TPC AIC 5855, AIC 5899, AIC 5888, AIC 5111, AIC 5705, AIC 5905, AIC 5925, AIC 5920, AIC 5815, AIC 5835, AIC 5900, AIC 5901 Intraoral Camera User manual

TPC Advance CAM
Intraoral Camera Systems
Operation and Users Manual
Clarity
Versatility
Portability
Г
Models Covered in this manual are as follows
AIC 5855, 5899, 5888, 5111, 5705, 5905, 5925, 5920, 5815, 5835, 5900, 5901
REV. 1-1-13
Micro SD Camera AIC 5855+5111+5901
Attaching Power Pack
To connect the power pack, align the two fittings
together. They will only connect one way. Once aligned
press into place. To remove the power pack pull back on
the lock ring to release it. Then pull the power pack out
of the camera while holding the lock ring in place. Power Pack
п Пао —тещщаннниь
— —"; =
——
ag D ñ
3
Attaching LCD Monitor
2.5” LCD monitor
To attach the on board LCD monitor
slide the male end of the connection
to the body of the camera. Pull straight
out to remove it.
ев NN.
TPC
Memory Card installation
Press card into camera gently
Insert only as shown in photo
Once it clicks it will be locked in
place. Press again to remove.
1GB micro SD
Card Exp to 16GB
— ный
— ==
=
a =
»
SR
A;
Corded Setup
Connect the 5.0 VDC power supply (included)
for continuous uninterrupted imaging.
Connect the (included) composite video cable to an
additional display device TV or LCD monitor.
Micro SD Camera Operating Instructions
Charging the power pack
Use the provided charger to recharge the
battery on your power pack. Once connected
the light on the charger should be RED indicat-
ing that the battery is charging. Once it reaches
a full charge the light will turn green.
Turning the camera on.
With power pack turned on or the cord connected to
the camera press the freeze button to activate the system.
Once the system is active you will see the letters TPC
flash on the screen for about 5 seconds.
Once this is completed you will see a live image.
Function of controls
Press the Freeze button to Freeze an image on the screen.
Press the Freeze button again to return to a live image.
Press the Save button to capture an image onto the memory
card. This can be performed when the image is live or frozen.
Press “up” to review stored images acending.
Press “Down” to review stored images decending.
Press “Delete” to delete any image that you are
viewing while in memory.
mu
u
м
Download images to PC
Remove memory card X
and place it in the micro 3 — A
SD to USB adaptor. Connect
to USB port on computer to review
saved images.
AIC5899 Direct USB Camera
Kvosourapy ! UP
a
Mm
©
1. Don't connect the USB device before running CD!
2. Place the included disc in your CD tray and run it.
3. When the auto run screen appears run each step.
You may skip the TPC softimage installation if you
are using your own management software.
4. Once the camera driver's are installed you will
need to restart your computer.
5. After your computer reboots you may connect
your camera to the computer. We recommend that
you use USB 2.0 port.
6. Generally Windows 7 and Vista will install these
drivers automatically. Windows XP may require
additional steps. If the found new hardware wizard
appears Follow the instructions within the program
to complete the driver installation.
7. Additional information and instructions on the
TPC software and USB driver installation can be
found on the software disc.
Optional AIC 5111
2.5” LCD monitor
AIC 5888+ 705+ 5900 Wireless USB
Selecting wireless channel
To select a wirless channel flip the
corrsponding switch towards the desired
channel 1, 2, 3 or 4. Only one channel can
be turned on at any time.
Installing USB Drivers
Refer to the direct USB
camera installation for
installing drivers.
Connecting USB
Connect AIC 705 to USB 2.0
port on your computer.
Powering on your camera
Slide Switch down to turn on the
transmitter. When the transmitter is
powered on you will see the leds
illuminate on the top of the transmit-
ter. Slide back up to power it off. Charging your Transmitter
To charge the power pack
use the provided power supply.
Connect it the DC IN
charging port . When the
power pack is charging the
LED on the charger will turn
red. Once the battery is
charged the light will turn
Choice: Press Choice green indicating a full charge.
button to select different
channels on the tranmit-
ter. By default the trans-
mitter will turn to CH 1
when powering on.
Corded Camera System AIC5888+5905 / 5925
Connecting your Camera
To connect the camera cable, align the two
fittings together. They will only connect
one way. Once aligned press into place. To
remove pull back on the lock ring to
release it. Then pull the cable out of the
camera while holding the lock ring in
place.
Connecting your Docking Station
On / Off Switch. Turns power to docking station ON and Off
DC 5V: Input power jack. Connect included power supply.
Freeze: Connects to optional foot control to freeze images.
USB Out: Connects to USB port on computer for PC setup.
Video Out: Connects to analog input on display device.
VGA Out: Connets to VGA input on display device. PC monitor.
IR: Connect an external IR sensor for use with remote control.
Camera Controls
Press the Freeze button to Freeze an image on the screen.
Press the Freeze button again to save and return to a live image.
Press the full / quad button to change from full screen to quad.
Press “up” to review stored images acending.
Press “Down” to review stored images decending.
Press the “Delete” to delete any image that you are
viewing while in memory. |
Optional AIC 5111
2.5” LCD monitor
USB Driver Installation
1. Don't connect the USB device before running CD!
2. Place the included disc in your CD tray and run it.
3. When the auto run screen appears run each step. You may
skip the TPC softimage installation if you are using your own
management software.
4, Once the camera driver's are installed you will need to restart
your computer.
5. After your computer reboots you may connect your camera to
the computer. We recommend that you use USB 2.0 port.
6. Generally Windows 7 and Vista will install these drivers auto-
matically. Windows XP may require additional steps. If the found
new hardware wizard appears Follow the instructions within the
program to complete the driver installation.
7. Additional information and instructions on the TPC software
and USB driver installation can be found on the software disc.
Docking Station Remote Control
Full / Quad Button: Choose to capture image in full screen or capture 4
images (quad).
F/M: Press button to capture image on monitor
Delete Button: Press shaded quad (1,2,3 or 4) to “delete” image from that
specific quad. Press “Freeze Button” to re-capture image for specific quad.
Zoom Button: Press shaded quad (1,2,3 or 4) to “zoom” image from that
specific quad. Press again to return to normal size.
Delete Single Image: This function will delete the single image that is
displayed on the screen.
Delete All Memory: This will delete all images stored in memory. When
pressed you will be asked “ARE YOU SURE?" To proceed, press the “delete all
memory” button again and this will delete all images stored in memory.
Previous Image and Next Image: Allows you to scroll through the images
stored in the camera memory.
Clear: When looking at an image in memory press
the clear button to delete it out of the memory bank.
AIC5888+5815/5835+5900 wireless System
Selecting wireless channel
To select a wirless channel flip the
corrsponding switch towards the desired
channel 1, 2, 3 or 4. Only one channel can
be turned on at any time. preset to CH 1
Selecting PAL or NTSC Mode
P and N: Set to P for use with PAL camera.
Bottom Of Docking station
Set to N for use with NTSC camera.
WL and W: Set to WL for wireless mode. Set
to W for wired mode. To check which mode
you should use, look at the last two letters
of your serial number on your camera.
NT= NTSC PA= PAL
Connecting your docking station.
On / Off Switch. Turns power to docking station ON and Off
DC 5V: Input power jack. Connect included power supply.
Freeze: Connects to optional foot control to freeze images.
USB Out: Connects to USB port on computer for PC setup.
Video Out: Connects to analog input on display device.
VGA Out: Connets to VGA input on display device. PC monitor.
IR: Connect an external IR sensor for use with remote control.
Power On / Off
Power Adaptor 5V USB PC Connection Video / VGA
Refer to driver disc for
installation information
AIC 5888+5815+5900 Wireless Camera
Charging your Transmitter
To charge the power pack use the provided
power supply. Connect it the DC IN charging
port . When the power pack is charging theLED
on the charger will turn red. Once the battery is
charged the light will turn green indicating a full
charge.
Connecting your Transmitter
To connect the transmitter, align the two fittings
together. They will only connect one way. Once aligned
press into place. To remove the transmitter pull back on
the lock ring to release it. Then pull the transmitter out of
the camera while holding the lock ring in place.
( TPC .—
Powering on your camera
Slide Switch down to turn on the transmitter. When the transmitter
is powered on you will see the leds illuminate on the top of the
transmitter. Now press the freze button to activate the 6 LED's and
CCD. Reverse switch position to power off.
Optional AIC 5111
2.5” LCD monitor
N
N
Wireless Mode Camera Controls
Press the Freeze button to Freeze an image on the screen.
Press the Freeze button again to save and return to a live image.
Press the full / quad to change the screen from full screen to quad.
Note: While using the camrea in wirelessmode you may only use
the remote control to review and delete images. Refer to page 6
for remote control operating instructions.
Camera Mounted 2.5" LCD Display
OC 2X
Rotation: Adjusts the screen orentation
Menu: Access the on screen display options
Up: Make adjustments up
Down: Make adjustments down
AIC 500 Intraoral Camera Sheath
Hold sheath and Y \
insert the camera 7 ||
between the white Е
tab and the paper A4
with the optical 74 +
| ~Y #/
side facing VA —
the paper.
®
Peel back the
protective top
cover,
Gently slide the camera until the
camera head reaches the tip of
the sheath. DO NOT FORCE.
Peel away the paper
backing.
Idenification of Components
a =
1 GB Mini SD Cam а МС
Memory Card Power Supply Char
AIC5901 arger
IR Sensor
AIC-IR
©
Camera Cable USB Cable
AIC5888
SD Camera 5VDC ,
Cable Power Cable — 2-2” LCD Monitor
AIC5111
me. - =>
==
Transmitter AjC5899-USB AIC 705
AIC5900 Camera Cable Wireless USB
[LI
qn
a"
a
AIC 905 8: 925 q
AIC 5815 8: 5835 AIC5920
Docking Stations Receiver
AIC 5855 Mini SD Camera
AIC 5899 Direct USB Camera
AIC 5888+5111+5900 Wireless Camera
Docking Station
Remote
Micro SD
Converter
Camera
BarriersAIC500
Composite
Video Cable
Warranty Information
Warranty: TPC warranties most camera components to be free from
defect for a 2 year period. Components not covered under warranty are
as follows: LED's are rated at 100,000 hours but not under warranty for
any period. Batteries are excluded from this warranty as well. This
warranty excludes negligence on behalf of the end user. Most camera
components can be repaired, if an item can't be repaired and it's under
warranty, TPC will replace the item. All shipping charges are to be pre
paid at the end user expense.
TPC Advanced Technology
18525 E. Gale Ave
City Of Industry, CA 91748
Tel: 800-560-8222
Fax: 626-810-4245
tpcdental.com
email support [email protected]
Name:
Address:
Telephonet
Product Serial Numbers
Camera
Wand
Docking
Staion
Transmitter
LCD
Monitor
Power Pack