how to install interface module

how to install interface module
Before start, please read this manual first very carefully, take your time and work carefully. Always be sure to take proper
safety precautions when working with tools, this includes but is not limited to gloves, eye and ear protection, If you feel that you can not
complete any part of the installation, please seek professional help rather than risk your well being or the integrity of your BMW.
m
od
m
yn
av
.co
m
HOW TO INSTALL INTERFACE MODULE
.co
m
av
yn
od
m
m
1. Lift up the edge of your interior trim and remove
av
yn
od
m
m
.co
m
.co
m
av
yn
od
m
m
2. Unscrew 2 screws
.co
m
av
yn
od
m
m
3. Remove front dash panel, full it towards you carefully
.co
m
av
yn
od
m
m
4. Unscrew two screws (Trox #10)
.co
m
av
yn
od
m
m
5. Flip down and pull the screen towards you
.co
m
av
yn
od
m
m
6. Remove connector
.co
m
av
yn
od
m
m
7. Remove stock LCD cable from the screen
.co
m
av
yn
od
m
m
8. Open the glove box and remove 7 screws
av
yn
od
m
m
.co
m
av
yn
od
m
m
.co
m
.co
m
av
yn
od
m
m
9. Unscrew 4 screws and pull the radio unit towards you
.co
m
av
yn
od
m
m
10. Remove stock audio harness
.co
m
av
yn
od
m
m
11. Remove yellow circled connectors (you might have more than 2 or less as picture shown above, it depends on your option, remove
all removable connectors)
.co
m
av
yn
od
m
m
Lift up the tab to release connector
.co
m
av
yn
od
m
m
Press the tab to release the connector
.co
m
av
yn
od
m
m
12. Insert connectors (which you removed from stock harness) to PnP harness (Female) then connect to radio
.co
m
av
yn
od
m
m
13. Connect Stock radio harness to PnP Harness (Male Side)
.co
m
av
yn
od
m
m
14. Run CAN/Power connector and Back up camera power adapter from radio mount area to your screen area
.co
m
av
yn
od
m
m
15. Connect CAN/Power connector and AV(IN/OUT) cables to interface module and run these cable from screen area to glove box area
.co
m
av
yn
od
m
m
Should be like this (cables shown above isn’t connected so it might be shorter than pictured)
.co
m
av
yn
od
m
m
16. From back up camera extension cable, connect RCA cable to REAR-C input and Red connector to back up camera power adapter
* Check Back up camera DIY guide for the way to run the extension cable from the trunk to front.
* Connect any other multimedia devices to AV1~3 using composite AV cable if you wish to have video playback
.co
m
av
yn
od
m
m
17. Connect New LCD cable to screen
.co
m
av
yn
od
m
m
18. Connect LCD Cables to interface module (New LCD Cable to LCD-OUT and Stock LCD Cable to LCD-IN)
.co
m
av
yn
od
m
above
m
19. Connect CAN/Power connector to interface module and clean up the cables, then insert module into empty space as picture shown
20. Put everything back to stock and Enjoy!
m
od
m
yn
av
.co
m
ACTIVATE PARKING GUIDE LINE
m
od
m
yn
av
.co
m
IF YOU HAVE DISPLAY PROBLEM
HOW TO SWITCH VIDEO SOURCE
1. Press iDrive Controller “MENU” button for 2 seconds
.co
m
2. Press Down Arrow on your steering wheel for 2 seconds
Screen will switch from stock iDrive screen to : AV1 -> AV2 -> F-CAM (AV3)
* Simply press “MENU” button once to bring back your stock screen
HOW TO SPLIT YOUR SCREEN
av
Press “Source Change” button on your steering wheel for 2 seconds
yn
HOW TO MOVE YOUR PDC SCREEN ON REAR VIEW SCREEN
m
od
m
Press Down Arrow on your steering wheel to move PDC screen from left to right
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising