EPSON EB-2265U/EB-2255U/EB-2250U/EB-2245U

EPSON EB-2265U/EB-2255U/EB-2250U/EB-2245U
User's Guide
Contents
2
Notations Used in This Guide
7
Introduction to Your Projector
8
Projector Features.............................................................................. 9
Quick and Easy Setup..................................................................................................................... 9
Easy Wireless Projection ............................................................................................................. 10
Flexible Connectivity.................................................................................................................... 10
Connect with Computers ..................................................................................................... 11
Connect with Mobile Devices............................................................................................. 11
Support for Smooth Meetings.................................................................................................. 11
Projector Parts and Functions ........................................................ 12
Projector Parts - Front.................................................................................................................. 12
Projector Parts - Rear.................................................................................................................... 14
Projector Parts - Base ................................................................................................................... 16
Projector Parts - Control Panel ................................................................................................. 16
Projector Parts - Remote Control ............................................................................................ 17
Setting Up the Projector
20
Connecting to a Composite Video Source..................................................................... 28
Connecting to External USB Devices ..................................................................................... 28
USB Device Projection ........................................................................................................... 29
Connecting to a USB Device ............................................................................................... 29
Disconnecting a USB Device ............................................................................................... 29
Connecting to a Document Camera ...................................................................................... 29
Connecting to an HDBaseT Transmitter .............................................................................. 30
Connecting to External Output Devices............................................................................... 30
Connecting to a VGA Monitor ............................................................................................ 30
Connecting to External Speakers ...................................................................................... 31
Installing Batteries in the Remote Control.................................... 33
Remote Control Operation ........................................................................................................ 33
Opening the Lens Cover .................................................................. 35
Using Basic Projector Features
36
Turning On the Projector ................................................................ 37
Home Screen................................................................................................................................... 38
Turning Off the Projector ................................................................ 40
Setting the Date and Time .............................................................. 41
Projector Placement ........................................................................ 21
Projector Setup and Installation Options............................................................................. 22
Projection Distance....................................................................................................................... 22
Projector Connections ..................................................................... 23
Connecting to a Computer........................................................................................................ 23
Connecting to a Computer for USB Video and Audio............................................... 23
Connecting to a Computer for VGA Video and Audio .............................................. 24
Connecting to a Computer for HDMI Video and Audio ........................................... 25
Connecting to Smartphones or Tablets................................................................................ 25
Connecting to Video Sources ................................................................................................... 26
Connecting to an HDMI Video Source ............................................................................ 26
Connecting to a Component-to-VGA Video Source .................................................. 27
Selecting the Language for the Projector Menus ......................... 43
Projection Modes ............................................................................. 44
Changing the Projection Mode Using the Remote Control.......................................... 44
Changing the Projection Mode Using the Menus ............................................................ 44
Adjusting the Image Height............................................................ 46
Image Shape ..................................................................................... 47
Auto H/V-Keystone ....................................................................................................................... 47
Auto V-Keystone ............................................................................................................................ 47
Automatically Correcting the Image Shape with Screen Fit......................................... 47
Correcting the Image Shape with the Horizontal Keystone Slider............................. 49
Correcting the Image Shape with the Keystone Buttons .............................................. 50
Contents
3
Correcting the Image Shape with Quick Corner ............................................................... 51
Shutting Off the Image and Sound Temporarily .......................... 81
Resizing the Image with the Zoom Ring........................................ 54
Stopping Video Action Temporarily .............................................. 82
Focusing the Image Using the Focus Ring..................................... 55
Zooming Images............................................................................... 83
Selecting an Image Source .............................................................. 56
Using the Remote Control as a Wireless Mouse............................ 84
Image Aspect Ratio .......................................................................... 58
Using the Remote Control as a Pointer.......................................... 86
Changing the Image Aspect Ratio.......................................................................................... 58
Available Image Aspect Ratios ................................................................................................. 58
Projected Image Appearance with Each Aspect Mode .................................................. 59
Saving a User's Logo Image ............................................................ 87
Color Mode ....................................................................................... 60
Projector Identification System for Multiple Projector Control ................................... 89
Setting the Projector ID......................................................................................................... 89
Selecting the Projector You want to Operate .............................................................. 90
Matching the Image Colors ................................................................................................. 91
Adjusting RGBCMY.................................................................................................................. 92
Changing the Color Mode ......................................................................................................... 60
Available Color Modes................................................................................................................. 60
Setting Auto Iris ............................................................................................................................. 60
Adjusting the Image Color .............................................................. 62
Adjusting the Hue, Saturation, and Brightness.................................................................. 62
Adjusting the Gamma ................................................................................................................. 63
Controlling the Volume with the Volume Buttons ....................... 66
Adjusting Projector Features
67
Projecting Two Images Simultaneously ........................................ 68
Unsupported Input Source Combinations for Split Screen Projection..................... 70
Split Screen Projection Restrictions........................................................................................ 70
Projecting a PC Free Presentation.................................................. 71
Supported PC Free File Types................................................................................................... 71
Precautions on PC Free Projection ......................................................................................... 71
Starting a PC Free Slide Show .................................................................................................. 72
Starting a PC Free PDF File Presentation ............................................................................. 73
Starting a PC Free Movie Presentation ................................................................................. 75
PC Free Display Options ............................................................................................................. 76
Controlling a Presentation with Your Hands ................................ 78
Gesture Presenter Restrictions ................................................................................................. 79
Using Multiple Projectors................................................................ 89
Projector Security Features............................................................. 94
Password Security Types ............................................................................................................ 94
Setting a Password.................................................................................................................. 94
Selecting Password Security Types................................................................................... 95
Entering a Password to Use the Projector ..................................................................... 96
Locking the Projector's Buttons............................................................................................... 97
Unlocking the Projector's Buttons .................................................................................... 98
Installing a Security Cable.......................................................................................................... 98
Using the Projector on a Network
99
Wired Network Projection............................................................. 100
Connecting to a Wired Network ........................................................................................... 100
Selecting Wired Network Settings........................................................................................ 100
Wireless Network Projection ........................................................ 103
Installing the Wireless LAN Module..................................................................................... 103
Installing the Wireless LAN Module into the Rear USB-A Port .................................. 104
Selecting Wireless Network Settings Manually ............................................................... 105
Selecting Wireless Network Settings in Windows.......................................................... 108
Contents
4
Selecting Wireless Network Settings in OS X ................................................................... 108
Setting Up Wireless Network Security ................................................................................ 108
Supported Client and CA Certificates............................................................................ 110
Using a QR Code to Connect a Mobile Device ................................................................ 110
Using a USB Key to Connect a Windows Computer...................................................... 111
Wireless Network Projection from a Mobile Device (Screen
Mirroring)........................................................................................ 113
Selecting Screen Mirroring Settings .................................................................................... 113
Connecting Using Screen Mirroring in Windows 10 ..................................................... 115
Connecting Using Screen Mirroring in Windows 8.1 .................................................... 116
Connecting Using Screen Mirroring with the Miracast Function............................. 117
Secure HTTP.................................................................................... 118
Importing a Web Server Certificate Using the Menus .................................................. 118
Supported Web Server Certificates ................................................................................ 119
Monitoring and Controlling the Projector
120
EasyMP Monitor ............................................................................. 121
Controlling a Networked Projector Using a Web Browser ........ 122
Registering Digital Certificates from a Web Browser .................................................... 124
Setting Up Projector Network E-Mail Alerts ............................... 126
Network Projector E-mail Alert Messages ......................................................................... 126
Setting Up Monitoring Using SNMP............................................. 127
Using ESC/VP21 Commands ........................................................ 128
ESC/VP21 Command List ......................................................................................................... 128
Cable Layouts ............................................................................................................................... 129
PJLink Support ............................................................................... 130
Crestron RoomView Support ........................................................ 131
Setting Up Crestron RoomView Support........................................................................... 131
Controlling a Networked Projector Using Crestron RoomView................................ 131
Crestron RoomView Operation Window...................................................................... 132
Crestron RoomView Tools Window................................................................................ 133
Setting Projector Event Schedules ............................................... 135
Adjusting the Menu Settings
138
Using the Projector's Menus ......................................................... 139
Using the On-screen Keyboard..................................................... 140
Available Text Using the On-screen Keyboard................................................................ 140
Image Quality Settings - Image Menu ......................................... 141
Input Signal Settings - Signal Menu............................................. 143
Projector Feature Settings - Settings Menu ................................ 145
Projector Setup Settings - Extended Menu ................................. 147
Projector Network Settings - Network Menu.............................. 150
Network Menu - Screen Mirroring Settings ...................................................................... 151
Network Menu - Basic Menu .................................................................................................. 152
Network Menu - Wireless LAN Menu .................................................................................. 153
Network Menu - Wired LAN Menu ....................................................................................... 155
Network Menu - Notifications Menu ................................................................................... 156
Network Menu - Others Menu ............................................................................................... 157
Network Menu - Reset Menu.................................................................................................. 158
Projector Setup Settings - ECO Menu .......................................... 159
Projector Information Display - Info Menu ................................. 161
Info Menu - Projector Info Menu .......................................................................................... 161
Event ID Code List................................................................................................................. 162
Projector Reset Options - Reset Menu ......................................... 164
Copying Menu Settings Between Projectors (Batch Setup) ...... 165
Transferring Settings From a USB Flash Drive ................................................................. 165
Transferring Settings From a Computer ............................................................................ 166
Batch Setup Error Notification ......................................................................................... 167
Contents
Maintaining the Projector
5
168
Cleaning the Lens........................................................................... 169
Cleaning the Projector Case.......................................................... 170
Air Filter and Vent Maintenance .................................................. 171
Cleaning the Air Filter and Vents.......................................................................................... 171
Replacing the Air Filter ............................................................................................................. 171
Projector Lamp Maintenance ....................................................... 173
Replacing the Lamp ................................................................................................................... 174
Resetting the Lamp Timer ....................................................................................................... 179
Replacing the Remote Control Batteries ..................................... 180
Solving Problems
181
Projection Problems ...................................................................... 182
Projector Indicator Status ............................................................. 183
Using the Projector Help Displays................................................ 185
Solving Image or Sound Problems............................................... 186
Solutions When No Image Appears..................................................................................... 186
Solutions When Image is Incorrect Using the USB Display Function ..................... 187
Solutions When "No Signal" Message Appears ............................................................... 187
Displaying From a Laptop.................................................................................................. 187
Displaying From a Mac Laptop........................................................................................ 188
Solutions When "Not Supported" Message Appears .................................................... 188
Solutions When Only a Partial Image Appears................................................................ 188
Solutions When the Image is not Rectangular ................................................................ 188
Solutions When the Image Contains Noise or Static..................................................... 189
Solutions When the Image is Fuzzy or Blurry .................................................................. 189
Solutions When the Image Brightness or Colors are Incorrect ................................. 190
Solutions to Sound Problems................................................................................................. 190
Solutions When Image File Names are not Displayed Correctly in PC Free......... 191
Solving Projector or Remote Control Operation Problems ....... 192
Solutions to Projector Power or Shut-Off Problems...................................................... 192
Solutions to Problems with the Remote Control............................................................ 192
Solutions to Password Problems........................................................................................... 193
Solution When "The Battery that Saves Your Clock Settings is Running Low"
Message Appears........................................................................................................................ 193
Solutions to Gesture Presenter Problems.......................................................................... 193
Solving Network Problems ........................................................... 194
Solutions When Wireless Authentication Fails ................................................................ 194
Solutions When You Cannot Access the Projector Through the Web ................... 194
Solutions When Network Alert E-Mails are not Received............................................ 194
Solutions When the Image Contains Static During Network Projection............... 195
Solutions When You Cannot Connect Using Screen Mirroring................................. 195
Solutions When the Image or Sound Contains Static During Screen Mirroring
Connection .................................................................................................................................... 195
Appendix
197
Optional Accessories and Replacement Parts............................. 198
Screens............................................................................................................................................ 198
Cables .............................................................................................................................................. 198
Mounts ............................................................................................................................................ 198
For Wireless Connection .......................................................................................................... 198
External Devices .......................................................................................................................... 199
Replacement Parts...................................................................................................................... 199
Screen Size and Projection Distance............................................ 200
Supported Monitor Display Resolutions ..................................... 204
Projector Specifications ................................................................ 206
Connector Specifications ......................................................................................................... 207
External Dimensions ...................................................................... 209
USB Display System Requirements .............................................. 210
List of Safety Symbols (corresponding to IEC60950-1 A2) ........ 211
Contents
Glossary .......................................................................................... 213
Notices ............................................................................................ 215
FCC Compliance Statement.................................................................................................... 215
Indication of the manufacturer and the importer in accordance with
requirements of EU directive.................................................................................................. 216
Wireless Telegraphy Act Regulations.................................................................................. 216
Restriction of Use ........................................................................................................................ 216
Operating System References................................................................................................ 216
Trademarks.................................................................................................................................... 216
Copyright Notice......................................................................................................................... 217
Copyright Attribution................................................................................................................ 217
6
Notations Used in This Guide
Safety Symbols
The projector and its manuals use graphical symbols and labels to indicate content that tells you how to use the projector safely.
Read and carefully follow the instructions that are marked with these symbols and labels to avoid injury to persons or damage to property.
Warning
Caution
This symbol indicates information that, if ignored, could possibly result in personal injury or even death.
This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.
General Information Notations
This label indicates procedures that may result in damage or injury if sufficient care is not taken.
Attention
This label indicates additional information that may be useful to know.
[Button name]
Menu/Setting name
Indicates the name of the buttons on the remote control or the control panel.
Example: [Esc] button
Indicates projector menu and setting names.
Example:
Select the Image menu
s Image > Advanced
This label indicates links to the related pages.
s
This label indicates a page where detailed information regarding a topic can be found.
Introduction to Your Projector
Refer to these sections to learn more about your projector's features and part names.
g Related Links
• "Projector Features" p.9
• "Projector Parts and Functions" p.12
Projector Features
This projector comes with this special features. Refer to these sections for
more details.
9
• Horizontal keystone slider allows you to quickly correct horizontal
distortion in the projected image (EB-2140W/EB-2040).
g Related Links
• "Quick and Easy Setup" p.9
• "Easy Wireless Projection" p.10
• "Flexible Connectivity" p.10
• "Support for Smooth Meetings" p.11
Quick and Easy Setup
• Direct Power On feature to turn on the projector as soon as you plug it in.
• Auto Power On feature to turn on the projector when the projector detects
an image signal from the port you specified as the Auto Power On source.
• Home screen feature to easily select an input source and useful functions.
• Real-time, automatic vertical and horizontal keystone correction always
displays a rectangular screen (Auto H/V-Keystone) (EB-2265U/EB2255U/EB-2250U/EB-2245U/EB-2165W/EB-2155W/EB-2065/EB-2055/EBX550KG/EB-X500KG).
• Automatic vertical keystone correction always displays a rectangular screen
(Auto V-Keystone) (EB-2140W/EB-2040).
• Screen Fit feature to automatically resize projected images (EB-2265U/EB2255U/EB-2250U/EB-2245U/EB-2165W/EB-2155W/EB-2065/EB-2055/EBX550KG/EB-X500KG).
• Focus Help feature to guide you to the optimum focus adjustment (EB2265U/EB-2255U/EB-2250U/EB-2245U/EB-2165W/EB-2155W/EB2065/EB-2055/EB-X550KG/EB-X500KG).
g Related Links
• "Auto H/V-Keystone" p.47
• "Projector Setup Settings - Extended Menu" p.147
• "Turning On the Projector" p.37
• "Automatically Correcting the Image Shape with Screen Fit" p.47
• "Focusing the Image Using the Focus Ring" p.55
• "Correcting the Image Shape with the Horizontal Keystone Slider" p.49
Projector Features
Easy Wireless Projection
10
See the EasyMP Multi PC Projection Operation Guide for details.
• Screen Mirroring to connect your projector and mobile device wirelessly
using Miracast technology (EB-2265U/EB-2255U/EB-2165W).
• Epson iProjection to connect your projector and mobile device wirelessly
using the app available on App Store or Google play.
a
Any fees incurred when communicating with App Store or Google
play are the responsibility of the customer.
• EasyMP Multi PC Projection to project up to four images at the same time
by splitting the projected screen. You can project images from computers
on the network, or from smartphones or tablet devices on which Epson
iProjection is installed.
a
• When projecting images using a wireless LAN, you must install the
Epson 802.11b/g/n wireless LAN module, and then set up your
projector and computer for wireless projection. The Epson
802.11b/g/n wireless LAN module may not be included with your
projector.
• You can download the necessary software and manuals from the
following Web site:
http://www.epson.com/
g Related Links
• "Using the Projector on a Network" p.99
Flexible Connectivity
This projector supports a wide variety of easy-to-use connectivity options as
shown below.
Projector Features
g Related Links
• "Connect with Computers" p.11
• "Connect with Mobile Devices" p.11
Connect with Computers
Connect with one USB cable to project images and output audio (USB
Display).
11
Support for Smooth Meetings
The Gesture Presenter feature allows you to control your presentation using
your hands allowing you to give presentations in front of the screen without a
presentation remote control (EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG).
g Related Links
• "Connecting to a Computer for USB Video and Audio" p.23
Connect with Mobile Devices
• HDMI1/MHL port to connect an MHL cable to the mobile device and to
the projector.
g Related Links
• "Controlling a Presentation with Your Hands" p.78
g Related Links
• "Connecting to Smartphones or Tablets" p.25
Projector Parts and Functions
The following sections explain the projector parts and their functions.
All of the features in this guide are explained using illustrations of EB-2265U
unless otherwise mentioned.
g Related Links
• "Projector Parts - Front" p.12
• "Projector Parts - Rear" p.14
• "Projector Parts - Base" p.16
• "Projector Parts - Control Panel" p.16
• "Projector Parts - Remote Control" p.17
Projector Parts - Front
EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB-2165W
12
EB-2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG
Projector Parts and Functions
EB-2140W/EB-2040
13
Name
Function
Caution
While projecting, do not put your face or
hands near the air exhaust vent, and do not
place objects that may become warped or
damaged by heat near the vent. Hot air from
the air exhaust vent could cause burns,
warping, or accidents to occur.
Name
A
Air exhaust vent
Function
B
A/V Mute slide lever
Slide the lever to open and close the A/V mute slide.
C
Foot release lever
Press the foot release lever to extend and retract the
front adjustable foot.
D
Front adjustable foot
When setup on a surface such as a desk, extend the foot
to adjust the position of the image.
E
A/V Mute slide
Close when not using the projector to protect the lens.
By closing during projection you can hide the image
and the sound.
F
Remote receiver
Receives signals from the remote control.
G
Sensor (EBSensor for detecting the projected images.
2265U/EB-2255U/EB2250U/EB-2245U/EB2165W/EB2155W/EB-2065/EB2055/EBX550KG/EBX500KG)
H
Wireless LAN
Indicates the access status of the supplied or optional
indicator (EBwireless LAN module.
2265U/EB-2255U/EB2250U/EB-2245U/EB2165W/EB2155W/EB-2065/EB2055/EBX550KG/EBX500KG)
I
Air intake vent (air
filter)
Exhaust vent for air used to cool the projector
internally.
Warning
Do not look into the vents. If the lamp
explodes, gases may escape and small
fragments of glass may be scattered which
could cause an injury. Contact a doctor if any
fragments of broken glass are inhaled or get
into the eyes or mouth.
Takes in air to cool the projector internally.
Projector Parts and Functions
Name
Function
J
Air filter cover latch
Use this latch to open the air filter cover.
K
Illumination sensor
Detects the brightness of the surroundings to optimize
(EB-2265U/EBthe lamp brightness.
2255U/EB-2250U/EB2245U/EB2165W/EB2155W/EB-2065/EB2055/EBX550KG/EBX500KG)
L
Control panel
Operates the projector.
M
[Focus Help] button Projects the Focus Help screen to fine-tune your focus
(EB-2265U/EBadjustments.
2255U/EB-2250U/EB2245U/EB2165W/EB2155W/EB-2065/EB2055/EBX550KG/EBX500KG)
N
Zoom ring
Adjusts the image size.
O
[Screen Fit] button
(EB-2265U/EB2255U/EB-2250U/EB2245U/EB2165W/EB2155W/EB-2065/EB2055/EBX550KG/EBX500KG)
Performs Screen Fit feature to automatically correct the
shape and position of images to fit on your screen.
Hold down for three seconds to display the menu for
the Gesture Presenter feature.
P
Focus ring
Adjusts the image focus.
Q
Lamp cover
Open when replacing the projector's lamp.
R
Indicators
Indicates the projector's status.
S
Horizontal keystone
slider (EB2140W/EB-2040)
Corrects horizontal distortion in the projected image.
14
g Related Links
• "Projector Indicator Status" p.183
• "Resizing the Image with the Zoom Ring" p.54
• "Focusing the Image Using the Focus Ring" p.55
• "Automatically Correcting the Image Shape with Screen Fit" p.47
• "Correcting the Image Shape with the Horizontal Keystone Slider" p.49
Projector Parts - Rear
EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB-2165W/EB-2155W/EB2065/EB-2055/EB-X550KG/EB-X500KG
Projector Parts and Functions
EB-2140W/EB-2040
Name
Name
Function
A
Computer1 port
Inputs image signals from a computer and component
video signals from other video sources.
B
RS-232C port
Connects an RS-232C cable to control the projector
from a computer. (You do not need to use this port
normally.)
C
D
Audio 1 port
Computer2/Monitor
Out port
15
Inputs audio from equipment connected to the
Computer1 port.
When Monitor Out Port is set to Monitor Out in the
projector's Extended menu, analog RGB signals input
from the Computer1 port are output to an external
monitor. You cannot output signals input from other
ports or component video signals.
When Monitor Out Port is set to Computer2 in the
projector's Extended menu, image signals from a
computer and component video signals from other
video sources are input.
s Extended > Operation > Monitor Out Port
E
Audio 2 port
Inputs audio from equipment connected to the
Computer2 port.
F
Audio Out port
Outputs audio from the current input source to an
external speaker.
Function
G
Power inlet
Connects the power cord to the projector.
H
L-Audio-R ports
Inputs audio from equipment connected to the Video
port.
I
Security slot
The security slot is compatible with the Microsaver
Security System manufactured by Kensington.
J
Remote receiver
Receives signals from the remote control.
K
HDBaseT port (EB2265U/EB-2165W)
Connects a LAN cable to the optional HDBaseT
Transmitter.
L
HDMI2 port
Inputs video signals from HDMI compatible video
equipment and computers.
This projector is compatible with HDCP.
M
HDMI1/MHL port
Inputs video signals from HDMI compatible video
equipment and computers, or MHL (Mobile HighDefinition Link) compatible mobile devices.
This projector is compatible with HDCP.
N
Video port
Inputs composite video signals from video sources.
O
USB-B port
Connects a USB cable to the computer to project
computer images, to use the Wireless Mouse function,
or to use the Gesture Presenter feature.
P
USB-A port
Connects a USB memory device or a digital camera
and projects PDFs, movies, or images using PC Free.
Connects the optional Document Camera.
Connects the wireless LAN module (EB-2140W/EB2040).
Q
LAN port
Connects a LAN cable to connect to a network.
R
Wireless LAN module Secures the wireless LAN module cover.
fixing screw (EB2140W/EB-2040)
g Related Links
• "Using the Remote Control as a Wireless Mouse" p.84
• "Installing a Security Cable" p.98
• "Projecting a PC Free Presentation" p.71
Projector Parts and Functions
Projector Parts - Base
16
g Related Links
• "Installing a Security Cable" p.98
Projector Parts - Control Panel
Name
Name
Function
A
Ceiling mount fixing
points (three points)
Attach the optional ceiling mount here when
suspending the projector from a ceiling.
B
Security cable
attachment point
Pass a commercially available wire lock through here
and lock it in place.
C
Rear feet
When setup on a surface such as a desk, turn to extend
and retract to adjust the horizontal tilt.
D
Front adjustable foot
When setup on a surface such as a desk, extend the foot
to adjust the position of the image.
Function
A
Power button
Turns the projector on or off.
B
[Home] button
Displays and closes the Home screen.
C
[Source Search]
button
Changes to the next input source.
D
[Enter] button [
E
Keystone adjustment
buttons and arrow
buttons
]
Enters the current selection and moves to the next level
while displaying the projector's menu or help.
Optimizes Tracking, Sync., and Position in the
projector's Signal menu while projecting an analog
RGB signal from the Computer1 or Computer2 port.
Displays the Keystone screen allowing you to correct
keystone distortion.
Selects menu items while displaying the projector's
menu or help.
Projector Parts and Functions
Name
Function
F
[Esc] button
Stops the current function.
Moves back to the previous menu level while
displaying the projector's menu.
G
Volume buttons and
arrow buttons
Adjusts the speaker volume.
Selects menu items while displaying the projector's
menu or help.
H
[Menu] button
Displays and closes the projector's menu.
g Related Links
• "Input Signal Settings - Signal Menu" p.143
• "Home Screen" p.38
• "Correcting the Image Shape with the Keystone Buttons" p.50
17
Projector Parts - Remote Control
Projector Parts and Functions
Name
18
Function
Name
Function
A
Power button
Turns the projector on or off.
O
[A/V Mute] button
Turns the video and audio on or off temporarily.
B
[Computer] button
Switches the image source between the Computer1 and
Computer2 ports.
P
[Split] button
Projects two images from different image sources
simultaneously by splitting the projected screen.
C
[HDMI/Video]
button
Switches the image source between the Video input
port and HDMI input port.
Switches the image source from the HDBaseT input
port (EB-2265U/EB-2165W).
Q
[Home] button
Displays and closes the Home screen.
R
[Freeze] button
Pauses or resumes images.
S
[Volume] up/down
buttons
Adjusts the speaker volume.
T
[Pointer] button
Displays the on-screen pointer.
U
[Esc] button
Stops the current function.
Moves back to the previous menu level while
displaying the projector's menu.
Acts as a mouse's right button when using the Wireless
Mouse function.
V
[ID] button
Hold down this button and press the numeric buttons
to select the ID for the projector you want to operate
using the remote control.
W
[Color Mode] button
Changes the color mode.
X
[Link Menu] button
Displays the settings menu for the device linked to the
projector's HDMI port.
Y
[Gesture] button (EB- Displays the menu for the Gesture Presenter feature.
2265U/EB-2255U/EB2250U/EB-2245U/EB2165W/EB2155W/EB-2065/EB2055/EBX550KG/EBX500KG)
Z
[LAN] button
Swithces the image source between the network
connected devices.
a
[USB] button
Swithces the image source between the USB Display
and USB-A port.
b
[Source Search]
button
Swithces to the next input source.
D
[Screen Fit] button
Performs Screen Fit feature to automatically correct the
shape and position of images to fit on your screen.
E
Numeric buttons
Enters numbers in the projector's menu while holding
down the [Num] button.
F
[Auto] button
Optimizes Tracking, Sync., and Position in the
projector's Signal menu while projecting an analog
RGB signal from the Computer1 or Computer2 port.
G
[Aspect] button
Changes the aspect mode.
H
[Num] button
Hold down this button to enter numbers using the
numeric buttons.
I
[Menu] button
Displays and closes the projector's menu.
J
Arrow buttons
Selects menu items while displaying the projector's
menu or help.
K
[Enter] button [
L
[User] button
Performs settings assigned in the User Button setting
in the projector's Settings menu.
M
[Page] up/down
buttons
Controls page up and down on your computer when
you connect a projector and computer using a USB
cable or over the network.
Displays the previous or next screen while using the PC
Free feature.
N
[E-Zoom] +/–
buttons
]
Enters the current selection and moves to the next level
while displaying the projector's menu or help.
Acts as a mouse's left button when using the Wireless
Mouse function.
Zooms in or zooms out the image area.
Projector Parts and Functions
Name
c
Remote control light
emitting area
Function
Outputs remote control signals.
g Related Links
• "Image Aspect Ratio" p.58
• "Color Mode" p.60
• "Input Signal Settings - Signal Menu" p.143
• "Projector Setup Settings - Extended Menu" p.147
• "Home Screen" p.38
• "Automatically Correcting the Image Shape with Screen Fit" p.47
• "Using the Remote Control as a Wireless Mouse" p.84
• "Projecting Two Images Simultaneously" p.68
• "Using the Remote Control as a Pointer" p.86
• "Connecting to a Computer for USB Video and Audio" p.23
• "Controlling a Presentation with Your Hands" p.78
• "Projecting a PC Free Presentation" p.71
• "Using the Projector on a Network" p.99
19
Setting Up the Projector
Follow the instructions in these sections to set up your projector.
g Related Links
• "Projector Placement" p.21
• "Projector Connections" p.23
• "Installing Batteries in the Remote Control" p.33
• "Opening the Lens Cover" p.35
Projector Placement
You can place the projector on almost any flat surface to project an image.
You can also install the projector in a ceiling mount if you want to use it in a
fixed location. An optional ceiling mount is required when suspending the
projector from a ceiling.
Note the following points when selecting a projector location:
• Place the projector on a sturdy, level surface or install it using a compatible
mount.
• Leave plenty of space around and under the projector for ventilation, and
do not place it on top of or next to anything that could block the vents.
• Position the projector within reach of a grounded electrical outlet or
extension cord.
• Place the projector parallel to the screen.
21
a
If you cannot install the projector parallel to the screen, correct
keystone distortion using the projector controls.
Warning
• You must install a ceiling mount when suspending the projector from a ceiling.
If you do not install the projector correctly, it could fall and cause damage or
injury.
• Do not use adhesives on the ceiling mount fixing points to prevent the screws
from loosening, or use lubricants, oils, or similar substances on the projector; the
projector case may crack causing it to fall from its ceiling mount. This could
cause serious injury to anyone under the ceiling mount and could damage the
projector.
• Do not cover the projector's air intake or air exhaust vents. If the vents are
covered, the internal temperature could rise and cause a fire.
• Do not install the projector on an unstable surface or in a location beyond the
weight specifications of the projector. Otherwise, it could fall or topple causing
an accident and injury.
• When installing the projector in a high position, take measures to prevent falling
by using wires to ensure safety in an emergency, such as an earthquake, and to
prevent accidents. If it is not installed correctly, it could fall causing an accident
and injury.
Attention
• Do not operate the projector on its side. This may cause the projector to
malfunction.
• If you are using the projector at altitudes above 1500 m, set the High Altitude
Mode setting to On in the projector's Extended menu to ensure the projector's
internal temperature is regulated properly.
s Extended > Operation > High Altitude Mode
• Try not to setup the projector in locations subject to high humidity and dust, or
in locations subject to smoke from fires or tobacco smoke.
g Related Links
• "Projector Setup and Installation Options" p.22
• "Projection Distance" p.22
• "Image Shape" p.47
• "Projector Setup Settings - Extended Menu" p.147
Projector Placement
Projector Setup and Installation Options
You can set up or install your projector in the following ways:
Front/Rear
22
projector is from the screen, but can vary depending on the zoom factor,
aspect ratio, and other settings.
See the Appendix for details about how far to place the projector from the
screen based on the size of the projected image.
a
When correcting keystone distortion, your image is slightly smaller.
Front Ceiling/Rear Ceiling
g Related Links
• "Screen Size and Projection Distance" p.200
Make sure you select the correct Projection option in the projector's
Extended menu according to the installation method being used.
g Related Links
• "Projection Modes" p.44
Projection Distance
The distance at which you place the projector from the screen determines the
approximate size of the image. The image size increases the farther the
Projector Connections
You can connect the projector to a variety of computer, video, and audio
sources to display presentations, movies, or other images, with or without
sound.
Attention
Check the shape and orientation of the connectors on any cable you plan to
connect. Do not force a connector into a port if it does not fit. The device or your
projector could be damaged or could malfunction.
a
See the Quick Start Guide for a list of cables supplied with your
projector. Purchase optional or commercially available cables when
necessary.
• Connect a computer that has a USB port, standard video output (monitor)
port, or HDMI port.
• For video projection, connect devices such as DVD players, gaming
consoles, digital cameras, and smartphones with compatible video output
ports.
• If your presentation or video includes sound, you can connect audio input
cables.
• For slide shows or presentations without a computer, you can connect USB
devices (such as a flash drive or camera) or the optional Epson document
camera.
23
Connecting to a Computer
Follow the instructions in these sections to connect a computer to the
projector.
g Related Links
• "Connecting to a Computer for USB Video and Audio" p.23
• "Connecting to a Computer for VGA Video and Audio" p.24
• "Connecting to a Computer for HDMI Video and Audio" p.25
Connecting to a Computer for USB Video and Audio
If your computer meets the system requirements, you can send video and
audio output to the projector through the computer's USB port. This function
is called USB Display. Connect the projector to your computer using a USB
cable.
a
• If you use a USB hub, the connection may not operate correctly.
Connect the USB cable directly to the projector.
a Connect the cable to your projector's USB-B port.
g Related Links
• "Connecting to a Computer" p.23
• "Connecting to Smartphones or Tablets" p.25
• "Connecting to Video Sources" p.26
• "Connecting to External USB Devices" p.28
• "Connecting to a Document Camera" p.29
• "Connecting to an HDBaseT Transmitter" p.30
• "Connecting to External Output Devices" p.30
b Connect the other end to any available USB port on your computer.
c Turn on the projector and your computer.
Projector Connections
d Do one of the following to install the Epson USB Display software:
a
You only need to install this software the first time you connect
the projector to the computer.
• Windows: Select Run EMP_UDSE.EXE in the dialog box that is
displayed to install the Epson USB Display software.
• OS X: The Epson USB Display setup folder is displayed on your
screen. Select USB Display Installer and follow the on-screen
instructions to install the Epson USB Display software. If the USB
Display Setup folder is not displayed automatically, double-click
EPSON_PJ_UD > USB Display Installer.
any on-screen instructions.
e Follow
Do not disconnect the USB cable or turn off the projector until the
projector displays an image.
The projector displays the image from your computer's desktop and outputs
sound if your presentation contains audio.
a
• If the projector does not project any images, do one of the following:
• Windows: Click All Programs > EPSON Projector > Epson USB
Display > Epson USB Display Ver.x.xx.
• OS X: Double-click the USB Display icon in the Application
folder.
• When you finish projection, do one of the following:
• Windows: Disconnect the USB cable. You do not need to operate
Safely Remove Hardware.
• OS X: Select Disconnect from the USB Display icon menu on the
menu bar or Dock, and then disconnect the USB cable.
g Related Links
• "USB Display System Requirements" p.210
24
Connecting to a Computer for VGA Video and Audio
You can connect the projector to your computer using a VGA computer
cable.
You can play sound through the projector's speaker system by connecting a
commercially available 3.5 mm stereo mini-jack audio cable.
a
• To connect a Mac that does not have a VGA video port, you need an
adapter that allows you to connect to the projector's VGA video port.
• To project an image source connected to the Computer2/Monitor
Out port, set Monitor Out Port to Computer2 in the projector's
Extended menu.
s Extended > Operation > Monitor Out Port
• Make sure the audio cable is labeled "No resistance".
a Connect the VGA computer cable to your computer's monitor port.
b Connect the other end to a Computer port on the projector.
c Tighten the screws on the VGA connector.
the audio cable to your laptop's headphone or audio-out jack,
d Connect
or your desktop's speaker or audio-out port.
Projector Connections
the other end to the Audio port that corresponds to the
e Connect
Computer port you are using.
g Related Links
• "Projector Setup Settings - Extended Menu" p.147
25
b Connect the other end to the projector's HDMI port.
a
Connecting to a Computer for HDMI Video and Audio
If your computer has an HDMI port, you can connect it to the projector using
an HDMI cable and send the computer's audio with the projected image.
a
To connect a Mac that does not have an HDMI port, you need an
adapter that allows you to connect to the projector's HDMI port.
Contact Apple for compatible adapter options. Older Mac computers
(2009 and earlier) may not support audio through the HDMI port.
a Connect the HDMI cable to your computer's HDMI output port.
If you have problems hearing audio through the HDMI connection,
connect one end of a commercially available 3.5 mm stereo mini-jack
audio cable to the projector's Audio port and the other end to your
computer's audio out port. Select the audio input port you connected
to in the projector's Extended menu.
s Extended > A/V Settings > HDMI1 Audio Output
s Extended > A/V Settings > HDMI2 Audio Output
g Related Links
• "Projector Setup Settings - Extended Menu" p.147
Connecting to Smartphones or Tablets
You can connect the projector to smartphones and tablets using a MHL cable
and send the audio with the projected image.
a
• You may not be able to project correctly, depending on the model
and settings of the smartphone or tablet.
• You may not be able to connect an MHL cable to all devices. Contact
the manufacturer of your smartphone or tablet device to check if
your device supports MHL.
Projector Connections
a Connect the MHL cable to your device's Micro-USB port.
b Connect the other end to the projector's HDMI1/MHL port.
26
Connecting to Video Sources
Follow the instructions in these sections to connect video devices to the
projector.
a
Attention
If you connect an MHL cable that does not support the MHL standards, the
smartphone or tablet device may become hot, or leakage or explosion may
happen.
• If the port on the device you connect has an unusual shape, use the
cable supplied with the device or an optional cable to connect to the
projector.
• The cable differs depending on the output signal from the connected
video devices.
• Some video devices are capable of outputting different types of
signals. See your video device manual to confirm what type of signals
can be output.
g Related Links
• "Connecting to an HDMI Video Source" p.26
• "Connecting to a Component-to-VGA Video Source" p.27
• "Connecting to a Composite Video Source" p.28
Connecting to an HDMI Video Source
The connected smartphone or tablet begins charging when images are
projected. If you connect using a MHL-HDMI conversion adapter,
charging the smartphone or tablet device may not work or you may not
be able to perform operations using the projector's remote control.
a
a
• Charging may not work when using a lot of power, such as
when playing a movie.
• Charging does not work when the projector is in standby mode
or the battery in a smartphone or tablet is depleted.
If images are not projected correctly, disconnect and then reconnect
the MHL cable.
If your video source has an HDMI port, you can connect it to the projector
using an HDMI cable and send the image source's audio with the projected
image.
Attention
Do not turn on the video source before connecting it to the projector. Doing so
could damage the projector.
a Connect the HDMI cable to your video source's HDMI output port.
Projector Connections
b Connect the other end to the projector's HDMI port.
27
a
• To project an image source connected to the Computer2/Monitor
Out port, set Monitor Out Port to Computer2 in the projector's
Extended menu.
s Extended > Operation > Monitor Out Port
• You can also set the port used for audio input in the projector's
Extended menu.
s Extended > A/V Settings > Audio Output
• Make sure the audio cable is labeled "No resistance".
the component connectors to your video source's color-coded
a Connect
component video output ports.
a
If you have problems hearing audio through the HDMI connection,
connect one end of a commercially available 3.5 mm stereo mini-jack
audio cable to the projector's Audio port and the other end to your
video source's audio out port. Select the audio input port you
connected to in the projector's Extended menu.
s Extended > A/V Settings > HDMI1 Audio Output
s Extended > A/V Settings > HDMI2 Audio Output
a
The ports usually labeled Y, Pb, Pr or Y, Cb, Cr. If you are using
an adapter, connect these connectors to your component video
cable.
b Connect the VGA connector to a Computer port on the projector.
g Related Links
• "Projector Setup Settings - Extended Menu" p.147
Connecting to a Component-to-VGA Video Source
If your video source has component video ports, you can connect it to the
projector using a component-to-VGA video cable. Depending on your
component ports, you may need to use an adapter cable along with a
component video cable.
You can play sound through the projector's speaker system by connecting a
commercially available stereo mini-jack audio cable or RCA audio cable.
c Tighten the screws on the VGA connector.
d Connect the audio cable to your video source's audio-out ports.
Projector Connections
28
e Connect the other end to the projector's Audio port.
b Connect the other end to the projector's Video port.
If your image colors appear incorrectly, you may need to change the Input
Signal setting in the projector's Signal menu.
c Connect the audio cable to your video source's audio-out ports.
d Connect the other end to the projector's L-Audio-R ports.
s Signal > Advanced > Input Signal
g Related Links
• "Input Signal Settings - Signal Menu" p.143
• "Projector Setup Settings - Extended Menu" p.147
Connecting to a Composite Video Source
If your video source has a composite video port, you can connect it to the
projector using a RCA-style video or A/V cable.
You can play sound through the projector's speaker system by connecting a
commercially available RCA audio cable.
a
Make sure the audio cable is labeled "No resistance".
the cable with the yellow connector to your video source's
a Connect
yellow video output port.
Connecting to External USB Devices
Follow the instructions in these sections to connect external USB devices to
the projector.
g Related Links
• "USB Device Projection" p.29
• "Connecting to a USB Device" p.29
• "Disconnecting a USB Device" p.29
Projector Connections
USB Device Projection
You can project images and other content without using a computer or video
device by connecting any of these devices to your projector:
•
•
•
•
29
the USB cable or USB flash drive to the projector's USB-A port
b Connect
as shown.
USB flash drive
Digital camera or smartphone
USB hard drive
Multimedia storage viewer
a
• Digital cameras or smartphones must be USB-mounted devices, not
TWAIN-compliant devices, and must be USB Mass Storage Classcompliant.
• USB hard drives must meet these requirements:
• USB Mass Storage Class-compliant (not all USB Mass Storage
Class devices are supported)
• Formatted in FAT or FAT32
• Self-powered by their own AC power supplies (bus-powered hard
drives are not recommended)
• Avoid using hard drives with multiple partitions
You can project slide shows from image files on a connected USB device.
g Related Links
• "Projecting a PC Free Presentation" p.71
Connecting to a USB Device
You can connect your USB device to the projector's USB-A port and use it to
project images and other content.
your USB device came with a power adapter, plug the device into an
a Ifelectrical
outlet.
Attention
• Use the USB cable supplied with or specified for use with the device.
• Do not connect a USB hub or a USB cable longer than 3 meters, or the
device may not operate correctly.
c Connect the other end to your device, if necessary.
Disconnecting a USB Device
When you have finished presenting with a connected USB device, disconnect
the device from the projector.
a Turn off and unplug the device, if necessary.
b Disconnect the USB device from the projector.
Connecting to a Document Camera
You can connect a document camera to your projector to project images
viewed by the camera.
Projector Connections
The connection method varies depending on your Epson document camera
model. See the document camera manual for details.
30
c Connect the other end to the projector's HDBaseT port.
Connecting to an HDBaseT Transmitter
To send an HDMI or RS-232C signal over a long distance, you can connect
the projector to an optional HDBaseT transmitter using a 100Base-TX
network cable (EB-2265U/EB-2165W). This is useful when you want to send a
signal to or control the projector from a remote location, such as in a hall or
event site, since you can use a network cable up to 100 m in length. To ensure
proper data transmission, use a Category 5e STP cable or better. However,
operation is not guaranteed for all input/output devices and environments.
a
• To enable communication from the Ethernet and serial ports on the
transmitter, select On as the Control Communications setting in the
projector's Extended menu (Standby Mode in the projector's ECO
menu is automatically set to Communication On). Turning on this
setting disables the projector's LAN and RS-232C ports.
s Extended > HDBaseT > Control Communications
• If you connected an Extron XTP transmitter or switcher to the
projector's HDBaseT port, select On as the Extron XTP setting in the
projector's Extended menu (Control Communications is
automatically set to On, and Standby Mode in the projector's ECO
menu is automatically set to Communication On).
s Extended > HDBaseT > Extron XTP
• Wired remote control using the HDBaseT port is not available.
a Turn off the projector and HDBaseT transmitter.
a
b
Make sure the projector and HDBaseT transmitter are turned off
when connecting or disconnecting a network cable between the
two devices.
Connect one end of the network cable to the HDBaseT port on the
transmitter.
See the documentation that came with the HDBaseT transmitter for
instructions on connecting it to your video device or computer.
d Turn on the projector and HDBaseT transmitter.
g Related Links
• "Projector Setup Settings - Extended Menu" p.147
Connecting to External Output Devices
Follow the instructions in these sections to connect external devices to the
projector.
g Related Links
• "Connecting to a VGA Monitor" p.30
• "Connecting to External Speakers" p.31
Connecting to a VGA Monitor
If you connected the projector to a computer using a Computer port, you can
also connect an external monitor to the projector. This lets you see your
presentation on the external monitor even when the projected image is not
visible.
Projector Connections
a
• If you want to output images to an external monitor when the
projector is turned off, select Always On as the A/V Output setting
in the projector's Extended menu.
s Extended > A/V Settings > A/V Output
• To output images to an external monitor, set Monitor Out Port to
Monitor Out in the projector's Extended menu.
s Extended > Operation > Monitor Out Port
• Monitors that use a refresh rate of less than 60 Hz may not be able to
display images correctly.
sure your computer is connected to the projector's Computer
a Make
port.
a
• If there are two computer ports, make sure you use the
Computer1 port.
• Only analog RGB signals from the Computer1 port can be
output to an external monitor. You cannot output signals
input from other ports or component video signals.
the external monitor's cable to your projector's Monitor Out
b Connect
port.
g Related Links
• "Projector Setup Settings - ECO Menu" p.159
• "Projector Setup Settings - Extended Menu" p.147
31
Connecting to External Speakers
To enhance the sound from your presentation, you can connect the projector
to external self-powered speakers. You can control the volume using the
projector's remote control.
a
• If you want to output audio from the external speakers when the
projector is turned off, select Always On as the A/V Output setting
in the projector's Extended menu.
s Extended > A/V Settings > A/V Output
• You can also connect the projector to an amplifier with speakers.
• The projector's built-in speaker system is disabled when you connect
external speakers.
sure your computer or video source is connected to the projector
a Make
with both audio and video cables as necessary.
the appropriate cable to connect your external speakers, such as
b Locate
a stereo mini-jack-to-pin-jack cable, or another type of cable or adapter.
c Connect one end of the cable to your external speakers as necessary.
the stereo mini-jack end of the cable to your projector's Audio
d Connect
Out port.
Projector Connections
g Related Links
• "Projector Setup Settings - ECO Menu" p.159
• "Projector Setup Settings - Extended Menu" p.147
32
Installing Batteries in the Remote Control
The remote control uses the two AA batteries that came with the projector.
Attention
Make sure you read the Safety Instructions before handling the batteries.
a Remove the battery cover as shown.
b Insert the batteries with the + and – ends facing as shown.
33
Warning
Check the positions of the (+) and (–) marks inside the battery holder to
ensure the batteries are inserted the correct way. If the batteries are not used
correctly, they could explode or leak causing a fire, injury, or damage to the
product.
c Replace the battery cover and press it down until it clicks into place.
g Related Links
• "Remote Control Operation" p.33
Remote Control Operation
The remote control lets you control the projector from almost anywhere in
the room.
Installing Batteries in the Remote Control
Make sure that you aim the remote control at the projector's receivers within
the distance and angles listed here.
a
Avoid using the remote control in conditions with bright fluorescent
lights or in direct sunlight, or the projector may not respond to
commands. If you are not going to use the remote control for a long
time, remove the batteries.
34
Opening the Lens Cover
open the projector's lens cover, slide the A/V Mute slide lever until
a Toit clicks.
cover the lens or temporarily turn off the projected image and
b Tosound,
close the lens cover.
35
Using Basic Projector Features
Follow the instructions in these sections to use your projector's basic features.
g Related Links
• "Turning On the Projector" p.37
• "Turning Off the Projector" p.40
• "Setting the Date and Time" p.41
• "Selecting the Language for the Projector Menus" p.43
• "Projection Modes" p.44
• "Adjusting the Image Height" p.46
• "Image Shape" p.47
• "Resizing the Image with the Zoom Ring" p.54
• "Focusing the Image Using the Focus Ring" p.55
• "Selecting an Image Source" p.56
• "Image Aspect Ratio" p.58
• "Color Mode" p.60
• "Adjusting the Image Color" p.62
• "Controlling the Volume with the Volume Buttons" p.66
Turning On the Projector
Turn on the computer or video equipment you want to use after you turn on
the projector.
37
c Open the projector's lens cover.
the power cord to the projector's power inlet and plug it into
a Connect
an electrical outlet.
Try the following if you do not see a projected image.
The projector's power indicator turns blue. This indicates that the
projector is receiving power, but is not yet turned on (it is in standby
mode).
the power button on the control panel or remote control to turn
b Press
on the projector.
The projector beeps and the status indicator flashes blue as the
projector warms up. Once the projector is warmed up, the status
indicator stops flashing and turns blue.
• Verify the lens cover is open all the way.
• Turn on the connected computer or video device.
• Change the screen output from the computer when using a laptop
computer.
• Insert a DVD or other video media, and press play (if necessary).
• Press the [Source Search] button on the control panel or remote control to
detect the source.
• Press the button for the desired video source on the remote control.
• If the Home screen is displayed, select the source you want to project.
Turning On the Projector
Warning
• Never look into the projector lens when the lamp is on. This can damage your
eyes and is especially dangerous for children.
• When turning on the projector at a distance using the remote control, make sure
there is no one looking into the lens.
• During projection, do not block the light from the projector with a book or other
objects. If the light from the projector is blocked, the area on which the light
shines becomes hot which could cause it to melt, burn, or start a fire. Also, the
lens may get hot due to the reflected light which could cause the projector to
malfunction. To stop projection, use the A/V Mute function, or turn off the
projector.
• A mercury lamp with high internal pressure is used as the projector's light
source. If the lamp is subjected to vibrations or shocks, or if it is used for an
overly extended length of time, the lamp may break or it may not turn on. If the
lamp explodes, gases may escape and small fragments of glass may be scattered
which could cause an injury. Be sure to observe the instructions below.
• Do not disassemble or damage the lamp or subject it to any impacts.
• Do not bring your face close to the projector while it is in use.
• Particular care should be taken when the projector is installed to a ceiling, as
small pieces of glass may fall down when the lamp cover is removed. When
cleaning the projector or replacing the lamp yourself, be very careful not to
allow such pieces of glass to get into the eyes or mouth.
If the lamp breaks, ventilate the area immediately, and contact a doctor if any
fragments of broken glass are inhaled or get into the eyes or mouth.
a
• When the Direct Power On setting is set to On in the projector's
Extended menu, the projector turns on as soon as you plug it in.
Note that the projector also turns on automatically in cases such as
recovery from a power outage.
s Extended > Operation > Direct Power On
• If you select a specific port as the Auto Power On setting in the
projector's Extended menu, the projector turns on as soon as it
detects a signal or cable connection from that port.
(Set Standby Mode to Communication On in the projector's ECO
menu first.)
s Extended > Operation > Auto Power On
38
g Related Links
• "Home Screen" p.38
• "Projector Setup Settings - Extended Menu" p.147
• "Projector Setup Settings - ECO Menu" p.159
Home Screen
The Home screen feature allows you to easily select an image source and
access useful functions. You can display the Home screen by pressing the
[Home] button on the control panel or remote control. The Home screen is
also displayed when you turn on the projector and no signal is being input
from the selected input source.
Press the arrow buttons on the control panel or remote control to select a
menu item, and then press [Enter].
A Selects the source you want to project.
B Displays the QR code that can be recognized by Epson iProjection to project
data on a smartphone or tablet device.
C Displays the Help screen.
Turning On the Projector
D Displays the projector's menu.
E Performs menu options assigned to Home Screen in the projector's Extended
menu.
F Projects two images from different image sources simultaneously by splitting
the projected screen.
G Corrects the shape of an image that is an uneven rectangle.
a
The Home screen disappears after 10 minutes of inactivity.
g Related Links
• "Image Shape" p.47
• "Projector Setup Settings - Extended Menu" p.147
• "Using a QR Code to Connect a Mobile Device" p.110
• "Using the Projector's Menus" p.139
• "Using the Projector Help Displays" p.185
• "Projecting Two Images Simultaneously" p.68
39
Turning Off the Projector
Turn off the projector after use.
a
• Turn off this product when it is not in use to prolong the life of the
projector. Lamp life varies depending on the mode selected,
environmental conditions, and usage. Brightness decreases over time.
• Since the projector supports the direct shutdown feature, it can be
turned off directly using the breaker.
40
or store the projector, make sure the power indicator is
c Tobluetransport
(but not flashing) and the status indicator is off, then unplug the
power cord.
the power button on the control panel or remote control.
a Press
The projector displays a shutdown confirmation screen.
the power button again. (To leave it on, press any other button.)
b Press
The projector beeps twice, the lamp turns off, and the status indicator
turns off.
a
With Epson's Instant Off technology, there is no cool-down
period so you can pack up the projector for transport right away.
d Close the projector's lens cover.
Setting the Date and Time
You can set the date and time for the projector (EB-2265U/EB-2255U/EB2250U/EB-2245U/EB-2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EBX500KG).
41
You see this screen:
a Turn on the projector.
b Press the [Menu] button on the control panel or remote control.
c Select the Extended menu and press [Enter].
d Select the Operation setting and press [Enter].
the Date & Time setting and press [Enter].
e Select
You see this screen:
f Select the Date & Time setting and press [Enter].
Date, press [Enter], and use the displayed keyboard to enter
g Select
today's date.
Time, press [Enter], and use the displayed keyboard to enter the
h Select
current time.
Time Difference (UTC), press [Enter], and set the time
i Select
difference from Coordinated Universal Time.
j When you are finished, select Set and press [Enter].
Setting the Date and Time
activate daylight saving time, select the Daylight Saving Time
k Tosetting
and press [Enter]. Then select settings.
l When you are finished, select Set and press [Enter].
the time automatically through an Internet time server,
m Toselectupdate
the Internet Time setting and press [Enter]. Then select settings.
n When you are finished, select Set and press [Enter].
o Press [Menu] or [Esc] to exit the menus.
42
Selecting the Language for the Projector Menus
If you want to view the projector's menus and messages in another language,
you can change the Language setting.
a Turn on the projector.
b Press the [Menu] button on the control panel or remote control.
c Select the Extended menu and press [Enter].
d Select the Language setting and press [Enter].
e Select the language you want to use and press [Enter].
f Press [Menu] or [Esc] to exit the menus.
43
Projection Modes
Depending on how you positioned the projector, you may need to change the
projection mode so your images project correctly.
• Front (default setting) lets you project from a table in front of the screen.
• Front/Ceiling flips the image over top-to-bottom to project upside-down
from a ceiling or wall mount.
• Rear flips the image horizontally to project from behind a translucent
screen.
• Rear/Ceiling flips the image over top-to-bottom and horizontally to project
from a ceiling or wall mount and behind a translucent screen.
g Related Links
• "Changing the Projection Mode Using the Remote Control" p.44
• "Changing the Projection Mode Using the Menus" p.44
• "Projector Setup and Installation Options" p.22
44
projection back to the original mode, hold down the [A/V
c ToMute]change
button for 5 seconds again.
Changing the Projection Mode Using the Menus
You can change the projection mode to flip the image over top-to-bottom
and/or left-to-right using the projector menus.
a Turn on the projector and display an image.
b Press the [Menu] button on the control panel or remote control.
Changing the Projection Mode Using the Remote
Control
You can change the projection mode to flip the image over top-to-bottom.
a Turn on the projector and display an image.
b Hold down the [A/V Mute] button on the remote control for 5 seconds.
The image disappears briefly and reappears flipped top-to-bottom.
c Select the Extended menu and press [Enter].
Projection Modes
d Select Projection and press [Enter].
e Select a projection mode and press [Enter].
f Press [Menu] or [Esc] to exit the menus.
45
Adjusting the Image Height
If you are projecting from a table or other flat surface and the image is too
high or low, you can adjust the image height using the projector's adjustable
feet.
46
d If the image is tilted, rotate the rear feet to adjust their height.
The larger the angle of tilt, the harder it becomes to focus. Locate the
projector so that it only needs to be tilted at a small angle.
a Turn on the projector and display an image.
the front foot, pull up on the foot release lever and lift the
b Tofrontadjust
of the projector.
A Extend the rear foot
B Retract the rear foot
If the projected image is unevenly rectangular, you need to adjust the image
shape.
The foot extends from the projector.
You can adjust the position up to 14 degrees.
c Release the lever to lock the foot.
g Related Links
• "Image Shape" p.47
Image Shape
You can project an even, rectangular image by placing the projector directly
in front of the center of the screen and keeping it level. If you place the
projector at an angle to the screen, or tilt it up or down, or off to the side, you
may need to correct the image shape.
g Related Links
• "Auto H/V-Keystone" p.47
• "Auto V-Keystone" p.47
• "Automatically Correcting the Image Shape with Screen Fit" p.47
• "Correcting the Image Shape with the Horizontal Keystone Slider" p.49
• "Correcting the Image Shape with the Keystone Buttons" p.50
• "Correcting the Image Shape with Quick Corner" p.51
Auto H/V-Keystone
When the projector is moved or tilted, Auto H/V-Keystone automatically
corrects any vertical and horizontal keystone distortion (EB-2265U/EB2255U/EB-2250U/EB-2245U/EB-2165W/EB-2155W/EB-2065/EB-2055/EBX550KG/EB-X500KG).
When the projector is moved, it displays an adjustment screen and then
automatically corrects the projected image.
Auto H/V-Keystone can correct the projected image distortion in these
conditions:
• Screen size is 100 inches or less (EB-2265U/EB-2255U/EB-2250U/EB2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG)
• Screen size is 88 inches or less (EB-2245U)
• Projection distance is about 1.5 to 3.0 m (EB-2265U/EB-2255U/EB2250U/EB-2245U)
• Projection distance is about 0.9 to 3.0 m (EB-2165W/EB-2155W/EB2065/EB-2055/EB-X550KG/EB-X500KG)
• Projection angle is about 20º right or left, or 30º up or down
• The Projection setting is set to Front in the projector's Extended menu
47
a
If you do not want to use the Auto H/V-Keystone function, set Auto
H/V-Keystone to Off in the projector's Settings menu.
s Settings > Keystone > H/V-Keystone > Auto H/V-Keystone
g Related Links
• "Projection Modes" p.44
• "Projector Setup Settings - Extended Menu" p.147
• "Projector Feature Settings - Settings Menu" p.145
Auto V-Keystone
When the projector is moved or tilted, Auto V-Keystone automatically
corrects any vertical keystone distortion (EB-2140W/EB-2040).
Auto V-Keystone can correct the projected image distortion in these
conditions:
• Projection angle is about 30º up or down
• The Projection setting is set to Front in the projector's Extended menu
a
If you do not want to use the Auto V-Keystone function, set Auto VKeystone to Off in the projector's Settings menu.
s Settings > Keystone > H/V-Keystone > Auto V-Keystone
g Related Links
• "Projection Modes" p.44
• "Projector Setup Settings - Extended Menu" p.147
• "Projector Feature Settings - Settings Menu" p.145
Automatically Correcting the Image Shape with
Screen Fit
You can use the projector's Screen Fit feature to automatically correct the
shape and position of images to fit on your screen (EB-2265U/EB-2255U/EB-
Image Shape
2250U/EB-2245U/EB-2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EBX500KG).
48
b Press the [Screen Fit] button on the control panel or remote control.
You see a message on the screen.
The projector's sensor can detect the screen size and shape in these
conditions:
• Screen size is 100 inches or less (EB-2265U/EB-2255U/EB-2250U/EB2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG)
• Screen size is 88 inches or less (EB-2245U)
• Projection distance is about 1.5 to 3.0 m (EB-2265U/EB-2255U/EB2250U/EB-2245U)
• Projection distance is about 1.2 to 3.0 m (EB-2165W/EB-2155W/EB2065/EB-2055/EB-X550KG/EB-X500KG)
• Projection angle is about 20º right or left, or 30º up or down
• The room is not too dark
• The projection surface is not patterned and does not deflect the sensor in
some way
a Turn on the projector and display an image.
the projector as necessary to display the message in the middle of
c Move
the screen.
into the image until the yellow frame extends beyond the edges
d Zoom
of the screen.
Image Shape
a
• If the yellow frame is still within the screen frame after
zooming in all the way, move the projector farther away from
the screen.
• For example, when you project onto a wide screen in a small
room and you cannot extend the yellow frame beyond the
screen frame, the yellow frame must include at least the top
and bottom two sides of the screen so that Screen Fit detects
the screen height and adjusts the image to fit the screen.
49
• "Correcting the Image Shape with Quick Corner" p.51
Correcting the Image Shape with the Horizontal
Keystone Slider
You can use the projector's horizontal keystone slider to correct the shape of
an image that is an uneven horizontal rectangle, such as when the projector is
placed to the side of the projection area (EB-2140W/EB-2040).
You can make effective corrections when the projection angle is about 30º
right or left.
the [Screen Fit] button again.
e Press
After the adjustment screen appears, do not move the projector or
block the image. The projected image is corrected according to the
aspect ratio of the image being input and this message appears.
the image shape as necessary using the keystone adjustment
f Fine-tune
buttons on the control panel.
If no operations are performed, the message closes after about 7
seconds.
g When you are finished, press [Esc].
The Keystone setting is now set to Quick Corner in the projector's Settings
menu. If necessary, you can correct the image corners individually using
Quick Corner by pressing the arrow buttons on the control panel.
g Related Links
• "Projector Feature Settings - Settings Menu" p.145
a Turn on the projector and display an image.
b Adjust the slider until the image is an even rectangle.
After correction, your image is slightly smaller.
a
• When you use the horizontal keystone slider, set H-Keystone
Adjuster to On in the projector's Settings menu.
s Settings > Keystone > H/V-Keystone > H-Keystone
Adjuster
• You can also correct the shape of the image in the horizontal
direction in the projector's Settings menu.
s Settings > Keystone > H/V-Keystone
g Related Links
• "Projector Feature Settings - Settings Menu" p.145
Image Shape
Correcting the Image Shape with the Keystone
Buttons
50
c Press a keystone button to adjust the image shape.
You can use the projector's keystone correction buttons to correct the shape
of an image that is unevenly rectangular.
You can use keystone buttons to correct images up to 30º right, left, up, or
down.
a Turn on the projector and display an image.
one of the keystone adjustment buttons on the control panel to
b Press
display the Keystone adjustment screen.
After correction, your image is slightly smaller.
a
If the projector is installed out of your reach, you can also correct
the shape of the image using the remote control.
s Settings > Keystone > H/V-Keystone
g Related Links
• "Projector Feature Settings - Settings Menu" p.145
Image Shape
Correcting the Image Shape with Quick Corner
51
c Select the Settings menu and press [Enter].
You can use the projector's Quick Corner setting to correct the shape and size
of an image that is unevenly rectangular.
a Turn on the projector and display an image.
b Press the [Menu] button on the control panel or remote control.
d Select Keystone and press [Enter].
Image Shape
e Select Quick Corner and press [Enter]. Press [Enter] again if necessary.
52
a
• If you see this screen, you cannot adjust the shape any further
in the direction indicated by the gray triangle.
You see the area selection screen.
the arrow buttons to select the corner of the image you want to
f Use
adjust. Then press [Enter].
• To reset the Quick Corner corrections, hold down [Esc] for
about 2 seconds while the Quick Corner adjustment screen is
displayed, and select Reset Quick Corner. Select Switch to
H/V-Keystone to switch the image shape correction method to
H/V-Keystone.
the arrow buttons to adjust the image shape as necessary.
g Press
To return to the area selection screen, press [Enter].
h Repeat steps 6 and 7 as needed to adjust any remaining corners.
i When you are finished, press [Esc].
The Keystone setting is now set to Quick Corner in the projector's Settings
menu. The next time you press the keystone adjustment buttons on the
control panel, the area selection screen is displayed.
Image Shape
g Related Links
• "Projector Feature Settings - Settings Menu" p.145
53
Resizing the Image with the Zoom Ring
You can resize the image using the projector's zoom ring.
a Turn on the projector and display an image.
b Rotate the zoom ring to enlarge or reduce the image.
54
Focusing the Image Using the Focus Ring
You can correct the focus using the focus ring.
55
the [Focus Help] button on the control panel to display the Focus
b Press
Help screen.
You can also use the projector's Focus Help screen to fine-tune your focus
adjustments (EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB-2165W/EB2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG).
The Focus Help screen lets you correct the projected image under the
following conditions:
•
•
•
•
•
Screen size is 100 inches or less
Projection distance is about 1.5 to 3.0 m (EB-2265U/EB-2255U/EB-2250U)
Projection distance is about 1.5 to 3.4 m (EB-2245U)
Projection distance is about 0.9 to 3.0 m (EB-2165W/EB-2155W)
Projection distance is about 0.9 to 2.8 m (EB-2065/EB-2055/EBX550KG/EB-X500KG)
• Projection angle is about 20º right or left, or 30º up or down
• The projection environment is not too bright
the focus ring until the two orange circles overlap in the center
c Rotate
of the Focus Help screen.
a Turn on the projector and display an image.
d Press [Focus Help] or [Esc] to exit the screen.
Selecting an Image Source
When multiple image sources are connected to the projector, such as a
computer and DVD player, you can switch from one image source to the
other.
56
a
This screen is displayed when no image signal is detected.
Check the cable connections between the projector and image
source.
a Make sure the connected image source you want to use is turned on.
video image sources, insert a DVD or other video media and press
b For
play.
one of the following:
c Do
• Press the [Source Search] button on the control panel or remote
control until you see the image from the source you want.
• Press the button for the source you want on the remote control. If
there is more than one port for that source, press the button again to
cycle through the sources.
A Computer port source (Computer1 and Computer2 ports)
B Video, HDMI, MHL and HDBaseT sources (Video, HDMI1/MHL,
HDMI2 and HDBaseT ports)
Selecting an Image Source
C USB port sources (USB-B port and external devices connected to the
USB-A ports)
D Network source (LAN and Screen Mirroring)
• Press the [Home] button on the control panel or remote control.
Then select the source you want to use from the screen displayed.
a
• HDBaseT is available only with the EB-2265U/EB-2165W.
• Screen Mirroring is available only with the EB-2265U/EB2255U/EB-2165W.
57
Image Aspect Ratio
The projector can display images in different width-to-height ratios called
aspect ratios. Normally, the input signal from your video source determines
the image's aspect ratio. However, for certain images you can change the
aspect ratio to fit your screen.
If you always want to use a particular aspect ratio for a certain video input
source, you can select it using the projector's Signal menu.
g Related Links
• "Changing the Image Aspect Ratio" p.58
• "Available Image Aspect Ratios" p.58
• "Projected Image Appearance with Each Aspect Mode" p.59
• "Input Signal Settings - Signal Menu" p.143
Changing the Image Aspect Ratio
You can change the aspect ratio of the displayed image.
58
a
To display images without black bars, set Resolution to Wide or
Normal in the projector’s Signal menu according to the computer’s
resolution.
g Related Links
• "Input Signal Settings - Signal Menu" p.143
Available Image Aspect Ratios
You can select the following image aspect ratios, depending on the input
signal from your image source.
a
a Turn on the projector and switch to the image source you want to use.
b Press the [Aspect] button on the remote control.
• Black bands and cropped images may project in certain aspect ratios,
depending on the aspect ratio and resolution of your input signal.
• The Auto aspect ratio setting is available only for HDMI image
sources.
• Note that using the aspect ratio function of the projector to reduce,
enlarge, or split the projected image for commercial purposes or for
public viewing may infringe upon the rights of the copyright holder
of that image based on copyright law.
For projectors with a resolution of WUXGA (1920 × 1200) or WXGA
(1280 × 800)
through the available aspect ratios for your input signal, press
c Tothe cycle
[Aspect] button repeatedly.
Aspect mode
Description
Auto
Automatically sets the aspect ratio according to the
input signal and the Resolution setting.
Normal
Displays images using the full projection area and
maintains the aspect ratio of the image.
16:9
Converts the aspect ratio of the image to 16:9.
Full
Displays images using the full size of the projection
area, but does not maintain the aspect ratio.
Zoom
Displays images using the full width of the projection
area and maintains the aspect ratio of the image.
Image Aspect Ratio
59
Aspect mode
Description
Aspect mode
Native
Displays images as is (aspect ratio and resolution are
maintained).
Aspect ratio for input signals
16:10
16:9
4:3
16:9
For projectors with a resolution of XGA (1024 × 768)
Full
Aspect mode
Description
Auto
Automatically sets the aspect ratio according to the
input signal and the Resolution setting.
Normal
Displays images using the full projection area and
maintains the aspect ratio of the image.
4:3
Converts the aspect ratio of the image to 4:3.
16:9
Converts the aspect ratio of the image to 16:9.
Projected Image Appearance with Each Aspect Mode
Black bands and cropped images may project in certain aspect ratios,
depending on the aspect ratio and resolution of your input signal. See the
following table to confirm the position of black bands and cropped images.
a
The image for Native varies depending on the input signal.
Zoom
Native
For projectors with a resolution of XGA (1024 × 768)
Aspect mode
16:10
Normal
Auto
4:3
For projectors with a resolution of WUXGA (1920 × 1200) or WXGA
(1280 × 800)
Aspect mode
16:10
Normal
Auto
16:9
Aspect ratio for input signals
16:9
4:3
Aspect ratio for input signals
16:9
4:3
Color Mode
The projector offers different color modes to provide optimum brightness,
contrast, and color for a variety of viewing environments and image types.
You can select the mode designed to match your image and environment, or
experiment with the available modes.
g Related Links
• "Changing the Color Mode" p.60
• "Available Color Modes" p.60
• "Setting Auto Iris" p.60
Changing the Color Mode
You can change the projector's Color Mode using the remote control to
optimize the image for your viewing environment.
a Turn on the projector and switch to the image source you want to use.
the [Color Mode] button on the remote control to change the
b Press
Color Mode.
The name of the Color Mode appears briefly on the screen and then
image appearance changes.
all of the available color modes for your input signal,
c Topresscyclethethrough
[Color Mode] button repeatedly.
60
a
You can also set the Color Mode setting in the projector's Image
menu.
g Related Links
• "Image Quality Settings - Image Menu" p.141
Available Color Modes
You can set the projector to use these color modes, depending on the input
source you are using:
Color mode
Description
Presentation
Best for projecting vivid images.
Dynamic
This is the brightest mode. Best for prioritizing
brightness.
Cinema
Best for enjoying content such as movies.
sRGB
Best for faithfully reproducing the color of the source
image.
Blackboard
Best for projecting images directly on a green
chalkboard.
DICOM SIM
Best for projecting X-ray photographs and other
medical images. This mode is for reference purposes
only and should not be used to make medical
diagnoses.
Setting Auto Iris
You can turn on Auto Iris to automatically optimize the image based on the
brightness of the content.
This setting is available for Dynamic or Cinema color modes.
a Turn on the projector and switch to the image source you want to use.
Color Mode
b Press the [Menu] button on the control panel or remote control.
61
d Select Auto Iris and press [Enter].
c Select the Image menu and press [Enter].
one of the following options and press [Enter]:
e Choose
• High Speed to adjust brightness as soon as the scene changes.
• Normal for standard brightness adjustment.
f Press [Menu] or [Esc] to exit the menus.
Adjusting the Image Color
You can fine-tune various aspects of how colors are displayed in your
projected images.
62
c Select the Image menu and press [Enter].
g Related Links
• "Adjusting the Hue, Saturation, and Brightness" p.62
• "Adjusting the Gamma" p.63
Adjusting the Hue, Saturation, and Brightness
You can adjust the Hue, Saturation, and Brightness settings for individual
image colors.
a Turn on the projector and switch to the image source you want to use.
b Press the [Menu] button on the control panel or remote control.
d Select Advanced and press [Enter].
e Select RGBCMY and press [Enter].
the following as necessary for each R (red), G (green), B (blue), C
f Do
(cyan), M (magenta) and Y (yellow):
• To adjust the overall hue of the color, bluish - greenish - reddish,
adjust the Hue setting.
• To adjust the overall vividness of the color, adjust the Saturation
setting.
Adjusting the Image Color
• To adjust the overall color brightness of the color, adjust the
Brightness setting.
63
c Select the Image menu and press [Enter].
g Press [Menu] or [Esc] to exit the menus.
Adjusting the Gamma
You can correct differences in projected image colors that occur between
different image sources by adjusting the Gamma setting.
a Turn on the projector and switch to the image source you want to use.
b Press the [Menu] button on the control panel or remote control.
d Select Advanced and press [Enter].
e Select Gamma and press [Enter].
f Select and adjust the correction value.
When you select a smaller value, you can reduce the overall brightness
of the image to make the image sharper. When you select a larger value,
Adjusting the Image Color
the dark areas of images become brighter, but the color saturation for
lighter areas may become weaker.
a
64
[Enter]. Then press the up or down arrow button to adjust the value
for the selected color tone and press [Enter].
• If you selected DICOM SIM as the Color Mode setting in the
projector's Image menu, select the adjustment value according
to the projection size.
• If the projection size is 80 inches or less, select a small value.
• If the projection size is 80 inches or more, select a large
value.
• Medical images may not be reproduced correctly depending on
your settings and screen specifications.
you want to make finer adjustments, select Customized and press
g If[Enter].
the value using one of the following methods.
h Adjust
• To select the color tone you want to adjust from the image, select
Adjust it from the image. Press the arrow buttons to move the
cursor to the part where you want to change the brightness and press
• To use the gamma adjustment graph, select Adjust it from the
graph. Press the left or right arrow buttons to select the color tone
Adjusting the Image Color
you want to adjust. Then press the up or down arrow button to
adjust the value and press [Enter].
i Press [Menu] or [Esc] to exit the menus.
g Related Links
• "Image Quality Settings - Image Menu" p.141
65
Controlling the Volume with the Volume Buttons
The volume buttons control the projector's internal speaker system.
You can also control the volume of any external speakers you connected to
the projector.
You must adjust the volume separately for each connected input source.
a Turn on the projector and start a presentation.
lower or raise the volume, press the [Volume] buttons on the
b Tocontrol
panel or remote control as shown.
A volume gauge appears on the screen.
the volume to a specific level for an input source, select Volume
c Toin theset projector's
Settings menu.
Caution
Do not start a presentation at a high volume setting. Sudden loud noises may cause
hearing loss.
Always lower the volume before powering off, so that you can power on and then
gradually increase the volume.
g Related Links
• "Projector Feature Settings - Settings Menu" p.145
66
Adjusting Projector Features
Follow the instructions in these sections to use your projector's adjustment features.
g Related Links
• "Projecting Two Images Simultaneously" p.68
• "Projecting a PC Free Presentation" p.71
• "Controlling a Presentation with Your Hands" p.78
• "Shutting Off the Image and Sound Temporarily" p.81
• "Stopping Video Action Temporarily" p.82
• "Zooming Images" p.83
• "Using the Remote Control as a Wireless Mouse" p.84
• "Using the Remote Control as a Pointer" p.86
• "Saving a User's Logo Image" p.87
• "Using Multiple Projectors" p.89
• "Projector Security Features" p.94
Projecting Two Images Simultaneously
You can use the split screen feature to simultaneously project two images
from different image sources. You can control the split screen feature using
the remote control or the projector menus.
68
a Press the [Split] button on the remote control.
The currently selected input source moves to the left of the screen.
a
You can perform the same operations from Split Screen in the
projector's Settings menu.
the [Menu] button.
b Press
You see this screen:
a
• While using the split screen feature, other projector features may not
be available and some settings may be automatically applied to both
images.
Projecting Two Images Simultaneously
an input source for the other image, select the Source setting,
c Topressselect
[Enter], select the input source, select Execute, and press [Enter].
69
one image while reducing the other image, select Screen
e ToSize,enlarge
press [Enter], select a size, and press [Enter]. To exit the menu,
press [Menu].
a
Depending on the video input signals, the images may not
appear at the same size even if you select Equal.
select the audio, select Audio Source, press [Enter], select an audio
f Tooption,
and press [Enter]. To exit the menu, press [Menu].
a
• You can only select input sources that can be combined.
• While using the split screen feature, the Source screen appears
when you change the input source from the remote control.
images, select Swap Screens and press [Enter].
d ToTheswitch
projected images on the left and right are swapped.
a
Select Auto to hear audio from the largest screen or the left
screen.
the projected images to the top of the screen, select Align,
g Topressalign[Enter],
select Top, and press [Enter] again. To exit the menu,
press [Menu].
h To exit the split screen feature, press [Split] or [Esc].
g Related Links
• "Unsupported Input Source Combinations for Split Screen Projection" p.70
• "Split Screen Projection Restrictions" p.70
Projecting Two Images Simultaneously
Unsupported Input Source Combinations for Split
Screen Projection
These input source combinations cannot be projected on a split screen.
•
•
•
•
•
Computer1 and Computer2
Computer1/Computer2 and Video
USB Display and USB/LAN
USB and LAN
LAN (Wireless) and Screen Mirroring
Split Screen Projection Restrictions
Operating restrictions
The following operations cannot be performed during split screen projection.
•
•
•
•
•
Setting the projector's menu
E-Zoom
Switching the aspect mode (the aspect mode is set to Normal)
Operations using the [User] button on the remote control
Auto Iris
Image restrictions
• If you make adjustments such as Brightness, Contrast, Color Saturation,
Tint, and Sharpness in the projector's Image menu, you can apply them
only to the image on the left. Default adjustments are applied to the image
on the right. Adjustments that affect the entire projected image such as
Color Mode and Color Temp. are applied for both left and right images.
• Even if you make adjustments for Noise Reduction and Deinterlacing in
the projector's Image menu, Noise Reduction is set to 0 and Deinterlacing
is set to Off for the image on the right.
s Image > Image Enhancement > Noise Reduction
s Image > Advanced > Deinterlacing
70
• Even if you set Display Background to Logo in the projector's Extended
menu, the blue screen appears when no image signal is being input.
g Related Links
• "Image Aspect Ratio" p.58
• "Color Mode" p.60
• "Projector Feature Settings - Settings Menu" p.145
• "Input Signal Settings - Signal Menu" p.143
• "Projector Setup Settings - Extended Menu" p.147
• "Zooming Images" p.83
• "Setting Auto Iris" p.60
• "Adjusting the Image Color" p.62
Projecting a PC Free Presentation
You can use your projector's PC Free feature whenever you connect a USB
device that contains compatible presentation files. This lets you quickly and
easily display a presentation and control it using the projector's remote
control.
g Related Links
• "Supported PC Free File Types" p.71
• "Precautions on PC Free Projection" p.71
• "Starting a PC Free Slide Show" p.72
• "Starting a PC Free PDF File Presentation" p.73
• "Starting a PC Free Movie Presentation" p.75
• "PC Free Display Options" p.76
Supported PC Free File Types
You can project these types of files using the projector's PC Free feature.
a
• For best results, place your files on media that is formatted in
FAT16/32.
• If you have trouble projecting from media formatted for nonWindows file systems, try formatting the media for Windows
instead.
71
File contents File type
Details
(extension)
Image
.jpg
Make sure the file is not:
• CMYK format
• Progressive format
• Highly compressed
• Above 8192 × 8192 resolution
.bmp
Make sure the file is not:
• Above 1280 × 800 resolution
.gif
Make sure the file is not:
• Above 1280 × 800 resolution
• Animated
• Interlaced
.png
Make sure the file is not:
• Above 1280 × 800 resolution *
• Interlaced
PDF
.pdf
Make sure the file is not:
• Saved in PDF version 1.8 or later format
• Encrypted
Movie
.avi
(Motion
JPEG)
Supports only AVI 1.0.
Make sure the file is not:
• Saved with an audio codec other than PCM or
ADPCM
• Above 1280 × 720 resolution
• Larger than 2 GB
* When you use a projectors with a resolution of WUXGA, make sure the file
is not above 1920 × 1200 resolution.
Precautions on PC Free Projection
Note the following precautions when using PC Free features.
Projecting a PC Free Presentation
• Do not disconnect the USB storage device while it is being accessed;
otherwise, PC Free may not operate correctly.
• You may not be able to use the security features on certain USB storage
devices with PC Free features.
• When connecting a USB device that includes an AC adapter, connect the
AC adapter to an electrical outlet when you use the device with your
projector.
• Some commercially available USB card readers may not be compatible with
the projector.
• The projector can recognize up to 5 cards inserted into the connected card
reader at one time.
• You cannot correct keystone distortion while projecting in PC Free, so
correct the image shape before you begin your presentation.
• You can use the following functions while projecting in PC Free.
•
•
•
•
Freeze
A/V Mute
E-Zoom
Pointer
g Related Links
• "Stopping Video Action Temporarily" p.82
• "Shutting Off the Image and Sound Temporarily" p.81
• "Zooming Images" p.83
• "Using the Remote Control as a Pointer" p.86
72
the [USB] button on the remote control.
a Press
The PC Free file list screen is displayed.
a
• If the Select Drive screen is displayed, press the arrow buttons
to select the drive and press [Enter].
• To display the Select Drive screen, highlight Select Drive at the
top of the file list screen and press [Enter].
one of the following to locate your files:
b Do
• If you need to display files inside a subfolder on your device, press
the arrow buttons to highlight the folder and press [Enter].
Starting a PC Free Slide Show
After connecting a USB device to the projector, you can switch to the USB
input source and start your slide show.
a
• You can change the PC Free operation options or add special effects
by highlighting Option at the bottom of the screen and pressing
[Enter].
• To move back up a folder level on your device, highlight Back to
Top and press [Enter].
• To view additional files in a folder, highlight Next Page or Previous
Page and press [Enter], or press the [Page] up or down buttons on
the remote control.
one of the following:
c Do
• To display an individual image, press the arrow buttons to highlight
the image and press [Enter]. (Press the [Esc] button to return to the
file list screen.)
Projecting a PC Free Presentation
• To display a slide show of all the images in a folder, press the arrow
buttons to highlight the Slideshow option at the bottom of the screen
and press [Enter].
a
• You can change the image switching time by highlighting
Option at the bottom of the screen and pressing [Enter].
• If any file names are longer than the display area or include
unsupported symbols, the file names may be shortened or
changed only on the screen display.
projecting, use the following commands to control the display:
d While
• To rotate a displayed image, press the up or down arrow button.
73
off the USB device, if necessary, and then disconnect the device
f Turn
from the projector.
g Related Links
• "PC Free Display Options" p.76
• "Connecting to a USB Device" p.29
Starting a PC Free PDF File Presentation
After connecting a USB device to the projector, you can switch to the USB
input source and start your PDF file presentation.
a
• You cannot do the following while presenting a PDF file from a USB
device:
• Release a password
• Display e-signatures, JPEG2000 images, transparent effects, 3D
artwork, or comments
• Play multimedia content
• Display encrypted PDF content
• Display a PDF file without a .pdf file extension
a Press the [USB] button on the remote control.
• To move to the next or previous image, press the left or right arrow
button.
stop the display, follow the on-screen instructions or press the [Esc]
e Tobutton.
You return to the file list screen.
Projecting a PC Free Presentation
The PC Free file list screen is displayed.
a
• If the Select Drive screen is displayed, press the arrow buttons
to select the drive and press [Enter].
• To display the Select Drive screen, highlight Select Drive at the
top of the file list screen and press [Enter].
b • If you need to display files inside a subfolder on your device, press
Do one of the following to locate your files:
the arrow buttons to highlight the folder and press [Enter].
• To move back up a folder level on your device, highlight Back to
Top and press [Enter].
• To view additional files in a folder, highlight Next Page or Previous
Page and press [Enter], or press the [Page] up or down buttons on
the remote control.
the arrow buttons to highlight the file and press [Enter]. (Press
c Press
the [Esc] button to return to the file list screen.)
74
The first page in the PDF file is displayed at full screen size.
a
If any file names are longer than the display area or include
unsupported symbols, the file names may be shortened or
changed only on the screen display.
projecting a PDF file, use the following commands to control the
d While
display:
• To move to the next or previous page, press the up or down arrow
button.
• To display a menu of pages to select from, press the [Esc] button,
press the left or right arrow button to select a page and press [Enter].
Projecting a PC Free Presentation
(If you press [Esc] while the select page menu is displayed, the menu
closes.)
75
Starting a PC Free Movie Presentation
After connecting a USB device to the projector, you can switch to the USB
input source and start your movie.
a
• You can change the PC Free operation options by highlighting
Option at the bottom of the screen and pressing [Enter].
the [USB] button on the remote control.
a Press
The PC Free file list screen is displayed.
• To enlarge the view of a page to fit the screen, press [Enter]. Portrait
pages are expanded horizontally to fit the width of the screen, and
landscape pages are expanded vertically to fit the height of the
screen. To scroll the page while a page is displayed at expanded size,
press the arrow buttons. Press [Enter] again to return to standard
size display.
• To rotate a displayed page, press the left or right arrow button.
stop the display, press the [Esc] button, highlight Exit, and press
e To[Enter].
off the USB device, if necessary, and then disconnect the device
f Turn
from the projector.
g Related Links
• "Connecting to a USB Device" p.29
a
• If the Select Drive screen is displayed, press the arrow buttons
to select the drive and press [Enter].
• To display the Select Drive screen, highlight Select Drive at the
top of the file list screen and press [Enter].
one of the following to locate your files:
b Do
• If you need to display files inside a subfolder on your device, press
the arrow buttons to highlight the folder and press [Enter].
Projecting a PC Free Presentation
• To move back up a folder level on your device, highlight Back to
Top and press [Enter].
• To view additional files in a folder, highlight Next Page or Previous
Page, and press [Enter], or press the [Page] up or down buttons on
the remote control.
76
PC Free Display Options
You can select these display options when using PC Free. To access this
screen, highlight Option at the bottom of the PC Free file list screen and press
[Enter].
back a movie, press the arrow buttons to highlight the file and
c Topressplay[Enter].
a
• If any file names are longer than the display area or include
unsupported symbols, the file names may be shortened or
changed only on the screen display.
• If you want to play back all the movies in a folder in sequence,
select the Slideshow option at the bottom of the screen.
movie playback, press the [Esc] button, highlight Exit, and
d Topressstop[Enter].
You return to the file list screen.
off the USB device, if necessary, and then disconnect the device
e Turn
from the projector.
g Related Links
• "PC Free Display Options" p.76
• "Connecting to a USB Device" p.29
Setting
Options
Description
Display Order
Name Order
Displays files in name order
Date Order
Displays files in date order
In Ascending
Sorts files in first-to-last order
In Descending
Sorts files in last-to-first order
On
Displays a slide show continuously
Off
Displays a slide show once
No
Does not display the next file
automatically
1 Second to 60 Seconds
Displays files for the selected time
and switches to the next file
automatically; high resolution images
may switch at a slightly slower rate
Sort Order
Continuous Play
Screen Switching
Time
Projecting a PC Free Presentation
Setting
Options
Description
Effect
No
No effect
Wipe
Transitions between images using a
wipe effect
Dissolve
Transitions between images using a
dissolve effect
Random
Transitions between images using a
random variety of effects
77
Controlling a Presentation with Your Hands
You can use the Gesture Presenter feature to control presentations using your
hands, which allows you to give presentations in front of the screen without
using a presentation remote control (EB-2265U/EB-2255U/EB-2250U/EB2245U/EB-2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG).
The Gesture Presenter feature is available in these conditions:
• The Gesture Presenter setting is set to On in the projector's Settings menu
s Settings > Gesture Presenter > Gesture Presenter
• The Projection setting is set to Front or Front/Ceiling in the projector's
Extended menu
• Screen size is 100 inches or less
• Projection distance is about 1.5 to 3.0 m (EB-2265U/EB-2255U/EB-2250U)
• Projection distance is about 1.5 to 3.4 m (EB-2245U)
• Projection distance is about 1.2 to 3.0 m (EB-2165W/EB-2155W)
• Projection distance is about 1.2 to 2.8 m (EB-2065/EB-2055/EBX550KG/EB-X500KG)
• Projection angle is about 20º right or left, or 20º up or down
• A Screen Mirroring connection is established with the operation
permissions that allow a connected device's keyboard or mouse to control
the projector. (Windows 10 only)
a
Adjust the image settings such as keystone and color mode before
starting the Gesture Presenter feature. When you adjust the image
settings while using the Gesture Presenter feature, the marker may not
be recognized correctly.
a Connect the projector to a computer using a signal cable or a network.
you want to connect your computer without using the projector's
b IfUSB-B
port, make sure you connect a USB cable to the projector's USBB port and to a USB port on your computer (for Gesture Presenter
support).
78
a
When connecting your computer using EasyMP Multi PC
Projection or the Screen Mirroring connection in Windows 10,
you do not need to connect a USB cable.
c Turn on the projector and start your presentation.
d Press the [Gesture] button on the remote control.
The menu for the Gesture Presenter feature is displayed.
Controlling a Presentation with Your Hands
You can also display the menu for the Gesture Presenter feature
by holding down the [Screen Fit] button on the control panel for
three seconds, or by selecting Gesture Presenter in the
projector's Settings menu.
a
79
a
Start/Stop.
e Select
An adjustment screen is displayed with markers on the side of the
screen. When using the Gesture Presenter feature, the image is slightly
smaller.
one of the following markers on the screen with your hand.
f Cover
Remove your hand while the color of the icon next to the marker is
changing.
• To move to the next slide or page, cover the marker next to the
icon.
• To move to the previous slide or page, cover the marker next to the
icon.
• Stand away from the markers to prevent them from being
covered accidentally when you do not want to perform the
operations.
• The markers are not available for the following input sources.
• HDBaseT
• Computer (component video)
• Video
• USB-A
• LAN (Epson iProjection)
• Screen Mirroring (if the device does not support User
Interface Back Channel (UIBC))
• For HDMI and Computer (RGB) image sources, you can use
the markers with Windows 2000 and later, or OS X 10.5.x and
later.
g To close the Gesture Presenter, press the [Gesture] button.
a
You can also close the Gesture Presenter by pressing the [Screen
Fit] button on the control panel, or by selecting Start/Stop in the
projector's Settings menu.
s Settings > Gesture Presenter > Start/Stop
g Related Links
• "Gesture Presenter Restrictions" p.79
Gesture Presenter Restrictions
Operating restrictions
You cannot change the following settings while using the Gesture Presenter
feature.
• Auto Source Search (set to Off automatically)
• Auto Iris (set to Off automatically)
Controlling a Presentation with Your Hands
• Light Optimizer (set to Off automatically)
• Power Consumption
• Multi-Projection
Functional restrictions
When you perform the following full screen functions, the Gesture Presenter
feature is temporarily canceled. After finishing these functions, you can use
the Gesture Presenter feature again.
•
•
•
•
•
•
Home screen
Test Pattern
Split Screen
User's Logo
Schedule Settings
Message Broadcasting
When you move the projector or perform the following image shape
adjustments, the Gesture Presenter feature stops. To use the Gesture Presenter
feature again, restart the feature after finishing the adjustments.
•
•
•
•
•
•
•
Screen Fit
Keystone adjustment
Quick Corner
Focus Help
Projection
Reset
Reset All
At high altitudes or locations subject to high temperatures, the image may
become darker and the Gesture Presenter feature may stop. To use the
Gesture Presenter feature again, restart the feature after cooling down the
projector.
80
Shutting Off the Image and Sound Temporarily
You can temporarily turn off the projected image and sound if you want to
redirect your audience's attention during a presentation. Any sound or video
action continues to run, however, so you cannot resume projection at the
point that you stopped it.
a
If you want to display an image such as a company logo or picture
when the [A/V Mute] button is pressed, you can select the screen
displayed in the A/V Mute setting in the projector's Extended menu.
s Extended > Display > A/V Mute
the [A/V Mute] button on the remote control to temporarily stop
a Press
projection and mute any sound.
b To turn the image and sound back on, press [A/V Mute] again.
81
a
• You can also stop projection using the A/V Mute slide lever on the
projector.
• The projector's power automatically turns off 30 minutes after A/V
Mute is enabled. You can disable this feature in the projector's ECO
menu.
s ECO > Lens Cover Timer
s ECO > A/V Mute Timer
• The lamp is still operating during A/V Mute, so the lamp hours
continue to accumulate.
g Related Links
• "Projector Setup Settings - Extended Menu" p.147
• "Projector Setup Settings - ECO Menu" p.159
Stopping Video Action Temporarily
You can temporarily stop the action in a video or computer presentation and
keep the current image on the screen. Any sound or video action continues to
run, however, so you cannot resume projection at the point that you stopped
it.
the [Freeze] button on the remote control to stop the video
a Press
action.
b To restart the video action in progress, press [Freeze] again.
82
Zooming Images
You can draw attention to parts of a presentation by zooming into a portion
of the image and enlarging it on the screen.
83
The enlarged image is projected and the enlargement ratio is displayed
on the screen.
The selected area can be enlarged to between one to four times in 25
incremental steps.
When projecting images from an Epson document camera using a USB
connection, you can enlarge the selected area from one to eight times
its size in 57 incremental steps.
a Press the [E-Zoom] + button on the remote control.
You see a crosshair on the screen indicating the center of the zoom
area.
the following buttons on the remote control to adjust the zoomed
b Use
image:
• Use the arrow buttons to position the crosshair in the image area you
want to zoom into. To move the crosshair diagonally, press any pair
of adjacent arrow buttons at the same time.
• Press the [E-Zoom] + button repeatedly to zoom into the image area.
Press and hold the [E-Zoom] + button to zoom in more quickly.
• To pan around the zoomed image area, use the arrow buttons.
• To zoom out of the image, press the [E-Zoom] – button.
• To return to the original image size, press [Esc].
Using the Remote Control as a Wireless Mouse
You can use the projector's remote control as a wireless mouse so you can
control projection at a distance from the computer.
a
84
the following buttons on the remote control to control your
d Use
presentation:
You can use the wireless mouse features with Windows Vista and later,
or OS X 10.7.x and later.
the projector to a computer using the projector's USB-B,
a Connect
Computer, or HDMI port.
a
The wireless mouse function does not work when projecting
images from a device connected to the HDMI1/MHL port using
an MHL cable.
connected your computer to the port other than the USB-B port,
b Ifalsoyouconnect
a USB cable to the projector's USB-B port and to a USB
port on your computer (for wireless mouse support).
c Start your presentation.
• To move through slides or pages, press the [Page] up or down
buttons.
• To move the cursor on the screen, use the arrow buttons. To move
the cursor diagonally, press any pair of adjacent arrow buttons at the
same time.
• To left-click, press the [Enter] button once (press it twice to doubleclick). To right-click, press the [Esc] button.
• To drag-and-drop, hold the [Enter] button as you move the cursor
with the arrow buttons, then release [Enter] at the destination.
a
• If the mouse button settings are set to reverse on the computer, the
operation of the remote control buttons is also reversed.
• The Wireless Mouse function does not work under the following
conditions:
• When the projector's menu or a Help screen is displayed.
• When operating functions other than the Wireless Mouse function
(such as adjusting the volume).
However, when using the E-Zoom or Pointer function, the page up
or down function is available.
Using the Remote Control as a Wireless Mouse
g Related Links
• "Zooming Images" p.83
• "Using the Remote Control as a Pointer" p.86
85
Using the Remote Control as a Pointer
You can use the projector's remote control as a pointer to help you focus your
audience on important information on the screen. The default pointer shape
is an arrow. You can change the shape in the Pointer Shape setting in the
projector's Settings menu.
a Press the [Pointer] button on the remote control.
the arrow buttons to move the pointer on the screen. To move the
b Use
pointer diagonally, press any pair of adjacent arrow buttons at the same
time.
c Press [Esc] to remove the pointer from the screen.
86
g Related Links
• "Projector Feature Settings - Settings Menu" p.145
Saving a User's Logo Image
You can save an image on the projector and display it whenever the projector
turns on. You can also display the image when the projector is not receiving
an input signal or when you temporarily stop projection (using A/V Mute).
This image is called the user's logo screen.
87
d Select User's Logo and press [Enter].
You can select a photo, graphic, or company logo as the user's logo, which is
useful in identifying the projector's owner to help deter theft. You can prevent
changes to the user's logo by setting up password protection.
a
• Once you save a user's logo, you cannot return to the factory default
logo.
• If the User's Logo Protection setting is set to On in the Password
Protection setting menu, set to Off before saving the user's logo.
• When you copy the menu settings from one projector to another
using the batch setup feature, user's logo is also copied. Do not
register the information that you do not want to share between
multiple projectors as a user's logo.
a
b Press the [Menu] button on the control panel or remote control.
c Select the Extended menu and press [Enter].
Display the image you want to project as the user's logo.
You see a prompt asking if you want to use the displayed image as a
user's logo.
a
Adjustments such as Keystone, E-Zoom, or Aspect are
temporarily canceled when you select User's Logo.
Yes and press [Enter].
e Select
You see a selection box overlaying your image.
a
Depending on the current image signal, the screen size may
change to match the resolution of the image signal.
Saving a User's Logo Image
the arrow buttons to surround the image area you want to use as
f Use
the user's logo and press [Enter].
You see a prompt asking if you want to select this image area.
a
You cannot change the image area size (400 × 300 pixels).
Yes and press [Enter]. (If you want to change the selected area,
g Select
select No, press [Enter], and repeat the last step.)
You see the User's Logo zoom factor menu.
h Select a zoom percentage and press [Enter].
You see a prompt asking if you want to save the image as the user's
logo.
88
Yes and press [Enter].
i Select
The user's logo is overwritten and a completion message appears.
j Press [Esc] to exit the message screen.
k Select the Extended menu and press [Enter].
l Select Display and press [Enter].
when you want to display the User's Logo screen:
m Select
• To display it whenever there is no input signal, select Display
Background and set it to Logo.
• To display it whenever you turn the projector on, select Startup
Screen and set it to On.
• To display it whenever you press the [A/V Mute] button, select A/V
Mute and set it to Logo.
To prevent anyone from changing the User's Logo settings without first
entering a password, set the User's Logo Protection setting to On in the
Password Protection setting menu and set the password.
g Related Links
• "Shutting Off the Image and Sound Temporarily" p.81
• "Selecting Password Security Types" p.95
Using Multiple Projectors
You can combine the projected images from two or more projectors to create
one large image.
89
a
• In some cases the brightness and color tone may not match
completely even after correction.
• If brightness and color tone differences become more noticeable over
time, repeat the adjustments.
g Related Links
• "Setting the Projector ID" p.89
• "Selecting the Projector You want to Operate" p.90
• "Matching the Image Colors" p.91
• "Adjusting RGBCMY" p.92
Setting the Projector ID
a
• Before starting projection, make sure you set Multi-Projection to On
for all of the projectors.
s Extended > Multi-Projection > Multi-Projection
• Before starting projection, make sure you select the same color mode
for all of the projectors.
s Image > Color Mode
g Related Links
• "Projector Identification System for Multiple Projector Control" p.89
Projector Identification System for Multiple Projector
Control
When lining up multiple projectors to project images, you can correct the
brightness and color tone of each projector's image so that the images match
closely.
You can set a unique projector ID for each projector to operate them
individually using a remote control, and then correct the brightness and color
for each projector.
To control multiple projectors from a remote control, give each projector a
unique ID.
a Press the [Menu] button on the control panel or remote control.
b Select the Extended menu and press [Enter].
c Select Multi-Projection and press [Enter].
d Select Projector ID and press [Enter].
Using Multiple Projectors
the arrow buttons to select the identification number you want to
e Use
use for the projector. Then press [Enter].
90
The current Projector ID is displayed on the projected screen. It
disappears after about 3 seconds.
holding the [ID] button, press the number button that matches
b While
the ID of the projector you want to operate.
f Press [Menu] or [Esc] to exit the menus.
Repeat these steps for all the other projectors you want to operate from one
remote control.
Selecting the Projector You want to Operate
After setting the projector's ID, select the ID for the projector you want to
operate using the remote control.
the remote control at the target projector and press the [ID]
a Aim
button.
The projector you want to operate is selected.
the [ID] button to check if the ID-setting process worked.
c Press
You see a message displayed by the projector.
• If the remote control is listed as On, you can operate the projector
from the remote control.
• If the remote control is listed as Off, you cannot operate the projector
from the remote control. Repeat the steps above to enable the remote
control.
Using Multiple Projectors
a
• When you select 0 on the remote control, you can operate all
projectors regardless the Projector ID setting.
• You must select the projector ID from the remote control each
time you turn on the projector you have set it to control. When
you turn on the projector, 0 is selected as the remote control's
projector ID.
• When you set the Projector ID setting to Off, you can operate
the projector using the remote control whichever ID you select
on the remote control.
91
b Select Multi-Projection and press [Enter].
Matching the Image Colors
You can match the display quality of multiple projectors that will project next
to each other.
Turn on all the projectors and select the Color Matching setting in each
projector's Extended menu so that all the projectors' display quality match on
the combined screen.
c Select Color Matching and press [Enter].
a Press the [Menu] button, select the Extended menu, and press [Enter].
d Select Adjustment Level.
Using Multiple Projectors
There are six adjustment levels from white through gray, and up to
black. You can adjust each level individually.
e Select Red, Green, or Blue, and adjust the color tone.
f Select Brightness, and adjust the value.
g Return to step 4 and adjust another level.
h Press the [Esc] button to return to the previous screen.
Adjusting RGBCMY
You can adjust the Hue, Saturation, and Brightness settings for R (red), G
(green), B (blue), C (cyan), M (magenta), and Y (yellow) color components.
Turn on all the projectors and select the RGBCMY setting in each projector's
Extended menu so that the color tone on the combined screen becomes
entirely even.
92
a Press the [Menu] button, select the Extended menu, and press [Enter].
b Select Multi-Projection and press [Enter].
Using Multiple Projectors
c Select RGBCMY and press [Enter].
d Select the color to adjust, and press [Enter].
the following as necessary for each setting:
e Do
• To adjust the overall hue of the color, bluish - greenish - reddish,
adjust the Hue setting.
• To adjust the overall vividness of the color, adjust the Saturation
setting.
• To adjust the overall color brightness of the color, adjust the
Brightness setting.
f Press [Menu] or [Esc] to exit the menus.
93
Projector Security Features
You can secure your projector to deter theft or prevent unintended use by
setting up the following security features:
• Password security to prevent people who do not know the password from
using the projector, and prevent changes to the startup screen and other
settings.
This acts as an anti-theft function as the projector cannot be used even if it
is stolen, and you can limit who can use the projector.
• Button lock security to block operation of the projector using the buttons
on the control panel.
This is useful at events or shows when you want to deactivate all buttons
during projection or at schools when you want to limit button operation.
• Security cabling to physically secure the projector in place.
g Related Links
• "Password Security Types" p.94
• "Locking the Projector's Buttons" p.97
• "Installing a Security Cable" p.98
94
2245U/EB-2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EBX500KG).
• Screen Mirroring Protec. password prevents anyone from changing the
projector's Screen Mirroring settings (EB-2265U/EB-2255U/EB-2165W).
g Related Links
• "Setting a Password" p.94
• "Selecting Password Security Types" p.95
• "Entering a Password to Use the Projector" p.96
Setting a Password
To use password security, you must set a password.
a
The default password is set to "0000". Change this to your own
password.
down the [Freeze] button on the remote control for about 5
a Hold
seconds.
Password Security Types
You can set up the following types of password security using one shared
password:
• Power On Protection password prevents anyone from using the projector
without first entering a password. When plugging the power cord and
turning on the projector at first time, you must enter the correct password.
This also applies to Direct Power On and Auto Power On.
• User's Logo Protection password prevents anyone from changing the
custom screen displayed when the projector turns on, when no signal is
being input, or when you use the A/V Mute feature. The custom screen
discourages theft by identifying the projector's owner.
• Network Protection password prevents anyone from changing the
projector's Network settings.
• Schedule Protection password prevents anyone from changing the
projector's schedule settings (EB-2265U/EB-2255U/EB-2250U/EB-
You see the Password Protection setting menu.
a
If Password Protection is already activated, you must enter the
correct password to display the Password Protection setting
menu.
Projector Security Features
b Select Password and press [Enter].
95
the password again.
e Enter
You see the message "Password accepted". If you enter the password
incorrectly, a message is displayed prompting you to re-enter the
password.
f Press [Esc] to return to the menu.
g Make a note of the password and keep it in a safe place.
Selecting Password Security Types
You see the prompt "Change the password?".
After setting a password, you see this menu, allowing you to select the
password security types you want to use.
c Select Yes and press [Enter].
a
If you select No, the Password Protection setting menu is
displayed again.
down the [Num] button on the remote control and use the
d Hold
numeric buttons to set a four-digit password.
If you do not see this menu, hold down the [Freeze] button on the remote
control for 5 seconds until the menu appears.
The password displays as **** as it is entered. A confirmation prompt is
displayed when you enter the fourth digit.
• To prevent unauthorized use of the projector, select On as the Power On
Protection setting.
• To prevent changes to the User's Logo screen or related display settings,
select On as the User's Logo Protection setting.
• To prevent changes to network settings, select On as the Network
Protection setting.
• To prevent changes to the projector's schedule settings, select On as the
Schedule Protection setting (EB-2265U/EB-2255U/EB-2250U/EB-
Projector Security Features
2245U/EB-2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EBX500KG).
• To prevent changes to the projector's Screen Mirroring settings, select On as
the Screen Mirroring Protec. setting (EB-2265U/EB-2255U/EB-2165W).
96
down the [Num] button on the remote control while you enter
a Hold
the password using the numeric buttons.
You can attach the password protect sticker to the projector as an additional
theft deterrent.
a
Be sure to keep the remote control in a safe place; if you lose it, you will
not be able to enter the password.
Entering a Password to Use the Projector
When the password screen is displayed, enter the correct password.
The password screen closes.
the password is incorrect, you see a message and a prompt to try
b Ifagain.
Enter the correct password to proceed.
Attention
• If an incorrect password is entered three times in succession, the message
"The projector's operation will be locked." is displayed for approximately
5 minutes, and the projector switches to standby mode. If this happens,
disconnect the power plug from the electrical outlet, reinsert it, and turn
the projector back on. The projector displays the password entry screen
again so that you can enter the correct password.
• If you have forgotten the password, make a note of the "Request Code:
xxxxx" number that appears on the screen and contact Epson for help.
• If you continue to repeat the above operation and input the wrong
password 30 times in succession, the message "The projector's operation
will be locked. Contact Epson as described in your documentation." is
displayed and the projector does not accept any more password entries.
Contact Epson for help.
Projector Security Features
Locking the Projector's Buttons
97
c Select Lock Setting and press [Enter].
You can lock the buttons on the control panel to prevent anyone from using
the projector. The projector can still be operated using the remote control.
a Press the [Menu] button on the control panel or remote control.
b Select the Settings menu and press [Enter].
d Select Control Panel Lock and press [Enter].
one of these lock types and press [Enter]:
e Select
• To lock all of the projector's buttons, select Full Lock.
• To lock all buttons except the power button, select Partial Lock.
Projector Security Features
You see a confirmation prompt.
Yes and press [Enter].
f Select
The Control Panel Lock setting takes effect.
98
• Use the security cable attachment point on the projector to attach a wire
cable and secure it to a room fixture or heavy furniture.
g Related Links
• "Unlocking the Projector's Buttons" p.98
Unlocking the Projector's Buttons
If the projector's buttons have been locked, do one of the following to unlock
them.
• Hold down the [Enter] button on the control panel for 7 seconds. A
message is displayed and the lock is released.
• Select Off as the Control Panel Lock setting in the projector's Settings
menu.
s Settings > Lock Setting > Control Panel Lock
g Related Links
• "Projector Feature Settings - Settings Menu" p.145
Installing a Security Cable
You can install the security cable on the projector to deter theft.
• Use the security slot on the projector to attach a Kensington Microsaver
Security system.
a
For more details on the Microsaver Security System, see
http://www.kensington.com/.
a
You can use a commercially available theft-prevention wire lock. See
the documentation supplied with the wire lock for locking
instructions.
Using the Projector on a Network
Follow the instructions in these sections to set up your projector for use on a network.
g Related Links
• "Wired Network Projection" p.100
• "Wireless Network Projection" p.103
• "Wireless Network Projection from a Mobile Device (Screen Mirroring)" p.113
• "Secure HTTP" p.118
Wired Network Projection
You can send images to your projector through a wired network. To do this,
connect the projector to your network, and then set up your projector and
computer for network projection.
After connecting and setting up the projector as described here, install
EasyMP Multi PC Projection from the Epson Projector Software CD-ROM (if
available) or Web site.
EasyMP Multi PC Projection software sets up your computer for network
projection. It also allows you to hold interactive meetings by projecting user's
computer screens over a network. See the EasyMP Multi PC Projection
Operation Guide for instructions.
g Related Links
• "Connecting to a Wired Network" p.100
• "Selecting Wired Network Settings" p.100
100
Selecting Wired Network Settings
Before you can project from computers on your network, you need to select
network settings on the projector.
a
Make sure you already connected the projector to your wired network
using the LAN port.
a Press the [Menu] button on the control panel or remote control.
b Select the Network menu and press [Enter].
Connecting to a Wired Network
To connect the projector to a wired local area network (LAN), use a 100BaseTX or 10Base-T network cable. To ensure proper data transmission, use a
Category 5 shielded cable or better.
one end of the network cable to your network hub, switch, or
a Connect
router.
b Connect the other end of the cable to the projector's LAN port.
c Select Network Configuration and press [Enter].
Wired Network Projection
d Select the Basic menu and press [Enter].
101
• Display LAN Info. lets you set the display format for the projector's
network information.
a
Use the displayed keyboard to enter the name, passwords and
keyword. Press the arrow buttons on the remote control to
highlight characters and press [Enter] to select them.
f Select the Wired LAN menu and press [Enter].
the basic options as necessary.
e Select
• Projector Name lets you enter a name up to 16 alphanumeric
characters long to identify the projector over the network.
• PJLink Password lets you enter a password up to 32 alphanumeric
characters long for using the PJLink protocol for projector control.
• Remote Password lets you enter a password up to 8 alphanumeric
characters long for accessing the projector using the Basic Control.
(User name is EPSONREMOTE; default password is guest.)
• Web Control Password lets you enter a password up to 8
alphanumeric characters long for accessing the projector over the
Web. (User name is EPSONWEB; default password is admin.)
• Moderator Password lets you enter a four-digit number password
for accessing the projector as a moderator using EasyMP Multi PC
Projection or Epson iProjection. (No password is set by default.)
• Projector Keyword lets you turn on a security password to prevent
access to the projector by anyone not in the room with it. You must
enter a displayed, randomized keyword from a computer using
EasyMP Multi PC Projection or Epson iProjection to access the
projector and share the current screen.
the IP settings for your network as necessary.
g Assign
• If your network assigns addresses automatically, select IP Settings to
set the DHCP setting to On.
• If you must set addresses manually, select IP Settings to set the
DHCP setting to Off, and then enter the projector's IP Address,
Subnet Mask, and Gateway Address as necessary.
• If you want to connect the projector to the network using IPv6, select
IPv6 Settings to set the IPv6 setting to On, and then set the Auto
Configuration and Use Temporary Address settings as necessary.
Wired Network Projection
a
To highlight the numbers you want from the displayed keyboard,
press the arrow buttons on the remote control. To select a
highlighted number, press [Enter].
prevent the IP address from being displayed on the LAN standby
h Toscreen
and Home screen, set the IP Address Display setting to Off.
you finish selecting settings, select Complete and follow the oni When
screen instructions to save your settings and exit the menus.
the [LAN] button on the remote control.
j Press
The wired network settings complete when you see the correct IP
address on the LAN standby screen.
102
Wireless Network Projection
You can send images to your projector through a wireless network.
To do this, you must install the Epson 802.11b/g/n wireless LAN module, and
then set up your projector and computer for wireless projection.
You can connect the projector to your wireless network by configuring the
connection manually using the projector's Network menus.
After installing the wireless LAN module and setting up the projector, install
the network software from the Epson Projector Software CD-ROM (if
available) or download the software, as necessary. Use the following software
and documentation to set up and control wireless projection:
• EasyMP Multi PC Projection software allows you to hold interactive
meetings by projecting the computer screens of users over a network. See
the EasyMP Multi PC Projection Operation Guide for instructions.
• Epson iProjection app allows you to project from iOS or Android devices.
You can download Epson iProjection from App Store or Google play. Any
fees incurred when communicating with App Store or Google play are the
responsibility of the customer.
g Related Links
• "Installing the Wireless LAN Module" p.103
• "Installing the Wireless LAN Module into the Rear USB-A Port" p.104
• "Selecting Wireless Network Settings Manually" p.105
• "Selecting Wireless Network Settings in Windows" p.108
• "Selecting Wireless Network Settings in OS X" p.108
• "Setting Up Wireless Network Security" p.108
• "Using a QR Code to Connect a Mobile Device" p.110
• "Using a USB Key to Connect a Windows Computer" p.111
Installing the Wireless LAN Module
To use the projector over a wireless network, install the Epson 802.11b/g/n
wireless LAN module (EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG). Do not
install any other type of wireless LAN module.
103
Attention
Never remove the module while its indicator is green or flashing, or while you are
projecting wirelessly. This could damage the module or lose data.
a Turn off the projector and unplug the power cord.
b Slide the air filter cover latch and open the air filter cover.
Wireless Network Projection
104
the screw securing the wireless LAN module stopper and
c Remove
remove the stopper.
the wireless LAN module stopper, and secure it using the screw
e Replace
you removed.
d
f Close the air filter cover.
g Plug in and turn on the projector.
Insert the wireless LAN module into the port.
Installing the Wireless LAN Module into the Rear
USB-A Port
To use the projector over a wireless network, install the Epson 802.11b/g/n
wireless LAN module (EB-2140W/EB-2040). Do not install any other type of
wireless LAN module.
Attention
Never remove the module while its indicator is blue or flashing, or while you are
projecting wirelessly. This could damage the module or lose data.
Wireless Network Projection
a cross-head screwdriver to remove the screw that secures the
a Use
wireless LAN module cover.
b Connect the wireless LAN module to the USB-A port.
105
the wireless LAN module cover, and secure it in place with the
c Attach
screw.
Selecting Wireless Network Settings Manually
Before you can project from your wireless network, you need to select
network settings for the projector.
a Press the [Menu] button on the control panel or remote control.
Wireless Network Projection
106
b Select the Network menu and press [Enter].
e Select the Basic menu and press [Enter].
c Select On as the Wireless LAN Power setting.
the basic options as necessary.
f Select
• Projector Name lets you enter a name up to 16 alphanumeric
characters long to identify the projector over the network.
• PJLink Password lets you enter a password up to 32 alphanumeric
characters long for using the PJLink protocol for projector control.
• Remote Password lets you enter a password up to 8 alphanumeric
characters long for accessing the projector using the Basic Control.
(User name is EPSONREMOTE; default password is guest.)
• Web Control Password lets you enter a password up to 8
alphanumeric characters long for accessing the projector over the
Web. (User name is EPSONWEB; default password is admin.)
• Moderator Password lets you enter a four-digit number password
for accessing the projector as a moderator using EasyMP Multi PC
Projection or Epson iProjection. (No password is set by default.)
d Select Network Configuration and press [Enter].
• Projector Keyword lets you turn on a security password to prevent
access to the projector by anyone not in the room with it. You must
enter a displayed, randomized keyword from a computer using
EasyMP Multi PC Projection or Epson iProjection to access the
projector and share the current screen.
Wireless Network Projection
• Display LAN Info. lets you set the display format for the projector's
network information.
a
Use the displayed keyboard to enter the name and password.
Press the arrow buttons on the remote control to highlight
characters and press [Enter] to select them.
g Select the Wireless LAN menu and press [Enter].
107
the Advanced connection mode, assign the IP settings for your
j For
network as necessary.
• If your network assigns addresses automatically, select IP Settings to
set the DHCP setting to On.
• If you must set addresses manually, select IP Settings to set the
DHCP setting to Off, and then enter the projector's IP Address,
Subnet Mask, and Gateway Address as necessary.
• If you want to connect the projector to the network using IPv6, select
IPv6 Settings to set the IPv6 setting to On, and then set the Auto
Configuration and Use Temporary Address settings as necessary.
prevent the SSID or IP address from being displayed on the LAN
k Tostandby
screen and Home screen, set the SSID Display setting or the IP
Address Display setting to Off.
you have finished selecting settings, select Complete and then
l When
follow the on-screen instructions to save your settings and exit the
menus.
the [LAN] button on the remote control.
m Press
The wireless network settings are complete when you see the correct IP
address on the LAN standby screen.
the Connection Mode setting.
h Select
• Quick lets you connect to multiple smartphones, tablets, or
computers directly using wireless communication.
• Advanced lets you connect to smartphones, tablets, or computers
over a wireless network access point.
you selected the Advanced connection mode, select Search Access
i IfPoint
to select the access point you want to connect to.
a
If you need to assign the SSID manually, select SSID to enter the
SSID.
Wireless Network Projection
When you have finished making wireless settings for your projector, you need
to select the wireless network on your computer. Then start the network
software to send images to your projector through a wireless network.
Selecting Wireless Network Settings in Windows
Before connecting to the projector, select the correct wireless network on your
computer.
a
connecting in Advanced connection mode, select the network
b When
name (SSID) of the network the projector is connecting to.
c Click Connect.
To access your wireless utility software, double-click the network icon
on the Windows taskbar.
Selecting Wireless Network Settings in OS X
Before connecting to the projector, select the correct wireless network in OS
X.
a Click the AirPort icon on the menu bar at the top of the screen.
connecting in Advanced connection mode, make sure AirPort is
b When
turned on and select the network name (SSID) of the network the
projector is connecting to.
Setting Up Wireless Network Security
You can set up security for your projector to use on a wireless network. Set up
one of the following security options to match the settings used on your
network:
108
•
•
•
•
WPA2-PSK security
WPA2-EAP security * **
WPA/WPA2-PSK security *
WPA/WPA2-EAP security * **
* Only available for the Advanced connection mode.
** Only available for EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG.
a
Contact your network administrator for guidance on entering the
correct information.
you want to set up the WPA2-EAP or WPA/WPA2-EAP security,
a Ifmake
sure your digital certificate file is compatible with projector
registration and placed directly on the USB storage device.
b Press the [Menu] button on the control panel or remote control.
c Select the Network menu and press [Enter].
d Select Network Configuration and press [Enter].
Wireless Network Projection
e Select the Wireless LAN menu and press [Enter].
109
one of the following according to the security you selected.
h Do
• WPA2-PSK, WPA/WPA2-PSK: Select Complete and follow the onscreen instructions to save your settings and exit the menus.
• WPA2-EAP, WPA/WPA2-EAP: Select EAP Method and press
[Enter].
i Select the protocol for authentication as the EAP Type setting.
import your certificate, select the certificate type and press [Enter].
j To• Client
Certificate for the PEAP-TLS or EAP-TLS type
• CA certificate for the PEAP, PEAP-TLS, EAP-TLS, or EAP-FAST
type
a
f
Select the Security setting and press [Enter].
You can also register the digital certificates from your Web
browser. However, be sure to register just once or the certificate
may not install correctly.
k Select Register and press [Enter].
the on-screen instructions to connect a USB storage device to
l Follow
the projector's USB-A port.
m Press [Enter] to display the certificate list.
the certificate to import using the displayed list.
n Select
A message is displayed prompting you to enter the password for the
certificate.
a password and press [Enter].
o Enter
The certificate is imported and a completion message appears.
g Select the security settings to match your network settings.
your EAP settings as necessary.
p Select
• User name lets you enter a user name using up to 64 alphanumeric
characters. To enter more than 32 characters, use your Web browser.
Wireless Network Projection
When importing a client certificate, the name the certificate was
issued to is automatically set.
• Password lets you enter a password using up to 64 alphanumeric
characters for authentication when using the PEAP, EAP-FAST, or
LEAP type. To enter more than 32 characters, use your Web
browser.
• Verify Server Cert. lets you select whether or not to verify the server
certificate when a CA certificate has been set.
• RADIUS Serv.Name lets you enter the server name to be verified.
110
Client Certificate (PEAP-TLS/EAP-TLS)
Specification
Description
Format
PKCS#12
Extension
PFX, P12
Encryption
RSA
Hashes
MD5/SHA-1/SHA-256/SHA-384/SHA-512
Key length
512/1024/2048/4096 bit
Password *
Up to 32 alphanumeric characters; required
CA Certificate (PEAP/PEAP-TLS/EAP-TLS/EAP-FAST)
q
When you have finished making settings, select Complete and follow
the on-screen instructions to save your settings and exit the menus.
g Related Links
• "Supported Client and CA Certificates" p.110
• "Network Menu - Wireless LAN Menu" p.153
Supported Client and CA Certificates
You can register these types of digital certificates.
Specification
Description
Format
X509v3
Extension
DER/CER/PEM
Encryption
RSA
Hashes
MD5/SHA-1/SHA-256/SHA-384/SHA-512
Key length
512/1024/2048/4096 bit
Encoding
BASE64/Binary
* You can set a password using up to 64 alphanumeric characters. However,
you need to use your Web browser to enter more than 32 characters.
Using a QR Code to Connect a Mobile Device
After selecting the wireless network settings for your projector, you can
display a QR code on the screen and use it to connect a mobile device using
the Epson iProjection app.
Wireless Network Projection
a
111
• Make sure you have installed the latest version of Epson iProjection
on your device (V1.3.0 or later supports this feature).
• You can download Epson iProjection for free from App Store or
Google play. Any fees incurred when communicating with App Store
or Google play are the responsibility of the customer.
• When using Epson iProjection in Quick connection mode, we
recommend making security settings.
a
• If you do not see the QR code, set the Display LAN Info.
setting to Text & QR Code in the projector's Network menu.
s Network > Network Configuration > Basic > Display
LAN Info.
• To hide the QR code, press the [Esc] button.
• When the QR code is hidden, press the [Enter] button to
display the code.
• You can also display the QR code by selecting the icon on the
Home screen.
b Start Epson iProjection on your mobile device.
the projected QR code using Epson iProjection to connect it to
c Read
the projector.
a
To correctly read the QR code, make sure you face the screen
squarely and closely enough so that the projected code fits into
the guide of the mobile device's QR code reader. If you are too
far from the screen, the code may not be read.
When a connection is established, select Contents menu from
then select the file you want to project.
You can set up your USB flash drive as a USB key to quickly connect the
projector to a wireless LAN supported Windows computer. The USB key
allows you to automatically select a computer's wireless network settings and
project your presentation wirelessly.
a Set up the USB key using EasyMP Multi PC Projection.
the [LAN] button on the remote control.
a Press
The QR code is displayed on the projected surface.
a
Using a USB Key to Connect a Windows Computer
, and
See the EasyMP Multi PC Projection Operation Guide for
instructions.
sure the wireless LAN module is installed or built into your
b Make
projector.
c Turn on the projector.
the [LAN] button on the remote control.
d Press
The LAN standby screen is displayed. Verify that an SSID and IP
address are displayed.
one of the following to connect the USB key.
e Do
• Connect the USB key to the projector's USB-A port (EB-2265U/EB2255U/EB-2250U/EB-2245U/EB-2165W/EB-2155W/EB-2065/EB2055/EB-X550KG/EB-X500KG).
• Remove the wireless LAN module from the projector and insert the
USB key into the same port used for the wireless LAN module (EB2140W/EB-2040).
You see a projected message that the network information update is
complete.
the USB key.
f Remove
If your projector needs the wireless LAN module, reinsert the wireless
LAN module into the projector.
Wireless Network Projection
g Connect the USB key to a USB port on your computer.
a
In Windows Vista, if the AutoPlay window is displayed, select
MPPLaunch.exe, then select Allow.
h Follow the on-screen instructions to install the necessary application.
a
• If the Windows Firewall message is displayed, click Yes to
disable the firewall.
• You need administrator authority to install the software.
• If it is not installed automatically, double-click
MPPLaunch.exe in the USB key.
After a few minutes, your computer image is displayed by the projector.
If it does not appear, press the [LAN] button on your projector's
remote control or restart your computer.
i Run your presentation.
you have finished projecting wirelessly, select the Safely Remove
j When
Hardware option in the Windows taskbar, and then remove the USB
key from your computer.
a
You may need to restart your computer to reactivate your
wireless LAN connection.
112
Wireless Network Projection from a Mobile Device (Screen Mirroring)
You can send image to your projector from mobile devices such as laptops,
smartphones, and tablets using Miracast technology (EB-2265U/EB2255U/EB-2165W).
If your device supports Miracast, you do not need to install any additional
software. When using a Windows computer, make sure the necessary adapter
for the Miracast connection is available.
Note the following limitations when using Screen Mirroring features.
• You cannot play an interlaced image.
• You cannot play multi-channel audio over 3ch (channel 3).
• You cannot project images with a resolution above 1920 × 1080 and a frame
rate above 30 fps.
• You cannot play 3D video.
• You may not be able to view contents with copyright protection with a
Miracast connection depending on your device.
• Do not change the projector's Screen Mirroring Settings during Screen
Mirroring projection. Doing so may cause the projector to disconnect and it
may take a while to re-connect.
s Network > Screen Mirroring Settings
• Do not turn off the projector directly by the breaker during Screen
Mirroring projection.
a
Mobile devices with Android installed or Windows 8.1 or later installed
mainly support Miracast.
Support for Miracast varies depending on the mobile device. See your
mobile device manual for details.
g Related Links
• "Selecting Screen Mirroring Settings" p.113
• "Connecting Using Screen Mirroring in Windows 10" p.115
• "Connecting Using Screen Mirroring in Windows 8.1" p.116
• "Connecting Using Screen Mirroring with the Miracast Function" p.117
113
Selecting Screen Mirroring Settings
You must select Screen Mirroring settings for your projector to project images
from your mobile device.
a
If you set a Screen Mirroring Protec. password, turn off your Screen
Mirroring Protec. password first.
a Press the [Menu] button on the control panel or remote control.
b Select the Network menu and press [Enter].
Wireless Network Projection from a Mobile Device (Screen Mirroring)
c Select On as the Screen Mirroring setting.
114
e Set the Display Name setting as necessary.
the Operation Mode setting.
f Select
• Basic lets you connect with basic options.
d Select Screen Mirroring Settings and press [Enter].
• Extended lets you connect with advanced options.
the Basic setting as necessary.
g Select
• Wireless LAN Sys. lets you select the type of wireless LAN system
the projector is connecting to.
• Adjust Image Quality lets you adjust the screen mirroring
speed/quality. Select a small number to improve the quality and
select large number to increase the speed.
• Connection Mode lets you select the type of WPS (Wi-Fi Protected
Setup). Available only for the Basic operation mode.
the Extended operation mode, select the Extended setting.
h For
• Meeting Mode lets you select the type of meeting. Select
Interruptions OK to connect to another mobile device during
Screen Mirroring projection or No Interruptions to exclusively
connect to one device.
• Channel lets you select the wireless channel used by Screen
Mirroring.
Wireless Network Projection from a Mobile Device (Screen Mirroring)
the Display setting as necessary.
i Select
• Display PIN Code lets you display the PIN code on the projected
115
c Display Action Center, and then select Connect.
image while projecting input sources other than Screen Mirroring.
• Display Device Name lets you display the newly connected device
name on the projected image.
you finish selecting settings, select Set and follow the on-screen
j When
instructions to save your settings and exit the menus.
the [Home] button on the control panel or remote control. The
k Press
settings are complete when you see the Display Name on the Home
screen.
Connecting Using Screen Mirroring in Windows 10
You can set up your computer for wireless projection and play audio through
the projector's speaker system by connecting using Screen Mirroring.
You see a list of available devices.
d Select the projector's Display Name from the list.
a Select Screen Mirroring Settings on your projector as necessary.
the [LAN] button on the remote control to switch to the Screen
b Press
Mirroring source.
You see the Screen Mirroring standby screen.
you see the PIN entry screen on your computer, enter the PIN code
e Ifdisplayed
on the Screen Mirroring standby screen or at the bottom
right of the projected image.
The projector displays the image from your computer.
Wireless Network Projection from a Mobile Device (Screen Mirroring)
a
It may take some time until the connection is established. While
connecting, do not disconnect the projector's power cord. Doing
so may cause your device to freeze or malfunction.
116
d Select Add a wireless display.
Connecting Using Screen Mirroring in Windows 8.1
You can set up your computer for wireless projection from Charms in
Windows 8.1. You can play audio through the projector's speaker system by
connecting using Screen Mirroring.
a Select Screen Mirroring Settings on your projector as necessary.
the [LAN] button on the remote control to switch to the Screen
b Press
Mirroring source.
You see the Screen Mirroring standby screen.
c
On your computer, select Devices from Charms and select Project.
You see a list of available devices.
e Select the projector's Display Name from the list.
you see the PIN entry screen on your computer, enter the PIN code
f Ifdisplayed
on the Screen Mirroring standby screen or at the bottom
right of the projected image.
The projector displays the image from your computer.
Wireless Network Projection from a Mobile Device (Screen Mirroring)
a
It may take some time until the connection is established. While
connecting, do not disconnect the projector's power cord. Doing
so may cause your device to freeze or malfunction.
Connecting Using Screen Mirroring with the Miracast
Function
If your mobile device such as a smartphone supports Miracast, you can
connect it to the projector wirelessly and project images. You can play audio
through the projector's speaker system by connecting using Screen Mirroring.
a Select Screen Mirroring Settings on your projector as necessary.
the [LAN] button on the remote control to switch to the Screen
b Press
Mirroring source.
You see the Screen Mirroring standby screen.
your mobile device, use your Miracast function to search for the
c On
projector.
You see a list of available devices.
d Select the projector's Display Name from the list.
see the PIN entry screen on your mobile device, enter the PIN
e Ifcodeyoudisplayed
on the Screen Mirroring standby screen or at the bottom
right of the projected image.
The projector displays the image from your mobile device.
a
It may take some time until the connection is established. While
connecting, do not disconnect the projector's power cord. Doing
so may cause your device to freeze or malfunction.
Depending on the mobile device, you may need to delete a device
when connecting. Follow the on-screen instructions on your
device.
117
Secure HTTP
You can use the HTTPS protocol to increase security between the projector
and a Web browser communicating with it (EB-2265U/EB-2255U/EB2250U/EB-2245U/EB-2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EBX500KG). To do this, you create a server certificate, install it on the projector,
and turn on the Secure HTTP setting in the projector menus to verify the
reliability of the Web browser.
118
e Select the Others menu and press [Enter].
s Network > Network Configuration > Others > Secure HTTP
Even if you do not install a server certificate, the projector automatically
creates a self-signed certificate and allows communication. However, because
the self-signed certificate cannot verify reliability from a Web browser, you
see a warning about the server's reliability when you access the projector from
a Web browser. This warning does not prevent communication.
g Related Links
• "Importing a Web Server Certificate Using the Menus" p.118
Importing a Web Server Certificate Using the Menus
You can create your Web server certificate, and import it using the projector
menus and a USB flash drive.
a
You can also register the digital certificates from your Web browser.
However, be sure to register just once or the certificate may not install
correctly.
sure your digital certificate file is compatible with projector
a Make
registration and directly placed on the USB storage device.
b Press the [Menu] button on the control panel or remote control.
c Select the Network menu and press [Enter].
d Select Network Configuration and press [Enter].
f Select On as the Secure HTTP setting.
g Select Web Server Cert. and press [Enter].
h Select Register and press [Enter].
the on-screen instructions to connect a USB storage device to
i Follow
the projector's USB-A port.
j Press [Enter] to display the certificate list.
the certificate to import using the displayed list.
k Select
A message is displayed prompting you to enter the password for the
certificate.
a password and press [Enter].
l Enter
The certificate is imported and a completion message appears.
Secure HTTP
119
g Related Links
• "Supported Web Server Certificates" p.119
Supported Web Server Certificates
You can register these types of digital certificates.
Web Server Certificate (Secure HTTP)
Specification
Description
Format
PKCS#12
Extension
PFX, P12
Encryption
RSA
Hashes
MD5/SHA-1/SHA-256/SHA-384/SHA-512
Key length
512/1024/2048/4096 bit
Common name
Network host name
Organization
Optional
Password *
Up to 32 alphanumeric characters; required
* You can set a password using up to 64 alphanumeric characters. However,
you need to use your Web browser to enter more than 32 characters.
Monitoring and Controlling the Projector
Follow the instructions in these sections to monitor and control the projector over a network.
g Related Links
• "EasyMP Monitor" p.121
• "Controlling a Networked Projector Using a Web Browser" p.122
• "Setting Up Projector Network E-Mail Alerts" p.126
• "Setting Up Monitoring Using SNMP" p.127
• "Using ESC/VP21 Commands" p.128
• "PJLink Support" p.130
• "Crestron RoomView Support" p.131
• "Setting Projector Event Schedules" p.135
EasyMP Monitor
EasyMP Monitor software (Windows only) lets you monitor and control your
projector through the network. See the EasyMP Monitor Operation Guide for
instructions.
You can download EasyMP Monitor from the following Web site.
http://www.epson.com/
121
Controlling a Networked Projector Using a Web Browser
122
Once you have connected your projector to your network, you can select
projector settings and control projection using a compatible Web browser.
This lets you access the projector remotely.
a
• Make sure the computer and projector are connected to the network.
When projecting images using a wireless LAN, connect in Advanced
connection mode.
• The Web setup and control features support Internet Explorer 9.0 or
later (Windows), and Safari (OS X) on networks that do not use a
proxy server for connection. You cannot select all of the projector
menu settings or control all projector functions using a Web
browser.
• If you set Standby Mode to Communication On in the projector's
ECO menu, you can use a Web browser to select settings and control
projection even if the projector is in standby mode (when the power
is off).
a Make sure the projector is turned on.
sure your computer or device is connected to the same network
b Make
as the projector.
c Start your Web browser on the computer or device.
to the Epson Web Control screen by entering the projector's IP
d Go
address into the browser's address box. When entering an IPv6 address,
wrap the address with [ and ].
You see the Epson Web Control screen.
e To control projection remotely, select Basic Control.
a
• If you see a log in window, enter your user name and
password. (The user name is EPSONREMOTE and the default
password is guest.)
• You can change the password in Remote Password in the
projector's Network menu.
s Network > Network Configuration > Basic > Remote
Password
Controlling a Networked Projector Using a Web Browser
the icon corresponding to the projector function you want to
f Select
control.
123
J Page up and down button controls
K Displays the QR code
L Volume button controls
M Selects the USB Display source
N Selects the USB device source
O Selects the HDBaseT source (EB-2265U/EB-2165W)
P Selects Computer1 port source
Q Searches for sources
select projector menu settings, select Advanced on the Epson Web
g ToControl
screen.
a
A Power button control
B Selects HDMI1 port source
C Selects HDMI2 port source
D Selects Computer2 port source
E Selects Video source
F Selects the network source
G Selects the Screen Mirroring source (EB-2265U/EB-2255U/EB-2165W)
H A/V Mute button control
I Freeze button control
• You can also change projector settings by accessing the
projector menu system from OSD Control Pad. See help on
how to use the OSD Control Pad screen.
• You may need to log in before you see the Advanced, OSD
Control Pad, or Test Pattern screen. If a login screen is
displayed, enter your user name and password. (The user name
is EPSONWEB and the default password is admin.)
• You can change the password in Web Control Password in
the projector's Network menu.
s Network > Network Configuration > Basic > Web
Control Password
the name of the menu and follow the on-screen instructions to
h Select
select settings.
Controlling a Networked Projector Using a Web Browser
a
• You cannot select the following settings using a Web browser.
• Gesture Presenter
• HDMI Link
• Pointer Shape
• User Button
• Test Pattern
• User's Logo
• Language
• HDBaseT Signal Level
• Reset Lamp Hours
• You can select the following settings only using a Web
browser.
• Monitor Password (up to 16 alphanumeric characters)
• IPv6 Settings (manual)
• HTTP port (port number used for Web Control except for
80 [default], 843, 3620, 3621, 3625, 3629, 4352, 4649, 5357,
10000, 10001, 41794)
g Related Links
• "Registering Digital Certificates from a Web Browser" p.124
• "Projector Setup Settings - ECO Menu" p.159
• "Network Menu - Basic Menu" p.152
Registering Digital Certificates from a Web Browser
You can register the digital certificates on the projector to provide security for
your presentation files (EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG).
a
124
You can also register the digital certificates in the projector's Network
menu. However, be sure to register just once or the certificate may not
install correctly.
s Network > Network Configuration > Wireless LAN > EAP
Method > Client Certificate
s Network > Network Configuration > Wireless LAN > EAP
Method > CA certificate
s Network > Network Configuration > Others > Web Server
Certificate
sure your digital certificate file is compatible with projector
a Make
registration.
b Make sure the projector is turned on.
your Web browser on a computer or device connected to the
c Start
network.
to the Epson Web Control screen by entering the projector's IP
d Go
address into the browser's address box.
You see the Epson Web Control screen.
Controlling a Networked Projector Using a Web Browser
125
g Click the Browse button, select the certificate file, and click Open.
h Enter a password in the Password box.
you finish registering the certificate, click Apply to finalize your
i When
changes and complete the registration.
e Select Advanced.
a
• You may need to log in before you see the Advanced screen. If
a login screen is displayed, enter your user name and
password. (The user name is EPSONWEB and the default
password is admin.)
• You can change the password in Web Control Password from
the projector's Network menu.
s Network > Network Configuration > Basic > Web
Control Password
f Under Network, select Manage Certificates.
Setting Up Projector Network E-Mail Alerts
You can set up the projector to send you an e-mail alert over the network if
there is a problem with the projector.
If you set the Standby Mode setting to Communication On in the projector's
ECO menu, you can receive the e-mail alerts even if the projector is in
standby mode (when the power is off).
a Press the [Menu] button on the control panel or remote control.
b Select the Network menu and press [Enter].
c Select Network Configuration and press [Enter].
d Select the Notifications menu and press [Enter].
126
a number for the SMTP server Port Number, from 1 to 65535
g Select
(default is 25).
an address field, enter the e-mail address, and select the alerts
h Choose
you want to receive. Repeat for up to three addresses.
a
Your e-mail address can be up to 32 alphanumeric characters
long.
you finish selecting settings, select Complete and follow the oni When
screen instructions to save your settings and exit the menus.
a
If a critical problem causes a projector to shut down, you may not
receive an e-mail alert.
g Related Links
• "Network Projector E-mail Alert Messages" p.126
• "Projector Setup Settings - ECO Menu" p.159
Network Projector E-mail Alert Messages
When a problem occurs with a projector on the network, and you selected to
receive e-mail alerts, you receive an e-mail containing the following
information:
e Set the Mail Notification setting to On.
f Enter the IP address for the SMTP Server option.
a
Do not use these addresses: 127.x.x.x or 224.0.0.0 through
255.255.255.255 (where x is a number from 0 to 255).
•
•
•
•
•
The email address set in From as the mail sender
Epson Projector in the subject line
The name of the projector experiencing a problem
The IP address of the affected projector
Detailed information about the problem
Setting Up Monitoring Using SNMP
Network administrators can install SNMP (Simple Network Management
Protocol) software on network computers so they can monitor projectors. If
your network uses this software, you can set up the projector for SNMP
monitoring.
a Press the [Menu] button on the control panel or remote control.
b Select the Network menu and press [Enter].
c Select Network Configuration and press [Enter].
d Select the Notifications menu and press [Enter].
e Set the SNMP setting to On.
up to two IP addresses to receive SNMP notifications, using 0 to
f Enter
255 for each address field.
a
Do not use these addresses: 127.x.x.x or 224.0.0.0 through
255.255.255.255 (where x is a number from 0 to 255). This
projector supports SNMP agent version 1 (SNMPv1).
127
the SNMP Community Name up to 32 alphanumeric characters
g Enter
long.
you have finished selecting settings, select Complete and follow
h When
the on-screen instructions to save your settings and exit the menus.
Using ESC/VP21 Commands
128
You can control the projector from an external device using ESC/VP21.
Item
g Related Links
• "ESC/VP21 Command List" p.128
• "Cable Layouts" p.129
Signal selection
Command
Computer1
Computer2
ESC/VP21 Command List
When the power ON command is transmitted to the projector, the power
turns on and it enters warm-up mode. When the projector's power has turned
on, a colon ":" (3Ah) is returned.
Auto
SOURCE 1F
RGB
SOURCE 11
Component
SOURCE 14
Auto
SOURCE 2F
RGB
SOURCE 21
Component
SOURCE 24
HDMI1/MHL
SOURCE 30
HDMI2
SOURCE A0
When a command is input, the projector executes the command and returns a
":", and then accepts the next command.
Video
SOURCE 41
USB Display
SOURCE 51
If the command being processed terminates abnormally, an error message is
output and a ":" is returned.
USB
SOURCE 52
The following commands are available.
LAN
SOURCE 53
Screen Mirroring *
SOURCE 56
HDBaseT **
SOURCE 80
On
MUTE ON
Off
MUTE OFF
Item
Power On/Off
Command
On
PWR ON
Off
PWR OFF
A/V Mute On/Off
* Screen Mirroring is available only with the EB-2265U/EB-2255U/EB2165W.
** HDBaseT is available only with the EB-2265U/EB-2165W.
Add a Carriage Return (CR) code (0Dh) to the end of each command and
transmit.
Contact Epson for more details.
Using ESC/VP21 Commands
• Flow control: None
Cable Layouts
Serial connection
• Connector shape: D-Sub 9-pin (male)
• Projector input port name: RS-232C
• Cable type: Crossover (null modem) cable
In the following illustration, the projector side is shown on the left, and the
computer side on the right:
Signal name
Function
GND
Signal wire ground
TD
Transmit data
RD
Receive data
Communications protocol
•
•
•
•
Default baud rate setting: 9600 bps
Data length: 8 bit
Parity: None
Stop-bit: 1 bit
129
PJLink Support
130
PJLink was established by the JBMIA (Japan Business Machine and
Information System Industries Association) as a standard protocol for
controlling network-compatible projector's as part of their efforts to
standardize projector control protocols.
The projector complies with the PJLink Class2 standard established by the
JBMIA.
The port number used for the PJLink search function is 4352 (UDP).
You need to make network settings before you can use PJLink.
It complies with all commands except for the following commands defined by
PJLink Class2, and agreement was confirmed by the PJLink standard
adaptability verification.
http://pjlink.jbmia.or.jp/english/
• Non-compatible commands
Function
Mute settings
PJLink command
Image muting set
AVMT 11
Audio muting set
AVMT 21
• Input ports and corresponding input source number
Input port name
Input source number
Computer1
11
Computer2
12
Video
21
HDMI1/MHL
32
HDMI2
33
USB
41
LAN
52
USB Display
53
HDBaseT *
56
Screen Mirroring **
57
* HDBaseT is available only with the EB-2265U/EB-2165W.
** Screen Mirroring is available only with the EB-2265U/EB-2255U/EB2165W.
• Manufacturer name displayed for "Manufacture name information query"
EPSON
• Model name displayed for "Product name information query"
•
•
•
•
•
•
•
•
•
•
EPSON 2265U
EPSON 2255U
EPSON 2250U
EPSON 2245U
EPSON 2165W
EPSON 2155W
EPSON 2140W
EPSON 2065/X550KG
EPSON 2055/X500KG
EPSON 2040
g Related Links
• "Using the Projector on a Network" p.99
Crestron RoomView Support
If you are using the Crestron RoomView network monitoring and control
system, you can set up your projector for use on the system. Crestron
RoomView lets you control and monitor your projector using a Web browser.
a
• You cannot use the Epson Web Control feature or the Message
Broadcasting plug-in for EasyMP Monitor when you use Crestron
RoomView.
• If you set the Standby Mode setting to Communication On in the
projector's ECO menu, you can control the projector even if the
projector is in standby mode (when the power is off).
131
b Select the Network menu and press [Enter].
c Select Network Configuration and press [Enter].
d Select the Others menu and press [Enter].
For additional information on Crestron RoomView, visit the Crestron Web
site.
http://www.crestron.com
To monitor devices in the system, you can use Crestron RoomView Express
or Crestron RoomView Server Edition provided by Creston. You can
communicate with the help desk and send emergency messages. See the
following Web site for details.
http://www.crestron.com/getroomview
This manual describes how to perform operations on your computer using a
Web browser.
g Related Links
• "Setting Up Crestron RoomView Support" p.131
• "Controlling a Networked Projector Using Crestron RoomView" p.131
• "Projector Setup Settings - ECO Menu" p.159
Setting Up Crestron RoomView Support
To set up your projector for monitoring and control using a Crestron
RoomView system, make sure your computer and projector are connected to
the network. If you are connecting wirelessly, set up the projector using the
Advanced network connection mode.
a Press the [Menu] button on the control panel or remote control.
the Crestron RoomView setting to On to allow the projector to be
e Set
detected.
you have finished selecting settings, select Complete and follow
f When
the on-screen instructions to save your settings and exit the menus.
g Turn off the projector, and then turn it on again to enable the setting.
Controlling a Networked Projector Using Crestron
RoomView
Once you have set up your projector to use Crestron RoomView, you can
control and monitor projection using a compatible Web browser.
a Start your Web browser on a computer connected to the network.
Crestron RoomView Support
the projector's IP address into the browser's address box and press
b Type
the computer's Enter key.
You see this screen:
132
g Related Links
• "Crestron RoomView Operation Window" p.132
• "Crestron RoomView Tools Window" p.133
Crestron RoomView Operation Window
Settings on the operation window let you control the projector and adjust the
projection image.
the input source that you want to control in the Sources List box.
c Select
You can scroll through available sources using the up and down arrows
in the box.
control projection remotely, click the on-screen buttons that
d Tocorrespond
to the projector's remote control buttons. You can scroll
A
through button options at the bottom of the screen.
a
These on-screen buttons do not directly correspond to the
projector's remote control buttons:
• OK acts as the [Enter] button
• Menu displays the projector's menu
e To view information about the projector, click the Info tab.
the projector, Crestron, and password settings, click the
f ToToolschange
tab, select settings on the displayed screen, and then click Send.
g When you finish selecting settings, click Exit to exit the program.
B
Power
Turns the projector on or off.
Vol-/Vol+
Adjusts the volume.
A/V Mute
Turns the video and audio on or off.
Switches to the image from the selected input source. To display input sources
that are not shown in Sources List, click (a) or (b) to scroll up or down. The
current video signal input source is displayed in blue.
You can change the source name if necessary.
Crestron RoomView Support
C
D
E
Freeze
Images are paused or released.
Contrast
Adjusts the difference between light and shade in the
images.
Brightness
Adjusts the image brightness.
Color
Adjusts the color saturation for the images.
Sharpness
Adjusts the image sharpness.
Zoom
Enlarges or reduces the image without changing the
projection size. Click the arrow buttons to change the
position of an enlarged image.
Arrow buttons
Performs the same operations as the arrow buttons on
the remote control.
OK
Performs the same operation as [Enter] on the remote
control.
Menu
Displays and closes the projector's menu.
Auto
Optimizes Tracking, Sync., and Position in the
projector's Signal menu while projecting an analog
RGB signal from Computer1 or Computer2 port.
133
Crestron RoomView Tools Window
Settings on the Tools window let you customize various projector setup
features.
A
Make settings for Crestron central controllers.
B
Projector Name
Enter a name to differentiate the projector that is
currently connected from other projectors on the
network. (up to 16 alphanumeric characters)
Search
Changes to the next input source that is sending an
image.
Esc
Performs the same operation as the [Esc] button on the
remote control.
Location
Contact IT Help
Displays the Help Desk window. Used to send
messages to, and receive messages from, the
administrator using Crestron RoomView Express.
Enter an installation location name for the projector
that is currently connected on the network. (up to 32
alphanumeric characters and symbols)
Assigned To
Enter a user name for the projector. (up to 32
alphanumeric characters and symbols)
Info
Displays information on the projector that is currently
connected.
DHCP
Select to use DHCP. You cannot enter an IP address if
DHCP is enabled.
Tools
Changes settings in the projector that is currently
connected.
IP Address
Enter the IP address to assign to the currently
connected projector.
Subnet Mask
Enter a subnet mask for the currently connected
projector.
Default Gateway
Enter the gateway address for the currently connected
projector.
Send
Click to confirm the changes made to the Projector.
Crestron RoomView Support
C
D
Enabled (Admin
Password)
Select to require a password to open the Tools window.
New Password
Enter the new password when changing the password
to open the Tools window. (up to 26 alphanumeric
characters)
Confirm
Enter the same password as you entered in New
Password. If the passwords are not the same, an error
is displayed.
Send
Click to confirm the changes made to the Admin
Password.
Enabled (User
Password)
Select to require a password to open the operation
window on the computer.
New Password
Enter the new password when changing the password
to open the operation window. (up to 26 alphanumeric
characters)
Confirm
Enter the same password as you entered in New
Password. If the passwords are not the same, an error
is displayed.
Send
Click to confirm the changes made to the User
Password.
134
Setting Projector Event Schedules
You can schedule up to 30 events to occur automatically on your projector,
such as turning the projector on or off or switching the input source (EB2265U/EB-2255U/EB-2250U/EB-2245U/EB-2165W/EB-2155W/EB-2065/EB2055/EB-X550KG/EB-X500KG). The projector performs the selected events
on the specified date and time in the schedule you set up.
135
f Select Add New and press [Enter].
Warning
Do not place flammable objects in front of the lens. If you schedule the projector
to turn on automatically, flammable objects in front of the lens could catch on a
fire.
a
If you set a Schedule Protection password, turn off your Schedule
Protection password first.
date and time in the Date & Time menu.
a Set the
Extended > Operation > Date & Time
s
b Press the [Menu] button on the control panel or remote control.
c Select the Extended menu and press [Enter].
d Select Schedule Settings and press [Enter].
e Select Schedule and press [Enter].
g Select the event details you want to perform.
Setting Projector Event Schedules
136
h Select the date and time at which you want the event to occur.
The scheduled events are displayed on the screen with icons indicating
the event status.
i Select Save and press [Enter].
A
: valid schedule
: regular schedule
: invalid schedule
B The date currently selected (highlighted in yellow)
C
: one time schedule
: regular schedule
: standby schedule (turns communication on or off during standby)
: invalid schedule
j To edit a scheduled event, select the schedule and press [Esc].
an option from the menu displayed.
k Select
• On or Off lets you enable or disable the selected event.
Setting Projector Event Schedules
• Edit lets you change the event details or date and time.
• Clear lets you remove the scheduled event from a list.
l Select Complete, then select Yes.
To delete all scheduled events, select Schedule Reset.
g Related Links
• "Setting the Date and Time" p.41
• "Setting a Password" p.94
137
Adjusting the Menu Settings
Follow the instructions in these sections to access the projector menu system and change projector settings.
g Related Links
• "Using the Projector's Menus" p.139
• "Using the On-screen Keyboard" p.140
• "Image Quality Settings - Image Menu" p.141
• "Input Signal Settings - Signal Menu" p.143
• "Projector Feature Settings - Settings Menu" p.145
• "Projector Setup Settings - Extended Menu" p.147
• "Projector Network Settings - Network Menu" p.150
• "Projector Setup Settings - ECO Menu" p.159
• "Projector Information Display - Info Menu" p.161
• "Projector Reset Options - Reset Menu" p.164
• "Copying Menu Settings Between Projectors (Batch Setup)" p.165
Using the Projector's Menus
You can use the projector's menus to adjust the settings that control how your
projector works. The projector displays the menus on the screen.
a Press the [Menu] button on the control panel or remote control.
You see the menu screen displaying the Image menu settings.
the up or down arrow buttons to move through the menus listed
b Press
on the left. The settings for each menu are displayed on the right.
a
The available settings depend on the current input source.
c To change settings in the displayed menu, press [Enter].
139
d Press the up or down arrow button to move through the settings.
the settings using the buttons listed on the bottom of the menu
e Change
screens.
f To return all the menu settings to their default values, select Reset.
g When you finish changing settings on a menu, press [Esc].
h Press [Menu] or [Esc] to exit the menus.
Using the On-screen Keyboard
The on-screen keyboard is displayed when you need to enter numbers and
characters.
a
Use the arrow buttons on the control panel or remote control to
highlight the number or character you want to enter and press the
[Enter] button.
a
Each time you select the CAPS key, the characters change
between upper case and lower case. Each time you select the
SYM1/2 key, the symbols enclosed by the frame change.
entering the text, select Finish on the keyboard to confirm your
b After
entries. Select Cancel to cancel entering text.
a
You can select projector settings and control projection over a network
using a Web browser from your computer.
Some symbols cannot be entered using the on-screen keyboard. Use
your Web browser to enter the text.
g Related Links
• "Available Text Using the On-screen Keyboard" p.140
• "Controlling a Networked Projector Using a Web Browser" p.122
140
Available Text Using the On-screen Keyboard
You can enter the following text when using the on-screen keyboard.
Text type
Details
Numbers
0123456789
Alphabet
ABCDEFGHIJKLMNOPQRSTUVWXY
Z
abcdefghijklmnopqrstuvwxyz
Symbols
!"#$%&'()*+,-./:;<=>?@[\]
^_`{|}~
Image Quality Settings - Image Menu
Settings on the Image menu let you adjust the quality of your image for the
input source you are currently using. The available settings depend on the
currently selected input source.
141
Setting
Options
Color Temp.
Image
Enhancement
Sets the color tone based on color
temperature. The image is tinted blue
when a high value is selected and tinted
red when a low value is selected.
Color Temp.
Color Temp.: sets the color temperature
according to the color mode you selected.
Customized
Customized: adjusts the individual R
(red), G (green), and B (blue)
components of the offset and gain.
Noise Reduction
Reduces flickering in analog images.
Advanced
Options
Description
Color Mode
See the list of
available color
modes
Adjusts the vividness of image colors for
various image types and environments.
Brightness
Varying levels
available
Lightens or darkens the overall image.
Contrast
Varying levels
available
Adjusts the difference between light and
dark areas of the image.
Color Saturation
Varying levels
available
Adjusts the intensity of the image colors.
Tint
Varying levels
available
Adjusts the balance of green to magenta
tones in the image.
Sharpness
Varying levels
available
Adjusts the sharpness or softness of
image details.
Selects the various detailed color settings:
Gamma
Gamma: adjusts the coloring by selecting
one of the gamma correction values, or
referring to the projected image or a
gamma graph.
RGBCMY
RGBCMY: adjusts the hue, saturation,
and brightness of each color R (red), G
(green), B (blue), C (cyan), M (magenta),
Y (yellow) individually.
Deinterlacing
(For interlaced
signal
[480i/576i/1080i]
input)
Deinterlacing: sets whether or not to
convert interlaced-to-progressive signals
for certain video image types.
• Off: for fast-moving video images.
• Video: for most video images.
• Film/Auto: for movies, computer
graphics, and animation.
Auto Iris
Off
Normal
High Speed
Adjusts the projected luminance based
on the image brightness.
Available when the Color Mode is set to
Dynamic or Cinema.
Reset
—
Resets all adjustment values on the
Image menu for the selected color mode
to their default settings.
To change settings for an input source, make sure the source is connected and
select that source.
Setting
Description
Image Quality Settings - Image Menu
a
• The Brightness setting does not affect lamp brightness. To change
the lamp brightness mode, use the Power Consumption setting in
the projector's ECO menu.
• You cannot select the Noise Reduction setting when the following
are being input.
• The Deinterlacing setting is set to Off.
• A digital RGB signal is being input.
• An interlaced signal (480i/576i/1080i) is being input.
g Related Links
• "Available Color Modes" p.60
142
Input Signal Settings - Signal Menu
Normally the projector automatically detects and optimizes the input signal
settings. If you need to customize the settings, you can use the Signal menu.
The available settings depend on the currently selected input source.
a
a
You cannot select settings on the Signal menu when the current input
source is one of the following:
• USB Display
• USB
• LAN
• Screen Mirroring (EB-2265U/EB-2255U/EB-2165W)
143
Setting
Options
Description
Aspect
See the list of
available aspect
ratios.
Sets the aspect ratio (width-to-height
ratio) for the selected input source.
Tracking
Varying levels
available
Adjusts the signal to eliminate vertical
stripes in computer images.
Sync.
Varying levels
available
Adjusts the signal to eliminate fuzziness
or flickering in computer images.
Position
—
Adjusts the image location on the screen.
Auto Setup
On
Off
Automatically optimizes computer image
quality (when On).
Overscan
Auto
Off
4%
8%
Changes the projected image ratio to
make the edges visible by a selectable
percentage or automatically.
Advanced
HDMI Video
Range
HDMI Video Range: sets the video
range to match the setting of the device
connected to the HDMI and HDBaseT
port.
• Auto: detects the video range
automatically.
• Normal: normally for images from a
device other than a computer; can also
be selected if the black areas of the
image are too bright.
• Expanded: normally for images from a
computer; can also be selected if the
image is too dark.
Input Signal
Input Signal: specifies the signal type
from the input sources connected to the
computer ports.
• Auto: detects signals automatically.
• RGB: corrects color for computer/RGB
video inputs.
• Component: corrects color for
component video inputs.
You can restore the default settings of the Tracking, Sync., and
Position settings by pressing the [Auto] button on the remote control.
To change settings for an input source, make sure the source is connected and
select that source.
Setting
Options
Description
Resolution
Auto
Wide
Normal
Sets the input signal resolution if not
detected automatically using the Auto
option.
Input Signal Settings - Signal Menu
Setting
Reset
Options
Description
Video Signal
Video Signal: specifies the signal type
from the input sources connected to the
video ports. If interference appears or no
image appears when set to Auto, select
the appropriate signal according to the
connected equipment.
—
Resets all adjustment values on the
Signal menu to their default settings,
except for the following:
• Input Signal
g Related Links
• "Available Image Aspect Ratios" p.58
144
Projector Feature Settings - Settings Menu
Options on the Settings menu let you customize various projector features.
145
Setting
Options
Gesture Presenter *
Volume
Adjusts the Gesture Presenter options:
Start/Stop
Start/Stop: starts or stops the Gesture
Presenter feature.
Marker Position
Marker Position: sets the marker
position to the right or left.
Gesture Presenter
Gesture Presenter: enables or disables
the Gesture Presenter feature.
Varying levels
available
Adjusts the volume of projector’s speaker
system.
You can also adjust the volume of
external speakers.
Setting values are saved for each source.
HDMI Link
Setting
Adjusts the HDMI Link options:
Device
Connections
Device Connections: lists the devices
connected to the HDMI ports.
Adjusts image shape to rectangular
(horizontally and vertically).
HDMI Link
HDMI Link: enables or disables the
HDMI Link features.
H/V-Keystone
H/V-Keystone: select to manually
correct horizontal and vertical sides, or
turn automatic correction on or off.
You can also turn H-Keystone Adjuster
on or off (EB-2140W/EB-2040).
Power On Link
Quick Corner
Quick Corner: select to correct image
shape and alignment using an on-screen
display.
Screen Size
Source
Swap Screens
Audio Source
Align
Display the QR
Code
Exit Split Screen
Divides the viewing area horizontally and
displays two images side-by-side (press
[Esc] to cancel split screen display).
Power On Link: controls what happens
when you turn on the projector or
connected device.
• Bidirectional: automatically turns on
the connected device when you turn on
the projector, and vice versa.
• Device -> PJ: automatically turns on
the projector when you turn on the
connected device.
• PJ -> Device: automatically turns on
the connected device when you turn on
the projector.
Power Off Link
Power Off Link: controls whether
connected devices are turned off when
you turn off the projector.
Options
Keystone
Split Screen
Description
Description
Projector Feature Settings - Settings Menu
Setting
Lock Setting
Options
Description
Setting
Options
Description
Link Buffer
Link Buffer: improves the performance
of the linked operations by changing the
settings if the HDMI Link function is not
working correctly.
Test Pattern
—
Displays a test pattern to assist in
focusing and zooming the image and
correcting image shape (press the [Esc]
button to cancel pattern display).
Control Panel Lock Controls projector button locking to
secure the projector:
Full Lock: locks all buttons.
Partial Lock: locks all buttons except the
power button.
Off: no buttons locked.
Pointer Shape
Pointer 1:
Changes the shape of the remote control
pointer.
Pointer 2:
Pointer 3:
Remote Receiver
User Button
146
Front/Rear
Front
Rear
Off
Limits reception of remote control
signals by the selected receiver; Off turns
off all receivers.
Power
Consumption
Info
Deinterlacing
Test Pattern
Resolution
Multi-Projection
Display the QR
Code
Assigns a menu option to the [User]
button on the remote control for onetouch access.
Attention
If a pattern is displayed for a
long time, a residual image may
be visible in projected images.
Reset
—
Resets all adjustment values on the
Settings menu to their default settings,
except for the following:
• Power On Link
• Power Off Link
• Link Buffer
• User Button
* Available only for EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG.
Projector Setup Settings - Extended Menu
Settings on the Extended menu let you customize various projector setup
features.
147
Setting
Options
Description
Display
Background
Display Background: sets the screen
color or logo to display when no signal is
received.
Startup Screen
Startup Screen: set to On to display a
logo when the projector starts up.
A/V Mute
A/V Mute: sets the screen color or logo
to display when A/V Mute is turned on.
User's Logo
—
Creates a screen that the projector
displays to identify itself and enhance
security.
Projection
Front
Front/Ceiling
Rear
Rear/Ceiling
Selects the way the projector faces the
screen so the image is oriented correctly.
Operation
Setting
Options
Home Screen
Description
Selects the projector's Home screen
display options:
Home Screen Auto Home Screen Auto Disp.: select whether
Disp.
or not to display the Home screen
automatically when there is no input
signal when turning on the projector.
Custom Function 1 Custom Function 1/Custom Function
Custom Function 2 2: select to set functions and the display
as the customized Home screen.
Display
Selects various display options:
Messages
Messages: set to On to display messages
such as input source name, color mode
name, aspect ratio, no signal message, or
high temperature warning on your
projected image. Set to Off if you do not
want to display messages.
Selects various operation options:
Direct Power On
Direct Power On: lets you turn on the
projector by plugging it in without
pressing the power button.
High Altitude
Mode
High Altitude Mode: regulates the
projector’s operating temperature at
altitudes above 1500 m.
Auto Source Search Auto Source Search: set to On to detect
the input signal automatically and
project images when there is no input
signal.
Auto Power On
Auto Power On: select the image source
from which you want to automatically
start projection. When the projector
detects the input signal from the selected
image source, it projects automatically in
standby mode.
(HDMI1/Computer1/USB Display)
Projector Setup Settings - Extended Menu
Setting
Options
Description
Monitor Out Port
Monitor Out Port: changes the input
and output for the Computer2/Monitor
Out ports. When outputting images to an
external monitor, select Monitor Out.
When inputting image signals from a
computer or component video signals
from other video sources, select
Computer2.
Date & Time *
A/V Settings
Date & Time: adjusts the projector's
system time and date settings.
• Daylight Saving Time: set to On to
activate daylight saving time.
• Internet Time: set to On to update the
time automatically through an Internet
time server.
148
Setting
Options
Description
Extron XTP
Extron XTP: set to On when you
connect an Extron XTP transmitter or
switcher to the HDBaseT ports. See the
following Extron Web site for more
details on the XTP system.
http://www.extron.com/
Multi-Projection
Make settings when projecting from
multiple projectors:
Multi-Projection
Multi-Projection: set to On to match the
display quality of multiple projectors.
When set to On, the following are
automatically set to prevent unevenness
on the right and left screens.
s Image > Auto Iris > Off
s ECO > Power Consumption >
Normal
s ECO > Light Optimizer > Off
Selects various audio and video output
settings:
A/V Output
A/V Output: set to Always On to output
audio and images to external devices
when the projector is in standby mode.
Projector ID
Audio Output
Audio Output: selects the audio input
port when projecting images from
anything except for HDMI ports.
Projector ID: assigns an ID for the
projector when you use multiple
projectors.
Color Mode
HDMI1 Audio
Output
HDMI2 Audio
Output
HDMI1 Audio Output/HDMI2 Audio
Output: selects the audio input port
when projecting images from HDMI
ports.
Color Mode: adjusts the vividness of
image colors for various image types and
environments. When using multiple
projectors, make sure you select the same
color mode for all of the projectors.
Color Matching
Selects the communication settings for
connections to an HDBaseT transmitter
or switcher.
Color Matching: corrects the difference
between the tint and brightness of each
projected image.
RGBCMY
Control Communications: enables or
disables communication from the
Ethernet and serial ports on the
transmitter; turning on this setting
disables the projector's LAN and RS232C ports. (Set Extron XTP to Off first.)
RGBCMY: adjusts the Hue, Saturation,
and Brightness for R (Red), G (Green), B
(Blue), C (Cyan), M (Magenta), and Y
(Yellow) color components.
Reset
Reset: resets all adjustment values for the
Multi-Projection menu to their default
settings.
HDBaseT **
Control
Communications
Projector Setup Settings - Extended Menu
Setting
Options
Description
Schedule Settings *
To Schedule
Settings menu
Schedules projector events to occur
automatically at selected dates and times.
Language
Various languages
available
Select the language for projector menu
and message displays.
Reset
—
Resets all adjustment values on the
Extended menu to their default settings,
except for the following:
• User's Logo
• Projection
• High Altitude Mode
• Auto Source Search
• Monitor Out Port
• Date & Time *
• A/V Output
• HDBaseT **
• Multi-Projection
• Projector ID
• Color Mode
• Color Matching
• Schedule Settings *
• Language
* Available only for EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG.
** Available only for EB-2265U/EB-2165W.
a
When you set User's Logo Protection to On in the Password
Protection screen, you cannot change settings related to user's logo
display (Display Background, Startup Screen, A/V Mute in the
Display setting). Set User's Logo Protection to Off first.
g Related Links
• "Selecting Password Security Types" p.95
149
Projector Network Settings - Network Menu
Settings on the Network menu let you view network information and set up
the projector for controlling over a network.
When you set Network Protection to On in the Password Protection screen,
you cannot change the network settings. Set Network Protection to Off first.
Setting
Options
Description
Screen Mirroring *
On
Off
Configures your Screen Mirroring
settings.
Select On to project with the Screen
Mirroring features.
Screen Mirroring
Info *
Display Name
MAC Address
Region Code
Channel
Connected Device
Displays Screen Mirroring status and
details.
Available when you have set Screen
Mirroring to On.
Screen Mirroring
Settings *
To Screen
Mirroring Settings
menu
Configures your Screen Mirroring
settings.
150
Setting
Options
Description
Wireless LAN
Power
On
Off
Configures your wireless LAN settings.
Select On to project images via a wireless
LAN. If you do not want to connect via
wireless LAN, turn it off to prevent
unauthorized access by others.
Net. Info. Wireless LAN
Connection Mode
Wireless LAN Sys.
Antenna Level
Projector Name
SSID
DHCP
IP Address
Subnet Mask
Gateway Address
MAC Address
Region Code
IPv6
Displays wireless network status and
details.
Available when you have set Wireless
LAN Power to On.
The following settings are displayed
when you select the IPv6 option.
• IPv6 Address (Manual)
• IPv6 Address
• Prefix Length
• Gateway Address
• IPv6 Address (Auto)
•
•
•
•
Temporary Address
Link-local Address
Stateless Address
Stateful Address
Projector Network Settings - Network Menu
Setting
Options
Description
Net. Info. - Wired
LAN
Projector Name
DHCP
IP Address
Subnet Mask
Gateway Address
MAC Address
IPv6 Address
(Manual)
IPv6 Address
(Auto)
Displays wired network status and
details.
The following settings are displayed
when you select the IPv6 Address
(Manual) or IPv6 Address (Auto)
option.
• IPv6 Address (Manual)
• IPv6 Address
• Prefix Length
• Gateway Address
• IPv6 Address (Auto)
•
•
•
•
• "Selecting Password Security Types" p.95
Network Menu - Screen Mirroring Settings
Settings on the Screen Mirroring Settings menu let you select the Screen
Mirroring settings (EB-2265U/EB-2255U/EB-2165W).
s Network > Screen Mirroring Settings
Temporary Address
Link-local Address
Stateless Address
Stateful Address
Display the QR
Code
—
Displays a QR code for connecting with
iOS or Android devices using the Epson
iProjection app.
Network
Configuration
To additional
network menus
Configures your network settings.
* Available only for EB-2265U/EB-2255U/EB-2165W.
a
151
Once you have connected your projector to your network, you can
select projector settings and control projection using a compatible Web
browser. This allows you to access the projector remotely.
g Related Links
• "Network Menu - Screen Mirroring Settings" p.151
• "Network Menu - Basic Menu" p.152
• "Network Menu - Wireless LAN Menu" p.153
• "Network Menu - Wired LAN Menu" p.155
• "Network Menu - Notifications Menu" p.156
• "Network Menu - Others Menu" p.157
• "Network Menu - Reset Menu" p.158
Setting
Options
Description
Display Name
Up to 32
alphanumeric
characters
Enter a name to identify the projector
when searching for the projector using
the screen mirroring feature.
Operation Mode
Basic
Extended
Select Extended to connect with
advanced options.
Basic
Wireless LAN Sys.
Sets the communication method between
the projector and the mobile device.
Adjust Image
Quality
Adjusts the screen mirroring
speed/quality.
When you want to increase image
quality, select a small number. When you
want to increase processing speed, select
a large number.
Projector Network Settings - Network Menu
Setting
Options
Description
Connection Mode
Selects the type of WPS (Wi-Fi Protected
Setup) when you connect to the network
wirelessly. Select PIN to improve the
connection security. If your mobile
device supports only the PBC
connection, select PIN/PBC.
Available when you have set Operation
Mode to Basic.
Extended
Display
Reset
152
s Network > Network Configuration > Basic
Available when you have set Operation
Mode to Extended.
Meeting Mode
Selects the type of meeting.
• Interruptions OK: lets you connect to
another mobile device during Screen
Mirroring projection.
• No Interruptions: lets you exclusively
connect to one device.
Channel
Selects the wireless channel used by
Screen Mirroring.
Display PIN Code
Set to On to display the eight-digit PIN
code on the projected image when
projecting input sources other than
Screen Mirroring.
Display Device
Name
Set to On to display the newly connected
device name on the projected image
when projecting input sources other than
Screen Mirroring.
—
Resets all adjustment values on the
Screen Mirroring Settings menu to their
default settings.
Network Menu - Basic Menu
Settings on the Basic menu let you select the basic network settings.
Setting
Options
Description
Projector Name
Up to 16
alphanumeric
characters
(do not use " * + ,
/:;<=>?[\]`|
spaces)
Enter a name to identify the projector
over the network.
PJLink Password
Up to 32
alphanumeric
characters
Enter a password for using the PJLink
protocol for projector control.
Remote Password
Up to 8
alphanumeric
characters
(do not use * :
spaces)
Enter a password for accessing the
projector using the Basic Control. (User
name is EPSONREMOTE; default
password is guest.)
Web Control
Password
Up to 8
alphanumeric
characters
(do not use * :
spaces)
Enter a password for accessing the
projector over the Web. (User name is
EPSONWEB; default password is
admin.)
Projector Network Settings - Network Menu
Setting
Options
Description
Moderator
Password
Four-digit number
Enter a password for accessing the
projector as a moderator using EasyMP
Multi PC Projection or Epson
iProjection. (No password is set by
default.)
Projector Keyword
On
Off
Set to On to enable a security password
to prevent access to the projector by
anyone not in the same room as the
projector. You must enter the random
keyword displayed from a computer
using EasyMP Multi PC Projection or
Epson iProjection to access the projector
and share the current screen.
Display LAN Info.
Text & QR Code
Text
Set the display format for the projector's
network information.
By simply reading the QR code with
Epson iProjection, you can connect to
the network. The default value is Text &
QR Code.
153
s Network > Network Configuration > Wireless LAN
Setting
Options
Connection Mode
Description
Select the type of wireless connection:
Quick
Quick: lets you connect to multiple
smartphones, tablets, or computers
directly using wireless communication.
When you select Quick connection
mode, the projector acts as an easy access
point. (We recommend limiting the
number of devices to six or less to
maintain the projection performance.)
Advanced
Advanced: lets you connect to multiple
smartphones, tablets, or computers over
a wireless network access point.
Network Menu - Wireless LAN Menu
Settings on the Wireless LAN menu let you select the wireless LAN settings.
Search Access Point To Search View
Search for available wireless network
access points in Advanced connection
mode. Depending on the access point
settings, they may not be displayed in the
list.
SSID
Sets the SSID (network name) of the
wireless LAN system the projector is
connecting to.
Up to 32
alphanumeric
characters
Projector Network Settings - Network Menu
Setting
Options
Security
Description
Options
Description
EAP Type
EAP Type: selects the protocol for
authentication.
• PEAP: authentication protocol widely
used in Windows Server.
• PEAP-TLS: authentication protocol
used in Windows Server. Select this
when using a client certificate.
• EAP-TLS: authentication protocol
widely used to use a client certificate.
• EAP-FAST, LEAP: select this when
these authentication protocols are
used.
User name
User name: enter up to 64 alphanumeric
characters. You can enter up to 32
alphanumeric characters in the projector
menu (you cannot use : and spaces). To
enter more than 32 characters, use your
Web browser. You can enter a domain
name by adding it before the user name
and separating them with a backslash
(domain\username).
When importing a client certificate, the
name the certificate was issued to is
automatically set.
For WPA2-PSK and WPA/WPA2-PSK
security, selects the pre-shared
passphrase used on the network.
When the passphrase is entered and the
[Enter] button is pressed, the value is set
and displayed as an asterisk (*).
We recommend changing the passphrase
periodically for security. If the network
settings are initialized, it returns to the
initial passphrase.
Password
Password: enter a password up to 64
alphanumeric characters for
authentication when using the PEAP,
EAP-FAST, or LEAP type. You can enter
up to 32 alphanumeric characters in the
projector menu (you cannot use * : and
spaces). To input more than 32
characters, use your Web browser. After
you enter the password and select Finish,
the password is displayed as an asterisk
(*).
Set the EAP settings for WPA2-EAP and
WPA/WPA2-EAP security.
Client Certificate
Client Certificate: imports the client
certificate when using the PEAP-TLS or
EAP-TLS type.
Selects the type of security used on the
wireless network.
When setting security, follow the
instructions from the administrator of
the network system you want to connect
to.
Open
Open: security is not set.
WPA2-PSK
WPA2-PSK: communication is
performed using WPA2 security. Uses
AES method for encryption. When
establishing a connection from a
computer to the projector, enter the
value set in the passphrase.
WPA/WPA2-PSK
WPA/WPA2-PSK: connects in WPA
personal mode. Encryption method is
selected automatically according to the
access point settings. Set a passphrase
which is the same for the access point.
WPA2-EAP *
WPA2-EAP or WPA/WPA2-EAP:
WPA/WPA2-EAP * connects in WPA enterprise mode.
Encryption method is selected
automatically according to the access
point settings. Select this item when
using LEAP.
Passphrase
EAP Method *
Various
passphrases from 8
to 32 characters
(when entering
from a Web
browser: various
passphrases from 8
to 63 characters)
154
Setting
Projector Network Settings - Network Menu
Setting
Channel
IP Settings
SSID Display
Options
Description
Verify Server Cert.
Verify Server Cert.: selects whether to
verify the server certificate when a CA
certificate has been set.
CA certificate
CA certificate: imports the CA certificate
when using the PEAP, PEAP-TLS, EAPTLS, or EAP-FAST type.
RADIUS
Serv.Name
RADIUS Serv.Name: enter the server
name to verify. You can enter up to 32
alphanumeric characters (you cannot use
* : and spaces).
1ch
6ch
11ch
In Quick connection mode, selects the
frequency band (channel) used by the
wireless LAN.
DHCP
IP Address
Subnet Mask
Gateway Address
DHCP: set to On if your network assigns
addresses automatically; set to Off to
manually enter the network's IP
Address, Subnet Mask, and Gateway
Address using 0 to 255 for each address
field.
Do not use these addresses: 0.0.0.0,
127.x.x.x, 192.0.2.x or 224.0.0.0 through
255.255.255.255 (where x is a number
from 0 to 255) for IP Address,
255.255.255.255 or 0.0.0.0 through
254.255.255.255 for Subnet Mask, and
0.0.0.0, 127.x.x.x or 224.0.0.0 through
255.255.255.255 for Gateway Address.
On
Off
Select whether to display the SSID on the
network standby screen and Home
screen.
IP Address Display On
Off
Select whether to display the IP address
on the network standby screen and
Home screen.
IPv6 Settings
Select the IPv6 settings if you want to
connect the projector to the network
using IPv6:
155
Setting
Options
Description
IPv6
IPv6: set to On if you want to connect
the projector to the network using IPv6.
IPv6 is supported to monitor and control
the projector over a network using Epson
Web Control and PJLink.
Auto Configuration Auto Configuration: set to On to assign
addresses automatically according to the
Router Advertisement.
Use Temporary
Address
Use Temporary Address: set to On if
you want to use a temporary IPv6
address.
* Available only for EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG.
Network Menu - Wired LAN Menu
Settings on the Wired LAN menu let you select the wired LAN settings.
s Network > Network Configuration > Wired LAN
Projector Network Settings - Network Menu
Setting
Options
Description
IP Settings
DHCP
IP Address
Subnet Mask
Gateway Address
DHCP: set to On if your network assigns
addresses automatically; set to Off to
manually enter the network's IP
Address, Subnet Mask, and Gateway
Address using 0 to 255 for each address
field.
Do not use these addresses: 0.0.0.0,
127.x.x.x, 192.0.2.x or 224.0.0.0 through
255.255.255.255 (where x is a number
from 0 to 255) for IP Address,
255.255.255.255 or 0.0.0.0 through
254.255.255.255 for Subnet Mask, and
0.0.0.0, 127.x.x.x or 224.0.0.0 through
255.255.255.255 for Gateway Address.
IP Address Display On
Off
Select whether to display the IP address
on the network standby screen.
IPv6 Settings
Select the IPv6 settings if you want to
connect the projector to the network
using IPv6:
IPv6
IPv6: set to On if you want to connect
the projector to the network using IPv6.
IPv6 is supported to monitor and control
the projector over a network using Epson
Web Control and PJLink.
156
s Network > Network Configuration > Notifications
Setting
Options
Description
Mail Notification
On
Off
Set to On to send an email to the preset
addresses when a problem or warning
occurs with a projector.
SMTP Server
IP address
Enter the IP address for the projector's
SMTP server using 0 to 255 for each
address field.
Do not use these addresses: 127.x.x.x,
192.0.2.x or 224.0.0.0 through
255.255.255.255 (where x is a number
from 0 to 255).
Port Number
1 to 65535 (default
is 25)
Select a number for the SMTP server
Port Number.
Auto Configuration Auto Configuration: set to On to assign
addresses automatically according to the
Router Advertisement.
Use Temporary
Address
Use Temporary Address: set to On if
you want to use a temporary IPv6
address.
Network Menu - Notifications Menu
Settings on the Notifications menu let you receive an email notification if a
problem or warning occurs in the projector.
Projector Network Settings - Network Menu
157
Setting
Options
Description
Setting
From
Up to 32
alphanumeric
characters
Up to 64
alphanumeric
characters from the
Web browser
(do not use " ( ) , : ;
< > [ \] spaces)
Enter the email address of the sender.
Notified IP Address IP address
On
Off
Set to On to monitor the projector using
SNMP. To monitor the projector, you
need to install the SNMP manager
program on your computer. SNMP
should be managed by a network
administrator.
The default value is Off.
Address 1 Setting
Address 2 Setting
Address 3 Setting
SNMP
Enter the e-mail address, and select the
alerts you want to receive. Repeat for up
to 3 addresses.
Trap IP Address 1
Trap IP Address 2
IP address
Enter up to two IP addresses to receive
SNMP notifications, using 0 to 255 for
each address field.
Do not use these addresses: 127.x.x.x or
224.0.0.0 through 255.255.255.255
(where x is a number from 0 to 255).
Community Name
Up to 32
alphanumeric
characters
(do not use spaces
and any symbols
other than @)
Set the SNMP community name.
PJLink Notification On
Off
Options
Description
Enter the IP address to receive the
projector's operating status when the
PJLink notification function is enabled.
Enter the addresses using 0 to 255 for
each address field.
Do not use these addresses: 127.x.x.x or
224.0.0.0 through 255.255.255.255
(where x is a number from 0 to 255).
Network Menu - Others Menu
Settings on the Others menu let you select other network settings.
s Network > Network Configuration > Others
Enables or disables the PJLink
notification function.
Setting
Options
Description
Secure HTTP *
On
Off
To strengthen security, communication
between the projector and computer in
Web control is encrypted. When setting
security with Web control, it is
recommended to set this to On.
Projector Network Settings - Network Menu
Setting
Options
Description
Web Server Cert. *
—
Imports the Web server certificate for
secure HTTP.
Priority Gateway
Wired LAN
Wireless LAN
You can set the priority gateway.
AMX Device
Discovery
On
Off
Set to On when you want to allow the
projector to be detected by AMX Device
Discovery.
Crestron
RoomView
On
Off
Set to On only when monitoring or
controlling the projector over the
network using Crestron RoomView.
Enabling Crestron RoomView disables
the Epson Message Broadcasting feature
in the EasyMP Monitor software.
Control4 SDDP
On
Off
Set to On to allow device information to
be acquired using Control4 Simple
Device Discovery Protocol (SDDP).
Message
Broadcasting
On
Off
Set to On to enable EPSON Message
Broadcasting feature.
You can download Message Broadcasting
and its Operation Guide from the
following Web site.
http://www.epson.com/
* Available only for EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG.
g Related Links
• "Crestron RoomView Support" p.131
Network Menu - Reset Menu
Settings on the Reset menu let you reset all of the network settings.
158
s Network > Network Configuration > Reset
Setting
Options
Description
Reset network
settings.
Yes
No
Select Yes to reset all network settings.
Projector Setup Settings - ECO Menu
Settings on the ECO menu let you customize projector functions to save
power.
Setting
Options
Description
Light Optimizer
On
Off
When set to On, the lamp brightness is
adjusted according to the projected
image. This helps to reduce the power
consumption by lowering the lamp
brightness according to the scene being
projected.
The setting is stored for each Color
Mode.
This item is enabled when:
• Power Consumption is set to Normal
or Auto.
• Auto Iris is set to Off.
s Image > Auto Iris
• Multi-Projection is set to Off.
s Extended > Multi-Projection >
Multi-Projection
Sleep Mode
On
Off
Automatically turns off the projector
after an interval of inactivity (when On).
Sleep Mode Timer
1 to 30 minutes
Sets the interval for Sleep Mode.
Description
Lens Cover Timer
Selects the brightness mode of the
projector lamp. You cannot select
settings when you use your projector at
high altitude or in locations subject to
high temperatures.
On
Off
Automatically turns off the projector
after 30 minutes if the lens cover is
closed (when On).
A/V Mute Timer
On
Off
Automatically turns off the projector
after 30 minutes if A/V Mute is enabled
(when On).
When you select a power-saving setting, a leaf icon appears next to the menu
item.
Setting
Options
Power
Consumption
159
Auto *
Auto: sets the projector to sense the
optimum lamp brightness needed and
adjusts the lamp's brightness accordingly.
Normal
Normal: sets maximum lamp brightness.
ECO
ECO: reduces lamp brightness and fan
noise, and saves power and lamp life.
Projector Setup Settings - ECO Menu
Setting
Options
Description
Standby Mode
Communication
On
Communication
Off
Communication On indicates that the
projector can be monitored over a
network when the projector is in standby
mode. Enable this setting to allow the
following operations to occur when the
projector is in standby mode:
• Monitor and control the projector over
a network
• Communication from the HDBaseT
port (Control Communications must
be set to On)
s Extended > HDBaseT > Control
Communications
Communication On is automatically
selected when A/V Output is set to
Always On.
s Extended > A/V Settings > A/V
Output
ECO Display
On
Off
Displays a leaf icon in the bottom left
corner of the projected screen to indicate
the power-saving status when the lamp
brightness changes (when On).
Reset
—
Resets all adjustment values on the ECO
menu to their default settings, except for
Standby Mode.
* Available only for EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG.
a
• When the Sleep Mode Timer setting is enabled, the lamp dims for a
short time before the timer limit is reached and the projector turns
off.
• When the Lens Cover Timer or A/V Mute Timer settings are
enabled, the lamp uses less power when the lens cover is closed or
A/V Mute is activated.
160
g Related Links
• "Projector Setup Settings - Extended Menu" p.147
Projector Information Display - Info Menu
You can display information about the projector and version by viewing the
Info menu. However, you cannot change any settings in the menu.
161
Info Menu - Projector Info Menu
You can display information about the projector and input sources by viewing
the Projector Info menu in the projector's Info menu.
Information item
Description
Projector Info
Displays the projector information.
Version
Displays the projector's firmware version.
a
g Related Links
• "Info Menu - Projector Info Menu" p.161
The available settings depend on the current input source. The lamp
usage timer does not register any hours until you have used the lamp
for at least 10 hours.
Information item
Description
Lamp Hours
Displays the number of hours (H) the lamp has been
used in Normal and ECO Power Consumption modes;
if the information is displayed in yellow, obtain a
genuine Epson replacement lamp soon.
Source
Displays the name of the port to which the current
input source is connected.
Input Signal
Displays the input signal setting of the current input
source.
Resolution
Displays the resolution of the current input source.
Projector Information Display - Info Menu
Information item
Description
Video Signal
Displays the video signal format of the current input
source.
Refresh Rate
Displays the refresh rate of the current input source.
Sync Info
Displays information that may be needed by a service
technician.
Status
162
Event ID
code
Cause and solution
A screen mirroring communication error has occurred. Turn the
projector off and then on again, or restart the network software.
Displays information about projector problems that
may be needed by a service technician.
0020
0026
0032
0036
0037
0038
Serial Number
Displays the projector's serial number.
0021
Event ID
Displays the Event ID number corresponding to a
network problem; see the list of Event ID codes.
Failed to startup Screen Mirroring. Turn the projector off and then
on again.
HDBaseT Signal Level *
Displays the signal level of the HDBaseT transmitter; if
the information is displayed in yellow, signal level is
not enough.
0022
0027
0028
0029
0030
0031
0035
Unstable screen mirroring communication. Check the network
communication status, wait a few moments, and try connecting to
the network again.
0023
0024
0025
Connection failed. If you see the PIN entry screen on your
computer, enter the PIN code displayed on the Screen Mirroring
standby screen or at the bottom right of the projected image. If this
does not solve the problem, restart the projector and the connected
devices, and then check the connection settings.
0041
Connection failed. Delete the recorded projector information on
your computer and try connecting again.
0432
0435
The network software did not start. Turn the projector off and then
on again.
0433
Cannot display the transferred images. Restart the network software.
0434
0481
0482
0485
Unstable network communication. Check the network
communication status, wait a few moments, and try connecting to
the network again.
0483
04FE
The network software quit unexpectedly. Check the network
communication status, then turn the projector off and then on again.
* Available only for EB-2265U/EB-2165W.
g Related Links
• "Event ID Code List" p.162
Event ID Code List
If the Event ID option on the Projector Info menu displays a code number,
check this list of Event ID codes for the solution to the projector problem
associated with the code.
If you cannot resolve the problem, contact your network administrator or
Epson for technical support.
Projector Information Display - Info Menu
Event ID
code
Cause and solution
0484
Communication with computer was disconnected. Restart the
network software.
0479
04FF
A projector system error has occurred. Turn the projector off and
then on again.
0891
Cannot find an access point with the same SSID. Set your computer,
access point, and projector to the same SSID.
0892
The WPA/WPA2 authentication type does not match. Make sure the
wireless network security settings are correct.
0893
The TKIP/AES encryption type does not match. Make sure the
wireless network security settings are correct.
0894
Communication with an unauthorized access point was
disconnected. Contact your network administrator.
0898
Failed to acquire DHCP. Make sure the DHCP server is operating
correctly. If you are not using DHCP, set the DHCP setting to Off in
the projector's Network menu.
s Network > Network Configuration > Wireless LAN > IP
Settings > DHCP
s Network > Network Configuration > Wired LAN > IP Settings
> DHCP
0899
Other communication errors.
089A
The EAP authentication type does not match the network. Check the
wireless LAN security settings and make sure that the security
certificate is installed correctly.
089B
EAP server authentication failed. Check the wireless LAN security
settings and make sure that the security certificate is installed
correctly.
089C
EAP client authentication failed. Check the wireless LAN security
settings and make sure that the security certificate is installed
correctly.
089D
Key exchange failed. Check the wireless LAN security settings and
make sure that the security certificate is installed correctly.
163
Projector Reset Options - Reset Menu
You can reset most of the projector settings to their default values using the
Reset menu.
164
• Network menu items
• Lamp Hours
• Password
* Available when you have save a user's logo.
Setting
Options
Description
Reset Lamp Hours
—
Reset the projector's lamp usage timer to
zero when you replace the lamp.
Reset All Config
—
Resets most of the projector settings to
their default values.
You cannot reset the following settings using the Reset All Config option:
•
•
•
•
•
•
•
•
•
Input Signal
User's Logo
Display Background *
Startup Screen *
A/V Mute *
Color Matching
Schedule Settings
Language
Date & Time
Copying Menu Settings Between Projectors (Batch Setup)
After selecting the projector's menu settings for one projector, you can use the
following methods to copy the settings to other projectors, as long as they are
the same model.
• by using a USB flash drive
• by connecting a computer and projector using a USB cable
• by using EasyMP Network Updater
Menu settings such as the following are not copied to the other projector.
• Network menu settings (except for the Notifications menu and the Others
menu)
• Lamp Hours and Status from the Projector Info menu
a
Perform batch setup before adjusting the image settings such as
Keystone. Since image adjustment values are also copied to another
projector, the adjustments you made before performing the batch setup
are overwritten and the projected screen you adjusted may change.
When copying the menu settings from one projector to another, user's
logo is also copied. Do not register the information that you do not
want to share between multiple projectors as a user's logo.
Caution
Epson takes no responsibility for batch setup failures and associated repair costs
due to power outages, communication errors, or other problems that may cause
such failures.
g Related Links
• "Transferring Settings From a USB Flash Drive" p.165
• "Transferring Settings From a Computer" p.166
Transferring Settings From a USB Flash Drive
You can copy menu settings from one projector to another of the same model
using a USB flash drive.
a
165
The USB flash drive must use a FAT format and not incorporate any
security function. Delete any files on the drive before using it for batch
setup or the settings may not be saved correctly.
the power cord from the projector, and check that all of the
a Disconnect
projector's indicators have turned off.
an empty USB flash drive directly to the projector's USB-A
b Connect
port.
down the [Esc] button on the remote control or the control panel
c Hold
and connect the power cord to the projector.
all of the projector's indicators turn on, release the [Esc] button.
d When
The indicators start flashing and the batch setup file is written to the
USB flash drive. When writing is finished, the projector turns off.
Caution
Do not disconnect the power cord or the USB flash drive from the projector
while the file is being written. If the power cord or USB flash drive is
disconnected, the projector may not start correctly.
e Remove the USB flash drive.
a
The file name for the batch setup file is PJCONFDATA.bin. If
you need to change the file name, add text after PJCONFDATA
using only alphanumeric characters. If you change the
PJCONFDATA section of the file name, the projector may not be
able to recognize the file correctly.
the power cord from the projector to which you want to
f Disconnect
copy settings, and check that all of the projector's indicators have
turned off.
Copying Menu Settings Between Projectors (Batch Setup)
the USB flash drive containing the saved batch setup file to the
g Connect
projector's USB-A port.
down the [Menu] button on the remote control or the control
h Hold
panel and connect the power cord to the projector.
all of the projector's indicators turn on, release the [Menu]
i When
button.
When all of the indicators start flashing, the settings are being written.
When writing is finished, the projector turns off.
Caution
Do not disconnect the power cord or the USB flash drive from the projector
while the file is being written. If the power cord or drive is disconnected,
the projector may not start correctly.
j Remove the USB flash drive.
Transferring Settings From a Computer
You can copy menu settings from one projector to another of the same model
by connecting the computer and projector with a USB cable.
a
You can use this batch setup method with the following operating
system versions:
• Windows Vista and later
• OS X 10.7.x and later
the power cord from the projector, and check that all of the
a Disconnect
projector's indicators have turned off.
a USB cable to the computer's USB port and to the projector's
b Connect
USB-B port.
166
down the [Esc] button on the remote control or the control panel
c Hold
and connect the power cord to the projector.
all of the projector's indicators turn on, release the [Esc] button.
d When
The computer recognizes the projector as a removable disk.
the removable disk icon or folder, and save the batch setup file to
e Open
the computer.
a
The file name for the batch setup file is PJCONFDATA.bin. If
you need to change the file name, add text after PJCONFDATA
using only alphanumeric characters. If you change the
PJCONFDATA section of the file name, the projector may not be
able to recognize the file correctly.
the USB device (Windows) or drag the removable disk icon to the
f Eject
Trash (OS X).
the USB cable.
g Disconnect
The projector turns off.
the power cord from the projector to which you want to
h Disconnect
copy settings, and check that all of the projector's indicators have
turned off.
the USB cable to the computer's USB port and to the
i Connect
projector's USB-B port.
down the [Menu] button on the remote control or the control
j Hold
panel and connect the power cord to the projector.
all of the projector's indicators turn on, release the [Menu]
k When
button.
The computer recognizes the projector as a removable disk.
Copying Menu Settings Between Projectors (Batch Setup)
the batch setup file (PJCONFDATA.bin) that you saved to your
l Copy
computer to the top level folder of the removable disk.
a
Indicator status
m
the USB cable.
n Disconnect
When all of the indicators start flashing, the settings are being written.
• Lamp: Orange - flashing
fast
• Temp: Orange - flashing
fast
Writing the settings may have failed and an error may
have occurred in the projector's firmware.
Stop using the projector, remove the power plug from
the electrical outlet. Contact Epson for help.
When writing is finished, the projector turns off.
Caution
Do not disconnect the power cord from the projector while the file is being
written. If the power cord is disconnected, the projector may not start
correctly.
g Related Links
• "Batch Setup Error Notification" p.167
Batch Setup Error Notification
The projector's indicators notify you if an error occurs during a batch setup
operation. Check the status of the projector's indicators and follow the
instructions described in the table here.
Problem and solution
The batch setup file may be corrupt, or the USB flash
drive may not be connected correctly.
Disconnect the USB flash drive, unplug and then plug
in the projector's power cord, and then try again.
Do not copy any files or folders other than the batch setup file to
the removable disk.
Eject the USB device (Windows) or drag the removable disk icon to the
Trash (OS X).
167
• Power: Blue - flashing
fast
• Status: Blue - flashing
fast
• Lamp: Orange - flashing
fast
• Temp: Orange - flashing
fast
Maintaining the Projector
You may need to clean the projector's lens periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation.
The only parts you should replace are the lamp, air filter, and remote control batteries. If any other part needs replacing, contact Epson or an authorized Epson servicer.
Warning
Before cleaning any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except as specifically explained in this manual. Dangerous
electrical voltages in the projector can injure you severely.
g Related Links
• "Cleaning the Lens" p.169
• "Cleaning the Projector Case" p.170
• "Air Filter and Vent Maintenance" p.171
• "Projector Lamp Maintenance" p.173
• "Replacing the Remote Control Batteries" p.180
Cleaning the Lens
Clean the projector's lens periodically, or whenever you notice dust or
smudges on the surface.
• To remove dust or smudges, gently wipe the lens with lens-cleaning paper.
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens
cleaner and gently wipe the lens. Do not spray any liquid directly on the
lens.
Warning
Do not use a lens cleaner that contains flammable gas. The high heat generated
by the projector lamp may cause a fire.
Attention
Do not use glass cleaner or any harsh materials to clean the lens and do not
subject the lens to any impacts; otherwise, it could be damaged. Do not use
canned air, or the gases may leave a flammable residue.
169
Cleaning the Projector Case
Before cleaning the projector case, turn off the projector and unplug the
power cord.
• To remove dust or dirt, use a soft, dry, lint-free cloth.
• To remove stubborn dirt, use a soft cloth moistened with water and mild
soap. Do not spray liquid directly on the projector.
Attention
Do not use wax, alcohol, benzene, paint thinner, or other chemicals to clean the
projector case. These can damage the case. Do not use canned air, or the gases
may leave a flammable residue.
170
Air Filter and Vent Maintenance
Regular filter maintenance is important to maintaining your projector. Clean
the air filer when a message appears telling you the temperature inside the
projector has reached a high level. It is recommended that you clean these
parts at least once every three months. Clean them more often than this if you
use the projector in a particularly dusty environment.
Attention
If regular maintenance is not performed, your Epson projector will notify you
when the temperature inside the projector has reached a high level. Do not wait
until this warning appears to maintain your projector filter as prolonged exposure
to high temperatures may reduce the life of your projector or lamp.
g Related Links
• "Cleaning the Air Filter and Vents" p.171
• "Replacing the Air Filter" p.171
171
a
You can remove the air filter so that you can clean both sides. Do
not rinse the air filter in water, or use any detergent or solvent to
clean it.
Attention
Do not use canned air. The gases may leave a flammable residue or push
dust and debris into the projector's optics or other sensitive areas.
dust is difficult to remove or the air filter is damaged, replace the air
c Iffilter.
Replacing the Air Filter
You need to replace the air filter in the following situations:
Cleaning the Air Filter and Vents
Clean the projector's air filter or vents if they get dusty, or if you see a
message telling you to clean them.
a Turn off the projector and unplug the power cord.
remove the dust using a small vacuum designed for computers
b Gently
or a very soft brush (such as a paintbrush).
• After cleaning the air filter, you see a message telling you to clean or replace
it
• The air filter is torn or damaged
You can replace the air filter while the projector is mounted to the ceiling or
placed on a table.
a Turn off the projector and unplug the power cord.
Air Filter and Vent Maintenance
b Slide the air filter cover latch and open the air filter cover.
172
the new air filter in the projector as shown and push gently until
d Place
it clicks into place.
c Pull the air filter out of the projector.
e Close the air filter cover.
g Related Links
• "Replacement Parts" p.199
a
Dispose of used air filters according to local regulations.
• Filter frame: Polypropylene
• Filter: Polypropylene
Projector Lamp Maintenance
The projector monitors the number of hours the lamp is used and displays
this information in the projector's menu system.
Replace the lamp as soon as possible when the following occurs:
• The projected image gets darker or quality declines
• A message is displayed when you turn on the projector telling you to replace
the lamp (the message is displayed 100 hours before the expected end of the
lamp life and appears for 30 seconds)
173
• The projector's power indicator is flashing blue and its lamp indicator is
flashing orange.
Projector Lamp Maintenance
Attention
• If you continue to use the lamp after the replacement period has passed, the
possibility that the lamp may explode increases. When the lamp replacement
message appears, replace the lamp with a new one as soon as possible, even if it
is still working.
• Do not repeatedly turn off the power and then immediately turn it back on.
Turning the power on and off frequently may shorten the lamp's operating life.
• Depending on the characteristics of the lamp and the way it has been used, the
lamp may become darker or stop working before the lamp warning message
appears. You should always have a spare lamp unit ready in case it is needed.
• We recommend the use of genuine Epson replacement lamps. The use of nongenuine lamps may affect projection quality and safety. Any damage or
malfunction caused by the use of non-genuine lamps may not be covered by
Epson's warranty.
g Related Links
• "Replacing the Lamp" p.174
• "Resetting the Lamp Timer" p.179
• "Projector Specifications" p.206
Replacing the Lamp
You can replace the lamp while the projector is placed on a table or mounted
to the ceiling.
Warning
• Let the lamp fully cool before replacing it to avoid injury.
• Never disassemble or modify the lamp. If a modified or disassembled lamp is
installed in the projector, it could cause a fire, electric shock, or other damage or
injury.
a Turn off the projector and unplug the power cord.
b Allow the projector lamp to cool down for at least one hour.
174
the screwdriver included with the replacement lamp to loosen the
c Use
screw securing the lamp cover.
Warning
When replacing the lamp, there is a possibility that the lamp may be
broken. If replacing the lamp of a projector which has been installed on the
ceiling, you should always assume that the lamp is cracked, and you should
stand to the side of the lamp cover, not underneath it. Remove the lamp
cover gently. Be careful when removing the lamp cover as shards of glass
may fall out and could cause an injury. If any shards of glass get into your
eyes or mouth, contact a doctor immediately.
Projector Lamp Maintenance
d Slide the lamp cover out and lift it off.
175
the screws securing the lamp to the projector. The screws do
e Loosen
not come all the way out.
• EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB-2165W/EB2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG:
Projector Lamp Maintenance
• EB-2140W/EB-2040:
176
the lamp.
f Remove
• EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB-2165W/EB-
2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG: Lift up the
lamp handle and carefully pull the lamp out of the projector.
• EB-2140W/EB-2040: Grasp the raised section of the lamp and gently
pull the lamp out of the projector.
Projector Lamp Maintenance
a
• If you notice the lamp is cracked when removing the lamp,
replace it with a new lamp, or contact Epson for help.
• The lamp(s) in this product contain mercury (Hg). Check your
local laws and regulations regarding disposal or recycling. Do
not put in the trash.
177
• EB-2140W/EB-2040: Gently insert the new lamp into the projector.
If it does not fit easily, make sure it is facing the right way.
the new lamp.
g Install
• EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB-2165W/EB-
2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG: Gently insert
the new lamp into the projector. If it does not fit easily, make sure it
is facing the right way. Press the handle down.
Attention
Do not touch any glass on the lamp assembly to avoid premature lamp
failure.
Projector Lamp Maintenance
in the lamp firmly and tighten the screws to secure it.
h Push
• EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB-2165W/EB-
178
• EB-2140W/EB-2040:
2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG:
i Replace the lamp cover and tighten the screw to secure it.
Projector Lamp Maintenance
a
• Make sure the lamp cover is securely installed or the lamp will
not turn on.
• Do not replace the lamp cover with too much force and make
sure the lamp cover is not deformed.
179
d Select Reset Lamp Hours and press [Enter].
Reset the lamp timer to zero to monitor the new lamp's usage.
g Related Links
• "Replacement Parts" p.199
Resetting the Lamp Timer
You must reset the lamp timer after replacing the projector's lamp to clear the
lamp replacement message and to monitor lamp usage correctly.
a
Do not reset the lamp timer if you have not replaced the lamp to avoid
inaccurate lamp usage information.
a Turn on the projector.
b Press the [Menu] button on the control panel or remote control.
c Select the Reset menu and press [Enter].
You see a prompt asking if you want to reset the lamp hours.
e Select Yes and press [Enter].
f Press [Menu] or [Esc] to exit the menus.
Replacing the Remote Control Batteries
The remote control uses two AA manganese or alkaline batteries. Replace the
batteries as soon as they run out.
Attention
Make sure you read the Safety Instructions before handling the batteries.
a Remove the battery cover as shown.
b Remove the old batteries.
c Insert the batteries with the + and – ends facing as shown.
180
Warning
Check the positions of the (+) and (–) marks inside the battery holder to
ensure the batteries are inserted the correct way. If the batteries are not used
correctly, they could explode or leak causing a fire, injury, or damage to the
product.
d Replace the battery cover and press it down until it clicks into place.
Solving Problems
Check the solutions in these sections if you have any problems using the projector.
g Related Links
• "Projection Problems" p.182
• "Projector Indicator Status" p.183
• "Using the Projector Help Displays" p.185
• "Solving Image or Sound Problems" p.186
• "Solving Projector or Remote Control Operation Problems" p.192
• "Solving Network Problems" p.194
Projection Problems
If the projector is not working properly, turn it off, unplug it, and then plug it
back in and turn it on.
If this does not solve the problem, check the following:
• The indicators on the projector may indicate the problem.
• The projector's Help system can display information about common
problems.
• The solutions in this manual can help you solve many problems.
If none of these solutions help, contact Epson for technical support.
182
Projector Indicator Status
The indicators on the projector indicate the projector status and let you know
when a problem occurs. Check the status and color of the indicators and then
refer to this table for a solution.
a
• If the indicators display a pattern not listed in the table below, turn
the projector off, unplug it, and contact Epson for help.
A On/Standby (power) indicator
B Status indicator
C Lamp indicator
D Temp (temperature) indicator
183
Projector status
Indicator and status
Problem and solutions
Power: Lit blue
Status: Lit blue
Lamp: Off
Temp: Off
Normal operation.
Power: Lit blue
Status: Flashing blue
Lamp: Off
Temp: Off
Warming up or shutting down. When warming up, wait
about 30 seconds for an image to appear.
All buttons are disabled during warm-up and shutting
down.
Power: Lit blue
Status: Off
Lamp: Off
Temp: Off
Standby, sleep mode, or monitoring.
When you press the power button, projection starts.
Power: Flashing blue
Status: Off
Lamp: Off
Temp: Off
Preparing for monitoring and all features are disabled.
Power: Flashing blue
Status: Indicator status
varies
Lamp: Indicator status
varies
Temp: Flashing orange
Projector is too hot.
• Make sure that the vents and air filter are not clogged
with dust or obstructed by nearby objects.
• Clean or replace the air filter.
• Make sure the environmental temperature is not too
hot.
Projector Indicator Status
184
Indicator and status
Problem and solutions
Indicator and status
Problem and solutions
Power: Off
Status: Flashing blue
Lamp: Off
Temp: Lit orange
Projector has overheated and turned off. Leave it turned
off to cool down for 5 minutes.
• Make sure that the vents and air filter are not clogged
with dust or obstructed by nearby objects.
• Clean or replace the air filter.
• If operating the projector at high altitude, set the High
Altitude Mode setting to On in the projector's
Extended menu.
s Extended > Operation > High Altitude Mode
• If the problem persists, unplug the projector and
contact Epson for help.
Power: Off
Status: Flashing blue
Lamp: Off
Temp: Flashing orange
A fan or sensor has a problem. Turn the projector off,
unplug it, and contact Epson for help.
Power: Off
Status: Flashing blue
Lamp: Flashing orange
Temp: Off
Internal projector error. Turn the projector off, unplug
it, and contact Epson for help.
Power: Off
Status: Flashing blue
Lamp: Flashing orange
Temp: Flashing orange
Auto iris error. Turn the projector off, unplug it, and
contact Epson for help.
Power: Off
Status: Flashing blue
Lamp: Lit orange
Temp: Lit orange
Power error (Ballast). Turn the projector off, unplug it,
and contact Epson for help.
Power: Off
Status: Flashing blue
Lamp: Lit orange
Temp: Off
Power: Flashing blue
Status: Indicator status
varies
Lamp: Flashing orange
Temp: Indicator status
varies
Lamp has a problem.
• Check to see if the lamp is burned out, broken, or
installed incorrectly. Reseat or replace the lamp as
necessary.
• Clean the air filter.
• If operating the projector at high altitude, set the High
Altitude Mode setting to On in the projector's
Extended menu.
s Extended > Operation > High Altitude Mode
• If the problem persists, unplug the projector and
contact Epson for help.
Lamp cover has a problem.
• Check that the lamp and the lamp cover are securely
installed. The lamp does not turn on if the lamp and
the lamp cover are not installed correctly.
Replace the lamp soon to avoid damage. Do not
continue using the projector.
g Related Links
• "Cleaning the Air Filter and Vents" p.171
• "Replacing the Air Filter" p.171
• "Replacing the Lamp" p.174
Using the Projector Help Displays
You can display information to help you solve common problems using the
projector's Help system.
185
the up and down arrow buttons to highlight the problem you want
d Use
to solve.
a Turn on the projector.
b Press the [Home] button on the control panel or remote control.
c Select Help on the Home screen.
e Press [Enter] to view the solutions.
one of the following actions when you are finished.
f Perform
• To select another problem to solve, press [Esc].
• To exit the help system, press [Menu].
The Help menu is displayed.
Solving Image or Sound Problems
Check the solutions in these sections if you have any problems with projected
images or sound.
g Related Links
• "Solutions When No Image Appears" p.186
• "Solutions When Image is Incorrect Using the USB Display Function" p.187
• "Solutions When "No Signal" Message Appears" p.187
• "Solutions When "Not Supported" Message Appears" p.188
• "Solutions When Only a Partial Image Appears" p.188
• "Solutions When the Image is not Rectangular" p.188
• "Solutions When the Image Contains Noise or Static" p.189
• "Solutions When the Image is Fuzzy or Blurry" p.189
• "Solutions When the Image Brightness or Colors are Incorrect" p.190
• "Solutions to Sound Problems" p.190
• "Solutions When Image File Names are not Displayed Correctly in PC Free"
p.191
Solutions When No Image Appears
If no image appears, try the following solutions:
• Press the power button to turn the power on.
• Make sure the lens cover is open all the way.
• Press the [A/V Mute] button on the remote control to see if the image was
temporarily turned off.
• Make sure all necessary cables are securely connected and the power is on
for the projector and connected video sources.
• Make sure the image being projected is not completely black (only when
projecting computer images).
• Make sure the projector's menu settings are correct.
• Press the projector's power button to wake it from standby or sleep mode.
Also, check if the connected computer is in sleep mode or displaying a
blank screen saver.
• To project an image source connected to the Computer2/Monitor Out port,
set Monitor Out Port to Computer2 in the projector's Extended menu.
186
s Extended > Operation > Monitor Out Port
• Check the settings on the projector's Signal menu to make sure they are
correct for the current video source.
• Adjust the Brightness setting in the projector's Image menu.
• Select Normal as the Power Consumption setting.
s ECO > Power Consumption
• Check the Display setting in the projector's Extended menu to make sure
Messages is set to On.
• If the projector does not respond when you press the control panel buttons,
the buttons may be locked for security. Unlock the buttons in the Control
Panel Lock setting in the projector's Settings menu or use the remote
control to turn on the projector.
s Settings > Lock Setting > Control Panel Lock
• If the projector does not respond when you press buttons on the remote
control, make sure the remote receivers are turned on.
• For images projected with Windows Media Center, reduce the screen size
from full screen mode.
• For images projected from applications using Windows DirectX, turn off
DirectX functions.
• The projector may not be able to project copyrighted videos that you play
back on a computer. For more details, see the manual supplied with the
computer.
g Related Links
• "Input Signal Settings - Signal Menu" p.143
• "Image Quality Settings - Image Menu" p.141
• "Projector Setup Settings - ECO Menu" p.159
• "Projector Setup Settings - Extended Menu" p.147
• "Unlocking the Projector's Buttons" p.98
Solving Image or Sound Problems
Solutions When Image is Incorrect Using the USB
Display Function
If no image appears or if the image appears incorrectly using the USB Display
function, try the following solutions:
• Press the [USB] button on the remote control.
• Make sure the Epson USB Display software has been installed correctly.
Install it manually if necessary.
• For OS X, select the USB Display icon in the Dock folder. If the icon does
not appear on the Dock, double-click USB Display in the Applications
folder.
If you select Exit from the USB Display icon menu on the Dock, USB
Display does not start automatically when you connect the USB cable.
• For images projected with Windows Media Center, reduce the screen size
from full screen mode.
• For images projected from applications using Windows DirectX, turn off
DirectX functions.
• If the mouse cursor flickers, select Make the movement of the mouse
pointer smooth in the Epson USB Display Settings program on your
computer.
• Turn off the Transfer layered window setting in the Epson USB Display
Settings program on your computer.
• For projectors with a resolution of WUXGA (1920 × 1200), if you change
the computer resolution during projection, the performance and quality of
the video may decline.
g Related Links
• "Connecting to a Computer for USB Video and Audio" p.23
Solutions When "No Signal" Message Appears
If the "No Signal" message appears, try the following solutions:
187
• Press the [Source Search] button and wait a few seconds for an image to
appear.
• Turn on the connected computer or video source, and press play to begin
your presentation, if necessary.
• Check that all cables required for projection are securely connected.
• Connect the video source directly to the projector.
• If you are projecting from a laptop computer, make sure it is set up to
display on an external monitor.
• Make sure the connected computer is not in sleep mode.
• If necessary, turn off the projector and the connected computer or video
source, and then turn them back on.
• If you are projecting from an HDMI source, replace the HDMI cable with
the shorter one.
g Related Links
• "Displaying From a Laptop" p.187
• "Displaying From a Mac Laptop" p.188
Displaying From a Laptop
If the message "No Signal" is displayed when projecting from a laptop, you
need to set up the laptop to display on an external monitor.
down the laptop's Fn key and press the key labeled with a monitor
a Hold
icon or CRT/LCD. (See your laptop manual for details.) Wait a few
seconds for an image to appear.
on the laptop's monitor and the projector, try pressing the
b Tosamedisplay
keys again.
same image is not displayed by the laptop and projector, check
c IfthetheWindows
Display utility to make sure the external monitor port is
enabled and extended desktop mode is disabled. (See your computer or
Windows manual for instructions.)
Solving Image or Sound Problems
necessary, check your video card settings and set the multiple display
d Ifoption
to Clone or Mirror.
Displaying From a Mac Laptop
If the message "No Signal" is displayed when projecting from a Mac laptop,
you need to set up the laptop for mirrored display. (See your laptop manual
for details.)
a Open the System Preferences utility and select Displays.
b Select the Display or Color LCD option, if necessary.
c Click the Arrange or Arrangement tab.
d Select Mirror Displays.
Solutions When "Not Supported" Message Appears
If the message "Not supported" is displayed, try the following solutions:
• Make sure the correct input signal is selected on the projector's Signal
menu.
• Make sure the computer's display resolution does not exceed the projector's
resolution and frequency limits. If necessary, select a different display
resolution for your computer. (See your computer manual for details.)
g Related Links
• "Input Signal Settings - Signal Menu" p.143
• "Supported Monitor Display Resolutions" p.204
Solutions When Only a Partial Image Appears
If only a partial computer image appears, try the following solutions:
188
• Press the [Auto] button on the remote control to optimize the image signal.
• Try adjusting the image position using the Position setting in the
projector's Signal menu.
• Press the [Aspect] button on the remote control to select a different image
aspect ratio.
• Change the Resolution setting in the projector's Signal menu according to
the signal for the connected equipment.
• If you zoomed into or out of the image using the [E-Zoom] buttons, press
the [Esc] button until the projector returns to a full display.
• Check your computer display settings to disable dual display and set the
resolution within the projector's limits. (See your computer manual for
details.)
• Check the resolution assigned to your presentation files to see if they are
created for a different resolution. (See your software help for details.)
• Make sure you selected the correct projection mode. You can select this
using the Projection setting in the projector's Extended menu.
g Related Links
• "Input Signal Settings - Signal Menu" p.143
• "Projector Setup Settings - Extended Menu" p.147
• "Supported Monitor Display Resolutions" p.204
Solutions When the Image is not Rectangular
If the projected image is not evenly rectangular, try the following solutions:
• Place the projector directly in front of the center of the screen, facing it
squarely, if possible.
• Turn on automatic adjustment in the projector's Settings menu. The
projector automatically corrects the image every time you move the
projector.
s Settings > Keystone > H/V-Keystone > Auto H/V-Keystone
s Settings > Keystone > H/V-Keystone > Auto V-Keystone
Solving Image or Sound Problems
• Press the [Screen Fit] button and adjust the image shape using the onscreen display (EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB-2165W/EB2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG).
• Turn on horizontal keystone slider in the projector's Settings menu. Then
adjust the slider until the image is evenly rectangular (EB-2140W/EB-2040).
s Settings > Keystone > H/V-Keystone > H-Keystone Adjuster
• If you adjusted the projector height using the projector feet, press the
keystone buttons on the projector to adjust the image shape.
• Adjust the Quick Corner setting to correct the image shape.
s Settings > Keystone > Quick Corner
g Related Links
• "Auto H/V-Keystone" p.47
• "Auto V-Keystone" p.47
• "Automatically Correcting the Image Shape with Screen Fit" p.47
• "Correcting the Image Shape with the Keystone Buttons" p.50
• "Correcting the Image Shape with Quick Corner" p.51
• "Correcting the Image Shape with the Horizontal Keystone Slider" p.49
Solutions When the Image Contains Noise or Static
If the projected image contains electronic interference (noise) or static, try the
following solutions:
• Check the cables connecting your computer or video source to the
projector. They should be:
• Separated from the power cord to prevent interference
• Securely connected at both ends
• Not connected to an extension cable
• Check the settings on the projector's Signal menu to make sure they match
the video source.
• If available for your video source, adjust the Deinterlacing and Noise
Reduction settings in the projector's Image menu.
s Image > Advanced > Deinterlacing
s Image > Image Enhancement > Noise Reduction
189
• Select a computer video resolution and refresh rate that are compatible with
the projector.
• If you are projecting from a computer, press the [Auto] button on the
remote control to automatically adjust the Tracking and Sync. settings. If
the images are not adjusted correctly, manually adjust the Tracking and
Sync. settings in the projector's Signal menu.
• Select Auto as the Resolution setting in the projector's Signal menu.
• If you adjusted the image shape using the projector controls, try decreasing
the Sharpness setting in the projector's Image menu to improve image
quality.
• If you connected an extension power cable, try projecting without it to see if
it caused interference in the signal.
• If you are using the USB Display function, turn off the Transfer layered
window setting in the Epson USB Display Settings program on your
computer.
g Related Links
• "Input Signal Settings - Signal Menu" p.143
• "Image Quality Settings - Image Menu" p.141
• "Supported Monitor Display Resolutions" p.204
Solutions When the Image is Fuzzy or Blurry
If the projected image is fuzzy or blurry, try the following solutions:
• Adjust the image focus.
• Clean the projector lens.
a
To avoid condensation on the lens after bringing the projector in
from a cold environment, let the projector warm up to room
temperature before using it.
• Position the projector close enough to the screen.
• Position the projector so the keystone adjustment angle is not so wide that it
distorts the image.
Solving Image or Sound Problems
• When using the Screen Fit feature, position the projector at a compatible
distance from the screen or adjust the image shape manually (EB2265U/EB-2255U/EB-2250U/EB-2245U/EB-2165W/EB-2155W/EB2065/EB-2055/EB-X550KG/EB-X500KG).
• Turn on automatic adjustment in the projector's Settings menu.
s Settings > Keystone > H/V-Keystone > Auto H/V-Keystone
s Settings > Keystone > H/V-Keystone > Auto V-Keystone
• Adjust the Sharpness setting in the projector's Image menu to improve
image quality.
• If you are projecting from a computer, press the [Auto] button on the
remote control to automatically adjust the tracking and sync. If any bands
or overall blurriness remain, display a uniformly patterned image on the
screen and manually adjust the Tracking and Sync. settings in the
projector's Signal menu.
• If you are projecting from a computer, use a lower resolution or select a
resolution that matches the projector's native resolution.
g Related Links
• "Auto H/V-Keystone" p.47
• "Auto V-Keystone" p.47
• "Input Signal Settings - Signal Menu" p.143
• "Image Quality Settings - Image Menu" p.141
• "Supported Monitor Display Resolutions" p.204
• "Focusing the Image Using the Focus Ring" p.55
• "Cleaning the Lens" p.169
Solutions When the Image Brightness or Colors are
Incorrect
If the projected image is too dark or light, or the colors are incorrect, try the
following solutions:
• Press the [Color Mode] button on the remote control to try different color
modes for the image and environment.
• Check your video source settings.
190
• Adjust the available settings on the projector's Image menu for the current
input source, such as Brightness, Contrast, Tint, Color Temp., and/or
Color Saturation.
• Make sure you selected the correct Input Signal or Video Signal setting in
the projector's Signal menu, if available for your image source.
s Signal > Advanced > Input Signal
s Signal > Advanced > Video Signal
• Make sure you selected the correct Gamma or RGBCMY setting in the
projector's Image menu.
s Image > Advanced
• Make sure all the cables are securely connected to the projector and your
video device. If you connected long cables, try connecting shorter cables.
• If you are using ECO as Power Consumption, try selecting Normal.
s ECO > Power Consumption
a
At high altitudes or locations subject to high temperatures, the image
may become darker and you may not be able to adjust the Power
Consumption setting.
• Position the projector close enough to the screen.
• If the image has been progressively darkening, you may need to replace the
projector lamp soon.
g Related Links
• "Color Mode" p.60
• "Input Signal Settings - Signal Menu" p.143
• "Image Quality Settings - Image Menu" p.141
• "Projector Setup Settings - ECO Menu" p.159
Solutions to Sound Problems
If there is no sound or the volume is too low or high, try the following
solutions:
• Adjust the projector's volume settings.
Solving Image or Sound Problems
• Press the [A/V Mute] button on the remote control to resume video and
audio if they were temporarily stopped.
• Check your computer or video source to make sure the volume is turned up
and the audio output is set for the correct source.
• Disconnect the audio cable, and then reconnect it.
• Check the audio cable connections between the projector and your video
source.
• If you do not hear sound from an HDMI source, set the connected device to
PCM output.
• Make sure any connected audio cables are labeled "No Resistance".
• If you are using the USB Display function, turn on the Output audio from
the projector setting in the Epson USB Display Settings program on your
computer.
• Select the correct audio input in the A/V Settings setting in the projector's
Extended menu.
• When you are connecting the projector to a Mac using an HDMI cable,
make sure your Mac supports audio through the HDMI port. If not, you
need to connect an audio cable.
• If you want to use a connected audio source when the projector is off, set
the Standby Mode option to Communication On in the projector's ECO
menu and make sure the A/V Settings options are set correctly in the
projector's Extended menu.
• If the volume for the computer is set to the minimum while the projector is
set to the maximum, the noise may be mixed. Turn up the computer's
volume and turn down the projector's volume. (When you use EasyMP
Multi PC Projection or USB Display.)
g Related Links
• "Projector Connections" p.23
• "Projector Setup Settings - Extended Menu" p.147
• "Projector Setup Settings - ECO Menu" p.159
• "Controlling the Volume with the Volume Buttons" p.66
191
Solutions When Image File Names are not Displayed
Correctly in PC Free
If any file names are longer than the display area or include unsupported
symbols, the file names are shortened or changed in PC Free. Shorten or
change the file name.
Solving Projector or Remote Control Operation Problems
Check the solutions in these sections if you have problems operating the
projector or remote control.
g Related Links
• "Solutions to Projector Power or Shut-Off Problems" p.192
• "Solutions to Problems with the Remote Control" p.192
• "Solutions to Password Problems" p.193
• "Solution When "The Battery that Saves Your Clock Settings is Running
Low" Message Appears" p.193
• "Solutions to Gesture Presenter Problems" p.193
Solutions to Projector Power or Shut-Off Problems
If the projector does not turn on when you press the power button or it turns
off unexpectedly, try the following solutions:
• Make sure the power cord is securely connected to the projector and to a
working electrical outlet.
• The projector's buttons may be locked for security. Unlock the buttons in
the Control Panel Lock setting in the projector's Settings menu or use the
remote control to turn on the projector.
s Settings > Lock Setting > Control Panel Lock
• The power cord may be defective. Disconnect the cord and contact Epson
for help.
• If the projector's lamp turns off unexpectedly, it may have entered sleep
mode after a period of inactivity. Perform any operation to wake the
projector. To turn off sleep mode, select Off as the Sleep Mode setting in
the projector's ECO menu.
• If the projector's lamp turns off unexpectedly, the A/V mute timer may be
enabled. To turn off the A/V mute timer, select Off as the A/V Mute Timer
setting in the projector's ECO menu.
• If the projector's lamp turns off unexpectedly, the lens cover timer may be
enabled. To turn off the lens cover timer, select Off as the Lens Cover
Timer setting in the projector's ECO menu.
192
• If the projector's lamp turns off, the status indicator is flashing, and the
temp (temperature) indicator is lit, the projector has overheated and turned
off.
• If the power button on the remote control does not turn on the projector,
check its batteries and make sure at least one of the remote receivers are
available in the Remote Receiver setting in the projector's Settings menu.
• The cooling fans may run in standby status depending on the projector
settings. Also, when the projector wakes from standby status, the fans may
cause an unexpected noise. This is not a malfunction.
g Related Links
• "Projector Setup Settings - ECO Menu" p.159
• "Projector Indicator Status" p.183
• "Projector Feature Settings - Settings Menu" p.145
• "Unlocking the Projector's Buttons" p.98
Solutions to Problems with the Remote Control
If the projector does not respond to remote control commands, try the
following solutions:
• Check that the remote control batteries are installed correctly and have
power. If necessary, replace the batteries.
• Make sure you are operating the remote control within the reception angle
and range of the projector.
• Make sure the projector is not warming up or shutting down.
• Check to see if a button on the remote control is stuck down, causing it to
enter sleep mode. Release the button to wake the remote control up.
• Strong fluorescent lighting, direct sunlight, or infrared device signals may be
interfering with the projector's remote receivers. Dim the lights or move the
projector away from the sun or interfering equipment.
• Make sure at least one of the remote receivers are available in the Remote
Receiver setting in the projector's Settings menu.
• If the Remote Receiver setting is disabled, hold down the [Menu] button on
the remote control for at least 15 seconds to reset the setting to its default.
Solving Projector or Remote Control Operation Problems
• If you assigned an ID number to the projector to operate multiple projectors
from the remote control, you may need to check or change the ID setting.
• If you lose the remote control, you can order another one from Epson.
g Related Links
• "Remote Control Operation" p.33
• "Projector Feature Settings - Settings Menu" p.145
• "Selecting the Projector You want to Operate" p.90
• "Replacing the Remote Control Batteries" p.180
Solutions to Password Problems
If you cannot enter or remember a password, try the following solutions:
• You may have turned on password protection without first setting a
password. Try entering 0000 using the remote control.
• If you have entered an incorrect password too many times and see a
message displaying a request code, write down the code and contact Epson
for help. Provide the request code and proof of ownership for assistance in
unlocking the projector.
• If you lose the remote control you cannot enter a password. Order a new
one from Epson.
Solution When "The Battery that Saves Your Clock
Settings is Running Low" Message Appears
If the message "The battery that saves your clock settings is running low." is
displayed, contact Epson for help.
Solutions to Gesture Presenter Problems
If the Gesture Presenter feature does not work correctly, try the following
solutions:
193
• Check the USB cable is securely connected to the computer and the
projector.
• Select Normal as the Power Consumption setting.
s ECO > Power Consumption
• Dim the room lights. Make sure the projection surface is not in direct
sunlight or other sources of bright lighting.
• Check the brightness of the room is stable.
• Make sure you project images onto a white surface. If the projection surface
is not white, the gesture presenter feature may not work correctly.
Solving Network Problems
Check the solutions in these sections if you have problems using the projector
on a network.
g Related Links
• "Solutions When Wireless Authentication Fails" p.194
• "Solutions When You Cannot Access the Projector Through the Web" p.194
• "Solutions When Network Alert E-Mails are not Received" p.194
• "Solutions When the Image Contains Static During Network Projection"
p.195
• "Solutions When You Cannot Connect Using Screen Mirroring" p.195
• "Solutions When the Image or Sound Contains Static During Screen
Mirroring Connection" p.195
Solutions When Wireless Authentication Fails
If you are having trouble with the authentication, try the following solutions
(EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB-2165W/EB-2155W/EB2065/EB-2055/EB-X550KG/EB-X500KG):
• If the wireless settings are correct, but authentication fails, you may need to
update the Date & Time settings on the projector's Extended menu.
s Extended > Operation > Date & Time
• Check the Security settings in the projector's Network menu.
s Network > Network Configuration > Wireless LAN
g Related Links
• "Projector Setup Settings - Extended Menu" p.147
• "Network Menu - Wireless LAN Menu" p.153
Solutions When You Cannot Access the Projector
Through the Web
If you are unable to access the projector through a Web browser, make sure
you are using the correct ID and password.
194
• When accessing Basic Control in Epson Web Control, enter
EPSONREMOTE as the user ID. (You cannot change the user ID.)
• Enter the password set in the projector's Network menu as the Basic
Control password. The default password is guest.
s Network > Network Configuration > Basic > Remote Password
• When accessing Advanced in Epson Web Control, enter EPSONWEB as
the user ID. (You cannot change the user ID.)
• Enter the password set in the projector's Network menu as the Advanced or
OSD Control Pad password. The default password is admin.
s Network > Network Configuration > Basic > Web Control Password
• Make sure you have access to the network the projector is on.
• If your Web browser is set up to connect via a proxy server, the Web
Control screen cannot be displayed. Make settings for a connection without
using a proxy server.
a
The user ID and password are case sensitive.
g Related Links
• "Network Menu - Basic Menu" p.152
Solutions When Network Alert E-Mails are not
Received
If you do not receive an e-mail alerting you to problems with a projector over
the network, try the following solutions:
• Make sure the projector is turned on and connected to the network
correctly. (If an error shuts down the projector, the email may not be
delivered.)
• Make sure you set up the projector e-mail alert settings correctly on the
projector's network Notifications menu or in the network software.
Solving Network Problems
• Set the Standby Mode setting to Communication On in the projector's
ECO menu so the network software can monitor the projector in standby
mode.
• Make sure your electrical outlet or power source is functioning correctly.
g Related Links
• "Network Menu - Notifications Menu" p.156
Solutions When the Image Contains Static During
Network Projection
If the projected image contains static during network projection, try the
following solutions:
• Check for any obstacles between the access point, the computer, the mobile
device, and the projector, and change their positions to improve
communication.
• Make sure that the access point, the computer, the mobile device and the
projector are not too far apart. Move them closer together and try to
connect again.
• If the wireless connection is slow or your projected image contains noise,
check for interference from other equipment, such as a Bluetooth device or
microwave. Move the interfering device farther away or expand your
wireless bandwidth.
• Reduce the number of connected devices if the connection speed declines.
Solutions When You Cannot Connect Using Screen
Mirroring
If you are unable to connect to the projector using Screen Mirroring, try the
following solutions (EB-2265U/EB-2255U/EB-2165W):
• Check the projector's settings.
195
• Select On as the Screen Mirroring setting in the projector's Network
menu.
• Change the Display Name so that it does not include "-" in the projector's
Screen Mirroring Settings setting menu or it may not be displayed
correctly on your mobile device.
s Network > Screen Mirroring Settings > Display Name
• Select Off as the Screen Mirroring setting in the projector's Network
menu, and select On again.
• Change the Operation Mode and connect again.
s Network > Screen Mirroring Settings > Operation Mode
• Make sure that the no other devices are connected to the projector with
No Interruptions settings.
s Network > Screen Mirroring Settings > Extended > Meeting Mode
• Change the Channel settings according to the wireless LAN environment.
s Network > Screen Mirroring Settings > Extended > Channel
• Check the mobile device's settings.
• Make sure the settings on the mobile device are correct.
• When connecting again immediately after disconnecting, it may take
some time until the connection is established. Reconnect after waiting for
a while.
• Restart the mobile device.
• Once you have connected using Screen Mirroring, the projector
connection information may be recorded on the mobile device. However,
you may not be able to reconnect to the projector from the recorded
information. Select the projector from the list of available devices.
g Related Links
• "Projector Network Settings - Network Menu" p.150
• "Network Menu - Screen Mirroring Settings" p.151
Solutions When the Image or Sound Contains Static
During Screen Mirroring Connection
If the projected image or sound contains static when connecting using Screen
Mirroring, try the following solutions (EB-2265U/EB-2255U/EB-2165W):
Solving Network Problems
• Avoid covering the Wi-Fi antenna of the mobile device.
• If you use a Screen Mirroring connection and an internet connection at the
same time, the image may stop or contain noise. Disconnect the internet
connection to expand your wireless bandwidth and improve the connection
speed of the mobile device.
• Make sure the projection contents meet the Screen Mirroring requirements.
• Depending on the settings of the mobile device, the connection may be lost
when the device enters power saving mode. Check the electrical power
saving settings on the mobile device.
• Update to the latest version of the wireless driver or firmware on the mobile
device.
g Related Links
• "Wireless Network Projection from a Mobile Device (Screen Mirroring)"
p.113
196
Appendix
Check these sections for the technical specifications and important notices about your projector.
g Related Links
• "Optional Accessories and Replacement Parts" p.198
• "Screen Size and Projection Distance" p.200
• "Supported Monitor Display Resolutions" p.204
• "Projector Specifications" p.206
• "External Dimensions" p.209
• "USB Display System Requirements" p.210
• "List of Safety Symbols (corresponding to IEC60950-1 A2)" p.211
• "Glossary" p.213
• "Notices" p.215
Optional Accessories and Replacement Parts
The following optional accessories and replacement parts are available. Please
purchase these products as and when needed.
The following list of optional accessories and replacement parts is current as
of: August 2016.
Details of accessories are subject to change without notice and availability
may vary depending on the country of purchase.
g Related Links
• "Screens" p.198
• "Cables" p.198
• "Mounts" p.198
• "For Wireless Connection" p.198
• "External Devices" p.199
• "Replacement Parts" p.199
198
Cables
Computer cable ELPKC02 (1.8 m - for mini D-sub 15-pin/mini D-Sub
15pin)
Computer cable ELPKC09 (3 m - for mini D-sub 15-pin/mini D-Sub
15pin)
Computer cable ELPKC10 (20 m - for mini D-sub 15-pin/mini D-Sub
15pin)
Use when connecting to the Computer port.
Component video cable ELPKC19 (3 m - for mini D-Sub 15-pin/RCA male
x 3)
Use this to connect a component video source.
Mounts
Screens
60" portable screen ELPSC27
80" portable screen ELPSC28
100" portable screen ELPSC29
Portable roll-type screens. (aspect ratio 4:3)
70" portable screen ELPSC23
80" portable screen ELPSC24
90" portable screen ELPSC25
Portable roll-type screens. (aspect ratio 16:10)
Multi Aspect Screen ELPSC26/ELPSC26H
Portable multi-aspect screen.
Ceiling mount ELPMB23
Use when installing the projector on a ceiling.
Ceiling pipe (450 mm) ELPFP13
Ceiling pipe (700 mm) ELPFP14
Use when installing the projector on a high ceiling.
a
Special expertise is required to suspend the projector from a ceiling.
Contact Epson for help.
For Wireless Connection
Wireless LAN module ELPAP10
Use this to project images from a computer via a wireless communication.
(Frequency band: 2.4GHz)
Optional Accessories and Replacement Parts
External Devices
Document Camera ELPDC21
Use when projecting image such as books, OHP documents, or slides.
Soft carrying case ELPKS68
Use this to carry the projector by hand.
External Speaker ELPSP02
External self-powered speaker.
Interface box ELPCB02
When the projector is suspended from a ceiling, install the remote control
to operate the projector by hand.
HDBaseT Transmitter ELPHD01 (EB-2265U/EB-2165W)
Use when sending an HDMI or RS-232C signal over a long distance.
(HDCP 2.2 is not supported)
Replacement Parts
Lamp unit ELPLP95 (EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EB-X500KG)
Lamp unit ELPLP87 (EB-2140W/EB-2040)
Use as a replacement for used lamps.
Air filter ELPAF41
Use as a replacement for used air filters.
199
Screen Size and Projection Distance
200
Check the table here to determine how far to place the projector from the
screen based on the size of the projected image.
16:10 screen size
A
B
Minimum (Wide) to
Maximum (Tele)
40"
86 × 54
116 - 194
-5
50"
108 × 67
146 - 243
-6
60"
129 × 81
176 - 293
-7
80"
172 × 108
236 - 392
-10
100"
215 × 135
296 - 491
-12
150"
323 × 202
446 - 738
-18
200"
431 × 269
595 - 985
-24
300"
646 × 404
895 - 1479
-37
A
B
4:3 screen size
Minimum (Wide) to
Maximum (Tele)
A Projection distance (cm)
B Distance from the center of the lens to the base of the screen (or to the top of
the screen, if suspended from a ceiling) (cm)
C Center of lens
WUXGA (EB-2265U/EB-2255U/EB-2250U)/WXGA (EB-2165W)
16:10 screen size
A
B
Minimum (Wide) to
Maximum (Tele)
30"
65 × 40
86 - 145
-4
35"
75 × 47
101 - 169
-4
30"
61 × 46
98 - 164
-4
40"
81 × 61
132 - 220
-6
50"
102 × 76
166 - 276
-7
60"
122 × 91
200 - 332
-8
70"
142 × 107
234 - 388
-10
80"
163 × 122
268 - 444
-11
100"
203 × 152
335 - 556
-14
150"
305 × 229
505 - 836
-21
200"
406 × 305
674 - 1115
-28
260"
528 × 396
878 - 1451
-36
Screen Size and Projection Distance
16:9 screen size
A
201
16:10 screen size
B
Minimum (Wide) to
Maximum (Tele)
A
B
Minimum (Wide) to
Maximum (Tele)
30"
66 × 37
89 - 149
-2
200"
431 × 269
683 - 1117
-10
35"
77 × 44
104 - 174
-2
260"
560 × 350
889 - 1453
-13
40"
89 × 50
119 - 200
-2
50"
111 × 62
150 - 250
-3
A
B
60"
133 × 75
181 - 301
-3
70"
155 × 87
212 - 352
-4
80"
177 × 100
243 - 403
-4
100"
221 × 125
304 - 504
-6
150"
332 × 187
458 - 758
-8
200"
443 × 249
612 - 1012
-11
290"
642 × 361
889 - 1469
-16
EB-2265U/EB-2255U/EB-2250U do not support screen sizes smaller
than 50".
a
4:3 screen size
Minimum (Wide) to
Maximum (Tele)
40"
81 × 61
152 - 250
-2
50"
102 × 76
191 - 314
-3
60"
122 × 91
230 - 377
-3
70"
142 × 107
269 - 441
-4
80"
163 × 122
308 - 504
-4
100"
203 × 152
385 - 631
-5
150"
305 × 229
580 - 948
-8
200"
406 × 305
774 - 1265
-11
220"
447 × 335
852 - 1391
-12
A
B
WUXGA (EB-2245U)
16:10 screen size
16:9 screen size
A
B
Minimum (Wide) to
Maximum (Tele)
45"
97 × 61
151 - 249
-2
50"
108 × 67
168 - 277
-2
60"
129 × 81
203 - 333
-3
70"
151 × 94
237 - 389
-3
80"
172 × 108
271 - 445
-4
100"
215 × 135
340 - 557
-5
150"
323 × 202
512 - 837
-7
Minimum (Wide) to
Maximum (Tele)
45"
100 × 56
155 - 256
1
50"
111 × 62
173 - 285
1
60"
133 × 75
208 - 342
1
70"
155 × 87
244 - 400
1
80"
177 × 100
279 - 457
2
100"
221 × 125
350 - 572
2
150"
332 × 187
526 - 860
3
Screen Size and Projection Distance
16:9 screen size
A
202
4:3 screen size
B
Minimum (Wide) to
Maximum (Tele)
A
B
Minimum (Wide) to
Maximum (Tele)
200"
443 × 249
703 - 1148
4
100"
203 × 152
340 - 553
-4
250"
553 × 311
879 - 1436
5
120"
244 × 183
408 - 664
-5
150"
305 × 229
511 - 831
-6
200"
406 × 305
682 - 1108
-8
250"
508 × 381
854 - 1386
-10
A
B
WXGA (EB-2155W/EB-2140W)
16:10 screen size
A
B
Minimum (Wide) to
Maximum (Tele)
16:9 screen size
30"
65 × 40
88 - 144
-1
40"
86 × 54
118 - 193
-1
50"
108 × 67
149 - 243
-2
60"
129 × 81
179 - 292
-2
80"
172 × 108
239 - 390
-3
100"
215 × 135
300 - 488
-3
150"
323 × 202
451 - 733
-5
200"
431 × 269
603 - 979
-7
250"
538 × 337
754 - 1224
-8
280"
603 × 377
845 - 1371
-9
A
B
4:3 screen size
Minimum (Wide) to
Maximum (Tele)
Minimum (Wide) to
Maximum (Tele)
30"
66 × 37
91 - 149
1
40"
50 × 89
122 - 199
1
50"
111 × 62
153 - 249
2
60"
133 × 75
184 - 300
2
80"
177 × 100
246 - 401
3
100"
221 × 125
308 - 502
3
150"
332 × 187
464 - 754
5
200"
443 × 249
619 - 1006
7
250"
553 × 311
775 - 1258
9
275"
609 × 342
853 - 1384
10
XGA (EB-2065/EB-2055/EB-2040/EB-X550KG/EB-X500KG)
30"
61 × 46
100 - 164
-1
40"
81 × 61
134 - 219
-2
50"
102 × 76
169 - 275
-2
60"
122 × 91
203 - 331
-2
30"
61 × 46
83 - 136
-5
80"
163 × 122
271 - 442
-3
40"
81 × 61
111 - 182
-6
4:3 screen size
A
B
Minimum (Wide) to
Maximum (Tele)
Screen Size and Projection Distance
4:3 screen size
A
203
16:10 screen size
B
Minimum (Wide) to
Maximum (Tele)
A
B
Minimum (Wide) to
Maximum (Tele)
50"
102 × 76
140 - 229
-8
30"
65 × 40
88 - 144
-1
60"
122 × 91
169 - 275
-10
40"
86 × 54
118 - 193
-1
80"
163 × 122
226 - 368
-13
50"
108 × 67
149 - 243
-2
100"
203 × 152
283 - 460
-16
60"
129 × 81
179 - 292
-2
150"
305 × 229
426 - 692
-24
70"
151 × 94
209 - 341
-2
200"
406 × 305
568 - 923
-32
80"
172 × 108
239 - 390
-3
250"
508 × 381
711 - 1155
-40
100"
215 × 135
300 - 488
-3
300"
610 × 457
854 - 1386
-48
150"
323 × 202
451 - 733
-5
200"
431 × 269
603 - 979
-7
250"
538 × 337
754 - 1224
-8
280"
603 × 377
845 - 1371
-9
16:9 screen size
A
B
Minimum (Wide) to
Maximum (Tele)
30"
66 × 37
91 - 149
1
40"
50 × 89
122 - 199
1
50"
111 × 62
153 - 249
2
60"
133 × 75
184 - 300
2
80"
177 × 100
246 - 401
3
100"
221 × 125
308 - 502
3
150"
332 × 187
464 - 754
5
200"
443 × 249
619 - 1006
7
250"
553 × 311
775 - 1258
9
275"
609 × 342
853 - 1384
10
Supported Monitor Display Resolutions
The table here lists the compatible refresh rate and resolution for each
compatible video display format.
Component Signals (Analog RGB)
204
Component Video
Signal
Refresh rate (Hz)
Resolution (dots)
SDTV (480i/480p)
60
720 × 480
Signal
Refresh rate (Hz)
Resolution (dots)
SDTV (576i/576p)
50
720 × 576
VGA
60/72/75/85
640 × 480
HDTV (720p)
50/60
1280 × 720
SVGA
60/72/75/85
800 × 600
HDTV (1080i)
50/60
1920 × 1080
XGA
60/70/75/85
1024 × 768
WXGA
60
1280 × 768
60
1366 × 768
60/75/85
1280 × 800
Signal
Refresh rate (Hz)
Resolution (dots)
WXGA+
60/75/85
1440 × 900
TV (NTSC)
60
720 × 480
WXGA++
60
1600 × 900
TV (SECAM)
50
720 × 576
SXGA
70/75/85
1152 × 864
TV (PAL)
50/60
720 × 576
60/75/85
1280 × 960
60/75/85
1280 × 1024
SXGA+
60/75
1400 × 1050
WSXGA+ *
60
1680 × 1050
UXGA
60
1600 × 1200
WUXGA **
60
1920 × 1280
* WSXGA+ is available only for EB-2265U/EB-2255U/EB-2250U/EB2245U/EB-2165W/EB-2155W/EB-2140W and compatible only when Wide is
selected as the Resolution setting in the projector's Signal menu.
** WUXGA is available only for EB-2265U/EB-2255U/EB-2250U/EB-2245U.
Even when signals other than those mentioned above are input, it is likely that
the image can be projected. However, not all functions may be supported.
Composite Video
HDMI and HDBaseT * Port Input Signals
Signal
Refresh rate (Hz)
Resolution (dots)
VGA
60
640 × 480
SVGA
60
800 × 600
XGA
60
1024 × 768
WXGA
60
1280 × 800
60
1366 × 768
WXGA+
60
1440 × 900
WXGA++
60
1600 × 900
UXGA
60
1600 × 1200
WSXGA+ **
60
1680 × 1050
SXGA
60
1280 × 960
60
1280 × 1024
60
1400 × 1050
SXGA+
Supported Monitor Display Resolutions
Signal
Refresh rate (Hz)
Resolution (dots)
WUXGA ***
60
1920 × 1200
SDTV (480i/480p)
60
720 × 480
SDTV (576i/576p)
50
720 × 576
HDTV (720p)
50/60
1280 × 720
HDTV (1080i)
50/60
1920 × 1080
HDTV (1080p)
24/30/50/60
1920 × 1080
* Only when an HDMI connection is made using the optional HDBaseT
Transmitter for EB-2265U/EB-2165W.
** WSXGA+ is available only for EB-2265U/EB-2255U/EB-2250U/EB2245U/EB-2165W/EB-2155W/EB-2140W.
*** WUXGA is available only for EB-2265U/EB-2255U/EB-2250U/EB-2245U.
MHL Input Signal
Signal
Refresh rate (Hz)
Resolution (dots)
VGA
60
640 × 480
SDTV (480i/480p)
60
720 × 480
SDTV (576i/576p)
50
720 × 576
HDTV (720p)
50/60
1280 × 720
HDTV (1080i)
50/60
1920 × 1080
HDTV (1080p)
24/30
1920 × 1080
205
Projector Specifications
Product name
EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB-2165W/EB2155W/EB-2140W/EB-2065/EB-2055/EB-2040/EBX550KG/EB-X500KG
Dimensions
EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB-2165W:
377 (W) × 110 (H) × 291 (D) mm (not including raised
section)
EB-2155W/EB-2140W/EB-2065/EB-2055/EB-2040/EBX550KG/EB-X500KG:
377 (W) × 101 (H) × 291 (D) mm (not including raised
section)
206
Lamp
EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB2165W/EB-2155W/EB-2065/EB-2055/EB-X550KG/EBX500KG:
UHE lamp, 300 W Model No.: ELPLP95
EB-2140W/EB-2040:
UHE lamp, 215 W Model No.: ELPLP87
Lamp life
Normal Power Consumption mode: Up to 5,000 hours
ECO Power Consumption mode: Up to 10,000 hours
Max. audio output
16W
EB-2265U/EB-2255U/EB-2250U/EB-2165W:
0.76"
EB-2245U:
0.67"
EB-2155W/EB-2140W:
0.59"
EB-2065/EB-2055/EB-2040/EB-X550KG/EB-X500KG:
0.63"
Speaker
1
Power supply
EB-2265U/EB-2165W/EB-2065/EB-X550KG:
100-240V AC±10% 50/60Hz 4.5 - 2.0 A
EB-2255U/EB-2250U/EB-2245U/EB-2155W/EB-2055/EBX500KG:
100-240V AC±10% 50/60Hz 4.3 - 1.9 A
EB-2140W/EB-2040:
100-240V AC±10% 50/60Hz 3.4 - 1.5 A
Display method
Poly-silicon TFT active matrix
Resolution
EB-2265U/EB-2255U/EB-2250U/EB-2245U:
2,304,000 pixels
WUXGA (1920 (W) × 1200 (H) dots) × 3
EB-2165W/EB-2155W/EB-2140W:
1,024,000 pixels
WXGA (1280 (W) × 800 (H) dots) × 3
EB-2065/EB-2055/EB-2040/EB-X550KG/EB-X500KG:
786,432 pixels
XGA (1024 (W) × 768 (H) dots) × 3
Power consumption
(100 to 120 V area)
EB-2265U/EB-2165W/EB-2065/EB-X550KG:
Operating: 450 W
Standby power consumption (Communication On): 2.40 W
Standby power consumption (Communication Off): 0.21 W
LCD panel size
Focus adjustment
Manual
Zoom adjustment
1-1.6
EB-2255U/EB-2250U/EB-2245U/EB-2155W/EB-2055/EBX500KG:
Operating: 429 W
Standby power consumption (Communication On): 2.40 W
Standby power consumption (Communication Off): 0.21 W
EB-2140W/EB-2040:
Operating: 333 W
Standby power consumption (Communication On): 2.40 W
Standby power consumption (Communication Off): 0.21 W
Projector Specifications
Power consumption
(220 to 240 V area)
EB-2265U/EB-2165W/EB-2065/EB-X550KG:
Operating: 425 W
Standby power consumption (Communication On): 2.41 W
Standby power consumption (Communication Off): 0.31 W
EB-2255U/EB-2250U/EB-2245U/EB-2155W/EB-2055/EBX500KG:
Operating: 405 W
Standby power consumption (Communication On): 2.41 W
Standby power consumption (Communication Off): 0.31 W
EB-2140W/EB-2040:
Operating: 316 W
Standby power consumption (Communication On): 2.41 W
Standby power consumption (Communication Off): 0.31 W
Operating altitude
Altitude 0 to 3,048 m
Operating
temperature
+5 to +40°C (No condensation) (Altitude 0 to 2,286 m)
+5 to +35°C (No condensation) (Altitude more than 2,286
m)
Storage temperature
-10 to +60°C (No condensation)
Mass
EB-2265U/EB-2255U:
Approx. 4.7 kg
EB-2250U/EB-2245U/EB-2165W:
Approx. 4.6 kg
EB-2155W/EB-2055/EB-X500KG:
Approx. 4.3 kg
EB-2140W/EB-2040:
Approx. 4.2 kg
EB-2065/EB-X550KG:
Approx. 4.4 kg
This product is also designed for IT power distribution system with phase-tophase voltage 230V.
207
Angle of tilt
If you use the projector tilted at an angle of more than 30˚ it could be
damaged and cause an accident.
g Related Links
• "Connector Specifications" p.207
Connector Specifications
Computer1 port
1
Mini D-Sub15-pin (female)
Computer2/Monitor Out
port
1
Mini D-Sub15-pin (female)
Video port
1
RCA pin jack
Audio 1 port
1
Stereo mini pin jack
Audio 2 port
1
Stereo mini pin jack
L-Audio-R ports
1
RCA pin jack x 2 (L-R)
Audio Out port
1
Stereo mini pin jack
HDMI1/MHL port
1
HDMI (Audio is only supported by
PCM)
HDMI2 port
1
HDMI (Audio is only supported by
PCM)
USB-A port
1
USB connector (Type A)
USB-B port
1
USB connector (Type B)
Projector Specifications
USB port (for Wireless
1
LAN module)
(EB-2265U/EB-2255U/EB2250U/EB-2245U/EB2165W/EB-2155W/EB2065/EB-2055/EBX550KG/EB-X500KG)
USB connector (Type A)
LAN port
1
RJ-45
HDBaseT port
(EB-2265U/EB-2165W)
1
RJ-45
RS-232C port
1
Mini D-Sub 9-pin (male)
a
• USB-A and USB-B port supports USB 2.0. However, USB ports are
not guaranteed to operate all devices that support USB.
• USB-B port is not support USB 1.1.
208
External Dimensions
209
EB-2265U/EB-2255U/EB-2250U/EB-2245U/EB-2165W
EB-2155W/EB-2140W/EB-2065/EB-2055/EB-2040/EB-X550KG/EBX500KG
The unit in these illustrations is mm.
A Center of lens
B Distance from center of lens to suspension bracket fixing point
USB Display System Requirements
To use the projector's Epson USB Display software, your computer must meet
the following system requirements.
Requirement
Windows
Operating system Windows Vista
• Ultimate (32-bit)
• Enterprise (32-bit)
• Business (32-bit)
• Home Premium (32-bit)
• Home Basic (32-bit)
Windows 7
• Ultimate (32- and 64-bit)
• Enterprise (32- and 64-bit)
• Professional (32- and 64-bit)
• Home Premium (32- and 64bit)
• Home Basic (32-bit)
• Starter (32-bit)
Windows 8
• Windows 8 (32- and 64-bit)
• Windows 8 Pro (32- and 64bit)
• Windows 8 Enterprise (32and 64-bit)
Windows 8.1
• Windows 8.1 (32- and 64-bit)
• Windows 8.1 Pro (32- and 64bit)
• Windows 8.1 Enterprise (32and 64-bit)
210
Requirement
Mac
Windows 10
• Windows 10 Home (32- and
64-bit)
• Windows 10 Pro (32- and 64bit)
• Windows 10 Enterprise (32and 64-bit)
Mac
OS X
• 10.7.x (32- and 64-bit)
• 10.8.x (64-bit)
• 10.9.x (64-bit)
• 10.10.x (64-bit)
• 10.11.x (64-bit)
Windows
CPU
Intel Core2Duo or faster
(Intel Core i3 or faster
recommended)
Memory
2GB or more
(4GB or more recommended)
Hard disk space
20 MB or more
Display
Resolution between 640 × 480 and 1920 × 1200
16-bit color or greater
a
Intel Core2Duo or faster
(Intel Core i5 or faster
recommended)
Operation is not guaranteed for Windows Vista without any service
packs installed, or Windows Vista Service Pack 1.
List of Safety Symbols (corresponding to IEC60950-1 A2)
The following table lists the meaning of the safety symbols labeled on the
equipment.
No. Symbol mark
Approved
standards
Description
A
IEC60417
No.5007
"ON" (power)
To indicate connection to the mains.
B
IEC60417
No.5008
"OFF" (power)
To indicate disconnection from the
mains.
C
IEC60417
No.5009
Stand-by
To identify the switch or switch
position by means of which part of the
equipment is switched on in order to
bring it into the stand-by condition.
D
ISO7000
No.0434B,
IEC3864-B3.1
Caution
To identify general caution when
using the product.
E
IEC60417
No.5041
Caution, hot surface
To indicate that the marked item can
be hot and should not be touched
without taking care.
IEC60417
No.6042
ISO3864-B3.6
Caution, risk of electric shock
To identify equipment that has risk of
electric shock.
G
IEC60417
No.5957
For indoor use only
To identify electrical equipment
designed primarily for indoor use.
H
IEC60417
No.5926
Polarity of d.c. power connector
To identify the positive and negative
connections (the polarity) on a piece
of equipment to which a d.c. power
supply may be connected.
F
211
No. Symbol mark
Approved
standards
Description
I
—
The same as No.8.
J
IEC60417
No.5001B
Battery, general
On battery powered equipment. To
identify a device for instance a cover
for the battery compartment, or the
connector terminals.
K
IEC60417
No.5002
Positioning of cell
To identify the battery holder itself
and to identify the positioning of the
cell(s) inside the battery holder.
L
—
The same as No.11.
M
IEC60417
No.5019
Protective earth
To identify any terminal which is
intended for connection to an external
conductor for protection against
electric shock in case of a fault, or the
terminal of a protective earth
electrode.
N
IEC60417
No.5017
Earth
To identify an earth (ground) terminal
in cases where neither the symbol
No.13 is explicitly required.
O
IEC60417
No.5032
Alternating current
To indicate on the rating plate that the
equipment is suitable for alternating
current only; to identify relevant
terminals.
P
IEC60417
No.5031
Direct current
To indicate on the rating plate that the
equipment is suitable for direct
current only; to identify relevant
terminals.
List of Safety Symbols (corresponding to IEC60950-1 A2)
No. Symbol mark
Approved
standards
Description
Q
IEC60417
No.5172
Class II equipment
To identify equipment meeting the
safety requirements specified for Class
II equipment according to IEC 61140.
R
ISO 3864
General prohibition
To identify actions or operations that
are prohibited.
S
ISO 3864
Contact prohibition
To indicate injury that could occur
due to touching a specific part of the
equipment.
T
—
Never look into the optical lens while
the projector is on.
U
—
To indicate that the marked item don’t
place anything on projector.
V
ISO3864
IEC60825-1
Caution, laser radiation
To indicate the equipment has a laser
radiation part.
W
ISO 3864
Disassembly prohibition
To indicate a risk of injury, such as
electric shock, if the equipment is
disassembled.
X
IEC60417
No. 5266
Standby, partial standby
To indicate that part of the equipment
is in the ready status.
Y
ISO3864
IEC60417
No. 5057
Caution, movable parts
To indicate that you must keep away
from movable parts according to
protection standards.
212
Glossary
213
This section briefly explains the difficult terms that are not explained in the
text of this guide. For details, refer to other commercially available
publications.
AMX Device
Discovery
Aspect Ratio
AMX Device Discovery is a technology developed by AMX to
facilitate AMX control systems for easy operation of the target
equipment.
Epson have implemented this protocol technology, and have
provided a setting to enable the protocol function (ON).
See the AMX Web site for more details.
URL http://www.amx.com/
The ratio between an image's length and its height.
Screens with a horizontal:vertical ratio of 16:9, such as HDTV
screens, are known as wide screens.
SDTV and general computer displays have an aspect ratio of
4:3.
Component Video A method that separates the video signal into a luminance
component (Y), and a blue minus luminance (Cb or Pb) and a
red minus luminance (Cr or Pr).
Composite Video
A method that combines the video signal into a luminance
component and a color component for transmission down a
single cable.
Contrast
The relative brightness of the light and dark areas of an image
can be increased or decreased to make text and graphics stand
out more clearly, or to make them appear softer. Adjusting this
particular property of an image is called contrast adjustment.
DHCP
An abbreviation of Dynamic Host Configuration Protocol, this
protocol automatically assigns an IP address to equipment
connected to a network.
DICOM
An acronym for Digital Imaging and Communications in
Medicine.
An international standard that defines image standards and a
communications protocol for medical images.
Gateway Address
This is a server (router) for communicating across a network
(subnet) divided according to subnet mask.
HDCP
HDCP is an abbreviation for High-bandwidth Digital Content
Protection.
It is used to prevent illegal copying and protect copyrights by
encrypting digital signals sent over DVI and HDMI ports.
Because the HDMI port on this projector supports HDCP, it
can project digital images protected by HDCP technology.
However, the projector may not be able to project images
protected with updated or revised versions of HDCP
encryption.
HDMI™
An abbreviation for High Definition Multimedia Interface.
HDMI™ is a standard aimed at digital consumer electronics and
computers. This is the standard by which HD images and
multichannel audio signals are digitally transmitted.
By not compressing the digital signal, the image can be
transferred at the highest quality possible. It also provides an
encryption function for the digital signal.
HDTV
An abbreviation for High-Definition Television that refers to
high-definition systems which satisfy the following conditions:
• Vertical resolution of 720p or 1080i or greater (p =
Progressive, i = Interlace)
• Screen aspect ratio of 16:9
Infrastructure
mode
A method for wireless LAN connection in which devices
communicate through access points.
Interlace
Transmits information needed to create one screen by sending
every other line, starting from the top of the image and working
down to the bottom.
Images are more likely to flicker because one frame is displayed
every other line.
IP Address
A number to identify a computer connected to a network.
MHL
An abbreviation for Mobile High-definition Link, a standard
for connection interfaces aimed at mobile devices such as
smartphones and tablets.
Images can be transferred at high quality and at high speeds
without compressing the digital signal, and also charges
connected devices.
Glossary
214
Progressive
Projects information to create one screen at a time, displaying
the image for one frame.
Even though the number of scan lines is the same, the amount
of flicker in images decreases because the volume of
information has doubled compared with an interlace system.
Refresh Rate
The light-emitting element of a display maintains the same
luminosity and color for an extremely short time.
Because of this, the image must be scanned many times per
second to refresh the light-emitting element.
The number of refresh operations per second is called the
Refresh rate and is expressed in hertz (Hz).
SDTV
An abbreviation for Standard Definition Television that refers
to standard television systems which do not satisfy the
conditions for HDTV High-Definition Television.
SNMP
An abbreviation for Simple Network Management Protocol,
which is the protocol for monitoring and controlling devices
such as routers and computers connected to a TCP/IP network.
sRGB
SSID
An international standard for color intervals that was
formulated so that colors that are reproduced by video
equipment can be handled easily by computer operating
systems (OS) and the Internet. If the connected source has an
sRGB mode, set both the projector and the connected signal
source to sRGB.
SSID is identification data for connecting to another device on
a wireless LAN. Wireless communication is possible between
devices with the same SSID.
Subnet Mask
This is a numerical value that defines the number of bits used
for the network address on a divided network (subnet) from the
IP address.
SVGA
A screen size standard with a resolution of 800 (horizontal) ×
600 (vertical) dots.
SXGA
A screen size standard with a resolution of 1,280 (horizontal) ×
1,024 (vertical) dots.
Sync.
The signals output from computers have a specific frequency.
If the projector frequency does not match this frequency, the
resulting images are not of a good quality.
The process of matching the phases of these signals (the relative
position of the crests and the troughs in the signal) is called
Synchronization.
If the signals are not synchronized, flickering, blurriness, and
horizontal interference occur.
Tracking
The signals output from computers have a specific frequency.
If the projector frequency does not match this frequency, the
resulting images are not of a good quality.
The process of matching the frequency of these signals (the
number of crests in the signal) is called Tracking.
If Tracking is not carried out correctly, wide vertical stripes
appear in the signal.
Trap IP Address
This is the IP address for the destination computer used for
error notification in SNMP.
VGA
A screen size standard with a resolution of 640 (horizontal) ×
480 (vertical) dots.
XGA
A screen size standard with a resolution of 1,024 (horizontal) ×
768 (vertical) dots.
WXGA
A screen size standard with a resolution of 1,280 (horizontal) ×
800 (vertical) dots.
WUXGA
A screen size standard with a resolution of 1,920 (horizontal) ×
1,200 (vertical) dots.
Notices
215
Check these sections for important notices about your projector.
Type of Product: LCD Projector
g Related Links
• "FCC Compliance Statement" p.215
• "Indication of the manufacturer and the importer in accordance with
requirements of EU directive" p.216
• "Wireless Telegraphy Act Regulations" p.216
• "Restriction of Use" p.216
• "Operating System References" p.216
• "Trademarks" p.216
• "Copyright Notice" p.217
• "Copyright Attribution" p.217
Model:
H814C/H815C/H816C/H817C/H818C/H819C/H820C/H821C/H822C/H835
C/H836C/H871C/H872C
FCC Compliance Statement
DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B Personal Computers
We: Epson America, Inc.
FCC Compliance Statement For United States Users
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause interference to radio and television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Located at: 3840 Kilroy Airport Way MS: 3-13 Long Beach, CA 90806
WARNING
Tel: 562-981-3840
The connection of a non-shielded equipment interface cable to this
equipment will invalidate the FCC Certification or Declaration of this device
and may cause interference levels which exceed the limits established by the
FCC for this equipment. It is the responsibility of the user to obtain and use a
shielded equipment interface cable with this device. If this equipment has
more than one interface connector, do not leave cables connected to unused
interfaces. Changes or modifications not expressly approved by the
manufacturer could void the user's authority to operate the equipment.
Declare under sole responsibility that the product identified herein, complies
with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each
product marketed, is identical to the representative unit tested and found to
be compliant with the standards. Records maintained continue to reflect the
equipment being produced can be expected to be within the variation
accepted, due to quantity production and testing on a statistical basis as
required by 47CFR 2.909. Operation is subject to the following two
conditions : (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
Trade Name: EPSON
Statement for Canadian EMC Rules
Notices
Indication of the manufacturer and the importer in
accordance with requirements of EU directive
Manufacturer: SEIKO EPSON CORPORATION
Address: 3-5, Owa 3-chome, Suwa-shi, Nagano-ken 392-8502 Japan
Telephone: 81-266-52-3131
http://www.epson.com/
Importer: EPSON EUROPE B.V.
Address: Atlas Arena, Asia Building, Hoogoorddreef 5,1101 BA Amsterdam
Zuidoost
The Netherlands
Telephone: 31-20-314-5000
http://www.epson.com/europe.html
Wireless Telegraphy Act Regulations
The following acts are prohibited by the Wireless Telegraphy Act.
• Modifying and disassembling (including the antenna)
• Removing the label of conformance
• Using the 5 GHz Wireless LAN usage outdoors
Restriction of Use
When this product is used for applications requiring high reliability/safety
such as transportation devices related to aviation, rail, marine, automotive
etc.; disaster prevention devices; various safety devices etc; or
functional/precision devices etc, you should use this product only after giving
consideration to including fail-safes and redundancies into your design to
maintain safety and total system reliability. Because this product was not
intended for use in applications requiring extremely high reliability/safety
such as aerospace equipment, main communication equipment, nuclear
216
power control equipment, or medical equipment related to direct medical care
etc, please make your own judgment on this product’s suitability after a full
evaluation.
Operating System References
•
•
•
•
•
Microsoft® Windows Vista® operating system
Microsoft® Windows® 7 operating system
Microsoft® Windows® 8 operating system
Microsoft® Windows® 8.1 operating system
Microsoft® Windows® 10 operating system
In this guide, the operating systems above are referred to as "Windows Vista",
"Windows 7", "Windows 8", "Windows 8.1", and "Windows 10". Furthermore,
the collective term "Windows" is used to refer to them all.
•
•
•
•
•
OS X 10.7.x
OS X 10.8.x
OS X 10.9.x
OS X 10.10.x
OS X 10.11.x
In this guide, the operating systems above are referred to as "OS X 10.7.x", "OS
X 10.8.x", "OS X 10.9.x", "OS X 10.10.x", and "OS X 10.11.x". Furthermore, the
collective term "OS X" is used to refer to them all.
Trademarks
EPSON is a registered trademark, EXCEED YOUR VISION, ELPLP and their
logos are registered trademarks or trademarks of Seiko Epson Corporation.
Mac, Mac OS, and OS X, are trademarks of Apple Inc.
Microsoft, Windows, Windows Vista, PowerPoint, and the Windows logo are
trademarks or registered trademarks of Microsoft Corporation in the United
States and/or other countries.
Notices
WPA™, WPA2™, and Wi-Fi Protected Setup™ are registered trademarks of Wi-Fi
Alliance.
App Store is a service mark of Apple Inc.
Google play is a trademark of Google Inc.
HDMI and High-Definition Multimedia Interface are the trademarks or
registered trademarks of HDMI Licensing LLC.
MHL, the MHL logo, and Mobile High-Definition Link are the trademarks or
registered trademarks of MHL and LLC in the United States and/or other
countries.
"QR Code" is a registered trademark of DENSO WAVE INCORPORATED.
PJLink trademark is a trademark applied for registration or is already
registered in Japan, the United States of America and other countries and
areas.
Foxit PDF SDK Copyright ©2011, Foxit Software Company
www.foxitsoftware.com, All rights reserved.
Crestron® and Crestron RoomView® are registered trademarks of Crestron
Electronics, Inc.
Intel® is a registered trademark of Intel Corporation in the U.S. and/or other
countries.
Miracast™ is the trademark of the Wi-Fi Alliance.
Extron® and XTP® are registered trademarks of Extron Electronics.
HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT
Alliance.
Other product names used herein are also for identification purposes only
and may be trademarks of their respective owners. Epson disclaims any and
all rights in those marks.
Copyright Notice
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior written
217
permission of Seiko Epson Corporation. No patent liability is assumed with
respect to the use of the information contained herein. Neither is any liability
assumed for damages resulting from the use of the information contained
herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the
purchaser of this product or third parties for damages, losses, costs, or
expenses incurred by the purchaser or third parties as a result of: accident,
misuse, or abuse of this product or unauthorized modifications, repairs, or
alterations to this product, or (excluding the U.S.) failure to strictly comply
with Seiko Epson Corporation's operating and maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems
arising from the use of any options or any consumable products other than
those designated as Original Epson Products or Epson Approved Products by
Seiko Epson Corporation.
The contents of this guide may be changed or updated without further notice.
Illustrations in this guide and the actual projector may differ.
Copyright Attribution
This information is subject to change without notice.
©SEIKO EPSON CORPORATION 2016. All rights reserved.
2016.8 413287200EN
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising