OPNFV(Brahmaputra) Compass4nfv Frequently Asked

OPNFV(Brahmaputra) Compass4nfv Frequently Asked
OPNFV(Brahmaputra) Compass4nfv
Frequently Asked Questions
Release draft (862d2ec)
OPNFV
August 17, 2016
CONTENTS
1
What is Compass4nfv
3
2
What’s the additional setting in switch if use the default network configuration
5
3
How to deal with installation failure caused by setting pxe and reset nodes failed
7
4
How to deal with installation failure caused by “The Server quit without updating PID file”
9
5
How to set OpenStack Dashboard login user and password
11
6
How to visit OpenStack Dashboard
13
7
How to access BM nodes after deployment
15
8
Where is OpenStack RC file
17
9
How to recovery network connection after jumpserver reboot
19
10 References
21
i
ii
OPNFV(Brahmaputra) Compass4nfv Frequently Asked Questions, Release draft (862d2ec)
Contents:
CONTENTS
1
OPNFV(Brahmaputra) Compass4nfv Frequently Asked Questions, Release draft (862d2ec)
2
CONTENTS
CHAPTER
ONE
WHAT IS COMPASS4NFV
Compass4nfv is an installer project based on open source project Compass, which provides automated deployment
and management of OpenStack and other distributed systems. It can be considered as what the LiveCD to a single box
for a pool of servers – bootstrapping the server pool.
see more information, please visit
OPNFV Compass4nfv project page
COMPASS Home Page
3
OPNFV(Brahmaputra) Compass4nfv Frequently Asked Questions, Release draft (862d2ec)
4
Chapter 1. What is Compass4nfv
CHAPTER
TWO
WHAT’S THE ADDITIONAL SETTING IN SWITCH IF USE THE
DEFAULT NETWORK CONFIGURATION
Here is the Compass4nfv default network configration file: compass4nfv/deploy/conf/network_cfg.yaml
It uses a VLAN network for mgmt and storage networks that are share one NIC(eth1) as a default network configuration. So you need add an additional tagged VLAN (101) and VLAN (102) on eth1’s switch for access.
5
OPNFV(Brahmaputra) Compass4nfv Frequently Asked Questions, Release draft (862d2ec)
6
Chapter 2. What’s the additional setting in switch if use the default network configuration
CHAPTER
THREE
HOW TO DEAL WITH INSTALLATION FAILURE CAUSED BY SETTING
PXE AND RESET NODES FAILED
At first, please make sure that deployed nodes’ ipmi network can access from Jumphost and IPMI user/pass is correct.
Compass4nfv supports IPMI 1.0 or IPMI 2.0 to control your nodes, so you can set it according your IPMI version in
dha.yml.
ipmiVer: '2.0'
7
OPNFV(Brahmaputra) Compass4nfv Frequently Asked Questions, Release draft (862d2ec)
8
Chapter 3. How to deal with installation failure caused by setting pxe and reset nodes failed
CHAPTER
FOUR
HOW TO DEAL WITH INSTALLATION FAILURE CAUSED BY “THE
SERVER QUIT WITHOUT UPDATING PID FILE”
If you see “The Server quit without updating PID file” in installation print log, it is caused by mgmt network can’t
access from each deployed nodes, so you need to check your switch setting whether an additional tagged VLAN is
added if uses default network configuration.
9
OPNFV(Brahmaputra) Compass4nfv Frequently Asked Questions, Release draft (862d2ec)
10 Chapter 4. How to deal with installation failure caused by “The Server quit without updating PID
file”
CHAPTER
FIVE
HOW TO SET OPENSTACK DASHBOARD LOGIN USER AND
PASSWORD
It uses admin/console as the default user/pass for OpenStack Dashboard, and you can set it in below file: compass4nfv/deploy/conf/base.conf
11
OPNFV(Brahmaputra) Compass4nfv Frequently Asked Questions, Release draft (862d2ec)
12
Chapter 5. How to set OpenStack Dashboard login user and password
CHAPTER
SIX
HOW TO VISIT OPENSTACK DASHBOARD
You can visit OpenStack Dashboard by URL: http://{puclib_vip}/horizon
The public virtual IP is configured in “compass4nfv/deploy/conf/network_cfg.yaml”, defined as below:
public_vip:
ip: 192.168.50.240
13
OPNFV(Brahmaputra) Compass4nfv Frequently Asked Questions, Release draft (862d2ec)
14
Chapter 6. How to visit OpenStack Dashboard
CHAPTER
SEVEN
HOW TO ACCESS BM NODES AFTER DEPLOYMENT
1. First you should login Compass VM via ssh command on JumpHost by default user/pass root/root. The default
login IP of Compass VM is configured in “compass4nfv/deploy/conf/base.conf”, defined as below:
export MGMT_IP=${MGMT_IP:-192.168.200.2}
2. Then you can login the BM nodes (host1-3) by default user/pass root/root via the install network IPs which are
configured in “compass4nfv/deploy/conf/base.conf”, defined as below:
export MANAGEMENT_IP_START=${MANAGEMENT_IP_START:-'10.1.0.50'}
+-------------+
|
|
+----------+
host1
|
|
|
|
|
+-------------+
|
+---------+
|
+-------------+
|
|
install |
|
|
| Compass +---------------+----------+
host2
|
|
|
network |
|
|
+---+VM+--+
|
+-------------+
+--------------------+
|
|
|
|
+-------------+
|
JumpHost
|
|
|
|
|
|
+----------+
host3
|
+--------------------+
|
|
+-------------+
15
OPNFV(Brahmaputra) Compass4nfv Frequently Asked Questions, Release draft (862d2ec)
16
Chapter 7. How to access BM nodes after deployment
CHAPTER
EIGHT
WHERE IS OPENSTACK RC FILE
It is located /opt/admin-openrc.sh in each BM node as default. Please source it first if you want to use OpenStack CLI.
17
OPNFV(Brahmaputra) Compass4nfv Frequently Asked Questions, Release draft (862d2ec)
18
Chapter 8. Where is OpenStack RC file
CHAPTER
NINE
HOW TO RECOVERY NETWORK CONNECTION AFTER
JUMPSERVER REBOOT
source deploy/network.sh && save_network_info
19
OPNFV(Brahmaputra) Compass4nfv Frequently Asked Questions, Release draft (862d2ec)
20
Chapter 9. How to recovery network connection after jumpserver reboot
CHAPTER
TEN
REFERENCES
For more information on the Compass4nfv FAQ, please visit
COMPASS FAQ WIKI Page
21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising