ComColor Safety Guide
Safety Information
Applicable Printer models
9050/9050R
7050/7050R/7010/7010R
3050/3050R/3010/3010R
050-36304-008
CAUTION
To ensure safety precautions, be sure to read this guide before using the product.
After reading this guide, keep it in handy for future reference.
1
ComColor Series Safety Information 01
Index
Safety Precautions .................................................................................................... 4
Warning Symbols
Installation Location
Power Connection
Handling
Ink Cartridge
Before Use ................................................................................................................. 6
Installation Location
Power Connection
Connecting to a Computer
Required Spacing
Handling
Originals
Printable Area
Printing Paper
Printouts
Materials Not to Be Printed
Ink Cartridge Storage and Handling Precautions
Disposing of Used Ink Cartridges and Cleaning Tanks
Specifications .......................................................................................................... 15
ComColor Series Safety Information 01
2
ComColor Series
Model:SE-H301/SE-M301/SE-L301/SE-M401/SE-L401
This Product Contains RFID (Radio Frequency Identification) System
Model: 050-34901
Contains FCC ID: RPARFR6
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
The user is cautioned that unauthorised changes or modifications not approved could void the user’s authority to operate
the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.
Contains IC: 4819A-RFR6
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Perchlorate Material-special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate
This product may contain certain substances which are restricted when disposed.
Therefore, be sure to consult your contracted service dealer.
Countries of Intended Use
Austria/Belgium/Denmark/Finland/France/Germany/Greece/Iceland/Ireland/Italy/Luxembourg/Netherlands/Norway/
Portugal/Spain/Sweden/Switzerland/U.K.
Copyright © 2009 RISO KAGAKU CORPORATION
3
ComColor Series Safety Information 01
Safety Precautions
This section describes the items that should be followed for safe use of this machine. Be sure to read this section before
using the machine.
Warning Symbols
To use the machine properly and to prevent human injury and damage to properties, the following warning symbols are
used. Read the meaning of the symbols to understand and then read this guide.
WARNING
Indicates that incorrect handling by ignoring this symbol may cause death or serious
human injury.
CAUTION
Indicates that incorrect handling by ignoring this symbol may cause human injury or
damage to properties.
Examples of symbols
The
symbol indicates a prohibited action. A specific prohibited action is drawn inside or next to
the symbol. (The left figure indicates that disassembly is prohibited.)
The
symbol indicates a forced action or an instruction.
A specific instruction is drawn inside the symbol. (The left figure indicates an instruction to remove
the power plug from the electrical outlet.)
Installation Location
CAUTION
■ Place the machine on a flat or stable surface. Otherwise, the machine might be inclined or fall down, resulting
in human injury.
■ When installing the machine without the use of a special scanner stand, do not install the machine in a
location where it will be exposed to vibration from other machines.
Otherwise, the machine may drop or fall and injure someone.
■ The machine has ventilation openings. Place the machine at least 100 mm (3 15/16") from walls. If the
ventilation openings are blocked, the inside of the machine may become hot and a fire might occur.
■ Do not place the machine in a dusty or humid location. Otherwise, a fire or an electric shock might occur.
Power Connection
WARNING
■ Install the machine near the wall socket to avoid using an extension cord between the machine and the wall
socket. If an extension cord is absolutely required, do not use longer than 5m (15ft). Otherwise, a fire or an
electric shock might occur.
■ Do not damage or rebuild the power cord. Placing a heavy object on the cord or pulling or forcibly
bending the cord may damage the cord, resulting in a fire or an electric shock.
■ The power cord supplied with this product can be used only for this machine. Do not use it for another
electric product. Otherwise, a fire or an electric shock might occur.
■ Do not connect a power cord other than the scanner (HS4000) cord to the scanner socket on the machine.
■ Do not plug or unplug the power cord if your hands are wet. Otherwise, an electric shock might occur.
CAUTION
■ Connect the plug securely to the electrical outlet to avoid a loose connection.
■ Do not pull the power cord when unplugging it. Otherwise, it could become damaged and a fire or an electric
shock might occur. Be sure to hold on to the plug when unplugging the power cord.
■ If the machine will not be used for a long time, such as during a holiday, unplug the power cord from the
electrical outlet for safety.
■ Pull out the power plug from the electrical outlet at least once a year and clean the prongs of the plug and
their surroundings. Dust collected on these areas can result in fire.
ComColor Series Safety Information 01
4
Handling
WARNING
■ Do not place water containers or metallic objects on the machine. If water drips inside the machine or a
metallic object drops inside it, a fire or an electric shock might occur.
■ Do not insert or drop any metallic material or flammable substances into the machine through any opening.
A fire or an electric shock might occur.
■ Do not remove the covers. Otherwise, you might be electrically shocked by the high-voltage part inside.
■ Do not disassemble or rebuild the machine by yourself. Otherwise, a fire or an electric shock might
occur.
■ If the unit emits excessive heat, smoke or foul odour, immediately turn off the main power switch,
unplug the power cord and contact your service representative. Otherwise, a fire or an electric shock
might occur.
■ If something drops inside the unit, immediately turn off the main power switch, unplug the power cord
and contact your service representative. Continued use might result in a fire or an electric shock.
■ When using the IC card reader
The IC card reader continually emits a weak signal. If you are using a cardiac pacemaker and notice any
abnormalities, immediately move away from the machine. Consult a physician immediately.
CAUTION
■ Do not insert your fingers in the areas around the standard tray or stacking tray.
Otherwise, an injury may occur.
■ The inside of the printer may have areas with ink. Be careful not to let the ink come in contact with your
hands or clothing.
Should ink accidentally make contact with your hands, wash it off with detergent as soon as possible.
■ When moving the machine, contact your service representative.
If you try to forcibly move the machine, the machine may overturn, resulting in injury.
Ink Cartridge
CAUTION
■ Avoid contact to eyes and/or skin. If ink gets into your eyes, flush it out immediately with plenty of water.
If ink comes in contact with your skin, wash it off thoroughly using soap.
■ Allow plenty of ventilation during printing. Seek fresh air immediately if you feel unwell during use.
■ If you feel sick, seek medical advice immediately.
■ Use the ink only for printing purposes.
■ Do not dispose of used ink cartridges by burning. The ink is combustible and can cause the fire to grow,
resulting in burns.
■ Store ink cartridges out of the reach of children.
■ The ink is a combustible liquid. In the event of fire, use potassium carbonate mist, foam, powder, or a
carbon dioxide fire extinguisher.
5
ComColor Series Safety Information 01
Before Use
This section describes the precautions that must be observed before using the machine.
Installation Location
Observe the following precautions.
■ Your dealer will help you to determine a proper location for the machine at the time of delivery.
■ When moving the machine, contact your service representative.
■ Avoid installing the machine in the following locations. Otherwise, incorrect operation, malfunction, or
accident might occur.
• Places subject to direct sunlight or excessively illuminated such as next to windows
(if inevitable, use a curtain at the window)
• Places subject to sudden temperature variations
• Places excessively hot and humid or cold and dry
• Places close to fire or heat
• Places directly subject to cold air from air conditioners or hot air from heaters, as well as radiant heat
• Places with poor air permeability or ventilation
• Dusty places
• Places subject to excessive vibration
■ Install the machine in a place whose levelness is within the following specified range.
Installation surface level: 2° or less
■ Operate the machine under the following environment conditions.
Temperature range: 15°C to 30°C (59°F to 86°F)
Humidity range: 40% to 70% RH (non-condensing)
Power Connection
Observe the following precautions.
■ Connect the plug securely to the optional connection outlet on the printer main unit to avoid a loose
connection.
■ Install the machine near an electrical outlet.
■ When the scanner is connected to the optional connection outlet on the printer main unit, the scanner is
turned ON and OFF by the power of the main unit.
ComColor Series Safety Information 01
6
Connecting to a Computer
■ Connecting to Multiple Computers
Hub
Ethernet shielded cable
(straight-through cable)
■ Connecting to One Computer
Ethernet shielded cable
(crossover cable)
The maximum allowable voltage for all input/output connection is 5V.
● Use a commercially available ethernet shielded cable.
It is recommended that you use one of the following types of ethernet shielded cables according to your network
environment.
• Cat 5 (Cat 5e) cable for 100BASE network
• Cat 6 cable for 1000BASE network
● To print from a computer, you must install the printer driver. For the installation method, see "Installing the
Printer Driver" in the "Basic Guide".
7
ComColor Series Safety Information 01
Required Spacing
■ Main Unit
Provide sufficient space for the front cover to open.
● As seen from the front
● As seen from the side
1020
(40 3/16")
695 (27 3/8")
1210 (47 5/8")
100
(3 15/16")
1230 (48 7/16")
Units: mm (inch)
■ Main Unit with Optional Equipment Installed
Provide sufficient space for opening the front covers and original cover of the scanner.
● As seen from the front
1220 (48")*2
2295(90 3/8")*1
Units: mm (inch)
ComColor Series Safety Information 01
8
● As seen from the side
1610
(63 3/8")
800 (31 1/2")
1335 (52 9/16")*3
100 (3 15/16")
Units: mm (inch)
The size varies depending on the optional equipment used.
*1
Width
*2
Height
*3
Depth
Main unit only
1,210 mm (47 5/8")
Main unit and Scanner (when using special scanner stand)
1,220 mm (48")
Main unit and Face Down Offset Tray
1,240 mm (48 13/16")
Main unit and Wide Stacking Tray
1,830 mm (72 1/16")
Main unit and Auto-control Stacking Tray
1,710 mm (67 5/16")
Main unit, Face Down Offset Tray, and Wide Stacking Tray
1,860 mm (73 1/4")
Main unit, Face Down Offset Tray, and Auto-control Stacking Tray
1,740 mm (68 1/2")
Main unit and Multifunction Finisher
2,295 mm (90 3/8")
Main unit only
1,020 mm (40 1/8")
Main unit and Scanner (when using special scanner stand)
1,220 mm (48")
Main unit and Multifunction Finisher
1,165 mm (45 7/8")
Main unit and Face Down Offset Tray
1,105 mm (43 1/2")
Main unit only
1,230 mm (48 7/16")
Main unit and Scanner (when using special scanner stand)
1,335 mm (52 9/16")
Main unit and Multifunction Finisher
1,275 mm (50 3/16")
The ComColor 9050 is used in the illustration of this machine.
A multifunction finisher cannot be connected to the ComColor 7010, 7010R, 3010, or 3010R.
9
ComColor Series Safety Information 01
Handling
■ Do not use the main power switch to turn the machine OFF or unplug the machine during operation.
■ Do not open any of the covers during operation.
■ Do not move the machine.
■ The machine contains precision components and moving parts. Therefore, do not perform operations not
described in the guides.
■ Do not place heavy objects on the machine or subject the machine to strong shocks.
■ Open and close the covers gently.
■ After turning the main power switch OFF, wait until the main power lamp goes off before turning the main
power switch ON.
■ Perform head-cleaning if the machine will not be used for a long time or before using the machine after
a long period of non-use.
Ink may deteriorate or dry up in the ink feed path inside the machine, resulting in clogging of the print head.
It is recommended that head-cleaning be performed regularly to prevent this from occurring.
■ Do not touch the print head, as this can result in malfunction or deterioration in print quality.
■ Always keep the four color ink cartridges in the machine. Do not leave the machine with the ink
cartridges removed, even when not using the machine.
Originals
If you connect the optional scanner, you can copy or scan an original by placing it on the platen glass or in the ADF to be
read.
If you use an original that is not compatible with this machine, it may result in problems such as paper jamming, soiling or
malfunctions.
Specifications of Original Source
Platen Glass
Original Size
Maximum 303 mm × 432 mm (11 15/16" × 17")
ADF
100 mm × 148 mm - 297 mm × 432 mm
(3 15/16" × 5 13/16"- 11 11/16" × 17")
Original Weight
-*1
52 g/m2 (14-lb bond) to 128 g/m2 (34-lb bond)
Original Type
-
Plain paper
Max. Capacity
-
100 sheets*2
glass durability: 200 N (over an A3-size area)
*12 Platen
and the weight is 80 g/m2 (21-lb bond) or less
* When the size is A4/Letter
2
60 sheets (80 g/m (21-lb bond)) or less for a paper size exceeding B4
■ Precautions about Originals
Originals that have ink or correcting fluid must be dried before being placed on the platen glass.
The following types of originals cannot be scanned using the ADF, even when within the above specification range.
Use the platen glass instead.
• Paper that has been cut and pasted
• Heavily wrinkled or curled paper
• Folded paper
• Glued paper
• Paper with holes
• Torn paper or paper with irregular edges
• Transparencies, tracing paper, and other highly transparent materials
• Art paper or coated paper with a processed surface on the front or back
• Thermal paper for fax machines or word processors
• Paper with an uneven surface
ComColor Series Safety Information 01
10
Printable Area
The size of the printable area varies depending on whether you are printing a job from a computer or copying
a paper original.
■ Maximum Print Area
Maximum Print Area
Model
Printing
Print Area (Margin)
Copying
Standard
mm*1
Maximum
ComColor 9050/9050R/7050/7050R
314 mm × 548 mm
(12 3/8" × 21 9/16")
295 mm × 430
(11 5/8" × 16 15/16")
3 mm (1/8")
1 mm (0.04")
ComColor 7010/7010R
310 mm × 544 mm
(12 3/16" × 21 7/16")
295 mm × 430 mm*1
(11 5/8" × 16 15/16")
5 mm (3/16")
3 mm (1/8")
ComColor 3050/3050R/3010/3010R
210 mm × 544 mm
(8 1/4" × 21 7/16")
210 mm × 430 mm*2
(8 1/4" × 16 15/16")
*1 When using the platen glass: 303 mm × 432 mm (11 15/16" × 17")
*2 When using the platen glass: 210 mm × 432 mm (8 1/4" × 17")
Printing without margins cannot be performed. Margins are always added around the edges of the paper.
■ Printable Area (Margin)
Some areas around the edges of the paper cannot be printed regardless of the data size of the original. The size of the
blank margin left by the edges of the paper (where printing is not possible) varies depending on the model.
See "Maximum Print Area".
Printable area
margin
margin
● When [Printable area] is set to [Maximum] in [Admin. Settings], the printable area can be changed to 1 mm
(0.04") from the edge of the paper. Depending on the content of the original, text or images may be lost or
bleeding may occur.
● Even when the paper size is within the maximum print area, a margin is always provided.
● When copying, the machine cannot scan the 1 mm (0.04") margin of the original.
■ Printable Area of Envelopes
• C4: 229 mm × 324 mm (9" × 12 3/4")
• C5: 162 mm × 229 mm (6 3/8" × 9")
• C6: 114 mm × 162 mm (4 1/2" × 6 3/8")
• DL-R: 110 mm × 220 mm (4 5/16" × 8 11/16")
• Envelope 229 mm × 305 mm (9" × 12")
• Envelope 254 mm × 331 mm (10" × 13")
• NO.10 envelope 105 mm × 242 mm (4.125" × 9.5")
The printable area on envelopes is the area enclosed within 10 mm (3/8") of the edges of the envelope.
Any part of the image that does not fit within the printable area is not printed.
11
ComColor Series Safety Information 01
Envelope size
10mm (3/8")
Printable area
Output direction
10mm (3/8")
10mm (3/8")
10mm (3/8")
● You cannot print on envelopes without an optional stacking tray or multifunction finisher.
● To also print on the flap section, you must register the envelope size including the flap section. For more
information, contact the dealer (or the maintenance or service company).
● You cannot use duplex print when printing on envelopes.
Printing Paper
■ If you use paper that is not compatible with this machine, it may result in problems such as paper
jamming, soiling or malfunctions.
■ The specifications for the paper that can be loaded in the feed tray and standard tray differ.
Paper Basic Specifications
Feed tray
Standard Tray
Size
182 mm × 182 mm - 297 mm × 420 mm
(7 3/16" × 7 3/16" - 11 11/16" × 17")
90 mm × 148 mm - 340 mm × 550 mm
(3 9/16" × 5 13/16" - 13 3/8" × 21 5/8")
Weight
52 g/m2 (14-lb bond) to 104 g/m2 (28-lb bond)
(45 kg - 90 kg (99 lb - 198 lb) Ream weight:
duodecimo)
46 g/m2 (12-lb bond) to 210 g/m2 (56-lb bond)
(40 kg - 180 kg (88 lb - 397 lb) Ream weight:
duodecimo)
Paper Type
Plain paper, recycled paper
Plain paper, recycled paper, envelopes, postcards
(plain paper), postcards (inkjet)
Maximum Load
500 sheets in each tray*
(or hight up to 50 mm (1 15/16"))
1000 sheets*
(or hight up to 110 mm (4 5/16"))
2
* When the weight is 85 g/m
(23-lb bond)
■ Acceptable paper sizes depend on the output tray.
Face Down Tray: 90 mm × 148 mm - 340 mm × 550 mm (3 9/16" × 5 13/16" - 13 3/8" × 21 5/8")
(Envelopes are not acceptable.)
Face Down Offset Tray: When printouts are not collated: 90 mm × 148 mm - 340 mm × 550 mm
(3 9/16" × 5 13/16" - 13 3/8" × 21 5/8") (Envelopes are not acceptable.)
When offset output is applied: Paper width 131 mm - 305 mm (5 3/16" - 12")
(Envelopes are not acceptable.)
RISO Auto-control Stacking Tray: 100 mm × 148 mm - 320 mm × 432 mm (3 15/16" × 5 13/16" - 12 5/8" × 17")
(When using paper exceeding 432 mm (17") , close the paper guides.)
Wide Stacking Tray: 90 mm × 148 mm - 340 mm × 550 mm (3 9/16" × 5 13/16" - 13 3/8" × 21 5/8")
For information on each tray in the multifunction finisher, see "Multifunction Finisher (Optional)" in "Specifications".
ComColor Series Safety Information 01
12
● The feed tray is not available for ComColor 7010/7010R/3010/3010R.
● Depending on the type of paper, operating environment, and storage conditions, even paper meeting these size
and weight specifications may not be able to pass through the machine in some cases.
■ Do not use the following paper types as they will cause problems such as paper jamming or
malfunctions.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Paper that does not comply with the conditions in the basic specifications
Paper with a processed surface, such as thermal paper or carbon paper
Curled paper (3 mm (1/8") or more)
Paper with wrinkles
Bent paper
Torn paper
Paper with ripples
Coated paper such as art paper
Paper with jagged edges
Glued paper
Paper with holes
Glossy paper for photographs
Transparencies
Yupo paper
■ Always use paper from a sealed package.
■ After finishing the print job, return the unused paper from the standard tray to the package and store. If
you leave the paper in the standard tray, the paper may curl and cause paper jamming.
■ If the paper is not cut cleanly or has a textured surface (such as drawing paper), fan the paper before
use.
■ Store paper flat, away from high temperatures, high humidity, and direct sunlight.
Printouts
■ When using duplex printing, the edges of the paper may become dirty depending on the original.
■ Printouts lose their color (discolor) over time due to various chemicals in the air and light.
You can protect printouts against discoloration by allowing the printout to fully dry and then inserting it
into a glass frame or laminating it.
■ When storing printouts in a clear file folder, be sure to use only those made of polyethylene
terephthalate (PET).
■ Printouts can lose color when they come in contact with water or sweat. Avoid storing printouts in a
place subject to moisture.
Writing on printouts with an oil-based pen can cause bleeding.
■ The print density of the printout immediately after printing differs from the print density 24 hours later.
Print density decreases over time.
■ Do not place printouts from this machine on top of printouts from a laser printer or copier that uses
toner. The paper might stick to the printed toner and the toner might transfer to the printout.
13
ComColor Series Safety Information 01
Materials Not to Be Printed
■ Do not use the machine in any manner which violates the law or infringes on established copyrights, even
when making copies for personal use. Consult your service representatives for further details. In general, use
discretion and common sense.
Ink Cartridge Storage and Handling Precautions
Ink cartridges for this machine are made of paper. For this reason, cartridges may become deformed and
unusable if stored incorrectly or in an unsuitable environment. Store the ink cartridges properly, according to
"Storage".
■ Storage
● Be sure to store the ink cartridge horizontally in the direction indicated by the this-side-up mark.
● Avoid freezing or placement under direct sunlight. Store in areas between 5ºC and 35ºC (41ºF - 95ºF).
Do not store in locations subject to extreme changes in temperature.
● If the plastic bag is opened but the ink cartridge is not to be used right away, store the ink cartridge properly and
insert it into the machine as soon as possible.
■
●
●
●
●
Handling Precautions
Do not shake the ink cartridge. This can create bubbles, resulting in a deterioration in print quality.
Do not add ink into the ink cartridge.
Remove the ink cartridge from its plastic bag just before inserting it into the machine.
Adequate operation temperature is 15ºC - 30ºC (59ºF - 86ºF).
Using the ink cartridge outside the adequate operation temperature range can result in a deterioration in print
quality (reduced ink discharge).
The spraying properties of the inkjet printer can vary depending on the ink viscosity. In particular, at lower
temperatures, the ink viscosity increases and can result in clogging of the print head. Follow the information on the
operation environment and storage temperature, check the manufacturing date, and use soon after purchase.
● If the cover of the ink cartridge is removed and the ink cartridge is left for a long period of time without being used
up, various chemicals in the air can cause the ink cartridge to deteriorate.
Using ink that has deteriorated or changed in quality can damage the print head or ink flow path.
● Do not dump the ink left in the cartridge into the sewers.
● The ink is a combustible liquid.
In the event of fire, use potassium carbonate mist, foam, powder, or a carbon dioxide fire extinguisher.
Disposing of Used Ink Cartridges and Cleaning Tanks
■ The ink in the cleaning tank cannot be used for printing.
ComColor Series Safety Information 01
14
Specifications
■ ComColor 9050/9050R Specifications
Basic Functions and Print Functions
Model
SE-H301
Type
Console
Color Support
Full color
Print Type
Line-type inkjet system
Ink Type
Oil-based pigment ink (Cyan, Magenta, Yellow, Black)
Standard: 300 dpi (main scanning direction) × 300 dpi (sub-scanning direction)
Resolution
Fine: 300 dpi (main scanning direction) × 600 dpi (sub-scanning direction)
Number of Gray Levels
For each CMYK color (8 gray levels)
Data Processing Resolution
Standard: 300 dpi × 300 dpi
Fine: 300 dpi × 600 dpi
Line smoothing: 600 dpi × 600 dpi
Warm-up Time
2 min. 45 sec. or less (at room temperature of 20ºC (68ºF))
Monochrome: 8 sec or less*1 (when copying A4-R/Letter-R
orientation using monochrome mode)
First Print Time
Color: 8 sec or less*1 (when copying A4-R/Letter-R orientation using
color mode)
Continuous Print Speed
*2*7
A4-R
Simplex: 150 ppm
Duplex: 75 sheets/minute (150 ppm)
Letter-R
Simplex: 146 ppm
Duplex: 73 sheets/minute (146 ppm)
A4
Simplex: 110 ppm
Duplex: 55 sheets/minute (110 ppm)
Letter
Simplex: 116 ppm
Duplex: 58 sheets/minute (116 ppm)
B4/Legal
Simplex: 90 ppm
Duplex: 42 sheets/minute (90 ppm)
A3
Simplex: 80 ppm
Duplex: 40 sheets/minute (80 ppm)
Ledger
Simplex: 78 ppm
Duplex: 39 sheets/minute (78 ppm)
Duplex Printing
Standard
Standard Tray
Maximum: 340 mm × 550 mm (13 3/8" × 21 5/8")
Minimum: 90 mm × 148 mm (3 9/16" × 5 13/16")
Feed Tray
Maximum: 297 mm × 420 mm (11 11/16" × 17")
Minimum: 182 mm × 182 mm (7 3/16" × 7 3/16")
Paper Size
Printable Area
Maximum: 314 mm × 548 mm (12 3/8" × 21 9/16")
Guaranteed Print Area*3
Standard: Margin width of 3 mm (1/8")
Maximum: Margin width of 1 mm (0.04")
Paper Weight
Paper Feed Method/Paper
*4
Tray Capacity
Standard Tray
46 g/m2 (12-lb bond) to 210 g/m2 (56-lb bond) (plain paper)
Feed Tray
52 g/m2 (14-lb bond) to 104 g/m2 (28-lb bond) (plain paper)
Standard Tray
1,000 sheets (Height up to 110 mm (4 5/16"))
Feed Tray
500 sheets × 3 trays (Height up to 50 mm (1 15/16"))
Continuous Printing Capacity
Output Tray Capacity
15
9,999 sheets
Standard
500 sheets (Height up to 60 mm (2 3/8"))
Option
1,000 sheets (when using the optional auto-control stacking tray or
wide stacking tray)
*4
Page Description Language
Original PDL
Supported Protocols
TCP/IP, HTTP, HTTPs (SSL), DHCP, ftp, lpr, IPP, SNMP,
Port 9100 (RAW port)
ComColor Series Safety Information 01
Microsoft® Windows® 2000
Microsoft® Windows® XP (32-bit version)
Supported Operating Systems
Microsoft® Windows Server 2003 (32-bit version)
Microsoft® Windows 2000 Server
Microsoft® Windows Vista® (32-bit version)
Installed Fonts
None
Emulation
None
Network Interface
Ethernet 1000BASE-T, 100BASE-TX, 10BASE-T (2ch)
CPU
Intel® Celeron®-M440 (1.86 GHz)
Memory Capacity
1 GB
Hard Disk*6
Capacity
160 GB
Available Space
140 GB
Operating System
Linux
Power Source
AC 100-240 V, 10-5 A, 50-60 Hz
Max. 1,000 W
Power Consumption
Ready*5: 250 W
Sleep: Max. 45 W
Stand-by: Max. 1 W
Operating Noise
Max. 68 dB (when printing)
Operating Environment
Temperature: 15ºC to 30ºC (59ºF to 86ºF)
Humidity: 40% to 70% RH (non-condensing)
Dimensions (W × D × H)
In use: 1,210 mm × 695 mm × 1,020 mm
(47 5/8" × 27 3/8" × 40 3/16")
Weight
180 kg (397 lb)
Required Space (W × D × H)
With front cover and feed tray extended:
1,210 mm × 1,230 mm × 1,020 mm (47 5/8" × 48 7/16" × 40 3/16")
With face down tray and standard tray stored:
1,150 mm × 695 mm × 990 mm (45 1/4" × 27 3/8" × 39")
*1 Within 10 minutes after the last print job
2
*2 When using plain paper and recycled paper (85 g/m (23-lb bond)), and density setting 3 (Standard)
Chart used: Print measurement pattern [Color measurement sample 2 (JEITA standard pattern J6)]
*3 The margin when printing envelopes is 10 mm (3/8").
The guaranteed area when printing images is the area enclosed within 3 mm (1/8") of the edges of the paper.
*4
*5
*6
*7
When using plain paper and recycled paper (85 g/m2 (23-lb bond))
When not printing
One gigabyte (GB) is calculated as 1 billion bytes.
The continuous print speed varies depending on the type of optional output equipment connected.
Multifunction finisher: Max. 110 sheets/minute (A4-R Simplex)
Face down offset tray: Max. 120 sheets/minute (A4-R Simplex)
ComColor Series Safety Information 01
16
■ ComColor 7050/7050R/3050/3050R Specifications
Basic Functions and Print Functions
Model
ComColor 7050/7050R:SE-M301
ComColor 3050/3050R:SE-M401
Type
Console
Color Support
Full color
Print Type
Line-type inkjet system
Ink Type
Oil-based pigment ink (Cyan, Magenta, Yellow, Black)
Standard: 300 dpi (main scanning direction) × 300 dpi (sub-scanning direction)
Resolution
Fine: 300 dpi (main scanning direction) × 600 dpi (sub-scanning direction)
Number of Gray Levels
For each CMYK color (8 gray levels)
Data Processing Resolution
Standard: 300 dpi × 300 dpi
Fine: 300 dpi × 600 dpi
Line smoothing: 600 dpi × 600 dpi
Warm-up Time
2 min. 45 sec. or less (at room temperature of 20ºC (68ºF))
Monochrome: 8 sec or less*1 (when copying A4-R/Letter-R
orientation using monochrome mode)
First Print Time
Continuous Print Speed*2*7
Color: 8 sec or less*1 (when copying A4-R/Letter-R orientation using
color mode)
A4-R/Letter-R
Simplex: 120 ppm
Duplex: 60 sheets/minute (120 ppm)
A4/Letter
Simplex: 90 ppm
Duplex: 45 sheets/minute (90 ppm)
B4/Legal
Simplex: 76 ppm
Duplex: 38 sheets/minute (76 ppm)
A3/Ledger
Simplex: 66 ppm
Duplex: 33 sheets/minute (66 ppm)
Duplex Printing
Standard
Standard Tray
Maximum: 340 mm × 550 mm (13 3/8" × 21 5/8")
Minimum: 90 mm × 148 mm (3 9/16" × 5 13/16")
Feed Tray
Maximum: 297 mm × 420 mm (11 11/16" × 17")
Minimum: 182 mm × 182 mm (7 3/16" × 7 3/16")
Paper Size
Printable Area
ComColor 7050/7050R:
Maximum: 314 mm × 548 mm (12 3/8" × 21 9/16")
ComColor 3050/3050R:
Maximum: 210 mm × 544 mm (8 1/4" × 21 7/16")
Guaranteed Print Area*3
ComColor 7050/7050R:
Standard: Margin width of 3 mm (1/8")
Maximum: Margin width of 1 mm (0.04")
ComColor 3050/3050R:
Standard: Margin width of 5 mm (3/16")
Maximum: Margin width of 3 mm (1/8")
Paper Weight
Paper Feed Method/Paper
*4
Tray Capacity
Standard Tray
46 g/m2 (12-lb bond) to 210 g/m2 (56-lb bond) (plain paper)
Feed Tray
52 g/m2 (14-lb bond) to 104 g/m2 (28-lb bond) (plain paper)
Standard Tray
1,000 sheets (Height up to 110 mm (4 5/16"))
Feed Tray
500 sheets × 3 trays (Height up to 50 mm (1 15/16"))
Continuous Printing Capacity
Output Tray Capacity*4
17
9,999 sheets
Standard
500 sheets (Height up to 60 mm (2 3/8"))
Option
1,000 sheets (when using the optional auto-control stacking tray or
wide stacking tray)
Page Description Language
Original PDL
Supported Protocols
TCP/IP, HTTP, HTTPs (SSL), DHCP, ftp, lpr, IPP, SNMP,
Port 9100 (RAW port)
ComColor Series Safety Information 01
Microsoft® Windows® 2000
Microsoft® Windows® XP (32-bit version)
Supported Operating Systems
Microsoft® Windows Server 2003 (32-bit version)
Microsoft® Windows 2000 Server
Microsoft® Windows Vista® (32-bit version)
Installed Fonts
None
Emulation
None
Network Interface
Ethernet 1000BASE-T, 100BASE-TX, 10BASE-T (2ch)
CPU
Intel® Celeron®-M440 (1.86 GHz)
Memory Capacity
512 MB
Hard Disk*6
Capacity
160 GB
Available Space
140 GB
Operating System
Linux
Power Source
AC 100-240 V, 10-5 A, 50-60 Hz
Max. 1,000 W
Power Consumption
Ready*5: 250 W
Sleep: Max. 45 W
Stand-by: Max. 1 W
Operating Noise
Max. 68 dB (when printing)
Operating Environment
Temperature: 15ºC to 30ºC (59ºF to 86ºF)
Humidity: 40% to 70% RH (non-condensing)
Dimensions (W × D × H)
In use:1,210 mm × 695 mm × 1,020 mm
(47 5/8" × 27 3/8" × 40 3/16")
Weight
180 kg (397 lb)
Required Space (W × D × H)
With front cover and feed tray extended:
1,210 mm × 1,230 mm × 1,020 mm (47 5/8" × 48 7/16" × 40 3/16")
With face down tray and standard tray stored:
1,150 mm × 695 mm × 990 mm (45 1/4" × 27 3/8" × 39")
*1 Within 10 minutes after the last print job
2
*2 When using plain paper and recycled paper (85 g/m (23-lb bond)), and density setting 3 (Standard)
Chart used: Print measurement pattern [Color measurement sample 2 (JEITA standard pattern J6)]
*3 The margin when printing envelopes is 10 mm (3/8").
For ComColor 7050/7050R, the guaranteed area when printing images is the area enclosed within 3 mm (1/8") of the edges of the
paper.
For ComColor 3050/3050R, the guaranteed area when printing images is the area enclosed within 5 mm (3/16") of the edges of the
paper.
*4
*5
*6
*7
When using plain paper and recycled paper (85 g/m2 (23-lb bond))
When not printing
One gigabyte (GB) is calculated as 1 billion bytes.
The continuous print speed varies depending on the type of optional output equipment connected.
Multifunction finisher: Max. 110 sheets/minute (A4-R Simplex)
Face down offset tray: Max. 110 sheets/minute (A4-R Simplex)
ComColor Series Safety Information 01
18
■ ComColor 7010/7010R/3010/3010R Specifications
Basic Functions and Print Functions
Model
ComColor 7010/7010R:SE-L301
ComColor 3010/3010R:SE-L401
Type
Console
Color Support
Full color
Print Type
Line-type inkjet system
Ink Type
Oil-based pigment ink (Cyan, Magenta, Yellow, Black)
Standard: 300 dpi (main scanning direction) × 300 dpi (sub-scanning direction)
Resolution
Fine: 300 dpi (main scanning direction) × 600 dpi (sub-scanning direction)
Number of Gray Levels
For each CMYK color (8 gray levels)
Data Processing Resolution
Standard: 300 dpi × 300 dpi
Fine: 300 dpi × 600 dpi
Line smoothing: 600 dpi × 600 dpi
Warm-up Time
2 min. 45 sec. or less (at room temperature of 20ºC (68ºF))
Monochrome: 8 sec or less*1 (when copying A4-R/Letter-R
orientation using monochrome mode)
First Print Time
Continuous Print Speed*2*7
Color: 8 sec or less*1 (when copying A4-R/Letter-R orientation using
color mode)
A4-R/Letter-R
Simplex: 120 ppm
Duplex: 60 sheets/minute (120 ppm)
A4/Letter
Simplex: 90 ppm
Duplex: 45 sheets/minute (90 ppm)
B4/Legal
Simplex: 76 ppm
Duplex: 38 sheets/minute (76 ppm)
A3/Ledger
Simplex: 66 ppm
Duplex: 33 sheets/minute (66 ppm)
Duplex Printing
Standard
Paper Size
Maximum: 340 mm × 550 mm (13 3/8" × 21 5/8")
Minimum: 90 mm × 148 mm (3 9/16" × 5 13/16")
Printable Area
ComColor 7010/7010R
Maximum: 310 mm × 544 mm (12 3/16" × 21 7/16")
ComColor 3010/3010R
Maximum: 210 mm × 544 mm (8 1/4" × 21 7/16")
Guaranteed Print Area*3
Standard: Margin width of 5 mm (3/16")
Maximum: Margin width of 3 mm (1/8")
Paper Weight
46 g/m2 (12-lb bond) to 210 g/m2 (56-lb bond) (plain paper)
Paper Feed Method/Paper Tray Capacity*4
1,000 sheets (Height up to 110 mm (4 5/16"))
Continuous Printing Capacity
9,999 sheets
Output Tray Capacity*4
Standard
500 sheets (Height up to 60 mm (2 3/8"))
Option
1,000 sheets (when using the optional auto-control stacking tray or
wide stacking tray)
Page Description Language
Original PDL
Supported Protocols
TCP/IP, HTTP, HTTPs (SSL), DHCP, ftp, lpr, IPP, SNMP,
Port 9100 (RAW port)
Microsoft® Windows® 2000
Microsoft® Windows® XP (32-bit version)
Supported Operating Systems
Microsoft® Windows Server 2003 (32-bit version)
Microsoft® Windows 2000 Server
Microsoft® Windows Vista® (32-bit version)
19
Installed Fonts
None
Emulation
None
Network Interface
Ethernet 1000BASE-T, 100BASE-TX, 10BASE-T (2ch)
CPU
Intel® Celeron®-M440 (1.86 GHz)
Memory Capacity
512 MB
ComColor Series Safety Information 01
Hard Disk*6
Capacity
160 GB
Available Space
140 GB
Operating System
Linux
Power Source
AC 100-240 V, 10-5 A, 50-60 Hz
Max. 1,000 W
Power Consumption
Ready*5: 250 W
Sleep: Max. 45 W
Stand-by: Max. 1 W
Operating Noise
Max. 68 dB (when printing)
Operating Environment
Temperature: 15ºC to 30ºC (59ºF to 86ºF)
Humidity: 40% to 70% RH (non-condensing)
Dimensions (W × D × H)
In use: 1,210 mm × 695 mm × 1,020 mm
(47 5/8" × 27 3/8" × 40 3/16")
Weight
160 kg (353 lb)
Required Space (W × D × H)
With front cover extended:
1,210 mm × 1,230 mm × 1,020 mm (47 5/8" × 48 7/16" × 40 3/16")
With face down tray and standard tray stored:
1,150 mm × 695 mm × 990 mm (45 1/4" × 27 3/8" × 39")
*1 Within 10 minutes after the last print job
2
*2 When using plain paper and recycled paper (85 g/m (23-lb bond)), and density setting 3 (Standard)
Chart used: Print measurement pattern [Color measurement sample 2 (JEITA standard pattern J6)]
*3 The margin when printing envelopes is 10 mm (3/8").
The guaranteed area when printing images is the area enclosed within 5 mm (3/16") of the edges of the paper.
*4
*5
*6
*7
When using plain paper and recycled paper (85 g/m2 (23-lb bond))
When not printing
One gigabyte (GB) is calculated as 1 billion bytes.
The continuous print speed varies depending on the type of optional output equipment connected.
Face down offset tray: Max. 110 sheets/minute (A4-R Simplex)
ComColor Series Safety Information 01
20
■ Scanner HS4000 (Optional)
Copy/Scan Functions
Type
Flat Bed Scanner with Automatic Document Feeder (ADF)
Scanning modes
Color, Monochrome, Auto
Scanning resolution
600 dpi, 400 dpi, 300 dpi, or 200 dpi
Maximum scanning area
303 mm × 432 mm (11 15/16" × 17") (when using platen glass)
295 mm × 430 mm (11 5/8" × 16 15/16") (when using ADF)
Writing resolution
Standard: 300 dpi × 300 dpi
Fine: 300 dpi × 600 dpi
Copy paper size
Maximum: 303 mm × 432 mm (11 15/16" × 17") (equivalent to A3)
Initial copy time
Monochrome/Color: 11.5 sec or less (when copying A4-R/Letter-R
orientation using Color Priority Mode)
Scanning speed
Simplex copying (A4-R/Letter-R, using ADF): 40 ppm or higher
Duplex copying (A4-R/Letter-R, using ADF): 9 sheets/minute
(18 ppm) or higher
Reproduction size
50% to 200% (Copy mode)
50% to 200% (Scanner mode, resolution: 200/300 dpi), only 100%
(Scanner mode, resolution: 400/600 dpi)
Type
Original source displacement (capable of duplex scanning by switch-back)
Original source size
Maximum: 297 mm × 432 mm (11 11/16" × 17") (equivalent to A3)
Minimum: 100 mm × 148 mm (3 15/16" × 5 13/16")
Paper quality
52 g/m2 (14-lb bond) to 128 g/m2 (34-lb bond)
Original source capacity
Smaller than B4 size
80 g/m2 (21-lb bond) or less: Max. 100 sheets
More than 80 g/m2 (21-lb bond): Height up to 15 mm (5/8")
Original source capacity
B4 size or larger
80 g/m2 (21-lb bond) or less: Max. 60 sheets
More than 80 g/m2 (21-lb bond): Height up to 9 mm (3/8")
Original source
exchange speed
Simplex printing: 40 ppm or higher (A4-R/Letter-R)
Duplex printing: 9 sheets/minute (18 ppm) or higher (A4-R/Letter-R)
Scanning gray levels
10-bit input and 8-bit output for each RGB color
Original source scanning
speed
Monochrome/Color: 40 ppm
∗ RISO KAGAKU standard original (A4-R/Letter-R), 200 dpi, when
stored to main unit hard drive
Network Interface*
Ethernet 1000BASE-T/100BASE-TX/10BASE-T
Data-saving method*
Save to main unit hard drive, server, or USB flash drive, or send by e-mail
Data-saving format*
Monochrome: TIFF, PDF
Grayscale/Full Color: TIFF, JPEG, PDF
Copy functions
ADF
Scan functions
Power source
AC 100-127/200-240 V, 50/60 Hz
Power consumption
Max. 120 W
Dimensions
642 mm × 551 mm × 248 mm (25 1/4" × 21 11/16" × 9 3/4")
Weight
Approx. 28 kg (62 lb)
Dimensions (when connected to main unit)
(W × D × H)
In use: 1,220 mm × 800 mm × 1,220 mm (48" × 31 1/2" × 48")
With cover and tray extended:
1,220 mm × 1,335 mm × 1,610 mm (48" × 52 9/16" × 63 3/8")
* Via the internal host controller
21
ComColor Series Safety Information 01
■ Multifunction Finisher (Optional)
Tray Type
Top Tray
Collating, stacking
Stacking Tray
Collating, stacking (offset)
Booklet Tray
Booklet, Paper folding
Top Tray*1
Maximum: 330 mm × 488 mm (13" × 19 3/16")
Minimum: 100 mm × 148 mm (3 15/16" × 5 13/16")
Stacking Tray*1
Maximum: 330 mm × 488 mm (13" × 19 3/16")
Minimum: 182 mm × 182 mm (7 3/16" × 7 3/16")
Stapling
Maximum: 297 mm × 432 mm (11 11/16" × 17") (equivalent to A3)
Minimum: 203 mm × 182 mm (8" × 7 3/16")
Booklet Tray*1
Maximum: 330 mm × 457 mm (13" × 18")
Minimum: 210 mm × 280 mm (8 1/4" × 11")
Top Tray
52 g/m2 (14-lb bond) to 210 g/m2 (56-lb bond)
Stacking Tray
52 g/m2 (14-lb bond) to 210 g/m2 (56-lb bond)
Booklet Tray
60 g/m2 (16-lb bond) to 90 g/m2 (24-lb bond) (cover: 210 g/m2 (56-lb
bond))
Top Tray
500 sheets
Stacking Tray*3
2,000 sheets (200 copies)
Booklet Tray
20 copies
Paper Size
Paper Weight
Tray Capacity
Maximum Number of
Staples*2*4
Stapling
Staple Paper Size
100 sheets
Maximum: 297 mm × 432 mm (11 11/16" × 17") (equivalent to A3)
Minimum: 203 mm × 182 mm (8" × 7 3/16") (equivalent to B5-R)
1 at front side (angle stapling),
Staple Position
Punching
Creating a Booklet
(Center margin/2-fold)
1 at rear side (angle stapling*5, parallel stapling), 2 at center (parallel
stapling)
Number of Punches
2 holes, 3 holes
2 holes, 4 holes
Applicable Sizes
2 holes: A3, B4, A4-R, A4, B5-R , Ledger, Legal, Letter, Letter-R
3 holes: A3, B4, A4-R, B5-R, Ledger, Letter-R
4 holes: A3, A4-R, Ledger, Letter-R
Paper Weight
52 g/m2 (14-lb bond) to 200 g/m2 (53-lb bond)
Maximum Number of
Center margin: 15 sheets (60 pages)
2-fold: 5 sheets (20 pages)
Sheets*2*6
Operating Environment
Temperature: 15ºC to 35ºC (59ºF to 95ºF)
Humidity: 40% to 70% RH (non-condensing)
Dimensions (W × D × H)
1,100 mm × 760 mm × 1,165 mm (43 5/16" × 29 15/16" × 45 7/8")
Weight
131 kg (289 lbs)
Power Source
AC 100-120/200-240 V, 50/60 Hz, 2.0/1.0 A or more
Power Consumption
Max. 175 W
Operating Noise (when using finisher)
Max. 68 dB
Dimensions (when Connected to main unit)
(W × D × H)
In use: 2,295 mm × 760 mm × 1,165 mm (90 3/16" × 29 15/16" × 45 7/8")
With cover, and tray extended:
2,295 mm × 1,275 mm × 1,165 mm (90 3/8" × 50 3/16" × 45 7/8")
*1 When color printing on paper that is longer than 432 mm (17"), the image printed beyond 432 mm (17") may be distorted.
2
*2 When using plain paper and recycled paper (85 g/m (23-lb bond))
2
*3 When using plain paper and recycled paper (85 g/m (23-lb bound)) with A4 or B5-R orientation
When using paper sizes other than A4 or B5-R, the capacity is 1,500 sheets (100 copies)
*4 65 sheets for a paper size exceeding A4/Letter
*5 Rear-side angle stapling is only available for A4-R and A3.
*6 Includes an added cover.
ComColor Series Safety Information 01
22
■ IC Card Authentication Kit (Optional)
Applicable Card
ISO 14443 TypeA/TypeC (FeliCa®/Mifare®)
Radio Law Category
Guided read-write communication equipment
Power Source
Power received from USB port
Operating Environment
Temperature: 15ºC to 30ºC (59ºF to 86ºF)
Humidity: 40% to 70% RH (non-condensing)
Dimensions (W × D × H)
92 mm × 64 mm × 16 mm (3 5/8" × 2 1/2" × 5/8") (excluding protruding parts)
Weight
90 g (3 oz)
Notice for European Union Member States
RISO, the environment and the Waste Electrical and Electronic Equipment Directive "WEEE Directive"
What is the WEEE Directive?
The purpose of the WEEE Directive is to reduce waste and ensure Electrical and Electronic Equipment is recycled at the
end of its useful life.
What does the crossed out wheeled bin symbol mean?
The crossed out wheeled bin symbol indicates this product must be disposed of separately to normal waste.
Please contact your RISO service agent for information about disposal.
What does the solid bar symbol mean?
The solid bar under the crossed out wheeled bin indicates this product was put on the market after the 13th August 2005.
Who should I contact if I want more information about the WEEE Directive?
You should contact your local RISO service agent for more information.
Trademark Credits
Microsoft and Windows are registered trademarks of Microsoft Corporation in the U.S. and/or other countries.
ColorSet is a trademark of Monotype Imaging Inc. registered in the U.S. Patent & Trademark Office and may be registered
in certain jurisdictions.
Intel and Celeron are trademarks of Intel Corporation in the United States and other countries.
FeliCa is a registered trademark of Sony Corporation.
Mifare is a registered trademark of Royal Philips Electronics.
ComColor and FORCEJET are trademarks of RISO KAGAKU CORPORATION.
is a registered trademark of RISO KAGAKU CORPORATION in Japan and other countries.
All other product names and company names written in this guide are trademarks or registered trademarks of their
respective companies.
23
ComColor Series Safety Information 01
ComColor Series Safety Information 01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising