TE-TXRX TE-TXRX TE-TXRX TE-TXRX
TE-TXRX
TE-TXRX
Product Manual
Product Manual
TE-TXRX
TE-TXRX
Product Manual
Product Manual
The iBEAM TE-TXRX transmitter and receiver is designed to save time by not
having to run a video cable through a vehicle. The transmitter has a video
and power plug that connects with our iBEAM cameras to make installation a
breeze. The receiver has a standard composite video cable that will plug into
most video screens.
The iBEAM TE-TXRX transmitter and receiver is designed to save time by not
having to run a video cable through a vehicle. The transmitter has a video
and power plug that connects with our iBEAM cameras to make installation a
breeze. The receiver has a standard composite video cable that will plug into
most video screens.
II. Sensor Specifications
II. Sensor Specifications
Transmitting frequency: 2.4 GHz
Input power: 12 VDC
Output signal: PAL/NTSC
Working temperature: -4°F - 176°F
Output power: 100MW
Input signal: PAL/NTSC
Transmission distance: 6m (Max)
Transmitting frequency: 2.4 GHz
Input power: 12 VDC
Output signal: PAL/NTSC
Working temperature: -4°F - 176°F
Output power: 100MW
Input signal: PAL/NTSC
Transmission distance: 6m (Max)
III. Connection
III. Connection
1) The transmitter is designed to mount in the back of the vehicle near the
location of the backup camera.
2) Connect the RED wire of the transmitter to the +12 volt reverse wire.
3) Connect the BLACK wire of the transmitter to a ground (a metal, nonpainted surface).
4) The receiver is designed to go by the video screen up in the dash. It has a
video plug that plugs into the video screen.
5) Connect the RED wire of the receiver to a +12 volt accessory or ignition wire.
6) Connect the BLACK wire of the receiver to a ground (a metal, non-painted surface).
7) Turn the ignition on, turn the video screen on, and put the vehicle in reverse
to test.
1) The transmitter is designed to mount in the back of the vehicle near the
location of the backup camera.
2) Connect the RED wire of the transmitter to the +12 volt reverse wire.
3) C
onnect the BLACK wire of the transmitter to a ground (a metal, nonpainted surface).
4) The receiver is designed to go by the video screen up in the dash. It has a
video plug that plugs into the video screen.
5) Connect the RED wire of the receiver to a +12 volt accessory or ignition wire.
6) Connect the BLACK wire of the receiver to a ground (a metal, non-painted surface).
7) T
urn the ignition on, turn the video screen on, and put the vehicle in reverse
to test.
NOTE: Included is an adapter that will allow for certain iBEAM cameras to
connect to the transmitter based on a traditional or mini 4 pin setup. The
transmitter is water resistant so mounting it underneath a vehicle can be done
NOTE: Included is an adapter that will allow for certain iBEAM cameras to
connect to the transmitter based on a traditional or mini 4 pin setup. The
transmitter is water resistant so mounting it underneath a vehicle can be done
(the closer the transmitter is mounted to the receiver, the better the picture quality will be).
(the closer the transmitter is mounted to the receiver, the better the picture quality will be).
800.221.0932
iBeamUSA.com
800.221.0932
iBeamUSA.com
460 Walker Street
Holly Hill, FL 32117
460 Walker Street
Holly Hill, FL 32117
The iBEAM TE-TXRX transmitter and receiver is designed to save time by not
having to run a video cable through a vehicle. The transmitter has a video
and power plug that connects with our iBEAM cameras to make installation a
breeze. The receiver has a standard composite video cable that will plug into
most video screens.
The iBEAM TE-TXRX transmitter and receiver is designed to save time by not
having to run a video cable through a vehicle. The transmitter has a video
and power plug that connects with our iBEAM cameras to make installation a
breeze. The receiver has a standard composite video cable that will plug into
most video screens.
II. Sensor Specifications
II. Sensor Specifications
Transmitting frequency: 2.4 GHz
Input power: 12 VDC
Output signal: PAL/NTSC
Working temperature: -4°F - 176°F
Output power: 100MW
Input signal: PAL/NTSC
Transmission distance: 6m (Max)
Transmitting frequency: 2.4 GHz
Input power: 12 VDC
Output signal: PAL/NTSC
Working temperature: -4°F - 176°F
Output power: 100MW
Input signal: PAL/NTSC
Transmission distance: 6m (Max)
III. Connection
III. Connection
1) The transmitter is designed to mount in the back of the vehicle near the
location of the backup camera.
2) Connect the RED wire of the transmitter to the +12 volt reverse wire.
3) Connect the BLACK wire of the transmitter to a ground (a metal, nonpainted surface).
4) The receiver is designed to go by the video screen up in the dash. It has a
video plug that plugs into the video screen.
5) Connect the RED wire of the receiver to a +12 volt accessory or ignition wire.
6) Connect the BLACK wire of the receiver to a ground (a metal, non-painted surface).
7) Turn the ignition on, turn the video screen on, and put the vehicle in reverse
to test.
1) The transmitter is designed to mount in the back of the vehicle near the
location of the backup camera.
2) Connect the RED wire of the transmitter to the +12 volt reverse wire.
3) C
onnect the BLACK wire of the transmitter to a ground (a metal, nonpainted surface).
4) The receiver is designed to go by the video screen up in the dash. It has a
video plug that plugs into the video screen.
5) Connect the RED wire of the receiver to a +12 volt accessory or ignition wire.
6) Connect the BLACK wire of the receiver to a ground (a metal, non-painted surface).
7) T
urn the ignition on, turn the video screen on, and put the vehicle in reverse
to test.
NOTE: Included is an adapter that will allow for certain iBEAM cameras to
connect to the transmitter based on a traditional or mini 4 pin setup. The
transmitter is water resistant so mounting it underneath a vehicle can be done
NOTE: Included is an adapter that will allow for certain iBEAM cameras to
connect to the transmitter based on a traditional or mini 4 pin setup. The
transmitter is water resistant so mounting it underneath a vehicle can be done
(the closer the transmitter is mounted to the receiver, the better the picture quality will be).
(the closer the transmitter is mounted to the receiver, the better the picture quality will be).
800.221.0932
iBeamUSA.com
800.221.0932
iBeamUSA.com
460 Walker Street
Holly Hill, FL 32117
460 Walker Street
Holly Hill, FL 32117
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising