Mount-It! MI-1875 Height Adjustable Rolling TV Stand Owner's Manual

INSTALLATION INSTRUCTIONS
Flat Panel Display Cart
=. Ó
CAUTION: DO NOT EXCEED MAXIMUM
LISTED WEIGHT CAPACITY. SERIOUS
INJURY OR PROPERTY DAMAGE MAY
OCCUR!
400x200/300x300
400x400/600x400
Route cables along the column.
Attache the cable cover to the column to hold cables in place.
Maintenance
» Check that the bracket is secure and safe to use at regular intervals(at least every three months).
* Please contact your dealer if you have any questions.
ISSUED: DEC. 2012
NOTE: Read the entire instruction manual before you start installation and assembly.
/\ WARNING
* Do not begin the installation until you have read and understood the instructions
and warnings contained in this installation sheet. If you have any question
regarding any of the instruction or warning, please contact your local distributor.
* This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
* Always use assistant or mechanical lifting equipment to safely lift and position
equipment.
» Tighten screws firmly, but do not over tighten. Over tightening can damage the
items, greatly reducing their holding power.
e This product is intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
* The display stand is not affixed or secured to the floor and may therefore tip over
or fall if screen or stand is shaken or hit. Do not let children play alone around
stand as they could get hurt by a falling screen. Not recommended for use in
areas with heavy traffic.
14
IMPORTANT: Ensure you have received all parts according to the component checklist prior to installing.
If any parts are missing or faulty, telephone your local distributor for a replacement.
3 2) rm uy
glass shelf (x1) left support arm (x1) right support arm (x1) top plate (x1)
A B C D
left adapter bracket (x1) right adapter bracket (x1) cable cover (x5) foot pad (x1) plastic cover (x1)
E F G H |
| i
inner column (x1) base (x1) knob (x1)
J L M
— caster with
outer column (x1) caster (x2) brake (x2)
K N О
Package M
(re
ie < ЗАННМЫ
M5x14 (x4) M6x14 (x4) M8x20 (x4) M6x30 ) (x4)
M-A M-B -
eo] © D
M8x30 (x4) washer (x4) small spacer (x8) big spacer (x4)
M-E M-F M-G M-H
Package
QIU © em) O |
M6x10 (x8) ME6x30 (x4) M6x16 (x4) M6x8 (x4) D6 D6 ~ D6
P-A P-B P-C P-D washer (x8) washer (x4) plastic washer (x4) 4mm Allen key (x1)
P-E P-F P-G -
» 2
1.Install the Columns and the Support Arms
ua
UC
Attach the plastic cover to the outer
column using screws and tighten all
screws with Allen key.
—] Thread the knob into the column to secure them.
Insert the inner column into the outer
column at the desired position.
B
C
Slide the support arms along the column rails Make sure both support arms are on the same
to the desired height. level and tighten all screws to secure them.
3«
2.Install the Base
Attach the column and the foot pad to the base using the correct screws and washers.
Tighten all screws with Allen key.
» 4
5«
3.Install the Casters
/'
Л
/
Install the casters into the base holes and tighten
bottom nuts of casters at the desired height.
Tighten all top nuts to secure them.
Note: Make sure all casters
are in the same height.
Note: Lock brakes on casters to avoid
sudden movements during installation.
4.Install the Top Plate and the Glass Shelf
P-E >
P-D E
Attach the glass shelf to the installed support arms using the screws and washers, and tighten all screws with a
proper screwdriver.
» 6
74
5.Install Adapter Brackets
Lt 7
o o
o oO
o o
o о
o o
o of do o
o o
Top of TV
© ©
| д N —
5-1 For Flat Back Screen
¥
V de WE N
8——M-A/M-B/M-C
5-2 For Recessed Back Screen
Note: Choose appropriate screws, washers and spacers (if necessary) according to the type of screen.
" Position the adapter brackets as close as possible to the center of the TV.
" Screw the adapter brackets onto the TV.
Tighten all screws but do not over tighten.
» 8
9«
6.Install the TV
6a. Landscape Viewing 6b. Portrait Viewing
== =
- Ö
Remove the screw on the top plate to rotate the TV (withe attached brackets and top plate 90° , Secure with just
Attach the TV to top plate with the appropriate combination of screws and washers. removed screw in another position.
» 10