Set up BookDrive Mark ll

Set up BookDrive Mark ll
Set up BookDrive Mark ll
www.atiz.com/support
Safety Precautions
Place the machine on a level table to ensure proper working condition.
Do not tilt the machine.
Do not place the machine near heaters or volatile, flammable or
combustible materials that may catch fire.
The machine is not designed to be lifted. Do not lift or relocate the
machine once it has been fully assembled. To relocate the machine,
de-assemble it into parts first and then re-assemble them again at the
desired location.
1
Getting to know your BookDrive Mark ll
Roof
LED Lighting Panel
Arm structure
Arm
Camera mount
Pillar
V-Platen
V-Cradle
Base
2
Shade
How to assemble
1.
Mark II comes in 3 boxes.
Box 1
- Pillar
- LED light panel
- Roof
- Arm
- Accessories
- Screws
2.
Box 2
- V-Platen
- Arm structure
Box 3
- Base
- V-Cradle
- Shade
Open Box 1. Take the pillar out. Put it on the ground. Connect the LED
lighting panel to the pillar by sliding it in as shown. The label on the stickers
between pieces must match.
2.1. Tighten the 4 screws as shown below.
2.2. Connect the power cord from the lighting panel to the power cord
originating from the pillar of the Mark II.
3
3.
Now put the pillar on the desk you plan to operate the scanner.
3.1. Open Box 3. Take the base
out. Connect the base piece to
the base of the pillar as shown.
4.
4
3.2. Tighten 6 screws
Open Box 2 and connect the left and right arms to the pillar.
4.1. Connect the left arm to the
pillar first. Identify the label on
the stickers between the two
pieces and make sure they
match. Tighten the 2 screws.
View from the back of the machine
5.
4.2. Connect the right arm to the
pillar and tighten the two
screws.
By this point, the machine should
look like this
Take the 2 pieces of the roof out from Box 1.
5
5.1. Attach the roof to the LED
lighting panel and tighten the 2
screws that are already affixed
to the LED panel.
5.2. Insert a third screw and tighten
as shown below.
Insert the
screw here
5.3. Repeat this exact same process on the other side.
View from the back of the machine
6
6.
Take the 2 arms from Box 1. The arms look like the picture below. Next
you will attach the arms to each side.
6.1. On the left and right side use the 4 screws to connect the arms to the
structure as shown below.
7
6.2. Repeat the exact same process on the other side.
7.
8
Take the V shaped cradle from Box 3 and connect it to the rails of the
base.
8.
Take the V shaped platen out of Box 2. Use the screws (4 screws) that
are at the plate of the pillar. Tighten them once the platen has been
affixed.
9.
Remove the 2 screws that currently limit the movement of the V platen
(these 2 screws are there to limit the movement during the transportation).
The V platen can now be lifted and lowered.
9
Connecting Shade Pieces to the Machine
10.1. Connect the the right and left shade parts to the back of the machine by
using the built-in magnets.
10.2. Connect the back cover by using the built-in magnets.
10
10.3. Attached the top shade as shown below.
10.4. Attach the shades on the left and right side as shown below.
11
10.5. Attach the front shade as shown below.
10.6. Attach the outer shade that covers the cameras and arms as shown
below.
12
10.7. You can fold it up to make it easier to configure the cameras, and then
fold it back once the cameras have been configured.
10.8. The LED shade on the front and sides
A.
C.
B.
13
How to use the V cradle
14
1.
The two sides of the V cradle and be widened apart. If you want to do
that, release the knobs and push the sides of the V cradle apart.
2.
The angle of each side of the V cradle can also be individually altered.
Do that by adjusting these two pieces as shown.
How to make images straight
When the camera is not perfectly aligned resulting in a slightly rotated image,
you can do micro adjustment at the plate where the camera is mounted.
Your image should come out straight and look like this.
If you image looks like A, then loosen the screws 1 slightly and then adjust
screws 2 to compensate until the image is properly aligned. Once the camera
is properly aligned then proceed to tighten screws 1.
If you image looks like B, loosen screws 1 and then adjust screws 3 to
compensate until image is aligned properly. Once it is aligned then tighten
screws 3.
15
The LED Light and the Auto Capture Switch
The LED light switch and LED Power jack are on the side of the pilar
16
Auto Capture Switch
1.
Slide the cradle to the left to connect the USB cable to the port located
on the right side of the base.
2.
Slide the cradle to the right and then you can turn on the Auto Capture
Switch located on the left side of the base.
17
How to install camera
1. Turn lever “A” counter clockwise
2. Press The safety button “B”
3. Slide out the plate “C“
4. Mount the sliding plate “C“ to camera
5. Silde in the plate “C”
6. Turn lever “A” clock wise
C
3.
4.
5.
B
1.
2.
A
6.
A
How to install camera hood
Insert hot Shoe adaptor to camera flash mount frist then install camera hood
to hot shor adaptor
18
www.atiz.com/support
@Copyright 2006-2011. Atiz Innovatin Co.,Ltd. All rights reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising