Moxa Technologies NPort 5100 Series Quick Installation Manual

Adjustable pull high/low resistor for RS-422/485
(150 KΩ or 1 KΩ)
NPort 5100 Series
Jumpers are used to set the
pull high/low resistor values.
The default is 150 KΩ. Short
the jumpers to set this value to
1 KΩ. Do not use the KΩ
setting with RS-232 mode,
since doing so will degrade the
RS-232 signals and shorten
the communication distance.
Quick Installation Guide
Third Edition, January 2011
1. Overview
NPort 5100 series device servers are compact, palm-sized data
communication devices that allow you to control RS-232 (NPort
5110), RS-422/485 (NPort 5130), and RS-232/422/485 (NPort
5150) serial devices over a TCP/IP-based Ethernet.
Note: “-T” indicates an extended temperature model.
4. Hardware Installation Information
2. Package Checklist
Before installing the NPort 5100 series device server, verify that
the package contains the following items:
•
•
•
•
•
1 NPort 5100 series 1-port serial device server
4 stick-on pads
Documentation and software CD
Quick Installation Guide
Warranty card
Optional Accessory
•
DK-35A: DIN-Rail Mounting Kit (35 mm)
Notify your sales representative if any of the above items are missing or
damaged.
3. Hardware Introduction
NOTE The NPort 5110, NPort 5130, and NPort 5150 have the
same form factor.
Reset Button—Press the Reset button continuously for 5 sec to
load factory defaults: Use a pointed object, such as a straightened
paper clip or toothpick, to press the reset button. This will cause
the Ready LED to blink on and off. The factory defaults will be
loaded once the Ready LED stops blinking (after about 5 seconds).
At this point, you should release the reset button.
LED Indicators—NPort 5100’s top panel has three LED indicators,
which are described in the following table.
LED Name LED Color
Ready
Red
As shown in the following figures, NPort 5100 series device servers
have one male DB9 port for transmitting RS-232 (NPort 5110),
RS-422/485 (NPort 5130), or RS-232/422/485 (NPort 5150) serial
data.
Green
Off
Link
Tx/Rx
P/N: 1802054000312
–1–
Orange
LED Function
Steady on: Power is on and NPort is
booting up.
Blinking:
Indicates an IP conflict, or
DHCP or BOOTP server is not responding
properly.
Steady on: Power is on and NPort is
functioning normally.
Blinking:
The NPort has been located
by NPort Administrator’s Location function
Power is off, or power error condition
exists.
10 Mbps Ethernet connection.
Green
100 Mbps Ethernet connection.
Off
Orange
Ethernet cable is disconnected, or has a
short.
Serial port is receiving data.
Green
Serial port is transmitting data.
Off
No data is being transmitted or received
through the serial port.
–2–
STEP 1: After removing the NPort 5100 series device server from
the box, connect the NPort 5100 series device server to a network.
Use a standard straight-through Ethernet cable to connect to a hub
or switch. When setting up or testing the NPort 5100 series device
server, you might find it convenient to connect directly to your
computer’s Ethernet port. In this case, use a cross-over Ethernet
cable.
STEP 2: Connect the NPort 5100 series device server’s serial port
to a serial device.
STEP 3: Connect the power adaptor.
STEP 4: Placement options
In addition to placing
the NPort 5100 on a
desktop or other
horizontal surface,
you may also make
use of the DIN-Rail or
Wall Mount options,
as illustrated here.
Wall Mount DIN-Rail
5. Software Installation Information
To install NPort Administration Suite, insert the NPort
Document & Software CD into your computer’s CD-ROM drive.
Once the NPort Installation CD window opens, click on the
Installation button, and then follow the instructions on the
screen.
–3–
To view detailed information about NPort Administration Suite,
click on the Documents button, and then select “NPort 5100
Series User’s Guide” to open the pdf version of the user’s guide.
NPort 5150—DB9 male (RS-232/422/485) port pinouts
6. Pin Assignments
Ethernet Port Pinouts
Pin Number
1
2
3
6
Ethernet
Tx+
TxRx+
Rx-
NPort 5110—DB9 male (RS-232) port pinouts
Pin Number
RS-232
1
2
3
4
5
6
7
8
9
DCD
RxD
TxD
DTR
GND
DSR
RTS
CTS
---
RS-422/485
(4W)
TXD-(A)
TXD+(B)
RXD+(B)
RXD-(A)
GND
---------
RS-485 (2W)
----Data+(B)
Data-(A)
GND
---------
7. Specifications
Pin Number
1
2
3
4
5
6
7
8
9
Power Requirements
Power Input
12 to 48 VDC
Power Consumption
NPort 5110: 128.7 mA@12V, 72 mA@24V
NPort 5130: 200 mA@12V, 106 mA@24V
NPort 5150: 200 mA@12V, 106 mA@24V
Operating
0 to 55°C (32 to 131°F), for standard
Temperature
models
-40 to 75°C (-40 to 167°F), for -T models
Operating Humidity
5 to 95% RH
Dimensions
75.2 × 80 × 22 mm
including
(2.96 × 3.15 × 0.87 in)
ears
RS-232
DCD
RxD
TxD
DTR
GND
DSR
RTS
CTS
---
NPort 5130—DB9 male (RS-422/485) port pinouts
52 × 80 × 22 mm
(2.05 × 3.15 × 0.89 in)
Serial Line Protection
Magnetic Isolation
Power Line Protection
Regulatory Approvals
Pin Number RS-422/485 (4W)
1
TXD-(A)
2
TXD+(B)
3
RXD+(B)
4
RXD-(A)
5
GND
6
--7
--8
--9
---
–4–
without ears
15 KV ESD for serial port
1.5 KV for Ethernet
Level 2 Burst (EFT), EN61000-4-4
Level 2 Surge, EN61000-4-5
FCC Class A, CE Class A, UL, LVD
RS-485 (2W)
----Data+(B)
Data-(A)
GND
---------
www.moxa.com/support
The Americas:
Europe:
Asia-Pacific:
China:
+1-714-528-6777 (toll-free: 1-888-669-2872)
+49-89-3 70 03 99-0
+886-2-8919-1230
+86-21-5258-9955 (toll-free: 800-820-5036)
 2011 Moxa Inc., All Rights Reserved
–5–
–6–