Denver TCM-108 CD player User manual

Location of controls
(1)
FUNCTION SWITCH
CD/POWER OFF/RADIO
(10) CD REPEAT BUTTON
(2)
BAND SWITCH
(3)
FM ANTENNA
(12) CD PLAY/PAUSE BUTTON
(4)
CD DOOR
(14) STEREO HEADPHONE JACK
(5)
TUNING KNOB
(6)
BASS BOOST BUTTON
(15) VOLUME CONTROL KNOB
(7)
CD SKIP/SEARCH/FOLDER
FORWARD BUTTON
(17) BATTERY DOOR
(8)
CD SKIP/SEARCH/FOLDER
BACKWARD BUTTON
(19) SPEAKER LEFT
(9)
CD PROGRAM BUTTON
(11) CD STOP BUTTON
(13) CD LCD DISPLAY
(16) AC SOCKET
(18) FM STEREO LED INDICATOR
(20) SPEAKER RIGHT
English - 1
AC OPERATION
Before operation please be sure that the VOLTAGE on the set corresponds to
the VOLTAGE of your local area. Unravel the AC Line Cord, insert one end
into the AC jack on the set, and the other end into a standard AC outlet.
BATTERY OPERATION
Disconnect the AC Cord Set completely. Open the BATTERY COMPARTMENT
DOOR and insert UM-2/ “C” size x 8 batteries (not supplied) making sure that
the indicated battery polarity is observed.
RADIO OPERATION
Slide the FUNCTION switch to the “RADIO” position. Slide the BAND switch to
the desired waveband. Turn the TUNING KNOB to your desired radio station.
Adjust the sound level by rotating the VOLUME CONTROL KNOB. To turn off
the radio, simply slide the FUNCTION SWITCH to “POWER OFF” position.
NOTE : Radio frequency is shown on the tuning knob.
FM STEREO INDICATOR
When tuned to a FM stereo broadcast the “FM ST.” LED indicator will light up.
In weak signal areas the FM Stereo signal may not be strong enough and can
cause excessive background noise. In this case, switch to the “FM” position.
ANTENNAS
For best reception, fully extend the FM Antenna to receive FM stations. For
AM reception, the unit has a built-in antenna, turn the whole unit for best
reception.
BASS BOOST
For increased bass at all volume levels, slide the BASS BOOST BUTTON to
“ON” position to boost the low frequency tone for an emphasized bass sound.
To release the super bass, simply slide to “OFF” position.
STEREO HEADPHONE JACK
For private listening, insert the plug of a STEREO Headphone into the
STEREO HEADPHONE JACK and adjust the VOLUME CONTROL KNOB
accordingly. During the use of a headphone, the Speakers are automatically
disconnected.
English - 2
CD OPERATION
PLAYING COMPACT DISC (CD-R/RW PLAYBACK COMPATIBLE)
GETTING STARTED
NOTE: Should skipping of tracks occur during CD playing, try turning the
volume down.
When CD is playing, do not open the CD Door.
1. Open the CD DOOR by pull up the CD DOOR. Put a CD disc into the CD
COMPARTMENT and close the CD DOOR. Set the FUNCTION SWITCH to
“CD” position.
NOTE : Ensure the CD Door is closed properly and locked in place.
2. When the CD DOOR is closed with a CD
inside, total number of tracks of the
disc will be shown on the CD LCD
DISPLAY and will go to stop mode. (ex.
Total 17 tracks inside the disc).
3. If the CD DOOR is not closed or there
is no disc inside, the DISPLAY will show
“
” and go to stop mode.
PLAY/PAUSE MODE
1. When the PLAY/PAUSE BUTTON is
pressed during CD stop mode, the first
track will be played. The PLAY
INDICATOR “” will be shown on the
LCD DISPLAY. The CD LCD DISPLAY will
show the specific number of track being
played.
2. For interruption while the CD is playing,
press the CD PLAY/PAUSE BUTTON
once. The PAUSE INDICATOR “” will
be shown on the LCD DISPLAY.
3. Though the sound stops, the disc will
continue to spin. To re-start playing,
press the CD PLAY/PAUSE BUTTON once again. The music will start from
the exact position where it was interrupted.
4. To stop the CD, press the CD STOP BUTTON once whether the CD is in
Play or Pause mode.
5. To turn off the unit, slide the FUNCTION SWITCH to “POWER OFF”
position.
English - 3
REPEAT MODE
1. REPEAT 1 :
When the REPEAT BUTTON is pressed once,
the “REPEAT” INDICATOR will be shown on
the LCD DISPLAY. This single track of music
will be repeated.
2. REPEAT ALL:
When the REPEAT BUTTON is pressed twice,
the “ALL REPEAT” INDICATOR will be shown
on the LCD DISPLAY. The whole disc can be
played continuously.
3. TO CANCEL THE REPEAT FUNCTION
Press the REPEAT BUTTON until the REPEAT INDICATOR disappears
from the LCD DISPLAY.
SKIP AND SEARCH MODE
1. During play or pause mode, when CD SKIP/SEARCH/FOLDER or CD
SKIP/SEARCH/FOLDER Button is pressed once, it will go to the next
track or go back to the beginning of the track.
2. During play mode, when CD SKIP/SEARCH/FOLDER or CD
SKIP/SEARCH/FOLDER BUTTON is pressed and held, it will search the
track with audible high-speed forward or backward playback.
Program Mode
1. During the CD stop mode, press the
PROGRAM BUTTON once. The
PROGRAM INDICATOR “PROG” will
light up and blink continuously while
the CD LCD DISPLAY will show the
number of Program to be memorized
starts from the first program “
”.
The track number is to be memorized will show “
” and blink
continuously as well. Press the CD SKIP/SEARCH/FOLDER or
SKIP/SEARCH/FOLDER BUTTON to your desired musical track, the CD
LCD DISPLAY will show the appropriate track number. Press the
PROGRAM BUTTON to store the desired track in
memory.
2. Repeat above procedure until all desired tracks have
been programmed. A total of 20 tracks can be stored in
memory. After complete programming, LCD DISPLAY
English - 4
will show “
” and “PROG” indicator will flash continuously.
3. To start the PROGRAMMED playback,
press the CD PLAY/PAUSE BUTTON
once and the CD PLAY INDICATOR
“” will light up.
4. To check the program you have
stored after complete programming,
press the PROGRAM BUTTON step by
step during the CD stop mode.
Note : While PROGRAM INDICATOR is flashing, never press the CD
STOP BUTTON otherwise all programmed memory will be
cancelled automatically.
5. To cancel the PROGRAMMED memory :
¾ Press the PROGRAM BUTTON once, “PROG” indicator is flashing on
the LCD DISPLAY, then press the CD STOP BUTTON.
OR
¾ Open the CD Door during the CD stop mode.
PLAYING MP3 DISC
GETTING STARTED
NOTE: Should skipping of tracks occur during CD playing, try turning the
volume down.
When MP3 disc is playing, do not open the CD Door.
1. Open the CD DOOR by pull up the CD DOOR. Put a MP3 disc into the CD
COMPARTMENT and close the CD DOOR. Set the FUNCTION SWITCH to
“CD” position.
NOTE : Ensure the CD Door is closed
properly and locked in place
2. When the CD DOOR is closed with a
MP3 disc inside, the total number of
folders and tracks of the disc will be
shown on the CD LCD DISPLAY and go
to stop mode. MP3 indicator will be
shown on the LCD DISPLAY as well to indicator MP3 disc is being played.
3. If the CD DOOR is not closed or there is
no disc inside, the DISPLAY will show
“
” and go to stop mode.
English - 5
PLAY/PAUSE MODE
1. When the PLAY/PAUSE BUTTON is
pressed during CD stop mode, the
first track will be played. The PLAY
INDICATOR “” will be lighted. The
CD LCD DISPLAY will show the
specific folder and track number
being played.
NOTE :
a. If the MP3 disc is downloaded without dividing into folder, then only
“
” will show on the Folder number.
”
b. If the MP3 disc is downloaded with several folders inside, then “
will always be shown in the Folder number when you first play the disc.
(“
” will never be shown in this case because it represents all the
tracks and folders inside this MP3 disc).
2. For interruption while MP3 disc is playing, press the CD PLAY/PAUSE
BUTTON once. The PAUSE INDICATOR “” will be shown on the display.
3. Though the sound stops, the disc will continue to spin. To re-start playing,
press the CD PLAY/PAUSE BUTTON once again. The music will start from
the exact position where it was interrupted.
4. To stop the MP3 disc, press the CD STOP BUTTON once whether the MP3
disc is in Play or Pause mode.
5. To turn off the unit, slide the FUNCTION SWITCH to “POWER OFF”
position.
REPEAT MODE
1. REPEAT 1 :
When the REPEAT BUTTON is pressed
once, the “REPEAT” INDICATOR will
light. This single track of music will be
repeated.
2. REPEAT FOLDER :
When the REPEAT BUTTON is pressed
twice, the “REPEAT FOLDER” indicator
will be shown. This specific folder will
be played repeatly.
English - 6
3. REPEAT ALL :
When the REPEAT BUTTON is pressed
three times, the “ALL REPEAT”
INDICATOR will be shown. The whole
disc can be played continuously.
4. TO CANCEL THE REPEAT FUNCTION
Press the REPEAT BUTTON until the REPEAT INDICATOR disappears from
the LCD DISPLAY.
SKIP AND FOLDER
1. During play or pause mode, when CD SKIP/SEARCH/FOLDER or CD
SKIP/SEARCH/FOLDER Button is pressed once, it will go to the next
track or go back to the beginning of the track.
2. During play or pause mode, when CD SKIP/SEARCH/FOLDER or CD
SKIP/SEARCH/FOLDER BUTTON is pressed once and held, it will go to
the next or previous folder for speed track selection.
NOTE : There has no search function in MP3 playback.
Program Mode
1. During the CD stop mode, press the PROGRAM BUTTON once. The
PROGRAM INDICATOR will light up and blink continuously while the CD
LCD DISPLAY will show the number of Program to be memorized starts
”. The track number is to be memorized will
from the first program “
show “
” and blink continuously as well. Press the
CD SKIP/SEARCH/FOLDER or CD
SKIP/SEARCH/FOLDER BUTTON to your desired
musical track, the CD LCD DISPLAY will show the
appropriate track number. Press the PROGRAM BUTTON
to store the desired track in memory.
2. Repeat above procedure until all desired tracks have
been programmed. A total of 20 tracks can be stored in
memory. After complete programming, LCD DISPLAY
will show “
” and the “PROG” indicator will blink
continuously.
3. To start the PROGRAMMED playback, press the CD PLAY/PAUSE BUTTON
once and the CD PLAY INDICATOR “” will light up.
4. To check the program you have stored after complete programming,
press the PROGRAM BUTTON step by step during CD stop mode.
English - 7
Note : While PROGRAM INDICATOR is flashing, never press the CD
STOP BUTTON otherwise all programmed memory will be
cancelled automatically.
5. To cancel the PROGRAMMED memory :
¾ Press the PROGRAM BUTTON once, “PROG” indicator is flashing on
the LCD DISPLAY, then press the CD stop BUTTON.
OR
¾ Open the CD Door during the CD stop mode.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE APPLIANCE TO
RAIN OR MOISTURE. DO NOT REMOVE COVER, PILOT LAMPS SOLDERED IN
PLACE. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
English - 8