STRIPPING CLEAVING INSPECTING CLEANING

STRIPPING CLEAVING INSPECTING CLEANING
HUBBELL PREMISE WIRING | Fiber Optics Tooling & Maintenance Product Guide
HUBBELL PREMISE WIRING | Fiber Optics Tooling & Maintenance Product Guide
Cable Preparation
Field Termination Kit
Cleaning Sticks
Cleaning Wipes
Crimp Tool
Kevlar® Cable Scissors
Termination Kit for SC/ST Style Connectors
Dual hex cavity: 0.178”/0.151”, flat crimp
0.052”, hex crimp 0.136”, hardened die
Description
Catalog No.
For cutting Kevlar®
reinforced cables up to
24-strand, non-armored
OFSCSRS
Includes:
• Heat-cure epoxy oven (110V)
• Tool pouch (OFTP02C)
• Fiber preparation tool
• Cable preparation tool
• Heat cure epoxy
• Anaerobic adhesive
• Anaerobic primer
• Polishing paper
• Polishing pad
• Canned air 10oz
• Safety glasses
• Wipes
• Syringes
• Needles
• Cure adapters
• Clips
Description
Catalog No.
Sticklers® CleanStixx™,
LC/MU/APC
Sticklers® CleanWipes™,
Cartridge
Field epoxy termination kit
OFTK03C
Includes: (1) 50 pack disposable cleaning sticks
Includes: (1) 4-slot box
Catalog No.
Description
Catalog No.
OFSTIX50LC
Box of 100 lint-free
sheets, 4 wipes/sheet
OFWIPES400
Description
Catalog No.
For SC/ST-style epoxy/
anaerobic or crimp style
connectors
OFCMT04
Kevlar is a registered trademark of E.I. du Pont de
Nemours and Co.
Fiber Cleavers
Fiber Strip Tools
Description
Universal 250/900µ, 2.0,
2.5, 3.0mm cable
Description
Catalog No.
OFSTRIP2
Catalog No.
Sticklers® CleanStixx™,
SC/ST/FC/APC
Sticklers® CleanWipes™,
Dispenser
Includes: (1) 50 pack disposable cleaning sticks
Includes: (1) roll of 90 sheets
Description
Catalog No.
Description
Catalog No.
SC/FC/APC 2.50mm
port cleaning sticks
OFSTIX50SC
Tube of 90 lint-free
sheets, multi-purpose
OFWIPES90
Multimode fiber only
OFCLV3
Description
SM or MM fiber, precision,
with case
OFCLV5
LC/MU/APC 1.25mm
port cleaning sticks
Scribing
Cleaning Kits
STRIPPING
Hand Scribe Tool
Includes: (1) tool and scribe guide
Description
Sapphire blade
Catalog No.
OFSCRIBE
Scribe Guide Fixture
6-pack
Description
Catalog No.
Suitable for SC, ST-style,
or LC connectors
OFSG
Use a precision strip tool sized
correctly to remove 900µm or 250µm
buffer coatings, and cable jackets up to
3mm in diameter.
•Strip buffer coatings in small increments with a firm,
steady motion to avoid breaking fiber.
•The tool should not break the glass fiber.
•Gently bend the fiber to check for nicks. A nicked
fiber will break easily.
•Clean the fiber with a wipe and cleaning fluid.
CLEAVING
INSPECTING
Always “clean and inspect before you
connect” using Hubbell cleaning products
and a 200x or 400x microscope.
A precision cleaved fiber has a flat
end with zero cleave angle and no
cracks, pits or edge fractures.
•Use a precision cleave tool for terminating prepolished mechanical splice connectors, which are
sensitive to cleave quality.
•For adhesive connectors, use a scribe fixture to
control cleaved fiber height for best polishing results.
•Cleaved separation is achieved by scoring and
applying tension to the fiber. Bending causes high
cleave angle and fractures.
CLEANING
•The polished fiber end face must be free of
contamination, residue, cracks, chips or scratches.
•Clean connector tips using Hubbell lint-free wipes
and optical grade fiber cleaning fluid.
•Clean fiber ports using 1.25mm cleaning sticks for
LC ports and 2.5mm sticks for SC ports.
•
•
•
•
•
Proactive cleaning before you
connect keeps contamination out of
fiber interconnections.
Prevent damage to polished fiber end faces.
Avoid contamination failures and
subsequent re-testing.
Eliminate cross-contamination from dirty
test leads.
Optimize network performance.
Protect investment in fiber infrastructure.
Cleaning Kit 1 without
Sticklers® CleanClickers®
Description
Catalog No.
Cleaning kit without
clickers
OFCLEANKT1
Cleaning Kit 2 with Sticklers®
CleanClickers®
Description
Catalog No.
Cleaning kit with LC,
SC, MPO clickers
OFCLEANKT2
Sticklers, CleanClicker, CleanStixx and CleanWipes are
trademarks of MicroCare.
Cable Management
Adhesive Kits
Fiber Management Spool
2-pack
Description
Catalog No.
Adhesive mount, yellow
OFSPOOLPK2
Cleaning Accessories
Fiber Cable Management
Radius Clips
Epoxy Adhesive Kit
Fusion Splice Sleeves
Includes: (6) tubes 1g, (6) syringes/needles
25-pack
Includes: pack of (4) self-adhering clips with
bend radius control element
Description
Catalog No.
Easy mix 1g tubes
OFCEP
Description
Catalog No.
Cable clips
FBRMGTCLPK4
OPTISOK® Pulling Grips
Loose Tube OSP Cable
Break-Out Kits
Bundle Size
Range
Catalog No.
0.125–0.562”
CCPS1
0.250–0.750”
CCPS2
Includes: tube kit, break-out block and
crimp bushing
0.750–1.750”
CCPS3
Description
Catalog No.
6-fiber break-out kit
OFBOKT6
12-fiber break-out kit
OFBOKT12
www.hubbell-premise.com
Fusion Splice
Description
Catalog No.
40mm length,
10mm cleave
FSHST401025
12-fiber ribbon
FRSHST401025
Sticklers® CleanClicker®,
SC/ST/FC/APC
Sticklers® CleanClicker®,
LC/MU/APC
Includes: (1) disposable cleaner tape cartridge
Includes: (1) disposable cleaner tape cartridge
Description
Catalog No.
Description
Catalog No.
2.5mm, SC/FC/APC
OFCLICK750SC
2.5mm, LC/MU/APC
OFCLICK750LC
Anaerobic Adhesive Kit
Includes: Primer and adhesive, (10) syringes
and (10) needles
Description
Catalog No.
Anaerobic adhesive kit
cures in 6–10 seconds
OFCAP
Replacement bottle of
primer only
OFPRIME
www.hubbell-premise.com
Fusion Splice Trays
Description
Catalog No.
Aluminum, 12-fiber
STRAY12F
Aluminum, 24-fiber
STRAY24F
Plastic, yellow, 24-fiber
OFSPLKT24F
Sticklers® CleanClicker®,
MPO/APC
Sticklers® Cleaning Fluid,
Optical
Includes: (1) disposable cleaner tape cartridge
Includes: (1) 3oz pump dispenser
Description
Catalog No.
Description
Catalog No.
MPO male, female,
flat/APC
OFCLICK600MPO
3oz cleaning fluid,
pump, non-hazardous
OFCLEANER3OZ
www.hubbell-premise.com
HUBBELL PREMISE WIRING | Fiber Optics Tooling & Maintenance Product Guide
Installation Kits
®
Connector Installation Tool Kit
Epoxy and Crimp Kit
Includes: sapphire scribe, scribe guide, black
permanent marker, carbon fiber scissors, strip
template and polishing fixture, ruler, buffer/
cable jacket stripper, 200X microscope
assembly, crimp tool and die
Includes: OFSTRIP2 and OFCMT04 tools,
polishing pucks, 200X microscope, carbon fiber
scissors, scribe, glasses, alcohol wipes
Description
Catalog No.
For SC/ST-style
connectors crimp or
adhesive termination
OFTP02C
Description
Catalog No.
Field install kit
OFTK05
Epoxy Cure Adapters
LC Duplex Connector
Extraction Tool
Includes: package of (6) adapters for heat
cure oven
Includes: (1) tool, individually packaged, ideal
for servicing high density interconnections
Description
Catalog No.
Description
Catalog No.
SC/ST-style
OFCA
Connector extraction tool
OFLCDTOOL1
LC
OFCALC
www.hubbell-premise.com
Polishing
TESTING
The fiber link total dB loss is
measured through the mated
connector pair on each end using an
insertion loss test set.
•Testers should be calibrated, and fiber ports
cleaned and inspected prior to use.
•Clean and inspect test jumpers prior to mating
into tester and fiber link ports.
•A 2-connector fiber link insertion loss should be
less than 1.5dB, excluding cable loss.
Premise Wiring
[your complete online resource]
Find what you need quickly with our
multi-functional online value-added tools—
print, zoom, search and download required
information anytime, anywhere.
Polishing Fixture
Includes: (1) stainless steel puck, polished
surface; SC/ST-style or LC compatible
Description
Catalog No.
SC/ST-style
OFPUCK
LC
OFPUCKLC
Polishing Film
[related literature]
Includes: (25) each of 5µ, 1µ and 0.3µ sheets,
(1) polishing pad
Description
Catalog No.
Replacement kit
OFLFP
Fiber Optics
Tooling & Maintenance
Product Guide
Inspecting
Microscope, 200X (ST, SC, LC)
Microscope, 400X
Includes: batteries, LC adapter, soft pouch
Includes: built-in illuminator, batteries,
SC/ST-style adapter, soft pouch
Description
Catalog No.
ST, SC, LC microscope
OFSCOPE2
Visual Fault Locators (ST, SC, LC)
Includes: batteries, LC adapter, holster, wrist
strap, end protectors
Description
Catalog No.
Visual fault locator
OFVFLKT1
LC adapter,
separate
OFVLCADP
TIP: Use a VFL during termination for optimum
test results.
Description
Catalog No.
SC/ST-style microscope
OFSCOPE1
LC adapter (400X
microscope only)
FOADPTLC
Multimode Test Set
Includes: (1) power meter, (1) dual wavelength
LED source, (1) soft pouch, batteries
Description
Catalog No.
Complete tester kit
OFPLK813A
Power meter dual wavelength OFPM813
LED light source dual
wavelength, multimode
www.hubbell-premise.com
OFLS813
Hubbell Premise Wiring • Hubbell Incorporated (Delaware) • 23 Clara Drive • Suite 103 • Mystic, CT 06355 • Phone (800) 626-0005 • FAX (860) 535-8328
www.hubbell-premise.com
Printed in U.S.A. Specifications subject to change without notice.
® is a registered trademark of Hubbell Incorporated. PLBF001 8/16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising