120-277v Install DL HID

120-277v Install DL HID
INSPECTED BY:
INSTALLATION INSTRUCTIONS FOR
120V & 277V H.I.D. DIRECTIONAL LIGHTS
INSTALLATION FOR H.I.D. FIXTURES:
Warning: Fixtures must be installed and grounded in accordance
with the National Electrical Code (NEC) and local codes. Fixtures
must be installed by a licensed electrician per local codes.
NOTE: To prevent electrical shock, disconnect from electrical
supply before installation or service.
1.Using thread sealant, thread fixture onto junction box or other mounting device (not supplied) until it is at desired direction. Tighten provided lock nut to ensure that the fixture is firmly locked into position.
2.Attach fixture leads to line-in leads from ballast (DL-40 is self-
ballasted) observing polarity (black to black, white to white and green to ground) using approved silicone filled safety wire connectors.
3.Coat any exposed fixture threads with thread sealant to prevent moisture from entering mounting device.
4.To adjust fixture aiming angle, loosen swivel screw using a #2 Phillips screwdriver. Do not remove completely. Hold fixture at selected angle and tighten swivel screw firmly.
5.Install H.I.D. light bulb – see lamp installation/replacement instructions below.
6. Turn on power to the fixture and check for proper operation.
DISTANCE LIMITATIONS
Do not mount HID fixture over 10 feet away from ballast.
If application required runs longer than 10 feet, specify a Long
Range Igniter to operate HID fixtures (add -LRI to catalog #)
DL-40 DL-40
(Self ballasted)
(Self ballasted)
DL-38-EC
DL-38-EC
S
CU
S
FOCU
FO
S
FOCU
Recommend
Recommend
Focus FA-26
Focus FA-26
DB-120DB-120
H.I.D. Ballast
H.I.D. Ballast
NOTE: Avoid aiming light fixture directly upward. Set at an angle
to prevent rain or irrigation water from settling on lens.
LAMP INSTALLATION/REPLACEMENT
NOTE: Turn off power before servicing fixture.
To re-lamp DL-16, remove four screws from lens cap using a #2 Phillips screwdriver.
Carefully remove lens cap and gasket. Replace ED-17 medium base H.I.D. light bulb
with correct lamp wattage and type marked on fixture label. Insert gasket into lens
cap and assemble lens cap onto body. Make sure gasket seats properly between
body and cap before tightening screws to ensure a weatherproof seal.
120v-277v
120v-277v
120v-277v
120v-277v
To re-lamp (C)DL-20, DL-30 & (C)DL-38, loosen thumb screw on bottom of cap.
Hold body and cap with each hand. Rotate and pull to separate. Replace ED-17, PAR
or R medium base H.I.D. light bulb with correct lamp wattage and type marked on
fixture label. Re-install cap onto body by rotating cap in circular motion while sliding
cap into the body. DO NOT push cap straight into body to prevent O-ring from
slipping out of its groove. Tighten thumb screw when assembled.
120v-277v
120v-277v
FO
CU
S
DL-30-AC
To re-lamp DL-40, remove two screws from lens cap using a #2 Phillips screwdriver.
Carefully remove lens cap and gasket. Replace H.I.D. light bulb with correct G12
lamp wattage and type marked on fixture label. Insert gasket into lens cap and
assemble lens cap onto body. Make sure gasket seats properly between body and
cap before tightening screws to ensure a weatherproof seal.
FA-22-Tree
DL-38-EC
To Fixture
DL-40
CAUTION: Do not
exceed
maximum wattage marked on (Self
ballasted)
fixture label.
S
CU
FO
S
FOCU
IMPORTANT SAFETY INSTRUCTIONS TO REDUCE THE RISK OF FIRE AND INJURY TO PERSONS:
1. Lamp gets hot quickly; turn off, unplug/disconnect and allow to cool down
before replacing the light bulb.
Recommend
Focus FA-26
2. DO NOT touch hot lens, use guard or enclosure.
DB-120
3. DO NOT look into lamp when on.
H.I.D. Ballast
4. Keep lamp away from materials that may burn.
5. Use only with wattage/lamp marked on fixture warning and instructions.
6. Use the correct light bulb base with the correct socket.
7. DO NOT touch lamp at anytime. Use a lint-free cloth when handling the
Halogen light bulbs as oil from skin may damage lamp and shorten lamp life.
8. DO NOT operate fixture with missing or damaged shield or lens.
120v-277v
120v-277v
120v-277v
To Fixture
For Questions Call 1-888-882-1350
120-277v Install DL HID
032112
D
FOCUS
WT-120
120v-277v
To Fixture
To Fixture
S
CU
FO
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising