Magnum P62F - Belden Solutions
8-port Industrial Strength
10/100 Switch, P62F and P62F-5V
Magnum P62F
Features
• Ethernet Switch, provides
six 10/100 switched RJ-45
ports and two 100Mb fiber
ports
• Designed for unheated / un-
cooled “outdoor” applications such as roadside control boxes. Metal case and
pedestal mounting hardware serve as a heat sink to
dissipate internal heat
• P62F models provide two
100Mb fiber ports built in,
typically used to daisy-chain
units in a system
• Fast Ethernet fiber connec-
tors may be multi-mode SC,
20km single-mode SC, or
other specialty types
• Models for power sources
of -48VDC, 24VDC, or
12VDC. AC power usable
with Magnum PSX units
Magnum P62F-5V
Magnum P62F
When Ethernet LAN switches need to move out of temperature controlled friendly
offices and into harsh environments with inhospitable high/low temperatures,
the Magnum P62F and P62F-5V Switches can be the solution.
Two 100Mb switched fiber ports allow strings of P62Fs to be deployed
over great distances, and a half-dozen 10/100 switched RJ-45 ports in each unit
provide easy and convenient connectivity for local devices and users at each
drop.
Designed to operate in temperature uncontrolled applications, the P62F
case was engineered to function as a heat sink, to draw the heat away from the
internal electronics and dissipate it. In order to minimize the heat dissipation
problem, the efficient P62F uses just 10 watts of power. The P62F operates normally up to 70°C (160°F), withstanding the heat of summer in the desert and
down to the extreme cold of arctic winter -40°C (-40°F).
Since the P62F case is sealed, it prevents problem elements from entering the unit. There is no convection air flowing through the unit, no cooling fan
failure to worry about, and no spiders or insect penetration. In addition, the
P62F will allow no smoke inside, preventing internal damage to the electronics if
used adjacent to an accidental building or plenum fire.
Noteworthy applications for the P62F include roadside traffic data collection and control stations, unheated or high temperature industrial plant locations, plenums and ceiling locations in commercial buildings, data communications huts and pedestals, and military field operations sites.
When mounted in the field, the P62F is typically fastened to a metal
pedestal or post that is planted in the earth. This provides an even larger heat
sink to normalize the operating temperature of the electronics in the P62F. Although the P62F’s package is not waterproof, it can be placed in NEMA 4 boxes,
IP65 enclosures, and similar waterproof metal enclosures to provide an all-weather
outdoor solution.
The Magnum P62F and P62F-5V units are available with a choice of 100Mb
fiber port connectors; multi-mode and single-mode fiber cabling (and combinations) are supported as well. To achieve high performance, large (1MB) packet
buffers and 16K address tables are standard. DC power input is featured in model
P62F for high reliability and convenience in out-of-the-way locations. Standard
AC power can be applied to the model P62F-5V using the Magnum PSX-A Power
Source for Extended Temperature.
The ruggedness of the P62F steel case combined with the high reliability
of the design (over 15 years MTBF) complements the temperature-controlled
packaging to provide an exceptional “Industrial Strength” Ethernet product.
The Magnum P62F and P62F-5V Ethernet Switches as well as the other
Magnum products are designed and manufactured in the US and backed by a
three-year warranty.
Specifications
PERFORMANCE:
RJ-45 Ports: # 2-6 are 100 or 10Mb / second, auto-negotiating for speed
and F/H duplex mode.
Fiber Ports: # 1 and # 8 are 100Mb fiber, full-duplex
Processing type: Store and Forward, with IEEE 802.3x full duplex, flow
control non-blocking.
System aggregate forwarding and filtering rate: 1190K pps (packets per
second), 1190K pps @ 100BASE-TX/FX
Packet buffers: 1MB
Address Table size: 16K nodes
Latency: less than 5μs (not including packet time)
PDV: 50BT
NETWORK STANDARDS:
Ethernet: IEEE 802.3u, 100BASE-TX, FX; IEEE 802.3, 10BASE-T
Auto Negotiation: IEEE 802.3u, occurs at LINK enable, for each RJ-45
port
All 10Mb ports obey the rules for configuring 10Mb Ethernet, all 100Mb
ports use Fast Ethernet rules
OPERATING ENVIRONMENT:
Ambient Temperature: -40° to 160°F (-40° to 70°C)
Plenum rated for above-the-ceiling installation
Cold start down to -20°C
Storage:
-40° to 185°F (-40°to 85°C)
Ambient Relative Humidity: 10% - 95% (non-condensing)
Altitude: -200 to 50,000 ft. (-60 to 15,000m)
Operating Shock and Vibration: Meets Bellcore GR-63-CORE
Sections 4.4.1 and 4.4.3
NETWORK CABLE CONNECTORS:
Fiber: 100Mb Multi-mode SC, 100Mb Single-mode SC-type 20km (other
types available via RFQ)
RJ-45 shielded female
100Mb: Category 5 UTP/STP, 10 Mb: Cat. 3,4, 5 UTP
POWER SUPPLY (INTERNAL):
P62F Power Input: 20-60VDC auto-ranging, floating + and - lugs.
Typically for use where 24VDC or –48VDC power is available.
P62F-5V Power Input: 5VDC, screw-lock connector, typically for use with
Magnum PSX Power Source, rated for 15 watts at a temp. range of -40°C
to 70°C.
Power Consumption: 10 watts typical, 2A at 5VDC
Ordering Information
Model Number:
Magnum P62-AC-2MSC
Magnum P62-AC-1M1SSC
Magnum P62-AC-2SSC
Magnum P62-AC-NOF
Magnum P62-2MSC
Magnum mP62-1M1SSC
Magnum mP62-2SSC
Magnum mP62-NOF
Parts:
Magnum P62-5V-2MSC*
Magnum P62-5V-1M1SSC*
Magnum P62-5V-2SSC*
Magnum P62-5V-NOF
Magnum PSX-5V-CBL (spare)
8-port Industrial Strength
Ethernet Switch, Model P62F and P62F-5V
MECHANICAL:
Enclosure: Rugged 18-gauge high-strength steel case. The case
serves as a heat sink. Normally mounted vertically on a pedestal or
metal surface. DIN-rail mounting kit, optional.
Metal mounting base included, 13-gauge steel (without the base,
the box size is only 7” high). Mounting holes are a rectangle that
is 3.35” X 7.92” (8.5 X 20.1cm) center-to-center. The lip at the
bottom of the base can be used to anchor strain-relief for cables.
Mounting screws (user supplied): Slot can accomodate sizes up to
1/4” diameter.
Dimensions (wall mounted): 1.80 in D x 5.75 in W x 8.8 in H
(4.6 cm x 14.6 cm x 22.4 cm)
Weight of the unit: 3.5 lbs (1.6 Kg.)
Cooling Method: Convection, with case operating as a heat sink
Note: Internal steel brackets conduct heat from the electronic
elements inside to the P62F steel case which acts as a heat sink.
Internal chip temperatures are only about 10°C above case ambient during steady state operation.
LED INDICATORS ON CHASSIS:
LEDs are viewed from the top surface.
Power: Steady on when power applied
LED INDICATORS PER PORT:
Speed: ON = 100Mb; OFF = 10Mb (with LINK On)
Link/Act: Steady ON for LINK with no traffic, blinking indicates
port is transmitting and receiving
F/H: ON for full-duplex mode, OFF for half-duplex
AGENCY APPROVALS AND STANDARDS COMPLIANCE:
UL Listed (UL60950), cUL, CE, Emissions meet FCC Part 15,Class A
NEBS L3 and ETSI compliant
IEEE 1613 Environmental Std for Electric Power Substations
IEC61850 EMC & Operating Cond. Class C for Pwr Substations
NEMA TS-2 and TEES for traffic control equipment
MEAN TIME BETWEEN FAILURE (MTBF):
15+ years, Bellcore Method.
WARRANTY :
Three years
Made in USA
©2009 GarrettCom, Inc. Printed in United States of America Doc No. P62F-11/09. GarrettCom,
Inc. reserves the right to change specifications, performance characteristics and/or
model offerings without notice. GarrettCom is a registered trademark of GarrettCom
Inc. Magnum, Dymec, DynaStar, S-Ring, and Link-Loss-Learn are trademarks of
GarrettCom, Inc. NEBS is a registered trademark of Telcordia. UL is a registered
trademark of Underwriters Labs.
P62-AC Managed Ethernet Switch with six 10/100 RJ-45 and two 100Mb FDX fiber multi-mode
SC-type ports. Has 4K nodes address table and 256KB packet buffers. AC power input, 85260vac 47-63Hz worldwide auto-ranging, via PSX-A Power Source Extended Temp (a separate unit).
Steel case used as a heat sink, designed for use in environmentally challenged locations such as
extended temperature “outdoors.”
Same as P62-AC-2MSC, except one fiber port is 20km single-mode SC. (includes PSX-A)
Same as P62-AC-2MSC, except both fiber ports are 20km single-mode SC. (includes PSX-A)
P62-AC Ethernet Switch with six 10/100 RJ-45 and no fiber ports.
P62-DC Ethernet Switch, six 10/100 RJ-45 and two 100Mb FDX fiber multi-mode SC-type
ports. Software and buffers same as P62-AC-2MSC. DC power input, 18-70VDC autoranging.
Same as P62-2MSC, but with one multi-mode SC-type and one 20Km single-mode SC fiber
connectors (No PSX unit required).
Same as P62-2MSC, except both 20Km single-mode SC fiber connectors (No PSX unit
required).
P62-DC Ethernet Switch with six 10/100 RJ-45 and no fiber ports
Same as P62-2MSC, except with 5VDC input using military-type screw-lock connector.
Same as P62-1M1SSC, except with 5VDC input using military-type screw-lock connector.
Same as P62-2SSC, except with 5VDC input using military-type screw-lock connector.
Same as P62-NOF, except w/ 5VDC input via PSX-A using military-type screw-lock
connector.
2-ft power cord with military-type screw-lock connector, spare for PSX to mP62-5V power cord.
* PSX unit or equal required to supply 5VDC input. For more information, please see the PSX datasheet.
For Magnum P62F and P62F-5V units with other fiber connector types, RFQ for additional information.
GarrettCom, Inc.
47823 Westinghouse Drive
Fremont, CA 94539
PH: (510) 438-9071
FAX (510) 438-9072
Email: mktg@garrettcom.com
Web: www.GarrettCom.com
Power Source, Extended
Temperature, for Magnum P62s
Features
• Provides power input to
the Magnum P62F
Ethernet Switches from
AC worldwide.
• Operates in ambient
temperatures of -40°C
to 75°C, for “Ethernet
Outdoors”
• Industrial grade surge
protection, overload
and short circuit protection, shock and vibration
rating
• Metal case used as a
heat sink, sealed unit
with no moving parts
• Military-style screw-lock
plug for secure 5VDC at
tachment to the P62
Switches
Magnum P62F Ethernet Switches used in industrial grade “Ethernet
Outdoors” applications need rugged power sources. These power
sources must withstand temperature extremes, hard knocks, and
surges from nearby lightening strikes. They must resist smoke and
fire, bugs and insects, dust and dirt. They must be reliable and longlasting in service.
Where AC power is used, the Magnum Model PSX-A is the solution.
It accepts all standard worldwide AC power voltages and frequencies. The military-style screw-lock plug provides a secure connection, delivering 5VDC power to the Magnum P62’s.
Since the PSX is sealed, it prevents problem elements from
entering the unit. There is no convection air flowing through the
unit, no cooling fan failure to worry about, and no spiders or insect
penetration. In addition, the plenum-rated PSX does not allow smoke
inside, preventing internal damage to the PSX in case of fire. The
PSX’s package is IEC 529 rated IP51 and, while not waterproof, it
can be placed in NEMA 4 boxes, IP65 enclosures and similar waterproof enclosures to provide an all-weather outdoor solution.
The Magnum PSX-A Power Source products as well as the
other Magnum products are designed and manufactured in the US
and backed by a three-year warranty.
Power Source, Extended
Temperature, for Magnum
P62s
Specifications
OPERATING ENVIRONMENT:
Ambient Temperature: -40° to 170°F (-40° to 75°C)
Cold start down to -20°C
Storage: -40° to 185°F (-40°to 85°C)
Ambient Relative Humidity: 5% - 95% (non-condensing)
Altitude: -200 to 50,000 ft. (-60 to 15,000m)
Plenum rated for above-the-ceiling installation
Conformal coating (humidity protection) option, request quote.
PSX units are IEC 529 rated IP51 (holds out dust, vertical water)
Operating Shock and Vibration: Meets Telcordia GR-63 Sections
4.4.1, 4.4.3
PERFORMANCE:
Electrical Efficiency: 70% min.
Power dissipation: 3 watts typical
Surge Protection: over 150 joules
Surge clamping: 800V, 50A min.
Overload and short circuit protection: Input fuse
POWER INPUT:
PSX-A
85-264vac, 47-63Hz, auto-ranging.
AC Power Connector: IEC-type, male recessed.
PSX-A
Input Fuse: 3AG type, 0.5 Amp; a spare is included
POWER OUTPUT:
5VDC, up to 3 Amps
DC Output Connector: 21 inch cord, +, GND, -, to military-style
screw-lock female plug.
Mounting: For best results at high-temperature, fasten the metal
case of the PSX unit to be in contact with a vertical metal surface
(such as a pedestal) that has good heat conducting properties. Remove rubber “feet,” if present, to enhance metal-to-metal contact
and provide the best heat transfer away from the PSX unit.
MECHANICAL:
Enclosure: Rugged 18-gauge high-strength steel case. The case
serves as a heat sink. Normally mounted vertically on a pedestal or metal surface. DIN-Rail mounting kit, optional.
Mounting screws (user supplied): Slot can accommodate sizes
up to 1/4” diameter.
Mounting Slots: 3.35 in. x 6.20 in. rectangle
(8.5cm x 15.75cm)
The bottom mounting slots match with the mounting slots at
top of Magnum P62 units.
Dimensions (wall-mounted):
1.5 in. D x 6.5 in. W x 6.5 in. H
(3.8cm D x 16.5cm W. x 16.5cm H)
Weight: 2 lb. (0.9kg)
Cooling Method: Convection, with case operating as a heat
sink
LED INDICATORS ON CHASSIS:
POWER indicates incoming power is ON.
AGENCY APPROVALS:
UL Listed (UL60950), cUL, CE, Emissions meet FCC Part 15, ClassA
NEBS L3 and ETSI compliant
IEEE 1613 Environmental Std for Electric Power Substations
IEC61850 EMC & Operating Cond. Class C for Pwr Substations
NEMA TS-2 and TEES for traffic control equipment
WARRANTY:
Three years
Made in USA
©2006 GarrettCom, Inc. Printed in United States of America Doc No. PSXT_PSXA-R7 8/06
GarrettCom, Inc. reserves the right to change specifications, performance characteristics and/or model
offerings without notice. GarrettCom, Magnum and Personal Switch are trademarks and Personal Hub
is a registered trademark of GarrettCom, Inc. NEBS is a registered trademark of Telcordia Technologies. UL is a registered trademark of Underwriters Labs.
Magnum PSX-A Power
Source shown with Magnum
P62F in a typical set-up.
Ordering Information
Magnum PSX-A
Magnum PSX-T
Magnum P62 Power Source for Extended Temperature, nominal AC input
115 to 240vac and 50 to 60Hz auto-ranging, 15 watts, 5VDC output, 21”
power cord to screw-lock plug. Steel case used as a heat sink. Mounts as a
separate unit adjacent to the Magnum P62 Switch. Operates from -40° to
75°C ambient.
Same as PSX-A, except 125VDC to 250VDC input, terminal lugs for +, - and
GND
GarrettCom, Inc.
47823 Westinghouse Drive
Fremont, CA 94539
PH: (510) 438-9071
FAX (510) 438-9072
Email: mktg@garrettcom.com
Web: www.GarrettCom.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising