Voyager 1602g
Voyager 1602g
Wireless Area-Imaging Pocket Scanner
User’s Guide
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this
document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been
made. The information in this publication does not represent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages
resulting from the furnishing, performance, or use of this material. HII disclaims all responsibility for the selection and use of
software and/or hardware to achieve intended results.
This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document
may be photocopied, reproduced, or translated into another language without the prior written consent of HII.
Copyright 2015-2016 Honeywell International Inc. All rights reserved.
Web Address: www.honeywellaidc.com
Microsoft® Windows®, Windows NT®, Windows 2000, Windows ME, Windows XP, and the Windows logo are trademarks or
registered trademarks of Microsoft Corporation.
The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc.
Apple is a trademark of Apple Inc., registered in the U.S. and other countries.
Other product names or marks mentioned in this document may be trademarks or registered trademarks of other companies
and are the property of their respective owners.
For patent information, refer to www.hsmpats.com.
Table of Contents
Customer Support
Technical Assistance ............................................................................................................ ix
Product Service and Repair .................................................................................................. ix
Limited Warranty ................................................................................................................... ix
Send Feedback ..................................................................................................................... ix
Chapter 1 - Getting Started
About This Manual ...............................................................................................................1-1
Unpacking Your Device .......................................................................................................1-1
Charging the Scanner Battery..............................................................................................1-1
Charging with a Power Supply .......................................................................................1-1
Charging with a PC ........................................................................................................1-2
Battery Charge Indicator ................................................................................................1-2
Pairing the Scanner with Bluetooth® Devices ......................................................................1-3
Pairing the Scanner with an Apple Device Using SPP...................................................1-4
Reading Techniques ............................................................................................................1-5
Menu Bar Code Security Settings ........................................................................................1-5
Setting Custom Defaults ......................................................................................................1-6
Resetting the Custom Defaults ............................................................................................1-6
Chapter 2 - Programming the Interface
Introduction ..........................................................................................................................2-1
Keyboard Country Layout ....................................................................................................2-1
Keyboard Style.....................................................................................................................2-8
Keyboard Conversion ..........................................................................................................2-9
Control Character Output ...................................................................................................2-10
Keyboard Modifiers ............................................................................................................2-10
Programming an Interface for an Access Point .................................................................2-12
Keyboard Wedge .........................................................................................................2-12
Laptop Direct Connect .................................................................................................2-12
RS232 Serial Port ........................................................................................................2-12
RS485 ..........................................................................................................................2-13
USB IBM SurePos........................................................................................................2-14
USB PC or Macintosh Keyboard..................................................................................2-14
USB HID.......................................................................................................................2-15
USB Serial....................................................................................................................2-15
Remote MasterMind™ for USB....................................................................................2-15
Gilbarco® Terminal Default Settings ............................................................................2-16
Honeywell Bioptic Aux Port Configuration....................................................................2-16
Datalogic™ Magellan® Aux Port Configuration............................................................2-16
NCR Bioptic Aux Port Configuration ............................................................................2-17
Wincor Nixdorf Terminal Default Settings ....................................................................2-17
Wincor Nixdorf Beetle™ Terminal Default Settings .....................................................2-17
Wincor Nixdorf RS232 Mode A ....................................................................................2-18
RS232 Modifiers...........................................................................................................2-18
Scanner to Bioptic Communication ..............................................................................2-22
i
Programming the VG1602 Corded Interface ..................................................................... 2-23
Setting the VG1602 Corded Interface.......................................................................... 2-23
Corded USB PC or Macintosh Keyboard..................................................................... 2-23
Corded USB HID POS................................................................................................. 2-23
Corded USB Serial ...................................................................................................... 2-24
Chapter 3 - Wireless System Operation
Bluetooth Settings ............................................................................................................... 3-1
Bluetooth HID Keyboard Disconnect ............................................................................. 3-1
Bluetooth Serial Port - PCs/Laptops .............................................................................. 3-1
PDAs/Mobility Systems Devices.................................................................................... 3-1
Changing the Scanner’s Bluetooth PIN Code................................................................ 3-1
Minimizing Bluetooth/ISM Band Network Activity ................................................................ 3-2
Auto Reconnect Mode ................................................................................................... 3-2
Maximum Link Attempts ................................................................................................ 3-2
Relink Time-Out............................................................................................................. 3-3
Bluetooth/ISM Network Activity Examples..................................................................... 3-3
Communication Between the Scanner and the Host........................................................... 3-4
Programming the Scanner and Host ................................................................................... 3-4
RF (Radio Frequency) Module Operation ........................................................................... 3-4
System Conditions............................................................................................................... 3-4
Scanner Is Out of Range ............................................................................................... 3-4
Scanner Is Moved Back Into Range .............................................................................. 3-4
Out of Range and Back into Range with Batch Mode On.............................................. 3-4
About the Battery................................................................................................................. 3-4
Charging Information ..................................................................................................... 3-5
Battery Recommendations ............................................................................................ 3-5
Proper Disposal of the Battery....................................................................................... 3-5
Beeper and LED Sequences and Meaning ......................................................................... 3-5
Scan LED Sequences and Meaning.............................................................................. 3-6
Low Battery Indicator ..................................................................................................... 3-6
Reset Scanner..................................................................................................................... 3-6
Scanner Report ................................................................................................................... 3-6
Scanner Address ................................................................................................................. 3-7
Linked Modes ...................................................................................................................... 3-7
Locked Link Mode - Single Scanner .............................................................................. 3-7
Open Link Mode - Single Scanner................................................................................. 3-7
Unlinking the Scanner.................................................................................................... 3-7
Override Locked Scanner .............................................................................................. 3-8
Out-of-Range Alarm ............................................................................................................ 3-8
Alarm Sound Type ......................................................................................................... 3-8
Scanner Idle Alarm .............................................................................................................. 3-9
Scanner Power Time-Out Timer.......................................................................................... 3-9
Flexible Power Management ............................................................................................. 3-10
Multiple Scanner Operation ............................................................................................... 3-10
Scanner Name................................................................................................................... 3-10
Application Work Groups................................................................................................... 3-12
Application Work Group Selection ............................................................................... 3-12
ii
Resetting the Factory Defaults: All Application Work Groups ........................................... 3-13
Resetting the Custom Defaults: All Application Work Groups ........................................... 3-13
Access Point Operations ................................................................................................... 3-13
Linking the Scanner to an Access Point ...................................................................... 3-13
Disconnect from Host and Connect to an Access Point .............................................. 3-14
Replacing a Linked Scanner........................................................................................ 3-14
Access Point LED Sequences and Meaning ..................................................................... 3-15
Access Point Address........................................................................................................ 3-15
Paging ............................................................................................................................... 3-15
Paging Mode................................................................................................................ 3-15
Paging Pitch................................................................................................................. 3-15
Batch Mode ....................................................................................................................... 3-16
Batch Mode Beep ........................................................................................................ 3-17
Batch Mode Storage .................................................................................................... 3-17
Batch Mode Quantity ................................................................................................... 3-17
Batch Mode Output Order............................................................................................ 3-19
Total Records .............................................................................................................. 3-19
Delete Last Code ......................................................................................................... 3-20
Clear All Codes............................................................................................................ 3-20
Transmit Records to Host ............................................................................................ 3-20
Batch Mode Transmit Delay ........................................................................................ 3-20
Host Acknowledgment....................................................................................................... 3-21
Host ACK Timeout ....................................................................................................... 3-22
Chapter 4 - Input/Output Settings
Programmable Button.......................................................................................................... 4-1
Virtual Keyboard ............................................................................................................ 4-1
Battery Charge Status ................................................................................................... 4-2
Flashlight Mode ............................................................................................................. 4-2
Bluetooth Pair/Unpair..................................................................................................... 4-3
Disable Programmable Button....................................................................................... 4-3
Power Up Beeper ................................................................................................................ 4-4
Beep on BEL Character....................................................................................................... 4-4
Trigger Click ........................................................................................................................ 4-4
Good Read and Error Indicators.......................................................................................... 4-5
Beeper – Good Read..................................................................................................... 4-5
Beeper Volume – Good Read........................................................................................ 4-5
Beeper Pitch – Good Read............................................................................................ 4-5
Beeper Pitch – Error ...................................................................................................... 4-6
Beeper Duration – Good Read ...................................................................................... 4-6
LED – Good Read ......................................................................................................... 4-6
Number of Beeps – Good Read .................................................................................... 4-7
Number of Beeps – Error............................................................................................... 4-7
Good Read Delay .......................................................................................................... 4-7
User-Specified Good Read Delay.................................................................................. 4-7
Manual Trigger Modes......................................................................................................... 4-8
Serial Trigger Mode ............................................................................................................. 4-8
Read Time-Out .............................................................................................................. 4-8
iii
Poor Quality Codes ............................................................................................................. 4-8
Poor Quality 1D Codes .................................................................................................. 4-8
Poor Quality PDF Codes ............................................................................................... 4-9
CodeGate® .......................................................................................................................... 4-9
Mobile Phone Read Mode ................................................................................................... 4-9
Character Activation Mode ................................................................................................ 4-10
Activation Character .................................................................................................... 4-10
End Character Activation After Good Read ................................................................. 4-10
Character Activation Timeout ...................................................................................... 4-11
Character Deactivation Mode ............................................................................................ 4-11
Deactivation Character ................................................................................................ 4-11
Illumination Lights.............................................................................................................. 4-11
Aimer Delay ....................................................................................................................... 4-12
User-Specified Aimer Delay......................................................................................... 4-12
Aimer Mode ....................................................................................................................... 4-12
Centering ........................................................................................................................... 4-12
Preferred Symbology......................................................................................................... 4-14
High Priority Symbology .............................................................................................. 4-14
Low Priority Symbology ............................................................................................... 4-14
Preferred Symbology Time-out.................................................................................... 4-15
Preferred Symbology Default....................................................................................... 4-15
Output Sequence Overview............................................................................................... 4-15
Output Sequence Editor .............................................................................................. 4-15
To Add an Output Sequence ....................................................................................... 4-15
Other Programming Selections.................................................................................... 4-16
Output Sequence Editor .............................................................................................. 4-17
Partial Sequence ......................................................................................................... 4-17
Require Output Sequence ........................................................................................... 4-17
Multiple Symbols ............................................................................................................... 4-18
No Read ............................................................................................................................ 4-18
Video Reverse ................................................................................................................... 4-19
Working Orientation........................................................................................................... 4-19
Chapter 5 - Data Editing
Prefix/Suffix Overview ......................................................................................................... 5-1
To Add a Prefix or Suffix:............................................................................................... 5-1
To Clear One or All Prefixes or Suffixes ........................................................................ 5-2
To Add a Carriage Return Suffix to All Symbologies ..................................................... 5-2
Prefix Selections.................................................................................................................. 5-2
Suffix Selections .................................................................................................................. 5-2
Function Code Transmit ...................................................................................................... 5-3
Intercharacter, Interfunction, and Intermessage Delays...................................................... 5-3
Intercharacter Delay ...................................................................................................... 5-3
User Specified Intercharacter Delay .............................................................................. 5-3
Interfunction Delay......................................................................................................... 5-4
Intermessage Delay....................................................................................................... 5-4
iv
Chapter 6 - Data Formatting
Data Format Editor Introduction .......................................................................................... 6-1
Add a Data Format .............................................................................................................. 6-1
Other Programming Selections...................................................................................... 6-2
Terminal ID Table ................................................................................................................ 6-3
Data Format Editor Commands........................................................................................... 6-3
Move Commands........................................................................................................... 6-5
Search Commands ........................................................................................................ 6-6
Miscellaneous Commands............................................................................................. 6-7
Data Formatter .................................................................................................................... 6-9
Data Format Non-Match Error Tone ............................................................................ 6-10
Primary/Alternate Data Formats ........................................................................................ 6-10
Single Scan Data Format Change ............................................................................... 6-10
Chapter 7 - Symbologies
All Symbologies ................................................................................................................... 7-1
Message Length Description ............................................................................................... 7-2
Codabar............................................................................................................................... 7-2
Codabar Concatenation................................................................................................. 7-3
Code 39 ............................................................................................................................... 7-4
Code 32 Pharmaceutical (PARAF) ................................................................................ 7-5
Full ASCII....................................................................................................................... 7-6
Code 39 Code Page ...................................................................................................... 7-6
Interleaved 2 of 5................................................................................................................. 7-7
NEC 2 of 5 ........................................................................................................................... 7-8
Code 93 ............................................................................................................................... 7-9
Code 93 Code Page .................................................................................................... 7-10
Straight 2 of 5 Industrial (three-bar start/stop)................................................................... 7-11
Straight 2 of 5 IATA (two-bar start/stop) ............................................................................ 7-12
Matrix 2 of 5....................................................................................................................... 7-13
Code 11 ............................................................................................................................. 7-14
Code 128 ........................................................................................................................... 7-15
ISBT 128 Concatenation.............................................................................................. 7-15
Code 128 Code Page .................................................................................................. 7-16
GS1-128 ............................................................................................................................ 7-17
Telepen.............................................................................................................................. 7-18
UPC-A ............................................................................................................................... 7-19
UPC-A/EAN-13 with Extended Coupon Code ................................................................... 7-21
Coupon GS1 DataBar Output............................................................................................ 7-21
UPC-E0 ............................................................................................................................. 7-22
UPC-E1 ............................................................................................................................. 7-24
EAN/JAN-13 ...................................................................................................................... 7-24
Convert UPC-A to EAN-13 .......................................................................................... 7-24
ISBN Translate ............................................................................................................ 7-26
EAN/JAN-8 ........................................................................................................................ 7-27
MSI .................................................................................................................................... 7-29
GS1 DataBar Omnidirectional ........................................................................................... 7-31
v
GS1 DataBar Limited......................................................................................................... 7-31
GS1 DataBar Expanded .................................................................................................... 7-32
Trioptic Code ..................................................................................................................... 7-32
Codablock A ...................................................................................................................... 7-33
Codablock F ...................................................................................................................... 7-34
Label Code ........................................................................................................................ 7-34
PDF417 ............................................................................................................................. 7-35
MacroPDF417 ................................................................................................................... 7-35
MicroPDF417..................................................................................................................... 7-36
GS1 Composite Codes...................................................................................................... 7-36
UPC/EAN Version........................................................................................................ 7-37
GS1 Emulation .................................................................................................................. 7-37
TCIF Linked Code 39 (TLC39) .......................................................................................... 7-38
QR Code............................................................................................................................ 7-38
QR Code Page ............................................................................................................ 7-39
Data Matrix ........................................................................................................................ 7-40
Data Matrix Code Page ............................................................................................... 7-40
MaxiCode .......................................................................................................................... 7-41
Aztec Code ........................................................................................................................ 7-42
Aztec Code Page......................................................................................................... 7-42
Chinese Sensible (Han Xin) Code..................................................................................... 7-43
Postal Codes - 2D ............................................................................................................. 7-44
Single 2D Postal Codes:.............................................................................................. 7-44
Combination 2D Postal Codes:.................................................................................... 7-45
Postal Codes - Linear ........................................................................................................ 7-48
China Post (Hong Kong 2 of 5).................................................................................... 7-48
Korea Post ................................................................................................................... 7-49
Chapter 8 - Utilities
To Add a Test Code I.D. Prefix to All Symbologies ............................................................. 8-1
Show Decoder Revision ...................................................................................................... 8-1
Show Scan Driver Revision ................................................................................................. 8-1
Show Software Revision...................................................................................................... 8-1
Show Data Format............................................................................................................... 8-1
Test Menu............................................................................................................................ 8-2
TotalFreedom ...................................................................................................................... 8-2
Application Plug-Ins (Apps) ................................................................................................. 8-2
EZConfig-Scanning Introduction.......................................................................................... 8-3
Installing EZConfig-Scanning from the Web.................................................................. 8-3
Resetting the Factory Defaults ............................................................................................ 8-4
Chapter 9 - Serial Programming Commands
Conventions......................................................................................................................... 9-1
Menu Command Syntax ...................................................................................................... 9-1
Query Commands ............................................................................................................... 9-1
Responses..................................................................................................................... 9-2
Trigger Commands.............................................................................................................. 9-3
vi
Resetting the Custom Defaults............................................................................................ 9-3
Menu Commands ................................................................................................................ 9-4
Chapter 10 - Product Specifications
Voyager 1602g Wireless Pocket Scanner Product Specifications .................................... 10-1
Standard Connector Pinout ............................................................................................... 10-3
Micro-B USB ................................................................................................................ 10-3
Chapter 11 - Maintenance and Troubleshooting
Repairs .............................................................................................................................. 11-1
Maintenance ...................................................................................................................... 11-1
Cleaning the Scanner .................................................................................................. 11-1
Cleaning the Window................................................................................................... 11-1
Inspecting Cords and Connectors ............................................................................... 11-1
Replacing a Battery ........................................................................................................... 11-2
Troubleshooting................................................................................................................. 11-3
Appendix A - Reference Charts
Symbology Charts ...............................................................................................................A-1
Linear Symbologies .......................................................................................................A-1
2D Symbologies.............................................................................................................A-2
Postal Symbologies .......................................................................................................A-2
ASCII Conversion Chart (Code Page 1252)........................................................................A-3
Lower ASCII Reference Table.............................................................................................A-4
ISO 2022/ISO 646 Character Replacements ......................................................................A-7
Keyboard Key Maps ..........................................................................................................A-10
Sample Symbols
Programming Chart
vii
viii
Customer Support
Technical Assistance
To search our knowledge base for a solution or to log in to the Technical Support portal and report a problem, go to
www.hsmcontactsupport.com.
For our latest contact information, see www.honeywellaidc.com/locations.
Product Service and Repair
Honeywell International Inc. provides service for all of its products through service centers throughout the world. To obtain
warranty or non-warranty service, please visit www.honeywellaidc.com and select Support > Contact Service and Repair
to see your region's instructions on how to obtain a Return Material Authorization number (RMA #). You should do this prior
to returning the product.
Limited Warranty
Refer to www.honeywellaidc.com/warranty_information for your product’s warranty information.
Send Feedback
Your feedback is crucial to the continual improvement of our documentation. To provide feedback about this manual, contact the Honeywell Technical Communications department at ACSHSMTechnicalCommunications@honeywell.com.
ix
x
1
Getting Started
About This Manual
This User’s Guide provides installation and programming instructions for the Voyager 1602g scanners. Product specifications,
dimensions, warranty, and customer support information are also included.
Note: The selections in this User’s Guide are dependent on the Voyager 1602g model you have purchased. PDF and 2
dimensional bar codes can only be read by model 1602g2D and cannot be read by model 1602g1D.
Honeywell bar code scanners are factory programmed for the most common terminal and communications settings. If you need
to change these settings, programming is accomplished by scanning the bar codes in this guide.
An asterisk (*) next to an option indicates the default setting.
Unpacking Your Device
After you open the shipping carton containing the product, take the following steps:
• Check for damage during shipment. Report damage immediately to the carrier who delivered the carton.
• Make sure the items in the carton match your order.
• Save the shipping container for later storage or shipping.
Charging the Scanner Battery
The scanner’s battery must be fully charged before the first use. It can be charged using a power supply or by connecting the
USB cable to a computer. Refer to About the Battery on page 3-4 for further battery information.
Charging with a Power Supply
Connect the mini-USB connector to the scanner. Assemble the wall plug. Attach the plug to the USB connector, then plug
into an electrical outlet, as shown below.
1-1
Charging with a PC
Charging your scanner battery through the USB port of a computer will take longer than charging with an electrical outlet.
Connect the mini-USB connector to the scanner and the USB connector to the computer, as shown below.
Note: The mini-USB connector is only used for charging the scanner. If using a scanner in corded mode, it can also be
used to configure the device via EZConfig (see page 8-3 for further information).
Battery Charge Indicator
When the battery is charging, the small LED at the top left of the scanner flashes orange. When the battery is fully
charged, this LED is solid green. Refer to Scan LED Sequences and Meaning (page 3-6) and Low Battery Indicator (page
3-6) for the complete list of LED indications.
To use your scanner with a Honeywell Access Point (AP01-XXXBT), refer to Host ACK Responses, page 3-22 or Linking the
Scanner to an Access Point, page 3-13.
1-2
Pairing the Scanner with Bluetooth® Devices
The scanner can be paired with Bluetooth devices such as personal computers, laptops, tablets, and Apple® devices.
1. Scan the appropriate Bluetooth Connect bar code below to establish one-way communication with the Voyager 1602g.
Bluetooth HID Keyboard
Connect
Bluetooth HID Japanese
Keyboard Connect
Note: If you want to use an Apple app or you are a developer creating an Apple app to communicate with the VG1602g, you
would use SPP to establish two-way communication to control the scanner through that application. See Pairing the
Scanner with an Apple Device Using SPP on page 1-4.
2. Set your personal computer, laptop, tablet, or Apple device so it searches for other Bluetooth devices. (Refer to your
device’s User’s Guide for pairing instructions.)
3. Once your personal computer, laptop, tablet, or Apple device has located the scanner, select the scanner name. Some
personal computers, laptops, or tablets will automatically pair with the scanner. If your device automatically pairs with the
scanner, it displays a successful pairing message and you do not need to continue to the next step.
4. If your personal computer, laptop, or tablet does not automatically pair with the scanner, a PIN is displayed. This PIN must
be scanned within 60 seconds. You must quickly scan Bluetooth PIN Code below, then scan the numeric bar code(s) for the
PIN code from the chart below, then scan the Save bar code.
Bluetooth PIN Code
0
1
2
3
1-3
4
5
6
7
8
9
Save
Your personal computer, laptop, tablet, or Apple device should now be paired with the scanner.
Once the scanner battery is charged and you have paired it, you may begin scanning bar codes. Verify the scanner operation
by scanning a bar code from the Sample Symbols in the back of this manual.
Pairing the Scanner with an Apple Device Using SPP
Serial port protocol, or SPP, is used to establish two-way Bluetooth communication with the scanner. If you want to use an
Apple app or you are a developer creating an Apple app to communicate with the VG1602, use SPP to control the scanner
through that application. This feature is only available with Apple's MFI-certified devices. Consult Apple to determine if
your device is MFI-certified. Scan the bar code below to pair the Voyager 1602g with an Apple device using SPP.
Pair with Apple Device
Using SPP
Once the Apple device is connected to the Voyager 1602g using SPP, you must select the app that will be used to send
commands to and receive responses from the scanner. To disconnect the association between the scanner and the app,
use Bluetooth HID Keyboard Disconnect on page 3-1.
1-4
Reading Techniques
The Voyager 1602g has a large scan button just forward of a smaller, programmable button. (See Programmable Button on
page 4-1 for further information about the programmable button.)
Scan button
Press the scan button to project an aiming beam. This beam should be centered over the bar code, but it can be positioned in
any direction for a good read.
Linear bar codes
with aiming beam
2D Matrix symbol
with aiming beam
The aiming beam is smaller when the scanner is closer to the code and larger when it is farther from the code. Symbologies
with smaller bars or elements (mil size) should be read closer to the scanner. Symbologies with larger bars or elements (mil
size) should be read farther from the scanner. To read single or multiple symbols (on a page or on an object), hold the scanner
at an appropriate distance from the target, press the scan button, and center the aiming beam on the symbol. If the code being
scanned is highly reflective (e.g., laminated), it may be necessary to tilt the code up 15° to 18° to prevent unwanted reflection.
Menu Bar Code Security Settings
Honeywell scanners are programmed by scanning menu bar codes or by sending serial commands to the scanner. If you want
to restrict the ability to scan menu codes, you can use the Menu Bar Code Security settings. Contact the nearest technical support office (see Technical Assistance on page -ix) for further information.
1-5
Setting Custom Defaults
You have the ability to create a set of menu commands as your own, custom defaults. To do so, scan the Set Custom Defaults
bar code below before scanning the menu commands for your custom defaults. If a menu command requires scanning numeric
codes from the back cover, then a Save code, that entire sequence will be saved to your custom defaults. When you have
entered all the commands you want to save for your custom defaults, scan the Save Custom Defaults bar code.
Set Custom Defaults
Save Custom Defaults
Note: The Custom Defaults settings apply to all workgroups Scanning the Save Defaults bar code also causes both the
scanner and the host to perform a reset and become unlinked. You must relink (pair) the scanner to the host. See
Wireless System Operation beginning on page 3-1 for additional information.
You may have a series of custom settings and want to correct a single setting. To do so, just scan the new setting to overwrite
the old one. For example, if you had previously saved the setting for Beeper Volume at Low to your custom defaults, and decide
you want the beeper volume set to High, just scan the Set Custom Defaults bar code, then scan the Beeper Volume High
menu code, and then Save Custom Defaults. The rest of the custom defaults will remain, but the beeper volume setting will be
updated.
Resetting the Custom Defaults
If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults bar code below. This is
the recommended default bar code for most users. It resets the scanner to the custom default settings. If there are no custom
defaults, it will reset the scanner to the factory default settings. Any settings that have not been specified through the custom
defaults will be defaulted to the factory default settings.
Activate Custom Defaults
Note: The Custom Defaults settings apply to all workgroups Scanning the Save Defaults bar code also causes both the
scanner and the host to perform a reset and become unlinked. You must relink (pair) the scanner to the host. See
Wireless System Operation beginning on page 3-1 for additional information.
1-6
2
Programming the Interface
Introduction
This chapter describes how to program your scanner for different keyboards and settings, and for an interface when using an
Access Point (see Programming an Interface for an Access Point, beginning on page 2-12). The VG1602g is primarily designed
as a cordless scanner. However, if you are using the VG1602g as a corded scanner, see Programming the VG1602 Corded
Interface beginning on page 2-23.
Keyboard Country Layout
If your interface is USB Keyboard or Keyboard Wedge through an Access Point, or a Bluetooth Keyboard, your keyboard layout
default is a US keyboard. To change this layout, refer to the chart below for your keyboard country. Scan the appropriate bar
code below to change the layout.
By default, national character replacements are used for the following characters: #$@[\]^‘{|}~ See ISO 2022/ISO 646
Character Replacements on page A-7 to view the character replacements for each country.
Keyboard Countries
* United States
Albania
Azeri (Cyrillic)
Azeri (Latin)
Belarus
Belgium
Bosnia
Brazil
2-1
Keyboard Countries (Continued)
Brazil (MS)
Bulgaria (Cyrillic)
Bulgaria (Latin)
Canada (French legacy)
Canada (French)
Canada (Multilingual)
Croatia
Czech
Czech (Programmers)
Czech (QWERTY)
Czech (QWERTZ)
2-2
Keyboard Countries (Continued)
Denmark
Dutch (Netherlands)
Estonia
Faroese
Finland
France
Gaelic
Germany
Greek
Greek (220 Latin)
Greek (220)
2-3
Keyboard Countries (Continued)
Greek (319 Latin)
Greek (319)
Greek (Latin)
Greek (MS)
Greek (Polytonic)
Hebrew
Hungarian (101 key)
Hungary
Iceland
Irish
Italian (142)
2-4
Keyboard Countries (Continued)
Italy
Japan ASCII
Kazakh
Kyrgyz (Cyrillic)
Latin America
Latvia
Latvia (QWERTY)
Lithuania
Lithuania (IBM)
Macedonia
Malta
2-5
Keyboard Countries (Continued)
Mongolian (Cyrillic)
Norway
Poland
Polish (214)
Polish (Programmers)
Portugal
Romania
Russia
Russian (MS)
Russian (Typewriter)
SCS
2-6
Keyboard Countries (Continued)
Serbia (Cyrillic)
Serbia (Latin)
Slovakia
Slovakia (QWERTY)
Slovakia (QWERTZ)
Slovenia
Spain
Spanish variation
Sweden
Switzerland (French)
Switzerland (German)
2-7
Keyboard Countries (Continued)
Tatar
Turkey F
Turkey Q
Ukrainian
United Kingdom
United States (Dvorak)
United States (Dvorak left)
United Stated (Dvorak right)
United States (International)
Uzbek (Cyrillic)
Keyboard Style
This programs keyboard styles, such as Caps Lock and Shift Lock. If you have used Keyboard Conversion settings, they will
override any of the following Keyboard Style settings. Default = Regular.
2-8
Regular is used when you normally have the Caps Lock key off.
* Regular
Caps Lock is used when you normally have the Caps Lock key on.
Caps Lock
Shift Lock is used when you normally have the Shift Lock key on (not common to U.S. keyboards).
Shift Lock
Automatic Caps Lock is used if you change the Caps Lock key on and off. The software tracks and reflects if you have Caps
Lock on or off . This selection can only be used with systems that have an LED that notes the Caps Lock status (AT keyboards).
Automatic Caps Lock
Autocaps via NumLock bar code should be scanned in countries (e.g., Germany, France) where the Caps Lock key cannot be
used to toggle Caps Lock. The NumLock option works similarly to the regular Autocaps, but uses the NumLock key to retrieve
the current state of the Caps Lock.
Autocaps via NumLock
Emulate External Keyboard should be scanned if you do not have an external keyboard (IBM AT or equivalent).
Emulate External Keyboard
Note: After scanning the Emulate External Keyboard bar code, you must power cycle the host system.
Keyboard Conversion
Alphabetic keyboard characters can be forced to be all upper case or all lowercase. So if you have the following bar code:
“abc569GK,” you can make the output “ABC569GK” by scanning Convert All Characters to Upper Case, or to “abc569gk” by
scanning Convert All Characters to Lower Case.
These settings override Keyboard Style selections.
Note: If your interface is a keyboard wedge, first scan the menu code for Automatic Caps Lock (page 2-9). Otherwise, your
output may not be as expected.
2-9
Default = Keyboard Conversion Off.
* Keyboard Conversion Off
Convert All Characters
to Upper Case
Convert All Characters
to Lower Case
Control Character Output
This selection sends a text string instead of a control character. For example, when the control character for a carriage return is
expected, the output would display [CR] instead of the ASCII code of 0D. Refer to ASCII Conversion Chart (Code Page
1252) on page A-3. Only codes 00 through 1F are converted (the first column of the chart). Default = Off.
Note: Control + X (Control + ASCII) Mode overrides this mode.
Control Character Output On
* Control Character Output Off
Keyboard Modifiers
This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo Mode.
Control + X (Control + ASCII) Mode On: The scanner sends key combinations for ASCII control characters for values 00-1F.
Windows is the preferred mode. All keyboard country codes are supported. DOS mode is a legacy mode, and it does not support all keyboard country codes. New users should use the Windows mode. Refer to ASCII Conversion Chart (Code Page
1252), page A-3 for CTRL+ X Values.
Windows Mode Prefix/Suffix Off: The scanner sends key combinations for ASCII control characters for values 00-1F, but it
does not translate prefix or suffix information.
Default = Control + X Mode Off.
Windows Mode Control + X
Mode On
2 - 10
* Control + X Mode Off
DOS Mode Control + X Mode On
Windows Mode Prefix/Suffix Off
Turbo Mode: The scanner sends characters to a terminal faster. If the terminal drops characters, do not use Turbo Mode.
Default = Off.
Turbo Mode On
* Turbo Mode Off
Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off.
Numeric Keypad Mode On
* Numeric Keypad Mode Off
Automatic Direct Connect Mode: This selection can be used if you have an IBM AT style terminal and the system is dropping
characters. Default = Off.
Automatic Direct Connect Mode
On
* Automatic Direct Connect
Mode Off
2 - 11
Programming an Interface for an Access Point
If you are using a Honeywell Access Point (AP01-XXXBT) to communicate with the VG1602, you can use the following bar
codes to program the Access Point interface. These bar codes set the Access Point for commonly used interfaces.
Keyboard Wedge
If you want your system programmed for an IBM PC AT and compatibles keyboard wedge interface with a USA keyboard,
scan the bar code below, then power cycle the host. Keyboard wedge is the default interface. This interface is only appropriate for an Access Point.
Note: The following bar code also programs a carriage return (CR) suffix.
IBM PC AT and Compatibles with
CR suffix
Laptop Direct Connect
For most laptops, scanning the Laptop Direct Connect bar code allows operation of the scanner in parallel with the integral keyboard. The following Laptop Direct Connect bar code also programs a carriage return (CR) suffix and turns on
Emulate External Keyboard (page 2-9). Power cycle the host after scanning this bar code. This interface is only appropriate for an Access Point.
Laptop Direct Connect
with CR suffix
RS232 Serial Port
The RS232 Interface bar code is used when connecting to the serial port of a PC or terminal. The following RS232 Interface bar code also programs a carriage return (CR) and a line feed (LF) suffix, baud rate, and data format as indicated
below. It also changes the trigger mode to manual. This interface is only appropriate for an Access Point.
Option
Setting
Baud Rate
Data Format
115,200 bps
8 data bits, no parity bit, 1 stop bit
RS232 Interface
2 - 12
RS485
Scan one of the following “Plug and Play” codes to program the scanner for an IBM POS terminal interface. This interface
is only appropriate for an Access Point.
Note: After scanning one of these codes, you must power cycle the cash register.
IBM Port 5B Interface
IBM Port 9B
HHBCR-1 Interface
IBM Port 17 Interface
IBM Port 9B
HHBCR-2 Interface
Each bar code above also programs the following suffixes for each symbology:
Symbology
Suffix
Symbology
Suffix
EAN 8
EAN 13
UPC A
UPC E
0C
16
0D
0A
Code 39
Interleaved 2 of 5
Code 128 *
Code 128 **
MaxiCode
00
00
00
00
00
0A
0D
0A
18
2F
0B
0B
0B
0B
0B
* Suffixes programmed for Code 128 with IBM 4683 Port 5B, IBM 4683 Port 9B HHBCR-1, and IBM 4683 Port 17 Interfaces
**Suffixes programmed for Code 128 with IBM 4683 Port 9 HHBCR-2 Interface
RS485 Packet Mode
The following selection allows you to break up large bar code data into smaller packets on an IBM POS terminal. To
break up large bar codes into small packets, scan the Packet Mode On bar code below. Scan the Packet Mode Off
bar code if you want large bar code data to be sent to the host in a single chunk. Default = Packet Mode Off.
* Packet Mode Off
Packet Mode On
2 - 13
RS485 Packet Length
If you are using Packet mode, you can specify the size of the data “packet” that is sent to the host. Scan the Packet
Length bar code, then then the packet size (from 20 - 256) from the Programming Chart inside the back cover of this
manual, then Save. Default = 40.
Packet Length
USB IBM SurePos
Scan one of the following “Plug and Play” codes to program the scanner for an IBM SurePos (USB handheld scanner) or
IBM SurePos (USB tabletop scanner) interface. This interface is only appropriate for an Access Point.
Note: After scanning one of these codes, you must power cycle the cash register.
USB IBM SurePos
(USB Handheld Scanner)
Interface
USB IBM SurePos
(USB Tabletop Scanner)
Interface
Each bar code above also programs the following suffixes for each symbology:
Symbology
Suffix
Symbology
Suffix
EAN 8
EAN 13
UPC A
UPC E
0C
16
0D
0A
Code 39
Interleaved 2 of 5
Code 128
Code 39
00
00
00
00
0A
0D
18
0A
0B
0B
0B
0B
USB PC or Macintosh Keyboard
Scan one of the following codes to program the scanner for USB PC Keyboard or USB Macintosh Keyboard, then power
cycle the host. Scanning these codes also adds a CR suffix. This interface is only appropriate for an Access Point.
USB Keyboard (PC)
USB Keyboard (Mac)
USB Japanese Keyboard (PC)
2 - 14
USB HID
Scan the following code to program the scanner for USB HID bar code scanners, then power cycle the host. This interface
is only appropriate for an Access Point.
USB HID Bar Code Scanner
USB Serial
This interface is only appropriate for an Access Point. Scan the following code to program the scanner to emulate a regular
RS232-based COM Port, then power cycle the host. If you are using a Microsoft® Windows® PC, you will need to download a driver from the Honeywell website (www.honeywellaidc.com). The driver will use the next available COM Port number. Apple® Macintosh computers recognize the scanner as a USB CDC class device and automatically use a class driver.
USB Serial
Note: No extra configuration (e.g., baud rate) is necessary.
CTS/RTS Emulation
CTS/RTS Emulation On
* CTS/RTS Emulation Off
ACK/NAK Mode
ACK/NAK Mode On
* ACK/NAK Mode Off
Remote MasterMind™ for USB
When using a USB interface, you may wish to configure your scanner to communicate with Remote MasterMind Scanner
Management Software (ReM). Scan the ReM On bar code to communicate with ReM. To disable this capability, scan ReM
Off. This interface is only appropriate for an Access Point.
ReM Off
2 - 15
ReM On
Gilbarco® Terminal Default Settings
This interface is only appropriate for an Access Point. Scan the following Plug and Play code to program the scanner for a
Gilbarco terminal, then power cycle the host. This bar code sets the baud rate to 2400 bps and the data format to 7 data
bits, even parity, 2 stop bits. It also adds a carriage return (CR) suffix and programs the following prefixes for each symbology:
Symbology
Prefix
UPC-A
UPC-E
EAN-8
EAN-13
A
E0
FF
F
Gilbarco Settings
Honeywell Bioptic Aux Port Configuration
This interface is only appropriate for an Access Point. Scan the following Plug and Play code to program the scanner for a
Honeywell bioptic scanner auxiliary port configuration, then power cycle the host. This bar code sets the baud rate to
38400 bps and the data format to 8 data bits, no parity, 1 stop bit.
Honeywell Bioptic Settings
Datalogic™ Magellan® Aux Port Configuration
This interface is only appropriate for an Access Point. Scan the following Plug and Play code to program the scanner for a
Datalogic Magellan auxiliary port configuration, then power cycle the host. This bar code sets the baud rate to 9600 bps
and the data format to 8 data bits, no parity, 1 stop bit.
Datalogic Magellan Settings
2 - 16
NCR Bioptic Aux Port Configuration
This interface is only appropriate for an Access Point. Scan the following Plug and Play code to program the scanner for an
NCR bioptic scanner auxiliary port configuration, then power cycle the host. The following prefixes are programmed for
each symbology:
Symbology
Prefix
Symbology
Prefix
UPC-A
UPC-E
A
E0
b
f
a
EAN-8
EAN-13
FF
F
Interleaved 2 of 5
Code 128
Code 32
Pharmaceutical
(PARAF)
Code 39
a
NCR Bioptic Settings
Wincor Nixdorf Terminal Default Settings
This interface is only appropriate for an Access Point. Scan the following Plug and Play code to program the scanner for a
Wincor Nixdorf terminal, then power cycle the host. This bar code sets the baud rate to 9600 bps and the data format to 8
data bits, no parity, 1 stop bit.
Wincor Nixdorf Terminal Settings
Wincor Nixdorf Beetle™ Terminal Default Settings
This interface is only appropriate for an Access Point. Scan the following Plug and Play code to program the scanner for a
Wincor Nixdorf Beetle terminal, then power cycle the host. The following prefixes are programmed for each symbology:
Symbology
Prefix
Aztec Code
Codabar
Code 93
Code 128
Data Matrix
EAN-8
EAN-13
GS1 DataBar
GS1-128
V
N
L
K
R
B
A
E
P
Symbology
Interleaved 2 of 5
MaxiCode
MicroPDF417
PDF417
QR Code
Straight 2 of 5 IATA
UPC-A
UPC-E
All other bar codes
Prefix
I
T
S
Q
U
H
A0
C
M
Wincor Nixdorf Beetle Settings
2 - 17
Wincor Nixdorf RS232 Mode A
This interface is only appropriate for an Access Point. Scan the following Plug and Play code to program the scanner for a
Wincor Nixdorf RS232 Mode A terminal, then power cycle the host. This bar code sets the baud rate to 9600 bps and the
data format to 8 data bits, odd parity, 1 stop bit. The following prefixes are programmed for each symbology:
Wincor Nixdorf RS232 Mode A
Settings
RS232 Modifiers
The following RS232 settings should only be used when connecting through an Access Point.
RS232 Baud Rate
Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the
same baud rate as the scanner. Default = 115,200.
300
600
1200
2400
4800
9600
19200
2 - 18
38400
57,600
* 115,200
RS232 Word Length: Data Bits, Stop Bits, and Parity
Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters
0 through 7F decimal (text, digits, and punctuation), select 7 data bits. For applications that require use of the full
ASCII set, select 8 data bits per character. Default = 8.
Stop Bits sets the stop bits at 1 or 2. Default = 1.
Parity provides a means of checking character bit patterns for validity.
Default = None.
7 Data, 1 Stop, Parity Even
7 Data, 1 Stop, Parity None
7 Data, 1 Stop, Parity Odd
7 Data, 2 Stop, Parity Even
7 Data, 2 Stop Parity None
7 Data, 2 Stop, Parity Odd
8 Data, 1 Stop, Parity Even
2 - 19
* 8 Data, 1 Stop, Parity None
8 Data, 1 Stop, Parity Odd
8 Data, 1 Stop, Parity Mark
RS232 Receiver Time-Out
The unit stays awake to receive data until the RS232 Receiver Time-Out expires. A scan button push or serial trigger
command resets the time-out. When an RS232 receiver is sleeping, a character may be sent to wake up the receiver
and reset the time-out. A transaction on the CTS line will also wake up the receiver. The receiver takes 300 milliseconds to completely come up. Change the RS232 receiver time-out by scanning the bar code below, then scanning digits from the inside back cover of this manual, then scanning Save. The range is 0 to 300 seconds. Default = 0
seconds (no time-out - always on).
RS232 Receiver Time-Out
RS232 Handshaking
RS232 Handshaking allows control of data transmission from the scanner using software commands from the host
device. When RTS/CTS is turned Off, no data flow control is used.
Flow Control, No Timeout: The scanner asserts RTS when it has data to send, and will wait indefinitely for CTS to be
asserted by the host.
Two-Direction Flow Control: The scanner asserts RTS when it is OK for the host to transmit. The host asserts CTS
when it is OK for the device to transmit.
Flow Control with Timeout: The scanner asserts RTS when it has data to send and waits for a delay (see RS232
Timeout on page 2-21) for CTS to be asserted by the host. If the delay time expires and CTS is not asserted, the
device transmit buffer is cleared and scanning may resume. Default = RTS/CTS Off.
Flow Control, No Timeout
Two-Direction Flow Control
Flow Control with Timeout
2 - 20
* RTS/CTS Off
RS232 Timeout
When using Flow Control with Timeout, you must program the length of the delay you want to wait for CTS from the
host. Set the length (in milliseconds) for a timeout by scanning the bar code below, then setting the timeout (from 15100 milliseconds) by scanning digits from the inside back cover, then scanning Save.
RS232 Timeout
XON/XOFF
Standard ASCII control characters can be used to tell the scanner to start sending data (XON/XOFF On) or to stop
sending data (XON/XOFF Off). When the host sends the XOFF character (DC3, hex 13) to the scanner, data transmission stops. To resume transmission, the host sends the XON character (DC1, hex 11). Data transmission continues where it left off when XOFF was sent. Default = XON/XOFF Off.
XON/XOFF On
* XON/XOFF Off
ACK/NAK
After transmitting data, the scanner waits for an ACK character (hex 06) or a NAK character (hex 15) response from
the host. If ACK is received, the communications cycle is completed and the scanner looks for more bar codes. If NAK
is received, the last set of bar code data is retransmitted and the scanner waits for ACK/NAK again. Turn on the ACK/
NAK protocol by scanning the ACK/NAK On bar code below. To turn off the protocol, scan ACK/NAK Off. Default =
ACK/NAK Off.
ACK/NAK On
* ACK/NAK Off
2 - 21
Scanner to Bioptic Communication
The following Scanner to Bioptic Communication settings should only be used when connecting through an Access Point.
They are used to set up communication between Honeywell scanners and bioptic scanners.
Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate
with a bioptic scanner. See "RS232 Modifiers" on page 2-18, and RS232 Timeout on page 2-21 for further
information.
Scanner-Bioptic Packet Mode
Packet Mode On must be scanned to set the scanner’s format so it is compatible with a bioptic scanner. Default =
Packet Mode Off.
* Packet Mode Off
Packet Mode On
Scanner-Bioptic ACK/NAK Mode
Bioptic ACK/NAK On must be scanned so the scanner will wait for an ACK or NAK from a bioptic scanner after each
packet is sent. The Scanner-Bioptic ACK/NAK Timeout (below) controls how long the scanner will wait for a response.
Default = Bioptic ACK/NAK Off.
* Bioptic ACK/NAK Off
Bioptic ACK/NAK On
Scanner-Bioptic ACK/NAK Timeout
This allows you to set the length (in milliseconds) for a timeout for a bioptic scanner’s ACK/NAK response. Scan the
bar code below, then set the timeout (from 1-30,000 milliseconds) by scanning digits from the inside back cover, then
scanning Save. Default = 5100.
ACK/NAK Timeout
2 - 22
Programming the VG1602 Corded Interface
You may convert a VG1602 scanner to a corded scanner using a USB interface cable. Use the following bar codes to program
the VG1602g as a corded scanner.
Setting the VG1602 Corded Interface
Scan one of the following codes to set the scanner’s communication as either Bluetooth, for a cordless scanner, to USB, for
a corded scanner. Default = Bluetooth Communication (Cordless Scanner).
Note: Once the communication is set to USB (Corded Scanner), the VG1602g can only communicate with the host via a
USB interface cable.
USB Communication
(Corded Scanner)
* Bluetooth Communication
(Cordless Scanner)
Corded USB PC or Macintosh Keyboard
Scan one of the following codes to program the corded scanner for a USB Keyboard, either PC or Macintosh, then power
cycle the host.
Corded USB Keyboard (PC)
Corded USB Keyboard (Mac)
Corded USB HID POS
Scan the following code to program the corded scanner for USB HID POS interface, then power cycle the host.
Corded USB HID POS Interface
2 - 23
Corded USB Serial
Scan the following code to program the corded scanner to emulate a regular RS232-based COM Port, then power cycle the
host. If you are using a Microsoft® Windows® PC, you will need to download a driver from the Honeywell website
(www.honeywellaidc.com). The driver will use the next available COM Port number. Apple® Macintosh computers recognize the scanner as a USB CDC class device and automatically use a class driver.
Corded USB Serial
Note: No extra configuration (e.g., baud rate) is necessary.
Corded CTS/RTS Emulation
Corded CTS/RTS Emulation On
* Corded CTS/RTS Emulation
Off
Corded ACK/NAK Mode
Corded ACK/NAK Mode On
* Corded ACK/NAK Mode Off
2 - 24
3
Wireless System Operation
The VG1602g scanner can be used with Bluetooth devices such as personal computers, laptops, PDAs, and Honeywell mobility
systems devices.
Bluetooth Settings
Refer to Pairing the Scanner with Bluetooth® Devices, beginning on page 1-3, to link your scanner to a host via Bluetooth. The
following settings allow you to refine your Bluetooth connection.
Bluetooth HID Keyboard Disconnect
If your scanner has been connected directly to an iPad, smart phone, or laptop, you must disconnect it in order to communicate with a new host. Scan the Bluetooth HID Keyboard Disconnect bar code to unlink the scanner from the currently
linked host. Following the appropriate linking or pairing procedure to link the scanner to the new host.
Bluetooth HID Keyboard Disconnect
Bluetooth Serial Port - PCs/Laptops
Scanning the Non-Base BT Connection bar code below unlinks your scanner and puts it into a discoverable state. Once
the scanner searches for and connects with a Bluetooth host, the scanner stores the connection to the host device address
and switches virtual COM ports. This allows the scanner to automatically relink to the host if the connection is lost.
Non-Base BT Connection
PDAs/Mobility Systems Devices
You may also use the scanner with a PDA or a Honeywell Mobility Systems device. Scan the bar code below and follow the
instructions supplied with your Bluetooth device to locate and pair with the scanner.
BT Connection - PDA/Mobility Systems Device
Changing the Scanner’s Bluetooth PIN Code
Some devices require a PIN code as part of the Bluetooth security features. Your scanner’s default PIN is 1234, which you
may need to enter the first time you connect to your host. The PIN code must be between 1 and 16 characters. To change
the PIN for your scanner, scan the bar code below and then scan the appropriate numeric bar codes from the Programming
Chart inside the back cover of this manual. Scan Save to save your selection.
Bluetooth PIN
3-1
Minimizing Bluetooth/ISM Band Network Activity
The settings described below can help you customize the relinking behavior of the wireless area-imaging system to obtain the
best compromise between convenience and low interference.
Note: ISM band refers to the 2.4 to 2.48 GHz frequency band used by wireless networks, cordless phones, and Bluetooth.
Auto Reconnect Mode
Auto Reconnect controls whether or not the scanner automatically begins the relink process when a loss of connection is
detected. When the Auto Reconnect On bar code is scanned, the scanner begins the relink process immediately, without
user intervention. Default = Auto Reconnect On.
* Auto Reconnect On
Auto Reconnect Off
Note: If you are connecting to a Bluetooth Interface Module, set Auto Reconnect to Off.
The table below shows the results of the Auto Reconnect On and Off settings:
Event
Auto Reconnect On
Auto Reconnect Off
Scanner out of range
Relink occurs automatically. If maximum
number of link attempts is unsuccessful,
then the scanner must be relinked by
either pressing the scan button or
relinking the scanner to the host. See
Pairing the Scanner
with Bluetooth® Devices on page 1-3.
Also see Maximum Link Attempts on
page 3-2.
The scanner is relinked by pressing
the scan button or relinking to the
host.
Host reset (firmware upgrade or
power cycle)
Scanner behaves as if out of range.
No attempt to relink made while host
is powered off. Scan button must be
pressed to initiate relinking.
Scanner power down due to
Power Time-Out Timer setting
(see page 3-9)
Scan button must be pressed.
Scanner reset due to firmware
upgrade
Relink occurs automatically.
Scanner reset due to battery
change
Relink occurs automatically.
Maximum Link Attempts
The Maximum Link Attempts setting controls the number of times the scanner tries to form a connection with a host.
During the connection setup process, the scanner transmits in order to search for and connect to a host. In order to prevent
continuous transmissions that could interfere with other users of the ISM band, the number of attempts to connect is limited
by this setting. After the maximum number of attempts is reached, the scanner will not attempt to reconnect to a host.
Pressing the scan button, scanning a host linking bar code, or pairing the scanner with a host resets the attempt count and
the scanner will again try to link.
3-2
Scan the Maximum Link Attempts bar code, then scan the number of attempts for the setting (from 0-100) from the inside
back cover. Scan Save to save the setting. Default = 0.
Maximum Link Attempts
Note: When Auto Reconnect Mode is On, setting Maximum Link Attempts to zero will cause the scanner to try to link until
the Power Time-Out Timer setting (see page 3-9) expires. When Auto Reconnect Mode is Off, setting Maximum Link
Attempts to zero will cause the scanner to only attempt linking one time after a scan button press.
Relink Time-Out
Relink Time-Out controls the idle time between relink attempts. An attempt to link a scanner to a host typically lasts up to 5
seconds. This is the time when the scanner is actually attempting a contact . Relink Time-Out controls the amount of time,
in seconds, that elapses between the end of one connection attempt and the start of the next.
Note: The length of time for an attempt depends on the number of scanners connected to a host. An extra 7 seconds may
be required when a connection is successful.
Scan the Relink Time-Out bar code, then scan the number of seconds for the setting (from 1-100) from the inside back
cover. Scan Save to save the setting. Default = 3 seconds.
Relink Time-Out
Bluetooth/ISM Network Activity Examples
Note: See Batch Mode on page 3-16 for information about using Batch Mode.
Default values
When the scanner goes out of range, the scanner repeatedly attempts to connect to the host. Each attempt consists of
approximately 5 seconds of active time followed by 3 seconds of idle time. After one hour, the scanner powers off and
batch mode data is lost.
Maximum Link Attempts set to 15
Other values at default setting
When the scanner goes out of range, 15 attempts are made to link to the host. Each attempt consists of approximately 5
seconds of active time followed by 3 seconds of idle time. After 15 cycles (8*15 =120), or about 2 minutes, the scanner
stops trying to connect to the host, but retains any bar codes that may have been saved in batch mode. After one hour, the
scanner powers off and batch mode data is lost.
Auto Reconnect Mode set to 0
Maximum Link Attempts set to 15
Other values at default setting
When the scanner goes out of range, no action is taken to relink. When the scan button is pressed, 15 attempts are made
to link to the host. Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time.
After 15 cycles (8*15 =120), or about 2 minutes, the scanner stops trying to connect to the host, but retains any bar codes
that may have been saved in batch mode. After one hour, the scanner powers off and batch mode data is lost. Refer to
Auto Reconnect Mode, page 3-2, to review other events that can start the relink process.
Auto Reconnect Mode set to 1
Maximum Link Attempts set to 0
Relink Time-Out set to 10
Scanner Power Time-Out Timer set to 1800
Note: See Scanner Power Time-Out Timer on page 3-9.
3-3
The scanner attempts to connect to the host every 15 seconds, measured from one attempt start to the next attempt start.
After one half hour, the scanner powers off.
Communication Between the Scanner and the Host
When data is scanned, the data is sent to the host system. The wireless scanner provides immediate feedback in the form of a
“good read” indication with a green LED on the scanner and an audible beep. This indicates only that the bar code has been
scanned correctly.
When using an Access Point, the host also acknowledges when it has received the data. The wireless scanner recognizes data
acknowledgment (ACK) from the host. If an Access Point cannot determine that the data has been properly sent to the host, the
scanner issues an error tone. You must then check to see if the scanned data was received by the host.
Programming the Scanner and Host
When using the scanner and host together as a system, menu parameters and configuration settings are stored in the host. If
the scanner is not linked to a host, configuration settings are stored in the scanner.
RF (Radio Frequency) Module Operation
The wireless system uses a two-way Bluetooth® radio utilizing adaptive frequency hopping (APH) to transmit and receive data
between the scanner and the host. Designed for point-to-point and multiple point-to-single-point applications, the radio operates using a license-free ISM band, which sends relatively small data packets at a fast data rate over a radio signal with randomly changing frequencies. This makes the wireless system highly responsive to a wide variety of data collection applications
and resistant to noisy RF environments. The communication range between the scanner and host, depending on the environment, is 33 feet (10m). See Flexible Power Management, page 3-10, for information about controlling this range.
System Conditions
The components of the wireless system interact in specific ways as you move a scanner out of range, bring a scanner back in
range, or swap scanners between two hosts. The following information explains the wireless system operating conditions.
Scanner Is Out of Range
The wireless scanner is in communication with its host, even when it is not transmitting bar code data. Whenever the scanner can’t communicate with the host for a few seconds, it is out of range. If the scanner is out of range and you scan a bar
code, the scanner issues an error tone indicating that there was no communication with the host. Refer to Out-of-Range
Alarm, page 3-8 and Auto Reconnect Mode, page 3-2.
Scanner Is Moved Back Into Range
The scanner relinks if the scanner or the host have been reset, or the scanner comes back into range. If the scanner
relinks, you will hear a single chirp when the relinking process (uploading of the parameter table) is complete. Refer to Outof-Range Alarm on page 3-8 and Auto Reconnect Mode, page 3-2 for further information.
Out of Range and Back into Range with Batch Mode On
Note: See Batch Mode, beginning on page 3-16, for further information.
The scanner may store a number of symbols (approximately 500 U.P.C. symbols; others may vary) when it is out of range
and then send them to the host when back in range.
You will not hear a communication error tone in this mode, but you will hear a short buzz when you press the scan button if
the radio communication is not working. Once the radio connection is made, the scanner produces a series of beeps while
the data is being transferred to the host.
About the Battery
!
3-4
There is a danger of explosion if the batteries are incorrectly replaced. Replace the batteries with only the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to the recycle program for
batteries as directed by the governing agency for the country where the batteries are to be discarded.
Power is supplied to the wireless scanner by a rechargeable battery that is integrated in the scanner. Batteries are not shipped
fully charged. The battery should be charged for a minimum of 4 hours before initial use to ensure optimal performance.
Charging Information
The battery is designed to charge while the scanner is plugged into a wall outlet or into a host via the USB cable. Refer to
Low Battery Indicator, page 3-6, for an interpretation of the Charge Status indicators.
Plug the scanner in a Listed Limited Power Source (LPS) or Class 2 type power supply with output rated 5 to 5.2Vdc, 1A.
Note: If you are powering the scanner through the USB interface cable instead of using an external power supply, the
current available for charging is reduced and charge times are increased.
Battery Recommendations
• The battery is a lithium ion cell and can be used without a full charge, and can also be charged without fully discharging,
without impacting the battery life. There is no need to perform any charge/discharge conditioning on this type of battery.
• Replace a defective battery immediately since it could damage the scanner.
• Although your battery can be recharged many times, it will eventually be depleted. Replace it after the battery is unable
to hold an adequate charge.
• If you are not sure if the battery or charger is working properly, send it to Honeywell International Inc. or an authorized
service center for inspection. Refer to Customer Support on page -ix for additional information.
!
Caution:
Use only Honeywell Li-ion battery packs, part number 3H21-00000112, or 163480-0001, rated 3.7 Vdc,
2.77Whr in this device. Use of any non-Honeywell battery may result in damage not covered by the warranty.
Safety Precautions for Lithium Batteries
•
•
•
•
•
•
•
Do not place batteries in fire or heat the batteries.
Do not store batteries near fire or other high temperature locations.
Do not store or carry batteries together with metal objects.
Do not expose batteries to water or allow the batteries to get wet.
Do not connect (short) the positive and negative terminals, of the batteries, to each other with any metal object.
Do not pierce, strike or step on batteries or subject batteries to strong impacts or shocks.
Do not disassemble or modify batteries.
!
Caution:
Danger of explosion if batteries are incorrectly replaced. Dispose of used batteries according to the recycle
program for batteries as directed by the governing agency for the country where the batteries are to be
discarded.
Proper Disposal of the Battery
When the battery has reached the end of its useful life, the battery should be disposed of by a qualified
recycler or hazardous materials handler. Do not incinerate the battery or dispose of the battery with general waste materials. You may send the scanner’s battery to us. (postage paid). The shipper is responsible for complying with all federal, state, and local laws and regulations related to the packing, labeling,
manifesting, and shipping of spent batteries. Contact the Product Service and Repair (page -ix) for recycling or disposal information. Since you may find that your cost of returning the batteries significant, it
may be more cost effective to locate a local recycle/disposal company.
Beeper and LED Sequences and Meaning
The scanner contains 2 LEDs on the top of the unit that indicate linking status, decoding state, and battery condition. There are
audible indicators as well: 1 razz or error tone = error; 2 beeps = menu change; 1 beep = all other successes.
The table below lists the indication and cause of the LED indicators and beeps for the scanner.
3-5
Scan LED Sequences and Meaning
LED Indication
Beeper Indication
Cause
Normal Operation
Red flash
Green flash
Red, blinking
Blue, off
None
1 beep
Razz or error tone
None
Blue flash
None
Blue, on
Menu Operation
Green flash
Red, blinking
1 beep
Battery low
Successful scan
Failed communication
Bluetooth connection has not been
established
Scanner is attempting to pair with
Bluetooth device
Successful Bluetooth pairing
2 beeps
Razz or error tone
Successful menu change
Unsuccessful menu change
Low Battery Indicator
Battery LED
If your battery is low, the battery LED double flashes orange and the scanner double chirps. The
programmable button can also be set to display the battery charge level. See Battery Charge
Status on page 4-2.
Reset Scanner
Scanning this bar code reboots the scanner and causes it to relink with the host.
Reset Scanner
Scanner Report
Scan the bar code below to generate a report for the connected scanners. The report indicates the port, work group, scanner
name, and address. To assign a name to your scanner, refer to Menu Command Syntax, page 9-1.
Scanner Report
3-6
Scanner Address
Scan the bar code below to determine the address of the scanner you are using.
Scanner Address
Linked Modes
Locked Link Mode and Open Link Mode are the link modes that accommodate different applications. Scan the appropriate bar
codes included in the Open Link and Locked Link Mode explanations that follow to switch from one mode to another. Default =
Open Link Mode.
Locked Link Mode - Single Scanner
When you scan the bar code below, only the linked scanner can connect to the host and other scanners are blocked from
being linked to that host.
Locked Link Mode
(Single Scanner)
To use a different scanner, you need to unlink the original scanner by scanning the Unlink Scanner bar code. (See
Unlinking the Scanner, below.)
Open Link Mode - Single Scanner
When in Open Link - Single Scanner Mode, each time a scanner is paired with a host, the scanner becomes linked to the
host and the old scanner is unlinked.
* Open Link Mode
(Single Scanner)
Unlinking the Scanner
If a host has a scanner linked to it, that scanner must be unlinked before a new scanner can be linked. Once the previous
scanner is unlinked, it will no longer communicate with the host. To unlink the scanner from a host, scan the Unlink Scanner bar code below.
Unlink Scanner
3-7
Override Locked Scanner
If you need to replace a broken or lost scanner that is linked to a host, scan the Override Locked Scanner bar code below
with a new scanner and pair that scanner with the host. The locked link will be overridden; the broken or lost scanner’s link
with the host will be removed, and the new scanner will be linked.
Override Locked Scanner
(Single Scanner)
Out-of-Range Alarm
Note: This feature is only supported by a Honeywell Access Point (AP). See Access Point Operations, beginning on page 3-13
for further information.
If your scanner is out range of the AP, an alarm sounds from the scanner. The alarm stops when the scanner is moved closer to
the AP, when the AP links to another scanner, or when the alarm duration expires. To set the alarm duration, scan the bar code
below and then set the time-out duration (from 0-3000 seconds) by scanning digits on the Programming Chart inside the back
cover, then scanning Save. Default = 0 sec (no alarm).
Scanner Alarm Duration
Note: If you are out of range when you scan a bar code, you will receive an error tone even if you do not have the alarm set
because the data could not be communicated to the AP.
Alarm Sound Type
Change the alarm type by scanning the following bar code and then scanning a digit (0-7) bar code and the Save bar code
on the Programming Chart inside the back cover of this manual. Default = 0.
The sounds are as follows:
Setting
Sound
0
3 long beeps, medium pitch
1
3 long beeps, high pitch
2
4 short beeps, medium pitch
3
4 short beeps, high pitch
4
single chirps, medium pitch
5
2 chirps, then 1 chirp, medium pitch
6
single chirps, high pitch
7
2 chirps, then 1 chirp, high pitch
Scanner Alarm Type
3-8
Scanner Idle Alarm
When the scanner is idle for over 1 hour, you can set it to beep every minute until the trigger is pressed. Default = Scanner Idle
Alarm Off.
Scanner Idle Alarm On
* Scanner Idle Alarm Off
Scanner Power Time-Out Timer
When there is no activity within a specified time period, the scanner enters low power mode. Scan the appropriate scanner
power time-out bar code to change the time-out duration (in seconds).
Note: Scanning zero (0) is the equivalent of setting no time-out.
If there are no scan button presses during the timer interval, the scanner goes into power down mode. Whenever the scan button is pressed, the timer is reset. The scanner will not go into power down mode when the battery is charging. Default = 3600
seconds.
0 seconds
200 seconds
400 seconds
900 seconds
* 3600 seconds
7200 seconds
3-9
Note: When the scanner is in power down mode, press the scan button to power the unit back up. There will be a set of power
up beeps and a delay of up to a few seconds for the radio to join. The scanner will then be ready to use.
Flexible Power Management
If you are experiencing network performance issues, and suspect the scanner is interfering with other devices, you can turn
down the power output of the scanner. This reduces the range between the scanner and a host as shown in the following illustration:
802.11
LAN
Scanner
Red
r
uced Powe
Full Power
Scan one of the bar codes below to set the scanner’s power output to Full Power (100%), Medium Power (35%), Medium Low
Power (5%), or Low Power (1%). Default = Full Power.
* Full Power
Medium Power
Medium Low Power
Low Power
Multiple Scanner Operation
Note: Multiple Scanner Operation Mode allows you to link up to 7 scanners to one Access Point. You cannot join an 8th scanner
until you unlink one of the 7 scanners or take a scanner out of range.
To put the scanner in multiple scanner mode, scan the bar code below. Once you scan this bar code, the scanner is unlinked
from the current host and must be paired with a host to relink.
Multiple Scanner Operation
Scanner Name
You may assign a name to each scanner you are using for identification purposes. For example, you may want to have a unique
identifier for a scanner that is receiving specific commands sent from the host.
3 - 10
The default name is in the format “ScannerName_Model_SN_XXXXXXXXXX” If you have more than one scanner linked to a
host and they all have the same name, the first scanner linked to the host receives commands. When renaming a series of
scanners with identical names, unlink all except one of the scanners from the host.
Perform the rename operation using either the bar codes on page 3-11, or by sending the serial command :ScannerName:BT_NAMNewName. where ScannerName is the current name of the scanner, and NewName is the new name for the
scanner. If you wish to change the names of additional scanners, link them one at a time and repeat the :ScannerName:BT_NAMNewName. command for each scanner.
To rename scanners with sequential, numeric names, scan the bar codes below. Scan the Reset code after each name change
and wait for the scanner to relink to the host before scanning a bar code to rename the next scanner.
0001
0002
0003
0004
0005
0006
0007
Reset
You may also scan the Scanner Name bar code below and scan a number for the scanner name. For example, if you wanted to
name the linked scanner “312,” you would scan the bar code below, scan the 3, 1, and 2 bar codes on the Programming Chart
inside the back cover of this manual, then scan Save. Scan the Reset bar code and wait for the scanner to relink to the host.
Scanner Name
3 - 11
Application Work Groups
Note: Application Work Groups can only be used with an Access Point.
Your wireless system can have up to 7 scanners linked to one host. You can also have up to 7 work groups. If you want to have
all of the scanners’ settings programmed alike, you don’t need to use more than one work group. If you want each scanner to
have unique settings (e.g., beeper volume, prefix/suffix, data formatter), then you may program each scanner to its own unique
work group and may program each scanner independently. For example, you might want to have multiple work groups in a
retail/warehouse application where you need to have different data appended to bar codes used in the warehouse area versus
the retail area. You could assign all the scanners in the retail area to one work group and those in the warehouse to another.
Consequently, any desired changes to either the retail or warehouse area would apply to all scanners in that particular work
group. Honeywell’s online configuration tool, EZConfig-Scanning (page 8-2), makes it easy for you to program your system for
use with multiple scanners and multiple work groups.
The scanner keeps a copy of the menu settings it is using. Whenever the scanner is connected or reconnected to a host, the
scanner is updated with the latest settings from the host for its work group. The scanner also receives menu setting changes
processed by the host. If a scanner is removed from a host and linked to another host, it will be updated with the new host settings for whatever work group to which that the scanner was previously assigned. For example, if the scanner was in work
group 1 linked to the first host, it will be placed in work group 1 in the second host with the associated settings.
Application Work Group Selection
This programming selection allows you to assign a scanner to a work group by scanning the bar code below. You may then
program the settings (e.g., beeper volume, prefix/suffix, data formatter) that your application requires. Default = Group 0.
* Group 0
Group 1
Group 2
Group 3
Group 4
Group 5
Group 6
3 - 12
Resetting the Factory Defaults: All Application Work Groups
The following bar code defaults all of the work groups to the factory default settings.
PAPDFT&
Factory Default Settings:
All Work Groups
To see what the factory default settings are, refer to the table of Menu Commands, beginning on page 9-4. The standard product default settings for each of the commands are indicated by an asterisk (*).
Note: Scanning this bar code also causes both the scanner and the host to perform a reset and become unlinked. You must
relink (pair) the scanner to the host. Refer to Bluetooth Settings, page 3-1 for additional information.
If your scanner is in multiple scanner mode, you will hear up to 30 seconds of beeping while all scanners are relinked to
the host and the settings are changed.
Resetting the Custom Defaults: All Application Work Groups
If you want the custom default settings restored to all of the work groups, scan the Custom Product Default Settings bar code
below. (If there are no custom defaults, it will reset the work groups to the factory defaults.) See Setting Custom Defaults on
page 1-6 for further information about custom defaults.
Custom Default Settings:
All Work Groups
Note: Scanning this bar code also causes both the scanner and the host to perform a reset and become unlinked. You must
relink (pair) the scanner to the host. See Bluetooth Settings, page 3-1 for additional information.
If your scanner is in multiple scanner mode, you will hear up to 30 seconds of beeping while all scanners are relinked to
the host and the settings are changed.
Access Point Operations
The Voyager 1602g can pair with a Honeywell Access Point (AP01-010BT or AP01-100BT), which provides 2-way communication between the scanner and host.
Linking the Scanner to an Access Point
Turn on the host computer (laptop/desktop). Plug the interface cable into the Access Point
first and then into the appropriate port on the computer. The Page button lights up when the
connection to the host is made.
Page
Button
3 - 13
Scan the linking bar code on the top of the Access Point to establish a connection between the Access Point and the scanner. The scanner emits a short beep and flashes the green LED to confirm a connection with the Access Point. The
Access Point’s Page button remains blue.
If the Access Point sounds 5 error tones followed by 3 beeps, it indicates that you are attempting to link to the incorrect
model Access Point. The Voyager 1602g scanner can only link to an Access Point model AP01-010BT or AP01-100BT.
Disconnect from Host and Connect to an Access Point
If your scanner has been connected directly to an iPad, smart phone, or laptop, you must disconnect it in order to communicate with an Access Point. Scan the Bluetooth HID Keyboard Disconnect bar code to unlink the scanner from the currently linked host. Scan the linking bar code on the Access Point to link the scanner to the Access Point.
Bluetooth HID Keyboard Disconnect
Replacing a Linked Scanner
If you need to replace a broken or lost scanner that is linked to an Access Point, scan the Override Locked Scanner bar
code below with a new scanner and scan the Access Point linking bar code. The locked link will be overridden; the broken
or lost scanner’s link with the Access Point will be removed, and the new scanner will be linked.
Override Locked Scanner
(Single Scanner)
3 - 14
Access Point LED Sequences and Meaning
The Access Point has a blue LED on the top of the unit that indicates its power up and communication condition.
Blue LED - Host Communication
Blue LED
Communication Condition
Off
USB suspend
On continuously
Power on, system idle
Short blinks in multiple pulses. Occurs while transferring data to/
from the host.
Receiving data
Access Point Address
Scan the bar code below to determine the address of the Access Point you are using.
Base Address
Paging
Paging Mode
By default, the paging button on the Access Point pages the scanners associated with that Access Point. If you want the
paging button on your Access Point to be disabled, scan the Paging Mode Off bar code, below. When Paging Mode is off,
the Access Point will no longer page scanners when the button is pressed. The blue LED on the Access Point will remain
lit to indicate that Paging Mode is off. (This light will go out when the button is pressed, then back on when it’s released.)
Default = Paging Mode On.
* Paging Mode On
Paging Mode Off
Paging Pitch
When you press the Page button on the Access Point, the scanners associated with that Access Point will begin beeping.
You can set the pitch of the paging beep for each scanner by scanning one of the following bar codes. Default = Low.
* Low (1000 Hz)
Medium (3250 Hz)
3 - 15
High (4200 Hz)
Batch Mode
Batch mode is used to store bar code data when a scanner is out of range of its host, or when performing inventory. The scanner may store a number of symbols (approximately 500 U.P.C. symbols; others may vary) when it is out of range and then send
them to the host when back in range or when the records are manually transmitted.
Note: Batch mode has limitations when using multiple scanners with one Access Point. When a wireless system is being used
in "multiple link mode," where up to 7 scanners are connected to one Access Point, some accumulated or batched scans
could be lost if scanners are constantly moved in and out of range.
Automatic Batch Mode stores bar code data when the scanner is out of range of the host or Access Point. The data is automatically transmitted to the host or Access Point once the scanner is back in range. When the scanner’s buffer space is full, any
bar codes scanned generate an error tone. In order to scan bar codes again, the scanner must be moved back into range of the
host or Access Point so data can be transmitted.
Inventory Batch Mode stores bar code data, whether or not you are in range of the host or Access Point. To transmit the
stored data to the host or Access Point, scan Transmit Inventory Records (page 3-20). When the scanner’s buffer space is full,
any bar codes scanned generate an error tone. In order to scan bar codes again, the data must be transmitted to the host or
Access Point. Once the data is transmitted, it is cleared in the scanner.
Persistent Batch Mode is the same as Inventory Batch Mode, except that once the data is transmitted to the host or Access
Point, it is retained in the scanner. If you want to transmit more than once, you can do so using this mode. In order to clear the
scanner’s buffer, you must scan Clear All Codes (see page 3-20).
Default = Batch Mode Off.
* Batch Mode Off
Automatic Batch Mode
Inventory Batch Mode
Persistent Batch Mode
3 - 16
Batch Mode Beep
When scanning in Inventory Batch Mode (page 3-16), the scanner beeps every time a bar code is scanned. When Batch
Mode Beep is On, you will also hear a click when each bar code is sent to the host. If you do not want to hear these clicks,
scan Batch Mode Beep Off. Default = Batch Mode Beep On.
Batch Mode Beep Off
* Batch Mode Beep On
Batch Mode Storage
When a scanner is storing data during a Batch Mode process, you can select whether the data is stored in Flash memory
or in RAM.
Flash Storage: The scanner writes any untransmitted data to flash memory prior to powering down. The data will still be
there when the scanner powers back up. However, the scanner will power down, even with untransmitted data, if it reaches
a power down timeout or if the battery power is very low.
RAM Storage: The scanner will not power down while it contains data that has not been transmitted to the host or Access
Point, even if it reaches a power down timeout. However, if the scanner runs out of battery power, it will power down and
the data will be lost.
Default = Flash Storage.
* Flash Storage
RAM Storage
Batch Mode Quantity
When in Batch Mode, you may wish to transmit the number of multiple bar codes scanned, rather than a single bar code
multiple times. For example, if you scan three bar codes called XYZ with Batch Mode Quantity Off, when you transmit
your data it will appear as XYZ three times. Using Batch Mode Quantity On and the Quantity Codes (page 3-19), you
could output your data as “XYZ, 00003” instead.
Note: If you wish to format your output, for example, place a CR or tab between the bar code data and the quantity, refer
to Data Formatting beginning on page 6-1.
Default = Batch Mode Quantity Off.
* Batch Mode Quantity Off
3 - 17
Batch Mode Quantity On
Entering Quantities
Quantity Codes (page 3-19) allow you to enter a quantity for the last item scanned, up to 9999 (default = 1). Quantity digits
are shifted from right to left, so if a 5th digit is scanned, the 1st digit scanned is discarded and the 2nd, 3rd and 4th digits
are moved to the left to accommodate the new digit.
For example, if the Quantity 5 bar code is scanned after the quantity has been set to 1234, then the 1 is dropped, the quantity will be 2345.
Example: Add a quantity of 5 for the last item scanned.
1. Scan the item's bar code.
2. Scan the quantity 5 bar code.
Example: Add a quantity of 1,500 for the last item scanned.
1. Scan the item's bar code.
2. Scan the quantity 1 bar code.
3. Scan the quantity 5 bar code.
4. Scan the quantity 0 bar code.
5. Scan the quantity 0 bar code.
Example: Change a quantity of 103 to 10.
To correct an incorrect quantity, scan the quantity 0 bar code to replace the incorrect digits, then scan the correct quantity
bar codes.
1. Scan the quantity 0 bar code to change the quantity to 1030.
2. Scan the quantity 0 bar code to change the quantity to 0300.
3. Scan the quantity 1 bar code to change the quantity to 3001.
4. Scan the quantity 0 bar code to change the quantity to 0010.
Default = 1.
Quantity Codes
0
1
2
3
3 - 18
4
5
6
7
8
9
Batch Mode Output Order
When batch data is transmitted, select whether you want that data sent as FIFO (first-in first-out), or LIFO (last-in first-out).
Default = Batch Mode FIFO.
* Batch Mode FIFO
Batch Mode LIFO
Total Records
If you wish to output the total number of bar codes scanned when in Batch Mode, scan Total Records.
Total Records
3 - 19
Delete Last Code
If you want to delete the last bar code scanned when in Batch Mode, scan Delete Last Code.
Delete Last Code
Clear All Codes
If you want to clear the scanner’s buffer of all data accumulated in Batch Mode, scan Clear All Codes.
Clear All Codes
Transmit Records to Host
If you are operating in Inventory Batch Mode (see Inventory Batch Mode on page 3-16), you must scan the following bar
code to transmit all the stored data to the host system.
Transmit Inventory Records
Batch Mode Transmit Delay
Sometimes when accumulated scans are sent to the host system, the transmission of those scans is too fast for the application to process. To program a transmit delay between accumulated scans, scan one of the following delays. Default =
Off.
Note: In most cases, a short (250 ms (milliseconds)) delay is ideal, however, longer delays may be programmed. Contact
Technical Support (page -ix) for additional information.
* Batch Mode Transmit Delay Off
(No Delay)
Batch Mode Transmit Delay Short
(250 ms)
Batch Mode Transmit Delay Medium
(500 ms)
Batch Mode Transmit Delay Long
(1000 ms)
3 - 20
Host Acknowledgment
Some applications require that the host validate incoming bar code data (database look-up) and provide acknowledgment to the
scanner whether or not to proceed. In Host ACK Mode, the scanner waits for this acknowledgment after each scan. Visual and
audible acknowledgments provide valuable feedback to the scan operator. The Host ACK functionality is controlled via a number of pre-defined escape commands that are sent to the scanner to make it behave in different ways.
Note: System performance degrades when using Host ACK at rates lower than 9600 baud.
The following criteria must be met for the Host ACK to work correctly:
•
•
•
•
•
•
The scanner must be paired with a Honeywell Access Point (AP01-010BT or AP01-100BT).
The wireless system must be configured for Host Port RS232 (terminal ID = 000) or USB COM Emulation (terminal ID = 130).
RTS/CTS is defaulted off. You must enable it if the host system requires it.
Host ACK must be set to On (page 3-22).
A comma must be used as a terminator.
The host terminal software must be capable of interpreting the bar code data, make decisions based on the data content, and
send out appropriate escape commands to the scanner.
Escape commands are addressed to the scanner via Application Work Groups. Once a command is sent, all scanners in a
group respond to that command. Because of this, it is recommended that each scanner is assigned to its own group in
Host ACK mode.
The commands to which the scanner responds are listed on page 3-22. The [ESC] is a 1B in hex. A typical command string is
y [ESC] x, where “y” is the application work group number, “[ESC] x” is the escape command, and the comma is the terminator,
which is required. (When “y” is not specified, the command is sent to the default Application Work Group 0.)
Example: Commands may be strung together to create custom response sequences. An example of a command string is listed
below.
0[ESC]4,[ESC]5,[ESC]6,
The above example will make a scanner that is in application work group zero beep low, then medium, then high.
Example: A good read beep is required for any item on file, but a razz or error tone is required if the item is not on file. In this
case,
[ESC]7, is sent to the host for an on-file product
[ESC]8,[ESC]8, is sent to the host for a not-on-file product
When a bar code is scanned, the scanner enters a timeout period until either the host ACK sequence is received, or the timeout
expires (in 10 seconds, by default).
Once Host ACK is enabled, the system works as follows when a bar code is scanned:
• The scanner reads the code and sends data to the host. No audible or visual indication is emitted until the scanner receives
an escape command. The scanner read illumination goes out when there’s a successful read.
• Scanner operation is suspended until 1) a valid escape string is received from the host or 2) the scanner times out.
• Once condition 1 or 2 above has been met, the scanner is ready to scan again, and the process repeats.
A time-out occurs if the scanner does not receive a valid escape command within 10 seconds. A time-out is indicated by an
error tone. If a time-out occurs, the operator should check the host system to understand why a response to the scanner was
not received.
3 - 21
Host ACK On/Off
Host ACK On
* Host ACK Off
Host ACK Timeout
You can set a timeout for the length of time the scanner waits for a valid escape command when using Host Acknowledgment Mode. Set the length (in seconds) for a timeout by scanning the following bar code, then setting the timeout (from 190 seconds) by scanning digits from the Programming Chart inside the back cover of this manual, then scanning Save.
Default = 10.
Host ACK Timeout
Host ACK Responses
Command
Action
[ESC] a,
Double beeps to indicate a successful menu change was made.
[ESC] b,
Razz or error tone to indicate a menu change was unsuccessful.
[ESC] 1,
The green LED illuminates for 135 milliseconds followed by a pause.
[ESC] 2,
The green LED illuminates for 2 seconds followed by a pause.
[ESC] 3,
The green LED illuminates for 5 seconds followed by a pause.
[ESC] 4,
Emits a beep at a low pitch.
[ESC] 5,
Emits a beep at a medium pitch.
[ESC] 6,
Emits a beep at a high pitch.
[ESC] 7,
Beeps to indicate a successful decode and communication to host.
[ESC] 8,[ESC] 8,
Razz or error tone to indicate a decode/communication to host was unsuccessful.
3 - 22
4
Input/Output Settings
Programmable Button
The second, smaller button on the scanner can be programmed so that pressing the button displays a virtual keyboard on the
host, displays the battery charge status, puts the scanner into flashlight mode, or pairs and unpairs the Bluetooth connection
between the scanner and the host. You may program one of these selections to occur after a short button press, and another
selection to occur after a long button press. The scanner emits a short beep to let you know when the button has been held
down long enough.
Programmable button
Virtual Keyboard
Once your scanner has been connected directly to an Apple® iPad, smart phone, or laptop, you can toggle the virtual keyboard on the host with either a short or a long press of the programmable button.
Note: This feature is only supported with Apple devices.
Virtual Keyboard On Short Press
Virtual Keyboard On Long Press
4-1
Battery Charge Status
If you want the battery indicator LED to flash in a pattern that indicates the battery charge level, scan one of the following
bar codes.
Battery Charge Status On Short Press
Battery Charge Status On Long Press
The battery LED flashes in the following patterns after a short or long press of the programmable button:
Battery LED
LED Indicator
Battery Charge Status
Orange flash
Battery is charging
Orange, blink once
Battery is 25–49%
Orange, blink twice
Battery is 50–74%
Orange, blink three times
Battery is 75–99%
Green, on
Battery is fully charged
Red, on
Low battery 0-24%
Red blink
Charging error
Flashlight Mode
If you want the scanner to act as a flashlight, scan one of the bar codes below. Pressing the programmable button (short or
long press) turns the flashlight on. Pressing the scan button turns it back off.
Flashlight Mode On Short Press
Flashlight Mode On Long Press
4-2
Bluetooth Pair/Unpair
The programmable button can be used to toggle between pairing and unpairing from the host. Scan one of the following
bar codes to set the Bluetooth Pair/Unpair with a short or long press of the programmable button:
Bluetooth Pair/Unpair On Short Press
Bluetooth Pair/Unpair On Long Press
The Bluetooth LED flashes in the following pattern after a short or long press of the programmable button
LED Indicator
Beeper Indicator
Bluetooth Status
Blue, off
None
Bluetooth connection has not been established
Blue flash
None
Scanner is attempting to pair with Bluetooth device
Blue, on
1 beep
Successful Bluetooth pairing
Bluetooth LED
Disable Programmable Button
To disable the programmable button, scan one or both of the bar codes below. Default = Disable Short and Long Press.
* Disable Short Press
* Disable Long Press
4-3
Power Up Beeper
The scanner can be programmed to beep when it’s powered up. Scan the Off bar code(s) if you don’t want a power up beep.
Default = Power Up Beeper On.
Power Up Beeper Off
* Power Up Beeper On
Beep on BEL Character
You may wish to force the scanner to beep upon a command sent from the host. If you scan the Beep on BEL On bar code
below, the scanner will beep every time a BEL character is received from the host. Default = Beep on BEL Off.
*Beep on BEL Off
Beep on BEL On
Trigger Click
To hear an audible click every time the scanner button is pressed, scan the Trigger Click On bar code below. Scan the Trigger
Click Off code if you don’t wish to hear the click. (This feature has no effect on serial or automatic triggering.) Default = Trigger
Click Off.
*Trigger Click Off
Trigger Click On
4-4
Good Read and Error Indicators
Beeper – Good Read
The beeper may be programmed On or Off in response to a good read. Turning this option off only turns off the beeper
response to a good read indication. All error and menu beeps are still audible. Default = Beeper - Good Read On.
Beeper - Good Read Off
* Beeper - Good Read On
Beeper Volume – Good Read
The beeper volume codes modify the volume of the beep the scanner emits on a good read. Default = High.
Low
Medium
* High
Off
Beeper Pitch – Good Read
The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read. Default = Medium.
Low (1600 Hz)
* Medium (2700 Hz)
4-5
High (4200 Hz)
Beeper Pitch – Error
The beeper pitch codes modify the pitch (frequency) of the sound the scanner emits when there is a bad read or error.
Default = Razz.
* Razz (250 Hz)
Medium (3250 Hz)
High (4200 Hz)
Beeper Duration – Good Read
The beeper duration codes modify the length of the beep the scanner emits on a good read. Default = Normal.
* Normal Beep
Short Beep
LED – Good Read
The LED indicator can be programmed On or Off in response to a good read. Default = On.
* LED - Good Read On
LED - Good Read Off
4-6
Number of Beeps – Good Read
The number of beeps of a good read can be programmed from 1 - 9. The same number of beeps will be applied to the
beeper and LED in response to a good read. For example, if you program this option to have five beeps, there will be five
beeps and five LED flashes in response to a good read. The beeps and LED flashes are in sync with one another. To
change the number of beeps, scan the bar code below and then scan a digit (1-9) bar code and the Save bar code on the
Programming Chart inside the back cover of this manual. Default = 1.
Number of Good Read Beeps/LED Flashes
Number of Beeps – Error
The number of beeps and LED flashes emitted by the scanner for a bad read or error can be programmed from 1 - 9. For
example, if you program this option to have five error beeps, there will be five error beeps and five LED flashes in response
to an error. To change the number of error beeps, scan the bar code below and then scan a digit (1-9) bar code and the
Save bar code on the Programming Chart inside the back cover of this manual. Default = 1.
Number of Error Beeps/LED Flashes
Good Read Delay
This sets the minimum amount of time before the scanner can read another bar code. Default = 0 ms (No Delay).
* No Delay
Short Delay (500 ms)
Medium Delay (1,000 ms)
Long Delay (1,500 ms)
User-Specified Good Read Delay
If you want to set your own length for the good read delay, scan the bar code below, then set the delay (from 0 - 30,000 milliseconds) by scanning digits from the inside back cover, then scanning Save.
User-Specified Good Read Delay
4-7
Manual Trigger Modes
When in manual trigger mode, the scanner scans until a bar code is read or until the scan button is released. Two modes are
available, Normal and Enhanced. Normal mode offers good scan speed and the longest working ranges (depth of field).
Enhanced mode will give you the highest possible scan speed but slightly less range than Normal mode. Enhanced mode is
best used when you require a very fast scan speed and don’t require a long working range. Default = Manual Trigger-Normal.
* Manual Trigger - Normal
Manual Trigger - Enhanced
Serial Trigger Mode
You can activate the scanner either by pressing the scan button, or using a serial trigger command (see Trigger Commands on
page 9-3). You must be in a serial interface mode in order to use serial triggering. Refer to RS232 Serial Port (page 2-12) or
USB Serial (page 2-15) for further information. When in serial mode, the scanner scans until a bar code has been read or until
the deactivate command is sent. The scanner can also be set to turn itself off after a specified time has elapsed (see Read
Time-Out, which follows).
Read Time-Out
Use this selection to set a time-out (in milliseconds) of the scan button when using serial commands to trigger the scanner.
Once the scanner has timed out, you can activate the scanner either by pressing the scan button or using a serial trigger
command. After scanning the Read Time-Out bar code, set the time-out duration (from 0-300,000 milliseconds) by scanning digits on the Programming Chart inside the back cover, then scanning Save. Default = 30,000 ms.
Read Time-Out
Poor Quality Codes
Poor Quality 1D Codes
This setting improves the scanner’s ability to read damaged or badly printed linear bar codes. When Poor Quality 1D
Reading On is scanned, poor quality linear bar code reading is improved, but the scanner’s snappiness is decreased, making it less aggressive when reading good quality bar codes. This setting does not affect 2D bar code reading. Default =
Poor Quality 1D Reading Off.
Poor Quality 1D Reading On
* Poor Quality 1D Reading Off
4-8
Poor Quality PDF Codes
This setting improves the scanner’s ability to read damaged or badly printed PDF codes by combining information from multiple images. When Poor Quality PDF On is scanned, poor quality PDF code reading is improved, but the scanner’s snappiness is decreased, making it less aggressive when reading good quality bar codes. This setting does not affect 1D bar
code reading. Default = Poor Quality PDF Reading Off.
Poor Quality PDF Reading On
* Poor Quality PDF Reading Off
CodeGate®
When CodeGate is On, the scan button is used to allow decoded data to be transmitted to the host system. The scanner
remains on, scanning and decoding bar codes, but the bar code data is not transmitted until the scan button is pressed. When
CodeGate is Off, bar code data is transmitted when it is decoded. Default = CodeGate Off Out-of-Stand.
* CodeGate Off
Out-of-Stand
CodeGate On
Out-of-Stand
Mobile Phone Read Mode
When this mode is selected, your scanner is optimized to read bar codes from mobile phone or other LED displays. However,
the speed of scanning printed bar codes may be slightly lower when this mode is enabled.
Hand Held Scanning - Mobile
Phone
Note: To turn off Mobil Phone Read Mode, scan a Manual or Serial Trigger Mode bar code (see page 4-8).
4-9
Character Activation Mode
You may use a character sent from the host to trigger the scanner to begin scanning. When the activation character is received,
the scanner continues scanning until either the Character Activation Timeout (page 4-11), the deactivation character is received
(see Deactivation Character on page 4-11), or a bar code is transmitted. Scan the following On bar code to use character activation, then use Activation Character (following) to select the character you will send from the host to start scanning. Default =
Off.
* Off
On
Activation Character
This sets the character used to trigger scanning when using Character Activation Mode. On the ASCII Conversion Chart
(Code Page 1252), page A-3, find the hex value that represents the character you want to use to trigger scanning. Scan
the following bar code, then use the Programming Chart to read the alphanumeric combination that represents that ASCII
character. Scan Save to finish. Default = 12 [DC2].
Activation Character
End Character Activation After Good Read
After a bar code is successfully detected and read from the scanner, the illumination can be programmed either to remain
on and scanning, or to turn off. When End Character Activation After Good Read is enabled, the illumination turns off
and stops scanning after a good read. If you scan Do Not End Character Activation After Good Read, the illumination
remains on after a good read. Default = Do Not End Character Activation After Good Read.
* Do Not End Character
Activation After Good Read
End Character Activation After
Good Read
4 - 10
Character Activation Timeout
You can set a timeout for the length of time the illumination remains on and attempting to decode bar codes when using
Character Activation Mode. Set the length (in milliseconds) for a timeout by scanning the following bar code, then setting
the timeout (from 1-300,000 milliseconds) by scanning digits from the Programming Chart inside the back cover of this
manual, then scanning Save. Default = 30,000 ms.
Character Activation Timeout
Character Deactivation Mode
If you have sent a character from the host to trigger the scanner to begin scanning, you can also send a deactivation character
to stop scanning. Scan the following On bar code to use character deactivation, then use Deactivation Character (following) to
select the character you will send from the host to terminate scanning. Default = Off.
* Off
On
Deactivation Character
This sets the character used to terminate scanning when using Character Deactivation Mode. On the ASCII Conversion
Chart (Code Page 1252), page A-3, find the hex value that represents the character you want to use to terminate scanning.
Scan the following bar code, then use the Programming Chart inside the back cover of this manual to read the alphanumeric combination that represents that ASCII character. Scan Save to finish. Default = 14 [DC4].
Deactivation Character
Illumination Lights
If you want the illumination lights on while reading a bar code, scan the Lights On bar code, below. However, if you want to turn
just the lights off, scan the Lights Off bar code. Default = Lights On.
Note: This setting does not affect the aimer light. The aiming light can be set using Aimer Mode (page 4-12).
* Lights On
Lights Off
4 - 11
Aimer Delay
The aimer delay allows a delay time for the operator to aim the scanner before the bar code is read. Use these codes to set the
time between when the button is pressed and when the bar code is read. During the delay time, the aiming light will appear, but
the LEDs won’t turn on until the delay time is over. Default = Off.
200 milliseconds
400 milliseconds
* Off (no delay)
User-Specified Aimer Delay
If you want to set your own length for the duration of the delay, scan the bar code below, then set the time-out by scanning
digits (0 - 4,000 ms) from the Programming Chart inside the back cover of this manual, then scan Save.
Delay Duration
Aimer Mode
This feature allows you to turn the aimer on and off. When the Interlaced bar code is scanned, the aimer is interlaced with the
illumination LEDs. Default = Interlaced.
Off
* Interlaced
Centering
Use Centering to narrow the scanner’s field of view to make sure that when the scanner is hand-held, it reads only those bar
codes intended by the user. For instance, if multiple codes are placed closely together, centering will insure that only the
desired codes are read. (Centering can be used in conjunction with Aimer Delay, page 4-12, for the most error-free operation
in applications where multiple codes are spaced closely together. Using the Aimer Delay and Centering features, the scanner
can emulate the operation of older systems, such as linear laser bar code scanners.)
If a bar code is not touched by a predefined window, it will not be decoded or output by the scanner. If centering is turned on by
scanning Centering On, the scanner only reads codes that pass through the centering window you specify using the Top of
Centering Window, Bottom of Centering Window, Left, and Right of Centering Window bar codes.
4 - 12
In the example below, the white box is the centering window. The centering window has been set to 20% left, 30% right, 8% top,
and 25% bottom. Since Bar Code 1 passes through the centering window, it will be read. Bar Code 2 does not pass through
the centering window, so it will not be read.
0%
Bar Code 1
10
Bar Code 2
20
30
40
50
60
70
80
90
100
0
10
20
30
40
50
60
70
80
90
100%
Note: A bar code needs only to be touched by the centering window in order to be read. It does not need to pass completely
through the centering window.
Scan Centering On, then scan one of the following bar codes to change the top, bottom, left, or right of the centering window.
Then scan the percent you want to shift the centering window using digits on the inside back cover of this manual. Scan Save.
Default Centering = 40% for Top and Left, 60% for Bottom and Right.
Centering On
* Centering Off
Top of Centering Window
Bottom of Centering Window
Left of Centering Window
4 - 13
Right of Centering Window
Preferred Symbology
The scanner can be programmed to specify one symbology as a higher priority over other symbologies in situations where both
bar code symbologies appear on the same label, but the lower priority symbology cannot be disabled.
For example, you may be using the scanner in a retail setting to read U.P.C. symbols, but have occasional need to read a code
on a drivers license. Since some licenses have a Code 39 symbol as well as the PDF417 symbol, you can use Preferred Symbology to specify that the PDF417 symbol be read instead of the Code 39.
Preferred Symbology classifies each symbology as high priority, low priority, or as an unspecified type. When a low priority
symbology is presented, the scanner ignores it for a set period of time (see Preferred Symbology Time-out on page 4-15) while
it searches for the high priority symbology. If a high priority symbology is located during this period, then that data is read immediately.
If the time-out period expires before a high priority symbology is read, the scanner will read any bar code in its view (low priority
or unspecified). If there is no bar code in the scanner’s view after the time-out period expires, then no data is reported.
Note: A low priority symbol must be centered on the aiming pattern to be read.
Scan a bar code below to enable or disable Preferred Symbology.
Default = Preferred Symbology Off.
Preferred Symbology On
* Preferred Symbology Off
High Priority Symbology
To specify the high priority symbology, scan the High Priority Symbology bar code below. On the Symbology Charts on
page A-1, find the symbology you want to set as high priority. Locate the Hex value for that symbology and scan the 2 digit
hex value from the Programming Chart (inside back cover). Scan Save to save your selection. Default = None
High Priority Symbology
Low Priority Symbology
To specify the low priority symbology, scan the Low Priority Symbology bar code below. On the Symbology Charts on page
A-1, find the symbology you want to set as low priority. Locate the Hex value for that symbology and scan the 2 digit hex
value from the Programming Chart (inside back cover).
4 - 14
If you want to set additional low priority symbologies, scan FF, then scan the 2 digit hex value from the Programming Chart
for the next symbology. You can program up to 5 low priority symbologies. Scan Save to save your selection. Default =
None.
Low Priority Symbology
Preferred Symbology Time-out
Once you have enabled Preferred Symbology and entered the high and low priority symbologies, you must set the time-out
period. This is the period of time the scanner will search for a high priority bar code after a low priority bar code has been
encountered. Scan the bar code below, then set the delay (from 1-3,000 milliseconds) by scanning digits from the inside
back cover, then scanning Save. Default = 500 ms.
Preferred Symbology Time-out
Preferred Symbology Default
Scan the bar code below to set all Preferred Symbology entries to their default values.
Preferred Symbology Default
Output Sequence Overview
Output Sequence Editor
This programming selection allows you to program the scanner to output data (when scanning more than one symbol) in
whatever order your application requires, regardless of the order in which the bar codes are scanned. Reading the Default
Sequence symbol programs the scanner to the Universal values, shown below. These are the defaults. Be certain you
want to delete or clear all formats before you read the Default Sequence symbol.
Note: To make Output Sequence Editor selections, you’ll need to know the code I.D., code length, and character match(es)
your application requires. Use the Alphanumeric symbols (inside back cover) to read these options. You must hold
the scan button while reading each bar code in the sequence.
To Add an Output Sequence
1. Scan the Enter Sequence symbol (see Require Output Sequence, page 4-17).
2. Code I.D.
On the Symbology Charts on page A-1, find the symbology to which you want to apply the output sequence format.
Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart (inside back
cover).
3. Length
Specify what length (up to 9999 characters) of data output will be acceptable for this symbology. Scan the four digit
data length from the Programming Chart. (Note: 50 characters is entered as 0050. 9999 is a universal number,
indicating all lengths.) When calculating the length, you must count any programmed prefixes, suffixes, or formatted
characters as part of the length (unless using 9999).
4. Character Match Sequences
On the ASCII Conversion Chart (Code Page 1252), page A-3, find the Hex value that represents the character(s) you
want to match. Use the Programming Chart to read the alphanumeric combination that represents the ASCII
characters. (99 is the Universal number, indicating all characters.)
4 - 15
5. End Output Sequence Editor
Scan F F to enter an Output Sequence for an additional symbology, or Save to save your entries.
Other Programming Selections
• Discard
This exits without saving any Output Sequence changes.
Output Sequence Example
In this example, you are scanning Code 93, Code 128, and Code 39 bar codes, but you want the scanner to output Code 39
1st, Code 128 2nd, and Code 93 3rd, as shown below.
Note: Code 93 must be enabled to use this example.
A - Code 39
B - Code 128
C - Code 93
You would set up the sequence editor with the following command line:
SEQBLK62999941FF6A999942FF69999943FF
The breakdown of the command line is shown below:
SEQBLKsequence editor start command
62
code identifier for Code 39
9999
code length that must match for Code 39, 9999 = all lengths
41
start character match for Code 39, 41h = “A”
FF
termination string for first code
6A
code identifier for Code 128
9999
code length that must match for Code 128, 9999 = all lengths
42
start character match for Code 128, 42h = “B”
FF
termination string for second code
69
code identifier for Code 93
9999
code length that must match for Code 93, 9999 = all lengths
43
start character match for Code 93, 43h = “C”
FF
termination string for third code
To program the previous example using specific lengths, you would have to count any programmed prefixes, suffixes, or formatted characters as part of the length. If you use the example on page 4-16, but assume a <CR> suffix and specific code
lengths, you would use the following command line:
SEQBLK62001241FF6A001342FF69001243FF
The breakdown of the command line is shown below:
SEQBLKsequence editor start command
62
code identifier for Code 39
0012
A - Code 39 sample length (11) plus CR suffix (1) = 12
4 - 16
41
start character match for Code 39, 41h = “A”
FF
termination string for first code
6A
code identifier for Code 128
0013
B - Code 128 sample length (12) plus CR suffix (1) = 13
42
start character match for Code 128, 42h = “B”
FF
termination string for second code
69
code identifier for Code 93
0012
C - Code 93 sample length (11) plus CR suffix (1) = 12
43
start character match for Code 93, 43h = “C”
FF
termination string for third code
Output Sequence Editor
Enter Sequence
Default Sequence
Partial Sequence
If an output sequence operation is terminated before all your output sequence criteria are met, the bar code data acquired
to that point is a “partial sequence.”
Scan Discard Partial Sequence to discard partial sequences when the output sequence operation is terminated before
completion. Scan Transmit Partial Sequence to transmit partial sequences. (Any fields in the sequence where no data
match occurred will be skipped in the output.)
Transmit Partial Sequence
* Discard Partial Sequence
Require Output Sequence
When an output sequence is Required, all output data must conform to an edited sequence or the scanner will not transmit
the output data to the host device. When it’s On/Not Required, the scanner will attempt to get the output data to conform
to an edited sequence but, if it cannot, the scanner transmits all output data to the host device as is.
4 - 17
When the output sequence is Off, the bar code data is output to the host as the scanner decodes it. Default = Off.
Note: This selection is unavailable when the Multiple Symbols Selection is turned on.
Required
On/Not Required
*Off
Multiple Symbols
When this programming selection is turned On, it allows you to read multiple symbols with a single press of the scanner’s button. If you press and hold the button, aiming the scanner at a series of symbols, it reads unique symbols once, beeping (if
turned on) for each read. The scanner attempts to find and decode new symbols as long as the scan button is pressed. When
this programming selection is turned Off, the scanner will only read the symbol closest to the aiming beam. Default = Off.
On
* Off
No Read
With No Read turned On, the scanner notifies you if a code cannot be read. If using an EZConfig-Scanning Tool Scan Data
Window (see page 8-3), an “NR” appears when a code cannot be read. If No Read is turned Off, the “NR” will not appear.
Default = Off.
On
* Off
If you want a different notation than “NR,” for example, “Error,” or “Bad Code,” you can edit the output message (see Data
Formatting beginning on page 6-1). The hex code for the No Read symbol is 9C.
4 - 18
Video Reverse
Video Reverse is used to allow the scanner to read bar codes that are inverted. The Video Reverse Off bar code below is an
example of this type of bar code. Scan Video Reverse Only to read only inverted bar codes. Scan Video Reverse and Standard Bar Codes to read both types of codes.
Note: After scanning Video Reverse Only, menu bar codes cannot be read. You must scan Video Reverse Off or Video
Reverse and Standard Bar Codes in order to read menu bar codes.
Note: Images downloaded from the unit are not reversed. This is a setting for decoding only.
Video Reverse Only
Video Reverse and Standard Bar
Codes
* Video Reverse Off
Working Orientation
Some bar codes are direction-sensitive. For example, KIX codes and OCR can misread when scanned sideways or upside
down. Use the working orientation settings if your direction-sensitive codes will not usually be presented upright to the scanner.
Default = Upright.
Upright:
Vertical, Top to Bottom:
(Rotate CW 90°)
Upside Down:
Vertical, Bottom to Top:
(Rotate CCW 90°)
4 - 19
* Upright
Vertical, Bottom to Top
Upside Down
Vertical, Top to Bottom
4 - 20
5
Data Editing
Prefix/Suffix Overview
When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar
code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the
user-defined data into the message string.
Prefix and Suffix characters are data characters that can be sent before and after scanned data. You can specify if they should
be sent with all symbologies, or only with specific symbologies. The following illustration shows the breakdown of a message
string:
Prefix
Scanned Data
1-11
variable length
alpha numeric &
control characters
Suffix
1-11
alpha numeric &
control characters
Points to Keep In Mind
• It is not necessary to build a message string. The selections in this chapter are only used if you wish to alter the default
settings. Default prefix = None. Default suffix = None.
• A prefix or suffix may be added or cleared from one symbology or all symbologies.
• You can add any prefix or suffix from the ASCII Conversion Chart (Code Page 1252), beginning on page A-3, plus Code
I.D. and AIM I.D.
• You can string together several entries for several symbologies at one time.
• Enter prefixes and suffixes in the order in which you want them to appear on the output.
• When setting up for specific symbologies (as opposed to all symbologies), the specific symbology ID value counts as an
added prefix or suffix character.
• The maximum size of a prefix or suffix configuration is 200 characters, which includes header information.
To Add a Prefix or Suffix:
Step 1. Scan the Add Prefix or Add Suffix symbol (page 5-2).
Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in the Symbology Charts, beginning on page
A-1) for the symbology to which you want to apply the prefix or suffix. For example, for Code 128, Code ID is “j” and
Hex ID is “6A”.
Step 3. Scan the 2 hex digits from the Programming Chart inside the back cover of this manual or scan 9, 9 for all
symbologies.
Step 4. Determine the hex value from the ASCII Conversion Chart (Code Page 1252), beginning on page A-3, for the prefix
or suffix you wish to enter.
Note: To add the Code I.D., scan 5, C, 8, 0.
To add AIM I.D., scan 5, C, 8, 1.
To add a backslash (\), scan 5, C, 5, C.
To add a backslash (\), you must scan 5C twice – once to create the leading backslash and then to create the
backslash itself.
Step 5. Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual.
Step 6. Repeat Steps 4 and 5 for every prefix or suffix character.
Step 7. Scan Save to exit and save, or scan Discard to exit without saving.
Repeat Steps 1-6 to add a prefix or suffix for another symbology.
5-1
Example: Add a Tab Suffix to All Symbologies
Step 1. Scan Add Suffix.
Step 2. Scan 9, 9 from the Programming Chart inside the back cover of this manual to apply this suffix to all symbologies.
Step 3. Scan 0, 9 from the Programming Chart inside the back cover of this manual. This corresponds with the hex value
for a horizontal tab, shown in the ASCII Conversion Chart (Code Page 1252), beginning on page A-3.
Scan Save, or scan Discard to exit without saving.
To Clear One or All Prefixes or Suffixes
You can clear a single prefix or suffix, or clear all prefixes/suffixes for a symbology. If you have been entering prefixes and
suffixes for single symbologies, you can use Clear One Prefix (Suffix) to delete a specific character from a symbology.
When you Clear All Prefixes (Suffixes), all the prefixes or suffixes for a symbology are deleted.
Step 1. Scan the Clear One Prefix or Clear One Suffix symbol.
Step 2. Determine the 2 digit Hex value from the Symbology Chart (included in the Symbology Charts, beginning on page
A-1) for the symbology from which you want to clear the prefix or suffix.
Step 3. Scan the 2 digit hex value from the Programming Chart inside the back cover of this manual or scan 9, 9 for all
symbologies.
Your change is automatically saved.
To Add a Carriage Return Suffix to All Symbologies
Scan the following bar code if you wish to add a carriage return suffix to all symbologies at once. This action first clears all
current suffixes, then programs a carriage return suffix for all symbologies.
Add CR Suffix
All Symbologies
Prefix Selections
Add Prefix
Clear One Prefix
Clear All Prefixes
Suffix Selections
Add Suffix
5-2
Clear One Suffix
Clear All Suffixes
Function Code Transmit
When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function
code to the terminal. Charts of these function codes are provided in ASCII Conversion Chart (Code Page 1252) starting on
page A-3. When the scanner is in keyboard wedge mode, the scan code is converted to a key code before it is transmitted.
Default = Enable.
* Enable
Disable
Intercharacter, Interfunction, and Intermessage Delays
Some terminals drop information (characters) if data comes through too quickly. Intercharacter, interfunction, and intermessage
delays slow the transmission of data, increasing data integrity.
Intercharacter Delay
An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each
character of scanned data. Scan the Intercharacter Delay bar code below, then scan the number of 5ms delays, and the
Save bar code using the Programming Chart inside the back cover of this manual.
Prefix
Scanned Data
1
2
3
4
Suffix
5
Intercharacter Delay
Intercharacter Delay
To remove this delay, scan the Intercharacter Delay bar code, then set the number of delays to 0. Scan the Save bar code
using the Programming Chart inside the back cover of this manual.
Note: Intercharacter delays are not supported in USB serial emulation.
User Specified Intercharacter Delay
An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed after the transmission of a particular
character of scanned data. Scan the Delay Length bar code below, then scan the number of 5ms delays, and the Save
bar code using the Programming Chart inside the back cover of this manual.
5-3
Next, scan the Character to Trigger Delay bar code, tthen the 2-digit hex value for a printable character to trigger the
delay (see Lower ASCII Reference Table on page A-4).
Delay Length
Character to Trigger Delay
To remove this delay, scan the Delay Length bar code, and set the number of delays to 0. Scan the Save bar code using
the Programming Chart inside the back cover of this manual.
Interfunction Delay
An interfunction delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each
control character in the message string. Scan the Interfunction Delay bar code below, then scan the number of 5ms
delays, and the Save bar code using the Programming Chart inside the back cover of this manual.
Prefix
STX
1
Scanned Data
HT
2 3 4 5
Suffix
CR
LF
Interfunction Delays
Interfunction Delay
To remove this delay, scan the Interfunction Delay bar code, then set the number of delays to 0. Scan the Save bar code
using the Programming Chart inside the back cover of this manual.
Intermessage Delay
An intermessage delay of up to 5000 milliseconds (in 5ms increments) may be placed between each scan transmission.
Scan the Intermessage Delay bar code below, then scan the number of 5ms delays, and the Save bar code using the
Programming Chart inside the back cover of this manual.
1st Scan Transmission
2nd Scan Transmission
Intermessage Delay
Intermessage Delay
To remove this delay, scan the Intermessage Delay bar code, then set the number of delays to 0. Scan the Save bar code
using the Programming Chart inside the back cover of this manual.
5-4
6
Data Formatting
Data Format Editor Introduction
You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert
characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to
alter the output. Default Data Format setting = None.
Normally, when you scan a bar code, it is output automatically. However, when you create a format, you must use a “send” command (see Send Commands on page 6-3) within the format program to output data.
Multiple formats may be programmed into the scanner. They are stacked in the order in which they are entered. However, the
following list presents the order in which formats are applied:
1.
2.
3.
4.
5.
6.
7.
8.
Specific Terminal ID, Actual Code ID, Actual Length
Specific Terminal ID, Actual Code ID, Universal Length
Specific Terminal ID, Universal Code ID, Actual Length
Specific Terminal ID, Universal Code ID, Universal Length
Universal Terminal ID, Actual Code ID, Actual Length
Universal Terminal ID, Actual Code ID, Universal Length
Universal Terminal ID, Universal Code ID, Actual Length
Universal Terminal ID, Universal Code ID, Universal Length
The maximum size of a data format configuration is 2000 bytes, which includes header information.
If a bar code is read that fails the first data format, the next data format, if there is one, will be used on the bar code data. If there
is no other data format, the raw data is output.
If you have changed data format settings, and wish to clear all formats and return to the factory defaults, scan the Default Data
Format code below.
* Default Data Format
Add a Data Format
Step 1. Scan the Enter Data Format symbol (page 6-2).
Step 2. Select Primary/Alternate Format
Determine if this will be your primary data format, or one of 3 alternate formats. This allows you to save a total of 4
different data formats. To program your primary format, scan 0 using the Programming Chart inside the back cover of
this manual. If you are programming an alternate format, scan 1, 2, or 3, depending on which alternate format you are
programming. (See "Primary/Alternate Data Formats" on page 6-10 for further information.)
Step 3. Terminal Type
Refer to Terminal ID Table (page 6-3) and locate the Terminal ID number for your PC. Scan three numeric bar codes
on the inside back cover to program the scanner for your terminal ID (you must enter 3 digits). For example, scan 0 0
3 for an AT wedge.
Note: 099 indicates all terminal types.
Step 4. Code I.D.
In the Symbology Charts, beginning on page A-1, find the symbology to which you want to apply the data format. Locate
the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart inside the back cover of
this manual.
If you are creating a data format for Batch Mode Quantity, use 35 for the Code I.D.
Note: 99 indicates all symbologies.
6-1
Step 5. Length
Specify what length (up to 9999 characters) of data will be acceptable for this symbology. Scan the four digit data length
from the Programming Chart inside the back cover of this manual. For example, 50 characters is entered as 0050.
Note: 9999 indicates all lengths.
Step 6. Editor Commands
Refer to Data Format Editor Commands (page 6-3). Scan the symbols that represent the command you want to enter.
Step 7. Scan Save to save your data format, or Discard to exit without saving your changes.
Enter Data Format
Save
Discard
Other Programming Selections
Clear One Data Format
This deletes one data format for one symbology. If you are clearing the primary format, scan 0 from the Programming
Chart inside the back cover of this manual. If you are clearing an alternate format, scan 1, 2, or 3, depending on the
format you are clearing. Scan the Terminal Type and Code I.D. (see Symbology Charts on page A-1), and the bar code
data length for the specific data format that you want to delete. All other formats remain unaffected.
Clear all Data Formats
This clears all data formats.
Save to exit and save your data format changes.
Discard to exit without saving any data format changes.
Clear One Data Format
Clear All Data Formats
Save
Discard
6-2
Terminal ID Table
Terminal
USB
Serial
Keyboard
Model(s)
PC keyboard (HID)
Mac Keyboard
PC Keyboard (Japanese)
Serial (COM driver required)
HID POS
USB SurePOS Handheld
USB SurePOS Tabletop
RS232 TTL
RS232 True
RS485 (IBM-HHBCR 1+2, 46xx)
PS2 compatibles
AT compatibles
Terminal ID
124
125
134
130
131
128
129
000
000
051
003
002
Data Format Editor Commands
When working with the Data Format Editor, a virtual cursor is moved along your input data string. The following commands are
used to both move this cursor to different positions, and to select, replace, and insert data into the final output.
Send Commands
Send all characters
F1 Include in the output message all of the characters from the input message, starting from current cursor position,
followed by an insert character. Syntax = F1xx where xx stands for the insert character’s hex value for its ASCII code.
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.
Send a number of characters
F2 Include in the output message a number of characters followed by an insert character. Start from the current cursor
position and continue for “nn” characters or through the last character in the input message, followed by character “xx.”
Syntax = F2nnxx where nn stands for the numeric value (00-99) for the number of characters, and xx stands for the
insert character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on
page A-3 for decimal, hex and character codes.
F2 Example: Send a number of characters
Send the first 10 characters from the bar code above, followed by a carriage return. Command string: F2100D
F2 is the “Send a number of characters” command
10 is the number of characters to send
0D is the hex value for a CR
The data is output as: 1234567890
F2 and F1 Example: Split characters into 2 lines
Send the first 10 characters from the bar code above, followed by a carriage return, followed by the rest of the characters.
Command string: F2100DF10D
F2 is the “Send a number of characters” command
10 is the number of characters to send for the first line
0D is the hex value for a CR
6-3
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as:
1234567890
ABCDEFGHIJ
<CR>
Send all characters up to a particular character
F3 Include in the output message all characters from the input message, starting with the character at the current cursor
position and continuing to, but not including, the search character “ss,” followed by an insert character. The cursor is
moved forward to the “ss” character. Syntax = F3ssxx where ss stands for the search character’s hex value for its ASCII
code, and xx stands for the insert character’s hex value for its ASCII code.
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.
F3 Example: Send all characters up to a particular character
Using the bar code above, send all characters up to but not including “D,” followed by a carriage return.
Command string: F3440D
F3 is the “Send all characters up to a particular character” command
44 is the hex value for a 'D”
0D is the hex value for a CR
The data is output as:
1234567890ABC
<CR>
Send all but the last characters
E9 Include in the output message all but the last “nn” characters, starting from the current cursor position. The cursor is
moved forward to one position past the last input message character included. Syntax = E9nn where nn stands for the
numeric value (00-99) for the number of characters that will not be sent at the end of the message.
Insert a character multiple times
F4 Send “xx” character “nn” times in the output message, leaving the cursor in the current position. Syntax = F4xxnn where
xx stands for the insert character’s hex value for its ASCII code, and nn is the numeric value (00-99) for the number of
times it should be sent. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal,
hex and character codes.
E9 and F4 Example: Send all but the last characters, followed by 2 tabs
Send all characters except for the last 8 from the bar code above, followed by 2 tabs.
Command string: E908F40902
E9 is the “Send all but the last characters” command
08 is the number of characters at the end to ignore
F4 is the “Insert a character multiple times” command
09 is the hex value for a horizontal tab
02 is the number of times the tab character is sent
The data is output as: 1234567890AB <tab><tab>
6-4
Move Commands
Move the cursor forward a number of characters
F5 Move the cursor ahead “nn” characters from current cursor position.
Syntax = F5nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved ahead.
F5 Example: Move the cursor forward and send the data
Move the cursor forward 3 characters, then send the rest of the bar code data from the bar code above. End with a
carriage return.
Command string: F503F10D
F5 is the “Move the cursor forward a number of characters” command
03 is the number of characters to move the cursor
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as:
4567890ABCDEFGHIJ
<CR>
Move the cursor backward a number of characters
F6 Move the cursor back “nn” characters from current cursor position.
Syntax = F6nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved back.
Move the cursor to the beginning
F7 Move the cursor to the first character in the input message. Syntax = F7.
FE and F7 Example: Manipulate bar codes that begin with a 1
Search for bar codes that begin with a 1. If a bar code matches, move the cursor back to the beginning of the data and
send 6 characters followed by a carriage return. Using the bar code above:
Command string: FE31F7F2060D
FE is the “Compare characters” command
31 is the hex value for 1
F7 is the “Move the cursor to the beginning” command
F2 is the “Send a number of characters” command
06 is the number of characters to send
0D is the hex value for a CR
The data is output as:
123456
<CR>
Move the cursor to the end
EA Move the cursor to the last character in the input message. Syntax = EA.
6-5
Search Commands
Search forward for a character
F8 Search the input message forward for “xx” character from the current cursor position, leaving the cursor pointing to the
“xx” character. Syntax = F8xx where xx stands for the search character’s hex value for its ASCII code.
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.
F8 Example: Send bar code data that starts after a particular character
Search for the letter “D” in bar codes and send all the data that follows, including the “D.” Using the bar code above:
Command string: F844F10D
F8 is the “Search forward for a character” command
44 is the hex value for “D”
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as:
DEFGHIJ
<CR>
Search backward for a character
F9 Search the input message backward for “xx” character from the current cursor position, leaving the cursor pointing to
the “xx” character. Syntax = F9xx where xx stands for the search character’s hex value for its ASCII code.
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.
Search forward for a non-matching character
E6 Search the input message forward for the first non-“xx” character from the current cursor position, leaving the cursor
pointing to the non-“xx” character. Syntax = E6xx where xx stands for the search character’s hex value for its ASCII
code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character
codes.
E6 Example: Remove zeroes at the beginning of bar code data
This example shows a bar code that has been zero filled. You may want to ignore the zeroes and send all the data that
follows. E6 searches forward for the first character that is not zero, then sends all the data after, followed by a carriage
return. Using the bar code above:
Command string: E630F10D
E6 is the “Search forward for a non-matching character” command
30 is the hex value for 0
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as:
37692
<CR>
Search backward for a non-matching character
E7 Search the input message backward for the first non-“xx” character from the current cursor position, leaving the cursor
pointing to the non-“xx” character. Syntax = E7xx where xx stands for the search character’s hex value for its ASCII
code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character
codes.
6-6
Miscellaneous Commands
Suppress characters
FB Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the cursor is
advanced by other commands. When the FC command is encountered, the suppress function is terminated. The
cursor is not moved by the FB command.
Syntax = FBnnxxyy . .zz where nn is a count of the number of suppressed characters in the list, and xxyy .. zz is the list
of characters to be suppressed.
FB Example: Remove spaces in bar code data
This example shows a bar code that has spaces in the data. You may want to remove the spaces before sending the
data. Using the bar code above:
Command string: FB0120F10D
FB is the “Suppress characters” command
01 is the number of character types to be suppressed
20 is the hex value for a space
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as:
34567890
<CR>
Stop suppressing characters
FC Disables suppress filter and clear all suppressed characters. Syntax = FC.
Replace characters
E4 Replaces up to 15 characters in the output message, without moving the cursor. Replacement continues until the E5
command is encountered. Syntax = E4nnxx1xx2yy1yy2...zz1zz2 where nn is the total count of the number of characters
in the list (characters to be replaced plus replacement characters); xx1 defines characters to be replaced and xx2 defines
replacement characters, continuing through zz1 and zz2.
E4 Example: Replace zeroes with CRs in bar code data
If the bar code has characters that the host application does not want included, you can use the E4 command to
replace those characters with something else. In this example, you will replace the zeroes in the bar code above with
carriage returns.
Command string: E402300DF10D
E4 is the “Replace characters” command
02 is the total count of characters to be replaced, plus the replacement characters (0 is replaced by CR, so total characters = 2)
30 is the hex value for 0
0D is the hex value for a CR (the character that will replace the 0)
F1 is the “Send all characters” command
0D is the hex value for a CR
6-7
The data is output as:
1234
5678
ABC
<CR>
Stop replacing characters
E5 Terminates character replacement. Syntax = E5.
Compare characters
FE Compare the character in the current cursor position to the character “xx.” If characters are equal, move the cursor
forward one position. Syntax = FExx where xx stands for the comparison character’s hex value for its ASCII code.
Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-3 for decimal, hex and character codes.
Check for a number
EC Check to make sure there is an ASCII number at the current cursor position. The format is aborted if the character is
not numeric.
EC Example: Only output the data if the bar code begins with a number
If you want only data from bar codes that begin with a number, you can use EC to check for the number.
Command string: ECF10D
EC is the “Check for a number” command
F1 is the “Send all characters” command
0D is the hex value for a CR
If this bar code is read,
the next data format, if there is one, will be used on the data. If there
is no other format, the format fails and the raw data is output as AB1234.
If this bar code is read:
the data is output as:
1234AB
<CR>
Check for non-numeric character
ED Check to make sure there is a non-numeric ASCII character at the current cursor position. The format is aborted if the
character is numeric.
ED Example: Only output the data if the bar code begins with a letter
If you want only data from bar codes that begin with a letter, you can use ED to check for the letter.
Command string: EDF10D
ED is the “Check for a non-numeric character” command
F1 is the “Send all characters” command
0D is the hex value for a CR
If this bar code is read,
the next data format, if there is one, will be used on this data. If there
is no other format, the format fails and the raw data is output as 1234AB.
If this bar code is read:
AB1234
<CR>
6-8
the data is output as:
Insert a delay
EF Inserts a delay of up to 49,995 milliseconds (in multiples of 5), starting from the current cursor position. Syntax = EFnnnn
where nnnn stands for the delay in 5ms increments, up to 9999. This command can only be used with keyboard
emulation.
Data Formatter
When Data Formatter is turned Off, the bar code data is output to the host as read, including prefixes and suffixes.
Data Formatter Off
You may wish to require the data to conform to a data format you have created and saved. The following settings can be applied
to your data format:
Data Formatter On, Not Required, Keep Prefix/Suffix
Scanned data is modified according to your data format, and prefixes and suffixes are transmitted.
Data Formatter On, Not Required, Drop Prefix/Suffix
Scanned data is modified according to your data format. If a data format is found for a particular symbol, those prefixes and
suffixes are not transmitted. If a data format is not found for that symbol, the prefixes and suffixes are transmitted.
Data Format Required, Keep Prefix/Suffix
Scanned data is modified according to your data format, and prefixes and suffixes are transmitted. Any data that does not
match your data format requirements generates an error tone and the data in that bar code is not transmitted. If you wish
to process this type of bar code without generating an error tone, see Data Format Non-Match Error Tone.
Data Format Required, Drop Prefix/Suffix
Scanned data is modified according to your data format. If a data format is found for a particular symbol, those prefixes and
suffixes are not transmitted. Any data that does not match your data format requirements generates an error tone. If you
wish to process this type of bar code without generating an error tone, see Data Format Non-Match Error Tone.
Choose one of the following options. Default = Data Formatter On, Not Required, Keep Prefix/Suffix.
* Data Formatter On,
Not Required,
Keep Prefix/Suffix
Data Formatter On,
Not Required,
Drop Prefix/Suffix
Data Format Required,
Keep Prefix/Suffix
Data Format Required,
Drop Prefix/Suffix
6-9
Data Format Non-Match Error Tone
When a bar code is encountered that doesn’t match your required data format, the scanner normally generates an error
tone. However, you may want to continue scanning bar codes without hearing the error tone. If you scan the Data Format
Non-Match Error Tone Off bar code, data that doesn’t conform to your data format is not transmitted, and no error tone will
sound. If you wish to hear the error tone when a non-matching bar code is found, scan the Data Format Non-Match Error
Tone On bar code. Default = Data Format Non-Match Error Tone On.
* Data Format Non-Match Error
Tone On
Data Format Non-Match
Error Tone Off
Primary/Alternate Data Formats
You can save up to four data formats, and switch between these formats. Your primary data format is saved under 0. Your other
three formats are saved under 1, 2, and 3. To set your device to use one of these formats, scan one of the bar codes below.
Primary Data Format
Data Format 1
Data Format 2
Data Format 3
Single Scan Data Format Change
You can also switch between data formats for a single scan. The next bar code is scanned using an alternate data format,
then reverts to the format you have selected above (either Primary, 1, 2, or 3).
6 - 10
For example, you may have set your device to the data format you saved as Data Format 3. You can switch to Data Format
1 for a single button press by scanning the Single Scan-Data Format 1 bar code below. The next bar code that is scanned
uses Data Format 1, then reverts back to Data Format 3.
Single Scan-Primary
Data Format
Single Scan-Data Format 1
Single Scan-Data Format 2
Single Scan-Data Format 3
6 - 11
6 - 12
7
Symbologies
This programming section contains the following menu selections. Refer to Chapter 9 for settings and defaults.
• All Symbologies
• Interleaved 2 of 5
• Aztec Code
• Korea Post
• China Post (Hong Kong 2 of 5)
• Matrix 2 of 5
• Chinese Sensible (Han Xin) Code
• MaxiCode
• Codabar
• MicroPDF417
• Codablock A
• MSI
• Codablock F
• NEC 2 of 5
• Code 11
• Postal Codes - 2D
• Code 128
• Postal Codes - Linear
• Code 32 Pharmaceutical (PARAF)
• PDF417
• Code 39
• GS1 DataBar Omnidirectional
• Code 93
• QR Code
• Data Matrix
• Straight 2 of 5 IATA (two-bar start/stop)
• EAN/JAN-13
• Straight 2 of 5 Industrial (three-bar start/stop)
• EAN/JAN-8
• TCIF Linked Code 39 (TLC39)
• GS1 Composite Codes
• Telepen
• GS1 DataBar Expanded
• Trioptic Code
• GS1 DataBar Limited
• UPC-A
• GS1 DataBar Omnidirectional
• UPC-A/EAN-13 with Extended Coupon Code
• GS1 Emulation
• UPC-E0
• GS1-128
• UPC-E1
Note: The selections in this User’s Guide are dependent on the Voyager 1602g model you have purchased. PDF and 2
dimensional bar codes can only be read by model 1602g2D and cannot be read by model 1602g1D.
All Symbologies
If you want to decode all the symbologies allowable for your scanner, scan the All Symbologies On code. If on the other hand,
you want to decode only a particular symbology, scan All Symbologies Off followed by the On symbol for that particular symbology. Default = All Symbologies Off.
All Symbologies On
All Symbologies Off
Note: Scanner performance may be degraded after scanning All Symbologies On. Only scan All Symbologies On when
needed.
Note: When All Symbologies On is scanned, 2D Postal Codes are not enabled. 2D Postal Codes must be enabled separately.
7-1
Message Length Description
You are able to set the valid reading length of some of the bar code symbologies. You may wish to set the same value for minimum and maximum length to force the scanner to read fixed length bar code data. This helps reduce the chances of a misread.
EXAMPLE:
Decode only those bar codes with a count of 9-20 characters.
Min. length = 09Max. length = 20
EXAMPLE: Decode only those bar codes with a count of 15 characters.
Min. length = 15Max. length = 15
For a value other than the minimum and maximum message length defaults, scan the bar codes included in the explanation of
the symbology, then scan the digit value of the message length and Save bar codes on the Programming Chart inside the back
cover of this manual. The minimum and maximum lengths and the defaults are included with the respective symbologies.
Codabar
<Default All Codabar Settings>
Codabar On/Off
* On
Off
Codabar Start/Stop Characters
Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/
Stop characters. Default = Don’t Transmit.
Transmit
* Don’t Transmit
Codabar Check Character
Codabar check characters are created using different “modulos.” You can program the scanner to read only Codabar bar
codes with Modulo 16 check characters. Default = No Check Character.
No Check Character indicates that the scanner reads and transmits bar code data with or without a check character.
When Check Character is set to Validate and Transmit, the scanner will only read Codabar bar codes printed with a check
character, and will transmit this character at the end of the scanned data.
7-2
When Check Character is set to Validate, but Don’t Transmit, the unit will only read Codabar bar codes printed with a
check character, but will not transmit the check character with the scanned data.
* No Check Character
Validate Modulo 16, but
Don’t Transmit
Validate Modulo 16
and Transmit
Codabar Concatenation
Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having
a “D” start character, adjacent to a symbol having a “D” stop character. In this case the two messages are concatenated
into one with the “D” characters omitted.
A 1 2 3 4 D
D 5 6 7 8 A
Select Require to prevent the scanner from decoding a single “D” Codabar symbol without its companion. This selection
has no effect on Codabar symbols without Stop/Start D characters.
On
* Off
Require
Codabar Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 2-60. Minimum Default = 4, Maximum Default = 60.
Minimum Message Length
7-3
Maximum Message Length
Code 39
< Default All Code 39 Settings >
Code 39 On/Off
* On
Off
Code 39 Start/Stop Characters
Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/
Stop characters. Default = Don’t Transmit.
Transmit
* Don’t Transmit
Code 39 Check Character
No Check Character indicates that the scanner reads and transmits bar code data with or without a check character.
When Check Character is set to Validate, but Don’t Transmit, the unit only reads Code 39 bar codes printed with a check
character, but will not transmit the check character with the scanned data.
When Check Character is set to Validate and Transmit, the scanner only reads Code 39 bar codes printed with a check
character, and will transmit this character at the end of the scanned data. Default = No Check Character.
* No Check Character
7-4
Validate, but Don’t Transmit
Validate and Transmit
Code 39 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 0-48. Minimum Default = 0, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
Code 39 Append
This function allows the scanner to append the data from several Code 39 bar codes together before transmitting them to
the host computer. When the scanner encounters a Code 39 bar code with the append trigger character(s), it buffers Code
39 bar codes until it reads a Code 39 bar code that does not have the append trigger. The data is then transmitted in the
order in which the bar codes were read (FIFO). Default = Off.
On
* Off
Code 32 Pharmaceutical (PARAF)
Code 32 Pharmaceutical is a form of the Code 39 symbology used by Italian pharmacies. This symbology is also known as
PARAF.
Note: Trioptic Code (page 7-32) must be turned off while scanning Code 32 Pharmaceutical codes.
On
* Off
7-5
Full ASCII
If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single
character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #.
Default = Off.
NUL %U
DLE $P
SP
SPACE 0
0
@
%V
P
P
‘
%W p
+P
SOH $A
DC1 $Q
!
/A
1
1
A
A
Q
Q
a
+A
q
+Q
STX $B
DC2 $R
“
/B
2
2
B
B
R
R
b
+B
r
+R
ETX $C
DC3 $S
#
/C
3
3
C
C
S
S
c
+C
s
+S
EOT $D
DC4 $T
$
/D
4
4
D
D
T
T
d
+D
t
+T
ENQ $E
NAK $U
%
/E
5
5
E
E
U
U
e
+E
u
+U
ACK $F
SYN $V
&
/F
6
6
F
F
V
V
f
+F
v
+V
BEL $G
ETB $W
‘
/G
7
7
G
G
W
W
g
+G
w
+W
BS
$H
CAN $X
(
/H
8
8
H
H
X
X
h
+H
x
+X
HT
$I
EM
$Y
)
/I
9
9
I
I
Y
Y
i
+I
y
+Y
LF
$J
SUB $Z
*
/J
:
/Z
J
J
Z
Z
j
+J
z
+Z
VT
$K
ESC %A
+
/K
;
%F
K
K
[
%K
k
+K
{
%P
FF
$L
FS
%B
,
/L
<
%G L
L
\
%L
l
+L
|
%Q
CR
$M
GS
%C
-
-
=
%H
M
M
]
%M m
+M
}
%R
SO
$N
RS
%D
.
.
>
%I
N
N
^
%N
n
+N
~
%S
SI
$O
US
%E
/
/O
?
%J
O
O
_
%O o
+O
DEL %T
Character pairs /M and /N decode as a minus sign and period respectively.
Character pairs /P through /Y decode as 0 through 9.
Full ASCII On
* Full ASCII Off
Code 39 Code Page
Code pages define the mapping of character codes to characters. If the data received does not display with the proper
characters, it may be because the bar code being scanned was created using a code page that is different from the one the
host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar codes were
created (see ISO 2022/ISO 646 Character Replacements on page A-7), and scan the value and the Save bar code from
the Programming Chart on the inside the back cover of this manual. The data characters should then appear properly.
Code 39 Code Page
7-6
Interleaved 2 of 5
< Default All Interleaved 2 of 5 Settings >
Interleaved 2 of 5 On/Off
* On
Off
Check Digit
No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit.
When Check Digit is set to Validate, but Don’t Transmit, the unit only reads Interleaved 2 of 5 bar codes printed with a
check digit, but will not transmit the check digit with the scanned data.
When Check Digit is set to Validate and Transmit, the scanner only reads Interleaved 2 of 5 bar codes printed with a
check digit, and will transmit this digit at the end of the scanned data. Default = No Check Digit.
* No Check Digit
Validate, but Don’t Transmit
Validate and Transmit
Interleaved 2 of 5 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
7-7
Maximum Message Length
NEC 2 of 5
< Default All NEC 2 of 5 Settings >
NEC 2 of 5 On/Off
* On
Off
Check Digit
No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit.
When Check Digit is set to Validate, but Don’t Transmit, the unit only reads NEC 2 of 5 bar codes printed with a check
digit, but will not transmit the check digit with the scanned data.
When Check Digit is set to Validate and Transmit, the scanner only reads NEC 2 of 5 bar codes printed with a check digit,
and will transmit this digit at the end of the scanned data. Default = No Check Digit.
* No Check Digit
Validate, but Don’t Transmit
Validate and Transmit
7-8
NEC 2 of 5 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
Code 93
< Default All Code 93 Settings >
Code 93 On/Off
* On
Off
Code 93 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
7-9
Code 93 Append
This function allows the scanner to append the data from several Code 93 bar codes together before transmitting them to
the host computer. When this function is enabled, the scanner stores those Code 93 bar codes that start with a space
(excluding the start and stop symbols), and does not immediately transmit the data. The scanner stores the data in the
order in which the bar codes are read, deleting the first space from each. The scanner transmits the appended data when
it reads a Code 93 bar code that starts with a character other than a space. Default = Off.
On
* Off
Code 93 Code Page
Code pages define the mapping of character codes to characters. If the data received does not display with the proper
characters, it may be because the bar code being scanned was created using a code page that is different from the one the
host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar codes were
created (see ISO 2022/ISO 646 Character Replacements on page A-7), and scan the value and the Save bar code from
the Programming Chart on the inside the back cover of this manual. The data characters should then appear properly.
Code 93 Code Page
7 - 10
Straight 2 of 5 Industrial (three-bar start/stop)
<Default All Straight 2 of 5 Industrial Settings>
Straight 2 of 5 Industrial On/Off
On
* Off
Straight 2 of 5 Industrial Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
7 - 11
Straight 2 of 5 IATA (two-bar start/stop)
<Default All Straight 2 of 5 IATA Settings>
Straight 2 of 5 IATA On/Off
On
* Off
Straight 2 of 5 IATA Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 1-48. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
7 - 12
Matrix 2 of 5
<Default All Matrix 2 of 5 Settings>
Matrix 2 of 5 On/Off
On
* Off
Matrix 2 of 5 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
7 - 13
Code 11
<Default All Code 11 Settings>
Code 11 On/Off
On
* Off
Check Digits Required
This option sets whether 1 or 2 check digits are required with Code 11 bar codes. Default = Two Check Digits.
One Check Digit
* Two Check Digits
Code 11 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 1-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
7 - 14
Code 128
<Default All Code 128 Settings>
Code 128 On/Off
* On
Off
ISBT 128 Concatenation
In 1994 the International Society of Blood Transfusion (ISBT) ratified a standard for communicating critical blood information in a uniform manner. The use of ISBT formats requires a paid license. The ISBT 128 Application Specification
describes 1) the critical data elements for labeling blood products, 2) the current recommendation to use Code 128 due to
its high degree of security and its space-efficient design, 3) a variation of Code 128 that supports concatenation of neighboring symbols, and 4) the standard layout for bar codes on a blood product label. Use the bar codes below to turn concatenation on or off. Default =Off.
On
* Off
Code 128 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 0-80. Minimum Default = 0, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
7 - 15
Code 128 Append
This function allows the scanner to append the data from several Code 128 bar codes together before transmitting them to
the host computer. When the scanner encounters a Code 128 bar code with the append trigger character(s), it buffers
Code 128 bar codes until it reads a Code 128 bar code that does not have the append trigger. The data is then transmitted
in the order in which the bar codes were read (FIFO). Default = On.
* On
Off
Code 128 Code Page
Code pages define the mapping of character codes to characters. If the data received does not display with the proper
characters, it may be because the bar code being scanned was created using a code page that is different from the one the
host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar codes were
created (see ISO 2022/ISO 646 Character Replacements on page A-7), and scan the value and the Save bar code from
the Programming Chart on the inside the back cover of this manual. The data characters should then appear properly.
Code 128 Code Page
7 - 16
GS1-128
<Default All GS1-128 Settings>
GS1-128 On/Off
* On
Off
GS1-128 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 1-80. Minimum Default = 1, Maximum Default = 80.
Minimum Message Length
Maximum Message Length
7 - 17
Telepen
<Default All Telepen Settings>
Telepen On/Off
On
* Off
Telepen Output
Using AIM Telepen Output, the scanner reads symbols with start/stop pattern 1 and decodes them as standard full ASCII
(start/stop pattern 1). When Original Telepen Output is selected, the scanner reads symbols with start/stop pattern 1 and
decodes them as compressed numeric with optional full ASCII (start/stop pattern 2). Default = AIM Telepen Output.
* AIM Telepen Output
Original Telepen Output
Telepen Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 1-60. Minimum Default = 1, Maximum Default = 60.
Minimum Message Length
Maximum Message Length
7 - 18
UPC-A
<Default All UPC-A Settings>
UPC-A On/Off
* On
Off
Note: To convert UPC-A bar codes to EAN-13, see Convert UPC-A to EAN-13 on page 7-24.
UPC-A Check Digit
This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not.
Default = On.
* On
Off
UPC-A Number System
The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can
be programmed so it will not transmit it. Default = On.
* On
Off
7 - 19
UPC-A Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC-A data.
Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
* 5 Digit Addenda Off
UPC-A Addenda Required
When Required is scanned, the scanner will only read UPC-A bar codes that have addenda. You must then turn on a 2 or
5 digit addenda listed on page 7-20. Default = Not Required.
Required
* Not Required
UPC-A Addenda Separator
When this feature is on, there is a space between the data from the bar code and the data from the addenda. When turned
off, there is no space. Default = On.
* On
Off
7 - 20
UPC-A/EAN-13 with Extended Coupon Code
Use the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code. When left on the default setting
(Off), the scanner treats Coupon Codes and Extended Coupon Codes as single bar codes.
If you scan the Allow Concatenation code, when the scanner sees the coupon code and the extended coupon code in a single
scan, it transmits both as one symbology. Otherwise, it transmits the first coupon code it reads.
If you scan the Require Concatenation code, the scanner must see and read the coupon code and extended coupon code in a
single read to transmit the data. No data is output unless both codes are read. Default = Off.
* Off
Allow Concatenation
Require Concatenation
Coupon GS1 DataBar Output
If you scan coupons that have both UPC and GS1 DataBar codes, you may wish to scan and output only the data from the GS1
DataBar code. Scan the GS1 Output On code below to scan and output only the GS1 DataBar code data. Default = GS1 Output Off.
* GS1 Output Off
GS1 Output On
7 - 21
UPC-E0
<Default All UPC-E Settings>
UPC-E0 On/Off
Most U.P.C. bar codes lead with the 0 number system. To read these codes, use the UPC-E0 On selection. If you need to
read codes that lead with the 1 number system, use UPC-E1 (page 7-24). Default = On.
* UPC-E0 On
UPC-E0 Off
UPC-E0 Expand
UPC-E Expand expands the UPC-E code to the 12 digit, UPC-A format. Default = Off.
On
* Off
UPC-E0 Addenda Required
When Required is scanned, the scanner will only read UPC-E bar codes that have addenda. Default = Not Required.
Required
* Not Required
7 - 22
UPC-E0 Addenda Separator
When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned
Off, there is no space. Default = On.
* On
Off
UPC-E0 Check Digit
Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not. Default = On.
* On
Off
UPC-E0 Leading Zero
This feature allows the transmission of a leading zero (0) at the beginning of scanned data. To prevent transmission, scan
Off. Default = On.
* On
Off
UPC-E0 Addenda
This selection adds 2 or 5 digits to the end of all scanned UPC-E data. Default = Off for both 2 Digit and 5 Digit Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
7 - 23
5 Digit Addenda On
* 5 Digit Addenda Off
UPC-E1
Most U.P.C. bar codes lead with the 0 number system. For these codes, use UPC-E0 (page 7-22). If you need to read codes
that lead with the 1 number system, use the UPC-E1 On selection. Default = Off.
UPC-E1 On
* UPC-E1 Off
EAN/JAN-13
<Default All EAN/JAN Settings>
EAN/JAN-13 On/Off
* On
Off
Convert UPC-A to EAN-13
When UPC-A Converted to EAN-13 is selected, UPC-A bar codes are converted to 13 digit EAN-13 codes by adding a
zero to the front. When Do not Convert UPC-A is selected, UPC-A codes are read as UPC-A.
UPC-A Converted to EAN-13
7 - 24
* Do not Convert UPC-A
EAN/JAN-13 Check Digit
This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not.
Default = On.
* On
Off
EAN/JAN-13 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit
Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
* 5 Digit Addenda Off
EAN/JAN-13 Addenda Required
When Required is scanned, the scanner will only read EAN/JAN-13 bar codes that have addenda. Default = Not Required.
Required
7 - 25
* Not Required
EAN/JAN-13 Addenda Separator
When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned
Off, there is no space. Default = On.
* On
Off
Note: If you want to enable or disable EAN13 with Extended Coupon Code, refer to UPC-A/EAN-13 with Extended Coupon
Code (page 7-21).
ISBN Translate
When On is scanned, EAN-13 Bookland symbols are translated into their equivalent ISBN number format. Default = Off.
On
* Off
7 - 26
EAN/JAN-8
<Default All EAN/JAN-8 Settings>
EAN/JAN-8 On/Off
* On
Off
EAN/JAN-8 Check Digit
This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not.
Default = On.
* On
Off
EAN/JAN-8 Addenda
This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Default = Off for both 2 Digit and 5 Digit
Addenda.
2 Digit Addenda On
* 2 Digit Addenda Off
5 Digit Addenda On
7 - 27
* 5 Digit Addenda Off
EAN/JAN-8 Addenda Required
When Required is scanned, the scanner will only read EAN/JAN-8 bar codes that have addenda. Default = Not Required.
Required
* Not Required
EAN/JAN-8 Addenda Separator
When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned
Off, there is no space. Default = On.
* On
Off
7 - 28
MSI
<Default All MSI Settings>
MSI On/Off
On
* Off
MSI Check Character
Different types of check characters are used with MSI bar codes. You can program the scanner to read MSI bar codes with
Type 10 check characters. Default = Validate Type 10, but Don’t Transmit.
When Check Character is set to Validate Type 10/11 and Transmit, the scanner will only read MSI bar codes printed with
the specified type check character(s), and will transmit the character(s) at the end of the scanned data.
When Check Character is set to Validate Type 10/11, but Don’t Transmit, the unit will only read MSI bar codes printed
with the specified type check character(s), but will not transmit the check character(s) with the scanned data.
* Validate Type 10, but Don’t
Transmit
Validate Type 10 and Transmit
Validate 2 Type 10 Characters,
but Don’t Transmit
Validate 2 Type 10 Characters
and Transmit
Validate Type 11 then Type 10
Character, but Don’t Transmit
7 - 29
Validate Type 11 then
Type 10 Character and Transmit
Disable MSI Check Characters
MSI Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 4-48. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
7 - 30
GS1 DataBar Omnidirectional
< Default All GS1 DataBar Omnidirectional Settings >
GS1 DataBar Omnidirectional On/Off
* On
Off
GS1 DataBar Limited
< Default All GS1 DataBar Limited Settings >
GS1 DataBar Limited On/Off
* On
Off
7 - 31
GS1 DataBar Expanded
< Default All GS1 DataBar Expanded Settings >
GS1 DataBar Expanded On/Off
* On
Off
GS1 DataBar Expanded Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 4-74. Minimum Default = 4, Maximum Default = 74.
Minimum Message Length
Maximum Message Length
Trioptic Code
Note: If you are going to scan Code 32 Pharmaceutical codes (page 7-5), Trioptic Code must be off.
Trioptic Code is used for labeling magnetic storage media.
On
* Off
7 - 32
Codablock A
<Default All Codablock A Settings>
Codablock A On/Off
On
* Off
Codablock A Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 1-600. Minimum Default = 1, Maximum Default = 600.
Minimum Message Length
Maximum Message Length
7 - 33
Codablock F
<Default All Codablock F Settings>
Codablock F On/Off
On
* Off
Codablock F Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 1-2048. Minimum Default = 1, Maximum Default = 2048.
Minimum Message Length
Maximum Message Length
Label Code
The standard Label Code is used in libraries. Default = Off.
On
*Off
7 - 34
PDF417
< Default All PDF417 Settings >
PDF417 On/Off
* On
Off
PDF417 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 1-2750. Minimum Default = 1, Maximum Default = 2750.
Minimum Message Length
Maximum Message Length
MacroPDF417
MacroPDF417 is an implementation of PDF417 capable of encoding very large amounts of data into multiple PDF417 bar
codes. When this selection is enabled, these multiple bar codes are assembled into a single data string. Default = On.
* On
Off
7 - 35
MicroPDF417
< Default All MicroPDF417 Settings >
MicroPDF417 On/Off
On
* Off
MicroPDF417 Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 1-366. Minimum Default = 1, Maximum Default = 366.
Minimum Message Length
Maximum Message Length
GS1 Composite Codes
Linear codes are combined with a unique 2D composite component to form a new class called GS1 Composite symbology.
GS1 Composite symbologies allow for the co-existence of symbologies already in use. Default = Off.
On
* Off
7 - 36
UPC/EAN Version
Scan the UPC/EAN Version On bar code to decode GS1 Composite symbols that have a U.P.C. or an EAN linear component. (This does not affect GS1 Composite symbols with a GS1-128 or GS1 linear component.) Default = UPC/EAN Version Off.
UPC/EAN Version On
* UPC/EAN Version Off
Note: If you scan coupons that have both UPC and GS1 DataBar codes, you may wish to scan and output only the data from
the GS1 DataBar code. See Coupon GS1 DataBar Output (page 7-21) for further information.
GS1 Composite Code Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 1-2435. Minimum Default = 1, Maximum Default = 2435.
Minimum Message Length
Maximum Message Length
GS1 Emulation
The scanner can automatically format the output from any GS1 data carrier to emulate what would be encoded in an equivalent
GS1-128 or GS1 DataBar symbol. GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8, ITF-14, GS1-128, and
GS1-128 DataBar and GS1 Composites. (Any application that accepts GS1 data can be simplified since it only needs to recognize one data carrier type.)
If GS1-128 Emulation is scanned, all retail codes (U.P.C., UPC-E, EAN8, EAN13) are expanded out to 16 digits. If the AIM ID
is enabled, the value will be the GS1-128 AIM ID, ]C1 (see Symbology Charts on page A-1).
If GS1 DataBar Emulation is scanned, all retail codes (U.P.C., UPC-E, EAN8, EAN13) are expanded out to 16 digits. If the AIM
ID is enabled, the value will be the GS1-DataBar AIM ID, ]em (see Symbology Charts on page A-1).
If GS1 Code Expansion Off is scanned, retail code expansion is disabled, and UPC-E expansion is controlled by the UPC-E0
Expand (page 7-22) setting. If the AIM ID is enabled, the value will be the GS1-128 AIM ID, ]C1 (see Symbology Charts on
page A-1).
If EAN8 to EAN13 Conversion is scanned, all EAN8 bar codes are converted to EAN13 format.
Default = GS1 Emulation Off.
GS1-128 Emulation
7 - 37
GS1 DataBar Emulation
GS1 Code Expansion Off
EAN8 to EAN13 Conversion
* GS1 Emulation Off
TCIF Linked Code 39 (TLC39)
This code is a composite code since it has a Code 39 linear component and a MicroPDF417 stacked code component. All bar
code readers are capable of reading the Code 39 linear component. The MicroPDF417 component can only be decoded if
TLC39 On is selected. The linear component may be decoded as Code 39 even if TLC39 is off. Default = Off.
On
* Off
QR Code
< Default All QR Code Settings >
QR Code On/Off
This selection applies to both QR Code and Micro QR Code.
* On
Off
7 - 38
QR Code Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 1-7089. Minimum Default = 1, Maximum Default = 7089.
Minimum Message Length
Maximum Message Length
QR Code Append
This function allows the scanner to append the data from several QR Code bar codes together before transmitting them to
the host computer. When the scanner encounters an QR Code bar code with the append trigger character(s), it buffers the
number of QR Code bar codes determined by information encoded in those bar codes. Once the proper number of codes
is reached, the data is output in the order specified in the bar codes. Default = On.
* On
Off
QR Code Page
QR Code pages define the mapping of character codes to characters. If the data received does not display with the proper
characters, it may be because the bar code being scanned was created using a code page that is different from the one the
host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar codes were
created (see ISO 2022/ISO 646 Character Replacements on page A-7), and scan the value and the Save bar code from
the Programming Chart on the inside the back cover of this manual. The data characters should then appear properly.
QR Code Page
7 - 39
Data Matrix
< Default All Data Matrix Settings >
Data Matrix On/Off
* On
Off
Data Matrix Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 1-3116. Minimum Default = 1, Maximum Default = 3116.
Minimum Message Length
Maximum Message Length
Data Matrix Append
This function allows the scanner to append the data from several Data Matrix bar codes together before transmitting them
to the host computer. When the scanner encounters an Data Matrix bar code with the append trigger character(s), it buffers the number of Data Matrix bar codes determined by information encoded in those bar codes. Once the proper number
of codes is reached, the data is output in the order specified in the bar codes. Default = On.
* On
Off
Data Matrix Code Page
Data Matrix Code pages define the mapping of character codes to characters. If the data received does not display with the
proper characters, it may be because the bar code being scanned was created using a code page that is different from the
one the host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar
7 - 40
codes were created (see ISO 2022/ISO 646 Character Replacements on page A-7), and scan the value and the Save bar
code from the Programming Chart on the inside the back cover of this manual. The data characters should then appear
properly.
Data Matrix Code Page
MaxiCode
< Default All MaxiCode Settings >
MaxiCode On/Off
On
* Off
MaxiCode Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 1-150. Minimum Default = 1, Maximum Default = 150.
Minimum Message Length
Maximum Message Length
7 - 41
Aztec Code
< Default All Aztec Code Settings >
Aztec Code On/Off
* On
Off
Aztec Code Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 1-3832. Minimum Default = 1, Maximum Default = 3832.
Minimum Message Length
Maximum Message Length
Aztec Append
This function allows the scanner to append the data from several Aztec bar codes together before transmitting them to the
host computer. When the scanner encounters an Aztec bar code with the append trigger character(s), it buffers the number
of Aztec bar codes determined by information encoded in those bar codes. Once the proper number of codes is reached,
the data is output in the order specified in the bar codes. Default = On.
* On
Off
Aztec Code Page
Aztec Code pages define the mapping of character codes to characters. If the data received does not display with the
proper characters, it may be because the bar code being scanned was created using a code page that is different from the
one the host program is expecting. If this is the case, scan the bar code below, select the code page with which the bar
7 - 42
codes were created (see ISO 2022/ISO 646 Character Replacements on page A-7), and scan the value and the Save bar
code from the Programming Chart on the inside the back cover of this manual. The data characters should then appear
properly.
Aztec Code Page
Chinese Sensible (Han Xin) Code
< Default All Han Xin Settings >
Han Xin Code On/Off
On
* Off
Han Xin Code Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional
information. Minimum and Maximum lengths = 1-7833. Minimum Default = 1, Maximum Default = 7833.
Minimum Message Length
Maximum Message Length
7 - 43
Postal Codes - 2D
The following lists the possible 2D postal codes, and 2D postal code combinations that are allowed. Only one 2D postal code
selection can be active at a time. If you scan a second 2D postal code selection, the first selection is overwritten. Default = 2D
Postal Codes Off.
* 2D Postal Codes Off
Single 2D Postal Codes:
Australian Post On
British Post On
Canadian Post On
Intelligent Mail Bar Code On
Japanese Post On
KIX Post On
Planet Code On
Also see Planet Code
Check Digit, page 7-47.
Postal-4i On
7 - 44
Postnet On
Also see Postnet Check
Digit, page 7-47.
Postnet with B and B’ Fields On
InfoMail On
Combination 2D Postal Codes:
InfoMail and British
Post On
Intelligent Mail Bar Code and
Postnet with B and B’ Fields On
Postnet and
Postal-4i On
Postnet and
Intelligent Mail Bar Code On
Postal-4i and
Intelligent Mail Bar Code On
Postal-4i and
Postnet with B and B’ Fields On
Planet Code and
Postnet On
7 - 45
Planet Code and
Postnet with B and B’ Fields On
Planet Code and
Postal-4i On
Planet Code and
Intelligent Mail Bar Code On
Planet Code,
Postnet, and
Postal-4i On
Planet Code,
Postnet, and
Intelligent Mail Bar Code On
Planet Code,
Postal-4i, and
Intelligent Mail Bar Code On
Postnet,
Postal-4i, and
Intelligent Mail Bar Code On
Planet Code,
Postal-4i, and
Postnet with B and B’ Fields On
Planet Code,
Intelligent Mail Bar Code, and
Postnet with B and B’ Fields On
Postal-4i,
Intelligent Mail Bar Code, and
Postnet with B and B’ Fields On
7 - 46
Planet Code,
Postal-4i,
Intelligent Mail Bar Code, and
Postnet On
Planet Code,
Postal-4i,
Intelligent Mail Bar Code, and
Postnet with B and B’ Fields On
Planet Code Check Digit
This selection allows you to specify whether the check digit should be transmitted at the end of Planet Code data. Default
= Don’t Transmit.
Transmit Check Digit
* Don’t Transmit Check Digit
Postnet Check Digit
This selection allows you to specify whether the check digit should be transmitted at the end of Postnet data. Default =
Don’t Transmit.
Transmit Check Digit
* Don’t Transmit Check Digit
Australian Post Interpretation
This option controls what interpretation is applied to customer fields in Australian 4-State symbols.
Bar Output lists the bar patterns in “0123” format.
Numeric N Table causes that field to be interpreted as numeric data using the N Table.
Alphanumeric C Table causes the field to be interpreted as alphanumeric data using the C Table. Refer to the Australian
Post Specification Tables.
7 - 47
Combination C and N Tables causes the field to be interpreted using either the C or N Tables.
* Bar Output
Numeric N Table
Alphanumeric C Table
Combination C and N Tables
Postal Codes - Linear
The following lists linear postal codes. Any combination of linear postal code selections can be active at a time.
China Post (Hong Kong 2 of 5)
<Default All China Post (Hong Kong 2 of 5) Settings>
China Post (Hong Kong 2 of 5) On/Off
On
* Off
China Post (Hong Kong 2 of 5) Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 80.
Minimum Message Length
7 - 48
Maximum Message Length
Korea Post
<Default All Korea Post Settings>
Korea Post
On
* Off
Korea Post Message Length
Scan the bar codes below to change the message length. Refer to Message Length Description (page 7-2) for additional information. Minimum and Maximum lengths = 2-80. Minimum Default = 4, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
Korea Post Check Digit
This selection allows you to specify whether the check digit should be transmitted or not. Default = Don’t Transmit.
Transmit Check Digit
* Don’t Transmit Check Digit
7 - 49
7 - 50
8
Utilities
To Add a Test Code I.D. Prefix to All Symbologies
This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts,
beginning on page A-1) for the single character code that identifies each symbology.) This action first clears all current prefixes,
then programs a Code I.D. prefix for all symbologies. This is a temporary setting that will be removed when the unit is power
cycled.
Add Code I.D. Prefix to
All Symbologies (Temporary)
Show Decoder Revision
Scan the bar code below to output the decoder revision.
Show Decoder Revision
Show Scan Driver Revision
Scan the bar code below to output the scan driver revision.
Show Scan Driver Revision
Show Software Revision
Scan the bar code below to output the current software revision, unit serial number, and other product information.
Show Software Revision
Show Data Format
Scan the bar code below to show current data format settings.
DFMBK3?.
Data Format Settings
8-1
Test Menu
When you scan the Test Menu On code, then scan a programming code in this manual, the scanner displays the content of a
programming code. The programming function will still occur, but in addition, the content of that programming code is output to
the terminal.
Note: This feature should not be used during normal scanner operation.
On
* Off
TotalFreedom
TotalFreedom is an open system architecture that makes it possible for you create applications that reside on your scanner.
Decoding apps and Data Formatting apps can be created using TotalFreedom. For further information about TotalFreedom, go
to our website at www.honeywellaidc.com.
Application Plug-Ins (Apps)
Any apps that you are using can be turned off or on by scanning the following bar codes. Apps are stored in groups: Decoding,
and Formatting. You can enable and disable these groups of apps by scanning that group’s On or Off bar code below. You can
also scan the List Apps bar code to output a list of all your apps.
* Decoding Apps On
Decoding Apps Off
* Formatting Apps On
Formatting Apps Off
List Apps
Note: You must reset your device in order for the apps setting to take effect.
8-2
EZConfig-Scanning Introduction
EZConfig-Scanning provides a wide range of PC-based programming functions that can be performed on a scanner connected
to your PC. EZConfig-Scanning allows you to download upgrades to the scanner's firmware, change programmed parameters,
and create and print programming bar codes. Using EZConfig-Scanning, you can even save/open the programming parameters
for a scanner. This saved file can be e-mailed or, if required, you can create a single bar code that contains all the customized
programming parameters and mail or fax that bar code to any location. Users in other locations can scan the bar code to load in
the customized programming.
EZConfig-Scanning Operations
The EZConfig-Scanning software performs the following operations:
Scan Data
Scan Data allows you to scan bar codes and display the bar code data in a window. Scan Data lets you send serial
commands to the scanner and receive scanner response that can be seen in the Scan Data window. The data displayed in the Scan Data window can either be saved in a file or printed.
Configure
Configure displays the programming and configuration data of the scanner. The scanner's programming and configuration data is grouped into different categories. Each category is displayed as a tree item under the "Configure" tree
node in the application explorer. When one of these tree nodes is clicked, the right-hand side is loaded with the
parameters' form belonging to that particular category. The "Configure" tree option has all the programming and configuration parameters specified for a scanner. You can set or modify these parameters as required. You can later write
the modified settings to the scanner, or save them to a dcf file.
Installing EZConfig-Scanning from the Web
Note: EZConfig-Scanning requires .NET software. If .NET is not installed on your PC, you will be prompted to install it
during the EZConfig-Scanning installation.
1. Access the Honeywell web site at www.honeywellaidc.com
2. Click on the Products tab. Under Software, select Device Management.
3. Click on EZConfig-Device Configuration Software.
4. Click on the Software tab. Select EZConfig Cloud For Scanning (online version, must register for access) or
EZConfig for Scanning (to install on your PC, follow the next steps).
5. To install on your PC, when prompted, select Save File, and save the files to the c:\windows\temp directory.
6. Once you have finished downloading the file, exit the web site.
7. Using Explorer, go to the c:\windows\temp file.
8. Double click on the Setup.exe file. Follow the screen prompts to install the EZConfig-Scanning program.
9. If you’ve selected the defaults during installation, you can click on Start Menu-All Programs-Honeywell-EZConfigScanning and select EZConfig for your browser.
8-3
Resetting the Factory Defaults
This selection erases all your settings and resets the scanner to the original factory defaults. It also disables all plugins.
!
If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want to restore the scanner to factory default settings, first scan the Remove Custom Defaults bar code, then scan Activate Defaults. This resets the
scanner to the factory default settings.
Remove Custom Defaults
Activate Defaults
Note: Scanning the Activate Defaults bar code also causes both the scanner and the host to perform a reset and become
unlinked. You must relink (pair) the scanner to the host. See Wireless System Operation beginning on page 3-1 for
additional information.
The Menu Commands, beginning on page 9-4 list the factory default settings for each of the commands (indicated by an asterisk (*) on the programming pages).
8-4
9
Serial Programming Commands
The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the
programming bar codes will program the scanner. For complete descriptions and examples of each serial programming command, refer to the corresponding programming bar code in this manual.
The device must be set to an RS232 interface (see page 2-12). The following commands can be sent via a PC COM port using
terminal emulation software.
Conventions
The following conventions are used for menu and query command descriptions:
parameterA label representing the actual value you should send as part of a command.
[option] An optional part of a command.
{Data} Alternatives in a command.
bold
Names of menus, menu commands, buttons, dialog boxes, and windows that appear on the screen.
Menu Command Syntax
Menu commands have the following syntax (spaces have been used for clarity only):
Prefix [:Name:] Tag SubTag {Data} [, SubTag {Data}] [; Tag SubTag {Data}] […] Storage
Prefix Three ASCII characters: SYN M CR (ASCII 22,77,13).
:Name: This command is only used with wireless devices. It is used to specify whether you’re communicating with the host or
the scanner. To send information to the scanner, use :Voyager: The default factory setting for a scanner is Voyager.
This setting is changed by using the BT_NAM command, which accepts alphanumeric values. If the name is not known,
a wildcard (*) can be used :*:.
Tag
A 3 character case-insensitive field that identifies the desired menu command group. For example, all RS232
configuration settings are identified with a Tag of 232.
SubTag A 3 character case-insensitive field that identifies the desired menu command within the tag group. For example, the
SubTag for the RS232 baud rate is BAD.
Data
The new value for a menu setting, identified by the Tag and SubTag.
Storage A single character that specifies the storage table to which the command is applied. An exclamation point (!) performs
the command’s operation on the device’s volatile menu configuration table. A period (.) performs the command’s
operation on the device’s non-volatile menu configuration table. Use the non-volatile table only for semi-permanent
changes you want saved through a power cycle.
Query Commands
Several special characters can be used to query the device about its settings.
^
?
*
What is the default value for the setting(s).
What is the device’s current value for the setting(s).
What is the range of possible values for the setting(s). (The device’s response uses a dash (-) to indicate a
continuous range of values. A pipe (|) separates items in a list of non-continuous values.)
:Name: Field Usage (Optional)
This command returns the query information from the scanner.
Tag Field Usage
When a query is used in place of a Tag field, the query applies to the entire set of commands available for the particular
storage table indicated by the Storage field of the command. In this case, the SubTag and Data fields should not be used
because they are ignored by the device.
9-1
SubTag Field Usage
When a query is used in place of a SubTag field, the query applies only to the subset of commands available that match the
Tag field. In this case, the Data field should not be used because it is ignored by the device.
Data Field Usage
When a query is used in place of the Data field, the query applies only to the specific command identified by the Tag and
SubTag fields.
Concatenation of Multiple Commands
Multiple commands can be issued within one Prefix/Storage sequence. Only the Tag, SubTag, and Data fields must be
repeated for each command in the sequence. If additional commands are to be applied to the same Tag, then the new
command sequence is separated with a comma (,) and only the SubTag and Data fields of the additional command are
issued. If the additional command requires a different Tag field, the command is separated from previous commands by a
semicolon (;).
Responses
The device responds to serial commands with one of three responses:
ACK
ENQ
NAK
Indicates a good command which has been processed.
Indicates an invalid Tag or SubTag command.
Indicates the command was good, but the Data field entry was out of the allowable range for this Tag and SubTag
combination, e.g., an entry for a minimum message length of 100 when the field will only accept 2 characters.
When responding, the device echoes back the command sequence with the status character inserted directly before each
of the punctuation marks (the period, exclamation point, comma, or semicolon) in the command.
Examples of Query Commands
In the following examples, a bracketed notation [ ] depicts a non-displayable response.
Example: What is the range of possible values for Codabar Coding Enable?
Enter:
cbrena*.
Response: CBRENA0-1[ACK]
This response indicates that Codabar Coding Enable (CBRENA) has a range of values from 0 to 1 (off and on).
Example: What is the default value for Codabar Coding Enable?
Enter:
cbrena^.
Response: CBRENA1[ACK]
This response indicates that the default setting for Codabar Coding Enable (CBRENA) is 1, or on.
Example: What is the device’s current setting for Codabar Coding Enable?
Enter:
cbrena?.
Response: CBRENA1[ACK]
This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on.
Example: What are the device’s settings for all Codabar selections?
Enter:
cbr?.
Response: CBRENA1[ACK],
SSX0[ACK],
CK20[ACK],
CCT1[ACK],
MIN2[ACK],
MAX60[ACK],
DFT[ACK].
9-2
This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on;
the Start/Stop Character (SSX) is set to 0, or Don’t Transmit;
the Check Character (CK2) is set to 0, or Not Required;
concatenation (CCT) is set to 1, or Enabled;
the Minimum Message Length (MIN) is set to 2 characters;
the Maximum Message Length (MAX) is set to 60 characters;
and the Default setting (DFT) has no value.
Trigger Commands
You can activate and deactivate the scanner with serial trigger commands. First, the scanner must be put in Manual Trigger
Mode by scanning a Manual Trigger Mode bar code (page 4-8), or by sending a serial menu command for triggering (page 4-8).
Once the scanner is in serial trigger mode, the trigger is activated and deactivated by sending the following commands:
Activate:
SYN T CR
Deactivate: SYN U CR
The scanner scans until a bar code has been read, until the deactivate command is sent, or until the serial time-out has been
reached (see "Read Time-Out" on page 4-8 for a description, and the serial command on page 9-11).
Resetting the Custom Defaults
If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults bar code below. This
resets the scanner to the custom default settings. If there are no custom defaults, it will reset the scanner to the factory default
settings. Any settings that have not been specified through the custom defaults will be defaulted to the factory default settings.
Activate Custom Defaults
Note: The Custom Defaults settings apply to all workgroups Scanning the Activate Custom Defaults bar code also causes
both the scanner and the host to perform a reset and become unlinked. You must relink (pair) the scanner to the host.
See Wireless System Operation beginning on page 3-1 for additional information.
The charts on the following pages list the factory default settings for each of the commands (indicated by an asterisk (*) on the
programming pages).
9-3
Menu Commands
Selection
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Page
Product Default Settings
Pairing the Scanner with Bluetooth
Devices
Setting Custom Defaults
Resetting the Custom Defaults
Bluetooth HID Keyboard Connect
PAPBTH
1-3
Bluetooth HID Japanese Keyboard
Connect
PAPJKB
1-3
Pairing the Scanner with an Apple
Device Using SPP
PAPMFI
1-4
Set Custom Defaults
MNUCDP
1-6
Save Custom Defaults
MNUCDS
1-6
Activate Custom Defaults
DEFALT
1-6
*U.S.A.
KBDCTY0
2-1
Albania
KBDCTY35
2-1
Azeri (Cyrillic)
KBDCTY81
2-1
Azeri (Latin)
KBDCTY80
2-1
Belarus
KBDCTY82
2-1
Belgium
KBDCTY1
2-1
Bosnia
KBDCTY33
2-1
Brazil
KBDCTY16
2-1
Brazil (MS)
KBDCTY59
2-2
Bulgaria (Cyrillic)
KBDCTY52
2-2
Bulgaria (Latin)
KBDCTY53
2-2
Canada (French legacy)
KBDCTY54
2-2
Canada (French)
KBDCTY18
2-2
Canada (Multilingual)
KBDCTY55
2-2
Croatia
KBDCTY32
2-2
Czech
KBDCTY15
2-2
Czech (Programmers)
KBDCTY40
2-2
Czech (QWERTY)
KBDCTY39
2-2
Czech (QWERTZ)
KBDCTY38
2-2
Denmark
KBDCTY8
2-3
Dutch (Netherlands)
KBDCTY11
2-3
Estonia
KBDCTY41
2-3
Faroese
KBDCTY83
2-3
Finland
KBDCTY2
2-3
France
KBDCTY3
2-3
Gaelic
KBDCTY84
2-3
Germany
KBDCTY4
2-3
Greek
KBDCTY17
2-3
Greek (220 Latin)
KBDCTY64
2-3
Greek (220)
KBDCTY61
2-3
Programming the Interface
Program Keyboard
Country
9-4
Selection
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Greek (319 Latin)
KBDCTY65
2-4
Greek (319)
KBDCTY62
2-4
Greek (Latin)
KBDCTY63
2-4
Greek (MS)
KBDCTY66
2-4
Greek (Polytonic)
KBDCTY60
2-4
Hebrew
KBDCTY12
2-4
Hungarian (101 key)
KBDCTY50
2-4
Hungary
KBDCTY19
2-4
Iceland
KBDCTY75
2-4
Irish
KBDCTY73
2-4
Italian (142)
KBDCTY56
2-4
Italy
KBDCTY5
2-5
Japan ASCII
KBDCTY28
2-5
Kazakh
KBDCTY78
2-5
Kyrgyz (Cyrillic)
KBDCTY79
2-5
Latin America
KBDCTY14
2-5
Latvia
KBDCTY42
2-5
Latvia (QWERTY)
KBDCTY43
2-5
Lithuania
KBDCTY44
2-5
Lithuania (IBM)
KBDCTY45
2-5
Macedonia
KBDCTY34
2-5
Malta
KBDCTY74
2-5
Mongolian (Cyrillic)
KBDCTY86
2-6
Norway
KBDCTY9
2-6
Poland
KBDCTY20
2-6
Polish (214)
KBDCTY57
2-6
Polish (Programmers)
KBDCTY58
2-6
Portugal
KBDCTY13
2-6
Romania
KBDCTY25
2-6
Russia
KBDCTY26
2-6
Russian (MS)
KBDCTY67
2-6
Russian (Typewriter)
KBDCTY68
2-6
SCS
KBDCTY21
2-6
Serbia (Cyrillic)
KBDCTY37
2-7
Serbia (Latin)
KBDCTY36
2-7
Slovakia
KBDCTY22
2-7
Slovakia (QWERTY)
KBDCTY49
2-7
Slovakia (QWERTZ)
KBDCTY48
2-7
Slovenia
KBDCTY31
2-7
Spain
KBDCTY10
2-7
Spanish variation
KBDCTY51
2-7
Sweden
KBDCTY23
2-7
Switzerland (French)
KBDCTY29
2-7
Page
9-5
Selection
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Switzerland (German)
KBDCTY6
2-7
Tatar
KBDCTY85
2-8
Turkey F
KBDCTY27
2-8
Turkey Q
KBDCTY24
2-8
Ukrainian
KBDCTY76
2-8
United Kingdom
KBDCTY7
2-8
United Stated (Dvorak right)
KBDCTY89
2-8
United States (Dvorak left)
KBDCTY88
2-8
United States (Dvorak)
KBDCTY87
2-8
Page
United States (International)
KBDCTY30
2-8
Uzbek (Cyrillic)
KBDCTY77
2-8
*Regular
KBDSTY0
2-9
Caps Lock
KBDSTY1
2-9
Shift Lock
KBDSTY2
2-9
Automatic Caps Lock
KBDSTY6
2-9
Emulate External
Keyboard
KBDSTY5
2-9
*Keyboard Conversion Off
KBDCNV0
2-10
Convert all Characters to Upper
Case
KBDCNV1
2-10
Convert all Characters to Lower
Case
KBDCNV2
2-10
Control Character Output
*Control Character Output Off
KBDNPE0
2-10
*Control Character Output On
KBDNPE1
2-10
Keyboard Modifiers
*Control + X Off
KBDCAS0
2-11
DOS Mode Control + X
KBDCAS1
2-11
Windows Mode Control + X
KBDCAS2
2-10
Windows Mode Prefix/Suffix Off
KBDCAS3
2-11
*Turbo Mode Off
KBDTMD0
2-11
Turbo Mode On
KBDTMD1
2-11
*Numeric Keypad Off
KBDNPS0
2-11
Numeric Keypad On
KBDNPS1
2-11
*Auto Direct Connect Off
KBDADC0
2-11
Auto Direct Connect On
KBDADC1
2-11
Keyboard Wedge:
IBM PC AT and Compatibles with
CR suffix
PAP_AT
2-12
Laptop Direct Connect with CR
suffix
PAPLTD
2-12
RS232 Serial Port
PAP232
2-12
Keyboard Style
Keyboard Conversion
Programming an Interface for an Access Point
Plug and Play Codes
9-6
Selection
Plug and Play Codes:
RS485
Plug and Play Codes: IBM SurePos
Plug and Play Codes: USB
Remote MasterMind for USB
Plug and Play Codes
Baud Rate
Word Length: Data Bits, Stop Bits,
and Parity
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
IBM Port 5B Interface
PAPP5B
2-13
IBM Port 9B HHBCR-1 Interface
PAP9B1
2-13
IBM Port 17 Interface
PAPP17
2-13
IBM Port 9B HHBCR-2 Interface
PAP9B2
2-13
RS485 Packet Mode On
RTLPDF1
2-13
RS485 Packet Mode Off
RTLPDF0
2-13
Page
RS485 Packet Length (20-256)
RTLMPS
2-14
USB IBM SurePos Handheld
PAPSPH
2-14
USB IBM SurePos Tabletop
PAPSPT
2-14
USB Keyboard (PC)
PAP124
2-14
USB Keyboard (Mac)
PAP125
2-14
USB Japanese Keyboard (PC)
TRMUSB134
2-14
USB HID
PAP131
2-15
USB Serial
TRMUSB130
2-15
CTS/RTS Emulation On
USBCTS1
2-15
CTS/RTS Emulation Off*
USBCTS0
2-15
ACK/NAK Mode On
USBACK1
2-15
ACK/NAK Mode Off*
USBACK0
2-15
ReM Off
REMIFC0
2-15
ReM On
REMIFC1
2-15
Gilbarco Terminal
PAPGLB
2-16
Honeywell Bioptic Aux Port
PAPBIO
2-16
Datalogic Magellan Aux Port
PAPMAG
2-16
NCR Bioptic Aux Port
PAPNCR
2-17
Wincor Nixdorf Terminal
PAPWNX
2-17
Wincor Nixdorf Beetle
PAPBTL
2-17
Wincor Nixdorf RS232 Mode A
PAPWMA
2-18
300 BPS
232BAD0
2-18
600 BPS
232BAD1
2-18
1200 BPS
232BAD2
2-18
2400 BPS
232BAD3
2-18
4800 BPS
232BAD4
2-18
9600 BPS
232BAD5
2-19
19200 BPS
232BAD6
2-18
38400 BPS
232BAD7
2-19
57600 BPS
232BAD8
2-19
*115200 BPS
232BAD9
2-19
7 Data, 1 Stop, Parity Even
232WRD3
2-19
7 Data, 1 Stop, Parity None
232WRD0
2-19
7 Data, 1 Stop, Parity Odd
232WRD6
2-19
7 Data, 2 Stop, Parity Even
232WRD4
2-19
7 Data, 2 Stop, Parity None
232WRD1
2-19
9-7
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
7 Data, 2 Stop, Parity Odd
232WRD7
2-19
8 Data, 1 Stop, Parity Even
232WRD5
2-19
*8 Data, 1 Stop, Parity None
232WRD2
2-20
8 Data, 1 Stop, Parity Odd
232WRD8
2-20
8 Data, 1 Stop, Parity Mark
232WRD14
2-20
RS232 Receiver Time-out
Range 0 - 300 seconds
232LPT###
2-20
RS232 Handshaking
*RTS/CTS Off
232CTS0
2-21
Flow Control, No Timeout
232CTS1
2-20
Two-Direction Flow Control
232CTS2
2-20
Selection
Scanner-Bioptic Packet Mode
Page
Flow Control with Timeout
232CTS3
2-20
RS232 Timeout
232DEL####
2-21
*XON/XOFF Off
232XON0
2-21
XON/XOFF On
232XON1
2-21
*ACK/NAK Off
232ACK0
2-21
ACK/NAK On
232ACK1
2-21
*Packet Mode Off
232PKT0
2-22
Packet Mode On
232PKT2
2-13
Scanner-Bioptic ACK/NAK Mode
*Bioptic ACK/NAK Off
232NAK0
2-22
Bioptic ACK/NAK On
232NAK1
2-22
Scanner-Bioptic ACK/NAK Timeout
ACK/NAK Timeout
*5100
232DLK#####
2-22
USB Communication (Corded
Scanner)
BTUENA1.
2-23
Bluetooth Communication
(Cordless Scanner)
BTUENA0.
2-23
Corded USB PC or Macintosh
Keyboard
Corded USB Keyboard (PC)
BTUMID124.
2-23
Corded USB Keyboard (Mac)
BTUMID125.
2-23
2-23
Programming the VG1602 Corded Interface
Setting the VG1602 Corded
Interface
Corded USB HID POS
Corded USB HID POS Interface
BTUMID131.
Corded USB Serial
Corded USB Serial
BTUMID130.
2-24
Corded CTS/RTS Emulation
Corded CTS/RTS Emulation On
BTUCTS1.
2-24
*Corded CTS/RTS Emulation Off
BTUCTS0.
2-24
Corded ACK/NAK Mode On
BTUACK1.
2-24
*Corded ACK/NAK Mode Off
BTUACK0.
2-24
Bluetooth HID Keyboard
Disconnect
PAPSPP
3-1
Bluetooth Serial Port - PCs/
Laptops
BT_TRM0;BT_DNG5
3-1
BT Connection - PDA/Mobility
Systems Device
BT_TRM0;BT_DNG1
3-1
Bluetooth PIN Code
Bluetooth PIN
BT_PIN
3-1
Auto Reconnect Mode
*Auto Reconnect On
BT_ACM1
3-2
Auto Reconnect Off
BT_ACM0
3-2
Corded ACK/NAK Mode
Wireless System Operation
Bluetooth Connection
9-8
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Maximum Link Attempts
Maximum Link Attempts
BT_MLA
3-3
Relink Time-Out
Relink Time-Out
BT_RLT
3-3
Reset Scanner
Reset Scanner
RESET_
3-6
Selection
Page
Scanner Report
Scanner Report
RPTSCN
3-6
Scanner Address
Scanner Address
BT_LDA
3-7
Linked Modes
Locked Link Mode
BASCON0,DNG1
3-7
*Open Link Mode
BASCON1,DNG1
3-7
Unlink Scanner
BT_RMV
3-7
Override Locked Scanner
BT_RPL1
3-8
Out-of-Range Alarm
Scanner Alarm Duration (Range 1
- 3000 sec (*0))
BT_ORD
3-8
Alarm Sound Type
Scanner Alarm Type
BT_ORW
3-8
Scanner Idle Alarm
Scanner Idle Alarm On
BT_LOS1
3-9
*Scanner Idle Alarm Off
BT_LOS0
3-9
Timer (0-7200 seconds)
BT_LPT0
3-9
200 Seconds
BT_LPT200
3-9
400 Seconds
BT_LPT400
3-9
900 Seconds
BT_LPT900
3-9
3600 Seconds
BT_LPT3600
3-9
7200 Seconds
BT_LPT7200
3-9
*Full Power
BT_TXP100
3-10
Medium Power
BT_TXP35
3-10
Medium Low Power
BT_TXP5
3-10
Low Power
BT_TXP1
3-10
Multiple Scanner
Operation
Multiple Scanner Operation
BASCON2,DNG3
3-10
Scanner Name
Name 1-7
BT_NAM#####
3-11
Reset
RESET_
3-11
Scanner Name
BT_NAM
3-11
Application Work Group
Selections
*Group 0
GRPSEL0
3-12
Group 1-6
GRPSEL#
3-12
Resetting the Factory Defaults: All
Application Work Groups
Factory Default Settings:
All Work Groups
PAPDFT&
3-13
Resetting the Custom Defaults: All
Application Work Groups
Custom Default Settings:
All Work Groups
PAPDFT
3-13
Disconnect from Host and Connect
to an Access Point
Bluetooth HID Keyboard
Disconnect
PAPSPP
3-14
Replacing a Linked Scanner
Override Locked Scanner
BT_RPL1
3-14
Access Point Address
Base Address
:*:BASLDA
3-15
Paging Mode
*On
BEPPGE1
3-15
Off
BEPPGE0
3-15
Range 400 - 9000 Hz (*1000)
BEPPFQ####
3-15
Scanner Power Time-Out Timer
Flexible Power Management
Paging Pitch
9-9
Selection
Batch Mode
Batch Mode Beep
Batch Mode Storage
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Automatic Batch Mode
BATENA1
3-16
*Batch Mode Off
BATENA0
3-16
Inventory Batch Mode
BATENA2
3-16
Persistent Batch Mode
BATENA3
3-16
Off
BATBEP0
3-17
*On
BATBEP1
3-17
Page
*Flash Storage
BATNVS1
3-17
RAM Storage
BATNVS0
3-17
Batch Mode Quantity
*Off
BATQTY0
3-17
On
BATQTY1
3-17
Quantity Codes
0
BATNUM0
3-18
*1
BATNUM1
3-18
2
BATNUM2
3-18
3
BATNUM3
3-18
4
BATNUM4
3-19
5
BATNUM5
3-19
6
BATNUM6
3-19
7
BATNUM7
3-19
8
BATNUM8
3-19
9
BATNUM9
3-19
Batch Mode Output Order
*FIFO
BATLIF0
3-19
LIFO
BATLIF1
3-19
Total Records
Total Records
BATNRC
3-19
Delete Last Code
Delete Last Code
BATUND
3-20
Clear All Codes
Clear All Codes
BATCLR
3-20
Transmit Records to Host
Transmit Inventory Records
BAT_TX
3-20
Batch Mode Transmit Delay
*Off
BATDLY0
3-20
Short (ms)
BATDLY250
3-20
Medium (ms)
BATDLY500
3-20
Long (ms)
BATDLY1000
3-20
Host Command Acknowledgment
Host ACK On
HSTACK1
3-22
*Host ACK Off
HSTACK0
3-22
Host ACK Timeout
HSTATO
3-22
Input/Output Selections
Programmable Button
9 - 10
Virtual Keyboard On - Short Press
BTNSEC1
4-1
Virtual Keyboard On - Long Press
BTNSCL1
4-1
Battery Charge Status On - Short
Press
BTNSEC2
4-2
Battery Charge Status On - Long
Press
BTNSCL2
4-2
Flashlight Mode On - Short Press
BTNSEC3
4-2
Flashlight Mode On - Long Press
BTNSCL3
4-2
Selection
Power Up Beeper
Beep on BEL Character
Trigger Click
Beeper - Good Read
Beeper Volume - Good Read
Beeper Pitch - Good Read
(Frequency)
Beeper Pitch - Error (Frequency)
Beeper Duration - Good Read
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Bluetooth Pair/Unpair On - Short
Press
BTNSEC4
4-3
Bluetooth Pair/Unpair On - Long
Press
BTNSCL4
4-3
*Disable Short Press
BTNSEC0
4-3
*Disable Long Press
BTNSCL0
4-3
Page
Power Up Beeper Off
BEPPWR0
4-4
*Power Up Beeper On
BEPPWR1
4-4
Beep on BEL On
BELBEP1
4-4
*Beep on BEL Off
BELBEP0
4-4
On
BEPTRG1
4-4
*Off
BEPTRG0
4-4
Off
BEPBEP0
4-5
*On
BEPBEP1
4-5
Off
BEPLVL0
4-5
Low
BEPLVL1
4-5
Medium
BEPLVL2
4-5
*High
BEPLVL3
4-5
Low (1600) (min 400Hz)
BEPFQ11600
4-5
*Medium (2700 Hz)
BEPFQ12700
4-5
High (4200) (max 9000Hz)
BEPFQ14200
4-5
*Razz (250) (min 200Hz)
BEPFQ2800
4-6
Medium (3250)
BEPFQ23250
4-6
High (4200) (max 9000Hz)
BEPFQ24200
4-6
*Normal Beep
BEPBIP0
4-6
Short Beep
BEPBIP1
4-6
Off
BEPLED0
4-6
*On
BEPLED1
4-6
*1
BEPERR3
4-7
Range 1 - 9
BEPERR#
4-7
*1
BEPRPT1
4-7
Range 1 - 9
BEPRPT#
4-7
*No Delay
DLYGRD0
4-7
Short Delay (500 ms)
DLYGRD500
4-7
Medium Delay (1000 ms)
DLYGRD1000
4-7
Long Delay (1500 ms)
DLYGRD1500
4-7
User-Specified Good Read Delay
Range 0 - 30,000 ms
DLYGRD#####
4-7
Manual Trigger Modes
*Manual Trigger - Normal
PAPHHF
4-8
Manual Trigger - Enhanced
PAPHHS
4-8
Read Time-Out
(0 - 300,000 ms) *30,000
TRGSTO####
4-8
LED - Good Read
Number of Beeps - Error
Number of Beeps - Good Read
Good Read Delay
Serial Trigger Mode
9 - 11
Selection
Poor Quality Codes
CodeGate
Mobile Phone Read Mode
Character Activation Mode
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Poor Quality 1D Reading On
DECLDI1
4-8
*Poor Quality 1D Reading Off
DECLDI0
4-8
Poor Quality PDF Reading On
PDFXPR1
4-9
*Poor Quality PDF Reading Off
PDFXPR0
4-9
*CodeGate Off Out-of-Stand
AOSCGD0.
4-9
CodeGate On Out-of-Stand
AOSCGD1.
4-9
Hand Held Scanning - Mobile
Phone
PAPHHC
4-9
Page
*Off
HSTCEN0
4-10
On
HSTCEN1
4-10
Activation Character (Range 0255) *12 [DC2]
HSTACH###
4-10
*Do Not End Character Activation
After Good Read
HSTCGD0
4-10
End Character Activation After
Good Read
HSTCGD1
4-10
Character Activation Timeout
(Range 1 - 300,000) *30,000 ms
HSTCDT######
4-11
*Off
HSTDEN0
4-11
On
HSTDEN1
4-11
Deactivation Character (Range 0255) *14 [DC4]
HSTDCH###
4-11
*Lights On
SCNLED1
4-11
Lights Off
SCNLED0
4-11
200 milliseconds
SCNDLY200
4-12
400 milliseconds
SCNDLY400
4-12
*Off (no delay)
SCNDLY0
4-12
User-Specified Aimer Delay
Range 0 - 4,000 ms
SCNDLY####
4-12
Aimer Mode
Off
SCNAIM0.
4-12
*Interlaced
SCNAIM2.
4-12
Centering On
DECWIN1
4-13
*Centering Off
DECWIN0
4-13
Left of Centering Window (*40%)
DECLFT###
4-13
Right of Centering Window (*60%)
DECRGT###
4-14
Top of Centering Window (*40%)
DECTOP###
4-13
Bottom of Centering Window
(*60%)
DECBOT###
4-13
On
PRFENA1
4-14
*Off
PRFENA0
4-14
High Priority Symbology
PRFCOD##
4-14
Low Priority Symbology
PRFBLK##
4-15
Preferred Symbology Timeout
(*500) Range 100-3000
PRFPTO####
4-15
Preferred Symbology Default
PRFDFT
4-15
Character Deactivation Mode
Illumination Lights
Aimer Delay
Centering Window
Preferred Symbology
9 - 12
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Output Sequence Editor
Enter Sequence
SEQBLK
4-17
Default Sequence
SEQDFT
4-17
Partial Sequence
Transmit Partial Sequence
SEQTTS1
4-17
*Discard Partial Sequence
SEQTTS0
4-17
Required
SEQ_EN2
4-18
On/Not Required
SEQ_EN1
4-18
Selection
Require Output Sequence
Multiple Symbols
No Read
Video Reverse
Page
*Off
SEQ_EN0
4-18
On
SHOTGN1
4-18
*Off
SHOTGN0
4-18
On
SHWNRD1
4-18
*Off
SHWNRD0
4-18
Video Reverse Only
VIDREV1
4-19
Video Reverse and Standard Bar
Codes
VIDREV2
4-19
*Video Reverse Off
VIDREV0
4-19
*Upright
ROTATN0
4-20
Vertical, Bottom to Top (Rotate
CCW 90°)
ROTATN1
4-20
Upside Down
ROTATN2
4-20
Vertical, Top to Bottom (Rotate CW
90°)
ROTATN3
4-20
VSUFCR
5-2
Add Prefix
PREBK2##
5-2
Clear One Prefix
PRECL2
5-2
Clear All Prefixes
PRECA2
5-2
Add Suffix
SUFBK2##
5-2
Clear One Suffix
SUFCL2
5-2
Clear All Suffixes
SUFCA2
5-2
*Enable
RMVFNC0
5-3
Disable
RMVFNC1
5-3
Intercharacter Delay
Range 0 - 1000 (5ms increments)
DLYCHR##
5-3
User Specified
Intercharacter Delay
Delay Length
0 - 1000 (5ms increments)
DLYCRX##
5-4
Character to Trigger Delay
DLY_XX##
5-4
Interfunction Delay
Range 0 - 1000 (5ms increments)
DLYFNC##
5-4
Intermessage Delay
Range 0 - 1000 (5ms increments)
DLYMSG##
5-4
Working Orientation
Prefix/Suffix Selections
Add CR Suffix to All Symbologies
Prefix
Suffix
Function Code Transmit
Data Formatter Selections
Data Format Editor
*Default Data Format (None)
DFMDF3
6-1
Enter Data Format
DFMBK3##
6-2
Clear One Data Format
DFMCL3
6-2
Clear All Data Formats
DFMCA3
6-2
9 - 13
Selection
Data Formatter
Data Format Non-Match Error Tone
Primary/Alternate Data Formats
Single Scan Data Format Change
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Data Formatter Off
DFM_EN0
6-9
*Data Formatter On,
Not Required,
Keep Prefix/Suffix
DFM_EN1
6-9
Data Format Required,
Keep Prefix/Suffix
DFM_EN2
6-9
Data Formatter On,
Not Required,
Drop Prefix/Suffix
DFM_EN3
6-9
Data Format Required,
Drop Prefix/Suffix
DFM_EN4
6-9
*Data Format Non-Match Error
Tone On
DFMDEC0
6-10
Data Format Non-Match Error
Tone Off
DFMDEC1
6-10
Page
Primary Data Format
ALTFNM0
6-10
Data Format 1
ALTFNM1
6-10
Data Format 2
ALTFNM2
6-10
Data Format 3
ALTFNM3
6-10
Single Scan-Primary
Data Format
VSAF_0
6-11
Single Scan-Data Format 1
VSAF_1
6-11
Single Scan-Data Format 2
VSAF_2
6-11
Single Scan-Data Format 3
VSAF_3
6-11
7-1
Symbologies
All Symbologies
Codabar
Codabar Start/Stop Char.
Codabar Check Char.
Codabar Concatenation
Codabar Message Length
Code 39
9 - 14
*All Symbologies Off
ALLENA0
All Symbologies On
ALLENA1
7-1
Default All Codabar
Settings
CBRDFT
7-2
Off
CBRENA0
7-2
*On
CBRENA1
7-2
*Don’t Transmit
CBRSSX0
7-2
Transmit
CBRSSX1
7-2
*No Check Char.
CBRCK20
7-2
Validate, But Don’t Transmit
CBRCK21
7-2
Validate, and Transmit
CBRCK22
7-2
*Off
CBRCCT0
7-3
On
CBRCCT1
7-3
Require
CBRCCT2
7-3
Minimum (2 - 60) *4
CBRMIN##
7-3
Maximum (2 - 60) *60
CBRMAX##
7-3
Default All Code 39
Settings
C39DFT
7-4
Off
C39ENA0
7-4
*On
C39ENA1
7-4
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Code 39 Start/Stop Char.
*Don’t Transmit
C39SSX0
Transmit
C39SSX1
7-4
Code 39 Check Char.
*No Check Char.
C39CK20
7-4
Validate, But Don’t
Transmit
C39CK21
7-4
Validate,
and Transmit
C39CK22
7-4
Minimum (0 - 48) *0
C39MIN##
7-5
Maximum (0 - 48) *48
C39MAX##
7-5
*Off
C39APP0
7-5
On
C39APP1
7-5
Code 32 Pharmaceutical (PARAF)
*Off
C39B320
7-5
On
C39B321
7-5
Code 39 Full ASCII
*Off
C39ASC0
7-6
On
C39ASC1
7-6
Code 39 Code Page
C39DCP
7-6
Default All Interleaved
2 of 5 Settings
I25DFT
7-7
Off
I25ENA0
7-7
Selection
Code 39 Message Length
Code 39 Append
Interleaved 2 of 5
Interleaved 2 of 5 Check Digit
Interleaved 2 of 5 Message Length
NEC 2 of 5
NEC 2 of 5 Check Digit
NEC 2 of 5 Message Length
Code 93
Page
7-4
*On
I25ENA1
7-7
*No Check Char.
I25CK20
7-7
Validate, But Don’t
Transmit
I25CK21
7-7
Validate, and Transmit
I25CK22
7-7
Minimum (2 - 80) *4
I25MIN##
7-7
Maximum (2 - 80) *80
I25MAX##
7-7
Default All NEC
2 of 5 Settings
N25DFT
7-8
Off
N25ENA0
7-8
*On
N25ENA1
7-8
*No Check Char.
N25CK20
7-8
Validate, But Don’t
Transmit
N25CK21
7-8
Validate, and Transmit
N25CK22
7-8
Minimum (2 - 80) *4
N25MIN##
7-9
Maximum (2 - 80) *80
N25MAX##
7-9
Default All Code 93
Settings
C93DFT
7-9
Off
C93ENA0
7-9
*On
C93ENA1
7-9
Code 93 Message Length
Minimum (0 - 80) *0
C93MIN##
7-9
Maximum (0 - 80) *80
C93MAX##
7-9
Code 93 Append
On
C93APP1
7-10
*Off
C93APP0
7-10
9 - 15
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Code 93 Code Page
Code 93 Code Page
C93DCP
7-10
Straight 2 of 5 Industrial
Default All Straight 2 of 5 Industrial
Settings
R25DFT
7-11
*Off
R25ENA0
7-11
Selection
Page
On
R25ENA1
7-11
Straight 2 of 5 Industrial Message
Length
Minimum (1 - 48) *4
R25MIN##
7-11
Maximum (1 - 48) *48
R25MAX##
7-11
Straight 2 of 5 IATA
Default All Straight 2 of 5 IATA
Settings
A25DFT
7-12
Straight 2 of 5 IATA
Straight 2 of 5 IATA Message Length
Matrix 2 of 5
Matrix 2 of 5 Message Length
Code 11
Code 11 Check Digits Required
Code 11 Message Length
Code 128
*Off
A25ENA0
7-12
On
A25ENA1
7-12
Minimum (1 - 48) *4
A25MIN##
7-12
Maximum (1 - 48) *48
A25MAX##
7-12
Default All Matrix 2 of 5
Settings
X25DFT
7-13
*Off
X25ENA0
7-13
On
X25ENA1
7-13
Minimum (1 - 80) *4
X25MIN##
7-13
Maximum (1 - 80) *80
X25MAX##
7-13
Default All Code 11
Settings
C11DFT
7-14
*Off
C11ENA0
7-14
On
C11ENA1
7-14
1 Check Digit
C11CK20
7-14
*2 Check Digits
C11CK21
7-14
Minimum (1 - 80) *4
C11MIN##
7-14
Maximum (1 - 80) *80
C11MAX##
7-14
Default All Code 128
Settings
128DFT
7-15
Off
128ENA0
7-15
*On
128ENA1
7-15
ISBT Concatenation
*Off
ISBENA0
7-15
On
ISBENA1
7-15
Code 128 Message Length
Minimum (0 - 80) *0
128MIN##
7-15
Maximum (0 - 80) *80
128MAX##
7-15
Code 128 Append
*On
128APP1
7-16
Off
128APP0
7-16
Code 128 Code Page
Code 128 Code Page (*2)
128DCP##
7-16
Default All GS1-128 Settings
GS1DFT
7-17
*On
GS1ENA1
7-17
Off
GS1ENA0
7-17
Minimum (1 - 80) *1
GS1MIN##
7-17
Maximum (0 - 80) *80
GS1MAX##
7-17
GS1-128
GS1-128 Message Length
9 - 16
Selection
Telepen
Telepen Output
Telepen Message Length
UPC-A
UPC-A Check Digit
UPC-A Number System
UPC-A 2 Digit Addenda
UPC-A 5 Digit Addenda
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Default All Telepen
Settings
TELDFT
7-18
*Off
TELENA0
7-18
On
TELENA1
7-18
*AIM Telepen Output
TELOLD0
7-18
Original Telepen Output
TELOLD1
7-18
Page
Minimum (1 - 60) *1
TELMIN##
7-18
Maximum (1 - 60) *60
TELMAX##
7-18
Default All
UPC-A Settings
UPADFT
7-19
Off
UPBENA0
7-19
*On
UPBENA1
7-19
Off
UPACKX0
7-19
*On
UPACKX1
7-19
Off
UPANSX0
7-19
*On
UPANSX1
7-19
*Off
UPAAD20
7-20
On
UPAAD21
7-20
*Off
UPAAD50
7-20
On
UPAAD51
7-20
UPC-A Addenda Required
*Not Required
UPAARQ0
7-20
Required
UPAARQ1
7-20
UPC-A Addenda
Separator
Off
UPAADS0
7-20
*On
UPAADS1
7-20
UPC-A/EAN-13 with Extended
Coupon Code
*Off
CPNENA0
7-21
Allow Concatenation
CPNENA1
7-21
Require Concatenation
CPNENA2
7-21
GS1 Output Off
CPNGS10
7-21
GS1 Output On
CPNGS11
7-21
Default All UPC-E
Settings
UPEDFT
7-22
Off
UPEEN00
7-22
*On
UPEEN01
7-22
Coupon GS1 DataBar Output
UPC-E0
UPC-E0 Expand
UPC-E0 Addenda Required
UPC-E0 Addenda Separator
UPC-E0 Check Digit
UPC-E0 Leading Zero
*Off
UPEEXP0
7-22
On
UPEEXP1
7-22
Required
UPEARQ1
7-22
*Not Required
UPEARQ0
7-22
*On
UPEADS1
7-23
Off
UPEADS0
7-23
Off
UPECKX0
7-23
*On
UPECKX1
7-23
Off
UPENSX0
7-23
*On
UPENSX1
7-23
9 - 17
Selection
UPC-E0 Addenda
UPC-E1
EAN/JAN-13
Convert UPC-A to EAN-13
EAN/JAN-13 Check Digit
EAN/JAN-13 2 Digit Addenda
EAN/JAN-13 Addenda Required
EAN/JAN-13 Addenda
Separator
ISBN Translate
EAN/JAN-8
EAN/JAN-8 Check Digit
EAN/JAN-8 Addenda
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
2 Digit Addenda On
UPEAD21
7-23
*2 Digit Addenda Off
UPEAD20
7-23
5 Digit Addenda On
UPEAD51
7-23
Page
*5 Digit Addenda Off
UPEAD50
7-23
*Off
UPEEN10
7-24
On
UPEEN11
7-24
Default All EAN/
JAN Settings
E13DFT
7-24
Off
E13ENA0
7-24
*On
E13ENA1
7-24
UPC-A Converted to EAN-13
UPAENA0
7-24
Do not Convert UPC-A
UPAENA1
7-24
Off
E13CKX0
7-25
*On
E13CKX1
7-25
2 Digit Addenda On
E13AD21
7-25
*2 Digit Addenda Off
E13AD20
7-25
5 Digit Addenda On
E13AD51
7-25
*5 Digit Addenda Off
E13AD50
7-25
*Not Required
E13ARQ0
7-25
Required
E13ARQ1
7-25
Off
E13ADS0
7-26
*On
E13ADS1
7-26
*Off
E13ISB0
7-26
On
E13ISB1
7-26
Default All EAN/
JAN 8 Settings
EA8DFT
7-27
Off
EA8ENA0
7-27
*On
EA8ENA1
7-27
Off
EA8CKX0
7-27
*On
EA8CKX1
7-27
*2 Digit Addenda Off
EA8AD20
7-27
2 Digit Addenda On
EA8AD21
7-27
*5 Digit Addenda Off
EA8AD50
7-27
5 Digit Addenda On
EA8AD51
7-27
*Not Required
EA8ARQ0
7-28
Required
EA8ARQ1
7-28
EAN/JAN-8 Addenda
Separator
Off
EA8ADS0
7-28
*On
EA8ADS1
7-28
MSI
Default All MSI Settings
MSIDFT
7-29
*Off
MSIENA0
7-29
On
MSIENA1
7-29
EAN/JAN-8 Addenda Required
9 - 18
Selection
MSI Check Character
MSI Message Length
GS1 DataBar Omnidirectional
GS1 DataBar Limited
GS1 DataBar Expanded
GS1 DataBar Expanded Msg.
Length
Trioptic Code
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
*Validate Type 10, but Don’t
Transmit
MSICHK0
7-29
Validate Type 10 and
Transmit
MSICHK1
7-29
Validate 2 Type 10 Chars, but Don’t
Transmit
MSICHK2
7-29
Validate 2 Type 10 Chars and
Transmit
MSICHK3
7-29
Validate Type 11 then Type 10
Char, but Don’t Transmit
MSICHK4
7-29
Validate Type 11 then Type 10
Char and Transmit
MSICHK5
7-30
Disable MSI Check Characters
MSICHK6
7-30
Minimum (4 - 48) *4
MSIMIN##
7-30
Maximum (4 - 48) *48
MSIMAX##
7-30
Default All
GS1 DataBar Omnidirectional
Settings
RSSDFT
7-31
Off
RSSENA0
7-31
*On
RSSENA1
7-31
Default All GS1 DataBar Limited
Settings
RSLDFT
7-31
Off
RSLENA0
7-31
*On
RSLENA1
7-31
Default All GS1 DataBar
Expanded Settings
RSEDFT
7-32
Off
RSEENA0
7-32
Page
*On
RSEENA1
7-32
Minimum (4 - 74) *4
RSEMIN##
7-32
Maximum (4 - 74) *74
RSEMAX##
7-32
*Off
TRIENA0
7-32
On
TRIENA1
7-32
Default All Codablock A Settings
CBADFT
7-33
*Off
CBAENA0
7-33
On
CBAENA1
7-33
Codablock A Msg. Length
Minimum (1 - 600) *1
CBAMIN###
7-33
Maximum (1 - 600) *600
CBAMAX###
7-33
Codablock F
Default All Codablock F Settings
CBFDFT
7-34
*Off
CBFENA0
7-34
On
CBFENA1
7-34
Minimum (1 - 2048) *1
CBFMIN####
7-34
Maximum (1 - 2048) *2048
CBFMAX####
7-34
On
LBLENA1
7-34
* Off
LBLENA0
7-34
Codablock A
Codablock F Msg. Length
Label Code
9 - 19
Selection
PDF417
PDF417 Msg. Length
MacroPDF417
MicroPDF417
MicroPDF417 Msg. Length
GS1 Composite Codes
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Default All PDF417 Settings
PDFDFT
7-35
*On
PDFENA1
7-35
Off
PDFENA0
7-35
Page
Minimum (1-2750) *1
PDFMIN####
7-35
Maximum (1-2750) *2750
PDFMAX####
7-35
*On
PDFMAC1
7-36
Off
PDFMAC0
7-36
Default All Micro PDF417 Settings
MPDDFT
7-36
On
MPDENA1
7-36
*Off
MPDENA0
7-36
Minimum (1-366) *1
MPDMIN###
7-36
Maximum (1-366) *366
MPDMAX###
7-36
On
COMENA1
7-36
*Off
COMENA0
7-36
UPC/EAN Version
On
COMUPC1
7-37
*Off
COMUPC0
7-37
GS1 Composite Codes Msg. Length
Minimum (1-2435) *1
COMMIN####
7-37
Maximum (1-2435) *2435
COMMAX####
7-37
GS1 Emulation
GS1-128 Emulation
EANEMU1
7-37
GS1 DataBar Emulation
EANEMU2
7-36
GS1 Code Expansion Off
EANEMU3
7-38
EAN8 to EAN13 Conversion
EANEMU4
7-38
*GS1 Emulation Off
EANEMU0
7-38
On
T39ENA1
7-38
*Off
T39ENA0
7-38
Default All QR Code Settings
QRCDFT
7-38
*On
QRCENA1
7-38
Off
QRCENA0
7-38
Minimum (1-7089) *1
QRCMIN####
7-39
Maximum (1-7089) *7089
QRCMAX####
7-39
*On
QRCAPP1
7-39
Off
QRCAPP0
7-39
QR Code Page
QR Code Page (*3)
QRCDCP##
7-39
Data Matrix
Default All Data Matrix Settings
IDMDFT
7-40
*On
IDMENA1
7-40
Off
IDMENA0
7-40
Minimum (1-3116) *1
IDMMIN####
7-40
Maximum (1-3116) *3116
IDMMAX####
7-40
TCIF Linked Code 39
QR Code
QR Code Msg. Length
QR Code Append
Data Matrix Msg. Length
Data Matrix Append
Data Matrix Code Page
9 - 20
*On
IDMAPP1
7-40
Off
IDMAPP0
7-40
Data Matrix Code Page (*51)
IDMDCP##
7-40
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Default All MaxiCode Settings
MAXDFT
7-41
On
MAXENA1
7-41
*Off
MAXENA0
7-41
Minimum (1-150) *1
MAXMIN###
7-41
Maximum (1-150) *150
MAXMAX###
7-41
Default All Aztec Code Settings
AZTDFT
7-42
*On
AZTENA1
7-42
Off
AZTENA0
7-42
Aztec Code Msg. Length
Minimum (1-3832) *1
AZTMIN####
7-42
Maximum (1-3832) *3832
AZTMAX####
7-42
Aztec Append
*On
AZTAPP1
7-42
Off
AZTAPP0
7-42
Aztec Code Page
Aztec Code Page (*51)
AZTDCP##
7-42
Chinese Sensible (Han Xin) Code
Default All Han Xin Code Settings
HX_DFT
7-43
On
HX_ENA1
7-43
Selection
MaxiCode
MaxiCode Msg. Length
Aztec Code
Chinese Sensible (Han Xin) Code
Msg. Length
Page
*Off
HX_ENA0
7-43
Minimum (1-7833) *1
HX_MIN####
7-43
Maximum (1-7833) *7833
HX_MAX####
7-43
*Off
POSTAL0
7-44
Postal Codes - 2D
2D Postal Codes
Single 2D Postal Codes
Australian Post On
POSTAL1
7-44
British Post On
POSTAL7
7-44
Canadian Post On
POSTAL30
7-44
Intelligent Mail Bar Code On
POSTAL10
7-44
Japanese Post On
POSTAL3
7-44
KIX Post On
POSTAL4
7-44
Planet Code On
POSTAL5
7-44
Postal-4i On
POSTAL9
7-44
Postnet On
POSTAL6
7-45
Postnet with B and B’ Fields On
POSTAL11
7-45
InfoMail On
POSTAL2
7-45
9 - 21
Selection
Combination 2D Postal Codes
Combination 2D Postal Codes
(continued)
Planet Code Check Digit
Postnet Check Digit
Australian Post Interpretation
9 - 22
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
InfoMail and British Post On
POSTAL8
7-45
Intelligent Mail Bar Code and
Postnet with B and B’ Fields On
POSTAL20
7-45
Postnet and Postal-4i On
POSTAL14
7-45
Postnet and Intelligent Mail Bar
Code On
POSTAL16
7-45
Postal-4i and Intelligent Mail Bar
Code On
POSTAL17
7-45
Postal-4i and Postnet with B and B’
Fields On
POSTAL19
7-45
Planet and Postnet On
POSTAL12
7-45
Planet and Postnet with B and B’
Fields On
POSTAL18
7-46
Planet and Postal-4i On
POSTAL13
7-46
Planet and Intelligent Mail Bar
Code On
POSTAL15
7-46
Planet, Postnet, and Postal-4i On
POSTAL21
7-46
Planet, Postnet, and Intelligent
Mail Bar Code On
POSTAL22
7-46
Planet, Postal-4i, and Intelligent
Mail Bar Code On
POSTAL23
7-46
Postnet, Postal-4i, and Intelligent
Mail Bar Code On
POSTAL24
7-46
Planet, Postal-4i, and Postnet with
B and B’ Fields On
POSTAL25
7-46
Planet, Intelligent Mail Bar Code,
and Postnet with B and B’ Fields
On
POSTAL26
7-46
Postal-4i, Intelligent Mail Bar
Code, and Postnet with B and B’
Fields On
POSTAL27
7-46
Planet, Postal-4i, Intelligent Mail
Bar Code, and Postnet On
POSTAL28
7-47
Planet, Postal-4i, Intelligent Mail
Bar Code, and Postnet with B and
B’ Fields On
POSTAL29
7-46
Transmit
PLNCKX1
7-47
*Don’t Transmit
PLNCKX0
7-47
Transmit
NETCKX1
7-47
*Don’t Transmit
NETCKX0
7-47
Page
Bar Output
AUSINT0
7-48
Numeric N Table
AUSINT1
7-48
Alphanumeric C Table
AUSINT2
7-48
Combination N and C Tables
AUSINT3
7-48
Selection
Setting
Serial Command
* Indicates default
# Indicates a numeric entry
Default All China Post (Hong Kong
2 of 5) Settings
CPCDFT
7-48
*Off
CPCENA0
7-48
Page
Postal Codes - Linear
China Post (Hong Kong 2 of 5)
On
CPCENA1
7-48
China Post (Hong Kong 2 of 5) Msg.
Length
Minimum (2 - 80) *4
CPCMIN##
7-48
Maximum (2 - 80) *80
CPCMAX##
7-48
Korea Post
Default All Korea Post Settings
KPCDFT
7-49
*Off
KPCENA0
7-49
On
KPCENA1
7-49
Korea Post Msg. Length
Minimum (2 - 80) *4
KPCMIN##
7-49
Maximum (2 - 80) *48
KPCMAX##
7-49
Transmit Check Digit
KPCCHK1
7-49
*Don’t Transmit Check Digit
KPCCHK0
7-49
Add Code I.D. Prefix to All Symbologies (Temporary)
PRECA2,BK2995C80!
8-1
Show Decoder Revision
REV_DR
8-1
Show Scan Driver Revision
REV_SD
8-1
Show Software Revision
REVINF
8-1
Korea Post Check Digit
Utilities
Show Data Format
Test Menu
Application Plug-Ins (Apps)
Resetting the Factory Defaults
DFMBK3?
8-1
On
TSTMNU1
8-2
*Off
TSTMNU0
8-2
*Decoding Apps On
PLGDCE1
8-2
Decoding Apps Off
PLGDCE0
8-2
*Formatting Apps On
PLGFOE1
8-2
Formatting Apps Off
PLGFOE0
8-2
List Apps
PLGINF
8-2
Remove Custom Defaults
DEFOVR
8-4
Activate Defaults
DEFALT
8-4
9 - 23
9 - 24
10
Product Specifications
Voyager 1602g Wireless Pocket Scanner Product Specifications
Parameter
Specification
Mechanical
Height
.9 in. (22mm)
Length
4.7 in. (120mm)
Width
1.9 in. (48mm)
Weight
3.5 oz. (100g)
Electrical
Battery:
Lithium Ion
3.7v 750mAh
Number of Scans
up to 2250 from full charge
Expected Hours of Operation
12 from full charge
Expected Charge Time
3 - 5 hours
Illumination LED
White emitting color
Aiming
624nm peak wavelength
Radio
Frequency
2.4 to 2.5 GHz (ISM Band) Frequency Hopping Bluetooth v.2.1
Range
33 ft. (10m) line of sight
Data Rate
Up to 1 MBps
Environmental
Operating Temperature
32° to 122°F (0° to 50°C)
Storage Temperature*
4° to 140°F (-20° to 60°C)
Charging Temperature
32° to 104°F (0° to 40°C)
Humidity
Up to 95%, non-condensing
Drop
Operational after 30 drops from 4 feet (1.2m) to concrete
Environmental Sealing
IP42
Vibration
Withstands 10G peak from 10 to 500 Hz
ESD
12kV air, 8kV direct
Image
Image Size
640 x 480 pixels
Scan Performance
Pitch, Skew
+60°, +70°
Motion Tolerance:
up to 10cm per second for 13 mil UPC
Symbol Contrast
Grade 1.0 (20% or greater)
Depth of Field
Typical Performance
5 mil Code 39
39 - 113mm (1.53 - 4.45 in.)
13 mil UPC-A
43 - 293mm (1.69 - 11.53 in.)
20 mil Code 39
59 - 483mm (2.32 - 19.02 in.)
6.7 mil PDF417
47 - 113mm (1.85 - 4.45 in.)
10mil Data Matrix
39 - 114mm (1.53 - 4.49 in.)
20mil QR Code
31 - 245mm (1.22 - 9.65 in.)
Guaranteed Performance
5 mil Code 39
46 - 106mm (1.81 - 4.17 in.)
13 mil UPC-A
51 - 245mm (2.01 - 9.65 in.)
10 - 1
Parameter
Specification
20 mil Code 39
66 - 425mm (2.6 - 16.73 in.)
6.7 mil PDF417
62 - 108mm (2.44 - 4.25 in.)
10mil Data Matrix
54 - 108mm (2.13 - 4.25 in.)
20mil QR Code
41 - 230mm (1.61 - 9.05 in.)
*Storage outside of this temperature range could be detrimental to battery life.
Required Safety Labels
Illumination
output
Compliance
label
locations
Part number,
serial number and
revision
information
location
10 - 2
Standard Connector Pinout
Note: Use of a cable with improper pin assignments may lead to damage to the unit. Use of any cables not provided by the
manufacturer may result in damage not covered by your warranty.
Micro-B USB
1 2 3 4 5
1
2
3
4
5
Vcc
Data Data +
ID
Ground
10 - 3
10 - 4
11
Maintenance and Troubleshooting
Repairs
Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized
service center Customer Support on page -ix.
Maintenance
Your device provides reliable and efficient operation with a minimum of care. Although specific maintenance is not required, the
following periodic checks ensure dependable operation:
Cleaning the Scanner
The scanner’s housing may be cleaned with a soft cloth or tissue dampened with water (or a mild detergent-water solution.)
If a detergent solution is used, rinse with a clean tissue dampened with water only.
!
Caution:
Do not submerge the scanner in water. The scanner’s
housing is not watertight.
Do not use abrasive wipes or tissues on the scanner’s
window – abrasive wipes may scratch the window. Never
use solvents (e.g., acetone) on the housing or window –
solvents may damage the finish or the window.
Cleaning the Window
Reading performance may degrade if the scanner’s window is not clean. If the window is visibly dirty, or if the scanner isn’t
operating well, clean the window with gentle dish soap and water.
Inspecting Cords and Connectors
Inspect the interface cable and connector for wear or other signs of damage. A badly worn cable or damaged connector
may interfere with scanner operation. Contact your distributor for information about cable replacement. Cable replacement
instructions are on page 11-2.
11 - 1
Replacing a Battery
Step 1. Use a Phillips head screwdriver to remove the back cover of the scanner.
Step 2. Lift the back cover up and out to expose the battery.
Step 3. Lift out the battery and replace, making sure the contacts on the battery line up with the contacts in the scanner.
Step 4. Replace the back cover and secure with the Phillips head screw.
11 - 2
Troubleshooting
Note: Make sure that your scanner’s battery is charged.
Visit the Services and Support section of our website (www.honeywellaidc.com) to check for the latest software for
both the scanner and the host.
Is the scanner having trouble reading your symbols?
If the scanner isn’t reading symbols well, check that the symbols:
• Aren’t smeared, rough, scratched, or exhibiting voids.
• Aren’t coated with frost or water droplets on the surface.
• Are enabled in the host to which the scanner connects.
Is the bar code displayed but not entered into the application?
The bar code is displayed on the host device correctly, but you still have to press a key to enter it (the Enter/Return key or
the Tab key, for example).
• You need to program a suffix. Programming a suffix enables the scanner to output the bar code data plus the key you
need (such as “CR”) to enter the data into your application. Refer to Prefix/Suffix Overview on page 5-1 for further
information.
The scanner won’t read your bar code at all.
• Scan the sample bar codes in the back of this manual. If the scanner reads the sample bar codes, check that your bar
code is readable.
Verify that your bar code symbology is enabled (see Chapter 7).
If the scanner still can’t read the sample bar codes, scan All Symbologies on page 7-1.
11 - 3
11 - 4
A
Reference Charts
Symbology Charts
Note: “m” represents the AIM modifier character. Refer to International Technical Specification, Symbology Identifiers, for AIM
modifier character details.
Prefix/Suffix entries for specific symbologies override the universal (All Symbologies, 99) entry.
Refer to Data Editing beginning on page 5-1 and Data Formatting beginning on page 6-1 for information about using Code ID
and AIM ID.
Linear Symbologies
AIM
Symbology
ID
Possible modifiers
(m)
Honeywell
ID
All Symbologies
99
Codabar
]Fm
Code 11
]H3
Code 128
]Cm
Code 32 Pharmaceutical (PARAF)
]X0
Code 39 (supports Full ASCII mode)
]Am
TCIF Linked Code 39 (TLC39)
]L2
Code 93 and 93i
EAN
Hex
0-1
0, 1, 2, 4
0, 1, 3, 4, 5, 7
]Gm
0-9, A-Z,
a-m
]Em
0, 1, 3, 4
a
61
h
68
j
6A
<
3C
b
62
T
54
i
69
d
64
EAN-13 (including Bookland EAN)
]E0
d
64
EAN-13 with Add-On
]E3
d
64
EAN-13 with Extended Coupon Code
]E3
d
64
EAN-8
]E4
D
44
EAN-8 with Add-On
]E3
D
44
y
79
GS1
GS1 DataBar
]em
0
GS1 DataBar Limited
]em
{
7B
GS1 DataBar Expanded
]em
}
7D
GS1-128
]C1
I
49
2 of 5
China Post (Hong Kong 2 of 5)
]X0
Interleaved 2 of 5
]Im
Q
51
e
65
Matrix 2 of 5
]X0
m
6D
NEC 2 of 5
]X0
Y
59
f
66
f
66
g
67
t
74
Straight 2 of 5 IATA
]Rm
Straight 2 of 5 Industrial
]S0
MSI
]Mm
Telepen
]Bm
UPC
0, 1, 3
0, 1, 3
0, 1
0, 1, 2, 3, 8, 9, A, B, C
A-1
AIM
Symbology
UPC-A
ID
Possible modifiers
(m)
]E0
Honeywell
ID
Hex
c
63
UPC-A with Add-On
]E3
c
63
UPC-A with Extended Coupon Code
]E3
c
63
UPC-E
]E0
E
45
UPC-E with Add-On
]E3
E
45
UPC-E1
]X0
E
45
Add Honeywell Code ID
5C80
Add AIM Code ID
5C81
Add Backslash
5C5C
Batch mode quantity
5
35
2D Symbologies
AIM
Honeywell
ID
Possible modifiers
(m)
ID
Hex
Aztec Code
]zm
0-9, A-C
z
7A
Chinese Sensible Code (Han Xin Code)
]X0
H
48
Codablock A
]O6
0, 1, 4, 5, 6
V
56
Symbology
All Symbologies
99
Codablock F
]Om
0, 1, 4, 5, 6
q
71
Code 49
]Tm
0, 1, 2, 4
l
6C
Data Matrix
]dm
0-6
w
77
GS1
]em
0-3
y
79
GS1 Composite
]em
0-3
y
79
GS1 DataBar Omnidirectional
]em
0-3
y
79
MaxiCode
]Um
0-3
x
78
PDF417
]Lm
0-2
r
72
MicroPDF417
QR Code
Micro QR Code
]Lm
0-5
R
52
]Qm
0-6
s
73
s
73
]Qm
Postal Symbologies
AIM
Symbology
ID
Possible modifiers
(m)
Honeywell
ID
All Symbologies
Australian Post
A-2
Hex
99
]X0
A
41
AIM
Symbology
ID
British Post
Possible modifiers
(m)
Honeywell
ID
Hex
]X0
B
42
Canadian Post
]X0
C
43
China Post
]X0
Q
51
InfoMail
]X0
,
2c
Intelligent Mail Bar Code
]X0
M
4D
Japanese Post
]X0
J
4A
KIX (Netherlands) Post
]X0
K
4B
Korea Post
]X0
?
3F
Planet Code
]X0
L
4C
Postal-4i
]X0
N
4E
Postnet
]X0
P
50
ASCII Conversion Chart (Code Page 1252)
In keyboard applications, ASCII Control Characters can be represented in 3 different ways, as shown below. The CTRL+X function is OS and application dependent. The following table lists some commonly used Microsoft functionality. This table applies
to U.S. style keyboards. Certain characters may differ depending on your Country Code/PC regional settings.
Non-printable
characters
ASCII control
Keyboard Control + ASCII (CTRL+X) Mode
Windows Mode Control + X Mode On (KBDCAS2)
DEC
HEX
Char
Control + X Mode Off (KBDCAS0)
CTRL + X
0
00
NUL
Reserved
CTRL+ @
1
01
SOH
NP Enter
CTRL+ A
Select all
2
02
STX
Caps Lock
CTRL+ B
Bold
3
03
ETX
ALT Make
CTRL+ C
Copy
4
04
EOT
ALT Break
CTRL+ D
Bookmark
5
05
ENQ
CTRL Make
CTRL+ E
Center
6
06
ACK
CTRL Break
CTRL+ F
Find
7
07
BEL
Enter / Ret
CTRL+ G
8
08
BS
(Apple Make)
CTRL+ H
History
9
09
HT
Tab
CTRL+ I
Italic
10
0A
LF
(Apple Break)
CTRL+ J
Justify
11
0B
VT
Tab
CTRL+ K
hyperlink
CTRL+ L
list,
left align
Delete
CTRL + X function
12
0C
FF
13
0D
CR
Enter / Ret
CTRL+ M
14
0E
SO
Insert
CTRL+ N
New
15
0F
SI
ESC
CTRL+ O
Open
16
10
DLE
F11
CTRL+ P
Print
17
11
DC1
Home
CTRL+ Q
Quit
18
12
DC2
PrtScn
CTRL+ R
19
13
DC3
Backspace
CTRL+ S
20
14
DC4
Back Tab
CTRL+ T
21
15
NAK
F12
CTRL+ U
22
16
SYN
F1
CTRL+ V
Save
Paste
A-3
Non-printable
characters
ASCII control
Keyboard Control + ASCII (CTRL+X) Mode
Windows Mode Control + X Mode On (KBDCAS2)
DEC
HEX
Char
Control + X Mode Off (KBDCAS0)
CTRL + X
23
17
ETB
F2
CTRL+ W
24
18
CAN
F3
CTRL+ X
25
19
EM
F4
CTRL+ Y
26
1A
SUB
F5
CTRL+ Z
27
1B
ESC
F6
CTRL+ [
28
1C
FS
F7
CTRL+ \
29
1D
GS
F8
CTRL+ ]
30
1E
RS
F9
CTRL+ ^
31
1F
US
F10
CTRL+ -
127
7F
⌂
NP Enter
CTRL + X function
Lower ASCII Reference Table
Note: Windows Code page 1252 and lower ASCII use the same characters.
Printable Characters
DEC
HEX
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
A-4
Character
<SPACE>
!
"
#
$
%
&
'
(
)
*
+
,
.
/
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
DEC
HEX
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
Character
@
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
DEC
HEX
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
Character
`
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
{
|
}
¯
Printable Characters (Continued)
DEC
HEX
Character
DEC
HEX
63
3F
95
5F
DEC
HEX
CP 1252
ASCII
Alternate Extended
PS2 Scan Code
128
80
€
Ç
up arrow ↑
0x48
129
81
ü
down arrow ↓
0x50
130
82
‚
é
right arrow →
0x4B
131
83
ƒ
â
left arrow ←
0x4D
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
84
85
86
87
88
89
8A
8B
8C
8D
8E
8F
90
91
92
93
94
95
96
97
98
99
9A
9B
9C
9D
9E
9F
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
AA
AB
AC
AD
AE
„
…
†
‡
ˆ
‰
Š
‹
Œ
ä
à
å
ç
ê
ë
è
ï
î
ì
Ä
Å
É
æ
Æ
ô
ö
ò
û
ù
ÿ
Ö
Ü
¢
£
¥
₧
ƒ
á
í
ó
ú
ñ
Ñ
ª
º
¿
⌐
¬
½
¼
¡
«
Insert
Delete
Home
End
Page Up
Page Down
Right ALT
Right CTRL
Reserved
Reserved
Numeric Keypad Enter
Numeric Keypad /
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
Numeric Keypad +
Numeric Keypad Numeric Keypad *
Caps Lock
Num Lock
Left Alt
Left Ctrl
Left Shift
Right Shift
Print Screen
Tab
Shift Tab
Enter
Esc
Alt Make
Alt Break
Control Make
Control Break
Alt Sequence with 1 Character
0x52
0x53
0x47
0x4F
0x49
0x51
0x38
0x1D
n/a
n/a
0x1C
0x35
0x3B
0x3C
0x3D
0x3E
0x3F
0x40
0x41
0x42
0x43
0x44
0x57
0x58
0x4E
0x4A
0x37
0x3A
0x45
0x38
0x1D
0x2A
0x36
n/a
0x0F
0x8F
0x1C
0x01
0x36
0xB6
0x1D
0x9D
0x36
?
Character
DEC
_
127
HEX
7F
Character
⌂
Extended ASCII Characters
Ž
‘
’
“
”
•
–
—
˜
™
š
›
œ
ž
Ÿ
¡
¢
£
¤
¥
¦
§
¨
©
ª
«
¬
®
A-5
Extended ASCII Characters (Continued)
DEC
HEX
CP 1252
ASCII
Alternate Extended
PS2 Scan Code
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
AF
B0
B1
B2
B3
B4
B5
B6
B7
B8
B9
BA
BB
BC
BD
BE
BF
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
CA
CB
CC
CD
CE
CF
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
DA
DB
DC
DD
DE
DF
E0
E1
E2
¯
°
±
²
³
´
µ
¶
·
¸
¹
º
»
¼
½
¾
¿
À
Á
Â
Ã
Ä
Å
Æ
Ç
È
É
Ê
Ë
Ì
Í
Î
Ï
Ð
Ñ
Ò
Ó
Ô
Õ
Ö
×
Ø
Ù
Ú
Û
Ü
Ý
Þ
ß
à
á
â
»
░
▒
▓
│
┤
╡
╢
╖
╕
╣
║
╗
╝
╜
╛
┐
└
┴
┬
├
─
í
╞
╟
╚
╔
╩
╦
╠
═
╬
╧
╨
╤
╥
╙
╘
╒
╓
╫
╪
┘
┌
█
▄
▌
▐
▀
α
ß
Γ
Ctrl Sequence with 1 Character
0x1D
A-6
Extended ASCII Characters (Continued)
DEC
HEX
CP 1252
ASCII
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
E3
E4
E5
E6
E7
E8
E9
EA
EB
EC
ED
EE
EF
F0
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
FC
FD
FE
FF
ã
ä
å
æ
ç
è
é
ê
ë
ì
í
î
ï
ð
ñ
ò
ó
ô
õ
ö
÷
ø
ù
ú
û
ü
ý
þ
ÿ
π
Σ
σ
µ
τ
Φ
Θ
Ω
δ
∞
φ
ε
∩
≡
±
≥
≤
⌠
⌡
÷
≈
°
·
·
√
ⁿ
²
■
Alternate Extended
PS2 Scan Code
ISO 2022/ISO 646 Character Replacements
Code pages define the mapping of character codes to characters. If the data received does not display with the proper characters, it may be because the bar code being scanned was created using a code page that is different from the one the host program is expecting. If this is the case, select the code page with which the bar codes were created. The data characters should
then appear properly.
Code Page Selection Method/Country
Standard
Keyboard Country
Honeywell Code Page
Option
United States
(standard ASCII)
ISO/IEC 646-IRV
n/a
1
Automatic National Character
Replacement
ISO/IEC 2022
n/a
2 (default)
Binary Code page
n/a
n/a
3
Default “Automatic National Character replacement” will select the below Honeywell Code Page options for Code128, Code
39 and Code 93.
United States
ISO/IEC 646-06
0
1
Canada
ISO /IEC 646-121
54
95
Canada
ISO /IEC 646-122
18
96
Japan
ISO/IEC 646-14
28
98
A-7
Code Page Selection Method/Country
Standard
Keyboard Country
Honeywell Code Page
Option
China
ISO/IEC 646-57
92
99
Great Britain (UK)
ISO /IEC 646-04
7
87
France
ISO /IEC 646-69
3
83
Germany
ISO/IEC646-21
4
84
Switzerland
ISO /IEC 646-CH
6
86
Sweden / Finland (extended Annex C)
ISO/IEC 646-11
2
82
Ireland
ISO /IEC 646-207
73
97
Denmark
ISO/IEC 646-08
8
88
Norway
ISO/IEC 646-60
9
94
Italy
ISO/IEC 646-15
5
85
Portugal
ISO/IEC 646-16
13
92
Spain
ISO/IEC 646-17
10
90
Spain
ISO/IEC 646-85
51
91
A-8
64
91
92
93
94
96
123
124
125
126
Hex
23
24
40
5B
5C
5D
5E
60
7B
7C
7D
7E
US
0
1
#
$
@
[
\
]
^
`
{
|
}
~
CA
54
95
#
$
à
â
ç
ê
î
ô
é
ù
è
û
CA
18
96
#
$
à
â
ç
ê
É
ô
é
ù
è
û
JP
28
98
#
$
@
[
¥
]
^
`
{
|
}
⎯
CN
92
99
#
¥
@
[
\
]
^
`
{
|
}
⎯
GB
7
87
£
$
@
[
\
]
^
`
{
|
}
˜
FR
3
83
£
$
à
°
ç
§
^
µ
é
ù
è
¨
DE
4
84
#
$
§
Ä
Ö
Ü
^
`
ä
ö
ü
ß
CH
6
86
ù
$
à
é
ç
ê
î
ô
ä
ö
ü
û
SE/FI
2
82
#
¤
É
Ä
Ö
Å
Ü
é
ä
ö
å
ü
DK
8
88
#
$
@
Æ
Ø
Å
^
`
æ
ø
å
˜
NO
9
94
#
$
@
Æ
Ø
Å
^
`
æ
ø
å
IE
73
97
£
$
Ó
É
Í
Ú
Á
ó
é
í
ú
á
IT
5
85
£
$
§
°
ç
é
^
ù
à
ò
è
ì
PT
13
92
#
$
§
Ã
Ç
Õ
^
`
ã
ç
õ
°
ES
10
90
#
$
§
¡
Ñ
¿
^
`
°
ñ
ç
˜
ES
51
91
#
$
∙
¡
Ñ
Ç
¿
`
´
ñ
ç
¨
Honeywell
CodePage
36
Country Keyboard
35
COUNTRY
Dec
ISO / IEC 646 National Character Replacements
A-9
Keyboard Key Maps
6E
70 71 72 73
74 75 76 77
78 79 7A 7B
7C 7D 7E
01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F
10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D
1E 1F 20 21 22 23 24 25 26 27 28 29 2B
4B 50 55
4C 51 56
2C 2E 2F 30 31 32 33 34 35 36 37
39
3D
3A 3B 3C
3E 3F 38 40
53
4F 54 59
5A 5F
5B 60
5C 61
5D 62
63
64 69
65
6A
66
67
6C
68
5A 5F
5B 60
5C 61
5D 62
63
64 69
65
6A
66
67
6C
68
104 Key U.S. Style Keyboard
6E
70 71 72 73
74 75 76 77
78 79 7A 7B
7C 7D 7E
01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F
10 11 12 13 14 15 16 17 18 19 1A 1B 1C 2B
1E 1F 20 21 22 23 24 25 26 27 28 29 2A
4B 50 55
4C 51 56
2C 2D 2E 2F 30 31 32 33 34 35 36 37
39
3D
3A 3B 3C
3E 3F 38 40
53
4F 54 59
105 Key European Style Keyboard
A - 10
Sample Symbols
UPC-A
Interleaved 2 of 5
0 123456 7890
1234567890
EAN-13
9 780330 290951
Code 128
Code 128
Code 39
BC321
Codabar
A13579B
Code 93
123456-9$
Straight 2 of 5 Industrial
123456
Matrix 2 of 5
6543210
GS1 DataBar
(01)00123456789012
PDF417
Car Registration
Data Matrix
Test Symbol
QR Code
Aztec
Numbers
Package Label
MaxiCode
Micro PDF417
Test Message
Test Message
Postnet
Zip Code
4-CB (4-State Customer Bar Code)
01,234,567094,987654321,01234567891
ID-tag (UPU 4-State)
J18CUSA8E6N062315014880T
Programming Chart
0
1
2
3
4
5
6
7
8
9
Programming Chart
A
B
C
D
E
F
Save
Discard
Reset
Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or
digits, and Save again.
Honeywell Scanning & Mobility
9680 Old Bailes Road
Fort Mill, SC 29707
www.honeywellaidc.com
VG1602-UG Rev C
3/16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising