desk Flash Instant: For "Flash-BIOS Update under Windows",
download the file Flash-BIOS Update – Desk Flash Instant.
► Admin package – Compressed Flash Files: If you cannot find the operating system which
you are using in the selection, select an operating system of your choice and download the
file Admin package – Compressed Flash Files to "Flash-BIOS Update using a USB stick".
► For safety reasons, make a note of the settings in the BIOS Setup before you perform the
Flash-BIOS update. Normally, a Flash-BIOS update does not damage the BIOS Setup.
Auto BIOS Update
Update
With Auto BIOS Update it is possible to check a Fujitsu server automatically to see if there is a new
BIOS version for the system. For the update, no operating system or external storage medium is
required. For details on the Auto BIOS Update function, see the manual, "Auto BIOS Update", Page 18.
Flash BIOS update under Windows
► Start your system and boot Windows.
► Open Windows Explorer, then under Flash-BIOS Update – Desk Flash Instant
select the file which was downloaded and start the Flash-BIOS update with a
double-click. Follow the instructions on the screen.
Administrator rights are necessary to run "Desk Flash Instant".
BIOSupdate
After the Flash-BIOS Update has terminated successfully, the system will restart
automatically and boot up with the new version of BIOS.
Fujitsu
73
BIOS Update
Flash BIOS update with a USB stick
► Have a boot-capable USB stick ready.
If your USB stick is not boot-capable, you will find the necessary files for it under
Admin package – Compressed Flash Files under the item Installation description then
selecting the item Further information. Follow the instructions.
BIOSupdate
When a boot-capable USB stick is created, all the files on the stick are
irretrievably deleted. Please therefore make certain that all files from the
USB stick are backed up elsewhere beforehand.
► Unzip the ZIP files which were downloaded under Admin package – Compressed Flash Files and
copy the files and directories into the root directory of your boot-capable USB stick.
► Restart your system and wait until screen output appears. Press the function key F12 and
or
to select the boot-capable USB stick.
use the cursor keys
► Use cd DOS to change directory, launch Flash BIOS Update with the command
DosFlash and follow the further instructions.
After the Flash-BIOS Update has terminated successfully, the system will restart
automatically and boot up with the new version of BIOS.
74
Fujitsu
BIOS Update
BIOS Recovery Update
BIOS RecoveryUpdate
RecoveryUpdate
► Prepare a boot-capable USB stick as described under "Flash BIOS update with a USB stick".
► Switch off the system and unplug it from the mains supply.
► Open the casing and enable Recovery using the jumper / DIP switch on the system board.
You will find details on this in the technical manual for the system board.
► Connect the prepared USB stick and remove all other bootable USB devices.
If the Admin package on the prepared USB stick does not match the BIOS
version of the system (e.g. Admin package for BIOS R1.2.0, but BIOS R1.3.0 is
enabled on the system), no screen outputs will be possible in recovery mode. The
Recovery Update will be carried out automatically in this case.
During the Recovery Update, a recurring short signal tone will sound. Recovery of the
system has succeeded if you hear the repeated signal sequence "short-short-long-long"
after a long signal tone. The Recovery process can take a few minutes.
► Connect the system to the mains supply again and switch it on.
► Use cd DOS to change directory, launch BIOS Recovery Update with the command
DosFlash and follow the further instructions.
► After the recovery process has finished, switch off the system and
disconnect it from the mains supply.
► Remove the USB stick.
► For all jumpers / DIP switches which were changed, return them to their
original positions and close the casing.
► Connect the system to the mains supply again and switch it on.
The system will now boot up with the new version of BIOS.
► Check the settings in the BIOS Setup. If necessary, configure the settings once again.
Fujitsu
75
Index
Index
A
Access 14
Access Level 14
Acoustic Management 33
Acoustic Mode 33
Active Processor Cores 23
Adjacent Cache Line Prefetcher 24
Advanced menu 15
Aggressive Link Power Management 31
AMT Configuration 41
Audio Configuration 18
Authorized Signature Database (DB) 51
Authorized Signature Database (DBT) 51
Automatic BIOS Update 18–19
B
BIOS Recovery Update 75
BIOS Setup 11
navigating 12
settings 9
System configuration 13
System settings 15
BIOS Setup,
security functions 44
BIOS update
under Windows 73
with a USB stick 74
BIOS Update 73
BIOS-Setup
opening 11
Boot menu 11–12
system boot 67
Boot Menu
Calling the 11
Boot Option Filter 34
C
COM0 40
COM1 40
Console Redirection 66
CPU C1E Support 27
CPU C3 Report 27
CPU C6 Report 27
CSM 33–34
D
Data Cache Unit 24
Date 14
DDR Performance 30
76
Decoding
4G 21
Discard Changes and Exit
70
E
Energy Performance 26
Enhanced SpeedStep 26
Erase Disk 16
Erase SATA hard disk 16
Error Logging 28
Event Log 57, 62
Exit Menu 70
expansion card 20
External SATA Port 32
F
F12, function key 11
Finish
BIOS Setup 70
Forbidden Signature Database (DBX)
frequency 30
52
H
Hardware Prefetcher 23
Hot Plug 32
Hyper Threading 22
I
Independent Firmware Recovery 42
Intel Virtualization Technology 25
Interface baud rate 66
Interface settings 66
IPMI Management 60
iRMC 62–63
K
Key Exchange Key (KEK) 50–51
Key Management 49–52
L
LAN 12, 17–18
Launch CSM 33
Launch PXE OpROM Policy 34
Launch Storage OpROM Policy 34
Launch Video OpROM Policy 34
Legacy USB Support 36
Limit CPUID Maximum 23
Fujitsu
Index
M
Main Menu 13
Mass Storage Devices 37
Memory Configuration 30
Memory Error 28
N
Network Stack 42
Noise level 33
NUMA 30
NumLock 67
O
Onboard Device Configuration 17
Open source software license information
Operating system boot 63
Other PCI Device ROM Priority 34
Override OS Energy Performance 26
P
Package C State limit 27
Password 45
Administrator Password 45
Hard Disk Master Password 48
Hard Disk User Password 46, 48
User Password 45–46
User Password on Boot 46
PCI 20
ASPM Support 21
PCI parity errors 20
PCI system errors 20
Platform Key 50
Platform Key (PK) 50
Platform Mode 48
Power failure 62
Power failure, system reaction 54
Power Technology 25
Primary Display 68
R
Recovery Update
75
S
SATA Configuration 30
SATA Controller 30
SATA Port n 32
SATA ports 31
Save Changes and Exit 70
Secure Boot 48–49
Secure Boot Control 49
Fujitsu
13
Secure Boot Keys 50
Secure Boot Mode 49
Security Menu 44
Serial interface 40, 62
Server address 19
Setup,
see BIOS Setup 11
slots 20
speed 30
sSATA 31
Staggered Spin-up 32
Super IO Configuration 39
Switch on system
network 55
System Date / System Time
System Information 13
System Language 13
System power-on
LAN controller 55
14
T
Temperature monitoring 61
Terms of Use 18
Time 14
Time monitoring 63
Trusted Computing 35
Trusted Platform Module 35
Pending TPM operation 35
TPM State 35
TPM Status Information 35
TPM Support 35
Turbo Mode 26
U
Update 18–19, 73
USB 36, 38
USB keyboard 56
USB ports 37
V
VT-d
25
W
Wake Up Mode 56
Wake Up Timer 55
Write protection 46
X
xHCI Mode
36
77
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising