MI981 - ibase.com.tw

MI981 - ibase.com.tw
MI981
Intel® Q87 Based Mini-ITX board
Mini ITX Motherboard
USER’S MANUAL
Version 1.0
Acknowledgments
AMI is a registered trademark of American Megatrends Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel and Intel® 4th Generation Core DC/QC Processor are
registered trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Fintek is a registered trademark of Fintek Electronics Corporation.
All other product names or trademarks are properties of their
respective owners.
ii
MI981 User’s Manual
Table of Contents
Introduction ....................................................... 1
Product Description............................................................. 1
Checklist .............................................................................. 1
MI981 Specifications .......................................................... 2
Board Dimensions ............................................................... 4
Installations ....................................................... 5
Installing the Memory ......................................................... 6
Setting the Jumpers ............................................................. 7
Connectors on MI981 ........................................................ 12
BIOS Setup ....................................................... 25
Drivers Installation ...................................... 51
Intel Chipset Software Installation Utility ........................ 52
VGA Drivers Installation .................................................. 53
Realtek HD Audio Driver Installation .............................. 54
LAN Drivers Installation................................................... 55
Intel® Management Engine Interface ............................... 56
Intel® USB 3.0 Drivers ..................................................... 57
Appendix............................................................ 59
A. I/O Port Address Map .................................................. 59
B. Interrupt Request Lines (IRQ) ...................................... 60
C. Watchdog Timer Configuration ................................... 61
MI981 User’s Manual
iii
This page is intentionally left blank.
iv
MI981 User’s Manual
INTRODUCTION
Introduction
Product Description
The MI981 Mini ITX motherboard is based on the latest Intel® Q87
chipset. The platform supports Intel® 4th Generation Core™ DT i7/i5/i3
processors. The latest Intel® processors provide advanced performance
in both computing and graphics quality. This meets the requirement of
customers in the gaming, POS, digital signage and server market
segment.
The platform supports two SO-DIMM sockets that can accommodate up
to 16GB of DDR3-1600 Non ECC memory. The Intel® 4th Gen. Core™
DT processor integrated HD graphics supports 3 independent displays,
Direct X 11.1, OpenGL 3.2, and Open CL 1.2. Display interfaces are for
HDMI, DisplayPort and VGA CRT.
With two Gigabit Ethernets, the MI981 Mini ITX board utilizes the
dramatic increase in performance provided Intel’s latest cutting-edge
technology. Expansion is provided by PCIe(16x), one full sized
MiniPCIe and a half sized MiniPCIe. Onboard connectors support 4x
SATA III, 4x or 6x USB 2.0 depending on the MI981 model and 6x COM
ports. The board measures 170mm x 170mm.
Checklist
Your MI981 package should include the items listed below.
 The MI981 MINI ITX motherboard
 This User’s Manual
 1 CD containing chipset drivers and flash memory utility
MI981 User’s Manual
1
INTRODUCTION
MI981 Specifications
Model Name
Form Factor
CPU Type
CPU Speed
Cache Size
CPU Socket
Chipset
BIOS
Memory
VGA
LAN
USB
Serial ATA
Storage
Device
Audio
LPC I/O
Digital IO
IAMT 9.1
TPM 1.2
2
MI981AF
Mini ITX
- Haswell Refresh 4th Generation Intel® CoreTM i7/i5/i3/Pentium DT
processor & FCLGA1150 package [37.5 mm x 37.5mm]
- TDP: 35W ~ 84W
Up to 4.0GHz
Up to 8MB
LGA1150 (Socket H3)
Intel® Q87 PCH
Package =23 mm x 22 mm, 0.65 mm ball pitch
AMI BIOS
Haswell Refresh 4th Generation Intel® CoreTM DT processors integrated
memory controller,
DDR3-1600 MHz@1.5V
SO-DIMM x 2, Max. 16GB (Non-ECC)
Haswell Refresh 4th Generation Intel® DT processor integrated HD Gfx,
supports 3 independent displays, Direct X 11.1, OpenGL 3.2, Open CL
1.2
DVI-D x 1 (Thru port C, with level shifter ASM1442K)
DisplayPort x 1 (Thru port D)
LVDS (Thru port B, via NXP PTN3460)
VGA x 1 (Thru PCH)
1.
Intel® I217LM PHY GbE
2.
Intel® I211AT PCIe GbE as 2nd LAN
USB 2.0 host controller [Q87 Integrated], supports 8 ports
- 6 ports via onboard pin header
- 2 ports via MiniPCIe socket
USB 3.0 host controller [Q87 Integrated], supports 6 ports
- 6 ports via the rear panel I/O
Intel® Q87 PCH built-in SATA controller, supports 4x SATA 3.0 (6Gbps)
mSATA x 1 thru Mini-PCIe slot [full-sized]
Intel® Q87 PCH built-in High Definition Audio controller + Realtek ALC892
w/ 7.1 channels
Fintek F81866AD-I (128-pin LQFP [14mm x 14 mm])
COM #1 (RS232/422/485) support ring-in with power @500 mA
(selectable for 5V or 12V) [EXAR SP339EER1 232/422/485
transceiver x 1 for jumper-less]
COM #2 (RS232 only), support ring-in with power @500 mA
(selectable for 5V or 12V)
COM #3~COM #6 (RS232 only)
Hardware Monitor (2 thermal inputs,4 voltage monitor inputs & 2 Fan
headers)
CPU FAN x 1(PWN Fan type, 4-pin connector)
SYS fan x 1(PWM Fan type, 4-pin connector)]
4 in & 4 out
Intel® Active Management Technology ver. 9.1
Infineon SLB9655
MI981 User’s Manual
INTRODUCTION
Expansion
Slots
Edge
Connectors
Onboard
Header/Conn
ector
Watchdog
Timer
System
Voltage
Other
Environment
Board Size
Operation
System
- PCI-Express (16x) x1 [Gen 3.0 PEG]
- Mini PCI-Express x 2 port [1 x Full-sized,1 x Half-sized] , both support
USB 2.0 signal / supports mSATA thru full-size mini PCIe slot
Dual DB9 stack connector for COM #1 / #2
VGA + DVI-D stack connector x1
DisplayPort + dual USB (3.0) stack connector x1
RJ-45 + dual USB (3.0) stack connector x2
Triplet type Jack 3x1 for Audio port [Line-in / Line-out / Mic-in]
4 ports x SATA III [Blue color]
DF-11 2x4 header x 3 for 6 ports USB 2.0
DF-11 2x5 box header x 4 for COM2/3/4 (RS232 only)
DF-20 20-pin connector x 2 for Dual channel LVDS
1x4 box header for LCD backlight control
2x5 header for Digital IO
2x5 header for front Audio
2x4 header for front panel I/O (2.54 pitch)
2x2 pin ATX power connector x1
1x ATX standard 24-pin type for power connector
Yes (256 segments, 0, 1, 2…255 sec/min)
ATX standard 24-pins type
4 pin type (+12V only)
- LAN Wakeup
- iSMART 3.0
Operation Temperature: 0~60 degree C
Storage Temperature: -20~80 degree C
Relative humidity: 0~90%, non-condensing
170mm x 170mm
Windows 7, Windows 8, Linux
MI981 User’s Manual
3
INTRODUCTION
[
Board Dimensions
4
MI981 User’s Manual
INSTALLATIONS
Installations
This section provides information on how to use the jumpers and
connectors on the MI981 in order to set up a workable system. The topics
covered are:
Installing the Memory ............................................................................ 6
Setting the Jumpers ................................................................................ 7
Connectors on MI981 .......................................................................... 12
MI981 User’s Manual
5
INSTALLATIONS
Installing the Memory
The MI981 board supports two DDR3 memory modules for a maximum
total of 16GB in DDR3 SODIMM memory type.
Installing and Removing Memory Modules
To install the DDR3 modules, locate the memory slot on the board and
perform the following steps:
1. Hold the DDR3 module so that the key of the DDR3 module aligned
with that on the memory slot.
2. Gently push the DDR3 module in an upright position until the clips of
the slot close to hold the DDR3 module in place when the DDR3
module touches the bottom of the slot.
3. To remove the DDR3 module, press the clips with both hands.
Lock
DDR3 Module
Lock
6
Lock
Lock
MI981 User’s Manual
INSTALLATIONS
Setting the Jumpers
Jumpers are used on MI981 to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on MI981 and their respective functions.
Jumper Locations on MI981 .................................................................. 8
JP1: COM2 RS232 RI/+5V/+12V Power Setting .................................. 9
JP2: COM1 RS232 RI/+5V/+12V Power Setting .................................. 9
JP3: LVDS Panel Power Selection ...................................................... 10
JP4: Power Good Selection ................................................................. 10
JP5: Flash Descriptor Security Override (Factory use only) ................ 11
JBAT1: Clear CMOS Contents............................................................ 11
MI981 User’s Manual
7
INSTALLATIONS
Jumper Locations on MI981
Jumpers on MI981 ........................................................................... Page
JP1: COM2 RS232 RI/+5V/+12V Power Setting .................................. 9
JP2: COM1 RS232 RI/+5V/+12V Power Setting .................................. 9
JP3: LVDS Panel Power Selection ...................................................... 10
JP4: Power Good Selection .................................................................. 10
JP5: Flash Descriptor Security Override (Factory use only) ................ 11
JBAT1: Clear CMOS Contents ............................................................ 11
8
MI981 User’s Manual
INSTALLATIONS
JP1: COM2 RS232 RI/+5V/+12V Power Setting
JP1
Setting
Pin 1-3
Short/Closed
Pin 3-4
Short/Closed
Pin 3-5
Short/Closed
5
1
6
2
Function
+12V
RI
+5V
JP2: COM1 RS232 RI/+5V/+12V Power Setting
JP2
Setting
Pin 1-3
Short/Closed
Pin 3-4
Short/Closed
Pin 3-5
Short/Closed
5
1
6
2
Function
+12V
RI
+5V
MI981 User’s Manual
9
INSTALLATIONS
JP3: LVDS Panel Power Selection
1
3
JP3
Setting
Panel Voltage
Pin 1-2
Short/Closed
3.3V (default)
Pin 2-3
Short/Closed
5V
JP4: Power Good Selection
1
JP4
10
2
Function
Short
Factory use only
Open
Normal
MI981 User’s Manual
INSTALLATIONS
JP5: Flash Descriptor Security Override (Factory use only)
1
JP5
2
Flash Descriptor Security Override
Open
Disabled (Default)
Close
Enabled
JBAT1: Clear CMOS Contents
3
1
JBAT1
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS
MI981 User’s Manual
11
INSTALLATIONS
Connectors on MI981
Connector Locations on MI981 ........................................................... 13
CN1: COM1 and COM2 Serial Ports................................................... 14
CN2: VGA and DVI-D Connector ....................................................... 14
CN3: USB3.0 Connector ..................................................................... 15
CN4: DP Connector ............................................................................. 15
CN5: Gigabit LAN (Intel I217LM) / USB3.0 ...................................... 15
CN6, CN7, CN8, CN9: SATA Connectors .......................................... 15
CN10: Gigabit LAN (Intel I211AT) / USB3.0 .................................... 15
CN11: HD Audio Connector ................................................................ 15
J1: ATX 12V Power Connector ........................................................... 16
J4: ATX Power Supply Connector ....................................................... 16
J5, J6: LVDS Connectors ..................................................................... 17
J7: Digital I/O ...................................................................................... 17
J8: LCD Backlight Connector .............................................................. 18
J9: Mini PCIE/mSATA Connector ...................................................... 18
J10: Mini PCIE Connector ................................................................... 18
J11: SPI Flash Connector (Factory use only) ....................................... 19
J12: MCU Flash Connector (factory use only) ..................................... 19
J13: Debug 80 Port Connector (factory use only) ................................ 19
J14: Front Panel Function Connector ................................................... 20
J15, J16, J17, J18: COM3/COM4/COM5/COM6 Connector .............. 21
J19, J20, J21: USB Connectors ............................................................ 21
J22: Audio Front Header ...................................................................... 22
PCIE1: PCI-E X16 Slot ....................................................................... 22
CPU_FAN1: CPU Fan Power Connector ............................................ 23
SYS_FAN1: System Fan1 Power Connector ....................................... 23
12
MI981 User’s Manual
INSTALLATIONS
Connector Locations on MI981
MI981 User’s Manual
13
INSTALLATIONS
CN1: COM1 and COM2 Serial Ports
Pin #
Signal Name
RS-232
R2-422
RS-485
[
1
2
3
4
5
6
7
8
9
10
DCD
RX
TX
DTR
Ground
DSR
RTS
CTS
RI
NC
TXTX+
RX+
RXGround
NC
NC
NC
NC
NC
CN2: VGA and DVI-D Connector
Signal Name Pin #
Red
1
Blue
3
GND
5
GND
7
N.C.
9
N.C.
11
VGA
HSYNC
13
DDCCLK
15
14
DATADATA+
NC
NC
Ground
NC
NC
NC
NC
NC
Pin #
2
4
6
8
10
12
14
MI981 User’s Manual
Signal Name
Green
N.C.
GND
GND
GND
DDCDATA
VSYNC
INSTALLATIONS
[
Signal Name
Pin #
Pin #
Signal Name
DATA 2DATA 2+
GROUND
N.C.
N.C.
DDC CLOCK
DDC DATA
N.C
DATA 1DATA 1+
GROUND
N.C.
N.C.
DDC POWER
GROUND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
HOT POWER
DATA 0DATA 0+
GROUND
N.C.
N.C.
GROUND
CLOCK +
CLOCK -
CN3: USB3.0 Connector
CN4: DP Connector
CN5: Gigabit LAN (Intel I217LM) / USB3.0
CN6, CN7, CN8, CN9: SATA Connectors
CN10: Gigabit LAN (Intel I211AT) / USB3.0
CN11: HD Audio Connector
MI981 User’s Manual
15
INSTALLATIONS
J1: ATX 12V Power Connector
Pin #
1
2
3
4
3
1
4
2
Signal Name
Ground
Ground
+12V
+12V
J4: ATX Power Supply Connector
Signal Name
3.3V
-12V
Ground
PS-ON
Ground
Ground
Ground
-5V
+5V
+5V
+5V
Ground
16
Pin #
13
14
15
16
17
18
19
20
21
22
23
24
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
24
13
12
1
Signal Name
3.3V
3.3V
Ground
+5V
Ground
+5V
Ground
Power good
5VSB
+12V
+12V
+3.3V
MI981 User’s Manual
INSTALLATIONS
J5, J6: LVDS Connectors
Signal Name
LCD_PWR
LD3+
GND
CLK+
GND
LD2+
GND
LD1+
GND
LD0+
Pin #
19
17
15
13
11
9
7
5
3
1
Pin #
20
18
16
14
12
10
8
6
4
2
19
20
1
2
Signal Name
LCD_PWR
LD3GND
CLKGND
LD2GND
LD1GND
LD0-
J7: Digital I/O
Signal Name
GND
OUT3
OUT2
IN3
IN2
Pin
1
3
5
7
9
1
2
9
10
Pin
2
4
6
8
10
Signal Name
VCC
OUT1
OUT0
IN1
IN0
MI981 User’s Manual
17
INSTALLATIONS
J8: LCD Backlight Connector
1
4
2
Pin #
1
2
3
4
Signal Name
Backlight Power
Backlight Enable
Brightness Control
Ground
J9: Mini PCIE/mSATA Connector
J10: Mini PCIE Connector
18
MI981 User’s Manual
INSTALLATIONS
J11: SPI Flash Connector (Factory use only)
2
10
1
9
J12: MCU Flash Connector (factory use only)
1
4
J13: Debug 80 Port Connector (factory use only)
1
2
9
10
MI981 User’s Manual
19
INSTALLATIONS
J14: Front Panel Function Connector
7
1
8
2
ATX Power ON Switch: Pins 1 and 2
This 2-pin connector is an “ATX Power Supply On/Off Switch” on the
system that connects to the power switch on the case. When pressed, the
power switch will force the system to power on. When pressed again, it
will force the system to power off.
Hard Disk Drive LED Connector: Pins 3 and 4
This connector connects to the hard drive activity LED on control panel.
This LED will flash when the HDD is being accessed.
Pin #
4
3
Signal Name
HDD Active
3.3V
Reset Switch: Pins 5 and 6
The reset switch allows the user to reset the system without turning the
main power switch off and then on again. Orientation is not required
when making a connection to this header.
Power LED: Pins 7 and 8
Pin #
7
8
20
Signal Name
+5V
GND
MI981 User’s Manual
INSTALLATIONS
J15, J16, J17, J18: COM3/COM4/COM5/COM6 Connector
Signal Name
DCD, Data carrier detect
TXD, Transmit data
GND, ground
RTS, Request to send
RI, Ring indicator
Pin #
1
3
5
7
9
2
1
10
9
Pin #
2
4
6
8
10
Signal Name
RXD, Receive data
DTR, Data terminal ready
DSR, Data set ready
CTS, Clear to send
Not Used
J19, J20, J21: USB Connectors
Signal Name
VCC
D0D0+
GND
Pin
1
3
5
7
Pin
2
4
6
8
2
1
8
7
Signal Name
GND
D1+
D1VCC
MI981 User’s Manual
21
INSTALLATIONS
J22: Audio Front Header
Signal Name
MIC2_L
MIC2_R
Line2_R
Sense
Line2_L
1
2
9
10
Pin #
1
3
5
7
9
Pin #
2
4
6
8
10
PCIE1: PCI-E X16 Slot
22
MI981 User’s Manual
Signal Name
Ground
Presence#
MIC2_ID
NC
Line2_ID
INSTALLATIONS
CPU_FAN1: CPU Fan Power Connector
1
4
Pin #
1
2
3
4
Signal Name
Ground
+12V
Rotation detection
Control
SYS_FAN1: System Fan1 Power Connector
4
Pin #
1
2
3
4
1
Signal Name
Ground
+12V
Rotation detection
Control
MI981 User’s Manual
23
INSTALLATIONS
This page is intentionally left blank.
24
MI981 User’s Manual
BIOS SETUP
BIOS Setup
This chapter describes the different settings available in the AMI BIOS
that comes with the board. The topics covered in this chapter are as
follows:
BIOS Introduction ............................................................................... 26
BIOS Setup .......................................................................................... 26
Advanced Settings ............................................................................... 27
Chipset Settings ................................................................................... 42
Boot Settings........................................................................................ 47
CSM parameters .................................................................................. 48
Security Settings .................................................................................. 49
Save & Exit Settings ............................................................................ 50
MI981 User’s Manual
25
BIOS SETUP
BIOS Introduction
The BIOS (Basic Input/Output System) installed in your computer
system’s ROM supports Intel processors. The BIOS provides critical
low-level support for a standard device such as disk drives, serial ports
and parallel ports. It also has password protection as well as special
support for detailed fine-tuning of the chipset controlling the entire
system.
BIOS Setup
The BIOS provides a Setup utility program for specifying the system
configurations and settings. The BIOS ROM of the system stores the
Setup utility. When you turn on the computer, the BIOS is immediately
activated. Pressing the <Del> key immediately allows you to enter the
Setup utility. If you are a little bit late pressing the <Del> key, POST
(Power On Self Test) will continue with its test routines, thus preventing
you from invoking the Setup. If you still wish to enter Setup, restart the
system by pressing the ”Reset” button or simultaneously pressing the
<Ctrl>, <Alt> and <Delete> keys. You can also restart by turning the
system Off and back On again. The following message will appear on the
screen:
Press
<DEL>
to
Enter
Setup
In general, you press the arrow keys to highlight items, <Enter> to select,
the <PgUp> and <PgDn> keys to change entries, <F1> for help and
<Esc> to quit.
When you enter the Setup utility, the Main Menu screen will appear on
the screen. The Main Menu allows you to select from various setup
functions and exit choices.
Warning: It is strongly recommended that you avoid making any
changes to the chipset defaults. These defaults have been
carefully chosen by both AMI and your system manufacturer
to provide the absolute maximum performance and
reliability. Changing the defaults could cause the system to
become unstable and crash in some cases.
26
MI981 User’s Manual
BIOS SETUP
Main Settings
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
System Language
[English]
System Date
System Time
[Tue 01/20/2009]
21:25:55
Access Level
Administrator
Security
Save & Exit
Choose the system default
language
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
System Language
Choose the system default language.
System Date
Set the Date. Use Tab to switch between Date elements.
System Time
Set the Time. Use Tab to switch between Time elements.
Advanced Settings
This section allows you to configure and improve your system and allows
you to set up some system features according to your preference.
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
► PCI Subsystem Settings
► ACPI Settings
► Trusted Computing
► Wake up event Configuration
► CPU Configuration
► SATA Configuration
► Shutdown Temperature Configuration
► LVDS (eDP/DP) Configuration
► iSmart Controller 3.1
► AMT Configuration
► USB Configuration
► F81866 Super IO Configuration
► F81866 H/W Monitor
MI981 User’s Manual
Save & Exit
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
27
BIOS SETUP
PCI Subsystem Settings
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
PCI Bus Driver Version
PCI Common Settings
PCI Latency Timer
VGA Palette Snoop
PERR# Generation
SERR# Generation
► PCI Express Settings
Chipset
Boot
Security
Save & Exit
V 2.05.02
→ ← Select
32 PCI Bus Clocks
Disabled
Disabled
Disabled
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
PCI Latency Timer
Value to be programmed into PCI Latency Timer Register.
VGA Palette Snoop
Enables or disables VGA Palette Registers Snooping.
PERR# Generation
Enables or disables PCI device to generate PERR#.
SERR# Generation
Enables or disables PCI device to generate SERR#.
PCI Express Settings
Change PCI Express devices settings.
28
MI981 User’s Manual
Screen
BIOS SETUP
PCI Express Settings
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
PCI Express Device Register Settings
Relaxed Ordering
Extended Tag
No Snoop
Maximum Payload
Maximum Read Request
Disabled
Disabled
Enabled
Auto
Auto
PCI Express Link Register Settings
ASPM Support
WARNING: Enabling ASPM may cause
some PCI-E devices to fail
Extended Synch
Link Training Retry
Link Training Timeout (uS)
Unpopulated Links
Restore PCIE Registers
Disabled
→ ← Select
Disabled
5
100
Keep Link ON
Disabled
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Relaxed Ordering
Enables or disables PCI Express Device Relaxed Ordering.
Extended Tag
If ENABLED allows device to use 8-bit Tag field as a requester.
No Snoop
Enables or disables PCI Express Device No Snoop option.
Maximum Payload
Set Maximum Payload of PCI Express Device or allow System BIOS to
select the value.
Maximum Read Request
Set Maximum Read Request Size of PCI Express Device or allow System
BIOS to select the value.
ASPM Support
Set the ASPM Level: Force L0s – Force all links to L0s State:
AUTO – BIOS auto configure: DISABLE – Disables ASPM.
Extended Synch
If ENABLED allows generation of Extended Synchronization patterns.
MI981 User’s Manual
29
BIOS SETUP
Link Training Retry
Defines number of Retry Attempts software will take to retrain the link if
previous training attempt was unsuccessful.
Link Training Timeout (uS)
Defines number of Microseconds software will wait before polling ‘Link
Training’ bit in Link Status register. Value range from 10 to 1000 uS.
Unpopulated Links
In order to save power, software will disable unpopulated PCI Express
links, if this option set to ‘Disable Link’.
Restore PCIE Registers
On non-PCI Express aware OS’s (Pre Windows Vista) some devices may
not be correctly reinitialized after S3.Enabling this restore PCI Express
device configuration on S3 resume
Warning: Enabling this may cause issues with other hardware after S3
resume.
30
MI981 User’s Manual
BIOS SETUP
ACPI Settings
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
ACPI Settings
→ ← Select
Enable Hibernation
ACPI Sleep State
Lock Legacy Resources
S3 Video Repost
Enabled
S3 (Suspend to R…)
Disabled
Disabled
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Enable Hibernation
Enables or Disables System ability to Hibernate (OS/S4 Sleep State).
This option may be not effective with some OS.
ACPI Sleep State
Select ACPI sleep state the system will enter, when the SUSPEND button
is pressed.
Lock Legacy Resources
Enabled or Disabled Lock of Legacy Resources.
S3 Video Repost
Enable or disable S3 Video Repost.
MI981 User’s Manual
31
BIOS SETUP
Trusted Computing
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Configuration
Security Device Support
Chipset
Boot
Security
Save & Exit
Disabled
→ ← Select
Current Status Information
SUPPORT TURNED OFF
Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Security Device Support
This configuration is supported only with MI981AF. Enables or disables
BIOS support for security device. O.S. will not show Security Device.
TCG EFI protocol and INT1A interface will not be available.
TPM State
Enable/Disable Security Device. NOTE: Your Computer will reboot
during restart in order to change State of the Device.
Pending operation
Schedule an Operation for the Security Device. NOTE: Your Computer
will reboot during restart in order to change State of Security Device.
32
MI981 User’s Manual
BIOS SETUP
Wake up event settings
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Chipset
Wake on Ring
Wake on PCIE Wake Event
Boot
Security
Disabled
Disabled
Save & Exit
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Wake up by Ring / Wake up by PCIE WAKE#
The options are Disabled and Enabled.
MI981 User’s Manual
33
BIOS SETUP
CPU Configuration
This section shows the CPU configuration parameters.
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
Save & Exit
CPU Configuration
Intel(R) CPU Core(TM)i3-4340TE @ 2.60GHz
CPU Signature
306c3
Processor Family
6
Microcode Patch
17
FSB Speed
100MHz
Max CPU Speed
Min CPU Speed
2600 MHz
800 MHz
CPU Speed
Processor Cores
Intel HT Technology
Intel VT-x Technology
Intel SMX Technology
64-bit
EIST
2600 MHz
2
Supported
Supported
Supported
Supported
Supported
→ ← Select
Enabled
All
Enabled
Enabled
Turbo performance
Enabled
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Hyper-threading
Active Processor Cores
Execute Disable Bit
Intel Virtualization Technology
Boot performance mode
EIST
Screen
Active Processor Cores
Number of cores to enable in each processor package.
Execute Disable Bit
XD can prevent certain classes of malicious buffer overflow attacks when
combined with a supporting OS
Intel Virtualization Technology
When enabled, a VMM can utilize the additional hardware capabilities
provided by Vanderpool Technology.
Boot Performance Mode
Select the performance state that the BIOS will set before OS handoff.
EIST
Enabled/Disabled Intel Speedstep.
34
MI981 User’s Manual
BIOS SETUP
SATA Configuration
SATA Devices Configuration.
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
SATA Controller(s)
SATA Mode Selection
SATA Controller Speed
Enabled
AHCI
Default
SATA Port0
Software Preserve
Hot Plug
SATA Port1
Software Preserve
Empty
Unknown
Dissabled
Empty
Unknown
Hot Plug
SATA Port2
Software Preserve
Hot Plug
SATA Port3
Software Preserve
Hot Plug
SATA Port4
Software Preserve
Hot Plug
SATA Port5
Software Preserve
Hot Plug
Dissabled
Empty
Unknown
Dissabled
Empty
Unknown
Dissabled
Empty
Unknown
Dissabled
Empty
Unknown
Dissabled
Security
Save & Exit
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
SATA Controller(s)
Enable or disable SATA Device.
SATA Mode Selection
Determines how SATA controller(s) operate.
(1) IDE Mode.
(2) AHCI Mode.
(3) RAID Mode. (MI981AF only)
SATA Controller Speed
Indicates the maximum speed the SATA controller can support.
Hot Plug
Designates this port as Hot Pluggable.
MI981 User’s Manual
35
BIOS SETUP
Shutdown Temperature Configuration
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Chipset
APCI Shutdown Temperature
Boot
Security
Save & Exit
→ ← Select
Disabled
Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save ESC: Exit
ACPI Shutdown Temperature
The default setting is Disabled.
LVDS (eDP/DP) Configuration
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
Save & Exit
LVDS (eDP/DP) Configuration
→ ← Select
DP/eDP LVDS Control
Disable
DP/eDP LVDS Control
The default setting is Disabled.
36
MI981 User’s Manual
Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save ESC: Exit
BIOS SETUP
iSmart Controller 3.1
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
Save & Exit
→ ← Select
iSmart Controller 3.1
Power-On after Power failure
Temperature Guardian
Disable
Disable
Schedule Slot 1
Schedule Slot 2
None
None
Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Power-On after Power failure
This field sets the system power status whether Disable or Enable when
power returns to the system from a power failure situation.
Temperature Guardian
Generate the reset signal when system hangs up on POST
Schedule Slot 1 / 2
Setup the hour/minute for system power on.
MI981 User’s Manual
37
BIOS SETUP
AMT Configuration
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Chipset
Intel AMT
BIOS Hotkey Pressed
MEBx Selection Screen
Hide Un-Configure ME Confirmation
Un-Configure ME
Amt Wait Timer
Activate Remote Assistance Process
USB Configure
PET Progress
AMT CIRA Timeout
Watchdog
OS Timer
BIOS Timer
Boot
Security
Enabled
Disabled
Disabled
Disabled
Disabled
0
Disabled
Enabled
Enabled
0
Disabled
0
0
Save & Exit
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
[
AMT configuration is supported only with MI981AF (with iAMT
function).
Intel AMT
Enable/Disable Intel (R) Active Management Technology BIOS
Extension.
Note: iAMT H/W is always enabled. This option just controls the BIOS
extension execution. If enabled, this requires additional firmware in the
SPI device.
BIOS Hotkey Pressed
OEMFLag Bit 1: Enable/Disable BIOS hotkey press.
AMT Configuration
OEMFLag Bit 2: Enable/Disable MEBx selection screen.
Hide Un-Configure ME Configuration
OEMFLag Bit 6: Hide Un-Configure ME without password
Confirmation Prompt.
Un-Configure ME
OEMFLag Bit 15: Un-Configure ME without password.
Amt Wait Timer
Set timer to wait before sending ASF_GET_BOOT_OPTIONS.
Activate Remote Assistance Process
Trigger CIRA boot.
38
MI981 User’s Manual
BIOS SETUP
USB Configure
Enable/Disable USB Configure function.
PET Progress
User can Enable/Disable PET Events progress to receive PET.
Watchdog Timer
Enable/Disable Watchdog Timer.
USB Configuration
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
Save & Exit
USB Configuration
USB Module Version
8.10.28
USB Devices:
2 Keyboards, 1 Mouse, 2 Hubs
Legacy USB Support
USB3.0 Support
XHCI Hand-off
EHCI Hand-off
USB Mass Storage Driver Support
Enabled
Enabled
Enabled
Enabled
Enabled
USB hardware delays and time-outs:
USB Transfer time-out
Device reset tine-out
Device power-up delay
20 sec
20 sec
Auto
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Legacy USB Support
Enables Legacy USB support.
AUTO option disables legacy support if no USB devices are connected.
DISABLE option will keep USB devices available only for EFI
applications.
USB3.0 Support
Enable/Disable USB3.0 (XHCI) Controller support.
XHCI Hand-off
This is a workaround for OSes without XHCI hand-off support. The
XHCI ownership change should be claimed by XHCI driver.
MI981 User’s Manual
39
BIOS SETUP
EHCI Hand-off
This is a workaround for OSes without EHCI hand-off support. The
XHCI ownership change should be claimed by EHCI driver.
USB Mass Storage Driver Support
Enable/Disable USB Mass Storage Driver Support.
USB Transfer time-out
The time-out value for Control, Bulk, and Interrupt transfers.
Device reset tine-out
USB mass Storage device start Unit command time-out.
Device power-up delay
Maximum time the device will take before it properly reports itself to the
Host Controller. ‘Auto’ uses default value: for a Root port it is 100ms, for
a Hub port the delay is taken from Hub descriptor.
F81866 Super IO Configuration
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
Super IO Configuration
F81866 Super IO Chip
F81866
→ ← Select
► Serial Port 1 Configuration
► Serial Port 2 Configuration
► Serial Port 3 Configuration
► Serial Port 4 Configuration
► Serial Port 5 Configuration
► Serial Port 6 Configuration
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Serial Port Configuration
Set Parameters of Serial Ports. User can Enable/Disable the serial port
and Select an optimal settings for the Super IO Device.
40
MI981 User’s Manual
BIOS SETUP
F81866 H/W Monitor
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
Save & Exit
PC Health Status
CPU temperature
System temperature
CPU Fan Speed
System Fan Speed
Vcore
+5V
+12V
+1.5V
+3.3V
CPU smart fan control
+33.0 C
+34.5 C
4066 RPM
N/A
+1.704 V
+5.144 V
+12.096V
+1.512V
+3.424
Disabled
System smart fan control
Disabled
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
CPU/System smart fan control
This field enables or disables the smart fan feature.
Disabled (default)
50 ℃
60 ℃
70 ℃
80 ℃
90 ℃
Temperatures/Voltages
These fields are the parameters of the hardware monitoring function
feature of the motherboard. The values are read-only values as monitored
by the system and show the PC health status.
MI981 User’s Manual
41
BIOS SETUP
Chipset Settings
This section allows you to configure and improve your system and allows
you to set up some system features according to your preference.
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
Save & Exit
→ ←
► PCH-IO Configuration
Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
► System Agent (SA) Configuration
PCH-IO Configuration
This section allows you to configure the North Bridge Chipset.
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Chipset
Intel PCH RC Version
Intel PCH SKU Name
Intel PCH Rev ID
Boot
Security
1.8.0.0
Q87
05/C2
► PCI Express Configuration
► USB Configuration
► PCH Azalia Configuration
PCH LAN Controller
Wake on LAN
SLP_S4 Assertion Width
Enabled
Enabled
4-5 Seconds
Save & Exit
→ ←
Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
PCH LAN Controller
Enable or disable onboard NIC.
Wake on LAN
Enable or disable integrated LAN to wake the system. (The Wake On
LAN cannot be disabled if ME is on at Sx state.)
SLP_S4 Assertion Width
Select a minimum assertion width of the SLP_S4# signal.
42
MI981 User’s Manual
BIOS SETUP
PCI Express Configuration
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
Save & Exit
PCI Express Configuration
DMI Link ASPM Control
DMI Link Extended Synch Control
PCIe-USB Glitch W/A
Subtractive Decode
Disabled
Disabled
Disabled
Disabled
► PCI Express Root Port 1
► PCI Express Root Port 2
► PCI Express Root Port 3
► PCI Express Root Port 4
► PCI Express Root Port 5
PCI-E Port 6 is assigned to LAN
► PCI Express Root Port 7
► PCI Express Root Port 8
→ ←
Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
DMI Link ASPM Control
The control of Active State Power Management on both NB side and SB
side of the DMI Link.
DMI Link Extended Synch Control
The control of Extended Synch on SB side of the DMI Link.
PCIe-USB Glitch W/A
PCIe-USB Glitch W/A for bad USB device(s) connected behind
PCIE/PEG port.
Subtractive Decode
Enable or disable PCI Express Subtractive Decode.
MI981 User’s Manual
43
BIOS SETUP
USB Configuration
Main
Advanced
Chipset
Boot
Security
Save & Exit
USB Configuration
USB Precondition
xHCI Mode
Disabled
Auto
USB Ports Per-Port Disable Control
Disabled
→ ←
Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
USB Precondition
Precondition work on USB host controller and root ports for faster
enumeration.
PCH Azalia Configuration
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
Save & Exit
PCH Azalia Configuration
→ ←
Azalia
Auto
Select Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Azalia
Control Detection of the Azalia device.
Disabled = Azalia will be unconditionally disabled.
Enabled Azalia will be unconditionally Enabled.
Auto = Azalia will be enabled if present, disabled otherwise.
44
MI981 User’s Manual
BIOS SETUP
System Agent (SA) Configuration
Aptio Setup Utility
Main
Advanced
Chipset
Boot
System Agent Bridge Name
System Agent RC Version
VT-d Capability
Haswell
1.8.0.0
Unsupported
CHAP Device (B0:D7:F0)
Thermal Device (B0:D4:F0)
CPU SA Audio Device (B0:D3:F0)
Enable NB CRID
Disabled
Disabled
Enabled
Disabled
Security
Save & Exit
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
► Graphics Configuration
► Memory Configuration
VT-d
Check to enable VT-d function on MCH.
Enable NB CRID
Enable or disable NB CRID WorkAround.
Graphics Configuration
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Graphics Configuration
IGFX VBIOS Version
IGfx Frequency
Primary Display
Primary PEG
Primary PCIE
Internal Graphics
Aperture Size
DVMT Pre-Allocated
DVMT Total Gfx Mem
Chipset
Boot
Security
Save & Exit
2179
700 MHz
→ ← Select
Auto
Auto
Auto
Auto
256MB
32M
256MB
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Screen
Primary Display
Select which of IGFX/PEG/PCI graphics device should be Primary
Display or select SG for switchable Gfx.
Primary PEG
Select PEG0/PEG1/PEG2/PEG3 Graphics device should be Primary
PEG.
MI981 User’s Manual
45
BIOS SETUP
Primary PCIE
Select PCIE0/PCIE1/PCIE2/PCIE3/PCIE4/PCIE5/PCIE6PCIE7
Graphics device should be Primary PCIE.
Internal Graphics
Keep IGD enabled based on the setup options.
Aperture Size
Select the Aperture Size.
DVMT Pre-Allocated
Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory Size used by
the Internal Graphics Device.
DVMT Total Gfx Mem
Select DVMT 5.0 Total Graphics Memory Size used by the Internal
Graphics Device.
Memory Configuration
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
Memory Information
Memory Frequency
Total Memory
DIMM#0
DIMM#1
DIMM#2
DIMM#3
CAS Latency (tCL)
Minimum delay time
CAS to RAS (tRCDmin)
Row Precharge (tRPmin)
Active to Precharge (tRASmin)
46
1333 MHz
4096 MB (DDR3)
2048 MB (DDR3)
Not Present
2048 MB (DDR3)
Not Present
11
11
11
28
MI981 User’s Manual
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
BIOS SETUP
Boot Settings
This section allows you to configure the boot settings.
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Boot Configuration
Setup Prompt Timeout
Bootup NumLock State
1
On
Quiet Boot
Fast Boot
Disabled
Disabled
Boot mode Select
LEGACY
Security
Save & Exit
FIXED BOOT ORDER Priorities
Boot Option #1
Boot Option #2
Boot Option #3
Boot Option #4
Boot Option #5
Boot Option #6
Boot Option #7
Hard Disk
CD/DVD
USB Hard Disk
USB CD/DVD
USB Key
USB Floppy
Network
► CSM16 Parameters
CSM Parameters
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Setup Prompt Timeout
Number of seconds to wait for setup activation key.
65535(0xFFFF) means indefinite waiting.
Bootup NumLock State
Select the keyboard NumLock state.
Quiet Boot
Enables/Disables Quiet Boot option.
Fast Boot
Enables/Disables boot with initialization of a minimal set of devices
required to launch active boot option. Has no effect for BBS boot
options.
FIXED BOOT ORDER Priorities
Sets the system boot order.
MI981 User’s Manual
47
BIOS SETUP
CSM parameters
This section allows you to configure the boot settings.
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
Launch CSM
Boot option filter
Launch PXE OpROM policy
Launch Storage OpROM policy
Launch Video OpROM policy
Enabled
UEFI and Legacy
Do not launch
Legacy only
Legacy only
Other PCI device ROM priority
Legacy OpROM
Save & Exit
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
Launch CSM
This option controls if CSM will be launched.
Boot option filter
This option controls what devices system can boot to.
Launch PXE OpROM policy
Controls the execution of UEFI and Legacy PXE OpROM.
Launch Storatge OpROM policy
Controls the execution of UEFI and Legacy Storage OpROM.
Launch Video OpROM policy
Controls the execution of UEFI and Legacy Video OpROM.
Other PCI device ROM priority
For PCI devices other than Network, Mass storage or Video defines
which OpROM to launch.
48
MI981 User’s Manual
BIOS SETUP
Security Settings
This section allows you to configure and improve your system and allows
you to set up some system features according to your preference.
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
Password Description
If ONLY the Administrator’s password is set, then
this only limit access to Setup and is only asked
for when entering Setup.
If ONLY the User’s password is set, then this is a
power on password and must be entered to boot
or enter Setup. In Setup the User will have
Administrator rights
The password length must be
in the following range:
Minimum length
Maximum length
→ ← Select
3
20
Administrator Password
User Password
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Administrator Password
Set Setup Administrator Password.
User Password
Set User Password.
MI981 User’s Manual
49
BIOS SETUP
Save & Exit Settings
Aptio Setup Utility – Copyright © 2012 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
Save Changes and Exit
Discard Changes and Exit
Save Changes and Reset
Discard Changes and Reset
Save & Exit
→ ← Select
Save Options
Save Changes
Discard Changes
Restore Defaults
Save as User Defaults
Restore User Defaults
Save Changes and Exit
Exit system setup after saving the changes.
Discard Changes and Exit
Exit system setup without saving any changes.
Save Changes and Reset
Reset the system after saving the changes.
Discard Changes and Reset
Reset system setup without saving any changes.
Save Changes
Save Changes done so far to any of the setup options.
Discard Changes
Discard Changes done so far to any of the setup options.
Restore Defaults
Restore/Load Defaults values for all the setup options.
Save as User Defaults
Save the changes done so far as User Defaults.
Restore User Defaults
Restore the User Defaults to all the setup options.
50
Screen
↑↓ Select Item
Enter: Select
+- Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit
MI981 User’s Manual
DRIVERS INSTALLATION
Drivers Installation
This section describes the installation procedures for software and
drivers. The software and drivers are included with the motherboard. If
you find the items missing, please contact the vendor where you made the
purchase. The contents of this section include the following:
Intel Chipset Software Installation Utility ........................................... 52
VGA Drivers Installation ..................................................................... 53
Realtek HD Audio Driver Installation ................................................. 54
LAN Drivers Installation ..................................................................... 55
Intel® Management Engine Interface .................................................. 56
Intel® USB 3.0 Drivers ....................................................................... 57
IMPORTANT NOTE:
After installing your Windows operating system, you must install first the
Intel Chipset Software Installation Utility before proceeding with the
drivers installation.
MI981 User’s Manual
51
DRIVER INSTALLATION
Intel Chipset Software Installation Utility
The Intel Chipset Drivers should be installed first before the software
drivers to enable Plug & Play INF support for Intel chipset components.
Follow the instructions below to complete the installation.
1. Insert the DVD that comes with the board. Click Intel and then
Intel(R) 8 Series Chipset Drivers.
2. Click Intel(R) Chipset Software Installation Utility.
3. When the Welcome screen to the Intel® Chipset Device Software
appears, click Next to continue.
4. Click Yes to accept the software license agreement and proceed with
the installation process.
5. On the Readme File Information screen, click Next to continue the
installation.
6. The Setup process is now complete. Click Finish to restart the
computer and for changes to take effect.
52
MI981 User’s Manual
DRIVERS INSTALLATION
VGA Drivers Installation
1. Insert the DVD that comes with the board. Click Intel and then
Intel(R) 8 Series Chipset Drivers. Click Intel(R) Graphics Driver.
2. When the Welcome screen appears, click Next to continue.
3. Click Yes to to agree with the license agreement and continue the
installation.
4. On the Readme File Information screen, click Next to continue the
installation of the Intel® HD Graphics Driver.
5. On the screen shown below, click Install to continue.
6. On the Setup Progress screen, click Next to continue.
7. Setup complete. Click Finish to restart the computer and for changes
to take effect.
MI981 User’s Manual
53
DRIVER INSTALLATION
Realtek HD Audio Driver Installation
1. Insert the DVD that comes with the board. Click Intel and then
Intel(R) 8 Series Chipset Drivers. Click Realtek High Definition Audio
Driver.
2. On the Welcome to the InstallShield Wizard screen, click Next to
proceed with and complete the installation process.
3. The InstallShield Wizard Complete. Click Finish to restart the
computer and for changes to take effect.
54
MI981 User’s Manual
DRIVERS INSTALLATION
LAN Drivers Installation
1. Insert the DVD that comes with the board. Click Intel and then
Intel(R) 8 Series Chipset Drivers. Click Intel(R) PRO LAN Network
Drivers.
2. Click Install Drivers and Software.
4. When the Welcome screen appears, click Next.
5. Click Next to to agree with the license agreement.
6. Click the checkbox for Drivers in the Setup Options screen to select it
and click Next to continue.
7. The wizard is ready to begin installation. Click Install to begin the
installation.
8. When InstallShield Wizard is complete, click Finish.
MI981 User’s Manual
55
DRIVER INSTALLATION
Intel® Management Engine Interface
Follow the steps below to install the Intel Management Engine.
1. Insert the DVD that comes with the board. Click Intel and then
Intel(R) 8 Series Chipset Drivers and then Intel(R) ME 9.0 Drivers.
2. When the Welcome screen to the InstallShield Wizard for Intel®
Management Engine Components, click the checkbox for Install Intel®
Control Center & click Next.
3. Click Yes to to agree with the license agreement.
4. When the Setup Progress screen appears, click Next. Then, click
Finish when the setup progress has been successfully installed.
56
MI981 User’s Manual
DRIVERS INSTALLATION
Intel® USB 3.0 Drivers
1. Insert the DVD that comes with the board. Click Intel and then
Intel(R) 8 Series Chipset Drivers. Click Intel(R) USB 3.0 Drivers.
2. When the Welcome screen to the InstallShield Wizard for Intel® USB
3.0 eXtensible Host Controller Driver, click Next.
3. Click Yes to to agree with the license agreement and continue the
installation.
4. On the Readme File Information screen, click Next to continue the
installation of the Intel® USB 3.0 eXtensible Host Controller Driver.
5. When the Setup Progress screen appears, click Next. Setup complete.
Click Finish to restart the computer and for changes to take effect.
MI981 User’s Manual
57
DRIVER INSTALLATION
This page is intentionally set blank.
58
MI981 User’s Manual
APPENDIX
Appendix
A. I/O Port Address Map
Each peripheral device in the system is assigned a set of I/O port
addresses which also becomes the identity of the device. The following
table lists the I/O port addresses used.
Address
0000h-001Fh
0000h-001Fh
0040h-0043h
0050h-0053h
0070h-0077h
0081h-0091h
0093h-009Fh
00C0h-00DFh
00F0h-00F0h
02E0h-02E7h
02E8h-02EFh
02F0h-02F7h
02F8h-02FFh
03B0h-03BBh
03C0h-03DFh
03E8h-03EFh
03F8h-03FFh
0D00h-FFFFh
E000h-EFFFh
F000h-F03Fh
F040h-F05Fh
F060h-F07Fh
F0A0h-F0A3h
F0B0h-F0B7h
F0C0h-F0C3h
F0D0h-F0D7h
F0E0h-F0E7h
Device Description
Direct memory access controller
PCI bus
System timer
System timer
System CMOS/real time clock
Direct memory access controller
Direct memory access controller
Direct memory access controller
Numeric data processor
Communications Port (COM6)
Communications Port (COM4)
Communications Port (COM5)
Communications Port (COM2)
Intel(R) HD Graphics 4600
Intel(R) HD Graphics 4600
Communications Port (COM3)
Communications Port (COM1)
PCI bus
Intel(R) 8 Series/C220 Series PCI Express Root Port #7
- 8C1C
Intel(R) HD Graphics 4600
Intel(R) 8 Series/C220 Series SMBus Controller - 8C22
Intel(R) 8 Series/C220 Series SATA AHCI Controller 8C02
Intel(R) 8 Series/C220 Series SATA AHCI Controller 8C02
Intel(R) 8 Series/C220 Series SATA AHCI Controller 8C02
Intel(R) 8 Series/C220 Series SATA AHCI Controller 8C02
Intel(R) 8 Series/C220 Series SATA AHCI Controller 8C02
Intel(R) Active Management Technology - SOL
(COM7)
MI981 User’s Manual
59
APPENDIX
B. Interrupt Request Lines (IRQ)
Peripheral devices use interrupt request lines to notify CPU for the
service required. The following table shows the IRQ used by the devices
on board.
Level
IRQ0
IRQ3
IRQ4
IRQ5
IRQ5
IRQ7
IRQ7
IRQ8
IRQ 10
IRQ 13
IRQ 16
IRQ 16
IRQ 16
IRQ 16
IRQ 16
IRQ 19
IRQ 19
IRQ 22
IRQ 23
60
Function
System Timer
Serial Port #2
Serial Port #1
Serial Port #3
Serial Port #4
Serial Port #5
Serial Port #6
Real Time Clock
Intel(R) 8 Series/C220 Series SMBus Controller 8C22
Numeric data processor
High Definition Audio Controller
Intel(R) 8 Series/C220 Series USB EHCI #2 - 8C2D
Intel(R) Management Engine Interface
Intel(R) 8 Series/C220 PCI-Express Root Port #1 8C10
Intel(R) Xeon(R) processor E3-1200 v3/4th Gen
Core processor PCI Express x16 Controller - 0C01
Intel(R) 8 Series/C220 Series SATA AHCI
Controller - 8C02
Intel(R) Active Management Technology - SOL
(COM7)
High Definition Audio Controller
Intel(R) 8 Series/C220 Series USB EHCI #1 - 8C26
MI981 User’s Manual
APPENDIX
C. Watchdog Timer Configuration
The WDT is used to generate a variety of output signals after a user
programmable count. The WDT is suitable for use in the prevention of
system lock-up, such as when software becomes trapped in a deadlock.
Under these sorts of circumstances, the timer will count to zero and the
selected outputs will be driven. Under normal circumstance, the user will
restart the WDT at regular intervals before the timer counts to zero.
SAMPLE CODE:
//--------------------------------------------------------------------------//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//--------------------------------------------------------------------------#include <dos.h>
#include <conio.h>
#include <stdio.h>
#include <stdlib.h>
#include "F81866.H"
//--------------------------------------------------------------------------int main (int argc, char *argv[]);
void EnableWDT(int);
void DisableWDT(void);
//--------------------------------------------------------------------------int main (int argc, char *argv[])
{
unsigned char bBuf;
unsigned char bTime;
char **endptr;
char SIO;
printf("Fintek 81866 watch dog program\n");
SIO = Init_F81866();
if (SIO == 0)
{
printf("Can not detect Fintek 81866, program abort.\n");
return(1);
}//if (SIO == 0)
if (argc != 2)
{
printf(" Parameter incorrect!!\n");
return (1);
}
bTime = strtol (argv[1], endptr, 10);
printf("System will reset after %d seconds\n", bTime);
if (bTime)
{
EnableWDT(bTime); }
else
{
DisableWDT();
}
return 0;
MI981 User’s Manual
61
APPENDIX
}
//--------------------------------------------------------------------------void EnableWDT(int interval)
{
unsigned char bBuf;
bBuf = Get_F81866_Reg(0x2B);
bBuf &= (~0x20);
Set_F81866_Reg(0x2B, bBuf);
//Enable WDTO
Set_F81866_LD(0x07);
Set_F81866_Reg(0x30, 0x01);
//switch to logic device 7
//enable timer
bBuf = Get_F81866_Reg(0xF5);
bBuf &= (~0x0F);
bBuf |= 0x52;
Set_F81866_Reg(0xF5, bBuf);
Set_F81866_Reg(0xF6, interval);
//count mode is second
//set timer
bBuf = Get_F81866_Reg(0xFA);
bBuf |= 0x01;
Set_F81866_Reg(0xFA, bBuf);
//enable WDTO output
bBuf = Get_F81866_Reg(0xF5);
bBuf |= 0x20;
Set_F81866_Reg(0xF5, bBuf);
//start counting
}
//--------------------------------------------------------------------------void DisableWDT(void)
{
unsigned char bBuf;
Set_F81866_LD(0x07);
//switch to logic device 7
bBuf = Get_F81866_Reg(0xFA);
bBuf &= ~0x01;
Set_F81866_Reg(0xFA, bBuf);
//disable WDTO output
bBuf = Get_F81866_Reg(0xF5);
bBuf &= ~0x20;
bBuf |= 0x40;
Set_F81866_Reg(0xF5, bBuf);
//disable WDT
}
//---------------------------------------------------------------------------
62
MI981 User’s Manual
APPENDIX
//--------------------------------------------------------------------------//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//--------------------------------------------------------------------------#include "F81866.H"
#include <dos.h>
//--------------------------------------------------------------------------unsigned int F81866_BASE;
void Unlock_F81866 (void);
void Lock_F81866 (void);
//--------------------------------------------------------------------------unsigned int Init_F81866(void)
{
unsigned int result;
unsigned char ucDid;
F81866_BASE = 0x4E;
result = F81866_BASE;
ucDid = Get_F81866_Reg(0x20);
if (ucDid == 0x07)
{
goto Init_Finish;
}
//Fintek 81866
F81866_BASE = 0x2E;
result = F81866_BASE;
ucDid = Get_F81866_Reg(0x20);
if (ucDid == 0x07)
{
goto Init_Finish;
}
//Fintek 81866
F81866_BASE = 0x00;
result = F81866_BASE;
Init_Finish:
return (result);
}
//--------------------------------------------------------------------------void Unlock_F81866 (void)
{
outportb(F81866_INDEX_PORT, F81866_UNLOCK);
outportb(F81866_INDEX_PORT, F81866_UNLOCK);
}
//--------------------------------------------------------------------------void Lock_F81866 (void)
{
outportb(F81866_INDEX_PORT, F81866_LOCK);
}
//--------------------------------------------------------------------------void Set_F81866_LD( unsigned char LD)
{
Unlock_F81866();
outportb(F81866_INDEX_PORT, F81866_REG_LD);
outportb(F81866_DATA_PORT, LD);
Lock_F81866();
}
//--------------------------------------------------------------------------void Set_F81866_Reg( unsigned char REG, unsigned char DATA)
{
Unlock_F81866();
outportb(F81866_INDEX_PORT, REG);
outportb(F81866_DATA_PORT, DATA);
Lock_F81866();
}
//---------------------------------------------------------------------------
MI981 User’s Manual
63
APPENDIX
unsigned char Get_F81866_Reg(unsigned char REG)
{
unsigned char Result;
Unlock_F81866();
outportb(F81866_INDEX_PORT, REG);
Result = inportb(F81866_DATA_PORT);
Lock_F81866();
return Result;
}
//---------------------------------------------------------------------------
//--------------------------------------------------------------------------//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//--------------------------------------------------------------------------#ifndef __F81866_H
#define __F81866_H
1
//--------------------------------------------------------------------------#define F81866_INDEX_PORT
(F81866_BASE)
#define F81866_DATA_PORT
(F81866_BASE+1)
//--------------------------------------------------------------------------#define F81866_REG_LD
0x07
//--------------------------------------------------------------------------#define F81866_UNLOCK
0x87
#define F81866_LOCK
0xAA
//--------------------------------------------------------------------------unsigned int Init_F81866(void);
void Set_F81866_LD( unsigned char);
void Set_F81866_Reg( unsigned char, unsigned char);
unsigned char Get_F81866_Reg( unsigned char);
//--------------------------------------------------------------------------#endif //__F81866_H
64
MI981 User’s Manual
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising