60131 2PGS

Add to my manuals
2 Pages

advertisement

60131 2PGS | Manualzz
 J ANDORF ¥.1//4 Make-A-Lamp Kit
Make-A-Lamp Kit #60131 Project Overview
(with Bottle Adapter)
1 — 8" SPT-1 Lamp Cord (18 Gauge) with polarized plug - White (0)
1 — Push Through Socket (Rated: 660W-250V) - Brass Finish (C)
3 — 3 Sizes of Bottle Adapters (K)
1 — Lamp Nipple (J)
1 — Check Ring (1)
1 — Lock Nut (N)
<— Finial (A)
<—— Lamp Harp (B)
What's Its Purpose
(L) Sleeves —— —>
Create your own lamp.
Tools Needed
- 7)
Screwdriver (M) Underwriter's Knot >Q Z
Wire Stripper 4A— Socket Cap (F),
Zh Socket Screw (G) |
Other Items Harp Bottom (H)
You Might Need <— Check Ring (1)
Finial <—— Ni
Bottle or Vase Nipple (J)
Bottle Adapter (K)
WARNING
e Before beginning TURN OFF POWER (N) Lock nut ——
by unplugging lamp from wall outlet.
e Follow local electrical regulations or (0) Lamp Cord —>
codes when installing and using
this product.
e Deviation from the assembly
instructions may result in a risk of
fire or electric shock.
e Light bulbs generate heat —
maintain manufacter’s recommended
space between shade and bulb.
www.Jandorf.com 60 Meadow Lane, Northfield, Ohio 44067 @Jandorf 2010 lllustration represents typical components, lamps may vary.
11/14 Make-A-Lamp Kit
EN
GANDORF
© HARDWARE e PLUMBING e ELECTRICAL
« Measure Opening ©
Г
©
4
<—N
Before beginning TURN OFF POWER by unplugging Select bottle with solidly structured, secure base. At other end of nipple, thread lock nut (N) until flush
lamp from wall outlet. Choose adapter (K) to fit bottle opening. Screw with adapter.
nipple (J) so 1/4" of nipple sticks out from adapter.
Ov
With lock nut end facing down, push adapter into Slide harp bottom (H)* over lamp nipple (J). Remove socket cap from socket shell and loosen
bottle opening so that 1/4" nipple extends from socket screw (1). Thread socket cap (F) onto lamp
bottle. Slide check ring (I) over nipple to cover nipple and tighten. Tighten socket screw (G).
opening. Cardboard insulation disc should be firmly in bottom
of socket cap.
brass
terminal
silver SCIewW
terminal
Screw
neutral
Feed cord through bottom or side of lamp, up Using wire stripper, expose 2" of bare copper Connect ribbed neutral wire (feel outside of cord for
through nipple and out socket cap (F). Split cord strands from cord. Twist copper strands tightly ribbing) around silver terminal screw and smooth
about 2" from end and tie an Underwriter’s together. wire around brass terminal screw.
Knot (M).
A>
NE,
silver
terminal cardboard
insulating
sleeve
Wrap each wire clockwise 3/4 turn under head of Make sure cardboard lining is firmly in place in Insert top of harp (B) into harp bottom (H) and slide
terminal screw. Tighten screws. Cut loose strands. socketshell (D). Place socket shell on cap (F). Pull sleeves (L) to lock in place®. Insert bulb, shade and
extra wire back through lamp. Snap socket shell (D) finial (A).
into socket cap by gently rocking side-to-side, until
shell snaps into place with clicking sound.
* Harp is optional.
www.Jandorf.com 60 Meadow Lane, Northfield, Ohio 44067 — Evandorf 2010 Illustration represents typical components, lamps may vary.
JIJI SI IIIIIIIIIIJIIIJA

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement