SI-64 - ibase.com.tw

SI-64 - ibase.com.tw
www.ibase.com.tw
SI-64 Series
User Manual
IBASE Technology Inc.
SI-64 User Manual
Revision
Release Date
V0.1
2013/11/05
V0.2
2014/03/10
V0.3
2015/01/06
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
2
2
SI-64 User Manual
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
No part of this manual, including the products and software described in it, may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into
any language in any form or by any means, except documentation kept by the
purchaser for backup purposes, without the express written permission of IBASE
Technology INC. (“IBASE”).
Products and corporate names mentioned in this manual may or may not be
registered trademarks or copyrights of their respective companies, and are used for
identification purposes only. All trademarks are the property of their respective
owners.
Every effort has been made to ensure that the contents of this manual are correct and
up to date. However, the manufacturer makes no guarantee regarding the accuracy of
its contents, and reserves the right to make changes without prior notice.
1
SI-64 User Manual
Table of Contents
Setting up your system ........................................................................................................ 3
Care during use .................................................................................................................... 4
Acknowledgments ............................................................................................................... 4
CHAPTER 1 INTRODUCTION .................................................................................... 6
1.1 General Description ....................................................................................................... 6
1.2 System Specifications..................................................................................................... 6
1.2.2 Dimensions ................................................................................................................. 7
1.2.3 I/O View...................................................................................................................... 8
1.3 Exploded View of the SI-64 Assembly ........................................................................... 9
1.3.1 Parts Description......................................................................................................... 9
1.4 Packing List................................................................................................................... 10
1.4.1 Optional Items .......................................................................................................... 10
2 HARDWARE INSTALLATION .................................................................................11
2.1 Installing the CPU......................................................................................................... 11
2.2 Installing the Memory ................................................................................................. 11
2.3 Installing the HDD/mSATA Module.............................................................................. 12
2.4 Installing the Wireless Module .................................................................................... 15
CHAPTER 3 MOTHERBOARD INTRODUCTION .........................................................16
3.1 Introduction ................................................................................................................. 16
Board Dimensions ........................................................................................................ 18
3.2 Setting the Jumpers ..................................................................................................... 19
3.3 Connectors on IB964 .................................................................................................... 22
CHAPTER 4 BIOS SETUP .........................................................................................28
CHAPTER 5 DRIVERS INSTALLATION .......................................................................53
5.1 Intel Chipset Software Installation Utility ................................................................... 53
5.2 VGA Drivers Installation............................................................................................... 57
5.3 Realtek HD Audio Driver Installation ........................................................................... 61
5.4 LAN Drivers Installation ............................................................................................... 63
5.5 Intel® Management Engine Interface .......................................................................... 67
5.6 Intel® USB 3.0 Drivers .................................................................................................. 70
Appendix ...............................................................................................................73
Wall Mounting Requirements............................................................................................ 73
Selecting the Location........................................................................................................ 74
Driver Installation .............................................................................................................. 75
Display Group Grid Configurations .................................................................................... 76
2
SI-64 User Manual
Safety Information
Your SI-64 is designed and tested to meet the latest standards of safety for
information technology equipment. However, to ensure your safety, it is important that
you read the following safety instructions
Setting up your system

Read and follow all instructions in the documentation before you operate your
system.

Do not use this product near water.

Set up the system on a stable surface. Do not secure the system on any unstable
plane.

Do not place this product on an unstable cart, stand, or table. The product may
fall, causing serious damage to the product.

Slots and openings on the chassis are for ventilation. Do not block or cover these
openings. Make sure you leave plenty of space around the system for ventilation.
Never insert objects of any kind into the ventilation openings.

This system should be operated from the type of power indicated on the marking
label. If you are not sure of the type of power available, consult your dealer or
local power company.

Use this product in environments with ambient temperatures between 0˚C and
40˚C.

If you use an extension cord, make sure that the total ampere rating of the
devices plugged into the extension cord does not exceed its ampere rating.

DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE
THESTORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE
80° C (176° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
3
SI-64 User Manual
Care during use

Do not walk on the power cord or allow anything to rest on it.

Do not spill water or any other liquids on your system.

When the system is turned off, a small amount of electrical current still flows.
Always unplug all power, and network cables from the power outlets before
cleaning the system.

If you encounter the following technical problems with the product, unplug the
power cord and contact a qualified service technician or your retailer.

The power cord or plug is damaged.

Liquid has been spilled into the system.

The system does not function properly even if you follow the operating
instructions.

The system was dropped or the cabinet is damaged.
Lithium-Ion Battery Warning
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer. Dispose of used
batteries according to the manufacturer’s instructions.
NO DISASSEMBLY
The warranty does not apply to the products that have been disassembled by users
WARNING
HAZARDOUS MOVING PARTS
KEEP FINGERS AND OTHER BODY PARTS AWAY
4
5
IBASE Technology Inc.
Acknowledgments

AMI is a registered trademark of AMI Software International, Inc.

AMD and ATI are registered trademarks of AMD Corporation.

Microsoft Windows is a registered trademark of Microsoft Corporation.

FINTEK is a registered trademark of FINTEK Electronics Corporation.

REALTEK is a registered trademark of REALTEK Electronics Corporation.

All other product names or trademarks are properties of their respective owners.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
CHAPTER 1 INTRODUCTION
1.1 General Description
SI-64 comes with the Intel® Q77 Express Chipset and Radeon E6760 embedded
discrete graphics processor that enables outstanding graphics experience and up to
four DVI outputs using AMD Eyefinity Technology for video wall application.
1.2 System Specifications
1.2.1 Hardware Specifications
Model Name
SI-64
System Mainboard
IB964
CPU
3rd Generation Intel® Core™ i7/i5/i3, Pentium QC/DC
Desktop Processors
*The maximum TDP supported 77W
Chipset
Intel® Q77 PCH
Memory
2 x DDR3 1600MHz DIMM, Max. 16GB (Non-ECC)
I/O Interface
3 x DVI, 1x Hybrid DVI (DVI/ VGA / HDMI with audio)
2 x USB 2.0 ports, 2 x USB 3.0 ports
2 x RJ45 for LAN, 2 x RJ45 for RS232
2 x Micro jack audio connectors for Line-in / Line-out
1 x Power / HDD LED
1 x Power on/off button
1 x Power jack
Storage
1 x mSATA
1 x 2.5” 320GB SATA 3.0 HDD
Expansion Slots
2 x Mini PCI-E(x1) slots for WiFi, 3G and TV tuner options
Power Supply
AC in, Internal 250w PSU
6
7
IBASE Technology Inc.
Construction
SGCC
Chassis Color
Black & White
Mounting
Wall mount
Dimensions
380mm(W) x 250mm(D) x 45mm(H)
14.9”(W) x 9.8”(D) x 1.77”(H)
Operating Temperature
0°C ~ 45°C
Storage Temperature
-20°C ~ 80°C
Relative Humidity
5~90% @45°C (non-condensing)
Vibration
mSATA: 5 Grms/5~500Hz random operation
RoHS
Yes
Certification
CE, FCC class B, CCC and UL
‧This specification is subject to change without prior notice.
1.2.2 Dimensions
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
1.2.3 I/O View
Item
Connector
Item
Connector
1
Power button
5
4x USB ports
2
Power/HDD LED Indicator
6
2x RJ45 for LAN
3
2x RJ45 for RS-232
7
Line-in/Line-out
4
3x DVI, 1 x Hybrid DVI
8
AC Inlet
8
9
IBASE Technology Inc.
1.3 Exploded View of the SI-64 Assembly
1.3.1 Parts Description
Part No.
Description
Part No.
1
SI-64 Base
2
IB964 motherboard
3
Power module
4
SI-64 side bracket
5
SI-64 fix bracket
7
SI-64 L-cover
8
SI-64 R-cover
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Description
SI-64 User Manual
1.4 Packing List
Item No.
Description
Qty
1
Driver CD
1
2
Screw; B30
6
3
Wall Mount Kits
2
4
Power Cord
1
1.4.1 Optional Items
WiFi Solution
Description
QCOM WiFi
module
Wireless LAN Card; 802.11 B/G/N+BT HALF Card
[Q802XKN3B] RoHS (A008WIRELESS00700P)
External Antenna
Wifi Antenna (A055RFA02C2M20800P)
Internal cable-1/2
From Wifi module to Rear/Front panel
(A055RFA0000021000P/A055RFA0000032000P)
Bracket
MPCIE-EXT V-B1 Bracket, RoHS; Extend Half to Full
size. (SC2MPCIEEXT0B1100P)
3G Solution
Description
ZU 202
Wireless; 3.75G UMTS/HSPA [ZU202] RoHS
(A008WIRELESS00520P)
ZU 200
Wireless; 3.75G UMTS/HSPA & GPS Module
[ZU200] RoHS (A008WIRELESS00510P)
Cable
Cable; Antenna-2 30CM P 2pcs
(C501ANT0200300000P)
Antenna
Antenna; 3G, P, 2pcs (A055ANT0921Q2P000P)
COM Port Cable
Description
EXT-311
Cable; EXT-311 2-HD 10C, 150CM; DSUB-9F =>
RJ45-10M RoHS (C501EXT3110A12000P)
EXT-312
Cable; EXT-312 2-HD 10C, 150CM; DSUB-9M =>
RJ45-10M RoHS (C501EXT3120A12000P)
Display Cable
Description
DVI-22
DVI-22 3-HD, 10CM; DVI => DVI, VGA-15 RoHS
(C501DVI2200103000P)
10
11
IBASE Technology Inc.
2 HARDWARE INSTALLATION
2.1 Installing the CPU
To install the CPU, unlock first the socket by pressing the lever sideways, then lift
it up to a 90-degree. Then, position the CPU above the socket such that the CPU
corner aligns with the gold triangle matching the socket corner with a small triangle.
Carefully insert the CPU into the socket and push down the lever to secure the CPU.
Then, install the heat sink and fan.
NOTE:
Ensure that the CPU heat sink and the CPU top surface are in total contact to
avoid CPU overheating problem that would cause your system to hang or be
unstable.
2.2 Installing the Memory
The IB964 board supports four DDR3 memory socket for a maximum total memory of
32GB in DDR3 DIMM memory type.
Installing and Removing Memory Modules
To install the DDR3 modules, locate the memory slot on the board and perform the
following steps:
1. Hold the DDR3 module so that the key of the DDR3 module aligned with that on the
memory slot.
2. Gently push the DDR3 module in an upright position until the clips of the slot close to
hold the DDR3 module in place when the DDR3 module touches the bottom of the slot.
3. To remove the DDR3 module, press the clips with both hands.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
2.3 Installing the HDD/mSATA Module
HDD Module:
1. Remove the two screws on the sides that are used to secure the black top cover to
the chassis. Once all the screws are removed, from the side, push the cover forward
to remove it. See steps1 and 2 in the picture.
2. Loosen the mounting screws that secure the HDD to the bracket.
12
13
IBASE Technology Inc.
3. Following the picture’s arrowed direction, push out the HDD module.
4. Loosen the four screws and then replace the HDD module.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
mSATA Module:
1. Remove the two screws on the sides that are used to secure the white top cover to
the chassis. Once all the screws are removed, from the side, push the cover forward
to remove it. See steps1 and 2 in the picture.
2. Push the mSATA module into the slot. And screw two screws to secure the module
to the slot.
14
15
IBASE Technology Inc.
2.4 Installing the Wireless Module
1. Remove the two screws on the sides that are used to secure the white top cover to
the chassis. Once all the screws are removed, from the side, push the cover forward
to remove it. See steps1 and 2 as in the picture.
2. Push the WIFI module into the slot. Screw one screw to secure the module to the
slot.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
CHAPTER 3 MOTHERBOARD INTRODUCTION
3.1 Introduction
The IB964 ATX motherboard is based on the latest Intel@ Q77 chipset. The
platform supports 3rd generation Intel@ Core processor family with LGA1155 packing
and features an integrated dual-channel DDR3 memory controller as well as a
graphics core.
The latest Intel@ processors provide advanced performance in both computing
and graphics quality. This meets the requirement of customers in the gaming, POS,
digital signage and server market segment.
The Q77 platform is made with 22 nanometer technology that supports Intel’s first
processor architecture to unite the CPU and the graphics core on the transistor level.
The IB964 ATX board utilizes the dramatic increase in performance provided this
Intel’s latest cutting-edge technology. Measuring 305mm x 244mm, the IB964 offers
fast 6Gbps SATA support (2 ports), USB3.0 (2 ports) and interfaces for DVI-D, DVI-I
and DP displays. IB964VF features Intel Active Management Technology 8.0.
Specification – Mainboard
Model
IB964
Form Factor
Customized
Model
Intel 3 Generation Core™ I7 / I5 / I3 and Pentium® QC/DC processors,
Up to 3.5GHz I7-3770
Speed
3.4GHz
Cache
8M
Socket
LGA1155
TDP
77W
CPU
®
rd
Chipset
®
Model
Intel Q77 PCH
Model
AMI BIOS, support ACPI Function
BIOS
Memory
Configuration
8GB(1.5V +-3%)
Max. Support
DDR3 sockets X2
Up to 16GB 1066/1333/1600 MHz SDRAM, w/o ECC
16
17
IBASE Technology Inc.
Edge I/O
Display
1x Hybrid-DVI (DVI/ HDMI/ VGA) + DVI
1x DVI-D + DVI-D
From AMD E6760 GPU (480 Cores @ 600 MHz; 31W) w/ 1024MB GDDR5-1600
(57.6 GB/s)
LAN / PHY
Intel 82579LM Gigabit LAN PHY + Intel 82583V PCI-Gigabit LAN
Audio
Intel® Q77 PCH built-in HD audio + Realtek ALC269QHD Codec
USB
2x USB 2.0 ports; 2 x USB 3.0 ports
LPC I / O
Fintek F81866
2x RJ45 for COM1 / COM2 (RS232)
Expansion slot
1x mPCIe(x1) (half size)
1x mPCIe(x1) (mPCIe & mSATA support SATA 3.0) (full size)
Digital IO
4 in & 4 out
Internal I/O
Audio
Header for speaker out (w/ amplifier)
SATA / eSATA
1x SATA 3.0 2.5” HDD Dock
1x SATA 2.0 Header
LPC I / O
Fintek F81866AD-I
Monitor (2 thermal inputs, 2 voltage monitor inputs & 1 Fan headers)
4-pin PWM Fan header (CPU fan)
3-pin Fan Header x 2 (SYS Fan Control)
1x10 pins pin-header x 2 for COM3&4 DO NOT POPULATE FOR SI SYSTEM
USB
2x 10 pins pin-header for two USB 2.0 DO NOT POPULATE FOR SI SYSTEM
Expansion Slot
1x mPCIe(x1) 26.8 mm
1x mPCIe(x1) 51 mm (mPCIe & mSATA)
Fan
4-pin PWM fan header (CPU fan)
3-pin Fan Header x 2 (SYS Fan Control)
Add-On Feature
Watchdog
Yes (256 segments, 0, 1, 2…255 sec/min)
H/W Monitor
Yes
iSMART
Yes
iAMT
Yes
Other
LAN Wakeup
Dimensions
PCB
305mm x 243mm
Power
250W PSU
Power Supply
Environmental
Temperature
Operating: -10°C~60°C
Humidity
10%~90% (non-condensing)
Shock
IBASE Standard Test
Vibration
IBASE Standard Test
Certification
RoHS
Other
CE/FCC Class B
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
Board Dimensions
18
19
IBASE Technology Inc.
3.2 Setting the Jumpers
Jumpers are used on IB964 to select various settings and features according to
your needs and applications. Contact your supplier if you have doubts about the best
configuration for your needs. The following lists the connectors on IB964 and their
respective functions.
Jumper Locations on IB964
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
JBAT1: Clear CMOS Contents
3
JBAT1
1
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS
JP3: Flash Descriptor Security Override (Factory use only)
2
JP3
Flash Descriptor
Security Override
Open
Disabled
(Default)
Close
Enabled
1
20
21
IBASE Technology Inc.
JP8: COM1 RS232 RI/+5V/+12V Power Setting
2
6
6
1
5
5
JP8
Setting
Function
Pin 1-3
+12V
Short/Closed
Pin 3-4
RI
Short/Closed
Pin 3-5
+5V
Short/Closed
JP9: COM2 RS232 RI/+5V/+12V Power Setting
2
6
6
1
JP9
Setting
Pin 1-3
Short/Closed
Pin 3-4
Short/Closed
Pin 3-5
Short/Closed
5
5
Function
+12V
RI
+5V
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
3.3 Connectors on IB964
22
23
IBASE Technology Inc.
CN1: SATA2 Connectors
CN2, CN3: USB3.0 Connectors
CN4: Dual DVI-D Connector
Signal Name
DATA 2DATA 2+
Shield 2/4
DATA 4DATA 4+
DDC CLOCK
DDC DATA
N.C
DATA 1DATA 1+
SHIELD 1/3
DATA 3DATA 3+
DDC POWER
A GROUND 1
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Pin #
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
C6
Signal Name
HOT POWER
DATA 0DATA 0+
SHIELD 0/5
DATA 5DATA 5+
SHIELD CLK
CLOCK CLOCK +
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
Pin #
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
C6
Signal Name
HOT POWER
DATA 0DATA 0+
SHIELD 0/5
DATA 5DATA 5+
SHIELD CLK
CLOCK CLOCK +
Red
Green
Blue
HSYNC
A GROUND2
A GROUND3
CN5: DVI-D and DVI-I Connector
Signal Name
DATA 2DATA 2+
Shield 2/4
DATA 4DATA 4+
DDC CLOCK
DDC DATA
VSYNC
DATA 1DATA 1+
SHIELD 1/3
DATA 3DATA 3+
DDC POWER
A GROUND 1
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
Signal Name
DATA 2DATA 2+
Shield 2/4
DATA 4DATA 4+
DDC CLOCK
DDC DATA
N.C
DATA 1DATA 1+
SHIELD 1/3
DATA 3DATA 3+
DDC POWER
A GROUND 1
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Pin #
16
17
18
19
20
21
22
23
24
C1
C2
C3
C4
C5
C6
Signal Name
HOT POWER
DATA 0DATA 0+
SHIELD 0/5
DATA 5DATA 5+
SHIELD CLK
CLOCK CLOCK +
N.C.
N.C.
N.C.
N.C.
N.C.
N.C.
CN6: Gigabit LAN (Intel 82579LM)
CN7: Gigabit LAN (Intel 82583V)
CN8, CN9: RJ45 For COM Port
Pin #
Signal Name
1
2
3
4
5
6
7
8
9
10
DSR, Data set ready
GND, ground
GND, ground
TXD, Transmit data
RXD, Receive data
DCD, Data carrier detect
DTR, Data terminal ready
CTS, Clear to send
RTS, Request to send
RI, Ring indicator
CN12, CN13: HD Audio Connector
COM3, COM4: RS232 Serial Ports
Signal Name Pin #
DCD#
1
SIN#
2
SOUT
3
DTR#
4
GND
5
Pin # Signal Name
6
DSR#
7
RTS#
8
CTS#
9
RI#
X
KEY
SATA1: SATA3.0 Connectors
JP1: Compact Flash Connector
24
25
IBASE Technology Inc.
J1: ATX Power Supply Connector
Signal Name
Pin #
Pin #
Signal Name
3.3V
11
1
3.3V
-12V
12
2
3.3V
Ground
13
3
Ground
PS-ON
14
4
+5V
Ground
15
5
Ground
Ground
16
6
+5V
Ground
17
7
Ground
-5V
18
8
Power good
+5V
19
9
5VSB
+5V
20
10
+12V
J2: ATX 12V Power Connector
This connector supplies the CPU operating voltage.
Pin #
1
2
3
4
Signal Name
Ground
Ground
+12V
+12V
J6, J10: USB Connectors
Signal Name
VCC
D0D0+
GND
KEY
Pin #
1
3
5
7
9
Pin #
2
4
6
8
10
Signal Name
VCC
D1D1+
GND
NC
J11: Mini-PCIE Connector
J12: Mini-PCIE Connector and mSATA/share with SATA3.0
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
J14: Digital I/O
Signal Name
Pin#
Pin#
Signal Name
GND
1
2
VCC
OUT3
3
4
OUT1
OUT2
5
6
OUT0
IN3
7
8
IN1
IN2
9
10
IN0
J19, J20: COM3, COM4 RS232 Serial Ports
Signal Name
Pin #
Pin #
Signal Name
DCD#
1
6
DSR#
SIN#
2
7
RTS#
SOUT
3
8
CTS#
DTR#
4
9
RI#
GND
5
X
KEY
JP4: LPC debug Connector (Factory use only)
1
2
9
10
CPU_FAN1: CPU Fan Power Connector
Pin #
Signal Name
1
Ground
2
+12V
3
Rotation detection
4
Control
26
27
IBASE Technology Inc.
SYS_FAN1: System Fan1 Power Connector
Pin #
Signal Name
1
Ground
2
+12V
3
Rotation detection
SYS_FAN2: System Fan2 Power Connector
Pin #
Signal Name
1
Ground
2
+12V
3
NC
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
CHAPTER 4 BIOS SETUP
This chapter describes the different settings available in the AMI BIOS that
comes with the board. The topics covered in this chapter are as follows:
BIOS Introduction
The BIOS (Basic Input/Output System) installed in your computer system’s ROM
supports Intel processors. The BIOS provides critical low-level support for a standard
device such as disk drives, serial ports and parallel ports. It also password protection
as well as special support for detailed fine-tuning of the chipset controlling the entire
system.
BIOS Setup
The BIOS provides a Setup utility program for specifying the system configurations
and settings. The BIOS ROM of the system stores the Setup utility. When you turn on
the computer, the BIOS is immediately activated. Pressing the <Del> key immediately
allows you to enter the Setup utility. If you are a little bit late pressing the <Del> key,
POST (Power On Self Test) will continue with its test routines, thus preventing you
from invoking the Setup. If you still wish to enter Setup, restart the system by pressing
the ”Reset” button or simultaneously pressing the <Ctrl>, <Alt> and <Delete> keys.
You can also restart by turning the system Off and back On again. The following
message will appear on the screen:
Press <DEL> to Enter Setup
In general, you press the arrow keys to highlight items, <Enter> to select, the <PgUp>
and <PgDn> keys to change entries, <F1> for help and <Esc> to quit.
When you enter the Setup utility, the Main Menu screen will appear on the screen.
The Main Menu allows you to select from various setup functions and exit choices.
Warning: It is strongly recommended that you avoid making any
changes to the chipset defaults. These defaults have been
carefully chosen by both AMI and your system manufacturer
to provide the absolute maximum performance and
reliability. Changing the defaults could cause the system to
become unstable and crash in some cases.
28
29
IBASE Technology Inc.
Main Settings
Aptio Setup Utility – Copyright © 2011 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
BIOS Information
System Language
System Date
Access Level
[English]
[Tue 01/20/2009]
Administrator
Security
Save & Exit
Choose the system
default language
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1:General Help
F2:Previous Values
F3: Optimized Default
F4: Save ESC: Exit
System Language
Choose the system default language.
System Date
Set the Date. Use Tab to switch between Data elements.
System Time
Set the Time. Use Tab to switch between Data elements.
Advanced Settings
This section allows you to configure and improve your system and allows you to set up some
system features according to your preference.
Aptio Setup Utility
Main
Advanced
Chipset
Boot
► PCI Subsystem Settings
► ACPI Settings
► Wake up event setting
► Trusted Computing
► CPU Configuration
► SATA Configuration
► Shutdown Temperature Configuration
► iSmart Controller
► AMT Configuration
► Acoustic Management Configuration
► USB Configuration
► F81866 Super IO Configuration
► F81866 H/W Monitor
► CPU PPM Configuration
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Security
Save & Exit
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1:General Help
F2:Previous Values
F3: Optimized Default
F4: Save ESC: Exit
SI-64 User Manual
PCI Subsystem Settings
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
PCI Bus Driver Version
V 2.0502
PCI 64bit Resources Handing
Above 4G Decoding
Disabled
PCI Common Settings
PCI Latency Timer
VGA Palette Snoop
PERR# Generation
SERR# Generation
32 PCI Bus Clocks
Disabled
Disabled
Disabled
Save & Exit
→ ← Select Screen
► PCI Express Settings
↑↓ Select Item
Enter: Select
+- Change Field
F1:General Help
F2:Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Above 4G Decoding
Enables or Disables 64bit capable devices to be decoded in above 4G address space (only if
system supports 64 bit PCI decoding).
PCI Latency Timer
Value to be programmed into PCI Latency Timer Register.
VGA Palette Snoop
Enables or disables VGA Palette Registers Snooping.
PERR# Generation
Enables or disables PCI device to generate PERR#.
SERR# Generation
Enables or disables PCI device to generate SERR#.
PCI Express Settings
Change PCI Express devices settings.
30
31
IBASE Technology Inc.
PCI Express Settings
Aptio Setup Utility
Main
Advanced
Chipset
PCI Express Device Register Settings
Relaxed Ordering
Extended Tag
No Snoop
Maximum Payload
Maximum Read Request
PCI Express Link Register Settings
ASPM Support
WARNING: Enabling ASPM may cause
some PCI-E devices to fail
Extended Synch
Link Training Retry
Link Training Timeout (uS)
Unpopulated Links
Boot
Security
Save & Exit
Disabled
Disabled
Enabled
Auto
Auto
Disabled
Disabled
Disabled
5
100
Keep Link ON
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Relaxed Ordering
Enables or disables PCI Express Device Relaxed Ordering.
Extended Tag
If ENABLED allows device to use 8-bit Tag field as a requester.
No Snoop
Enables or disables PCI Express Device No Snoop option.
Maximum Payload
Set Maximum Payload of PCI Express Device or allow System BIOS to select the value.
Maximum Read Request
Set Maximum Read Request Size of PCI Express Device or allow System BIOS to select the
value.
ASPM Support
Set the ASPM Level: Force L0s – Force all links to L0s State:
AUTO – BIOS auto configure:
DISABLE – Disables ASPM.
Extended Synch
If ENABLED allows generation of Extended Synchronization patterns.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
Link Training Retry
Defines number of Retry Attempts software will take to retrain the link if previous training
attempt was unsuccessful.
Link Training Timeout (uS)
Defines number of Microseconds software will wait before polling ‘Link Training’ bit in Link
Status register. Value range from 10 to 1000 uS.
Unpopulated Links
In order to save power, software will disable unpopulated PCI Express links, if this option set
to ‘Disable Link’.
ACPI Settings
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
ACPI Settings
→ ← Select Screen
Enable Hibernation
Enabled
ACPI Sleep State
S3 (Suspend to R…)
Lock Legacy Resources
S3 Video Repost
Disabled
Disabled
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Enable Hibernation
Enables or Disables System ability to Hibernate (OS/S4 Sleep State). This option may be not
effective with some OS.
ACPI Sleep State
Select ACPI sleep state the system will enter, when the SUSPEND button is pressed.
Lock Legacy Resources
Enabled or Disabled Lock of Legacy Resources.
S3 Video Repost
Enable or disable S3 Video Repost.
32
33
IBASE Technology Inc.
Wake up event settings
Aptio Setup Utility
Advanced
Main
Chipset
Boot
Security
Wake system with Fixed Time
Wake up hour
Wake up minute
Wake up second
Disabled
0
0
0
Wake on Ring
Disabled
Wake on PCI PME
Disabled
Wake on PCIE Wake Event
Disabled
Save & Exit
→ ← Select Screen
↑↓Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Wake system with Fixed Time
Enables or Disables System wake on alarm event. When enabled, System will wake on the
hr::min:: sec specified.
Wake on PCIE PME Wake Event
The options are Disabled and Enabled.
Trusted Computing
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
TPM Configuration
TPM SUPPORT
Disabled
Current TPM Status Information
TPM SUPPORT OFF
Save & Exit
→ ← Select Screen
↑↓Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
TPM Support
This configuration is supported only with IB964VF. Enables or Disables TPM support. O.S.
will not show TPM. Reset of platform is required.
Security Device Support
Enables or disables BIOS support for security device. O.S. will not show Security Device.
TCG EFI protocol and INT1A interface will not be available.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
CPU Configuration
This section shows the CPU configuration parameters.
Aptio Setup Utility
Main
Advanced
CPU Configuration
Chipset
Boot
Security
Save & Exit
Intel® Core ™ i7-3770 CPU @ 3.40GHz
Processor Stepping
306a8
Microcode Revision
c
Max CPU Speed
3400 MHz
Min CPU Speed
1600 MHz
CPU Speed
3400 MHz
Processor Cores
4
Intel HT Technology
Supported
Intel VT-x Technology
Supported
Intel SMX Technology
Supported
64-bit
Supported
Hyper-threading
Active Processor Cores
Limit CPUID Maximum
Execute Disable Bit
Intel Virtualization Technology
Hardware Prefetcher
Adjacent Cache Line Prefetch
Enabled
All
Disabled
Enabled
Disabled
Disabled
Enabled
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1:General Help
F2:Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Hyper-threading
Enabled for Windows XP and Linux (OS optimized for Hyper-Threading Technology) and
Disabled for other OS (OS not optimized for Hyper-Threading Technology). When Disabled,
only one thread per enabled core is enabled.
Active Processor Cores
Number of cores to enable in each processor package.
Limit CPUID Maximum
Disabled for Windows XP.
Execute Disable Bit
XD can prevent certain classes of malicious buffer overflow attacks when combined with a
supporting OS (Windows Server 2003 SP1, Windows XP SP2, SuSE Linux 9.2, Re33dHat
Enterprise 3 Update 3.)
34
35
IBASE Technology Inc.
Intel Virtualization Technology
When enabled, a VMM can utilize the additional hardware capabilities provided by
Vanderpool Technology.
Hardware Prefetcher
To turn on/off the Mid level Cache (L2) streamer Prefetcher.
Adjacent Cache Line Prefetch
To turn on/off prefetching of adjacent cache lines.
SATA Configuration
Aptio Setup Utility
Main
Advanced
Chipset
Boot
SATA Controller(s)
Enabled
SATA Mode Selection
AHCI
Aggressive LPM Support
Enabled
SATA Controller Speed
Gen3
SATA Port0
Empty
Software Preserve
SATA Port1
Software Preserve
SATA Port2
Software Preserve
SATA Port3
Software Preserve
SATA Port4
Software Preserve
SATA Port5
Software Preserve
Security
Save & Exit
Unknown
Empty
Unknown
Empty
Unknown
Empty
Unknown
Empty
Unknown
Empty
Unknown
SATA Controller(s)
Enable / Disable Serial ATA Controller.
SATA Mode Selection
(1) IDE Mode.
(2) AHCI Mode.
(3) RAID Mode.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
→ ← Select Screen
↑↓Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
SI-64 User Manual
Shutdown Temperature Configuration
Aptio Setup Utility
Main
Advanced
Chipset
APCI Shutdown Temperature
Boot
Security
Disabled
Save & Exit
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1:General Help
F2:Previous Values
F3: Optimized Default
F4: Save ESC: Exit
ACPI Shutdown Temperature
The default setting is Disabled.
36
37
IBASE Technology Inc.
iSmart Controller
Aptio Setup Utility
Advanced
Main
Chipset
Boot
Security
Save & Exit
iSmart Controller
Power-On after Power failure
Disable
Schedule Slot 1
None
Schedule Slot 2
None
ISmart Controller
Setup the power on time for the system.
Schedule Slot 1 / 2
Setup the hour/minute for system power on.
AMT Configuration
Aptio Setup Utility
Main
Advanced Chipset
Boot
Security
Save & Exit
Intel AMT
Enabled
BIOS Hotkey Pressed
Disabled
MEBx Selection Screen
Disabled
Hide Un-Configure ME Confirmation
Disabled
Un-Configure ME
Disabled
Amt Wait Timer
0
Activate Remote Assistance Process
Disabled
→ ← Select Screen
USB Configure
Enabled
PET Progress
Enabled
AMT CIRA Timeout
0
Watchdog
Disabled
↑↓ Select Item
Enter: Select
+- Change Field
F1:General Help
F2:Previous Values
F3: Optimized Default
F4: Save ESC: Exit
OS Timer
0
BIOS Timer
0
AMT Configuration
This configuration is supported only with IB964VF (with iAMT function). Options are
Enabled and Disabled.
Note: iAMT H/W is always enabled. This option just controls the BIOS extension execution.
If enabled, this requires additional firmware in the SPI device.
Unconfigure ME
This configuration is supported only with IB964VF (with iAMT function). Perform AMT/ME
unconfigure without password operation.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
AMT Wait Timer
Set timer to wait before sending ASF_GET_BOOT_OPTIONS.
Activate Remote Assistance Process
Trigger CIRA boot.
PET Progress
User can Enable/Disable PET Events progress to receive PET events or not.
Watchdog Timer
This configuration is supported only with IB964VF (with iAMT function). Enable/Disable
Watchdog Timer.
Acoustic Management Configuration
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
Acoustic Management Configuration
Acoustic Management
Disabled
USB Configuration
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
USB Configuration
USB Devices:
2 Hubs
Legacy USB Support
Enabled
USB3.0 Support
Enabled
XHCI Hand-off
Enabled
EHCI Hand-off
Enabled
Port 60/64 Emulation
Enabled
USB hardware delays and time-outs:
USB Transfer time-out
20 sec
Device reset tine-out
20 sec
Device power-up delay
Auto
→ ← Select Screen
↑↓
Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
38
39
IBASE Technology Inc.
Legacy USB Support
Enables Legacy USB support.
AUTO option disables legacy support if no USB devices are connected.
DISABLE option will keep USB devices available only for EFI applications.
USB3.0 Support
Enable/Disable USB3.0 (XHCI) Controller support.
XHCI Hand-off
This is a workaround for OSes without XHCI hand-off support. The XHCI ownership change
should be claimed by XHCI driver.
EHCI Hand-off
Enabled/Disabled. This is a workaround for OSes without EHCI hand-off support. The EHCI
ownership change should be claimed by EHCI driver.
Port 64/60 Emulation
Enables I/O port 60h/64h emulation support. This should be enabled for the complete USB
keyboard legacy support for non-USB aware OSes.
USB Transfer time-out
The time-out value for Control, Bulk, and Interrupt transfers.
Device reset tine-out
USB mass Storage device start Unit command time-out.
Device power-up delay
Maximum time the device will take before it properly reports itself to the Host Controller.
‘Auto’ uses default value: for a Root port it is 100ms, for a Hub port the delay is taken from
Hub descriptor.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
F81866 Super IO Configuration
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
Super IO Configuration
F81866 Super IO Chip
F81866
► Serial Port 0 Configuration
► Serial Port 1 Configuration
► Serial Port 2 Configuration
► Serial Port 3 Configuration
F81866 ERP Support
All Enable
USB3.0 Port0/1 POWER Management
Enabled
USB3.0 Port2/3 POWER Management
Enabled
→ ← Select Screen
↑↓Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Serial Port Configuration
Set Parameters of Serial Ports. User can Enable/Disable the serial port and Select an optimal
settings for the Super IO Device.
40
41
IBASE Technology Inc.
F81866 H/W Monitor
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
PC Health Status
CPU_Fan1 smart fan control
SYS_Fan1 smart fan control
SYS_Fan2 smart fan control
50 C
50 C
50 C
CPU temperature
+41 C
SYS temperature
+35 C
CPU_FAN1 Speed
2115 RPM
SYS_FAN1 Speed
N/A
SYS_FAN2 Speed
N/A
Vcore
+1.000 V
+5V
+5.213 V
+12V
+12.408 V
1.5V
+1.544 V
+3.3V
+3.424 V
→ ← Select Screen
↑↓Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Temperatures/Voltages
These fields are the parameters of the hardware monitoring function feature of the
motherboard. The values are read-only values as monitored by the system and show the PC
health status.
Fan1/Fan2 Smart Fan Control
This field enables or disables the smart fan feature. At a certain temperature, the fan starts
turning. Once the temperature drops to a certain level, it stops turning again.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
CPU PPM Configuration
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
CPU PPM Configuration
EIST
Enabled
Turbo Mode
Enabled
→ ← Select Screen
↑↓Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
EIST
Enable/Disable Intel SpeedStep.
Chipset Settings
This section allows you to configure and improve your system and allows you to set up some
system features according to your preference.
Aptio Setup Utility
Main
Advanced
Chipset
► PCH-IO Configuration
► System Agent (SA) Configuration
Boot
Security
Save & Exit
→ ← Select Screen
↑↓Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
42
43
IBASE Technology Inc.
PCH-IO Configuration
This section allows you to configure the North Bridge Chipset.
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Intel PCH RC Version
1.1.0.0
Intel PCH SKU Name
Q77
Intel PCH Rev ID
O4/C1
Security
Save & Exit
► PCI Express Configuration
► USB Configuration
► PCH Azalia Configuration
PCH LAN Controller
Wake on LAN
Enabled
Enabled
High Precision Event Timer Configuration
High Precision Timer
Enabled
SLP_S4 Assertion Width
4-5 Seconds
Restore AC Power Loss
Power On
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1:General Help
F2:Previous Values
F3: Optimized Default
F4: Save ESC: Exit
PCH LAN Controller
Enable or disable onboard NIC.
Wake on LAN
Enable or disable integrated LAN to wake the system. (The Wake On LAN cannot be
disabled if ME is on at Sx state.)
SLP_S4 Assertion Width
Select a minimum assertion width of the SLP_S4# signal.
Restore AC Power Loss
Select AC power state when power is re-applied after a power failure.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
PCI Express Configuration
Main
Advanced
Chipset
Boot
Security
Save & Exit
PCI Express Configuration
PCI Express Clock Gating
Enabled
DMI Link ASPM Control
Enabled
DMI Link Extended Synch Control
Disabled
PCIe-USB Glitch W/A
Disabled
Subtractive Decode
Disabled
► PCI Express Root Port 1
► PCI Express Root Port 2
► PCI Express Root Port 3
► PCI Express Root Port 4
► PCI Express Root Port 5
PCI-E Port 6 is assigned to LAN
► PCI Express Root Port 7
► PCI Express Root Port 8
→ ← Select Screen
↑↓Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
PCI Express Clock Gating
Enable or disable PCI Express Clock Gating for each root port.
DMI Link ASPM Control
The control of Active State Power Management on both NB side and SB side of the DMI
link.
PCIe-USB Glitch W/A
PCIe-USB Glitch W/A for bad USB device(s) connected behind PCIE/PEG port.
44
45
IBASE Technology Inc.
USB Configuration
Main
Advanced
Chipset
Boot
Security
Save & Exit
USB Configuration
XHCI Pre-Boot Driver
Enabled
xHCI Mode
Smart Auto
HS Port #1 Switchable
Enabled
HS Port #2 Switchable
Enabled
HS Port #3 Switchable
Enabled
HS Port #4 Switchable
Enabled
xHCI Streams
Enabled
EHCI1
Enabled
EHCI2
Enabled
USB Ports Per-Port Disable Control
Disabled
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
HS Port #1/2/3/4 Switchable
Allows for HS port switching between xHCI and EHCI. If disabled, port is routed to EHCI. If
HS port is routed to xHCI, the corresponding SS port is enabled.
xHCI Streams
Enable or disable xHCI Maximum Primary Stream Array Size.
EHCI1/2
Control the USAB EHCI (USB 2.0) functions. One EHCI controller must always be enabled.
USB Ports Per-Port Disable Control
Control each of the USB ports (0~13) disabling.
PCH Azalia Configuration
Main
Advanced
Chipset
Boot
Security
PCH Azalia Configuration
Azalia
Auto
Azalia
Control Detection of the Azalia device.
Disabled = Azalia will unconditionally disabled.
Enabled Azalia will be unconditionally enabled.
Auto = Azalia will be enabled if present, disabled otherwise.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
Save & Exit
SI-64 User Manual
System Agent (SA) Configuration
Aptio Setup Utility
Main
Advanced
Chipset
System Agent Bridge Name
Boot
Security
Save & Exit
IvyBridge
System Agent RC Version
1.1.0.0
VT-d Capability
Supported
VT-d
Enabled
CHAP Device (B0:D7:F0)
Disabled
Thermal Device (B0:D4:F0)
Disabled
Enable NB CRID
Disabled
BDAT ACPI Table Support
Disabled
C-State Pre-Wake
Enabled
► Graphics Configuration
► Memory Configuration
VT-d
Check to enable VT-d function on MCH.
Enable NB CRID
Enable or disable NB CRID WorkAround.
C-State Pre-Wake
Controls C-State Pre-Wake feature for ARAT, in SSKPD[57].
→ ← Select Screen
↑↓Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
46
47
IBASE Technology Inc.
Graphics Configuration
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
Graphics Configuration
IGFX VBIOS Version
2132
IGfx Frequency
350 MHz
Primary Display
Auto
Internal Graphics
Auto
GTT Size
2MB
Aperture Size
256MB
DVMT Pre-Allocated
64M
DVMT Total Gfx Mode
Disabled
► LCD Control
→ ← Select Screen
↑↓
Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Primary Display
Select which of IGFX/PEG/PCI graphics device should be primary display or select SG for
switchable Gfx.
Internal Graphics
Keep IGD enabled based on the setup options.
DVMT Pre-Allocated
Select DVMT 5.0 Pre-Allocated (Fixed) graphics memory size used by the internal graphics
device.
DVMT Total Gfx Mem
Select DVMT 5.0 total graphics memory size used by the internal graphics device.
Gfx Low Power Mode
This option is applicable for SFF only.
Primary IGFX Boot Display (LCD Control)
Select the Video Device that will be activated during POST. This has no effect if external
graphics present. Secondary booty display selection will appear based on your selection.
VGA modes will be supported only on primary display.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
Memory Configuration
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
Memory Information
Memory Frequency
1333 MHz
Total Memory
8192 MB (DDR3)
DIMM#0
2048 MB (DDR3)
DIMM#1
2048 MB (DDR3)
DIMM#2
2048 MB (DDR3)
DIMM#3
2048 MB (DDR3)
CAS Latency (tCL)
9
Minimum delay time
CAS to RAS (tRCDmin)
9
Row Precharge (tRPmin)
9
Active to Precharge (tRASmin)
24
→ ← Select Screen
↑↓Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
48
49
IBASE Technology Inc.
Boot Settings
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
Boot Configuration
Setup Prompt Timeout
1
Bootup NumLock State
On
Quiet Boot
Disabled
Fast Boot
Disabled
CSM16 Module Version
07.69
GateA20 Active
Upon Request
Option ROM Messages
Force BIOS
INT19 Trap Response
Immediate
Boot Option Priorities
→ ← Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
► CSM parameters
Setup Prompt Timeout
Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting.
Bootup NumLock State
Select the keyboard NumLock state.
Quiet Boot
Enables/Disables Quiet Boot option.
Fast Boot
Enables/Disables boot with initialization of a minimal set of devices required to launch active
boot option. Has no effect for BBS boot options.
GateA20 Active
UPON REQUEST – GA20 can be disabled using BIOS services.
ALWAYS – do not allow disabling GA20; this option is useful when any RT code is
executed above 1MB.
Option ROM Messages
Set display mode for Option ROM. Options are Force BIOS and Keep Current.
INT19 Trap Response
Enable: Allows Option ROMs to trap Int 19.
Boot Option Priorities
Sets the system boot order.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
CSM parameters
This section allows you to configure the boot settings.
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Launch CSM
Always
Boot option filter
UEFI and Legacy
Launch PXE OpROM policy
Do not launch
Launch Storage OpROM policy
Legacy only
Launch Video OpROM policy
Legacy only
Other PCI device ROM priority
Legacy OpROM
Save & Exit
→ ← Select Screen
↑↓Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Boot option filter
This option controls what devices system can boot to.
Launch PXE OpROM policy
Controls the execution of UEFI and Legacy PXE OpROM.
Launch Storage OpROM policy
Controls the execution of UEFI and Legacy Storage OpROM.
Launch Video OpROM policy
Controls the execution of UEFI and Legacy Video OpROM.
Other PCI device ROM priority
For PCI devices other than Network, Mass storage or Video defines which OpROM to
launch.
50
51
IBASE Technology Inc.
Security Settings
This section allows you to configure and improve your system and allows you to set up some
system features according to your preference.
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
Password Description
If ONLY the Administrator’s password is set, then this
only limit access to Setup and is only asked for when
entering Setup.
If ONLY the User’s password is set, then this is a power
on password and must be entered to boot or enter
Setup. In Setup the User will have Administrator rights
The password length must be
in the following range:
Minimum length
3
Maximum length
20
Administrator Password
User Password
Administrator Password
Set Setup Administrator Password.
User Password
Set User Password.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
→ ← Select Screen
↑↓
Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
SI-64 User Manual
Save & Exit Settings
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
Save Changes and Exit
Discard Changes and Exit
Save Changes and Reset
Discard Changes and Reset
Save Options
Save Changes
Discard Changes
Restore Defaults
Save as User Defaults
Restore User Defaults
Save Changes and Exit
Exit system setup after saving the changes.
Discard Changes and Exit
Exit system setup without saving any changes.
Save Changes and Reset
Reset the system after saving the changes.
Discard Changes and Reset
Reset system setup without saving any changes.
Save Changes
Save Changes done so far to any of the setup options.
Discard Changes
Discard Changes done so far to any of the setup options.
Restore Defaults
Restore/Load Defaults values for all the setup options.
Save as User Defaults
Save the changes done so far as User Defaults.
Restore User Defaults
Restore the User Defaults to all the setup options.
→ ← Select Screen
↑↓Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
52
53
IBASE Technology Inc.
CHAPTER 5 DRIVERS INSTALLATION
This section describes the installation procedures for software and drivers. The
software and drivers are included with the motherboard. If you find the items missing,
please contact the vendor where you made the purchase.
IMPORTANT NOTE:
After installing your Windows operating system, you must install first the Intel Chipset
Software Installation Utility before proceeding with the drivers installation.
5.1 Intel Chipset Software Installation Utility
The Intel Chipset Drivers should be installed first before the software drivers to
enable Plug & Play INF support for Intel chipset components. Follow the instructions
below to complete the installation.
1. Insert the CD that comes with the board. Click SI-64/IB964 Drivers.
2. Click Intel(R) Chipset Software Installation Utility.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
3. When the Welcome screen to the Intel® Chipset Device Software appears, click
Next to continue.
54
55
IBASE Technology Inc.
4. Click Yes to accept the software license agreement and proceed with the
installation process.
5. On the Readme File Information screen, click Next to continue the installation.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
6. The Setup process is now complete. Click Finish to restart the computer and for
changes to take effect.
56
57
IBASE Technology Inc.
5.2 VGA Drivers Installation
To install the VGA drivers, follow the steps below.
1. Insert the CD that comes with the board. Click SI-64/IB964 Drivers.
2. Click AMD Radeon E6760 Graphics Driver.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
3. When the Welcome screen appears, click Next to continue.
4. Select the language you would like to be displayed and click Next.
58
59
IBASE Technology Inc.
5. Click Install to continue the installation process..
6. Select Express and the installation location and click Next.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
7. Click Accept to accept the End User License Agreement.
8. To reboot the system, click Yes.
9. Setup complete. Click Finish to restart the computer and for changes to take effect.
60
61
IBASE Technology Inc.
5.3 Realtek HD Audio Driver Installation
Follow the steps below to install the Realtek HD Audio Drivers.
1. Insert the CD that comes with the board. Click SI-64/IB964 Drivers.
2. Click Realtek High Definition Audio Driver.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
3. On the Welcome to the InstallShield Wizard screen, click Next to proceed with and
complete the installation process.
4. The InstallShield Wizard Complete. Click Finish to restart the computer and for
changes to take effect.
62
63
IBASE Technology Inc.
5.4 LAN Drivers Installation
1. Insert the CD that comes with the board. Click SI-64/IB964 Drivers.
2. Click Intel(R) PRO LAN Network Driver.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
3. Click Install Drivers and Software.
4. When the Welcome screen appears, click Next.
64
65
IBASE Technology Inc.
5. Click Next to to agree with the license agreement.
6. Click the checkbox for Drivers in the Setup Options screen to select it and click
Next to continue.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
7. The wizard is ready to begin installation. Click Install to begin the installation.
8. When InstallShield Wizard is complete, click Finish.
66
67
IBASE Technology Inc.
5.5 Intel® Management Engine Interface
Follow the steps below to install the Intel Management Engine.
1. Insert the CD that comes with the board. Click SI-64/IB964 Drivers and then Intel(R)
AMT 8.0 Drivers.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
2. When the Welcome screen for Intel® Management Engine Components, click the
checkbox for Install Intel® Control Center & click Next.
3. Click Yes to to agree with the license agreement.
68
69
IBASE Technology Inc.
4. When the Setup Progress screen appears, click Next. Then, click Finish when the
setup progress has been successfully installed.
[
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
5.6 Intel® USB 3.0 Drivers
1. Insert the CD that comes with the board. Click SI-64/IB964 Drivers.
2. Click Intel(R) USB 3.0 Drivers.
70
71
IBASE Technology Inc.
3. When the Welcome screen to the InstallShield Wizard for Intel® USB 3.0
eXtensible Host Controller Driver, click Next.
4. Click Yes to to agree with the license agreement and continue the installation.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
5. On the Readme File Information screen, click Next to continue the installation of
the Intel® USB 3.0 eXtensible Host Controller Driver.
6. Setup complete. Click Finish to restart the computer and for changes to take effect.
72
73
IBASE Technology Inc.
Appendix
A. Mounting SI-64 to the Wall
You can install SI-64 on plastic (LCD monitor), wood, drywall surface over studs, or
a solid concrete or metal plane directly. Ensure the installer uses at least four M3
length 6mm screws to secure the system on wall. Four M3 length 6mm screws
are recommended to secure the system on wall.
Fasteners are not included with the unit, and must be supplied by the installer. The
types of fasteners required are dependent on the type of wall construction. Choose
fasteners that are rated either ”Medium Duty“ or ”Heavy Duty.“ To assure proper
fastener selection and installation, follow the fastener manufacturer’s
recommendations.
Wall Mounting Requirements
Note: Before mounting the system on wall, ensure that you are following all
applicable building and electric codes.
When mounting, ensure that you have enough room for power and signal cable
routing. And have good ventilation for power adapter. The method of mounting must
be able to support weight of the SI-38N plus the suspend weight of all the cables to
be attached to the system. Use the following methods for mounting your system:
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
Mounting to hollow walls

Method 1: Wood surface – A minimum wood thickness – 38mm (1.5in.) by
25.4 cm (10in.) – of high, construction – grade wood is recommended.
Note: This method provides the most reliable attachment of the unit with
little risk that the unit will come loose or require ongoing maintenance.

Method 2: Drywall walls - Drywall over wood studs is acceptable.
Mounting to a solid concrete or brick wall - Mounts on a flat smooth surface.
Selecting the Location
Plan the mounting location thoroughly. Locations such as walkway areas, hallways,
and crowded areas are not recommended. Mount the unit to a flat, sturdy,
structurally sound column or wall surface.
The best mounting surface is a standard countertop, cabinet, table, or other
structure that is minimally the width and length of the unit. This recommendation
reduces the risk that someone may accidentally walk into and damage the device.
Local laws governing the safety of individuals might require this type of
consideration.
74
75
IBASE Technology Inc.
B. ATI Eyefinity Setting
IBASE offers user-friendly and powerful video solution in the form of SI-64
(Signature Book) with AMD Eyefinity function. Each IBASE SI-64 (Signature Book)
with Eyefinity function can drive up to 4 displays with different display configuration.
Driver Installation
Before using SI-64 (Signature Book)’s AMD Eyefinity function, the user must install
Both AMD Catalyst™ Display Driver 13.151.
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
Display Group Grid Configurations
1. Please chose Select “AMD Eyefinity Multi-Display”
76
77
IBASE Technology Inc.
SI-64 with ATI Eyefinity for 3 displays output:
Copyright © 2013 IBASE Technology Inc. All Rights Reserved.
SI-64 User Manual
SI-64 with ATI Eyefinity for 4 displays output:
78
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising