Tecno_Bench_SM-without baseplate_Installation

Tecno_Bench_SM-without baseplate_Installation
TECNO RS SEATING SYSTEM
SURFACE MOUNT WITHOUT BASE PLATE INSTALLATION INSTRUCTIONS
TOOLS NEEDED
MATERIALS INCLUDED
a
b
c
f
d
g
steel wire brush
M12 socket
M16 socket
pencil
h
M8 hex key
e
STEP BY STEP
6mm, 12mm & 18mm
drill bits for concrete
hammer drill
Loctite
M12 hex key
FOR SURFACE MOUNT CYLINDRICAL MOUNTING POST WITHOUT BASE PLATE.
Mark hole locations
Drill holes
Prepare mounting holes
• Using the seat rail as a template, mark
center of each hole location with a
pencil.
• Use hammer drill to drill 5" (125 mm)
deep x 3/4" (18 mm) diameter anchor
hole at each marked location using a
18mm drill bit suitable for concrete
drilling.
• Use compressed air and steel wire brush
to clean each mounting hole.
Note: Ensure seat rail is properly
protected when placing on the ground
surface.
• Drop two resin capsules (a) into each
mounting hole.
NOTE: Forms+Surfaces recommends
starting holes with 6mm diameter drill
bit followed by 12mm and finally 18mm
for maximum accuracy.
T 800.451.0410 | www.forms-surfaces.com
© 2016 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 1 of 4 | Rev. 05-05-16
TECNO RS SEATING SYSTEM
SURFACE MOUNT WITHOUT BASE PLATE INSTALLATION INSTRUCTIONS
STEP BY STEP
FOR SURFACE MOUNT CYLINDRICAL MOUNTING POST WITHOUT BASE PLATE.
c
d
b
Birds-eye view
1/5" MINIMUM
2" MAXIMUM
Break resin capsules
Attach surface mount plate cover
Attach mounting tie rod
• Break capsules with threaded rod (b)
and hammer drill using a M12 socket
attachment.
• Secure centering disc to the surface
using the M16 flat washer (c) and M16
hex nut (d).
• Screw mounting tie rod onto threaded
rod.
• A minimum of 1.5” (38 mm) and
maximum of 2” (51 mm) of the threaded
rod should be above the ground surface.
• Tighten nut until snug.
• Tighten tie rod until snug against hex nut.
• Allow a minimum of 20 minute curing
time before moving on to Step 5.
T 800.451.0410 | www.forms-surfaces.com
© 2016 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 2 of 4 | Rev. 05-05-16
TECNO RS SEATING SYSTEM
SURFACE MOUNT WITHOUT BASE PLATE INSTALLATION INSTRUCTIONS
STEP BY STEP
FOR SURFACE MOUNT CYLINDRICAL MOUNTING POST WITHOUT BASE PLATE.
7
9
8
e
f
g
Attach mounting post
Attach seat rail to mounting post
Secure seat rail
• Slide cylindrical mounting post over tie
rod and centering disc.
• Once all mounting posts are secure,
place seat rail onto rail mounting
brackets. Ensure that connection holes in
the seat rail and mounting brackets align.
• Seat rail should now be secured to the
mounting posts.
• Insert M12 lock washer (g), then M12
x 120 socket head cap screw (f) into
seat rail to secure seat rail to the rail
mounting bracket.
• Tighten screw until snug.
• Fit nylon cap (e) onto the top of socket
head cap screw.
T 800.451.0410 | www.forms-surfaces.com
© 2016 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 3 of 4 | Rev. 05-05-16
TECNO RS SEATING SYSTEM
SURFACE MOUNT WITHOUT BASE PLATE INSTALLATION INSTRUCTIONS
STEP BY STEP
FOR SURFACE MOUNT CYLINDRICAL MOUNTING POST WITHOUT BASE PLATE.
10
10
h
h
h
h
For configurations with backed seats
For configurations with backless seats
• Position backed seat on seat bracket
ensuring that mounting holes line up.
• Position backless seat on seat bracket
ensuring that mounting holes line up.
• Insert M8 x 35 socket head cap screws
(h) using an M8 hex key to secure
backed seat to seat bracket.
• Insert M8 x 35 socket head cap screws
(h) using an M8 hex key to secure
backed seat to seat bracket.
• Tighten screws until snug.
• Tighten screws until snug.
NOTE: Forms+Surfaces recommends
applying Loctite® or similar threadlocking adhesive.
NOTE: Forms+Surfaces recommends
applying Loctite® or similar threadlocking adhesive.
T 800.451.0410 | www.forms-surfaces.com
© 2016 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 4 of 4 | Rev. 05-05-16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising