av35 video/cd/usb/sd
DAN•SOUND ApS
Grøndalsvej 39, DK-4690 Haslev
Tel.: +45 5631 4500
Fax: +45 5631 6050
www.dan-sound.dk
dan-sound@dan-sound.dk
Shown TV and projectors is is randomly selected and is NOT included.
Is only intended as an illustration of,what AV35VIDEO can handle.
DAN-SOUND ED-100B
CASSETTE ACCESSORY
All units are subject to continuous improvementsnon-binding pictures and specifications
AV35 VIDEO/CD/USB/SD
All units are subject to continuous improvements
non-binding pictures and specifications
IMPORTANT INFORMATION ABOUT S.P.L. (Sound Pressure Level)
§1:
MAX. VOLUME
HOW LOUD
SHOULD I PLAY ?
You can turn-up volume until AUDIBLE DISTORTION just occurs - and then turn down a little. Turning BASS fully up, point of distortion will be reached remarkably faster than if the BASS have been in
middle position - or a little lower.
Damages on loudspeaker and/or amplifier caused by audible distortion will NOT be covered by
any warranty ! This kind of damages are easily recognized.
DAN-SOUND cannot be held responsible for any hearing damages caused by high S.P.L. or other
kind of misuse. Check your local rules and regulations.
KEY
FUNCTION
CD / CASSETTE
This potmeter adjust sound level for DVD/CD/MP3/USB/SD and CONNECTED cassette accessory. Turning
it, DISPLAY shows dB-values from 0 to 40dB. The potmeter have no start/stop point. The displayed dB-value is not indicating the actual sound level !!
The actual sound level might exceed the recommended maximum sound pressure level. Check local rules
and regulations.
MP3-MIC-AUX
This potmeter adjust sound level of program generated by CONNECTED devices.
These devices should be connected to AV35VIDEO’s corresponding JACK-CONNECTORS.
MIC and AUX is 6,3mm Mono Jack connectors and MP3/I-POD is standard 3,5mm stereo jack connector
(playback in mono !)
If not in use, this potmeter should be put to ZERO position, to avoid collecting noise.
BASS
This potmeter adjusts the BASS level - more / less bass.
More BASS will drain the amplifier power much faster than a middle/lower position.
HINT: Do not use additional BASS if not necessary. Place AV35 in a corner, and additional bass occurs naturally - without further draining of amplifier !
TREBLE
This potmeter adjusts the TREBLE level - more / less treble.
Please use middle position, and do only make adjustments if necessary. (Minor draining only)
LINE OUT
From these RCA-plugs (Phono) you can have a UNREGULATED LINE SIGNAL from all the CD functions as well as connected devices - or the cassette accessory, which is not included.
VIDEO OUT
YELLOW Phono Plug: COMPOSITE Video signal, consisting of both video and audio signals. Connect to
matching plug on TV or Projector. Medium to low picture quality.
Blue/Green/Red Plugs: COMPONENT video signal, only consisting of video signals. High quality - Please
consider to use high quality cables.
This output can also supply a screen/projector with RGB-multi-pin plug. Please choose suitable cable.
MIC
Connect your microphone here. Please consider that a cheap PLASTIC microphone generates PLASTIC
sound !! Choose a better type of microphone. AV35 deserves it !!
NOTE: Only a MICROPHONE should be connected to this input. Connecting other devices with high signal
output might damage the preamplifier. Some WIRELESS microphone receivers with low signal output (app.
2mV) can be connected here, but please try “AUX” first !
AUX
Connect all other external devices with UNREGULATED LINE SIGNAL here (100-300 mV)
NOTE: Connecting a LOUDSPEAKER OUTPUT SIGNAL might cause damage.
Wireless microphone receivers with high output (100-300mV)should be connected to AUX.
PHONES
This 3,5 mm Headphone output is considered as “Master”, and BREAKS the built-in loudspeaker when connected. This output is controlled by a relay switch, and some delay in signal on/off might occur.
MP3 / ANDROID /
I-POD/PAD/PHONE
This is the universal input for small devices as Android Phones, MP3 players and products in the Apple family. When connecting by Jack/Jack cable, adjust your portable device to MEDIUM volume. Then adjust the
MP3 volume control to desired level. If too much/little volume, you can gradually adjust the volume control on
your portable device. (Different from device to device).
ON / OFF knap
Main ON/OFF switch !! (Breaks on AC-side !)
CASSETTE
ACCESSORY
DIN-PLUG
If you want to play a cassette tape - or maybe transfer an old tape to USB/SD as MP3 files - this connector is
for your ED-100B Cassette Accessory. Only ONE 7-pin DIN cable is needed. No external power supply. Cable included in ED-100B box. Further editing of the recorded MP3 files should take place on your computer.
HEADPHONES
1 til 7
Connectors for Students Headphones in desired number (max. 7). A load resistor makes it safe to connect
any 8-64Ohms standard headphones. The better the headphone - the better the sound !
Loudspeaker will be active if no headphone is connected to “Master”. (See PHONES).
DIGITAL AMPLIFIER - DIGITAL SWITCH MODE POWER SUPPLY
OUTPUT:: 50W RMS / 100W Music / 200W P.M.P.O.
6,5" full range PA-loudspeaker
SLOT-IN TYPE CD/DVD
CD/VIDEO Player with Mechanical and Electronic Antishock (ESP) - app. 40 sec.
Plays: CD, CD-R , CD-RW, VCD, DVD, DVD-R, DVD-RW, MP3, WMA, MP4, JPG.
USB/SD MMC CARD: MP3, MP4, WMA.
Remote Control of all CD/VIDEO/USB/SD-functions as well as volume.
WARNING !!
This unit must not be opened by unauthorised persons.
Some components might be dangerous to touch.
HIGH TENSION: 230 VAC
Unauthorized disassembly of the unit will cause loss of warranty.
RoHS
UK VERSION
KEYS
Power Supply
SWITCH MODE
Audio Freq. Response
Video Remote Functions
Video Output Phono Plugs
Signal / Noise Ratio
Volume Control
Tone Controls
External Speaker output
Master Headphone output
Relay Controlled
Headphone output
Most important technical specifications
110-240V AC,
Microphone input
100 W max.
20 - 20.000Hz
Line output
Controlled by media used.
MP3 / I-POD Connector
Line input
Composite + Component video
90dB
Closed Speaker system
ENCODER type (Remote)
Weight
Separate Bass & Treble
Cassette Accesory:
6,3mm Mono Jack
Frequency Response
3,5mm Stereo Jack - breaks
Tape Adj.
Internal Loudspeaker
7x 3,5mm Stereo Jack
Size: HxWxD
Weight:
2mV 200 Ohm 6,3 Jack
QUICK
START
GUIDE
200mV 47Kohm Phono
app. 150mV 3,5mm plug
200mV 47Kohm 6,3 mm Jack
6,5” Heavy Duty - Hi-Fi
7,05 kg
Not Included !
60 - 12.500 Hz.
Normal Ferro Typ. 1
VIDEO
STOP
VOL.VOL.+
14,0x21,0x10,0 cm.
1,58 kg
EJECT
PLAY/PAUSE
REV-SKIP-CUE
VIDEO - - - - DVD/VIDEO/JPG- - - - VIDEO
AV35 should be connected to Screen, projector or smartboard with suitable cable (not incl.)
Using COMPOSITE (Yellow) output, picture will be shown in acceptable quality.
Using COMPONENT (Blue/Green/Red) output will show remarkably better picture quality.
Sound will be generated by built-in loudspeaker in AV35 Video.
Turn unit ON - using ”ON / OFF”. Insert DVD record.
DVD will be scanned, and playback starts directly, leaving schreen for language/subtiitles. Default
is the original language and subtitles of the DVD.
Press ”SUB-T” on Remote. Continue single-pressing until relevant language occurs.
If DVD contains different synchronized languages, you can select by pressing AUDIO.
Press STOP to stop playback. Position will be memorized. Playback will continue from here.
Press STOP TWICE to delete memorized point, and playback from start will be possible.
Lowers volume 1dB pr. step. MINIMUM is = 0dB
Increases volume 1dB pr. step. MAXIMUM is = 40dB
(This is NOT an indication of the ACTUAL sound pressure)
Press EJECT, and the CD/DVD will be EJECTED !!!!
PRESS, and playback will be set on PAUSE. Pressing again will resume playback. REMOTE: >||
PANEL and REMOTE: ONE press will jump to next track. Pressing SKIP-REV will jump to previous track.
REMOTE: LONG press on remote keys will cause change of playback speed. Forward/Back
<<REV - CUE>>
PANEL
REMOTE
X
X
X
X
X
X
X
X
X
X
SLOW
X
mal)
ZOOM
ANGLE
N/P
PROGRAM
PLEASE NOTE THAT SAME
BUTTONS CAN HAVE DIFFERENT
FUNCTION DEPENDING ON
WHETHER IT IS SOUND
OR VIDEO PLAYED !
KEYS
QUICKSTART
GUIDE
SOUND
PLAY/PAUSE
STOP
FUNCT
REV-SKIP-CUE
REPEAT
EJECT
MUTE
RANDOM
VOL.VOL.+
0-9
GOTO
REPEAT
SUB-T
AUDIO
OSD
SOUND - - - - -
PLAYBACK OF SOUND - CD/USB/SD - - - - - SOUND
PANEL
REMOTE
0-9
PBC
ARROW-KEYS
MUTE
1. Turn-on the unit by ON/OFF switch - Display shows shortly after ”NO DISC”
2. Insert CD / MP3-CD / WMA-CD - First track is displayed, and playback starts automatically at relatively high volume (30dB). You can now turn volume up/down.
3. Connecting USB-Key, display will change to ”USB” and playback starts.
4. Inserting SD-Card, display will change to ”SD” and playback starts.
5. Pressing FUNC will sequential change between available media.
6. If more media is in playback function, the stop point will be memorized, and playback will continue
from this point when returning to stopped media.
7. UPPER ROW of keys is PRIMARY for audio playback functions, but will also have DVD functions (in
DVD-mode)
8. By connecting the unit to TV/projector, you have extended possibilities of programming the playback. Programming functions are shown on screen.
SETUP
MENU 1
Picture format
and
Signal coding
Press to change between playback and pause. On REMOTE: >||
X
X
Press to STOP playback. Stopping point will be memorized. When pressing PLAY, playback will start
from this point.
Pressing TWICE will cancel the memorized point, and playback from start will take place.
X
X
X
X
X
X
Press SKIP-CUE to jump to next track.
Press SKIP-REW ONE time to play track from start. Press TWICE to jump to previous track.
Default is REPEAT ALL (means: when CD -USB-SD is finished, playback will start over)
Playing CD: By pressing, “REPEAT 1” shows up in display (track is repeated and repeated - - )
USB/SD with MP3/WMA files
Press EJECT, and the CD/DVD will be - - - ejected !!
MENU 3
SOUND
MENU 4
X
Increases the sound level by 1dB pr. step. MAXIMUM is = 40dB (This value doesn’t refer to the ACTUAL sound pressure level !!!)
Direct choice of track number. (Track 47 = 10+ / 4 / 7)
MENU 5
JPG MP4 m.m
X
X
X
X
X
Pressing N/P will switch between different TV-systems: NTSC (USA a.o.) and PAL (Europe a.o.)
Programming a DVD playback is rather complicated, and should only be done by experienced users. This function is therefore not further described. Experienced users will be able to understand
by - experience ! Programming can’t be done without connection to TV/projector.
Pressing GOTO, you can choose which Chapter, time, sequence a.s.o. you want to play. Use ARROW-KEYS on remote. End session by pressing ENTER. (also a complicated operation !)
Pressing REPEAT, you can choose what you want to repeat. REPEAT TITLE id default.
X
X
X
Press repeatedly ”SUB-T” on remote, and select suitable language for subtitles. Limited by DVD.
If DVD contains syncronised languages, press AUDIO, and you can select different languages supported by DVD.
Press OSD and blue status bar will occur in upper part of picture. One more press shows further
information. OSD means “On Screen Display”
For DVD: By pressing you can fill-in required information for GOTO and PROGRAM function.
X
X
Use to navigate in SETUP-menus - and confirm by pressing ENTER.
Press, and the unit will MUTE. One more press, and the sound will be back.
You are advised only to use this function if you are familiar with moving around in menus - or if adjustment are really needed. Next paragraphs tells you how to do - and NOT to do !
1. TV-TYPE: 16:9-formatet is most common nowadays. Try which format that fits your TV / Whiteboard / Projector.
2. PASSWORD: Do not use if not absolutely necessary..
3. RATING: Default: 8-adult, EVERYTHING can be played. 1-KID SAFE will make strict
limitations of what unit will accept to play - if DVD contains this code.
4. RESTORE vælges hvis ALT er gået galt ! (Resetter bl.a. til KINESISK menu !)
5. VIDEO: Default: INTERLACE-YUV ! Choosing S-Video, might cause “BLACK SCREEN”
until you have established a SUPER-VIDEO connection - which can be difficult if not available !
6. TV SYSTEM: Choose AUTO. Pal = Europe / NTSC = USA
1. OSD-LANGUAGE: Choose your language for the OSD information.It’s suggested to choose
ENGLISH.
2. AUDIO LANGUAGE: Please choose by using the REMOTE function.(Shows actual contend of
DVD)
4. MENU LANGUAGE: It’s SUGGESTED to choose a language with Arabic letters !
5. FW VERSION: Information about Firmware version. (for servicing only)
1. AUDIO OUT: Choose SPDIF/OFF (default)
2. KEY: The SPEED of the SOUND can be adjusted up/down - Funny detail, but leave in “0”
A well-known menu for normal LIGHT / CONTRAST / HUE / SATURATION / SHARPEN
X
X
This function is exclusively for VCD format discs.
Picture adjustments adjustments.
Pressing MUTE during playback will mute the SOUND while playback continues in background.
Pressing MUTE again will bring back the sound.
Pressing RANDOM, will cause random playback. One more press will cancel the random function.
Decreases the sound level by 1dB pr. step. MINIMUM is = 0dB
MENU 2
LANGUAGE
X
mal (All zoom positions with sound)
This function is only available if supported by DVD.
X
X
X
X
X
X
X
X
X
X
This menu concerns DIGITAL setup. You are advised to leave it in factory default position.
X
AV35 must be connected to Screen / projector. Loading media with mentioned format will open a
screen menu showing the content. Playback of sequences or individual files can be chosen.
X
Changes in settings involving no picture or sound is considered to be improper operation,
and possible error correction in your suppliers workshop is therefore not covered by any guarantee.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising