Quick Installation Guide

Quick Installation Guide
Applicable models: 8/16-port Cascadable rackmount 15”/17”/19” LCD KVM Switch
Firmware-Upgradable
USB PS/2 Dual Interface Support
8/16-port Cascadable Rackmount 15”/17”
LCD KVM Switch
UM33 / UM35
UM34 / UM36
8/16-port Cascadable Rackmount
15”/17” LCD KVM Switch
Quick Installation Guide
Thank you for purchasing the
UM33 / UM34 / UM35 / UM36
LCD KVM Switch! With our highly reliable and
quality products, user can enjoy countless benefits
from using it.
UM33 / UM35
8/16-port 15” LCD KVM Switch
UM34 / UM36
8/16-port 17” LCD KVM Switch
ULCM-0819/ULCM-1619
8/16-port 19” LCD KVM Switch
UM33 8-port 15” USB PS/2 LCD KVM Switch, Cascadable Rackmount
UM35 16-port 15” USB PS/2 LCD KVM Switch, Cascadable Rackmount
UM34 8-port 17” USB PS/2 LCD KVM Switch, Cascadable Rackmount
UM36 16-port 17” USB PS/2 LCD KVM Switch, Cascadable Rackmount
ULCM-0819 8-port 19” USB PS/2 LCD KVM Switch, Cascadable Rackmount
ULCM-1619 16-port 19” USB PS/2 LCD KVM Switch, Cascadable Rackmount
This LCD KVM Switch is 8/16-port 15”/17”
rackmount LCD KVM Switch that offers a
management capacity of 8/16 ports for connections
with any USB or PS/2 computers. It is designed for
computer/server management on a 19” rack in either
corporate computing environment. For rackmount
convenience, it features dual slide rails for easy and
independent access of the display panel and the
keyboard tray.
Something you should take into consideration before you
put it on a rack ….
1.
Clean and Crisp LCD display with durable
keyboard and touch pad
The Bright Active Matrix TFT display protected by
tempered glass offers a crisp and clean image. The
touch pad and keyboard are durable and robust in
operation. The LCD KVM Switch provides the OSD
Menu both for KVM switch and the LCD panel display
for screen adjustment and KVM switching operations.
Features such as Auto Logout, Password Protection
and Firmware upgrade are accessible via the OSD
Menu.
2.
3.
4.
Please check all peripherals according the list before
installation. To make sure that the whole unit was not
damaged and lost during shipping process. If you
encounter any problem, please contact your dealer.
Before installation, make sure all peripherals and
computers have been turned off.
This product required front and rear mounting brackets.
Pre-configure the depth of the rack to find the best rear
bracket kits for your usage.
The standard rear bracket kits are for 588~800 mm as
below figure, contact your dealer if you need longer rear
bracket.
Cascadable features provide scalability for
management capacity up to hundreds of
servers
Its cascadable feature can help upscale the server
number to over a hundred. Both USB and PS/2
interface support on both console side and PC side
offers maximum convenience in a computing
environment that accommodates both newer USBenabled computers and older computers with only
PS/2 interfaces.
Check the Items of the Mounting Kit
◘
Short Single Bracket X 2 (For under 650mm rack depth)
The LCD KVM Switch can serve as the master KVM
switch to be cascaded with other compatible KVM Switch
such as those rackmount KVM switches within the same
family up to at least 8 levels.
◘ Long Assembled Bracket X 2 (For 650~800mm rack depth)
USB and PS/2 interface support on both
Console and PC Side
◘ Metal Plate X 2 (For short single bracket)
The LCD KVM Switch supports both USB interface
and PS/2 interface on both console side and PC side.
It is especially useful when your server room is mixed
with some legacy computers with only PS/2
interfaces and also with some newer computers
equipped with only USB interfaces.
Before installing on a rack…
1
◘ Copper Ring X 6 (For short single bracket)
◘ Flat Screw X 6 (For short single bracket)
Rev.1.3
Copyright© All rights reserved.
Quick Installation Guide
Applicable models: 8/16-port Cascadable rackmount 15”/17”/19” LCD KVM Switch
◘ Cap Screw X 28
◘ Key X 2
B.
Rack Depth Above 650mm
6) Finish Installation as below
1)
Remove the screw of long assembled bracket and
keep screws
2)
Combine (I) to console from each side using Cap
Screw (5 pcs each side)
Rack Installation
Note:2nd person required for rear support during
installation.
A. Rack Depth Under 650mm
1) Release the Thumb Screw of front bracket (on both
sides).
2) Tighten the front brackets on both sides using cabinet
screws.
Connect to Computers
3)
Combine (I) and (II) from each side(7 pcs each side)
3)Install rear brackets on both sides.
4) Release the Thumb Screw of front bracket and Install
front bracket from each side using cabinet screws
4) Tighten rear brackets on both side using cabinet
screws
7) Attach provided cable and power cord to use
5)Combine (I)+(II) and (III) using the original screw and
Install rear bracket from each side using cabinet screws
2
Before connecting computers to the LCD
KVM switch, you mihgt need to mount it on
the server rack …..
If you are using any PS/2 computer: Please
make sure all of your PS/2 computers should be
powered off before connecting to the LCD KVM
Switch. Otherwise, the LCD KVM Switch system
might not be properly set up. However, USB
computers do not have this limitation.
Step 1. Make sure (at least the PS/2) computers that
are to be connected to the LCD KVM switch
are powered off. If not, power them off
before you proceed with the following steps.
Step 2. Connect the shared keyboard, mouse and
monitor to the console connectors on the rear
of your (master) LCD KVM switch. Power on
the LCD KVM Switch by connect power cord
and trun on the Power switch (found on the
front edge of the keyboard tray.
If you use only a single LCD KVM switch in
non-cascaded application, you should ignore step 3, 4
and 5 and jump directly to step 5.
Rev.1.3
Copyright© All rights reserved.
Quick Installation Guide
If you want to daisy-chain multiple KVM
Switches, go to step 3. You can daisy-chain up to 8
levels of KVM Switches with a maximum of 120
computers connected.
Step 3. Use the daisy-chain cable (M-HDB15HDB15-F) to connect the DaisyChain OUT
Port (HDB 15 female) of the LCD KVM
Switch to the DaisyChain IN Port (HDB 15
male) of the second KVM switch (Prima
4/Pirma 8/Prima 16). Connect the power cord
to the second switch to power it on.
Step 4. If you have yet another Prima switch to be
daisy-chained, just repeat Step 3 to connect
them. You can daisy-chain up to 16 units of
KVM switches. Plug a terminator onto the
Daisy-chain Out Port of the last KVM
switch unit.
Applicable models: 8/16-port Cascadable rackmount 15”/17”/19” LCD KVM Switch
The special KVM cable provides a PS/2 keyboard
connector, a USB connector and a HDB video
connector for the computer connection. When
connecting with a USB computer, just plug the USB
connector to it and leave the PS/2 connector free.
When connecting with a PS/2 computer, just add one
USB-to-PS/2 adapter to the USB connector and you’ll
have a PS/2 connector for mouse. Do not connect
USB connector and PS/2 keyboard connector
to a computer at the same time.
Step 6. Power up the connected computers. After
your computer is powered up the keyboard and
mouse will be recognized and now you can
begin operating the switch.
Easy Operation
There are two ways to select a specific computer,
using either keyboard hotkey sequence or OSD
Menu.
Keyboard hotkeys
A keyboard hotkey sequence consists of at least
three specific keystrokes: See Quick Reference Sheet
Hotkey sequence = ScrLk + ScrLk + Command key(s)
The two consecutive ScrLk keystrokes should be
pressed within 2 seconds and the following command
key(s) should also be pressed within 2 seconds in
likewise manner. Otherwise, the hotkey sequence will
not be validated.
For detailed Hotkey sequences
corresponding functional commands.
No Terminator required if only using a single unit.
Step 5. (Now your KVM switch or daisy-chained KVM
Switches should have been powered-up and
initialized….) Connect each of your
computers to a computer port on the rear of
the switch(es). You should use the special
USB PS/2 KVM cable (with the USB-to-PS/2
adapter) for connection to a USB computer
(PS/2 computer).
and
their
See Quick
Reference Sheet
Main OSD Menu
Setup Menu
Main menu
Select computer: use Up/Down Arrow key to
navigate, PgUp/PgDn to scroll page. Hit Enter to
select.
Edit computer name: just hit Insert to edit and Enter
to confirm change.
F1 : Next Page - rotate through Main Page / Setup
page / Status page
F10: Logout - lock your keyboard and mouse for
security. Password will be needed to log in.
Setup Menu
Autologout: specify time for auto logout (00~99 min)
OSD timeout: specify duration for OSD menu to stay
on screen
Autoscan period: specify time for autoscan period
Title bar: Enable/disable the title bar and specify the
position of the OSD title bar
Hotkey: specify the hotkey preceding sequence
(SCROLL LOCK, CAPS, ESC, F12 or NUM LOCK)
Setup Password: specify the password for access
Load Default: load the default settings to the current
bank.
Load Default All: load the default settings to all
banks.
Upgrade Firmware: upgrade the firmware of the
KVM switch
Firmware Upgrade
OSD Menu
To activate the OSD (On Screen Display) Menu, use
the hotkey sequence:
Activate OSD
= ScrLk + ScrLk + Space Bar
Deactivate OSD = ESC (Escape key)
3
This LCD KVM Switch allows its user to upgrade firmware contents
whenever is needed to enhance the compatibility to other devices
or its functions and performance. Use the firmware upgrade cable
for connection to a host PC via the “Daisy-chain IN” port (see
previous configuration diagram). For firmware upgrade procedure,
please refer to Firmware Upgrade Operation Guide.
Rev.1.3
Copyright© All rights reserved.
Quick Reference Sheet
Applicable models: 8/16-port Cascadable rackmount 15”/17”/19” LCD KVM Switch
Quick
Reference
Sheet
QUICK REFERNCE SHEET for Cascadable Rackmount LCD KVM Switch -- Operation Commands Hotkeys/ OSD Menu
Hotkey sequence = [ScrLk]* + [ScrLk] * + Command key(s) * User-definable Preceding sequence = SCROLL LOCK, CAPS, ESC, F12 or NUM LOCK
Command
Hotkeys
OSD control1
Cursor keys to navigate
Enter to select
Cursor keys to navigate
Enter to select
Cursor keys to navigate
Enter to select
Select Computer
ScrLk + ScrLk + (a) + (b) + (y) + (z)
(ab = bank no. ; xy = channel no.)2
Next lower channel
ScrLk + ScrLk + ↑ (arrow up)
Next higher channel
ScrLk + ScrLk + ↓ (arrow down)
Next lower bank
ScrLk + ScrLk + PgUp
PgUp (w/ OSD Menu)
Next higher bank
ScrLk + ScrLk + PgDn
PgDn (w/ OSD Menu)
Autoscan Beep Sound On/Off
ScrLk + ScrLk + B
--
Define Hotkey Preceding Sequence
--
Load Factory Default
--
Change Computer Name
--
Main Menu/Setup/Hotkey
[ SCROLL LOCK, CAPS, ESC, F12 or NUM LOCK]
Main Menu / Setup / Load Default (to current
bank) – Load Default All (to all banks)
Cursor keys to navigate
Enter (Ins) to select/edit
Description
Select the active bank (switch) and channel
Select the next lower connected channel within the
current active bank
Select the next higher connected channel
Select the next lower bank (switch) when with
multiple daisy-chained units
Select the next higher bank (switch ) when with
multiple daisy-chained units
Toggle on/off the beep sound for switching
confirmation while autoscanning
Select the hotkey preceding sequence among 5
alternative keys
Restore the EEPROM settings to the factory default
Change the computer name
[max. length = 8 alphanumeric characters]
Reset the KVM Switch / initialize the daisy-chain
setup
Reset / Initialize KVM (whole daisy-chain)
ScrLk + ScrLk + End
--
Show OSD Menu
ScrLk + ScrLk + (Space Bar)
--
Activate the OSD Menu on the console screen
Autoscan
ScrLk + ScrLk + S
--
Autoscan through every connected channel for quick
screen browsing of each channel.
Stop Autoscan
Any key
--
Terminate Autoscan activity
Autoscan Period
[5 ~ 10 ~ 95 seconds]
--
Main Menu / Setup / Autoscan period
Auto Logout Timeout Enable/Disable
[0 ~ 99 min ]
--
Main Menu / Setup / Auto Logout
--
Main Menu / Setup / OSD Timeout
OSD Menu Timeout
[0 ~ 60 ~ 95 seconds]
OSD Title Bar On/Off
[ON/OFF]
OSD Title Bar Position
[Left/Right]
3
Setup Password
[Disable/Enable]
ScrLk + ScrLk + T
--
Specify delay time within a range of 5 ~ 99 seconds
[default = 10 sec ]
Specify the time out for auto logout -- screen
/keyboard/mouse locked after timeout period for
security. (default = 0 = disable)
Specify the timeout for OSD menu
[default = 60 seconds; 0 = disable]
Enable/disable the OSD Title Bar [default = ON]
--
Main Menu / Setup / Title Bar
Select the OSD title bar position on your screen
--
Main Menu / Setup / Setup Password
Enable/disable password protection
[default == disable; password length <= 8 characters]
Notes:
1. OSD Menu control is only available when the OSD menu is activated on the screen. To activate the OSD menu, use the hotkey sequence ScrLk + ScrLk + (Space Bar). For detailed OSD operation reference,
please refer to the User Guide. When OSD Menu is active, the mouse will be locked until the OSD Menu is off. To reset OSD menu to default, just use a pointed needle to press the recessed opening (without
marking) just beside the DC jack on the back panel for several seconds.
2. Note that a, b, y and z each denotes a number key. (ab) = 01 ~ 16 ; (yz) = 01 ~ 08. For example, ScrLk + ScrLk + 03 + 06 is for bank 3 port 6. When using a single KVM Switch configuration, the default bank no.
is 01, therefore hit ScrLk + ScrLk + 01 + 12 for port 12 for a single KVM Switch configuration.
3. The password is up to 8-character length. You should remember the password since it is required for access to your KVM switch once you enable the password protection for your KVM switch. However, if you
forget the password and thus are blocked from KVM access, you should contact your local dealer for tech support.

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project