1689 LED Keypad : User`s Quick Reference Guide - D-tek

1689 LED Keypad : User`s Quick Reference Guide - D-tek
ACCESS CODES
User’s Quick
Reference Guide
ARMING AND DISARMING
To arm
when leaving:
To program Access Codes:
1) Press
To Regular Arm
(Arms entire Area)
2) Enter your [MASTER
CODE]
3) Enter three-digit section
(see Table)
Enter your [ACCESS CODE]*
One-touch Button,
5) Press
to exit
Section:
Codes:
[001]
[002]
[003]
[004] to [047]
[048]
System Master Code
Master Code 1
Master Code 2
User codes 004 to 047
Duress or User code 048
2) Press
3) Press
for each digit in the code
to exit
Light
To arm
when staying:
1689
To Stay Arm
(Arms Area’s perimeter)
One-touch Button,
CODE]
*
?if enabled:
To Instant Arm
(Stay Arms Area, but if any armed zones are
breached, it will instantly cause an alarm)
Stay Arm + press
for 3 seconds
during the Exit Delay.
To Disarm: enter your [ACCESS
PRINTED IN CANADA 02/00 1689EQ-00
Light
?if enabled:
CODE]
Web site: www.paradox.ca
Security Company:
AC
STATUS
The numbers represent
zones 1 to 16. When
illuminated, the zones
are open or breached.
+ Enter your [ACCESS CODE]*
+ Enter your [ACCESS
1) Repeat steps 1 to 3
Lights
Zone Display
(Arms Area without waiting for all
zones to close)
One-touch Button,
To delete Access Codes:
Lights
STAY
?if enabled:
To Force Arm
4) Enter new 4- or 6-digit [CODE]
ARM
* If needed, press button(s)
corresponding to desired partition(s).
ON
OFF
AC LIGHT
= AC power
= Power failure
STATUS LIGHT
Green:
ON
= Zones closed
OFF
= Zone(s) open
FLASH = Exit Delay
STAY LIGHTS
(for Stay & Instant Arming)
STAY 1 for Partition 1
STAY 2 for Partition 2
ON
= Armed
ARM LIGHTS
(for Regular & Force Arming)
ARM1 for Partition 1
ARM2 for Partition 2
ON
= Armed
FLASH = In alarm
FNC1 BUTTON
Your system may have one or more
home automation options. One of
these options may be triggered
directly from the keypad (i.e. reset
smoke detector, activate lights, etc).
Press
for 3 seconds to activate:
ALARM MEMORY DISPLAY
To view the alarms that occurred last
armed period.
ONE-TOUCH BUTTONS
Press & hold a button for 3 seconds
without entering your Access Code.
1) Press
The zones that were in alarm will
illuminate.
The installer must enable each One-touch Button.
2) Press
BYPASS PROGRAMMING
Bypassed zones remain unarmed
when the area is armed.
One-touch Button,
?if enabled:
2) Enter [ACCESS CODE]
If needed, press button(s) to
choose partition(s).
3) Enter the two-digit zone number.
OR
CHIME PROGRAMMING
Keypad beeps when the zone opens.
[2] Wireless Transmitter Battery Low
To Regular Arm: Press & hold
To Stay Arm:
Press & hold
[3] Power Failure
To Force Arm:
Press & hold
[4] Bell/PGM2 Disconnected
To Bypass:
Press & hold
Fast Exit:
When the system is already Stay
Armed, press and hold the button for
3 seconds to start the Exit Delay.
[5] Bell Current Failure
[6] Auxiliary Current Failure
[7] Communication Failure
: Stay Armed after Exit Delay
[8] Timer Loss
Press
and enter time (HH:MM)
: Force Armed after Exit Delay
1) Press
for 3 seconds
2) Enter the two-digit zone numbers
corresponding to the desired
zones.
for Bypass Recall
To re-bypass the zones bypassed
during last armed period.
4) Press
Made a mistake?
Press
To erase entry or revert to last step
[1] No or Low Battery
Press & hold:
1) Press
Press
to exit
TROUBLE LIST
3) Press
to exit
to exit
In Step 3 of Bypass or Step 2 of Chime Programming, re-enter the zone
number to disable the feature.
: Regular Armed after Exit Delay
TROUBLE DISPLAY
When a trouble condition occurs, [TRBL]
symbol will flash and the number(s)
corresponding to the trouble(s) will
illuminate.
1) Press
[9] Tamper/Zone Wiring Failure
Press
to view which zone(s)
[10] Telephone Line Monitoring Failure
[11] Fire Zone Trouble
[12] Module Loss
2) Refer to Trouble List. If no
instructions are given, call
Security Company for repairs.
[13] Wireless Module Supervision Loss
3) Press
[16] Keypad Fault
to exit
Press
to view which zone(s)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement