SBD-1 Manual

SBD-1 Manual
1M23N23403
Before using your new SBD-1, please read this manual
thoroughly and use the system properly and safely.
After reading this manual, store it in a safe place.
S.BUS Decoder
Thank you for purchasing an SBD-1, S.BUS *1
decoder. The SBD-1 is a converter for using
conventional servos (other than S.BUS servo*2) with
the S.BUS system.
*1
S.BUS: Serial communication system for Futaba R/C system
*2
Use the S.BUS hub as the extension code used for the S.BUS
servo. Also SBD-1 can be used.
Applicable receiver: S.BUS system receiver only
INSTRUCTION MANUAL
Usage Precautions
•Channel setting by SBC-1
1Connect
the S.BUS connector of the SBD1 to the S.BUS servo connection port of the
SBC-1.
2C o n n e c t t h e b a t t e r y t o t h e b a t t e r y
connection port of the SBC-1.
CAUTION
When using analog servos, always use in
the state in which the receiver is normal
mode. There is the danger of erroneous operation
or damage on the high speed mode.
Futaba Corp. will not be responsible for
damage caused by combination with other
than Futaba Genuine parts.
Name of Each Part and Accessories
p r e s s a n d r e l e a s e t h e SBC1 setting switch and select the ser vo
connection port at which the channel is to
be set.
*Each time the switch is pressed, the set servo
connection port and the number of times the LED
blinks change.
<Accessories>
Channel No. Label
SBD-1
•Put the channel No. label on the servo connector
for the identification of channel No..
Instruction manual (this manual)
Connector (SX2)
selected.
Switch pressed
and released
quickly
Connector (SX3)
selected.
3 s h o r t bl i n k s
each second
Connector (SX1)
selected.
1Connect the S.BUS connector of the SBD1 to the receiver S.BUS connection port or
S.BUS hub.
2Connect a conventional servo or an S.BUS
servo to the servo connector of the SBD-1.
*When an S.BUS servo was connected, that servo
will operate as a conventional servo. However,
it operates on the channel set at the servo
connector of the SBD-1 instead of the channel set
at the servo itself.
to the receiver S.BUS connection port or S.BUS hub
Conventional servo
(or S.BUS servo)
SX1
the SBC-1 channel selector switch to
the channel you want to set.
5Hold down the setting switch (about 1
second).
SX2
SX3
Meaning of Special Markings
SX1
[SBD-1 Ratings]
Pay special attention to safety where indicated by the following marks:
(Middle)
SX2
DANGER
Procedures which may lead to dangerous conditions and
cause death/serious injury if not carried out properly.
WARNING
Procedures which may lead to a dangerous condition or
cause death or serious injury to the user if not carried out
properly, or procedures where the probability of superficial
injury or physical damage is high.
CAUTION
Procedures where the possibility of serious injury to the user
is small, but there is a danger of injury, or physical damage,
if not carried out properly.
(Lower)
SX3
Servo connector
● T6K, T10J, T14SG (V4.0-), FX-22 (V4.0-)
*S.BUS decoder channel setting is impossible with
the S.BUS receiver R6108SB.
*SBD-Link software can be downloaded from the
home page of your region's Futaba importer.
SBD-1 s e r vo
connector selection
•Connection
4Set
Channel Setting
Before installing the SBD-1 to the fuselage, set
each channel at each servo connector (SX1~3).
The equipment by which a channel set is possible
● SBC-1 S.BUS channel changer
● CIU-2/3 USB adapter (SBD-Link software for
setting)
SBC-1
S e t t i n g sw i t c h LED display
operation
W h e n p o w e r 1 shor t blink
turned on
each second
Switch pressed 2 s h o r t bl i n k s
a n d r e l e a s e d each second
quickly
Usage Method
*(Channel confirmation)
When the operation position of the channel selector
switch and the channel set at the connector during
the SBD-1 servo connector selection coincide, the
LED changes to a steady light.
(Upper)
S.BUS connector
set the channel of other ser vo
connection por ts, quickly press and
release the setting switch and repeat steps
4 and 5.
3Q u i ck l y
Do not connect any device (gyro, battery,
etc.) other than servos to the servo
connector of the SBD-1. There is the danger of
erroneous operation or damage.
Do not connect an S.BUS connector
of the SBD-1 to other than an S.BUS
servo connection port. There is the danger of
erroneous operation or damage.
6To
*Status display LED blinks slowly. (About 1 sec/time)
WARNNG
Always use in the state in which the SBD1 is firmly attached to the fuselage of
the airplane or helicopter. There is the danger
of loss of control and crashing if the connector is
disconncted by vibration and shock.
*During channel setting, the LED blinks quickly
(about 5 times/sec). When the LED changes to a
steady light, channel setting is complete.
= Prohibited
•Dimensions:
41.8x12.3x8.4mm
(1.65x0.48x0.33in.)
(excluding protruding)
•Power requirement:
NiCd, NiMH 4 to 5 cells
equivalent battery (Futaba)
• O p e r a t i n g t e m p e r a t u r e
range: -10 to +45°
= Mandatory
©Copyright 2017. No part of this manual may be reproduced in any form without prior permission. The contents of this
manual are subject to change without prior notice. While this manual has been carefully written, there may be inadvertent
errors or omissions. Please contact our service center if you feel that any corrections or clarifications should be made.
FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan
©FUTABA CORPORATION
2017, 4
(2)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising