Vented Subwoofer Enclosure System
S in gle , 10 "/ 12"/ 15"
V e nt ed S ub w o o f er
E nclo su re Syst em
MODEL
CO104SBSV-4
CO124SBSV-4
CO154SBSV-4
CO104SBDVC-2
CO124SBDVC-2
CO154SBDVC-2
OWNER'S MANUAL
Introduction
thank you for your purchase of the orion vented subwoofer enclosure system from
MD Audio Engineering. the orion vented subwoofer enclosure system will excite and
delight the auto sound enthusiast with years of high quality audio reproduction.
orion vented subwoofer enclosure systems are covered by a limited warranty. Be sure
to retain your original sales receipt, and refer to the warranty section on the back
cover of this guide for full details about your coverage.
Practice Safe Sound™
High-powered car audio systems may produce sound pressure levels that
exceed the threshold at which hearing loss may result. they may also impair a
driver’s ability to hear traffic sounds or emergency vehicles. use common sense
and practice safe listening habits when listening to or adjusting your audio
system. If your subwoofer enclosure is installed in the passenger compartment, make sure
it is restrained from moving in case of an accident.
Your Product Information
model number:
Date of Purchase:
Installation
1.
Place the speaker assembly in your vehicle. common placement will normally be
the trunk, back seat, or back of a van.
2.
connect each speaker to an amplifier output (not supplied), observing that the
polarity markings on the back of the speaker enclosure are connected to the
corresponding polarities on the amplifier.
NOTES:
•
Do not use an amplifier that can drive the speakers beyond their specifications.
•
leave at least three inches of clear space in front of the port(s) and woofer(s) to
allow for adequate air flow and woofer movement without obstruction. orienting
the woofers toward the rear of the vehicle will in most instances enhance the bass
performance.
WARNING: loose objects can become projectiles in the event of a rapid
deceleration, abrupt turn or accident. Secure the enclosure in place with the
mounting brackets provided to prevent it from shifting.
© 2012 MD Audio Engineering—All rights
1
4 Ohm Enclosure Wire Connection Guide
the following diagram shows a standard connection to a mono amplifier or single
channel of a multi-channel amplifier.
NOTE: refer to your amplifier owner’s manual before connecting the subwoofer
enclosure system.
STANDARD AMPLIFIER
CONNECTION
Subwoofer Enclosure System
+
-
Amplifier
4 ohm
load
+
-
Specifications
feature
frequency response
Power handling (rms)
Power handling peak
Box Impedance
Efficiency (1W/1m)
Woofer size (inches)
number of woofers
Enclosure type
typical output level @ full power
CO104SBSV-4
35 Hz – 250 Hz
350 watts x 1
700 watts x 1
4 ohms x 1
86 dB
10”
1
slot vented
117 to 126 dB
CO124SBSV-4
25 Hz – 250 Hz
350 watts x 1
700 watts x 1
4 ohms x 1
88 dB
12”
1
slot vented
119 to 128 dB
CO154SBSV-4
22 Hz – 250 Hz
550 watts x 1
1100 watts x 1
4 ohms x 1
91 dB
15”
1
slot vented
122 to 131 dB
Depth x Width x Height (inches)
Weight
17.5" x 14.2" x 13.8"
29.76 lb (13.5 kg)
17.8" x 16.5" x 15.4"
33.73 lb (15.3 kg)
20.5" x 19.5" x 19"
47.4 lb (21.5 kg)
2
© 2012 MD Audio Engineering—All rights
2 Ohm Enclosure Wire Connection Guide
the following diagram shows a standard connection to a mono amplifier or single
channel of a multi-channel amplifier.
NOTE: refer to your amplifier owner’s manual before connecting the subwoofer
enclosure system.
STANDARD AMPLIFIER
CONNECTION
Subwoofer Enclosure System
+
-
Amplifier
2 ohm
load
+
-
Specifications
feature
frequency response
Power handling (rms)
Power handling peak
Box Impedance
CO104SBDVC-2
35 Hz – 250 Hz
400 watts x 1
800 watts x 1
2 ohms x 1
CO124SBDVC-2
25 Hz – 250 Hz
400 watts x 1
800 watts x 1
2 ohms x 1
CO154SBDVC-2
22 Hz – 250 Hz
600 watts x 1
1200 watts x 1
2 ohms x 1
Efficiency (1W/1m)
Woofer size (inches)
number of woofers
Enclosure type
typical output level @ full power
Depth x Width x Height (inches)
Weight
86 dB
10”
1
slot vented
118 to 127 dB
17.5" x 14.2" x 13.8"
29.76 lb (13.5 kg)
88 dB
12”
1
slot vented
120 to 129 dB
17.8" x 16.5" x 15.4"
33.73 lb (15.3 kg)
91 dB
15”
1
slot vented
123 to 132 dB
20.5" x 19.5" x 18.9"
47.4 lb (21.5 kg)
© 2012 MD Audio Engineering—All rights
3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising