DALRC QOSD product instructions V1.5

DALRC QOSD product instructions V1.5
DALRC QOSD product instructions V1.5
QOSD is a completely separate OSD system, simple operation. Do not need any flight
controllers‘s support and can work independently, with compass, barometer, gyroscope as well as
accelerometer built-in, complete flight data display (it can also be used in car models and ship
models, ). Support GPS, RSSI signal strength and can control OSD switch and other functions by
connecting with receiver
Technical Parameters:
Weight:4.8g
Dimension:36.7*19.6MM
Sensor:Compass, barometer, gyroscope, accelerometer
Operating Voltage:6-26V
GPS baud rate:NEMA 0813 4800/9600/19200/38400/57600/115200
1:Hardware Connection Description
2. QOSD buttons Operating Instructions
After enter QOSD homepage, short press the QOSD board button recording the home position
meanwhile clear time to 0 , Under the main page, press QOSD board button about 2 seconds enter
the OSD setup menu, short press to “next”,long press (about 2 seconds) to “YES / BACK.”
3. QOSD
LED indicator instruction
-When GPS off , LED light on
-With GPS Plug in , but positioning failed, LED light flashing
-When positioning success and automatic recorded home or manual recorded , LED becomes
breathing light
4. Remote control function:
QOSD support remote connection, we recommend using two-stage switch control
A toggle:Open or close OSD data
Quick toggle 6 times (3 times back and forth): Re-recording home position and reset the time
Quick toggle 8 times (4 times back and forth): re-record home position (not reset time)
Quick toggle 10 times (5 times back and forth): Reset time (not re-record home)
OSD home screen introduction:
1:Battery voltage display (single voltage 3.6V by flashing a warning, 2-6S automatic recognition)
2:Attitude angle display (P: pitch angle R: Roll angle)
3:Speed
4:Number of GPS satellites (6 stars over automatically record at home, short press the button to
manually record home)
5:Home direction indicator (square in the middle, the front of the screen that is the direction of
home)
6:The total voyage
7:Distance from home
8:Height
9:Azimuth (home and aircraft line and just north of where the angle, measured clockwise)
10:Head toward (just north of 0 °, calculated clockwise)
11:Remote RSSI signal strength (RSSI output requires Receiver support, not displayed by default)
12:Horizon (coincidence horizon, to facilitate the observation flight attitude)
13: Center of the screen icon (supports three kinds of icons, or off))
14: vertical speed
15: Latitude and longitude (LON: longitude
N:North)
LAT: latitude
E:East
W:West
S:South
16:Flight time (can be cleared by the key or remote control)
17:Maximum flight speed (default is not shown)
18:Maximum line distance (default is not shown)
QOSD data can be customized switch, user can display or close any of the contents, QOSD
interface display position can not be changed but CUSTOM custom interface display position can
be changed
QOSD setup instructions
QOSD is “point-and-shoot”style design, it can be used with very simple set.
After enter QOSD homepage, short press the QOSD board button recording the home position
meanwhile clear time to 0 , Under the main page, press QOSD board button about 2 seconds enter
the OSD setup menu, short press to “next”,long press (about 2 seconds) to “YES / BACK.”
1: first page setup menu
2:GPS baud rate settings: Optional GPS to 38400 baud, no need to set, if you do not take GPS,
GPS baud rate is set to turn off the OSD OFF closed NO GPS Home Tips
3 : Voltage calibration: use the meter to measure the battery voltage, and then set to the same
voltage
4:Remote RSSI signal calibration: Turn on the transmitter and receiver, the remote control close
to the receiver, RSSI line access, click recalibration
5: Video format settings: PAL and NTSC, such as the discovery of the insertion of the camera
without an image or without OSD overlay, pull out the camera to change the system can be (the
display should be PAL or NTSC standard)
6:OSD display type: QOSD for the default interface, such as QOSD interface data display is not
complete, switch to QOSD1. CUSTOM for the custom interface, each content can change the
location (can be changed in 10 MENU CUSTOM)
7 : Height Gets equipment: BARO is barometer. You can also use the GPS, is recommended
barometer
8:Auto setting home: ON OFF
9:Horizon Display:ON OFF
10:Custom Menu
11: second page setup menu
12:Directions acquisition device (AUTO, COMPASS, GPS, recommend the use of compass)
13:Mounting direction (FRONT BACK LEFT RIGHT, direction arrows GOSD ago)
14 : The rolling sense (the horizon does not coincide or the reverse is set, generally without
setting).
15:Pitch sense (the horizon does not coincide or reverse when set, generally without setting)
16:Boot sereen:ON OFF
17:Compass Calibration: horizontal rotating clockwise circle, then clockwise rotation of the front
down, the calibration was successful
18 : Horizontal calibration: the level of the aircraft, after entering the automatic calibration,
automatic exit the calibration, the installation is recommended to do a horizontal calibration
19:Reset: Restores all settings GOSD
20:Exit menu
21: third page setup menu (MENU CUSTOM)
22:Voltage display (switch position adjustment)
23:Time display (switch position adjustment)
24:Speed display (switch position adjustment)
25:Height of the display (switch position adjustment)
26:Direction of home display (switch position adjustment)
27:From the home display (switch position adjustment)
28:Total flight display (switch position adjustment)
29:Remote RSSI signal strength display (switch position adjustment)
30:Vertical speed display(switch position adjustment)
31: fourth page setup menu (MENU CUSTOM)
32:Latitude and longitude display (switch position adjustment)
33:The number of satellites display (switch position adjustment)
34:Azimuth display (switch position adjustment)
35:Head direction display (switch position adjustment)
36:Attitude angle display (switch position adjustment)
37:The maximum distance display (switch position adjustment)
38:Maximum speed is displayed (switch position adjustment)
39:Center of the screen display (switch position adjustment)
40:Previous Menu
41:Exit menu
42:fifth page of the setup menu (CUSTOM MENU submenu)
43:Display (ON OFF)
44:Row (from the left count)
45:Column (start counting from the top)
46:SAVE
Firmware upgrade:
Connection method
QOSD support online upgrade software, need to access the internet.
Press OSD button to insert power,OSD will enter the upgrade mode (LED flash),Note: need to
insert power and upgrade module at the same time in case the insufficient voltage of the upgrade
module,Select the correct COM number will connect automatically 。Please upgrade the font file
(Fonts) firstly when upgrading,After finish upgrade switch off the power, repeat the upgrade
mode once again,Re upgrade Firmware(Firmware),After the upgrade completed, you must reset
the OSD settings.
Other:
OSD Connect the power immediately after pressing the button, this model has a complete sensor
data, for professional players you refer!
OK:Compass POST OK
MAG:Compass raw data (three arrows indicate the data no problem)
GYRO:Gyro raw data
DMP: Stable posture filtered data
ACCE:Accelerometer
H:Altitude
PWM:Control channel data
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising