measuring apparatus

MEASURING APPARATUS
LANGLOIS
info@langlois-france.com I www.langlois-france.com
Phone: 0033 5 56 75 13 33
Probes
DIFFERENTIALS PROBES
OSCILLOSCOPE
Mains adapter
supplied
Y1
Y2
MAINS
RÉSEAU
+7V max
-
M
SONDES
DIFFERENTIAL
DIFFERENTIELLES
PROBES
Safety connectors
COMPACT
DIFFERENTIALS PROBES
type ISOL
ISOL-710
Ergonomic solutions of differential probes,
supplied from mains, with 2 or 4 channels
according the models. The housing is strong
enough to put an oscilloscope on top.
ref. ISOL712 - ISOL 724
Complete datasheet
www.langlois-france.com
REF.
Channel
DP25
These probes are used for displaying and measuring of dangerous voltages with a Class I oscilloscope, in accordance with the
user safety standards. In fact, the image voltage applied to the
oscilloscope is no more than a few volts. On the other hand, by
using two probes the voltages applied to the oscilloscope inputs
are isolated from one another. So, differential probes can
measure high voltages and/or voltages which relate to different
potentials, without any risk of short-circuiting through the base
of the oscilloscope.
Measurable input voltage DC + AC
ISOL-720
DP25
1
1
1
DC to 25MHz
1/10 and 1/100
1/20 and 1/200
1/20 1/50 1/200
140Vpp on 1/10
1400Vpp on 1/100
280Vpp on 1/20
2000Vpp on 1/200
respect. 200Vpp / 500Vpp / 1400Vpp
Output voltage to oscilloscope
+/- 7V
Max. differential input voltage
Max common mode voltage (1)
Input impedance
+/- 5V
1000Vrms
500Vrms
1000Vrms
4 MΩ / 5pF
600Vrms
4 MΩ / 1,2pF
Rise time
14 ns
Accuracy
2%
CEI1010 cat III Pol 2
ref. ADA6
ISOL-710
Bandwidth to -3dB
Attenuation ratio
OPTIONS
Mains adapter for ISOL probes
1000Vrms
600Vrms
Battery (4 x LR6) and mains adapter
Mains adapter 230V 50/60Hz
Dimensions / Weight
158 x 62 x 20mm / 290g
210 x 58 x 35mm / 200g
Supplied accessories
Rubber jacket
+ test clip
Holster + test clips
+ mains adapter
Power source
(1) Common mode voltage: voltage between, on one hand, the interconnected inputs and on the other hand the ground or the BNC terminal on the oscilloscope
188
PRODUCTS 2 YEARS GUARANTEE
Measuring apparatus
TRUE RMS DC AND AC LOW CURRENT PROBES
Ø21
Ø8
VA15
Ø9
Ø9
DCA60
PSY500
PSY510
These probes are used with an oscilloscope, a multimeter or a recording instrument. They deliver a secondary image voltage of the primary current (a few dozen millivolts),
thereby allowing the user to take measurements in complete safety and without having to switch off the power to the circuit. The Hall sensor fitted in them can detect a DC component overlaid onto the AC component. When used with a true RMS multimeter, these probes will provide a true RMS current measurement.
REF.
VA15
DCA60
PSY500
PSY510
Output voltage /
Input current
100mV/A range 4A / 10mV/A range 30A
1000mV/A range 400mA AC only.
100mV/A range 20A
10mV/A range 60A
200mV/A range 5A
20mV/A range 50A
1 V / A range 4A
0,1V / A range 40A
Ranges DC + AC
4A & 30A
20A & 60A
5A & 50A
4 & 40 A
Range AC only
400mA AC
Accuracy
Diameter
of the jaws
Power source
2% DC to 80Hz
3% 80Hz to 180kHz
5% 180kHz to 270kHz
6% 270kHz to 350khz
1% DC ~ 1kHz
2% 40Hz ~ 2kHz
4% 2kHz ~ 10kHz
6% 10kHz ~ 40kHz
21mm
8mm
9mm
battery : 2 x LR6
battery : 1 x 6LR61
Mains or battery 1LR61 (9V)
CEI100
2% DC ~ 50Hz
3% 50Hz ~ 100kHz
5% 100kHz ~ 120kHz
CATIII 300Veff pol2
2 safety leads
1 BNC adapter
1 BNC adapter
1 BNC lead
1 BNC adapter
1 mains adapter
1 BNC lead
1 BNC adapter
1 mains adapter
Supplied with
PRODUCTS 2 YEARS GUARANTEE
189
Oscilloscopes
DIGITAL STORAGE OSCILLOSCOPES 70 TO 150MHZ
• Color screen TFT LCD - backlight - Vision 45 ° - 234 x 320 points
• save/recall: 15 waveforms and 15 setups
• GO – NO GO functions
• ΔV ΔT ΔF cursors
• Data logger
• Assistant for test probes x0.1 to x2000
• HELP key
• Multilangage
USB
Complete datasheet
www.langlois-france.com
Labview
Driver
PC
software
Série GDS1000A-U
REF.
GDS1072A-U
Channels
Bandwidth -3dB
Rise time
GDS1102A-U
GDS1152A-U
2
2
2
70MHz
100MHz
150MHz
5ns
3,5ns
2,3ns
Sampling rate
1GSa/s real time, 25GSa/s equivalent time
DIGITAL STORAGE OSCILLOSCOPES 70 TO 300MHZ
OPTIONS
Logic analyser
ref. DS2-16LA 16 channels
ref. DS2-8LA 8 channels
ref. DS2-GPIB
GDS2000A serie
USB
PC
full speed
software
Labview
Driver
PictBridge
GPIB
(option)
Ethernet
(option)
LAN
(option)
VGA
(option)
RS-232
Complete datasheet
www.langlois-france.com
REF.
Channels
Bandwidth -3dB
Rise time
Sampling rate
190
• Colour screen 20cm TFT high resolution (800 x 600 points)
• Save/recall: 24 waveforms and 20 setups
• Fast update rate of 80,000 waveform per second
• Curve plotting: points, vectors, variable persistence
• Acquisition by segments at your choice (2048 possible observations)
• Search function of the wave form by criteria in the entire memory. Zoom.
• XY mode : 2 simultaneous displays
• 6 digits frequencymeter
• 8 or 16 logic inputs (option)
• 8 or 16 additional chanels, either 12 or 20 with time chanels (option)
• HELP touch / Multilangage
GDS2072A
GDS2102A
GDS2202A
GDS2302A
GDS2074A
GDS2104A
GDS2204A
GDS2304A
2
2
2
2
4
4
4
4
70MHz
100MHz
200MHz
300MHz
70MHz
100MHz
200MHz
300MHz
5ns
3,5ns
1,75ns
1,17ns
5ns
3,5ns
1,75ns
1,17ns
2GSa/s real time, 100GSa/s equivalent time
PRODUCTS 2 YEARS GUARANTEE
Measuring apparatus
20 TO 200MHZ HAND-HELD OSCILLOSCOPE MULTIMETER
Complete datasheet
www.langlois-france.com
GDS200 / 300 serie
USB
Labview
Driver
Ref. 1022MN / 2062MN
PC
RS-232
software
• 7” touchscreen (480x800) with landscape and portrait rotation
• 3 versions: 70MHz, 100MHz and 200MHz
with 2 memory depths: 1 Mpoints or 5 Mpoints
• Data recording on USB key
• Internal battery for use in laboratory as well as in the field
• Multimeter functions
REF.
GDS207
GDS210
• Colour screen 75 x 56mm, 640 x 480 points
• Save/Recall 4 waveforms & 4 setup
• Zoom on the window. Choise of the window and zoom as far as 5ns/div
• Autoset and Autoranges, auto. measurements, cursors
• Digital multimeter TRMS
GDS220
Display
Channels
Bandwidth -3dB
Rise time
USB
GDS307
GDS310
GDS320
1022MN
Tactile 7’’
2062MN
3,7’’’’ (75 x 56mm)
2
2
2
2
2
2
2
2
70MHz
100MHz
200MHz
70MHz
100MHz
200MHz
20MHz
60MHz
<5ns
<3.5ns
<1.75ns
<5ns
<3.5ns
<1.75ns
17,5ns
5,8ns
100Ma/s
250Ma/s
Sampling rate
1GSa/s
4-CHANNEL PC OSCILLOSCOPE
Simple and
convivial
setup menu
ref. PC-SCOPE
Complete datasheet
www.langlois-france.com
• Software included
• USB (2.0) port for real-time data transmission
• LAN port for remote access via network
• 20 automatic measurement modes
• Input voltage from 40V to 400V / Bandwith: 60MHz
• Sample rate per channel: 500MSa/s
Behaves like
a digital
oscilloscope
4CH
LAN
USB
Remote
Control
FFT
function
4-channel oscilloscope to connect to a desktop or laptop computer. It’s equipped with an USB
(2.0) port for real-time data transmission. You can evaluate and analyze data in real time
on the computer thanks to the software included. For this, you have 20 measurement modes
available and also several mathematical functions. Its LAN port enables the device to be
installed in electrical systems or control cabinets. Measured data viewing by remote access
through the network.
PRODUCTS 2 YEARS GUARANTEE
191
Generators
FUNCTION GENERATORS 2 & 3MHZ WITH OR WITHOUT FREQUENCY COUNTER
GFG8219 - 3MHz - AM - FM
GFG8216 - 3MHz
GFG8215 - 3MHz
Complete datasheet
www.langlois-france.com
SFG1013 - 3MHz - DDS
GFG8015G - 2,2MHz
REF.
GFG8219
GFG8216
GFG8215
SFG1013
GFG8015G
sine - sqare - triangle - pulse - rampes - TTL
CMOS (GFG8215 - GFG8216 - GFG8219 only) - AM - FM (GFG8219 only)
Waveforms
0,01Hz to 3,3 MHz - 7 ranges
SFG1013 only : Voltage display
Frequency
Output voltage
0,01Hz to 2,2 MHz
7 ranges
20 Vpp on 600Ω 10Vpp on 50Ω
Attenuators
2 : -20dB ±1dB
1 : -40dB
1 : -20dB ±1dB
Offset
Continuously variable from -10V to +10V into 600Ω
Duty
variable from 20% to 80%
variable from 25% to 75%
Calibrate to 50%
Calibrate to 50%
variable from 20% to 80%
variable from 20% to 80%
variable from 10% to 90%
Calibrate to 50%
Adjustable duty without
Calibrate to 50%
Adjustable duty without
Calibrate to 50%
frequency variation
frequency variation
≥ 3Vpp . Rise time ≤25ns. Load : 20 TTL gates
TTL output
CMOS output
Adjust 4Vcc to 14,5Vpp. Rise time < 120ns
no
ARBITRARY FUNCTION GENERATORS 5 TO 25MHZ
USB
PC
software
REF.
Frequency range
Waveforms
192
• Color LCD display 3,5’’.
• Frequency + voltage and settings.
• Programming of an arbitrary signal with the keyboard.
• Sample rate 20MSa/s and 10 bits amplitude resolution.
• 4000 points memory.
• 1% to 99% adjustable duty cycle for square waveform
• Frequency and (Vpp, Vrms, dBm) offset voltage display and configuration on 3.5’’ LCD Screen
• USB device interface for remote control and waveform editing. Software provided.
• 10 groups of setting memories
• AM/FM/FSK Modulation and Sweep (AFG-2100 only)
• Frequency counter (AFG-2100 only)
Labview
Driver
AFG2105
AFG2112
AFG2125
AFG2005
AFG2012
AFG2025
0,1Hz to 5MHz
0,1Hz to 12MHz
0,1Hz to 25MHz
0,1Hz to 5MHz
0,1Hz to 12MHz
0,1Hz to 25MHz
Sine, square, Triangle, Ramp, Noise, Arbitrary waveform
PRODUCTS 2 YEARS GUARANTEE
¨Power supplies
Measuring apparatus
MULTI-OUTPUTS POWER SUPPLIES
Complete range of DC or AC&DC power supplies, fixed or variable, fully protected for various type of use in laboratory.
ALF1501D
Ref.
AL841C
ALF1501D
AL843A
AL843A
AM061205
DC OUTPUTS
AC OUTPUTS
Power
Informations
3V / 4,5V / 6V / 7,5V / 9V / 12V - 1A
-
12 W
6 selectable voltage
±15V 1A or 24V 1 A or 12V 2,5A
-
30 W
±15V (Aj. ±10 à ±15V)
6V, 12V / 10A or 24V / 5A
6V, 12V / 10A or 24V / 5A
120 W
AC & DC simultaneous
AM061205
6V , 12V / 5A
6V , 12V / 5A
120 W
AC & DC simultaneous
AM061210
6V / 20A , 12V / 10A
6V / 20A , 12V / 10A
120 W
AC & DC simultaneous
640W – 0-32V – 0-20A PROGRAMMABLE POWER SUPPLY
• 0V – 32V
• 0A – 20A
• 640W
• Programmable
• Visual: Large graphic display
• Soft-touch: sensitive keypad
• Connected: USB, RS232, RS485 and 0-10V isolated
• Performance: output in the rear-panel, used for remote-sensing
• Elegant: New design
• Space-saving: vertical and compact box
• Practical: lightweight with built-in handle and cord storage area
• Quiet: Silent temperature-controlled fan cooling
• Configuration and stand-by locking
STABILIZED POWER SUPPLY, RS232, LABVIEW, USB*
Protections
• Against short-circuits, by current regulation
• Against overtemperature by fan and thermal
circuit-breaker
• Against overcurrent on main input, by internal fuses
Caractéristiques
• Weight: 3.15kg
• Height: 210mm
• Length: 111mm
• Width: 260mm
Ref. ALR3220
CURRENT GENERATOR AC/DC POWER SUPPLY
Ref. ALR3002M
Réf. AL991S
*USB OPTION
Set comprising an
USB/RS232 adapter + null
modem lead
Ref. USBRS232
• ± 0-15V / 1A or 0-30V / 1A and
2-5,5V / 3A and -15 - 0 - +15V / 200mA
• Power : 48 Watts
• Display: Digital
• Interface: RS-232
• Software: Windows95 minium, LabVIEW
• 0 to 5V, 6V, 12V or 30V / 0 - 25 mA, 250 mA or 2,5A DC
• 6V or 12V or 24V / 5 A AC
• Power : 120 Watts
Reading of voltages and currents on separate displays.
AC & DC voltages available at the same time.
PRODUCTS 2 YEARS GUARANTEE
193
Power supplies
SINGLE OUTPUT DC POWER SUPPLIES (WITH SAFETY TERMINALS Ø4MM)
GPS3030A
GPS3030D
GPS3030DD
GPR3510HD
REF.
Display type
GPS3030A
GPR30H10A
GPS3030D
TYPE A
GPS1850D
GPR3060D
GPR3510HD
90VA
0 to 30V
0 to 30V
GPR6030D
GPR30H10A
DC6140
TYPE A
TYPE DD
0 to 60V
0 to 300V
0 to 30V
0 to 3A
0 to 1A
TYPE DD
180VA to 1000VA
0 to 18V
Adjustable
Current
GPS3030DD
TYPE D
Power
Voltage
DC6140
0 to 30V
0 to 30V
0 to 35V
by 2 knobs coarse and fine from 0 to Vmax
0 to 3A
Adjustable
Regulation
0 to 3A
0 to 5A
0 to 3A
0 to 10A
0 to 5A
1 setting
Output voltage variation : < 0,01% + 3mV - Output current variation < 0,2% + 3mA
by mains variation of 15% or load variation 0 ~ 100%
Ripple & noise
Protection
0 to 6A
by 2 knobs coarse and fine from 0 to I max or 0 to 0
0.5mVrms
Electronic by current limitation against overload and short circuit
Power source
Mains 120-240V - 50/60Hz
Supplied with
Power lead and user’s manual
DISPLAY TYPE
A : analogue type (with voltmeter & ammeter) Class 2,5%
D : digital type. (1 switchable display for Voltage/current)
DD : 2 digital type (1 display for voltage + 1 display for current)
ADDITIONAL ACCESSORIES
Safety leads - Page 225
OPTION
GREEN/YELLOW male earthing socket
Put a «-M» at the end of the references
194
PRODUCTS 2 YEARS GUARANTEE
Measuring apparatus
MULTI OUTPUT POWER SUPPLIES (WITH SAFETY TERMINALS Ø4MM)
GPS3303
SPD3606
GPD3303 - WITH USB CONNECTOR
High resolution 1mV – 1mA,
can be remotely controlled via the USB connection.
Adjustable by numeric keypad or encoder
• Accuracy of programming: voltage 0.03%+10dgt,
current 0.3%+10dgt
• Accuracy of reading: voltage 0.03%+10dgt,
current 0.3%+10dgt
Saving of 4 different configurations
High-resolution display: 30,000V – 3,000 A.
Labview driver.
GPS2303
REF.
SPD3606
GPS2303
INDEPENDENT 1
2 x 0 to 30V - 2 x 0 to 6A
INDEPENDENT 2
GPS3303
2 x 0 to 30V - 2 x 0 to 3A
2 x 0 to 60V - 2 x 0 to 3A
-
SERIAL 1
0 to 60V - 0 to 6A
0 to 60V - 0 to 3A
SERIAL 2
0 to 120V - 0 to 3A
-
PARALLELE
0 to 30V - 0 to 12A
AUXILIARY
0,1 to 5V - 3A
Dims
Weight
0 to 30V - 0 to 6A
-
255 x 145 x 265mm
GPD3303
5V - 3A
255 x 145 x 265mm
6kg
2,5 - 3,3 - 5V - 3A
210 x 130 x 265mm
8kg
Power source
Mains 120-240V - 50/60Hz
Multiple power supplies consist of two or three power sources which are
galvanically isolated from each other.
• 2 adjustable power supplies with rectangular features
PROTECTIVE DEVICES
All of the outputs are protected against short-circuits, even those lasting a long time.
In this case, the power supply will automatically switch to a current source.
AC POWER SOURCES
• Voltage can be adjusted progressively from 0 to Vmax.
• Voltage variation: <0.01% + 3mV or <0.02% + 3mA for 100% load variation
or 15% mains variation.
• Current can be adjusted progressively from 0 to Imax.
• Regulation: background noise <1mVrms.
• Slave repeater error: <0.5% of the master voltage.
• Response time: 0 to Vmax. = 0.1ms.
DISPLAYS
Digital: 3 digits 1/2 LED 13mm. 0.5%
AUXILIARY SOURCE (except for GPS2303)
• Auxiliary voltage: 0,1 to 5V - 3A or 5V - 3A or 2,5 - 3,3 - 5V 3A
• Voltage regulation:
<10mV for 100% charge variation
<5mV for 15% mains variation
• Background noise <2mVrms
THREE OPERATING MODES
Independent mode
Both power supplies are completely independent from each other.
Tracking Series mode
Allow the two power supplies to be used as a 0 to double rating voltage supply.
Tracking Parallel mode
Allow the two power supplies to be used as a 0 to double rating current supply.
PRODUCTS 2 YEARS GUARANTEE
195
Multimeters
AUTO RANGING MULTIMETERS
ST9929
ST9919
Range of reliable and robust automatic multimeters.
Sturdy ABS housing, protected by a shock resistant soft
moulded holster, waterproof (IP67)
REF.
ST9927T
• Peak hold function. Min et Max (exept ST9915)
• Relative measurements
• Bargraph (exept ST9915)
ST9929
ST9919
Display
ST9915
40.000 points
• Hold (ST9929)
• Data recording, max 200s (ST9929)
• Auto power-off after 15min
ST9927T
ST9915
6.000 points
4.000 points
-
Converter
TRMS AC+DC
TRMS AC
TRMS AC
Bandwidth
40Hz to 10kHz
40Hz to 1kHz
40Hz to 1kHz
-
VDC
accuracy
400mV to 1000V
0,06% + 4dgt
600mV to 1000V
0,09% + 2dgt
400mV to 1000V
1,2% + 2dgt
VAC
accuracy
400mV to 1000V RMS
1% + 30dgt - 5% + 30dgt from 1kHz to 10kHz
6 to 1000V TRMS
1 to 2% +3dgt
400mV to 1000V
1,5% + 3dgt
IDC
accuracy
400µA to 10A
1% + 3dgt
600µA to 10A
1% + 3dgt
400µA to 10A
1,5% + 3dgt
IAC
accuracy
400µA to 10A RMS
1,5% + 30dgt - 5% + 30dgt from 1kHz to 10kHz
600µA to 10A TRMS
1,5% +3dgt
400µA to 10A
1,8% + 5dgt
OHM
accuracy
400Ω to 40MΩ
0,3% +4 to 9dgt
600Ω to 60MΩ
0,3% + 4dgt
400Ω to 40MΩ
1,2% + 2dgt
Farad
accuracy
40nF to 40mF
3,5% +10 to 40dgt
60nF to 1000µF
3,5% + 4dgt
4nF to 200µF
3% + 5dgt
40Hz to 10MHz
0,50%
10Hz to 40MHz
0,1% + 1dgt
10Hz to 40MHz
1,2% + 3dgt
Frequency
accuracy
Diode test
Test 0,9mA - 2,8V
. ))))
Duty
accuracy
)
°C (type K)
accuracy
4 - 20mA
Ring for < 100Ω
Ring for < 150Ω
0,1% to 99,9%
1,2% + 2dgt
0,1% to 99,9%
1,2% + 2dgt
0,1% to 99,9%
1,2% + 2dgt
-50 to 1000°C
1% + 2,5°C
-45 to 750°C
3% + 5°C
-
-
-
CAT III 1000V Pol 2
CAT III 1000V Pol 2
4mA~0% ; 20mA~100%
Ranging
Protection
Test 0,3mA - 1,5V
Ring for R < 35Ω
Auto & Manual
CAT III 1000V Pol 2
CAT III 1000V Pol 2
Power source
Dimensions / Weight
Supplied with
1 battery 9V type 6LR61
182 x 82 x 55mm / 430g
Input impedance as voltmeter: 10MΩ
196
182 x 82 x 55mm / 375g
Test leads, thermocouple, carrying case, battery, user’s manual.
PRODUCTS 2 YEARS GUARANTEE
Measuring apparatus
MANUAL RANGING MULTIMETERS
ST9905
2005DMM
Range of reliable and robust manual multimeters.
Sturdy ABS housing, protected by a shock resistant
soft moulded holster, waterproof (IP65)
REF.
UM2010
ST9905 - 2005DMM
• Auto power-off after 15min
UM2010
• Length of the scale: 90mm
• Safety sockets 4mm
ST9905
2005DMM
UM2010
2.000 points
2.000 points
Analogical
VDC
Accuracy
200mV to 1000V
0,5% + 2dgt
200mV to 1000V
0,5% + 3dgt
100mV to 1000V
1,5 %
VAC
Accuracy
200mV to 700V
1,2% + 3dgt from 50Hz to 400Hz
200mV to 200V from 40Hz to 400Hz
750V from 40Hz to 100Hz
1,2% + 3dgt
10 to 1000V
2,5 %
IDC
Accuracy
2mA to 10A (20A during 30s)
1,5% + 3 dgt (3% +10dgt/20A)
2mA to 10A (20A during 10s)
1,2% + 3 dgt (20A ±2%)
50µA to 10A
1,5 %
IAC
Accuracy
2mA to 10A (20A during 30s)
2% + 3dgt (3% +10dgt/20A)
2mA to 10A (20A during 10s)
1 to 2% + 5dgt from 40Hz to 200Hz
3% à 20A
2,5mA to 10A
2,5 %
OHM
Accuracy
200Ω to 200MΩ
1,2% + 1dgt up to 20MΩ
200Ω to 2GΩ
0,8% + 3dgt up to 2MΩ
1 to 1000 kΩ
2%
Farad
Accuracy
2nF to 200µF
4% + 3dgt to 2µF
20nF to 200µF
2,5% + 20dgt up to 20µF
-
Henry
Accuracy
-
2mH to 20H
2,5% + 20dgt
-
Frequency
Accuracy
-
2kHz to 10MHz
1% + 10dgt
-
Ring for R< 50Ω
Ring for R< 90Ω
Ring for R< 50Ω
-
-20 to 1000°C 1% thermocouple K
-
CAT III 1000V Pol 2
CAT III 1000V Pol 2
CAT III 600V Pol 2
182 x 82 x 55mm / 360g
190 x 95 x 45mm / 400g
170 x 110 x 53mm / 500g
0,2A/250V - 5x20mm - fast
20A/250V - 6,3x25mm - fast
200mA - 5 x 20 fast
20A - 5 x 20 fast
HPC 600V 1A
HPC 600V 10A
Display
Diode test
. ))))
)
°C (type K)
Accuracy
1mADC under 2,8VDC max
Ranging
Protection
Power source
Dimensions
Fuses
Supplied with
Manual
1 battery 9V type 6LR61
Housing, user’s manual, test lead
3 batteries LR6
User’s manual, test lead
PRODUCTS 2 YEARS GUARANTEE
197
Multimeters
40.000 COUNTS COMMUNICATING RMS MULTIMETERS
• 3 displays with 2 side displays 4000 counts
• Capacity and frequency measurements,
• Data logging 100 measurements
• Max /min and relative modes
• Bar Graph: Zero on left or central with 40 bars
• Auto power-off: adjustable 0 ~ 30min
REF.
UT71C
Main display
UT71E
40.000 counts
Measurements
TRMS AC + DC
Bandwidth
45Hz to 100kHz
VDC / best accuracy
400mV to 1000V / 0.025% ±5dgt
VAC / best accuracy
4 to 1000V / 0.4% ±30dgt
IDC / best accuracy
400µA to 10A / 0.1% ±15dgt
IAC / best accuracy
400µA to 10A / 0.7% ±15dgt
OHM / best accuracy
400Ω to 40MΩ / 0.3% ±8dgt
Farad / best accuracy
40nF to 40mF / 1% ±20dgt
Frequency / best accuracy
40Hz to 400MHz / 0.01% ±8dgt
Diode test
max 2,8V
. ))))
ring for R< 60Ω
)
Duty / best accuracy
10%~90% / 1% ±30dgt
Temperature °C / best accuracy
-40°C to 1000°C / 1% ±30dgt
4 - 20mA / best accuracy
0,00~100,00% / 1% ±50dgt
Ranging
Auto ranging and manual
Interface
USB
Protection
CEI101 CAT IV 600Veff pol2
Power / accuracy
-
2500 W and 2500 VA / 2% ±5dgt
Power factor ϕ
-
yes
Power source
Dimensions / Weight
Supplied with
198
1 x 9V battery
200 x 93 x 40mm / 380g
USB cable and software, test leads, thermocouple, carrying bag. UT71E only: adapter for W VA cosϕ
PRODUCTS 2 YEARS GUARANTEE
Measuring apparatus
BENCH MULTIMETERS
TRG803
• True RMS measurements
AC+DC or AC only
• Min & max measurements
• Software
• Transistor tester
GDM8351
GDM8341
GDM8145G
• True RMS measurements:
- DC level only
- AC RMS level only
- AC + DC RMS
• Remote control from PC
• Ohmmeter 2 & 4 wires
• dBm, dB, Max Min, compare, store
• Math functions : ax + b, 1/x, %
• Auxiliary display for Hz, dB, ripple
• Option SC1 :16 channels scanner SC1
• Dual display at the user’s choice
• True RMS measurements:
- DC level only
- AC RMS level only
- AC + DC RMS
• High accuracy
• Continuity up to 500Ω
• USB
• True RMS measurements:
- DC level only
- AC RMS level only
- AC + DC RMS
REF.
Display
GDM8351
GDM8341
GDM8145G
TRG803
120.000 counts
51.000 counts
20.000 counts
6.000 counts
50kHz
100kHz
Converter
TRMS AC+DC
Bandwidth
100kHz
VDC
100mV to 1000V
500mV to 1000 V
200mV to 1200 V
600mV to 1000V
VAC
100mV to 750V
500mV to 750 V
200mV to 1000 V
600mV to 1000V
IDC
10mA - 10A
500µA to 10A
200µA to 20A
600µA to 10A
IAC
10mA - 10A
500µA to 12A
200µA to 20A
600µA to 10A
OHM
100Ω to 100MΩ
500Ω to 50MΩ
200Ω to 20MΩ
600Ω to 60MΩ
Farad
10nF to 100µF
10Hz to 1MHz
5nF to 50µF
10 Hz - 1MHz
-
6nF to 6mF
-
10 Hz - 60MHz
Frequencymeter
Diode test . ))))
Max voltage : 6V
°C (type K)
-200 to 300°C type J, K, T
)
Beeper
Max voltage: 1,5V. Buzzer <5Ω
-
Ranging
Interface
-
- 40°C - 1000°C
-
RS232 - USB
Auto & Manual
RS232 - USB
Protection
Power source
Displays the voltage drop
USB
CEI1010 CATIII 300Vrms pol2
115- 230VAC 50/60Hz
100- 240VAC 50/60Hz
230VAC 50/60Hz
Battery or mains 230VAC 50/60Hz
Dimensions / Weight
265 x 107 x 302mm / 2,9kg
265 x 107 x 302mm / 2,9kg
245 x 95 x 280mm / 2,6kg
240 x 105 x 310mm / 2,4kg
Supplied with
PC software & Driver Labview
User’s manual
PC software &
User’s manual
User’s manual
Software, User’s manual
PRODUCTS 2 YEARS GUARANTEE
199
Clamps
AC, DC, AC&DC CLAMPS
PWM
PWM
MS330 - AC
MS332 - AC & DC
• Peak hold function Max
• Auto power off after 15mn
PWM
MS3347 - DC & TRMS AC
• Duty 0,5 ~ 99%
• Auto power off after 10mn
PWM
PWM
MS337
• Peak hold function Min & Max
• Auto power off after 20mn
• Bargraph
MS223
• Auto power off after 25mn
• Recopy output 10mV/A 20kHz
• Back lighting of the screen
• Peak hold function Min & Max
• Auto power off after 10mn
• Recopy output 10mV/A 20kHz
The clamps with the PWM logo are compatible with PWM variator.
REF.
MS330
Display
MS332
MS3347
2.000 counts
Converter
MS337
AC
AC & DC
Bandwidth
10.000 counts
DC & TRMS AC
50 to 100Hz
Opening of the jaws
VDC / VAC
IDC / IAC
MS223
4.000 counts
25mm
29mm
2 to 600V
4 to 600VDC / 400mV to 600VAC
2 to 400A AC only
40 to 400A
AC & DC
AC & DC
50Hz to 500Hz
50Hz to 20kHz
35mm
12mm
400mV to 600V
600V
40 to 1000A
4 to 80A
9,999 to 99,99 A
OHM
200Ω to 20MΩ
4Ω to 40MΩ
9,999 kΩ
Farad
-
40nF to 100µF
4nF to 40mF
40nF to 100µF
-
Frequencymeter
-
5Hz to 150kHz
0 to 4,000 kHz
5Hz to 10MHz
-
Diode test
400Ω to 40MΩ
0,4mA - 1,5VDC test
. ))))
)
Ring for R< 50 Ω
Ring for R< 150 Ω
-
-
°C
Ranging
0,3mA - 1,5VDC test
Auto & Manual
Ring for R< 35 Ω
-40°C to 1000°C
Auto
Protection
2 batteries LR03
205 x 70 x 37 mm / 200g
Supplied with
1 battery 6LR61
200 x 50 x 35 mm / 200g
230 x 80 x 50 mm / 300g
Ring for R< 100Ω
-
-
Auto & Manual
Auto
2 batteries LR03
210 x 70 x 37mm / 200g
Test lead, soft carry case, batteries
ADDITIONAL ACCESSORIES
Oscilloscopes - Pages 190 à 191
200
-
Ring for R< 150Ω
CATIII 600Vrms pol2
Power source
Dimensions / Weight
-
Coaxial leads - See page 220
PRODUCTS 2 YEARS GUARANTEE
202 x 70 x 34 mm / 180g
Measuring apparatus
HIGH SENSITIVITY CLAMPS
UT251A
ST9809
ULTRA SENSITIVE CLAMP
• Allows to measure AC current of some µA (50/60Hz)
• A memory function: storage of 99 measurements
• PEAK measurement
• Autoranging: 0,001mA to 60,00A
• Resolution 1 µA, accuracy ± 1,5% +5dgt
• Allows to measure a current difference between two conductors (differential).
LEACKAGE CURRENT CLAMP
• Allows to measure AC currents of some hundred µA
• Peak hold function: max & min
• Auto power off after 30min
• Bargraph
REF.
UT251A
ST9809
10.000 points
4.000 points
IAC (accuracy)
0,001mA to 60A, automatic ±1,5%
40mA to 100A (2,5% + 15dgt)
VAC (accuracy)
-
400V (2% + 4dgt)
Display
OHM (accuracy)
Protection
-
400Ω (1% + 2dgt)
CEI1010 CAT III 600Vrms Pol2
CEI1010 CAT III 300V
Power source
1 battery 6LR61
Dimensions / Weight
Supplied with
175 x 70 x 38mm / 120g
210 x 62 x 35mm / 200g
Acquisition software, specific USB cable, briefcase.
Test leads, soft carry case
HIGH SENSITIVITY RMS TEST CLAMP
REF. VA21
MEASUREMENTS
ACTIVE POWER
REACTIVE POWER
ENERGY
Batteries : 2 x LR6
AC VOLTAGE
AC CURRENT
LEAKAGE CURRENT
HARMONICS AC VOLTAGE
HARMONICS AC CURRENT
TOTAL HARMONIC DISTORTION
POWER FACTOR
PHASE ANGLE
CREST FACTOR
PRODUCTS 2 YEARS GUARANTEE
• Auto ranging
• Auto power-off after 30min.
• Dim: 210 x 62 x 36mm. Weight: 500g
• Supplied with test leads and carrying case
201
Clamps
MULTIFUNCTIONAL CLAMPS
PWM
PWM
MS232
ST3348
• RMS AC+DC power measurement • RMS AC+DC power measurement
• Peak hold function : Max
• VAC & IAC TRMS measurements
• Autopower off after 30mn
• Frequency
• Back lighting of the screen
• Autopower off after 30mn
PWM
The clamps with the PWM logo are compatible
with PWM variator.
REF.
Display
ST3353
VA6600
• Double display (W & VA, W & ϕ etc.)
• Vrms – Irms - W - VA - VAR - cosϕ - kWh
• Single- and three-phase (3 & 4 wires)
• TRMS in IAC & VAC
• Peak measurements Min and Max
• USB interface + software supplied
• Memory (99 measurements)
• Automatic shutdown at 30mn
• LCD 4 digits and bar graph (lit)
• RMS AC + DC
• Dual display
• U & I , U & Hz , I & Hz , W & cosϕ , VA & VAR.
• Active, reactive and apparent power
• A memory function: storage of 4 measurements
MS232
ST3348
ST3353
VA6600
10.000 counts
4.000 counts
10.000 counts
2 x 4 figures
RMS AC
RMS AC+DC
50 to 60Hz
50 to 200Hz
DC to 400Hz
Ø 53mm
Ø 55mm
Converter
Bandwidth
PWM
PWM
DC + TRMS AC
50 to 500Hz
Opening of the jaws
Ø 30mm
VDC
600V (1% + 5dgt)
400mV to 600V (1,5% + 3dgt)
-
-
VAC
600V (1% + 5dgt from 50 to 500Hz)
400mV to 600V (1,5% + 3dgt)
15 to 750V (1,2% + 5dgt)
VAC+VDC 200 to 600V 2%+5dgt
IDC
600A (1,5% + 5dgt)
1000 A (1,8% + 5dgt)
-
-
IAC
600A (1.5% + 5dgt from 50 to 500Hz)
1000 A (1,8% + 5dgt)
40 to 1000A (2% + 5dgt)
IAC+IDC 200 to 2000A 2%+5dgt
WDC
100 to 360kW
40 to 240kW
-
-
WAC
100 to 360kW RMS
40 to 240kW RMS
0,6 to 750kW
99,99 to 1200kW 2%+5dgt
VA
-
-
0,6 to 750kVA (3% + 5dgt)
99,99 to 1200kVA 2%+5dgt
VAR
-
-
0,6 to 750kVAR (4% + 5dgt)
99,99 to 1200kVAR 2%+5dgt
-
OHM
10 000Ω (1% + 5dgt)
400Ω to 40MΩ (1,5% + 2dgt)
-
frequencymeter
-
5Hz to 100kHz
20 to 200Hz
-
Energy kWh
-
-
1 to 9999kWh (3% + 2dgt)
-
Diode test
-
. ))))
Power factor
Ranging
Protection
Power source
Dimensions / Weight
Supplied with
202
Test 0,3mA
-
-
-
0.3 ~ 1Capacitive or inductive
(0,02 + 2 dgt)
Auto
0,999 2%+5dgt
CATIV 600Vrms pol2
CATIII 600Vrms pol2
Ring for R< 100Ω
)
Auto
Auto & Manual
CATIII 600Vrms pol2
Auto
2 batteries LR03
1 battery 6LR61
4 batteries LR6
1 battery 6LR61
218 x 84 x 30 mm / 270g
229 x 80 x 49 mm / 300g
295 x 100 x 46 mm / 540g
270 x 100 x 45mm / 800g
Test lead, soft carry case, batteries,
user’s manual, USB cable, software.
soft carry case, batteries,
user’s manual.
Test lead, soft carry case, batteries, user’s manual.
PRODUCTS 2 YEARS GUARANTEE
Measuring apparatus
REF.
A138
Display
10.000 points - digital height 12mm
Converter
RMS AC AC+DC
Bandwidth
50 to 400Hz (500Hz VAC)
Opening of the jaws
Ø 42mm
VDC*
100,00 - 1000,0V
VACrms* & VDC+VACrms
A138 : 25 functions
100,00-1000,0V
MAX & MIN (VAC only)
• Manual or auto measurements
• RMS measurements in AC and AC+DC
• 10mV to 1000V in DC, ACrms, DC+ACrms
• 10mA to 1000A in DC, ACrms, DC+ACrms
• Measurement of the call current up to 1400A AC
• Max and Min peaks in voltage and current
• Active power from 1W to 1000kW
• Power factor cosφ from -1.00 to +1.00
• Measurement of the THD and harmonics to row 25
• Resistance from 0.1ohm to 100kohms
• Sound continuity R< 30ohms and diode test
• Frequencymeter 0.01Hz to 10kHz
• Measurement of capacitances from 1nF to 4000µF
• Measurement of temperatures from -50°C to 1000°C
• Indication of the direction of rotation of the phases
• Contactless voltage detector
• Low-pass filter (removes noise)
• Reset button
• Bar graph
• Illumination of the cable to be tested when jaws open
• Display blocking. Backlit display
• Automatic shutdown after 15 minutes
• Low battery indicator
IDC
Best accuracy 0.7% + 2dgt
Best accuracy 1% + 5dgt
140,0 - 1400V
Best accuracy 3% + 15dgt
100,00 - 1000,0A
Best accuracy 1,5% + 5dgt
IACrms & IDC+ IACrms
100,00-1000,0A
Best accuracy 1,5% + 5dgt
MAX & MIN (IAC only)
140,0 - 1400,0A
Best accuracy 3% + 15dgt
100,00-1000,0Hz-10,000kHz
Best accuracy 0.5% + 3dgt
THD total harmonic distorsion
100,0 %
Best accuracy 3% + 10dgt
Harmonic distorsion 1 to 12
100,0 %
Best accuracy 5% + 10dgt
Harmonic distorsion 13 to 25
100,0 %
Best accuracy 10% + 10dgt
100,00-1000,0A
Best accuracy 2,5% + 5dgt
10,000-100,00-1000,0 kW
Best accuracy V x A +10dgt
Frequency
Inrush current
Active power WAC+WDC
Power factor cos ϕ
Resistance
-1,00 to +1,00
Best accuracy 3% + 1dgt
1000,0Ω-10,000-100,00 kΩ
Best accuracy 1% + 3dgt
.))))
Capacitance
Ring for R< 30Ω / Max voltage 1,8V
4,000-40,000-400,0-4000µF
Temperature °C
-50°C to 1000°C
Overload protection
Best accuracy 1% + 1°C
1000Vrms 1000Arms
Ranging
Auto & Manual
Protection
CATIV 600Vrms pol2 / CATIII 1000Vrms pol2
Power source
1 battery 6LR61
Dimensions / Weight
Supplied with
Best accuracy 1,9% + 8dgt
257 x 87 x 50mm / 470g
Soft carry case, test leads, probe, battery, user’s manual.
*Impedance : 3.5MΩ //100pF AC & DC
REF.
VA6200
Display
128 x 64 pts
Converter
TRMS AC
Bandwidth
50/60Hz
Opening of the jaws
Ø 55mm
VAC
VA6200 : Mains analysis clamp RMS AC
4 to 600Vac (0,5% + 5 dgt)
IAC
The screen on this clamp can be used either as a numeric display or as
a graphical screen like an oscilloscope, or as a logging instrument. The
clamp measures the true RMS voltage and current, apparent, reactive,
active, balanced three-phase and single-phase power, cosϕ, peak factor,
total distortion, power consumption and max power demand. In graphics
mode, it displays and quantifies the first 50 harmonics of the signal, the
form of the U and I signals, the single-phase and three-phase diagram.
In logging mode, the clamp stores information in its memory.
The sampling frequency and the start/stop cues can be programmed.
Long acquisitions at high frequencies, with several simultaneous quantities, are possible by using an RS232 output to a PC and special software.
• Measurement of the maximum demand in kW and kVA
• Programmable threshold for transient capture (128 events)
• 32 to 256 points/cycle can be saved on the internal memory
• Memory size: 50,000 logs can be programmed.
• Real time output of: oscillograms, power, settings and harmonics
• Autopower off automatically if not used
• Opto insulated interface (RS232)
4 to 1500Aac (0,5% + 5 dgt)
Power W - VA - VAR
Energy Wh kWh
1000W to 1000kW (1% + 20 dgt)
0 Wh to 999 999 kWh (resp VAh &VARh) (1% + 20dgt)
Crest factor CF
1,00 - 99,99 (5% + 30 dgt)
THD total harmonic distortion
0,0 to 1000,0 % (2% - 6% - 10% as per range)
Power factor
0,000 - 1,000 Accuracy 0,4
Phase angle
- 180° à +180° Accuracy 0,1°
Harmonics of AC voltage in V and in %
0,0 to 100,0% (2% Rang 1 to 20 / 4% Rang 20 to 50)
Harmonics of AC current in V and in %
0,0 to 100,0% (2% Rang 1 to 20 / 4% Rang 20 to 50)
Peak IAC and VAC
Capture of transient events (32000)
Ranging
Auto
Interface
RS232
Protection
Power source
Dimensions / Weight
Supplied with
PRODUCTS 2 YEARS GUARANTEE
CATIII 600Vrms pol2
2 batteries LR06
270 x 100 x 45mm / 800g
RS232 Interface & software, probes
soft carry case. User’s manual.
203
Watt. / Volt. / Amm.
MAGNETOELECTRIC AMMETER & VOLTMETER (EASY TO READ)
V1001
A11
• Sturdy ABS housing, protected by a shock resistant soft moulded holster, waterproof (IP65)
• The four salient corners act as shock absorbers.
• All ranges are selected by one rotary switch.
REF.
V1001
A11
Type
Voltmeter
Ammeter
VDC
100mV to 1000V (1,5%)
-
VAC
3 to 1000V (2%)
-
IDC
-
IAC
-
100µA to 10A (1,5%)
10mA to 10A (2%)
-
100mV for the use of external shunts
mV
Scale length
Protection
Safety terminals
Fuses
Impedances
Dimensions / Weight
Supplied with
90mm
90mm
CAT III 600V Pol 2
CAT III 600V Pol 2
yes
yes
HPC 500V 500mA
HPC 500V 3A + HPC 500V 10A
VDC : 20kΩ/V - VAC : 6,3kΩ/V
-
170 x 110 x 53mm / 500g
170 x 110 x 53mm / 500g
Notice
Notice
Shock absorbers
204
PRODUCTS 2 YEARS GUARANTEE
Measuring apparatus
SAFETY WATTMETER SWITCH
The COWAT11 is a wattmeter switch enabling the measurement of power on an
unbalanced network, with a single wattmeter.
3 positions on the unit:
1 - Measure the current on phase R with voltage between R & T
2 - Wattmeter out of work.
3 - Measure the current on phase S with voltage between S & T.
• Operating voltage:
400V 3-phase + N
• Cutting power
at power factor 0.3=10A
at power factor 1=16A
• CEI1010 CATIII 1000Vrms pol2
ref. COWAT11
1MHZ AC MILLIVOLTMETER
GVT417 is a millivoltmeter for the measuring of sinusoidal voltages from 10µV
to 100V, in the 10 Hz to 1MHz band. The dial is graduated in volts and dB for
the direct measurement of amplifier increases.
RANGES V
300 µV - 1 - 3 - 10 - 30 - 100 - 300mV 1 - 3 - 10 - 30 - 100V
RANGES dB
-70 -60 -50 -40 -30 -20 -10 0 +10 +20 +30 +40 dB
ACCURACY
3 % from 20 Hz to 200kHz
IMPEDANCE
1 MΩ - 40 pF
OVERLOAD
from 300µV to 0,3V: 150VAC / from 1 to 100 VAC: 300 VAC
-
10% from 10 Hz to 1MHz
OUTPUT
A 100mVrms copy output for the full deviation allows the GVT417 to be used as an
attenuator/ amplifier at a constant signal input level.
OTHER FEATURES
Power supply: 115–230VAC 50Hz.
Dim. 142 x 210mm. Depth: 235mm
Weight: 3kg
CEI1010 CATII CL1 300Vrms pol2
ref. GVT417
PRODUCTS 2 YEARS GUARANTEE
205
Watt. / Volt. / Amm.
SINGLE-PHASE DIGITAL WATTMETER
The WECO wattmeter is a multimeter able to measure the following values:
• Active power
• Apparent power
Complete datasheet
• Power factor
www.langlois-france.com
• DC and AC voltage or intensity
• Resistance
• Frequency
• Energy
MEASURING CHARACTERISTICS
WECO displays up to 4 values at the same time, e.g.
U – I – W - PF or U – I – VA – Hz
The WECO energy meter displays the energy consumed in the load in real time in
Wh – kWh and elapsed time in hours, minutes, and 1/10 min.
ref. WECO
LOW RANGES AC SINGLE-PHASE WATTMETERS
These single-phase wattmeters are very easy to connect and use. Double display,
clear marking, low ratings and accuracy are among the advantages of these wattmeters. Also, two free acquisition programs, very simple to use, make the product
complete and very accessible.
All measurements are AC RMS between 40 and 400 Hz.
Ref
U
I
W
Accuracy
Complete datasheet
www.langlois-france.com
PSY6063
PSY6163
260 VAC x 0,1V
600 VAC x 0,1V
1A x 0,1mA / 2A x 1mA
10A x 0,01A
0 to 99,99W x 0,01 W / 0 to 520W x 0,1 W
0 to 6000W x 1W
+/- 1% + 0,5W / 50Hz
+/- 1% + 5W / 50Hz
DISPLAYS AC - 50HZ
Ref
Display
AFF-U
AFF-I
AFF-W
AFF-CM
AFF-WVA
U
I
W
U-I-W
U-I-W
Max voltage
250VAC - 50Hz
/
250VAC - 50Hz
250VAC - 50Hz
250VAC - 50Hz
Max current
/
5A - 50Hz
5A
5A
5A
Accuracy
Dimensions
206
± 2%
± 2%
± 2%
± 2%
± 2%
175 x 85 x 80mm
175 x 85 x 80mm
200 x 150 x 110mm
200 x 150 x 110mm
250 x 150 x 110mm
PRODUCTS 2 YEARS GUARANTEE
Various apparatus
Measuring apparatus
MAINS ANALYSER
V A W VAR VA POWER FACTOR THD HARMONICS
The 6830 analyser is well suited to taking measurements in both living and educational spaces due to low
current ratings (999.9mA) and low power ratings (999.9 W – 999.9VAR – 999.9VA). It is also suitable
for industry due to its high ratings, the analysis of 3-wire and 4-wire unbalanced three-phase and single
phase networks, the detection of transience, a comprehensive current and voltage analysis, and harmonic
distortion. 4 display modes: electrical quantities (35 simultaneous parameters), dual-trace oscilloscope,
harmonic analysis and Fresnel diagram.
FUNCTIONS
RANGES
999,9 W - 9,999 - 99,99 - 999,9 - 9999 kW
ACTIVE POWER
REACTIVE POWER 999,9 VAR - 9,999 - 99,99 - 999,9 - 9999 KVAR
APPARENT POWER 999,9 VA - 9,999 - 99,99 - 999,9 - 9999 kVA
1% + 8dgt
1% + 8dgt
6kHz
1% + 8dgt
999,9 mA - 9,999 - 99,99 A
12kHz
0,5% + 5 dgt
VOLTAGE TRMS
600,0 V
12kHz
0,5% + 5 dgt
POWER FACTOR
0,00 à 1,00
0,04
PHASE ANGLE
-180° to 180°
1°
Capture of pics V
600,0 V
5%
Capture of pics A
999,9 mA - 9,999 - 99,99 A
5%
CREST FACTOR
1,00 to 99,99
0,0 to 20,0 %
20,0 to 100,0 %
5%
1%
3%
100,0 to 999,9 %
10%
HARMONICS order 1 ~ 100
RANGES
ACCURACY
measured in / expressed in
Supplied accessories
• 3 multiple-rating hook-on ammeters: 1 - 10 - 100A
• 4 measurement leads + crocodile clips
• 1 RS232/USB cable + software + handbook
• 1 mains adapter
• 1 carry case
ACCURACY
INTENSITY TRMS
THD-F
ref. 6830
Bandwidth
6kHz
6kHz
as per order
VOLTAGE / in VOLT
600.0 V
2 ~ 6%
VOLTAGE / % of the fundamental
0.0 ~ 100.0%
2 ~ 6%
CURRENT / in mA or A
999.9 mA - 9.999 - 99.99 A
0.2 ~ 35%
CURRENT / % of the fundamental
0.0 ~ 100.0%
0.2 ~ 35%
Networks
• 2- and 3-wire single-phase
• 3- and 4-wire three-phase Balanced or otherwise.
Displayed measurements
• phase-to-ground and composite RMS voltages
• RMS voltage of the neutral/earth
• RMS currents in phases and neutral
• RMS voltages and current peaks
• average current, average voltage
• Power, W, VAR and VA in each phase
• total power W, VAR and VA in the charge
• average power W, VAR and VA
• power peaks W, VAR and VA
• Power factor and average Power factor
• phase shift of the phase-to-ground and composite
voltages
• phase shift of currents in the phases
• consumption WH, VARH and VAH
Harmonics 1 to 99
• RMS currents and voltages of harmonics
• harmonic currents and voltages as a % of the fundamental component
• frequency and distortion of harmonics
• THD-F (total harmonic distortion)
• Imbalance ratio between voltages
• Fluctuation ratio between voltages
• Imbalance ratio between currents
• Fluctuation ratio of currents
PRODUCTS 2 YEARS GUARANTEE
Capture of transients
• overvoltages – undervoltages – lack of a phase
Memory capacity
• up to 28 files of transients
(from all of the measurements)
• 2.4 MB
Data transfer
• screen files (measurements, harmonics, Fresnel
diagrams and transients)
• RS232 – USB optical link.
• Supplied software.
Screen hard copy
• table of measurements, oscillograms,
harmonics and Fresnel diagrams
Miscellaneous
• Internal calendar:
year-month-day-hour-min-sec
• Power supply 230VAC 50/60Hz
• 106 x 60mm backlit LCD screen
• Dim: 25 x 155 x 57mm Weight: 1.2kg
207
Various apparatus
INSULATION TESTER
The ST5500 megohmmeter has 4 measuring functions: insulation resistances with 3 test voltages
(250V, 500V, 1000V), resistors, DC voltage and AC voltage.
ref. ST5500
Info battery : 6 x LR14
FUNCTION
RANGES
RESOLUTION
MΩ
200 - 2000MΩ
100kΩ - 1MΩ
250 – 500 – 1000V/1mA
Withstanding voltage /current ACCURACY
3,5% + 5dgt
Ω
200Ω - 200kΩ
0,1Ω - 100Ω
< 8V
1% + 2dgt
.)))
Ring for R< 40Ω
VDC
1000V
1V
0,8% + 3 dgt
VAC
750V
1V
1,2% + 10 dgt
200 mA when R < 40Ω
TECHNICAL CHARACTERISTICS
• Insulation tests: 1mA rated current using the rated test voltage for fast-charging of the capacitors.
• .))) in the ohmmeter position, the unit will make a sound if the tested resistance is less than 40Ω.
In this case, the 200mA current is used to detect a poor connection.
• The HOLD key locks the display, and the LOCK key maintains the test voltage in the high-capacity wires which take longer to charge.
• Batteries: 6 x 1.5V (AA type)
• Dimensions: 200 x 92 x 50mm. Weight: 700g.
• Supplied accessories: test leads and case
• CEI1010 cat III 1000V pol2
MEGOHMMETER GIGOHMMETER
EARTH RESISTANCE TESTER
Complete datasheet : www.langlois-france.com
Complete datasheet : www.langlois-france.com
Measure high values of insulationresistance
according to 4 test voltages: 500V, 1000V,
2500V and 5000V. It displays at the same
time the insulation resistance in the middle of
the screen (large digits), the instant test voltage and the total time since the beginning of
the test.
ref. ST6605
Earth resistance meter which measures using the
auxiliary earths method.
• Functions : earth resistance, resistance, continuity
test,VAC, VDC
• Large display for measuring and an auxiliary display for battery voltage
• Lock key for continuous test
• Accessories supplied :
2 earth pegs
5 linking cables or free coupling connectors
1 carry case
• Functions : VDC - VAC - OHM
• Display LCD 6000 counts
• Accessoiries supplied :
3 test leads + crocodile clips,
1 high voltage test lead,
1 main adapter,
1 transport case
CLAMP METER FOR MEASURING EARTH
ref. ST5300B
RESIDUAL CURRENT DEVICE TESTER
Complete datasheet : www.langlois-france.com
VA5601 is a clamp used for measuring earth, even in
complex network, with no need to use pegs,or to open
the circuit. VA5601 facilitates analysis by measuring
each earth individually. VA5601 can also measure the
leakage current in the earth conductor.
EARTH MEASUREMENT:
The clamp has 9 ratings
which are automatically switched.
MEASUREMENT OF THE LEAKAGE CURRENT:
The clamp has 7 ratings
which are automatically switched.
CA-DT33 gathers in one device all the essential functions to control and visualize
instantly the quality and the conformity of electrical installations 230V : voltage
presence, connection to the earth, residual current device of type AC or A
This apparatus is made for domestic, commercial and industrial installations.
• Control switch of residual currents of type AC and A
from 10 to 650mA (5 steps).
• Usable on standard wall socket 2P or 2P+E 10/16A of single-phase 230V
circuit between PHASE and NEUTRAL.
• Earth connection indicator (GREEN LED).
• Phase position on the left or the right
by manual selection (RED LIGHT).
Weight: 0.75 kg
ref. VA5601
ref. CA-DT33
208
PRODUCTS 2 YEARS GUARANTEE
Measuring apparatus
RESIDUAL CURRENT CIRCUIT BREAKER TESTER
• Measurement & check possible under voltage
• Rechargeable apparatus (batteries supplied)
• LCD display
• TRMS converter
• Automatic test sequences
• Programmable delay lines
• Loop impedance and line impedance
• Good / bad indicators
• Test lock
Inspection, maintenance
and periodic testing of
electrical installations.
Evaluation of measures of
protection low voltage installation. Troubleshooting
on under voltage installations. Field device with
rechargeable batteries.
• Tests on single and three phase systems
• Magnetic back for hands free
• On the screen edge, green light for test OK,
and red light for all errors.
• Direct help on the screen
• Protection: 300V CAT IV / 600V CAT III
• Test of residual current circuit breakers according the
norm EN 61557-6
• RS232 / USB Interfaces
FUNCTIONS : Nominal trip out current IΔn, Contact voltage in V, Trip out current,
RCD trip out time (ms), Loop impedance, Line impedance, Operating voltage, Operating frequency
ref. SMARTEC-22 (with accesories)
Complete datasheet
www.langlois-france.com
ref. SMARTEC-LOG data mining software option
ELECTRICAL INSTALLATION TESTER
The XE electrical installation tester brings together in a single piece of equipment the majority of
the functions which are necessary for checking domestic and business premises in accordance with
standard NFC15-100. In particular: current, voltage, earth measurement, earth continuity, trigger
current and time of differentials, insulation resistance, calculation of short-circuit and fault currents,
resistance of the mains and earth loop, calculation of fuses and phase rotation, etc.
The graphical screen displays the results and the measurement settings numerically. By simply pressing the HELP key, the connection diagram(s) corresponding to the position of the switch will appear
on the screen. XE has 2 ports: RRS232 and USB to be connected to a PC. The software, which is
supplied as standard, can be used to export data from the memory of the XE to a spreadsheet, or
to edit a measurement report.
The unit is supplied with a storage case and all of the accessories required to undertake all measurements, except for a blind clamp ammeter and the luxmeter unit (available as an option).
ref. XE (with accessories)
VOLTAGE TESTER
EARTH & CONTINUITY MONITOR AND TESTER
Voltage detector ST9121 complies with IEC standard 612433 concerning test equipment for low-voltage electrical installations.
This mark certifies this compliance. The mobile
probe can also be attached laterally alongside the main
probe, with a standard gap of 19mm from the 230V sockets
to the safety eclipses. The probes are equipped with contact
plates with retractable cover for connection to terminals 4mm
in diameter. The mini-flashlight at the end of the probe allows one to illuminate a dark area. The AUTO TEST key
checks the ST9121 before and after each use. This LED indicates the presence of dangerous voltage, even with no batteries. 8 LEDs indicate DC or AC voltage from 12 to 690V DC or
V AC 50Hz. 2 LEDs determine the polarity if voltage is DC or
AC. This LED lets one distinguish neutral phase(s).
The L and R LEDs determine the order of the L1 L2 L3 phases in
three-phase setups.
ref. ST9121B
Complete datasheet
www.langlois-france.com
ref. LUX1172 Luxmeter unit
Once it has been directly connected to a 2P+E socket, the earth & conductivity
monitor and tester CA-OHM2 can provide the following information:
• Voltage presence
• Normal or abnormal voltage
• Phase position
• Connection of earth to male prong
• Measurement of earth resistance
• Continuity control of metal parts (accessory supplied)
The display will be BLUE
• if all of the controls are normal.
The display will be RED
• if the earth value is greater than 100 ohms
• if the mains voltage is abnormally high
• if there is no earth
Weight: 0.75kg
Battery : 2 x LR03
Other characteristics
Double insulation case . Working cycle : ED=30s
Response time
< 0,1s In < 3mA AC or DC
Is<20mA at 690Vrms
Conforms with the CEI 1010 norm Pol2
CATIV-600V CATIII-1000V
ref. CA-OHM2
Accessory supplied
Probe on cable drum with 7m thread for
checking conduction.
PRODUCTS 2 YEARS GUARANTEE
209
Various apparatus
SPOT INFRARED THERMOMETER
SOUND LEVEL METER
ST8829 measures temperatures remotely –
beyond two metres – with a very narrow
measuring cone. This special feature means
that the temperature in an area measuring
just a few millimetres in diameter can be
taken. This makes it possible to measure the
connection temperature of a poorly tightened terminal, fuse or electric cable, etc.
A red laser beam parallel to the axle of the
measuring cone points to the area where the
temperature is to be taken.
Dim.: 230 x 100 x 56 mm. 290 g
Battery : 1 x 6LR61
ref. ST8829
This sound level meter measures the acoustic pressure. The purpose is to determine and control the
noise pollution in the working area, in conformity
with the norm CEI61672-1 Class 2.
laser pointer
ref. ST8852
Battery : 1 x 6LR61
Temperature cone measurement
Optical resolution
RANGE
RESOLUTION
ACCURACY
TIME BASE
OPTICAL resolution*
- 50°C to 1000°C
0.1°C up to 200°C
1°C from 200 to 1000°C
1.5% of reading
< 1 sec
50/1
* Optical resolution = L/Ø
DUAL THERMOMETER
ST613 is a thermometer with two inputs for thermocouple type K. The range of measuring temperature is – 50°C to 1300°C. Within the range
– 50 °C to 1000 °C the resolution is 0.1°C
The dual displays shows temperature of each
probes, or the difference of temperature
between the two probes.
ST8852 measure in dB the acoustic pressure
- According two integrating periods: slow (S: 1s) or fast (F: 250 ms)
- With 2 frequency correction filter: A (human sensibility) or C (materials)
• Frequency range: 31.5 Hz to 8 kHz / Accuracy: +/- 1.4 dB
• Auto range: 30dB to 130 dB
• Manual ranges: 30~80dB 50~100dB 80~130dB
• Display: 4 digits, 0.1dB resolution, backlight function
• Functions: MAX/MIN – HOLD – Alarms
• USB interface (data in formats .txt or .xls)
• Application software: Curve drawing, cursors, measuring charts, stats.
• Analogical output: in AC: 1Vrms, DC = 10mV/dB
• Auto power off after 15min
• Supply: 9V battery
• Dims/weight: 278 x 76 x 50mm / 350g
Supplied accessories: software, USB cable, tripod, mains adapter
SHUNT
ref. ST613
RANGE
-50 to -100°C
-100 to 1300°C
ACCURACY
T1 & T2
0.5% + 2°C
0.15% + 1°C
ΔT = T1-T2
0.5% + 1°C
0.5% + 1°C
• Display: 10000 counts
• Unit of temperature : °C or °F or °K
• Max & Min hold function
• Average of temperatures recorded during a
time adjustable from 1s to 99min 59s
• Supply: 9V battery (type 6F22)
• Auto power off
• Large digits 17mm
• Dimensions: 165 x 76 x 43mm. Weight:
0.4kg
Accessories: 2x type K thermocouple: stainless
steel tube with handle: Ø3.2mm
210
Accuracy 0,5%.
Ref.
Current
Drop voltage
HU10-100
10A
100mV
HU20-100
20A
100mV
HU25-100*
25A
100mV
HU40-100*
40A
100mV
HU60-100*
60A
100mV
* Double current terminals compatible with laboratory leads.
PRODUCTS 2 YEARS GUARANTEE
Measuring apparatus
DIGITAL LUXMETER
PYRANOMETER
LX337 is a compact luxmeter with autoranging
that can be manually overridden.
• Accuracy: 3% of the rdg + 5 dgt
• Response time: 0.5 seconds
• Response curve: maximum sensitivity centred
around 570 nm
• Auto & manual power off
• Power supply: 9v battery
• Dimensions: 196 x 54 x 33mm.
• Weight: 180g
ref. LX337
Battery : 1 x 6LR61
RANGES in lux
RESOLUTION
39,99
0,01
399,9
0,1
3999
1
39990
10
The PYR1307 pyranometer measures the
power of solar radiation in watts per m2:
W/m2
• Ratings: 199.9 W/m2 and 1,999
W/m2
• Measuring error: < 10W/m2 or 5% of
the reading
• Display: 2,000 pixel LCD
• Captures min. and max. values
• "Hold" key allows one to freeze
the display
• Backlighting
• Supplied with a carry case
• Dimensions: 162 x 63 x 28mm
• Weight: 250g
Battery : 1 x 6LR61
ref. PYR1307
4-20MA LOOP CALIBRATOR
• in % of the output span to supply a typical intensity like 4 – 8 – 12 – 16 or 20mA
• linear ramps with low and high selectable levels as well as timing
• programming of manual ramps step by step with selectable amplitude
• programming of auto ramps by steps with selectable amplitude and timing
• Beeper warning when output is open
ref. VA100
GAMME
RESOLUTION
PRECISION
Info Piles : 1 x 6LR61
4 - 20 mA
1µA
0,025% + 5µA
0 - 20mA
1µA
0,025% + 5µA
0 - 24mA
1µA
0,025% + 10µA
4 - 20V
1mV
0,05% + 5mV
0 - 20V
1mV
0,05% + 5mV
0 - 24V
1mV
0,05% + 10mV
• Display: 5 digits
• Carry case, user’s manual, external battery
Pack (for 6x 1.5V AA batteries)
• Input for mains adapter DC 12V (not included)
• Dimension: 88 x 168 x 26mm
• Weight: 330g
3-PHASE TESTER
ST850 is a simple and robust tester allowing the detection of a voltage on a line and the order of the phases.
• Voltage sensing: 3 lamps indicate the presense/absense of a voltage on each of the three 3 phases
• Phase order: The circle turns clockwise, if the phases are connected in the right order
• Maximum voltage 1600 VAC for 1 min
• Box fully isolated 130x80x43mm. Weight. 550g.
• CEI1010 CATII 600Vrms pol2
• CEI1010 CATIII 300Vrms pol2
ref. ST850
PRODUCTS 2 YEARS GUARANTEE
211
Various apparatus
TACHOMETER
TACHO METER WITH MEMORY AND SOFTWARE
AT8 combines in one case a light-sensing detector and a sensor for measurement by contact.
With memory which records the maximum, minimum and average value. Delivered with one
rubber cone for direct measuring by contact on
shafts, and one disk for the scrolling measuring
(band in movement).
• Display LCD 11mm 0 5 digits
• Light sensor measurement 2 to 100 000 rpm
• Contact measurement 2 to 20 000 rpm
• Accuracy 0,05% reading + 1dgt
• Measurement unit: rpm m/min Hz m
• Sample time 0,5s
• Detection distance 50 to 500mm
• Time base: Quartz
• Memory : 10 measurements
• Min Max average value for each measurement
Dimensions : 210 x 58 x 36mm. Weight 180g.
Battery : 1 x 6LR61 (9V)
Supplied with contact accessories and carry case.
ref. AT8
• Large LCD 6 digits with backlit
• Contact and non-contact measurement in the same device
• Measurement distance: from 40 to 500 mm
• USB datalogger (20 000 measurements)
• Sampling period: from 62.5ms to 2s
• Contactless rotation speed measurement:
from 30.00 to 99 9990 rpm on 4 ranges
• Contact rotation speed measurement:
from 15.00 to 19 999 rpm on 4 ranges
• Contactless rotation speed measurement:
from 0.5000 to 1600 rps on 4 ranges
• Contact rotation speed measurement:
from 0.2500 to 333.0 rps on 4 ranges
• Circumferential speed measurement:
from 1.500 to 1999.9 m/min
• Circumferential speed measurement:
from 0.0250 to 33.30 m/s
• Period measurement in ms,
for deduction of frequency
• Lap counter
• Rotation on buzzer beep
Features
Automatic range switching,
Average, Max/Min,
Auto power saver, Hold function,
Buzzer (ON/OFF)
Dimensions: 186 x 76 x 36 mm
Delivered with carrying case, contact
Battery info: 1 x 6LR61 (9V)
accessories,
reflective tape, connection
ref. DT-LOGGER
lead and software.
STROBOSCOPES
STA10K and STA269 are both stroboscopes with the same flash lighting circuits.
COMMON FEATURES
• Stroboscopes with xenon lamp, a flash duration of approximately 60µs and a power of 40W.
• LED digital display indicating the rotation speed in revolutions/minute (RPM)
• 230V AC mains power supply.
• Ventilated focussing lens to protect the flash tube. Parabolic mirror.
• Power supply 230VAC 50/Hz
• Dimensions: 210 x 120 x 120mm. Weight: 1kg.
• ABS housing
STA269 with
external synchro
Ref
Rotation speed
Accuracy
Functions
Nb dgts
Ext trigger
Memory
RS232 output
STA10K
100 to 10000 rpm
0,05%
rpm
4
/
/
/
STA269
5 to 12500 rpm
0,01%
rpm & Hz
5
pulse 5V
10 memories
yes
ENERGY METER
Energy counter (ME type) commonly encountered in housing buildings. Easy to use thanks to 3 intuitive
navigation keys. Works by direct measuring without current transformer
• LCD display
• Current up to 63A
• Totalizer counter and Partial counter with zero reset
• Autonomous supply
Ref
Voltage and frequency of use
Measuring range
Display of date & hour of zero-reset
Impersonal output
Counter indicator light
212
ME66 single-phase
ME71 3-phase + N
230/400V – 50/60Hz
230V – 50/60Hz
0 to 99 999 999,99 kWh
0 to 99999 kWh
No
Yes
Adjustment from 1Wh to 1 kWh
1000 lightnings by kWh
500 lightnings by kWh
PRODUCTS 2 YEARS GUARANTEE
Measuring apparatus
LCR BRIDGE
DATA RECORDER
ref. ST9930
Battery : 1 x 6LR61
RESISTANCE
110,00Ω
1,1000kΩ
11,000kΩ
110,00kΩ
1,1000MΩ
11,000MΩ
110,00MΩ
ACCURACY
1,2%± 0,5 Ω
1,2%± 5dgt
1,2%± 5dgt
1,2%± 5dgt
1,2%± 5dgt
1,2%± 5dgt
1,2%± 5dgt
CAPACITANCE
11,000nF
110,00nF
1,1000µF
11,000µF
110,00µF
1,1000mF
11,000mF
110,00mF
ACCURACY
5%± 0,7nF
5%± 15dgt
5%± 15dgt
3%± 10dgt
3%± 10dgt
3%± 10dgt
10%± 10dgt
10%± 10dgt
INDUCTANCE
11,000mH
110,00mH
11,000H
20,000H
ACCURACY
2%± 50µH
2%± 50µH
5%± 50mH
5%± 200mH
ref. ST176
Battery : 4 x LR03
Simple to use, this is a precision instrument intended to record RMS alternating
currents and voltages. The sampling period can be set from 1 second to 24
hours. Each channel can store 128,000 data items.
The current range is 2-200A, the voltage range is 6-600VAC.
It is supplied with one USB cable and software for storing data and viewing
voltage and current curves on a PC, 2 clamp-on ammeter and 2 voltage probes
terminated with 2 tips.
Memory size:
128 kpoints per channel (voltage and current)
256 kpoints current (or voltage)
1s to 24 hours
2A to 200A ACrms
±2% ±1A
0.1A AC
6 to 600VACrms
±2% ±1V
0,1VAC
capture of max and min of reading
manual or automatic
40Hz to 1kHz
4 batteries LR03 (AAA)
114 x 63 x 34mm / 248g
Sampling speed
Current range
Current accuracy
Current resolution
Voltage range
Voltage accuracy
Voltage resolution
MAX hold
Start blip
Frequency range
Power supply
Dimensions/Weight
ST9930 is able to measure resistance,
capacitance & inductance.
• Inputs protection: 600 Vrms
• Display: 11000 counts
• Manual and Auto ranging mode
• Relative measurements
• Recording of max and min values
• Diode test under 300µA
• Continuity: rings if R< 30Ω
• Hold display mode
• Auto power-off after 10 min
• Back lighting of the screen
• Shock resistant, soft moulded holster.
• CEI1010 CATIII 600V
SINGLE PHASE AND THREE PHASE MULTIFUNCTIONAL COUNTERS
Complete datasheet
www.langlois-france.com
CMPT
CMPM
UL37
Ref.
CONNECTION
ELECTRICAL NETWORK
SPAN RANGE 1
COMMUNICATION
DIMENSIONS
CMPT
3-phase
230/400VAC 50/60Hz
20mA…30A
Ethernet
330 x 200 x 80mm
CMPM
Single-phase
230…240VAC 50/60Hz
20mA…30A
Ethernet
330 x 200 x 80mm
UL37
3-phase
230/400VAC 50/60Hz
20mA…30A
-
250 x 150 x 110mm
PRODUCTS 2 YEARS GUARANTEE
213
Decade boxes
DECADE RESISTANCE BOXES
R80
• Safety terminals
• Double insulation
• Frequency range:
0 to 500 kHz at an accuracy 0.5%.
RESISTANCES
Power : 0.5 W permanent
Type : 0.1 et 1Ω coils / 10Ω to 1MΩ
metal film to 50 ppM.
R4
Ref.
Nb of decades
Resistances
Dims.
R0
1
10x0,1Ω
82x82x60
R1
1
10x1Ω
82x82x60
R2
1
10x10Ω
82x82x60
R3
1
10x100Ω
82x82x60
R4
1
10x1kΩ
82x82x60
R5
1
10x10kΩ
82x82x60
R6
1
10x100kΩ
82x82x60
R7
1
10x1MΩ
82x82x60
R40
4
from 10x1Ω to 10x1kΩ
290x80x60
R50
5
from 10x1Ω to 10x10kΩ
420x80x60
R60
6
from 10x1Ω to 10x100kΩ
490x80x60
R70
7
from 10x1Ω to 10x1MΩ
490x80x60
R80
8
from 10x0,1Ω to 10x1MΩ
490x80x60
CEI1010 CATIII 1000Vrms pol2
DECADE INDUCTOR BOXES
Ref.
L70
• Safety terminals
• Double insulation
TYPE OF COILS
Coils-wound on ferrite cores, with a central
core, which ensures a high Q factor. L70-AR
coils without core hence best accuracy &
inductance independent of the frequency
Nb of decades
Accuracy
L1
1
10%
10x1µH
82x82x60
L2
1
10%
10x10µH
82x82x60
Dims.
L3
1
10%
10x100µH
82x82x60
L4
1
10%
10x1mH
82x82x60
L5
1
10%
10x10mH
82x82x60
L6
1
10%
10x100mH
82x82x60
L7
1
10%
10x1H
82x82x60
L40
4
10%
10x1mH to 10x1H
290x80x60
L50
5
10%
10x100µH to 10x1H
420x80x60
L70
7
10%
10x1µH to 10x1H
490x80x60
L70-AR
7
5%
10x1µH to 10x1H
490x80x60
L2
Ref
Inductance
CEI1010 CATIII 1000Vrms pol2
Decade
10x1µH
10x10µH
10x100µH
10x1mH
10x10mH
10x100mH
10x1H
L70
10%
I
R in Ω
250mA
10 x 0,003
180mA
10 x 0,05
150mA
10 x 0,02
100mA
10 x 1,5
70mA
10 x 12
50mA
10 x 100
30mA
10 x1k
L70-AR
5%
I
R in Ω
1A
10 x 0,005
1A
10 x 0,05
1A
10 x 0,5
400mA
10 x 5
125mA
10 x 50
40mA
10 x 500
12mA
10 x 5k
LABORATORY INDUCTORS
These inductors, without magnetic core, are wound on insulating material chucks, giving them a good stability on a wide
frequency range.
• Shock-proof plastic box with safety terminals.
• Double insulation
• Dimensions : 82 x 82 x 64 mm
Ref.
Inductance
LA01
Accuracy*
Current
0,1H
5%
400mA
36,0 ohms
LA1
1H
5%
125mA
380,0 ohms
LA5
5H
5%
50mA
2100 ohms
* 1% to 1kHz
214
Resistance at 20°C
PRODUCTS 2 YEARS GUARANTEE
CEI1010 CATIII 1000Vrms pol2
Measuring apparatus
DECADES CAPACITOR BOXES
C50
Ref.
Nb
of decade
Accuracy.
at 20°C
Capacitance
Dims.
mm
C50
5
1%
from 10x100pF
to 10x1µF
420x80x60
C1
1
1%
10x1nF
82x82x60
C2
1
1%
10x10nF
82x82x60
C3
1
1%
10x100nF
82x82x60
C4
1
1%
10x1µF
82x82x60
CEI1010 CATIII 1000Vrms pol2
• Capacitors are plastic film, non polarisated.
• Operating voltage : 400 VDC or 250 VAC
• Temperature drift : 80 ppM / °C
• Safety terminals
• Double insulation
C4
CAPACITOR LINK BOXES
Réf.
Nb
of link
Accuracy.
at 20°C
Capacitance
Dimensions.
(mm)
C30
5
5%
from 5µF to 105µF
170x135x110
C20
6
1%
from 0,5µF to 20,5µF
190x110x60
C10
6
1%
from 0,05µF to 2,05µF
190x110x60
CEI1010 CATIII 1000Vrms pol2
C20
• Capacitors are plastic film, non polarisated.
• Operating voltage : 400 VDC or 250 VAC
• Temperature drift : 80 ppM / °C
• Safety terminals
• Double insulation
BOX WITH 7 POSITIONS OF RATIO
b
The K7 box is made up of two arms « a » and « b » of a Wheatstone Bridge. The two
other arms form the resistance
« X » to be measured and the calibrated variable resistor « r ».
• At balance X = r a / b
• Number of scales k = a / b: 7 positions
0.001 - 0.01 - 0.1 - 1 - 10 - 100 - 1000
• Dimensions: 82 x 82 x 60mm.
• Double insulation
CEI1010 CATIII 1000Vrms pol2
r
G
X
a
X=r
a
b
ref. K7
ZEROING GALVANOMETER
FUNCTIONS
RANGES
INTERNAL RESISTANCE
ACCURACY
VDC
- 100mV 0 + 100mV
4 kΩ
1,5 %
IDC
- 30µA 0 + 30µA
1,7 kΩ
1,5 %
IDC
- 3 mA 0 + 3 mA
40 Ω
1,5 %
ref. GAL
CEI1010 CATIII 600Vrms pol2
• Suitable for assembling in Wheatstone or Thomson bridge.
• Length of the scale: 90mm
• Safety sockets 4mm
• Protection at all ranges
• 1 fuse HBC 500V / 500mA
PRODUCTS 2 YEARS GUARANTEE
215

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project