canter 9c18 duonic - fuso

canter 9c18 duonic - fuso
FUSO – A Daimler Group Brand
1995 mm
2205 - 2210 mm
CANTER 9C18 DUONIC®
1140 mm
4985
5725
6470
7210
Max. body length**
3400
3850
4300
4750
Wheelbases
6725
6725
7225
7775
Total vehicle length
Front overhang
Mass/Dimensions
Model
Vehicle type
9C18
Cab type
Wide, Single / 3
MB model code
FUSO model code
46851512
46851712
46851812
46851915
FECX1EL3SEAU
FECX1GL3SEAU
FECX1HL3SEAU
FECX1KL3SEAU
DIMENSIONS mm
Wheelbase
3400
3850
Overall length
6725
Cabin length
1625
Overall width
2135
Cabin width
4750
7775
1995
Overall height, approx.
Tread
4300
7225
2210
2205
Front / Rear
1665 / 1670
Frame height (back of chassis) approx.
830
835
830
Cab to rear axle
2875
3325
3775
4225
Cab to frame end
4270
5020
5520
6070
Max. body length**
4985
5725
6470
7210
1745
1845
2605
2625
Ground clearance, approx.
185
Frame width
850
Front overhang
1140
Rear overhang (to frame end)
1395
1695
Front axle to beginning of body
625
Recommended cab to body gap
100
WEIGHTS kg
Total curb weight*
2555
Front* / Rear*
1680
2570
875
1645
925
Minimum vehicle weight
1680
925
1695
930
2650
Max. GVW / Max. GCW
8550 / 12050
Axle loads
Front / Rear
3100 / 6000
Trailing load
Braked / Non-braked
3500 / 750
Chassis Payload
5995
5980
5945
5925
CALCULATED PERFORMANCE
Max. speed w/o speed limiter
km/h
129
Max. gradeability
(tan q)%
30
Min. turning radius (m)
Curb to curb
12.2
13.8
15.2
16.6
Wall to wall
13.8
15.2
16.6
18.0
* including coolant, oils, 90% fuel, spare tire, tools and 75 kg driver; ** calculated maximum value. Should be checked based on installed body and application
Subject to change without notice. All the information in this data sheet should be viewed as indicative. The illustrations may show accessories and items of special equipment which are not part
of standard specification. This data sheet may also contain models and services which are not available in certain countries.
Version 1.1 / June 2013
FUSO – A Daimler Group Brand
CANTER 9C18 DUONIC®
Engine/Drive line/Chassis
ENGINE (Euro VI)
Model
4P10-AAT6
Type
4 stroke, turbo-charged water cooled direct injection diesel engine with intercooler
No. of cylinders
4 in line
Piston displacement
2998 cm3
Max. output (EEC)
129 kW (175 PS) / 3500 rpm
Max. torque (EEC)
430 Nm / 1600 rpm
Diesel particulate filter
Life span approx. 300000 km
Alternator
A.C. 12 Volt, 140 Amp
Emissions aftertreatment
EGR + SCR + DPF
Emissions level
PTO
Euro VI
Type
31 kW with flange
62 kW with flange
31 kW for direct connected pumps
Torque at max power
196 Nm
392 Nm
196 Nm
PTO Ratio
1:0.655
1:0.727
1:0.651
PTO speed at max power
1500 rpm
DRIVE LINE
Transmission
Model
M038S6 (DUONIC® dual-clutch automated manual transmission)
Type
Automated manual transmission, 6 forward and 1 reverse speed
Gear ratio
Final reduction gear
5.397 - 3.788 - 2.310 - 1.474 - 1.000 - 0.701 Rev. 5.397
Ratio
5.714 (Opt. 6.166)
Model
F350T / R035T
CHASSIS
Front axle / Rear axle
Rating
Tyre
3100 kg / 6000 kg
205/75R17.5C 124/122M
Single front, dual rear, optimized rolling resistance tyres
Wheel
17.5 x 6.00 - 127 - 6 stud
Steering
Left hand drive
Steering bevel gear and power steering with rack & pinion gear, tilt and telescopic column with steering lock
Brake
Service
Front / Rear
Parking
Auxiliary
Suspension
Front / Rear
Frame
Type
Fuel tank capacity
Electrical system – batteries
Hydraulic vacuum assisted 2 circuit split system
Disc (252 x 40)
Mechanical, internal expanding type mounted on the rear end of the transmission case
Exhaust brake (50 kW)
Semi-elliptic laminated leaf spring with shock absobers and stabilizer
C-Profile ladder frame
100 l
12V-100AH (760A EN)
Version 1.1 / June 2013
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising