Whisper manual
Wing Area
Wing Load
Flying Weight
Drive System
Control System
: 1 700mm(66.9in)
: 1070mm (42.1in)
: 25.7dm (398.4in )
: 31.5g/dm (10.3oz/sq.ft)
: 810g(28.6oz)
: Outrunner Brushless Motor
: Brushless Speed Controller
: 4* Servo
: 11.1V 3S Li-polymer
: 2.4GHz Multifunctional Transmitter
Main Wing(Left)
36A04-02 Fuselage
Main Wing(Right)
Horizontal Tail(Left)
Horizontal Tail(Right)
36A04-06 Fuselage
Supporting Wood Frame
36A04-07 Canopy
Folding Propeller
36A04-09 Spinner
36A04-10 Wheel
Servo Box
Control Horn
36A04-13 Motor Mount
36A04-14 Motor
36A04-15 Transmitter
36A04-16 Receiver
36A04-17 Charger
36A04-18 ESC
36A04-19 Servo
36A04-20 Wire Line
36A04-21 Battery
Carbon Fiber Rod
36A04-24 Push Rod
36A04-25 Magnet
Fiberglass Rod
36A04-26 Screw
36A04-27 Decal
36A04-28 Manual
1. Install the elevator and rudder onto the fuselage.
2. Glue the motor onto the motor mount.
5. Connect the linkage of elevator and rudder.
3. Install the canopy then install the folding propeller and spinner.
6. Screw the servo on the cover of servo box , then connect the linkage , finally screw the servo box.
4. Insert the carbon tube into the plastic part , then glue the horizontal tail.
7. Install the main wing onto the fuselage.
Remove battery cover and install 8
alkaline or rechargeable AA batteries(not provided)
A. Turn off power before installing batteries.
B. Only use the same type of battery, do not mix brand type.
C. Replace all batteries at the same time with new ones.
D. Do not mix old and new batteries.
Throttle Max
Rudder Left
Elevator Down
Rudder Right
Aileron Left
Alleron Right
Elevator Up
Throttle Min
(Mode II, North/South America).
Airwing RC guarantees this product to be free of manufacturing faults and material defects. This product has been checked
and fine tuned individually by professional pilot and quality control pilot. The warranty does not cover any component parts
damaged by use and modification. Please visit http://www.airwingrc.com for updated product information.
This product is not a toy. It is not recommended for children under 14 years old and any minor should be accompanied by an
adult when operating. This product is a precision machine that requires proper assembly and setup to avoid accidents.
Failure to take caution when operating this product may result in serious injury or property damage. It is the owner’s
responsibility to operate this product in a safe manner. Manufacturer and its distributors are not responsible in any way for
any and all bodily injury(s) and/or property damage that may occur from the use of or caused by in any way this product.
●The product is not intended for those under 14 years of
age without proper adult supervision. The product is not
a toy. It is a precision machine requiring proper assembly
and setup to avoid accidents and it is the responsibility of
the owner to operate this product in a safe manner as it can
cause serious personal injury and damage to property due
to carelessness or misuse.
● The spinning rotors on this product can be dangerous!
When operating/flying, always be aware of the spinning
rotors. Be careful not to let them come close to your body,
other people or loose clothing. Keep your hands, fingers
and any articles of clothing away from the rotors.
● Do not attempt to disassemble or modify any of the
product components without the assistance of an
experienced RC user.
● Only use the correct type of battery to operate. Using
any wrong type of battery will damage the product and
possibly make it dangerous to operate.
● The motor(s) may get hot during use. Always allow 10-15
minutes between each flight for the motor to cool down. This
will prolong the life of your product.
● After each use, always allow the battery to cool down
before recharging. When charging the battery pack, do not
overcharge! If batteries get hot during charging, discontinue
charging immediately and disconnect the battery from the
charger. Never leave battery unattended while charging. If
you are unsure of how to charge this battery, please seek the
advice of experienced RC users. Never let children charge
the battery without adult supervision.
● Always turn on the transmitter before connecting
the battery on the model. When turning off the model, always
disconnect the battery first, and then turn off the transmitter.
If the order is reversed, the model may become uncontrollable
and cause serious damage.
● If you are in doubt of your ability to operate the model,
we strongly recommend that you seek assistance from
experienced RC users or join your local model flying
club to gain the required knowledge and skill. As the
manufacturer and distributor, we assume no liability for the use
of this product.
● Choose an appropriate operating site consisting of flat,
smooth ground, and clear open field. Do not operate near
buildings, high voltage cable lines, or trees to ensure safety
operation. Operate in safe area only, away from other people.
RC models are prone to accidents, failures, and crashes
due to a variety of reasons including, lack of maintenance,
pilot error, and radio interference. Pilots are responsible for
their actions and damage or injury occurring during the
● Never allow batteries to run low or you might lose control of
the model.
● Do not operate in inclement weather, such as rain, wind,
snow and darkness.
● You should complete a successful pre-flight check of your
radio equipment and model prior to each flight.
● The product is composed of precision electrical
components. It is critical to keep the product away from
moisture and other contaminants. Do not allow them to
get wet. Electrical damage may occur that could affect
safe operation.
● Plastic is very susceptible to damage or deformation due
to extreme heat and cold climate. Do not store the model near
any source of heat such as oven or heater. Store the model
indoors, in a climate-controlled, room temperature
● Before turning on your model and transmitter, please check
to make sure no one else is operating under the same
frequency. Frequency interference can cause your model,
or other’s models to crash. The guidance provided by
experienced RC users will be valuable for the assembly, tuning,
trimming, and actual first flight.
Charge the Li-Po battery pack
The battery should be fully changed in 2 hours. Disconnect the battery from the charger
when the charging process completed. Do not charge the battery unattended at all time.
Lithium Polymer (LiPo) Battery Warnings
● Never charge a lithium polymer battery with a charger designed for NiCd, NiMH, or any
other type of battery chemistry. Use ONLY charger designed for LiPo battery.
Do not leave LiPo battery unattended during charging.
Do not overcharge the battery.
Always place the battery on a heat resistant surface alone when charging.
Always put the LiPo battery inside a charging protection container while charging.
Do not allow LiPo cells to overheat at any time. Cells which reach greater than 140
Fahrenheit (60°C) will usually become damaged and will catch fire.
Do not allow LiPo cells on or near combustible materials including paper, plastic, carpets,
vinyl, leather, and wood, inside an R/C model or full size automobile.
Do not over discharge LiPo; doing so will damage the battery.
Do not expose LiPo cell to water or moisture at any time.
Do not store battery near open flame or heater.
Do not assemble LiPo cells or pre-assembled packs together with other LiPo cells or packs.
Always store LiPo battery in a secure location away from children.
Always remove the LiPo battery if model is involved in any kind of crash. Carefully inspect
the battery and connectors for even the smallest damage. CAUTION: cells may be hot!
Do not allow the electrolyte to get into eyes or on skin. Wash affected areas immediately
if they come into contact with electrolyte. Do not alter or modify connectors or wires of a
LiPo battery pack.
Always inspect the condition of the battery before charging and operationg.
Do not short circuit the LiPo battery.
Do not have contact with a leaky/damaged battery directly.
Do not charge battery out of recommended temperature rang (0°C-45°C)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF