W9-MLTF _IM
W9 Series
Fixed & Tilt Flat Screen Mounts
Medium/Large
W9-MT/W9-LT
W9-MF/W9-LF
or brick wall.
CAUTION:The maximum loading weight is 100lbs /150lbs, Use heavier than that may cause injury see apparatus instructions.
Este producto ha sido diseñado para su uso en una pared vertical interpretarse de albañilería (cemento sólido) o vigas de madera o pared de ladrillo. Los postes de madera deben
tener un mínimo de 2x4 pulgadas.Para una instalación segura en la pared se va a instalar debe ser compatible con 4 veces el peso de la carga total, si no, la superficie debe ser
reforzada para cumplir con esta norma.
PRECAUCIÓN: El peso máximo de carga es £ 100/ £ 150, más pesado que el uso que pueden causar lesiones vea las instrucciones de un aparato.
Ce produit a été conçu pour une utilisation sur un mur vertical interprété de maçonnerie (béton plein) ou des poteaux en bois ou en brique du mur. Poteaux en bois doivent être
d'un minimum de 2x4 pouces.Pour une installation sûre au mur vous montez doit prendre en charge quatre fois le poids de la charge totale, sinon, la surface doit être renforcée
pour répondre à cette norme.
ATTENTION: Le poids de chargement maximal est de £ 100 / £ 150, plus lourd que l'utilisation qui peut causer des blessures voir les instructions appareil.
Dieses Produkt wurde für den Einsatz an einer senkrechten Wand aus Mauerwerk (festen Beton) oder Holzständer-oder Ziegelwand ausgelegt konzipiert. Holzpfosten muss
mindestens 2x4 Zoll.Für eine sichere Installation der Wand sind Sie Montage an muss der 4-fachen Gewicht der gesamten Last tragen, wenn nicht, muss die Oberfläche verstärkt,
um diesen Standard zu erfüllen.
ACHTUNG: Die maximale Ladegewicht ist 100lbs /150lbs, Verwendung schwerer als die Verletzungen verursachen können sehen Apparat Anweisungen.
*Recommended use with Wood Stud & Concrete Wall
W9-MF/W9-MT
42”
45 kg
100 lbs
W9-LF/W9-LT
63”
68 kg
150 lbs
Drill
Socket Wrench
Philips Screwdriver
Pencil
Hammer
Stud Finder
W9-MT/W9-LT
W9-MF/W9-LF
B
W9-MF/W9-LF/W9-MT/W9-LT
Wall Bracket X1
C
W9-MF/W9-LF/W9-MT/W9-LT
Safety Latch Rod X1
A
A
Flat Screen Fixed Bracket X2
Flat Screen Tilt Bracket X2
W9-MF/W9-LF
W9-MT/W9-LT
Lag Bolts ST6.3x50mm
Wall Anchors
W9-MF / W9-MT
2
2
W9-LF / W9-LT
3
3
M4x15mm
Screws
M4x35mm
Screws
M5x15mm
Screws
M5x35mm
Screws
M6x15mm
Screws
M6x35mm
Screws
M8x15mm
Screws
M8x35mm
Screws
Round
Spacers
3/4”
Round
Washers
Wall Bracket Installation Steps for Wood Studs
Locate studs with stud finder. Mark stud
edge and center location with pencil.
Select desired height. Use Wall Bracket as template to
mark drilling locations with pencil.
Use level to ensure proper alignment.
Stud
Stud
W9-MF / W9-MT drill pilot holes X2
W9-LF / W9-LT mark drilling locations X3
Drill pilot holes at marked locations.
Secure Wall Bracket with Screws and Washers .
Stud
Stud
Socket Wrench
Drill
W9-MF / W9-MT drill pilot holes X2
W9-LF / W9-LT drill pilot holes X3
Pilot Hole Size
1/8”(3 mm)
Pilot Hole Depth 2 3/4”(70 mm)
W9-MF / W9-MT secure screws and washers X2
W9-LF / W9-LT secure screws and washers X3
Wall Bracket Installation Steps for Concrete
Select desired height. Use Wall Bracket as template
to mark drilling locations with pencil.
Use level to ensure proper alignment.
Drill pilot holes at marked locations.
Drill
W9-MF / W9-MT drill pilot holes X2
W9-LF / W9-LT drill pilot holes X3
W9-MF / W9-MT mark drilling locations X2
Pilot Hole Size
W9-LF / W9-LT mark drilling locations X3
3/8”(10 mm)
Pilot Hole Depth 2 3/4”(70 mm)
Use a socket wrench to tighten screws
with washers to fix the wall plate on the wall.
Gently hammer Wall Anchors into
pilot holes.
Socket Wrench
X
W9-MF / W9-MT wall anchors X2
W9-MF / W9-MT secure screws and washers X2
W9-LF / W9-LT wall anchors X3
W9-LF / W9-LT secure screws and washers X3
Flat Screen Bracket Attachment Steps
Align Flat Screen Bracket with VESA hole pattern on back of Flat Screen.
Secure with appropriate screw size and washers from Monitor Kit as illustrated.
Be sure to carefully align the holes of the brackets with the mounting holes on the flat screen
Proper Screws
from Monitor Kit
Spacers M-I
Optional
Round Washers M-J
Options
Need Spacers M-I
No need Spacers M-I
Lift and hook flat screen with attached brackets (A) to the wall bracket (B).
Assistance may be the required to lift your flat screen into position.
Adjust flat screen angle with Tool-Free Tilt Adjustment Lever.
Turn counter-clockwise to loosen and adjust, then clockwise to tighten and lock into place.
Align Safety Latch Rod (C), with holes in Wall Bracket (B)
and Flat Screen Brackets (A). Slide rod completely in and turn clockwise to secure
bracket into place.
Use Tool-Free Adjustment lever to tilt and lock Flat Screen into place.
-3 ~10
a.
b.
a.Turn lever counter
clockwise to adjust angle.
b.Select desired angle,
turn lever clockwise to
secure into place.
6
THANK YOU FOR PURCHASING ATHLETIC PRODUCTS.
GRACIAS POR ADQUIRIR UN PRODUCTO ATHLETIC
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising