IrDA-9000

IrDA-9000
IrDA-9000
UHF 2-Way Synchronizing True Diversity Wireless Microphone
Operation manual
ISO 9001
REGISTERED
INTERNATIONAL
ISO
14001
ISO 14001
REGISTERED
INTERNATIONAL
OHSAS
18001
OHSAS 18001
GREEN PRODUCT
Thank you for choosing this 2-way synchronizing UHF wireless microphone system! This
2-way synchronization is realized by IrDA sensors.
Our products are designed to last and for user friendly operation. Each system consists of:
1. a receiver
2. a handheld or belt-pack transmitter
3. a pair of antennas
4. a switching adaptor
5. an operation manual
For more details, please take a few moments to go through this operating manual to have
a thorough understanding of the functions and operation of both transmitter and receiver.
Parts and functions of IrDA-9000 receiver
Front panel
1
2
6
3
4 5
7
9
8
10
1. Power switch
2. IR sensor area
3. Diversity indicator
4. Radio frequency indicator
5. Audio frequency indicator
6. LCD display
7. UP button
8. DOWN button
9. IrDA synchronization button
10. SET button
Rear panel
11
12
13
14
11. Antenna B socket (TNC)
12. Balanced audio output
13. Unbalanced audio output
14. DC in
15. Antenna A socket (TNC)
-1-
15
ISO 9001|ISO 14001|OHSAS 18001
Changing CHANNEL / FREQUENCY
:
:
A
2-WAY SYNC. TRUE DIVERSITY RECEIVER
B
:
SDR-6200 IrDA
D IV E R S IT Y A U D IO
:
UHF 2-WAY SYNC. TRUE DIVERSITY RECEIVER
POWER
1. Press-release SET button until the CHANNEL-FREQUENCY page appears.
2. Press ▲(UP) or ▼(DOWN) button to select a new channel. As the channel changes, the
frequency changes accordingly, too.
3. After a channel is chosen, wait 5 seconds to store the setting.
CHANNEL scanning
A
2-WAY SYNC. TRUE DIVERSITY RECEIVER
B
SDR-6200 IrDA
D IV E R S IT Y A U D IO
UHF 2-WAY SYNC. TRUE DIVERSITY RECEIVER
POWER
For an interference-free operation, a cleaner channel might be necessary if the current one
receives too much interference. Before scanning, the transmitter must be switched off.
1. Press-release SET button until the AUTO SCAN page appears.
2. Press ▲(UP) or ▼(DOWN) button to find and locate a clear, interference- free channel.
3. After a channel is chosen, wait 5 seconds to store the setting.
CHANNEL SYNCHRONIZING of the receiver and transmitter
< 30cm
Align infrared areas of the receiver and transmitter within 30cm.
A. Changing the receiver’s channel
B. Changing the transmitter’s channel
:
:
:
A
B
▼
D IV E R S IT Y A U D IO
POWER
▼
SDR-6200 IrDA
UHF 2-WAY SYNC. TRUE DIVERSITY RECEIVER
:
:
1. Press the synchronizing button of the
transmitter.
2. The transmitter will synchronize the
receiver’s channel.
1. Press the SYNC button of the receiver.
2. IRDA DATA SEND will appear on the
receiver’s display.
3. Then PLL CHANNEL COPIED BY IRDA will
appear to denote data transferred to denote
successful synchronization.
4. Please try again if IRDA SEND FAIL
appears.
-2-
Adjusting VOLUME level
:
:
A
B
:
D IV E R S IT Y A U D IO
SDR-6200 IrDA
:
UHF 2-WAY SYNC. TRUE DIVERSITY RECEIVER
POWER
1. The setting can be made right on the homepage.
2. Press ▲(UP) or ▼(DOWN) button to choose a new level.
3. After the setting is made, wait 5 seconds to store the setting.
Adjusting SQUELCH level
A
2-WAY SYNC. TRUE DIVERSITY RECEIVER
B
D IV E R S IT Y A U D IO
:
SDR-6200 IrDA
:
UHF 2-WAY SYNC. TRUE DIVERSITY RECEIVER
POWER
When interference is encountered try reducing the sensitivity of the receiver, thus less
susceptible to interference.
1. Press-release SET button until the SQUELCH SETUP page appears.
2. Then press ▲(UP) or ▼(DOWN) button to choose a new level between 1 and 10.
3. After a level is chosen, wait 5 seconds to store the setting.
Since increasing the squelch level will also reduce the reception distance, it’s recommended to
choose the lowest level that can eliminate the interference.
If this still does not solve the problem it means this frequency is not suitable. Adjust the squelch
back to its preset level and use the scan function to locate a clear, interference-free channel.
Receiver installation
1. For best operation, the receiver should be at least 1m above the ground and 1m away from a
wall or metal surface to minimize reflections.
2. The transmitter should also be at least 1m away from a wall or metal surface to minimize
reflections. The transmitter should also be at least 1m away from the receiver.
3. Keep antennas away from noise source such as motors, automobiles, neon light as well as
large metal objects.
-3-
ISO 9001|ISO 14001|OHSAS 18001
Audio output connection
There are two audio outputs on the back of the receiver, Mic-level balanced and Line-level
unbalanced. Use shielded audio cable for the connection between the receiver and the
amplifier/mixer. If the amplifier/mixer has a 1/4"(6.3mm) phone jack, connect a cable from the
1/4"(6.3mm) unbalanced audio output from the receiver to the amplifier/mixer. If the
amplifier/mixer has an XLR input, connect a cable from the balanced XLR audio output from
the receiver to the amplifier/mixer input.
6.3mm phone jack connection
XLR connection
Rack mounting
The receiver can be cabinet-mounted by either one or two units. If only one receiver is to be
mounted, an optional kit is available and it's installed as shown in Fig 1. If two receivers are to
be mounted, they can be assembled by another kit and installed as shown in Fig 2.
Fig 1. Rack mount one receiver
Fig 2. Rack mount two receivers
-4-
UHF handheld microphone(SQ-9000 IrDA)
Parts and functions
1. Cartridge
2. Battery power LED
3. Power switch
4. LCD
5. Menu button
6. Setting button
7. IrDA synchronizing button
8. Battery compartment
9. Color cap
10.IrDA sensor area
11.Charging port
Channel synchronizing of the receiver and microphone
< 30cm
Align infrared areas of the receiver and microphone within 30cm.
A. Changing the receiver’s channel
A
B. Changing the microphone’s channel
B
PLL SEND
IRDA
OK
► PLL CALL ►
D IV E R S IT Y A U D IO
SDR-6200 IrDA
UHF 2-WAY SYNC. TRUE DIVERSITY RECEIVER
POWER
►
CH:00 1
650.000M
►
CH:0 10
652.250M
1. Press the synchronizing button of the
1. Press the synchronizing button of the
microphone.
receiver and the receiver will transmit the
2. IRDA PLL CALL will appear on the
frequency to the microphone and
microphone’s LCD denote synchronizing the synchronize the channels.
receiver’s channel.
2. The microphone's channel will be
3. If the receiver’s channel is synchronized,
synchronized by the receiver.
PLL SEND OK will appear. Otherwise,
please try again if the LCD shows IRDA
FAIL.
If it doesn’t work check that you have the IR sensor panels aligned, that they are facing each
other, devices are within 30cm of each other, and try again.
-5-
ISO 9001|ISO 14001|OHSAS 18001
Battery installation & indicator
This microphone requires 2 x AA batteries to operate.
To install, remove the battery cover and slide the batteries according to the correct polarity into
the battery compartment & replace the battery cover.
Note: Batteries contain a corrosive acid that may leak and damage the microphone when
stored for a long period. Batteries should be removed from the microphone if it is not to be used
for a prolong period of about 4 weeks or more.
When the microphone is switched ON a blue LED② will blink once to indicate the batteries
installed are in good condition. If the LED remains illuminated, it means the batteries are
weak and a replacement is required.
Channel setting
CH:0 10
CH:00 1
1. Use MENU button⑤ to go to the CHANNEL|BATTERY STATUS page.
2. The upper-right channel number will flash to allow changes to be made.
3. Press SET button to change the channel number.
4. 5 seconds after selecting a channel, it will be automatically saved.
Battery type setting
NIMH
AKLN
NIMH
AKLN
1. Use MENU button⑤ to go to the BATTERY TYPE page.
2. Press SET button⑥ for 3 seconds, then the cursor will flash to allow changes to be made.
3. Press SET button to select either NiMH (rechargeable battery) or AKLN (alkaline battery).
4. 5 seconds after selecting a battery type, it will be automatically saved.
Important: NiMH battery must be selected when rechargeable battery is being used. Never
select AKLN (alkaline) when microphone is intended for charging as alkaline battery isn’t
rechargeable. Wrong battery selection will result in battery sensing electronics to display wrong
and misleading status information.
-6-
UHF belt-pack transmitter(SM-9000 IrDA)
Parts and functions
1. Antenna
2. LCD
3. Cover release button
4. Power switch
5. IrDA synchronizing button
6. Menu button
7. Setting button
8. High-impedance gain control (GT)
9. Low-impedance gain control (MT)
10.Battery compartment
11.Audio mute switch
12.Battery power LED
13.IrDA sensor area
14.Mini XLR connector
15.Charging contacts
1
6 7
4
8 9
5
10
2
11 12 14
3
3
13
15
Channel synchronizing of the receiver and transmitter
< 30cm
Align infrared areas of the receiver and transmitter within 30cm.
A. Changing the receiver’s channel
A
B. Changing the transmitter’s channel
B
PLL SEND
IRDA
OK
► PLL CALL ►
D IV E R S IT Y A U D IO
SDR-6200 IrDA
UHF 2-WAY SYNC. TRUE DIVERSITY RECEIVER
POWER
1. Press the synchronizing button of the
transmitter.
2. IRDA PLL CALL will appear on the
transmitter’s LCD denote synchronizing the
receiver’s channel.
3. If the receiver’s channel is synchronized,
PLL SEND OK will appear. Otherwise,
please try again if the LCD shows IRDA
FAIL.
►
CH:00 1
650.000M
►
CH:0 10
652.250M
1. Press the synchronizing button of the
receiver and the receiver will transmit the
frequency to the transmitter and synchronize
the channels.
2. The transmitter's channel will be
synchronized by the receiver.
If it doesn’t work check that you have the IR sensor panels aligned, that they are facing each
other, devices are within 30cm of each other, and try again.
-7-
ISO 9001|ISO 14001|OHSAS 18001
GAIN setting (GT/MT)
Gain control enables the user to set different output levels. GT⑧ is for
the use of instrument with high impedance, such as guitar while MT⑨ is
for the use of low impedance such as lapel or headset microphones.
Battery installation & indicator
This transmitter requires 2 x AA batteries to operate.
To install, remove the battery cover and slide the batteries according to the correct polarity into
the battery compartment⑩ & replace the battery cover.
Note: Batteries contain a corrosive acid that may leak and damage the transmitter when stored
for a long period. Batteries should be removed from the transmitter if it is not to be used for a
prolong period of about 4 weeks or more.
12 will blink once to indicate the batteries
When the transmitter is switched ON a red LED○
installed are in good condition. If the LED remains illuminated, it means the batteries are
weak and a replacement is required.
Channel setting
CH:0 10
CH:00 1
1. Use MENU button⑥ to go to the CHANNEL|BATTERY STATUS page.
2. The upper-right channel number will flash to allow changes to be made.
3. Press SET button to change the channel number.
4. 5 seconds after selecting a channel, it will be automatically saved.
Battery type setting
NIMH
AKLN
NIMH
AKLN
1. Use MENU button⑥ to go to the BATTERY TYPE page.
2. Press SET button⑦ for 3 seconds, then the cursor will flash to allow changes to be made.
3. Press SET button to select either NiMH (rechargeable battery) or AKLN (alkaline battery).
4. 5 seconds after selecting a battery type, it will be automatically saved.
Important: NiMH battery must be selected when rechargeable battery is being used. Never
select AKLN (alkaline) when transmitter is intended for charging as alkaline battery isn’t
rechargeable. Wrong battery selection will result in battery sensing electronics to display wrong
and misleading status information.
-8-
-9-
ISO 9001|ISO 14001|OHSAS 18001
-10-
CHIAYO ELECTRONICS CO.,LTD.
Http://www.chiayo.com.tw|Email: sales@chiayo.com.tw
Office: 30, Lane 27, Section 4, Jen-Ai Road, Taipei 10685, Taiwan|Tel: 886-2-27415741|Fax: 886-2-27525242
Factory: 88, Chung-Hsiao Street 2, Chiayi 60080, Taiwan|Tel: 886-5-2711000|Fax: 886-5-5767611
12I2311
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising