Specification of Model SW-9576-CXX Preliminary

Specification of Model SW-9576-CXX Preliminary
DATE: April 12, 2007
NOTE: This specification is subject to change without prior notice.
Specification
of
DVD-RAM/R/RW/+R/+RW
& CD-R/RW Drive
(DVD Super MULTI Drive)
(Tentative)
Model SW-9576-CXX
Customer
Distributor
Panasonic Industrial Company
Section: Matsuyama Development Group
Name: Tadashi Masuda
Signature:
Date:
Apr. 23, 2007
Note
Preliminary
(Document No.: SP9576C-P02)
Panasonic Communications Co., Ltd.
Page 1 of 23
CONTENTS
1.0 General
-------------------------------
Page 3
------
Page 5
2.0 Performance and Functional Specification
2.1 Key feature
2.1.1 Data Format
2.1.2 Error Correction
2.1.3 IDE Interface
2.1.4 Transfer Rate
2.1.5 Disc Access Indicator
2.1.6 Data Buffer
2.1.7 Load Eject Mechanism
2.1.8 CD-DA Audio on I/F Feature
2.1.9 CD-R/RW Media
2.1.10 Writing Method
2.2 Performance
2.2.1 Data/Audio Capacity
2.2.2 Transfer Rate (Burst Rate)
2.2.3 Access Time
2.2.4 Spin Up and Spin Down Time
--------------------------3.0 Environment
3.1 Temperature
3.2 Humidity
3.3 Vibration
3.3.1 Operating
3.3.2 Non-Operating
3.4 Shock
3.4.1 Operating
3.4.2 Non-Operating
3.5 Acoustic Noise
PCC
SP9576C-P02:
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 11
Page 2 of 23
4.0 Power Requirements
4.1 Source Voltage
4.2 Current
----------------------
Page 13
--------------5.0 Reliability and Serviceability
5.1 Uncorrectable Error Rates
5.2 Seek Error Rate
5.3 Design Life
5.4 Mean Time Between Failures (MTBF)
5.5 Mean Time To Repair (MTTR)
Page 14
-----------------6.0 Mechanical Specification
6.1 Drive Unit
6.1.1 Outer Dimensions
6.1.2 Weight
6.1.3 Mounting Orientation
6.1.4 Load/Eject Mechanism
6.1.5 Color
6.2 Connector
6.2.1 Power Connector
6.2.2 IDE Connector
6.2.3 Master/Slave Jumper
Page 15
---------------7.0 Agency/Safety Certifications
7.1 Safety
7.2 Electromagnetic Compatibility (EMC)
7.3 Laser Safety
Page 18
------------------
Page 19
8.0 IDE Interface Description
8.1 Interface signals
8.2 DC Characteristics
-----------------------9.0 IDE Commands
9.1 IDE ATA (Task File) Commands
9.2 IDE ATAPI Commands
Appendix. Mechanical Drawing (SW-9576-CXX)
PCC
SP9576C-P02:
---------
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 20
Page 23
Page 3 of 23
1.0 General
This document describes the information on the PCC SW-9576-CXX, DVD-RAM/R/RW,
+R/+RW and CD-R/RW drive with ATA Packet Interface.
The SW-9576-CXX can read the following types of disc:
CD:
CD-Audio
CD-ROM (mode 1 and mode 2)
CD-ROM XA (mode 2, form 1 and form 2)
CD-I (mode 2, form 1 and form 2)
CD-I Ready
CD-I Bridge
CD-R
CD-RW
Photo CD
Video CD
Enhanced Music CD
CD-TEXT
DVD:
DVD-5
DVD-9
DVD-10
DVD-R (3.95G/4.7G)
DVD-R DL
DVD-RAM (4.7G)
DVD-RW
+R
+R DL
+RW
The SW-9576-CXX can read in CAV mode for CD and DVD discs, and can write in CLV or
Z-CLV or CAV mode for DVD-RAM/R/RW, +R/+RW and CD-R/RW discs.
The SW-9576-CXX supports the following DVD/CD discs and writing methods.
DVD:
DVD-RAM
DVD-R 4.7GB for General (Ver.2.0)
DVD-R DL
DVD-RW (Ver.1.1 / 1.2)
+R/+R DL
+RW
CD:
CD-R, CD-RW
PCC
SP9576C-P02:
Random Access
Disc at Once, Incremental
Disc at Once, Incremental
Disc at Once, Incremental,
& Restricted Overwrite
Sequential Recording
Multi-Session
Random Write
Disc at Once
Session at Once
Track at Once
Fixed/Variable packet writing
Multi-session
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 4 of 23
The MPEG data is not decoded.
CD-DA data can be transferred via IDE I/F.
The outline of mechanical dimensions of the drive SW-9576-CXX is as follows.
H: 41.3 mm [typ.] (excluding Front Panel)
W: 146 mm [typ.] (excluding Front Panel)
D: 196 mm [typ.] (excluding Front Panel)
This drive is a tray type drive that accepts to load either 120 mm disc or 80 mm disc for
reading and writing. When the 120 mm disc is mounted vertical orientation, certainly attach
the disc to the rib on the tray. The 80 mm disc should be loaded on the drive that is mounted
horizontal orientation.
This drive is designed only for discs, which are marked by CD logo, CD-R logo, CD-RW
logo and DVD logo. Don’t insert any other abnormal shaped discs (These discs will not be
able to be loaded or ejected.).
PCC
SP9576C-P02:
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 5 of 23
2.0 Performance and Functional Specification
2.1 Key feature
2.1.1 Data Format
The DVD-RAM/R/RW, +R/+RW and CD-R/RW drive (SW-9576-CXX) is capable of
reading and writing, decoding and encoding Error Correction Code in real time and
transferring over the IDE interface, the industry standard data format for compact disc in the
following formats:
1. CD-DA as defined by " Red Book".
2. CD-ROM data in Mode 1 & Mode 2 as defined by "Yellow Book".
3. CD-ROM XA data Form 1 & Form 2.
4. Disc containing combinations of Formats 1, 2, and 3 above in accordance to the
current ISO and CD-ROM XA standards.
5. CD-I as defined by "Green Book", CD-I Bridge & CD-I Ready.
6. Single & multiple session discs as defined by "Orange Book Part2/3".
7. CD Rewritable discs as defined by “Orange Book Part3”.
8. Video CD as defined by "White Book".
9. Enhanced Music CD as defined by "Blue Book".
10. CD-TEXT mode.
11. DVD Disc as defined by "DVD Specification for Read-only Disc Ver. 1.0".
12. DVD-R Disc as defined by “DVD Specification for Recordable Disc Ver. 2.1”.
13. DVD-R DL Disc as defined by “DVD Specification for Recordable Disc for Dual
layer Ver. 3.0”.
14. DVD-RW Disc as defined by “DVD Specification for Rerecordable Disc Ver.1.2”.
15. DVD-RAM Disc as defined by “DVD Specification for Rewritable Disc Ver. 2.1”.
16. +R Disc as defined by ”DVD+R 4.7Gbytes Basic Format Specifications Version 1.3”.
17. +RW Disc as defined by ”DVD+RW 4.7Gbytes Basic Format Specifications
Version 1.3”.
18. +R DL Disc as defined by ” DVD+R DL 8.5Gbytes Basic Format Specifications
Version 1.0”.
2.1.2 Error Correction
The SW-9576-CXX is capable of performing real time error correction on the industry
standard data format for a disc in the following formats:
1. CD-DA standard Red Book audio.
2. CD-ROM data in Mode 1.
3. CD-ROM data in Mode 2.
4. CD-ROM data in Mode 2, Form 1.
5. CD-ROM data in Mode 2, Form 2.
6. Disc containing combinations of Formats 1, 2, 3, 4 and 5 above in accordance to
current ISO and CD-ROM XA standards.
7. DVD-RAM/ROM/R/RW standards.
8. +R, +RW standards.
PCC
SP9576C-P02:
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 6 of 23
2.1.3 IDE Interface
The SW-9576-CXX has an IDE interface that conforms to the ATA Packet Interface for
DVD-ROM/RAM/R/RW, +R/+RW and CD-ROM/R/RW.
The IDE interface shall also comply with ANSI ATA/ATAPI-7.
2.1.4 Transfer Rate
DVD-ROM
(single layer)
DVD-ROM
(dual layer)
DVD-R (4.7G)
DVD-R DL
DVD-R (3.95G)
DVD-RW
DVD-RAM (4.7G)
+R
+R DL
+RW
CD-ROM (*1)
CD-R (*1)
CD-RW (*1)
(Ultra speed RW)
DVD-Video
(with CSS)
CD-DA
Read
Write
6.6X to 16X CAV
9 141 KB/s to 22 160 KB/s
3.3X to 8X CAV
4 570 KB/s to 11 080 KB/s
6.6X to 16X CAV
9 141 KB/s to 22 160 KB/s
3.3X to 8X CAV
4 570 KB/s to 11 080 KB/s
6.6X to 16X CAV
9 141 KB/s to 22 160 KB/s
3.3X to 8X CAV
4 570 KB/s to 11 080 KB/s
5X Z-CLV
6 925 KB/s
6.6X to 16X CAV
9 141 KB/s to 22 160 KB/s
3.3X to 8X CAV
4 570 KB/s to 11 080 KB/s
3.3X to 8X CAV
4 570 KB/s to 11 080 KB/s
17.2X to 40X CAV
2 580 KB/s to 6 000 KB/s
17.2X to 40X CAV
2 580 KB/s to 6 000 KB/s
10.3X to 24 CAV
1 545 KB/s to 3 600 KB/s
6.6X to 16X CAV
9 141KB/s to 22 160KMB/s
4X CLV
5 540KB/s
6X CLV
8 310KB/s
5X Z-CLV
6 925 KB/s
6.6X to 16X CAV
9 141KB/s to 22 160KMB/s
4X CLV
5 540KB/s
6X to 8X Z-CLV
8 310KB/s to 11 080KMB/s
16X to 40X Z-CLV
2 400KB/s to 6 000 KB/s
16X to 24X Z-CLV
2 400KB/s to 3 600 KB/s
6X CAV
-
24X CAV
-
Note (*1): in case of mode 1 form 2 data
PCC
SP9576C-P02:
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 7 of 23
2.1.5 Disc Access Indicator
The SW-9576-CXX has a LED on the Front Panel and it indicates "BUSY".
2.1.6 Data Buffer
The SW-9576-CXX has a data buffer that is implemented as a ring buffer.
This buffer has a size of 2 Mbyte.
2.1.7 Load Eject Mechanism
The SW-9576-CXX has a motor powered tray to load and unload the disc. The tray can be
operated by the Eject button or START/STOP UNIT command through the IDE interface.
And the drive has a 1.8 mm diameter pinhole for the emergency tray eject.
2.1.8 CD-DA Audio on I/F Feature
CD-DA digital data is available through the IDE interface and an error flag can be
transferred with CD-DA data. The CD-DA digital data has all normal CD-DA error correction,
interpolation and de-emphasis performed prior to being transmitted on the IDE bus. In case of
writing, on the other hand, the CD-DA digital data, which is transmitted on IDE bus, is
encoded by normal CD-DA error correction and then added Sub-code data according to
circumstances prior to being written on the CD-R/RW media.
2.1.9 CD-R/RW media
All CD-R media must conform to Compact Disc Recordable (Orange Book Part 2) provided
by Philips Electronics N.V.
All CD-RW media must conform to Compact Disc ReWritable (Orange Book Part 3 and Part
3 Volume 2) provided by Royal Philips Electronics.
PCC
SP9576C-P02:
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 8 of 23
2.1.10 Writing Method
The SW-9576-CXX supports following Writing Method;
CD:
Disc at Once
Session at Once
Track at Once
Multi-Session
Fixed/Variable Packet Writing
DVD:
DVD-RAM
DVD-R 4.7GB for General (Ver.2.0)
DVD-R DL
DVD-RW (Ver.1.1 / 1.2)
+R/+R DL
+RW
Random Access
Disc at Once, Incremental
Disc at Once, Incremental
Disc at Once, Incremental,
& Restricted Overwrite
Sequential Recording
Multi-Session
Random Write
2.2 Performance
2.2.1 Data/Audio Capacity
CD:
Data Capacity
703 Mbyte (Mode 1)
797 Mbyte (Mode 2)
Playing Time
79 min 58 s
Note: Data Capacity and Playing Time depends on Linear velocity and Track pitch of the disc.
Maximum Data capacity for writing is depend on each CD-R/RW media vender and
Data format.
DVD: Data Capacity
DVD-RAM
DVD-R
DVD-R DL
DVD-RW
Single Layer
Dual Layer
Single Layer Double Side
+R
+R DL
+RW
4.7 Gbytes
3.95 Gbytes
4.7 Gbytes
8.54 Gbytes
4.7 Gbytes
4.7 Gbytes
8.5 Gbytes
9.4 Gbytes
4.7 Gbytes
8.5 Gbytes
4.7 Gbytes
Note: Data Capacity and Playing Time are dependent on linear velocity and Track
pitch of the disc.
PCC
SP9576C-P02:
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 9 of 23
2.2.2 Transfer Rate (Burst Rate)
PIO
Multiword DMA
Ultra DMA
Mode4 (16.67 Mbyte/s)
Mode2 (16.67 Mbyte/s)
Mode2 (33.33 Mbyte/s)
Mode4 (66.67 Mbyte/s)
2.2.3 Access Time
CD-ROM: (Disc: MNSU-005)
Random (*1)
Typical
200 ms
Average Max. 300 ms
Typical
340 ms
Average Max. 510 ms
Full Stroke (*2)
Notes: (*1) Average of Data read over the whole area from 00 min 02 s 00 block to 59 min 58
s 74 block, more than 2 000 times including latency and layered error correction
time.
(*2) From 00 min 02 s 00 block to 59 min 58 s 74 block more than 2 000 times
including latency and layered error correction time.
DVD-5: (Disc: MKE-D551)
Random (*3)
Typical
170 ms
Average Max. 260 ms
Typical
320 ms
Average Max. 480 ms
Full Stroke (*4)
Notes: (*3) Average of Data read over the whole area from starting data recorded area (LBA:
0) to maximum data recorded area (LBA: 23197F), more than 2 000 times
including latency and layered error correction time.
(*4) From starting data recorded area (LBA: 0) to maximum data recorded area (LBA:
23197F), more than 2 000 times including latency and layered error correction
time.
DVD-RAM (4.7 G):
Random (*7)
Full Stroke (*8)
Typical
Average max.
Typical
Average max.
240 ms
360 ms
1 130 ms
2 500 ms
Notes: (*7) Average of Data read over the whole area from starting data recorded area (LBA:
0) to maximum data recorded area (LBA: 22211F), more than 2 000 times
including latency and layered error correction time.
(*8) From starting data recorded area (LBA: 0) to maximum data recorded area (LBA:
22211F), more than 2 000 times including latency and layered error correction
time.
PCC
SP9576C-P02:
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 10 of 23
2.2.4 Spin Up and Spin Down Time
Spin Up Time
From loading to ready
(Not include tray close time.)
From standby mode to ready
Spin Down Time
Test Discs:
Typical
Max.
15 s (CD, DVD-5)
20 s (CD, DVD-5)
Typical
Max.
4s
7s
Typical
Max.
4s
6s
CD: MNSU-005
DVD-5: MKE-D551
PCC
SP9576C-P02:
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 11 of 23
3.0 Environment
3.1 Temperature (Ventilation 0.13 m3/min ∼ 0.19 m3/min)
+5 °C ~ +45 °C
-30 °C ∼ + 60 °C
Operating
Non-Operating
3.2 Humidity
Operating (non-condensing)
Non-Operating (non-condensing)
10%[RH] ∼ 80 %[RH]
(max. wet bulb temp. is 29 °C)
5 %[RH] ∼ 90 %[RH]
3.3 Vibration
3.3.1 Operating
The SW-9576-CXX meet the uncorrectable error rate specification (described in section 6.1)
with continuous sine wave vibration at following frequency range, magnitude and direction
specified below;
5 Hz ∼ 500 Hz
(Sweep rate is 1 octave/min.)
Read: 1.96 m/s2 {0.2 G} [peak]
(Along X, Y and Z axis)
Write: 0.98 m/s2 {0.1 G} [peak]
(Along X, Y and Z axis)
3.3.2 Non-Operating
The SW-9576-CXX will withstand continuous sine wave vibration at a frequency range,
magnitude and direction specified below.
5Hz ∼ 500 Hz
(Sweep rate is 1 octave/min.)
PCC
SP9576C-P02:
9.8 m/s2 {1.0 G} [peak]
(Along X, Y and Z axis)
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 12 of 23
3.4 Shock
3.4.1 Operating
The SW-9576-CXX meet the uncorrectable error rate specification (described in section 5.1
exclude CD-DA) with a half sine wave shock at a magnitude, interval and direction specified
below.
Read: 49.0 m/s2 {5.0 G} [peak]
(Along X, Y and Z axis)
11 ms half sine wave
(Input interval is 10 s.)
Write: 4.9 m/s2 {0.5 G} [peak]
(Along X, Y and Z axis)
3.4.2 Non-Operating
The SW-9576-CXX will withstand shock with a half sine wave shape at magnitude, interval
and direction specified below.
490 m/s2 {50 G} [peak]
11 ms half sine wave
3.5 Acoustic Noise
Microphone locates 1m above the drive.
Access mode
PCC
50 dB [max.] (A filter)
SP9576C-P02:
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 13 of 23
4.0 Power Requirements
4.1 Source Voltage
Voltage
Tolerance
Ripple
+5 V [DC]
±0.25 V
100 mV[p-p]
+12 V [DC]
±1.2 V
200 mV[p-p]
4.2 Current
Hold Track
Read
Write
Seeking
Spin Up
Standby
Sleep
+5 V [DC]
max. [typ.] mA (*1)
CD
DVD
1 100 (850) 1 200 (850)
1 100 (850) 1 200 (850)
1 200 (950) 1 500 (1 100)
1 500 (850) 1 500 (750)
1 700 (700) 1 700 (700)
- (100)
- (100)
- ( 65)
- ( 65)
Used Test Disc for Measurement
+12 V [DC]
max. [typ.] mA (*1)
CD
DVD
1 400 (750) 1 200 (800)
1 400 (750) 1 200 (800)
1 500 (650) 1 500 (800)
1 500 (700) 1 500 (450)
2 000 (400) 2 000 (400)
- (50)
- (50)
- (50)
- (50)
CD: Read MNSU-005
DVD: Read MKE-D551
Notes (*1): max. ; Pulse width = 2 ms or more
PCC
SP9576C-P02:
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 14 of 23
5.0 Reliability and Serviceability
5.1 Uncorrectable Error Rates
The SW-9576-CXX will meet the following error rates when reading from a following
conditions disc
CD that has a maximum block error rate of 3 in 10 E2
Mode 1 and Mode 2 Form 1
Less than 1 in 10 E12
Mode 2 Form 2 and CD Audio
Less than 1 in 10 E9
DVD that has a maximum 280 PI errors in 8 ECC blocks
Less than 1 in 10 E12
5.2 Seek Error Rate
Less than 1 in 10 E6
Seek Error Rate
5.3 Design Life
Traverse mechanism
2 000 000 seek or more
(full stroke) (*1)
30 000 cycle or more
Tray loading mechanism
(*1) The 3 s of time interval between each seeks should be taken.
5.4 Mean Time Between Failures (MTBF)
MTBF is defined as following condition.
Read and Access duty is 10 % of POH.
MTBF
50 000 POH
5.5 Mean Time To Repair (MTTR)
MTTR
30 min
PCC
SP9576C-P02:
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 15 of 23
6.0 Mechanical Specification
6.1 Drive Unit
6.1.1 Outer Dimensions
Height of drive
Width of drive
Depth of drive
41.3 mm [typ.] (excluding Front Panel)
146.0 mm [typ.] (excluding Front Panel)
196.0 mm [typ.] (excluding Front Panel)
6.1.2 Weight
Weight of drive
1.16 kg [TBD]
6.1.3 Mounting Orientation
Horizontal
This drive will be capable of operation when mounted within ±5 º of the (left to right)
horizontal position. In addition, the drive will be capable of operating with up to ±5 º tilts
applied to the front to back dimension.
Vertical
This drive will be capable of operating with up to ±5 º tilts applied to the front to back
dimension.
Drive upper frames is facing the gravity direction: less than 0 º
Drive lower frames is facing the gravity direction: less than 5 º
6.1.4 Load/Eject Mechanism
Tray Insertion Force
Emergency Eject Force
8.0 N [typ.]
11.0 N [typ.]
Tray Open Time
1.0 s [typ.]
3.0 s [max.]
Tray Close Time
1.0 s [typ.]
3.0 s [max.]
PCC
SP9576C-P02:
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 16 of 23
6.1.5 Color
Tray
Bezel
Tray Escutcheon
Eject Button
Ivory B-W-4
Ivory B-W-4
Ivory B-W-4
Ivory B-W-4
6.2 Connector
The SW-9576-CXX has a combined Power/Jumper/IDE Interface connector. It consists of a
4-pin Power Connector, a 40-pin Interface Connector, a 6-pin Master/Slave Jumper, a 4-pin
Not Used Connector and a 2-pin Not Used Connector as shown below.
Figure 1 - Combined Power/IDE/Jumper Connector
6.2.1 Power Connector
The power connector is a four-conductor male plug. The pin assignments are shown Figure
2.
4 3 2 1
1
2
3
4
+12 V
GND
GND
+5 V
Figure 2 - Power Connector
Recommended part numbers for the mating connector to 18 AWG cable are shown below.
Connector (4 pin):
Contacts (loose piece):
Contacts (strip):
PCC
SP9576C-P02:
AMP 1-480424-0 or equivalent.
AMP 60619-4 or equivalent.
AMP 61117-4 or equivalent.
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 17 of 23
6.2.2 IDE Connector
The I/O connector is a 40-pin connector as shown Figure 3 with pin assignments as shown
in Table 1. The connector is keyed to prevent the possibility of installing it upside down. A
key is provided by the removal of pin 20.
39
1
40
2
Figure 3 - IDE Connector
Recommended part numbers for the mating connector are shown below.
Connector (40 pin)
Strain relief
Flat cable (stranded 28 AWG)
Flat cable (stranded 28 AWG)
3M 3417-7000 or equivalent
3M 3448-2040 or equivalent
3M 3365-40 or equivalent
3M 3517-40 (shielded) or equivalent
6.2.3 Master/Slave Jumper
The drive has a 6-pin jumper to enable CSEL, Master and Slave modes.
The default position is Master.
3 21
1 Master
2 Slave
3 Cable Select
Figure 4 - Jumper
PCC
SP9576C-P02:
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 18 of 23
7.0 Agency/Safety Certifications
7.1 Safety
UL/cUL (UL60950-1)
CSA 22.2 No.60950-1
TUV (EN60950-1)
SEMKO (EN60950-1)
CB Scheme IEC60950-1
7.2 Electromagnetic Compatibility (EMC)
CE Marking (EMC Directive 89/336/EEC)
EN55022 (CISPR Pub. 22)
EN55024
EN61000-4-2
Test-spec.: 4 kV for contact discharge
8 kV for air discharge
EN61000-4-3
Test Spec.: 3 V/m
(Modulation: AM80 % 1 kHz)
EN61000-4-4
Test-Spec.: AC 1 kV
DC 0.5 kV
I/F 0.5 kV
(Min. 1min)
EN61000-4-5
Test-Spec.: AC line to line 1 kV
line to ground 2 kV
(2 time / minute)
EN61000-4-6
Test-Spec.: 3 V [rms]
(Modulation: AM80 % 1 kHz)
EN61000-4-8
Test-Spec.: 1 A/m
(1 min)
EN61000-4-11
Test-Spec.: Min. 10 s
(3 times)
7.3 Laser Safety
21 CFR Subchapter J as a Class 1 laser device
IEC 60825-1/EN60825-1
PCC
SP9576C-P02:
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 19 of 23
8.0 IDE Interface Description
8.1 Interface signals
Signal
RESETGROUND
DD7
DD8
DD6
DD9
DD5
DD10
DD4
DD11
DD3
DD12
DD2
DD13
DD1
DD14
DD0
DD15
GROUND
(KEYPIN)
DMARQ
GROUND
DIOWGROUND
DIORGROUND
IORDY
SPSYNC:CSEL
DMACKGROUND
INTRQ
IOCS16DA1
PDIAGDA0
DA2
CS0CS1DASP
GROUND
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
I/O
I
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
I
I
O
I
O
O
I
I/O
I
I
I
I
I/O
-
Drive reset
Drive data bus - bit 7
Drive data bus - bit 8
Drive data bus - bit 6
Drive data bus - bit 9
Drive data bus - bit 5
Drive data bus - bit 10
Drive data bus - bit 4
Drive data bus - bit 11
Drive data bus - bit 3
Drive data bus - bit 12
Drive data bus - bit 2
Drive data bus - bit 13
Drive data bus - bit 1
Drive data bus - bit 14
Drive data bus - bit 0
Drive data bus - bit 15
DMA Request
Drive I/O write
Drive I/O read
I/O channel ready
DMA acknowledge
Drive interrupt
Drive 16-bit I/O
Drive address bus bit 1
Passed diagnostics
Drive address bus bit 0
Drive address bus bit 2
Drive chip select 0
Drive chip select 1
Drive active/Drive 1 present
Table 1 - interface signal description
PCC
SP9576C-P02:
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 20 of 23
8.2 DC Characteristics
Signal Level
Parameter
Input Voltage
Input Current Sink
Hysterisis
Output Voltage
Output Current
Low
High
0.0 V [DC] ∼ 0.8 V [DC] 2.0 V [DC] ∼ 5.25 V [DC]
4 mA [min.]
0.2 V [DC] [min.]
0.0 V [DC] ∼ 0.5 V [DC] 2.4 V [DC] ∼ 5.25 V [DC]
-0.4 mA [min.]
Note: Cable capacitive loading is 40 pF max.
Table 2 - IDE Interface DC characteristics
9.0 IDE Commands
9.1 IDE ATA (Task File) Commands
Command
ATAPI SOFT RESET
CHECK POWER MODE
EXECUTE DRIVE DIAGNOSTICS
IDLE IMMEDIATE
NOP
PACKET COMMAND
ATAPI IDENTIFY DEVICE
SET FEATURES
SLEEP
STANDBY IMMEDIATE
Op. Code
08h
E5h
90h
E1h
00h
A0h
A1h
EFh
E6h
E0h
Table 3 - ATA Commands
PCC
SP9576C-P02:
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 21 of 23
9.2 IDE ATAPI Commands
Command Description
BLANK
CLOSE TRACK/RZONE/SESSION/BORDER
FORMAT UNIT
GET CONFIGURATION
GET EVENT STATUS NOTIFICATION
GET PERFORMANCE
INQUIRY
MECHANISM STATUS
MODE SELECT (6)
MODE SELECT (10)
MODE SENSE (6)
MODE SENSE (10)
PAUSE/RESUME
PLAY AUDIO (10)
PLAY AUDIO (12)
PLAY AUDIO MSF
PREVENT/ALLOW MEDIUM REMOVAL
READ (6)
READ (10)
READ (12)
READ BUFFER
READ BUFFER CAPACITY
READ CD/DVD CAPACITY
READ CD
READ CD MSF
READ DEFECT DATA
READ DISC INFORMATION
READ DVD STRUCTURE
READ FORMATTED CAPACITY
READ HEADER
READ SUB-CHANNEL
READ TOC/PMA/ATIP
READ TRACK/RZONE INFORMATION
REPAIR RZONE
REPORT KEY
REQUEST SENSE
REZERO UNIT
RESERVE TRACK/RZONE
SCAN
SEEK (6)
SEEK (10)
Op. Code
A1h
5Bh
04h
46h
4Ah
Ach
12h
BDh
15h
55h
1Ah
5Ah
4Bh
45h
A5h
47h
1Eh
08h
28h
A8h
3Ch
5Ch
25h
BEh
B9h
37h
51h
ADh
23h
44h
42h
43h
52h
58h
A4h
03h
01h
53h
BAh
0Bh
2Bh
Table 4 - ATAPI Commands (1/2)
PCC
SP9576C-P02:
Product Specification of SW-9576-CXX
Apr. 12, 2007
Page 22 of 23
Command Description
SEND CUE SHEET
SEND DVD STRUCTURE
SEND KEY
SEND OPC INFORMATION
SET CD SPEED
SET READ AHEAD
SET STREAMING
START STOP UNIT
STOP PLAY/SCAN
SYNCHRONIZE CACHE (FLUSH)
TEST UNIT READY
VERIFY (10)
VERIFY (12)
WRITE (6)
WRITE (10)
WRITE (12)
WRITE AND VERIFY (10)
WRITE AND VERIFY (12)
WRITE BUFFER
Op. Code
5Dh
BFh
A3h
54h
BBh
A7h
B6h
1Bh
4Eh
35h
00h
2Fh
AFh
0Ah
2Ah
AAh
2Eh
AEh
3Bh
Table4 - ATAPI Commands (2/2)
PCC
SP9576C-P02:
Product Specification of SW-9576-CXX
Apr. 12, 2007
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising