DJI Focus Quick Start Guide-A

DJI Focus Quick Start Guide-A
DJI Focus Diagram
DJI FOCUS
Remote Controller
1
Quick Start Guide
1. Antenna
2
3
V1.2
11
12
2. Power Button
3. Communication Port
4. Marking Ring
5. Focus Wheel
4
6. Micro USB Port
13
7. Navigation Buttons
5
8. Quick Focus Buttons
9. OLED Screen
10
10. Stiffness Control
11. System Status LED
12. Hard Stop Screws
9
13. Backlight
8
6
7
16
14. Link Button
15. Lanyard Hole
16. Rosette Mount
17. Rear Screw
14
15
DJI FOCUS
www.dji.com
1
2
Motor
1. Gear
2. Gear Knob
3
6
3. Quick-Release Mount
4. Communication Ports
5
©2016 DJI. All Rights Reserved.
Printed in China.
5. Link Button
4
6. System Status Indicator
17
DJI FOCUS
Quick Start Guide
Attach the Neck Strap
Install the Antenna
Mount the Lens Gear Ring
Mount the lens gear ring if you are not
using a cinema lens with gear rings.
Insert the neck strap connector
while pulling on the button.
1. Choose the lens gear ring that best fits
your camera lens.
2. Tighten the screw.
2
Screw on the antenna.
1
●
●
●
Mount the Motor
Ensure the neck strap is attached securely.
Calibrate the Motor
Used with the Zenmuse X5
Turn on the remote controller by holding down the
power button for 2 seconds.
To mount the motor onto your camera support rod:
1. Loosen the knob on the quick-release mount
and slide the motor onto the support rod.
●
●
The motor gear can be mounted on either side of the
motor. To remove the gear, loosen the knob at the
center of the gear.
The motor supports a 15 mm rod diameter by default.
To mount it on a 19 mm rod, slide the step-down
adapters off the clamp.
3. Connect the communication port on the motor
to an external power source using the supplied
power cable. If you are using the Ronin-M,
connect the motor to the P-TAP Accessory
power port on the Ronin-M.
DJI Focus can work in wireless mode or cable mode. To
use cable mode, connect the communication ports on
the remote controller and motor using the data cable.
Motor Power Cable
●
●
●
Ensure the motor is mounted firmly.
DO NOT touch the motor when it is rotating.
Cable mode will take precedence over wireless mode.
DJI Focus is fully compatible with the Zenmuse X5 series gimbal and camera. To allow communication
between the two devices, connect the communication port on the Focus remote controller to the
CAN Bus port on the Inspire 1 remote controller using the dedicated CAN Bus cable.
If your camera lens has mechanical limits, use Auto
calibration. Otherwise, use Manual-Remote or
Manual-Hand calibration.
50.0%
Calibrate
Select Menu > Aperture > On to enable the Aperture Control.
To switch from focus control to aperture control, press the ‘D’ button and then follow the instructions in
the DJI GO app to operate the focus wheel.
Menu
Auto
Select Calibrate > Auto (Shortcut: Press the ‘A’ and
‘B’ buttons together). The motor gear will rotate in
both directions in turn to locate the mechanical
limits of your camera lens. When the calibration is
complete, select Back to apply the calibration or
Stop to cancel.
2. Tighten the knob, ensuring that the motor gear
and lens gear ring make good contact.
Ensure that the lens gear ring and camera lens
make good contact.
Ensure the lens gear ring screw is installed
properly to allow an unobstructed full range of
motion.
Manual-Remote
Select Calibrate > Manual-Remote > Start to
begin. Press the up arrow to rotate the lens in one
direction, and select OK when it reaches the desired
upper limit. Next, press the down arrow to rotate
the lens in the other direction, and select OK when it
reaches the desired lower limit.
●
●
●
Manual-Hand
Select Calibrate > Manual-Hand >
Start to begin. Rotate the lens
manually to the desired upper and
lower limits of your camera lens,
and select OK to confirm the limits.
Ensure that the Zenmuse X5 camera is set in AF mode.
The remote controller overrides the in-app controls. You will not be able to adjust the focus or aperture in the DJI GO app.
You can purchase the dedicated CAN Bus cable on the DJI Store.
Basic Operation
Turn the focus wheel to control the focus,
zoom or iris of your camera lens.
Refer to the user manual for more information.
http://www.dji.com/product/focus
●
The motor will automatically reserve a 1mm margin at both mechanical limits for protection.
※This Quick Start Guide is subject to change without prior notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising