CLW0214_Bigwater A80_manual_B_EN_111028.cdr
All in one Liquid Cooling System
English
English
A80
Limited Liability
These warranties replace all other warranties, expressed or implied including,
but not limited to, the implied warranties of merchantability and fitness for a
particular purpose.
Thermaltake disclaims all other warranties, expressed or implied including,
without limitation, implied warranties of merchantability and fitness for a particular
purpose.
Some jurisdictions do not allow the exclusion of implied warranties so this
limitation may not apply to you. All expressed and implied warranties are limited in
duration to the limited warranty period. No warranties apply after that period, some
jurisdiction do not allow limitation on how long an implied warranty lasts, so this
limitation may not apply to you.
Limitations of liability, Thermaltake's responsibility under this, or any other
warranty, implied or expressed, are limited to repair or replacement, as set forth
above. These remedies are the sole and exclusive remedies for any breach of
warranty. Thermaltake is not responsible for direct, special, incidental, or
consequential damages resulting from any breach of warranty or under any other
legal theory including, but not limited to, lost profits, downtime, goodwill, damage
to or replacement of equipment and property, and any cost of recovering,
reprogramming, or reproducing any program or data stored in or used with a
system containing Thermaltake product. Some jurisdictions do not allow the
exclusion or limitation of incidental or exclusions may not apply to you.
CAUTION
Before installing Thermaltake Bigwater A80 Liquid Cooling System, we
strongly suggest you to read the manual throughly and make sure all
components are included in the package. Please do follow the installation
guide step-by-step.
Improper installation may cause serious damage to the system as well
as to the water cooling unit. Thermaltake will not responsible for any
damages due to incorrect installation and incorrect usage of this product.
Extent of limited warranty, Thermaltake does not warrant that your product will
be free from design defects or errors known as "ERRATA". Current characterized
errata are available upon request. This limited warranty does not cover any costs
relating to removal or replacement of any part that is soldered or otherwise affixed
to your system's motherboard. This limited warranty does not cover damages due
to external causes, including accidental, problems with electrical power, usage not
in accordance with product instructions, misuse, neglect, alteration, repair,
improper installation, or improper testing. Nor is Thermaltake held liable for any
bodily damage that may result during the installation, maintenance, repair, or is
otherwise associated with this product, Thermaltake is free from any legal actions
that may result in death, pain and anguish, or any other form of personal damage
that may occur by purchasing this product.
You, the buyer, agree to this warranty and its term set within its expressed and
implied limited warranty. This limited warranty gives you specific legal rights, and
you may also have other right that varies from jurisdiction to jurisdiction.
All in one Liquid Cooling System
A80
All in one Liquid Cooling System
Specification
Compatibility
(CPU Socket)
Water Block
Pump
Fan
Radiator
Tube
Weight
English
English
A80
Components
Intel LGA 2011/1366/1155/1156/775
AMD FM1/AM3+/AM3/AM2+/AM2
Copper (Base)
Material
Dimension
77 x 77 x 56 mm
Bearing
Ceramic bearing
Motor speed
1750~3000 RPM
Rated Voltage
DC 12V
Rated Current
DC 0.45 A (max)
Input Current
0.5 A
Dimension
120 x 120 x 25 mm
Speed
1200~2500 RPM
Noise Level
20~43 dBA
Rated Voltage
12 V
Connector
3 pin
Max. Air Flow
101.6 CFM
Power Input
6W
Dimension
156 x 120 x 32.5 mm
Material
Aluminum
Dimension
Ø 8.1
Material
FEP
800 g
A
Mounting clip
Intel 1366/1156/775 x 2
B
Mounting clip
AMD FM1/AM3+/AM3/
AM2+/AM2 x 2
D
Screw x 4 (for Intel & AMD
Mounting clips )
E
Screw x 4
Intel 1366/1156/1155/775
AMD FM1/AM3+/AM3/AM2+/AM2
G
Retention spring x 4
H
Rubber ring x 4
I
Plastic spacer x 4
J
Post x 4
K
Screw x 4 (for radiator)
L
Bigwater A80 unit x 1
All in one Liquid Cooling System
C
Back Plate Intel/AMD
x1
F
Screw x 4
Intel 2011
A80
All in one Liquid Cooling System
Installation steps
English
English
A80
Install Waterblock
We strongly suggest the following installation procedures.
Failure to comply may result in leaks and damaged components .
Intel LGA 1366/1156/1155/775 Installation
Before Installation, please verify the CPU
platform and select the appropriate holes
for your CPU socket.
Components Check
Install Waterblock
Intel LGA 1366/1156/1155/775
Intel LGA 2011
AMD FM1/AM3+/AM3/AM2+/AM2
1366
1566/1155
P1.
P2.
P3.
775
When you install an Intel CPU, please make
sure that the back plate side facing away from
the motherboard shows “INTEL”.
I
Install Radiator
P4.
C
J
Fan and Pump Connection
From beneath the motherboard,
carefully attach the back
plate(C) and insert the posts(J)
through the motherboard
mounting holes.
Fasten the plastic spacers(I)
over each post.
Exploded View
P4.
**Remove protective cover from
waterblock before attaching on
the CPU.
Installation Complete
E
G
Fasten the Intel mounting
clips(A) on waterblock with
screws(D).
H
A
I
C
J
All in one Liquid Cooling System
Assemble screws(E),
retention springs(G) and
mounting clips with rubber
rings(H) together.
Place the assembled
waterblock onto the CPU and
tighten it on each posts(J).
A80
1
All in one Liquid Cooling System
Install Waterblock
Install Waterblock
AMD FM1/AM3+/ AM3/AM2+/AM2 Installation
Intel LGA 2011 Installation
Exploded View
English
English
A80
**Remove protective cover from
waterblock before attaching on
the CPU.
When you install an AMD CPU, please
make sure that the back plate side facing
away from the motherboard shows “AMD”
F
G
I
A
H
Fasten the Intel mounting
clips(A) on waterblock with
screws(D).
C
J
D
From beneath the motherboard,
carefully attach the back
plate(C) and insert the posts(J)
through the motherboard
mounting holes.
Fasten the plastic spacers(I)
over each post.
Exploded View
**Remove protective cover from
waterblock before attaching on
the CPU.
Assemble screws(F),
retention springs(G) and
mounting clips with rubber
rings(H) together.
Place the assembled
waterblock onto the CPU and
fasten it on motherboard.
Fasten the AMD mounting
clips(B) on waterblock with
screws(D).
E
G
B
H
I
C
J
2
All in one Liquid Cooling System
Assemble screws(E),
retention springs(G) and
mounting clips with rubber
rings(H) together.
Place the assembled
waterblock onto the CPU and
tighten it on each posts(J).
A80
3
All in one Liquid Cooling System
English
English
A80
Install Radiator
Mount radiator to fan housing and secure with screws (K).
K
Airflow
Fan and Pump Connection
Connect the fan and pump connectors to free headers
on motherboard. Installation complete.
4
All in one Liquid Cooling System
A80
5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising