Logix5000 Control Systems:Connecting PowerFlex 525 Drives Over

Logix5000 Control Systems:Connecting PowerFlex 525 Drives Over
Quick Start
Logix5000 Control Systems: Connect PowerFlex 525 Drives
over an EtherNet/IP Network
Catalog Numbers Logix5000 Controllers, PowerFlex 525 Drives
Important User Information
Solid-state equipment has operational characteristics differing from those of electromechanical equipment. Safety
Guidelines for the Application, Installation and Maintenance of Solid State Controls (publication SGI-1.1 available from
your local Rockwell Automation sales office or online at http://www.rockwellautomation.com/literature/) describes some
important differences between solid-state equipment and hard-wired electromechanical devices. Because of this difference,
and also because of the wide variety of uses for solid-state equipment, all persons responsible for applying this equipment
must satisfy themselves that each intended application of this equipment is acceptable.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the
use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and
requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or
liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or
software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation,
Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment,
which may lead to personal injury or death, property damage, or economic loss.
ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property
damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.
SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous
voltage may be present.
BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may
reach dangerous temperatures.
IMPORTANT
Identifies information that is critical for successful application and understanding of the product.
Allen-Bradley, CompactLogix, ControlLogix, Integrated Architecture, Logix5000, PowerFlex, Rockwell Software, Rockwell Automation, RSLogix, RSLinx, Stratix 6000, Studio 5000, and TechConnect are trademarks of
Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Table of Contents
Preface
About This Publication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Before Using This Publication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Controller and Other Component Quick Starts . . . . . . . . . . . . . . . . . . . . . . 7
Use Each Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Where to Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
How Hardware is Connected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Required Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Chapter 1
Prepare the PowerFlex 525 Drive
Hardware
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What You Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Follow These Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mount the Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Install Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configure the Embedded EtherNet/IP Adapter . . . . . . . . . . . . . . . . . . . .
Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11
11
12
13
13
16
18
Chapter 2
Add a PowerFlex 525 Drive to a
Controller Project
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What You Need . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Follow These Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Add the Drive to the Controller Project . . . . . . . . . . . . . . . . . . . . . . . . . . .
Download the Project and Connect to the Drive. . . . . . . . . . . . . . . . . . . .
Edit the Drive Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test the PowerFlex 525 Drive Tags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
19
20
21
25
26
28
30
Index
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
3
Table of Contents
4
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
Preface
About This Publication
This quick start provides examples and procedures for including a PowerFlex® 525 drive in a Logix5000™ control
system over an EtherNet/IP network. The programming examples are not complex, and offer easy solutions to
verify that devices are communicating and functioning properly.
IMPORTANT
This publication describes example tasks you complete when using a PowerFlex 525 drive on an EtherNet/IP network.
The tasks described are not the only tasks you can complete with the PowerFlex 525 drive on an EtherNet/IP network.
Before Using This Publication
You can complete the tasks described in this publication only after first completing some prerequisite tasks with a
Logix5000 controller. For example, before you can add a PowerFlex 525 drive to an RSLogix™ 5000 or Studio
5000™ Logix Designer application project, as described on page 19, you must first create the project in a
Logix5000 controller.
Table 1 describes the tasks you must complete before using this publication.
IMPORTANT
The example graphics shown in the table are for CompactLogix™ 5370 L3 controllers. Depending on the Logix5000
controller you are using, the specific steps to complete the tasks described in the table can vary.
Table 1 - Required Tasks to Complete before Using This Quick Start
Task
Description
Prepare the Logix5000
control system
hardware
Assembling the control system and connecting to communication networks. Some components, for example, the
Logix5000 controller and system power supply, are required. Other components, for example, a network communication
module, are optional.
These example graphics show the assembly of one Logix5000 controller.
1 (Front)
2 (Rear)
IMPORTANT
This task does not include installation of specific hardware components, for example,
PowerFlex 525 drives, used over the networks included in your application.
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
5
Preface
Table 1 - Required Tasks to Complete before Using This Quick Start (continued)
6
Task
Description
Prepare the computer
Installing the necessary software on your computer, for example, RSLogix 5000 software or Logix Designer application.
Configure the networks
Completing required tasks associated with the networks used in your application, such as assigning an IP address to the
controller’s communication port or communication module in your Logix5000 control system.
Create a controller
project
Creating a project used with and stored in your Logix5000 controller that includes all desired control system components
and necessary programming, for example, adding ladder logic to test tasks associated with individual system components.
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
Preface
Controller and Other Component Quick Starts
This quick start describes how to use one device on one network in a Logix5000 control system. Typically,
though, a Logix5000 control system includes more than the controller and one device on one network.
For example, if a Logix5000 control system operates on an EtherNet/IP network, in addition to a controller,
power supply, and communication modules, the system can use remote I/O modules, drives, and graphic
terminals.
Other quick starts describe how to use different devices on different networks in Logix5000 control systems. For
more information, see the Integrated Architecture™: Logix5000 Control Systems Quick Starts Quick Reference,
publication IASIMP-QR024.
Use Each Chapter
The beginning of each chapter contains the following sections of information that must be read before you begin
working in the chapter:
• Before You Begin - This section lists the tasks you must complete before starting the chapter.
• What You Need - This section lists the components that are required to complete the tasks in the chapter.
• Follow These Steps - This section illustrates the steps in the current chapter.
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
7
Preface
Where to Start
Prerequisite Tasks:
Described in Before Using
This Publication on page 5.
Logix5000
Controller
Esc
Sel
Prepare the PowerFlex 525 Drive
Hardware on page 11
PowerFlex 525
Drive
Add a PowerFlex 525 Drive to a
Controller Project on page 19
8
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
Preface
How Hardware is Connected
This quick start demonstrates the following possible control system.
Computer
Logix5000 Controller
with Ethernet
Connection
PowerFlex 525 Drive
via Embedded
EtherNet/IP Adapter
Esc
Sel
Stratix 6000™
Managed Switch
8 7
6 5
4 3
2 1
Required Software
To complete examples in this quick start, you need the software described in this table.
Software
Required Version
Required for This Task
RSLogix 5000
20.00.00 or later(1)
Create or change RSLogix 5000 projects to use PowerFlex 525 drive
Studio 5000 Logix Designer
21.00.00 or later
Create or change the Studio 5000 Logix Designer project to use
PowerFlex 525 drive
BOOTP/DHCP utility
Version automatically installed with RSLogix Set IP address for PowerFlex 525 drive
5000 software and varies according to that
software’s version
OR
(1) RSLogix 5000 software, version 20.00.00 or later, is required for use of this quick start because the example Logix5000 controller, and associated tasks, described herein are completed in a CompactLogix
5370 control system. CompactLogix 5370 control systems require RSLogix 5000 software, version 20.00.00 or later. If you connect a PowerFlex 525 drive over an EtherNet/IP network in a Logix5000 control
system that uses a different controller, the minimum version can differ.
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
9
Preface
Parts List
You need these parts to complete the tasks described in this quick start.
✓
Quantity
Cat. No.
Description
1
25B-xyyyN1z4
PowerFlex 525 AC drive
1
1585J-M8PBJM-2
RJ45 to RJ45 Ethernet cable
For a list of parts required to complete the prerequisite tasks listed in Table 1 on page 5, see the documentation
describing those tasks.
Additional Resources
Use the resources listed in this table for more information when using PowerFlex 525 drives over an EtherNet/IP
network in a Logix5000 controller project.
Resource
Description
PowerFlex 525 Adjustable Frequency AC Drive User Manual,
publication 520-UM001
Provides basic information needed to install, start up, program, and troubleshoot
the PowerFlex 525 AC drive.
EtherNet/IP Modules in Logix5000 Control Systems,
publication ENET-UM001
Describes how to install, configure, and operate EtherNet/IP modules.
ControlLogix® Controllers Common Procedures Programming Provides details about adding and configuring modules, establishing
communication, and writing ladder logic.
Manual, publication 1756-PM001
Industrial Automation Wiring and Grounding Guidelines,
publication 1770-4.1
Provides general guidelines for installing a Rockwell Automation® industrial system.
Product Certifications website, http://www.ab.com
Provides declarations of conformity, certificates, and other certification details.
You can view or download publications at http://www.rockwellautomation.com/literature. To order paper
copies of technical documentation, contact your local Allen-Bradley distributor or Rockwell Automation sales
representative.
10
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
Chapter 1
Prepare the PowerFlex 525 Drive Hardware
In this chapter, you learn how to complete the following tasks:
• Mount and wire power to a PowerFlex 525 AC drive.
• Configure EtherNet/IP communication for the drive.
Before You Begin
You must complete these tasks before using this chapter:
• The tasks described in Before Using This Publication on page 5.
The example controller project used in this chapter uses a CompactLogix 5370 L3 controller.
What You Need
This table lists the products you need to complete the tasks described in this chapter.
Quantity
Cat. No.
Description
1
25B-xyyyN1z4
PowerFlex 525 AC drive
1
1585J-M8PBJM-2
RJ45 to RJ45 Ethernet cable
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
11
Chapter 1
Prepare the PowerFlex 525 Drive Hardware
Follow These Steps
Mount the Drive on page 13
Esc
Sel
Esc
Sel
Install Power Wiring on page 13
L1/R L2/S L3/T T1/U T2/V T3/W
DC- DC+ BRBR+
Configure the Embedded
EtherNet/IP Adapter on page 16
12
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
Prepare the PowerFlex 525 Drive Hardware
Chapter 1
Mount the Drive
The PowerFlex 525 drive must be mounted on a flat, vertical, and level surface (or DIN rail), following the
requirements for minimum clearances, ambient operating temperature, and debris protection. For complete
mounting instructions, see the PowerFlex 525 Adjustable Frequency AC Drive User Manual, publication
520-UM001.
Install Power Wiring
Follow these steps to access the power terminals and connect the power wires.
ATTENTION: Verify that all incoming power is turned off before connecting power wires to the drive.
1. Access the power terminal block:
• For frames B…E drives, press
in and hold down the latches
on both sides of the power
terminal cover and pull out
and swing upwards to remove
the cover.
Press Side Latches in and Pull
Cover Up and Off of Drive
Power Terminal Cover
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
13
Chapter 1
Prepare the PowerFlex 525 Drive Hardware
• For frame A dives, press down and pull out on the top cover of the control module, then hold the sides
and pull the control module out of the power module.
Press Down on Tab and
Pull Out on Cover
Power Module
Control Module
Hold Sides of Control
Module and Pull Out
2. Press and hold down the locking tab on the terminal guard, and slide the terminal guard down to remove
from the power module.
Slide Terminal
Guard Down
Press and
Hold Down
Locking Tab
14
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
Prepare the PowerFlex 525 Drive Hardware
3. Connect the AC power conductors to
the drive terminals as described in the
following table and tighten the screws
according to the torque specifications
listed in the drive user manual.
Terminal
L1/R, L2/S, L3/T
T1/U, T2/V, T3/W
DC+, DCBR+, BR-
Description
AC input line connections
Motor connections
DC bus connections
Dynamic brake resistor connections
Safety ground - PE connection
Chapter 1
Frames A, B, C, and D
L1/R L2/S L3/T T1/U T2/V T3/W
DC- DC+ BRBR+
Frame E
L1/R
L2/S
L3/T
For complete information on wiring a
PowerFlex 525 drive, see the PowerFlex
525 Adjustable Frequency AC Drives
User Manual, publication 520-UM001.
T1/U
T2/V
DC-
T3/W
DC+
BR+
BR-
4. Replace all covers.
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
15
Chapter 1
Prepare the PowerFlex 525 Drive Hardware
Configure the Embedded EtherNet/IP Adapter
The PowerFlex 525 Embedded EtherNet/IP network adapter requires a network IP address to operate on an
EtherNet/IP network. There are two methods for configuring the embedded EtherNet/IP adapter IP address:
• BOOTP Server – Use BOOTP if you prefer to control the IP addresses of devices with a server. The IP
address, subnet mask, and gateway addresses are provided by the BOOTP server. BOOTP is enabled by
default.
• Adapter Parameters – Use adapter parameters when you want more flexibility in setting up the IP address,
or need to communicate outside of the control network with a gateway. The IP address, subnet mask, and
gateway addresses then come from the adapter parameters you set.
IMPORTANT
If you are setting your network addresses manually with parameters, you must set C128 [EN Addr Sel] to 1
‘Parameters’.
IMPORTANT
Regardless of the method used to set the adapter IP address, each node on the EtherNet/IP network must have a
unique IP address. To change an IP address, you must set the new value and then remove and reapply power to
(or reset) the adapter.
Follow these steps to configure the Embedded EtherNet/IP adapter with the BOOTP/DHCP utility.
1. Remove the control module
cover by pressing and holding
down the arrow on the front of
the cover and slide the cover
down and off of the drive.
2. Connect one end of an Ethernet
cable to the Embedded Ethernet
adapter port in the drive, routing
the cable through the opening in
the bottom of the control
module.
3. Connect the other end of the
cable to the system’s Ethernet
switch.
Connect
Ethernet
Cable
Press and Hold Down Arrow
on Front and Pull Cover
Down and Off of Drive
4. Apply power to the drive.
5. Start the BOOTP/DHCP utility.
16
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
Prepare the PowerFlex 525 Drive Hardware
Chapter 1
6. From the Tools menu, choose Network
Settings.
7. Type the Subnet Mask of the network.
The Gateway address, Primary and/or
Secondary DNS address, and Domain
Name fields are optional.
8. Click OK.
The Request History panel appears with the hardware addresses of all devices issuing BOOTP requests.
9. Select the appropriate device, that is, the
device with the MAC ID that matches
your PowerFlex 525 drive.
10. Click Add to Relation List.
The New Entry dialog box appears.
11. Type an IP Address, Hostname, and
Description for the adapter.
12. Click OK.
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
17
Chapter 1
Prepare the PowerFlex 525 Drive Hardware
13. To permanently assign this
configuration to the adapter,
wait for the adapter to appear
in the Relation List panel and
select it.
14. Click Disable BOOTP/DHCP.
When power is cycled, the adapter uses the assigned configuration and does not issue a BOOTP request.
IMPORTANT
If you do not click Disable BOOTP/DHCP, on a power cycle, the host controller clears the current IP configuration
and begins sending BOOTP requests again.
Additional Resources
For a list of additional resources that can assist you when preparing the PowerFlex 525 drive hardware, see
page 10.
18
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
Chapter 2
Add a PowerFlex 525 Drive to a Controller Project
In this chapter, you add a PowerFlex 525 drive to a controller project and configure the drive. You also download
the project to the controller so you can verify communication with the drive.
Before You Begin
You must complete these tasks before using this chapter:
• The tasks described in Before Using This Publication on page 5.
• Prepare the PowerFlex 525 drive as described in Chapter 1, Prepare the PowerFlex 525 Drive Hardware on
page 11.
What You Need
You need RSLogix 5000 software or the Studio 5000 Logix Designer application to complete the tasks described
in this chapter.
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
19
Chapter 2
Add a PowerFlex 525 Drive to a Controller Project
Follow These Steps
Add the Drive to the Controller
Project on page 21
Download the Project and
Connect to the Drive on page 25
Edit the Drive Parameters
on page 26
Test the PowerFlex 525 Drive
Tags on page 28
20
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
Add a PowerFlex 525 Drive to a Controller Project
Chapter 2
Add the Drive to the Controller Project
IMPORTANT
The tasks described in this section use a RSLogix 5000 project for a CompactLogix 5370 L3 controller. CompactLogix 5370 L3
controllers require that you use RSLogix 5000 software, version 20.00.00 or later. The Studio 5000 Logix Designer application
version 21.00 or later can also be used. The steps are very similar to the RSLogix 5000 project shown in this section.
If you are using a different Logix5000 controller, your project’s RSLogix 5000 software version requirement can be different.
1. Verify that your controller project is
offline and the Logix5000 controller is
in PROG mode.
RUN
REM
PROG
2. Right-click your network port and
choose New Module.
The Select Module Type dialog box appears. Note that the Select Module Type dialog box can appear
differently depending on which Logix5000 controller your application uses and, thus, what version of
controller software is used.
3. Select the PowerFlex 525-EENET
drive module.
4. Check Close on Create at the bottom
of the dialog box.
5. Click Create.
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
21
Chapter 2
Add a PowerFlex 525 Drive to a Controller Project
The Module Properties dialog box for the drive appears.
6. Type a Name for the drive.
7. Type the same IP address for the drive as
the IP address you assigned to the
EtherNet/IP adapter in Configure the
Embedded EtherNet/IP Adapter on
page 16.
8. Click Change.
The Module Definition dialog box appears.
9. In the Module Definition dialog box,
complete the following tasks.
a. From the Drive Rating pull-down
menu, choose the rating for your
PowerFlex 525 drive.
b. From the Electronic Keying pulldown menu, choose Disable Keying.
c. Click OK.
A message box appears to indicate that the module data types and properties will be changed due to these
selections.
10. Click Yes.
22
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
Add a PowerFlex 525 Drive to a Controller Project
Chapter 2
11. Click the Drive tab.
12. From the device toolbar, click Upload.
A Connection Browser appears.
13. Navigate to and select the desired drive.
14. Click OK.
If you have not previously connected to a
PowerFlex 525 drive, a Creating Device
Database File dialog box appears and
shows the progress of the database
creation. No action is necessary.
IMPORTANT
If your computer already has a
database, the software does not
create a new one.
A Connecting dialog box appears and
shows the progress of the connection.
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
23
Chapter 2
Add a PowerFlex 525 Drive to a Controller Project
When the connection is complete, the Upload dialog box appears.
15. Click Upload Entire Device.
An Upload dialog box appears and
shows the progress of the upload.
If there are any differences between the
drive in your project and the drive to
which you are connecting, a Module
Definition Differences Found dialog
box appears and shows the differences. If
this is the drive you want to add to your
project, click OK. Otherwise, click
Cancel and repeat step 12 through step
15.
16. When the Module Definition dialog box
appears, click OK.
The PowerFlex 525 is added to the
controller organizer under the network
port.
17. Save the project.
24
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
Add a PowerFlex 525 Drive to a Controller Project
Chapter 2
Download the Project and Connect to the Drive
1. Click the Controller Status icon and
choose Download.
The Download Warning dialog box appears.
2. Click Download.
The controller project goes online with
the controller and the project is
downloaded.
Once the project has successfully
downloaded to the controller, if the
Module Properties window for the drive
is open, a connection is made with the
drive.
IMPORTANT
If a fault message appears on your
PowerFlex 525 drive, press
on the keypad to clear the fault.
3. Put the controller in REM mode and
change the controller project to Remote
Run mode.
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
25
Chapter 2
Add a PowerFlex 525 Drive to a Controller Project
Edit the Drive Parameters
1. If necessary, open the Module Properties
dialog box for the drive and, on the Drive
tab, click Parameters in the toolbar.
The Parameter List dialog box appears.
2. To change drive parameters, click the
Value column cell for the appropriate
parameter and make a change.
Depending on the Value cell, choose the
appropriate value from pull-down menu
or type your value.
26
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
Add a PowerFlex 525 Drive to a Controller Project
Chapter 2
3. Change the parameters listed in the following table to values shown.
Parameter
Name
Value
Parameter 40
Autotune
Ready/Idle
Parameter 47
Speed Reference1
EtherNet/IP
Parameter 62
DigIn TermBlk 02
Not Used
Parameter 63
DigIn TermBlk 03
Not Used
Parameter 64
2-Wire Mode
Edge Trigger
Parameter 65
DigIn TermBlk 05
Not Used
Parameter 66
DigIn TermBlk 06
Not Used
Parameter 67
DigIn TermBlk 07
Not Used
Parameter 68
DigIn TermBlk 08
Not Used
Parameter 153
EN Data In 1
0
Parameter 154
EN Data In 2
0
Parameter 155
EN Data In 3
0
Parameter 156
EN Data In 4
0
Parameter 157
EN Data Out 1
0
Parameter 158
EN Data Out 2
0
Parameter 159
EN Data Out 3
0
Parameter 160
EN Data Out 4
0
4. Close the Parameter List dialog box.
The parameters are saved in the drive.
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
27
Chapter 2
Add a PowerFlex 525 Drive to a Controller Project
Test the PowerFlex 525 Drive Tags
1. Put the controller in RUN mode.
RUN
REM
PROG
2. Double-click Controller Tags.
3. On the Monitor Tags tab, expand the
PowerFlex 525 drive output tag and
change the ClearFaults tag to 1 to clear
any initial faults.
4. Change the ClearFaults tag back to 0.
5. Expand the PowerFlex 525 drive input
tag and verify that the Ready tag value is
1.
This tag indicates that the drive is ready
to start.
28
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
Add a PowerFlex 525 Drive to a Controller Project
Chapter 2
6. In the drive output tags, change the
CommandedFreq tag to 15000
engineering units (this is approximately
59.5 Hz).
WARNING: If there is a motor attached to your drive, completing the next step causes the motor to turn.
7. Change the Start tag to 1.
The display on the drive registers the
speed increase in Hz until the value
entered at the reference tag is reached.
8. Change the Start tag back to 0.
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
29
Chapter 2
Add a PowerFlex 525 Drive to a Controller Project
9. Change the Stop tag to 1.
The display on the drive shows a speed
decrease until the drive reaches 0.00 Hz.
10. Change the Stop tag back to 0.
11. Go Offline.
By starting and stopping the drive, you verified the following conditions exist in your application:
• The controller is correctly communicating with the drive.
• The drive can receive and execute simple commands.
Additional Resources
For a list of additional resources that can assist you when adding the drive to a controller project, see page 10.
30
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
Index
B
BOOTP/DHCP utility 9, 16-18
C
connections
hardware 9
D
drive parameters
edit in RSLogix 5000 software 26-27
edit in Studio 5000 environment 26-27
drive preparation
mount 13
wire power 13
drive tags
test in RSLogix 5000 software 28-30
test in Studio 5000 environment 28-30
E
environment
Studio 5000 9, 21-30
Ethernet adapter
assign IP address 16-18
H
Q
quick starts
for devices in Logix5000 control systems 7
R
requirements
hardware preparation 11
parts 11
prerequisite tasks 5-6
software 9
RSLogix 5000 software
add drive to project 19-30
edit drive parameters 26-27
requirements 9
test drive tags 28-30
S
set IP address
BOOTP/DHCP utility 16-18
software
BOOTP/DHCP utility 9, 16-18
RSLogix 5000 9, 21-30
Studio 5000 environment
add drive to project 19-30
edit drive parameters 26-27
requirements 9
test drive tags 28-30
hardware
example control system 9
mount drive 13
preparation 11
wire power 13
I
IP address
assign to drive 22
assign to Ethernet adapter 16-18
L
Logix5000 controllers
prerequisite tasks 5-6
M
mode switch 21, 28
P
parts
required to complete tasks 10
power
connect to drive 13
prerequisite tasks 5-6
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
31
Index
32
Rockwell Automation Publication IASIMP-QS036A-EN-P - April 2013
Rockwell Automation Support
Rockwell Automation provides technical information on the Web to assist you in using its products.
At http://www.rockwellautomation.com/support/, you can find technical manuals, a knowledge base of FAQs, technical and
application notes, sample code and links to software service packs, and a MySupport feature that you can customize to
make the best use of these tools.
For an additional level of technical phone support for installation, configuration, and troubleshooting, we offer
TechConnectSM support programs. For more information, contact your local distributor or Rockwell Automation
representative, or visit http://www.rockwellautomation.com/support/.
Installation Assistance
If you experience a problem within the first 24 hours of installation, review the information that is contained in this
manual. You can contact Customer Support for initial help in getting your product up and running.
United States or Canada
1.440.646.3434
Outside United States or Canada
Use the Worldwide Locator at http://www.rockwellautomation.com/support/americas/phone_en.html, or contact your local Rockwell
Automation representative.
New Product Satisfaction Return
Rockwell Automation tests all of its products to ensure that they are fully operational when shipped from the
manufacturing facility. However, if your product is not functioning and needs to be returned, follow these procedures.
United States
Contact your distributor. You must provide a Customer Support case number (call the phone number above to obtain one) to your
distributor to complete the return process.
Outside United States
Please contact your local Rockwell Automation representative for the return procedure.
Documentation Feedback
Your comments will help us serve your documentation needs better. If you have any suggestions on how to improve this
document, complete this form, publication RA-DU002, available at http://www.rockwellautomation.com/literature/.
Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400
www.rockwel lautomation.com
Power, Control and Information Solutions Headquarters
Americas: Rockwell Automation, 1201 South Second Street, Milwaukee, WI 53204-2496 USA, Tel: (1) 414.382.2000, Fax: (1) 414.382.4444
Europe/Middle East/Africa: Rockwell Automation NV, Pegasus Park, De Kleetlaan 12a, 1831 Diegem, Belgium, Tel: (32) 2 663 0600, Fax: (32) 2 663 0640
Asia Pacific: Rockwell Automation, Level 14, Core F, Cyberport 3, 100 Cyberport Road, Hong Kong, Tel: (852) 2887 4788, Fax: (852) 2508 1846
Publication IASIMP-QS036A-EN-P - April 2013
Copyright © 2013 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising