Dome installation1

Dome installation1
Network Dome Camera
Installation Manual
Installation Manual of Network Camera
2
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly to avoid danger
or property loss.
The precaution measure is divided into ‘Warnings’ and ‘Cautions’:
Warnings: Serious injury or death may be caused if any of these warnings are neglected.
Cautions: Injury or equipment damage may be caused if any of these cautions are neglected.
Warnings Follow these safeguards to Cautions Follow these precautions to
prevent serious injury or death.
prevent potential injury or material
damage.
Warnings:
Please adopt the power adapter which can meet the safety extra low voltage (SELV) standard.
And source with 12 VDC or 24 VAC (depending on models) according to the IEC60950-1 and
Limited Power Source standard.
If the product does not work properly, please contact your dealer or the nearest service center.
Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for
problems caused by unauthorized repair or maintenance.)
To reduce the risk of fire or electrical shock, do not expose this product to rain or moisture.
This installation should be made by a qualified service person and should conform to all the local
codes.
Please install blackouts equipment into the power supply circuit for convenient supply
interruption.
Please make sure that the ceiling can support more than 50(N) Newton gravities if the camera is
fixed to the ceiling.
If the product does not work properly, please contact your dealer or the nearest service center.
Never attempt to disassemble the camera yourself. (We shall not assume any responsibility for
problems caused by unauthorized repair or maintenance.)
Installation Manual of Network Camera
3
Cautions:
Make sure the power supply voltage is correct before using the camera.
Do not drop the camera or subject it to physical shock.
Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of
ethanol and wipe it gently. If the camera will not be used for an extended period of time, put on
the lens cap to protect the sensor from dirt.
Do not aim the camera lens at the strong light such as sun or incandescent lamp. The strong light
can cause fatal damage to the camera.
The sensor may be burned out by a laser beam, so when any laser equipment is being used, make
sure that the surface of the sensor not be exposed to the laser beam.
Do not place the camera in extremely hot, cold temperatures (the operating temperature should
be between -30°C ~ 60°C, or -40°C ~ 60°C if the camera model has an “H” in its suffix ), dusty
or damp environment, and do not expose it to high electromagnetic radiation.
To avoid heat accumulation, good ventilation is required for a proper operating environment.
Keep out of water and any liquid.
While shipping, the camera should be packed in its original packing.
Improper use or replacement of the battery may result in hazard of explosion. Please use the
manufacturer recommended battery type.
For the dome camera that supports IR, you are required to pay attention to the following precautions
to prevent IR reflection:
Dust or grease on the dome cover will cause IR reflection. Please do not remove the dome cover
film until the installation is finished. If there is dus t or grease on the dome cover, clean the dome
cover with clean soft cloth and isopropyl alcohol.
Make certain the installation location does not have reflective surfaces of objects too close to the
camera. The IR light from the camera may reflect back into the lens causing reflection.
The foam ring around the lens (for dome cameras) must be seated flush against the inner surface
of the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to camera body so that
the foam ring and the dome cover are attached seamlessly.
4
Installation Manual of Network Camera
Chapter 1 Dome Camera Installation
1.1 Type I Dome Camera
1.1.1 Camera Description
Figure 1-1 Overview
Table 1-1 Description
No.
Description
1
10M/100M self-adaptive Ethernet interface
2
Reset Button
3
AUDIO OUT: Audio output interface
4
MIC IN: Audio input interface
5
6
7
D+, D-: RS-485 interface
1A, 1B, 2A, 2B: Alarm output interface
IN1, GND, IN2, GND: Alarm input interface
8
Power Supply Interface
Press RESET about 10s when the camera is powering on or rebooting to restore the default settings,
including the user name, password, IP address, port No., etc.
5
Installation Manual of Network Camera
1.1.2 Installation
Ceiling Mounting
Steps:
1. (Optional) use a plier to remove one clip or both two clips (marked in dotted line in Figure 1-2) on
the side of the back box and then route cables through the opening to secure the cables on the
ceiling.
Figure 1-2 Side Clips
2. Drill the screw hole and the cable hole according to the supplied drill template.
1
1
Drill Template
A
Screw hole 1: for Mounting Base
Hole A: for cables routed
through the ceiling
1
1
Code:190600249
Figure 1-3 Drill Template
3. Fix the mounting base to the ceiling; rotate the back box counterclockwise to secure it to the
mounting base; use the lock screw to secure the dome camera.
6
Installation Manual of Network Camera
Figure 1-4 Mounting
4. Loosen the set screws with the hex key (supplied) to remove the bubble.
Figure 1-5 Disassembling
5. Connect the RCA analog video output with a monitor to view the image of the camera. Loosen the
lens set screw to adjust the angle of pan, tilt and rotation direction.
6. Adjust the focus to obtain a perfect image. Fasten the lens set screw.
Figure 1-6 Image Adjusting
7
Installation Manual of Network Camera
Figure 1-7 Image Adjusting
7. Reinstall the bubble and tighten the screws.
Figure 1-8 Reinstall
In-ceiling mounting
Steps:
1. Secure the mounting base to the in-ceiling mounting base with screws.
8
Installation Manual of Network Camera
In-ceiling
Mounting
base
Mounting
Base
Figure 1-9 Mounting Base
2. Push the dome camera to the in-ceiling mounting base, rotate the dome camera for 10 degrees
counterclockwise and then fasten the lock screws to fix the camera.
①
③
②
Lock screw
Figure 1-10 Camera and Mounting Base
3. Cut a 176~180 mm diameter hole in the ceiling and push the dome camera with in-ceiling
mounting base to the hole.
The thickness of the ceiling should be less than 30 mm.
9
Installation Manual of Network Camera
Figure 1-11 Installing
4. It is strongly recommended that you use a safety rope to secure the in-ceiling mounting base to the
roof.
Safety Rope
Figure 1-12 Safety Rope
5. Fasten the lock screws to secure the dome camera.
Lock Screw
Figure 1-13 Fasten Screws
Installation Manual of Network Camera
10
6. Remove the bubble and connect the RCA analog video output with a monitor to view the image of
the camera. Loosen the lens set screw and pan, tilt or rotate the lens to get a desired surveillance
angle. Adjust the lens focus to obtain a perfect image. Fasten the lens set screw. Reinstall the
bubble.
Figure 1-14 Image Adjusting
7. Install the trim plate with screws to finish the installation.
Figure 1-15 Trim Plate Installing
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising