I-7531 User Manual

I-7531 User Manual
The I-7531 CAN Repeater
User’s Manual
Warranty
All products manufactured by ICP DAS are under
warranty regarding defective materials for a period of one
year from the date of delivery to the original purchaser.
Warning
ICP DAS assumes no liability for damages resulting
from the use of this product. ICP DAS reserves the right to
change this manual at any time without notice. The
information furnished by ICP DAS is believed to be
accurate and reliable. However, no responsibility is
assumed by ICP DAS for its use, or for any infringements
of patents or other rights of third parties resulting from its
use.
Copyright
Copyright 1997 by ICP DAS. All rights are reserved.
Trademark
The names used for identification only may be
registered trademarks of their respective companies.
I-7531 CAN Repeater User Manual (ver. 1.4, 2008/07/11) ------1
1 Tables of Content
1
2
Tables of Content....................................................................................2
Introduction.............................................................................................3
2.1
2.2
3
4
5
Features..........................................................................................4
Specifications.................................................................................4
2.3 Application .....................................................................................4
Technical data .........................................................................................5
3.1
3.2
Block Diagram................................................................................5
Appearance ....................................................................................6
3.3
3.4
Pin Assignment..............................................................................7
Wire Connection ............................................................................9
3.5 Status LED....................................................................................10
3.6 Terminator Resistor Setting........................................................10
3.7 Cable Selection ............................................................................12
3.8 Driving Capability and Baud Rate ..............................................13
Application Architecture ......................................................................15
Dimension and Mounting .....................................................................16
I-7531 CAN Repeater User Manual (ver. 1.4, 2008/07/11) ------2
2 Introduction
The I-7531 is a CAN repeater used to establish a physical coupling of two
or more segments of a CAN bus system. User can implement tree or star
topologies as well as for long drop lines with I-7531. Connecting via I-7531, the
division of a CAN system into several subsystems increases the maximum
number of bus nodes.
Figure1. Application of I-7531
The I-7531 is an optically isolated CAN repeater which provides 2500 Vrms
optical isolation allowing you to separate and protect critical segments of the
system from the rest of the CAN network. And its galvanic isolation isolates
both CAN segments from each other as well as from the power supply. The
CAN connection of I-7531 is by terminal blocks. A power supply of 10 ~ 30 VDC
is required. The I-7531 is housed in a rugged DIN-Rail mountable box, making
it easy to install in an industrial cabinet. Therefore, I-7531 can be used in
CANopen, DeviceNet and generic ISO 11898-2 standard.
If user wants to know more detail information about the I-7531, please visit
our website as follow:
http://www.icpdas.com/products/Remote_IO/can_bus/i-7531.htm
I-7531 CAN Repeater User Manual (ver. 1.4, 2008/07/11) ------3
2.1 Features
High speed
Removable terminal block
Mountable on DIN Rail
Bus pins protected against transients in an industrial environment
No disturbance of the bus lines with an un-powered node
Transmit data (TxD) dominant time-out function prevents the output
drivers from driving a permanent dominant state
A thermal protection circuit is integrated to prevent the transceiver
from damage if the junction temperature exceeds thermal shutdown
level.
2.2 Specifications
Support CAN 2.0A/CAN 2.0B
Fully compatible with ISO 11898-2
Maximum communication baud : 800Kbps
Propagation Delay: ~200ns
Driving capability: Up to 100 nodes on each CAN port
Photo-coupler isolation between 2 CAN ports: 2500 Vrms
Power consumption: 2W max
CAN terminal resistors are integrated (can be disabled by jumper)
3KV galvanic isolated among of power supply and each CAN port
Power Supply: +10VDC ~ +30VDC
Operating temperature: -25°C ~ +75°C
Humidity: 5% ~ 95%
Dimensions: 122 mm x 72 mm x 35 mm
2.3 Application
Factory Automation
Building Automation
Home Automation
Vehicle Automation
Control system
Monitor system
…
I-7531 CAN Repeater User Manual (ver. 1.4, 2008/07/11) ------4
3 Technical data
3.1 Block Diagram
Figure 2 is a block diagram illustrating the functions of the I-7531 module.
Power supply are with 3000 VDC galvanic isolated between each CAN port.
Futhermore, there is photo-isolation 2500 Vrms between two CAN ports.
CAN Port 1
CAN_H
DC
DC
Physical CAN layer
120 Ohm
CAN_L
3000 VDC
Isolation
2500 Vrms
Photo Isolation
3000 VDC
Isolation
CAN Port 2
CAN_H
DC
DC
Physical CAN layer
120 Ohm
CAN_L
Block Diagram of I-7531
+10 VDC ~ +30 VDC
Figure2. Block Diagram of I-7531
I-7531 CAN Repeater User Manual (ver. 1.4, 2008/07/11) ------5
3.2 Appearance
Frame Ground
FG
GND
CAN_H
20 CAN_L
CAN Port 2
Status LED of Power
11
(CAN)
i-7531
& Communication
CAN bus Repeater
‧Support CAN 2.0A/2.0B
‧Photo-isolation: 2500 Vrms
‧Expand the number of CAN buses
‧Mountable on DIN Rail
CAN Port 1
(B)GND 10
(R)VS+
FG
GND
(CAN)
CAN_H
CAN_L 1
3000V Isolation
Power Input
Frame Ground
Figure3. Apperance of I-7531
I-7531 CAN Repeater User Manual (ver. 1.4, 2008/07/11) ------6
3.3 Pin Assignment
CAN_L 1
20 CAN_L
CAN_H
(CAN)
(CAN)
GND
CAN_H
FG
GND
FG
(R)VS+
(B)GND10
11
Figure4. Pin Aassignment of I-7531
Table1. Pin Description of I-7531
No.
Part
Name
1
CAN_L
CAN_Low. Signal Line of CAN port 1.
CAN_H
CAN_High. Signal Line of CAN port 1.
5
CAN
Port 1
7
FG
FG
9
(R)VS+
10
Power
Input
14
FG
3
GND
18
20
GND
CAN
Port 2
CAN_Ground (or CAN_GND), Voltage level of
ground of CAN_L and CAN_H of CAN port 1.
Frame Groud.
Voltage Source. It could be +10VDC ~ +30VDC.
(B)GND Power Ground.
FG
16
Description
Frame Groud.
CAN_Ground (or CAN_GND), Voltage level of
ground of CAN_L and CAN_H of CAN port 2.
CAN_H
CAN_High. Signal Line of CAN port 2.
CAN_L
CAN_Low. Signal Line of CAN port 2.
I-7531 CAN Repeater User Manual (ver. 1.4, 2008/07/11) ------7
Note 1:
In some cases, the voltage level of CAN_GND of different CAN
device in the same CAN bus system are not equal. At this time, it
could cause some problems to derogate system staibility of this
CAN bus system.
There is one way to relieve this situation; user can connect the
CAN_GND between those CAN devices to achieve equal
voltage level of CAN_GND.
Wiring of CAN_GND is not necessary; user can modify the
configuration of wiring according to actual applications.
Note 2:
Electronic circuits are constantly vulnerable to Electro-Static
Discharge (ESD), which become worse in a continental climate
area. FG(Frame Ground) provides a path for bypassing ESD to
earth ground, allowing enhanced static protection (ESD)
capability and ensures that the module is more reliable.
If user wants to use FG, both the Pin 7 and Pin 14 should be
connect to earth ground. Within the I-7531, Pin 7 and Pin 14
(FG) are not interconneced.
I-7531 CAN Repeater User Manual (ver. 1.4, 2008/07/11) ------8
3.4 Wire Connection
CAN Port 2
CAN_GND
Earth Ground
CAN_H
CAN DEVICE
CAN_L
5
9
1
6
Power
CAN Port 1
CAN_L
Power GND
CAN_H
CAN_GND
+10VDC ~ +30VDC
Earth Ground
Figure5. Wire Connection of I-7531
I-7531 CAN Repeater User Manual (ver. 1.4, 2008/07/11) ------9
3.5 Status LED
When user turn the I-7531 on, the status LED of I-7531 will be display with
red light. Moreover, when a message passes through I-7531, the status LED
will be twinkle once with yellow light while the red light is still on.
Note 3:
Twinkling rate correlates with baud rate of CAN bus. User may see
no twinkling when the twinkling period is too short because of the
higher baud rate of CAN bus. Besides, the yellow LED could look
like always on when bus loading is heavy.
3.6 Terminator Resistor Setting
According to the ISO 11898-2 specifications, the bus line of CAN_H and
CAN_L must be terminated by resistor for proper operation. The equivalent
resistance between CAN_H and CAN_L shoue be 60Ω. There are some
examples below.
Case1: RT = 120Ω
Case2: RT = 180Ω
CAN_H
RT
CAN_H
RT
RT RT
CAN_L
CAN_L
RT
Case3: RT1 = 180Ω, RT2 = 120Ω
CAN_H
RT1
RT1
RT2
CAN_L
RT1
Figure6. Terminator Resistor
I-7531 CAN Repeater User Manual (ver. 1.4, 2008/07/11) ------10
RT2
On the other hand, the I-7531 module include two build-in 120Ω
terminator resistors, user can decide to enable those two terminator resistors
or not.
The JP2 of I-7531 is used for adjusting terminal resistor on CAN Port 1,
and the JP3 of I-7531 is used for adjusting terminal resistor on CAN Port 2.
Before adjusting JP2 or JP3 of I-7531, user needs to open the cover of
I-7531 first. Those locations of JP2 and JP3 are shown as following:
JP2
JP3
CON1
CON2
Figure7. JP2 and JP3 positions
The following connection statuses present the condition if the terminal
resistor is enabled (default) or disabled.
Disable
(Deactivate)
Enable
(Activate)
Figure8. Adjustment of Terminator Resistor
I-7531 CAN Repeater User Manual (ver. 1.4, 2008/07/11) ------11
3.7 Cable Selection
The CAN bus is a balanced (differential) 2-wire interface running over
either a Shielded Twisted Pair (STP), Un-shielded Twisted Pair (UTP), or
Ribbon cable.
The table below show recommended DC parameters of CAN bus line.
Table2. Recommended DC parameters for CAN Bus Line
Wire Cross-Section [mm2]
Resistance [Ω/km]
~0.25 (AWG23)
< 90
~0.5 (AWG20)
< 50
~0.8 (AWG18)
< 33
~1.3 (AWG16)
< 20
The recommended AC parameters of CAN bus line are 120Ω impedance
and 5 ns/m specific line delay.
I-7531 CAN Repeater User Manual (ver. 1.4, 2008/07/11) ------12
3.8 Driving Capability and Baud Rate
The relationship between ideal total bus length and baud are displayed
below.
Table3. Baud, Total Bus Length, and Number of I-7531
Baud [bit/sec]
Ideal Bus Length without I-7531 [m]
Max I-7531 Number
800K
50
1
500K
100
2
250K
250
6
125K
500
12
50K
1000
25
20K
2500
62
10K
5000
125
Note 4:
When users add one I-7531 into a CAN network, the ideal total bus
length will reduce 40 meters because of the propagation delay of
I-7531. For example, if users use baud 500K and one I-7531, the
ideal total bus length will be “100 – 40 * 1 = 60 meters“.
After deciding the number of I-7531 and calculating the corresponding
ideal bus length, users can use the following table to know the maximum node
number in each segment and the maximum segment length when using
different type of wire.
Table4. Driving Capability
Wire CrossSection [mm2]
The maximum segment length [m] under the
case of specific node number in this segment
16 Nodes
32 Nodes
64 Nodes
100 Nodes
~0.25 (AWG23)
<220 m
<200 m
<170 m
<150 m
~0.5 (AWG20)
<390 m
<360 m
<310 m
<270 m
~0.8 (AWG18)
<590 m
<550 m
<470 m
<410 m
~1.3 (AWG16)
<980 m
<900 m
<780 m
<670 m
I-7531 CAN Repeater User Manual (ver. 1.4, 2008/07/11) ------13
Note 5:
The definition of segment and the relationship between segment
length (Lseg1, Lseg2 …) and ideal total bus length (Ltotal) are shown in
the following figure.
Segment 1
I-7531
Segment 2
I-7531
Segment 3
L2a
L1
L3
L2b
Lseg1
Lseg2
Lseg3
Lseg4
Ltotal
=
=
=
=
=
L1
L2a + L2b
L3
L4
Lseg1 + Lseg2 + Lseg3 + Lseg4
I-7531
Segment 4
L4
Figure9. Definition of Lseg1 and Ltotal
I-7531 CAN Repeater User Manual (ver. 1.4, 2008/07/11) ------14
4 Application Architecture
Backbone use
Backbone of CAN bus
I-7531
I-7531
CAN branch
I-7531
CAN branch
CAN branch
Electronic isolation
Extended use
I-7531
Original
CAN bus
I-7531
Extended
CAN bus
Extended
CAN bus
Electronic isolation
Figure10. Application Architecture
I-7531 CAN Repeater User Manual (ver. 1.4, 2008/07/11) ------15
5 Dimension and Mounting
35
Top View
Bottom View
50.80
56.06
121.98
35.40
56.00
25.60
58.15
71.65
Back View
Front View
35
31.50
MOUNTING
BRACKET
2-SCREW
M3
DIN- RAIL
Unit : mm
39.50
Side View
Figure11. Dimension
I-7531 CAN Repeater User Manual (ver. 1.4, 2008/07/11) ------16
Figure12. Assembly Drawing
Figure13. Mounting
I-7531 CAN Repeater User Manual (ver. 1.4, 2008/07/11) ------17
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising