SILENCERCO OMEGA

SILENCERCO OMEGA
SILENCERC O
OMEGA
FIELD MANUAL
Thank you for choosing to add a SilencerCo silencer to your collection. We
manufacture all of our products under one roof here in the USA and are proud to
deliver only the best silencers to our community. We hope you will enjoy using this
product as much as we enjoyed making it and welcome to our family.
Sincerely and Silently,
JOSHUA WALDRON
SilencerCo Co-Founder & CEO
WE AT SILENCERCO ® HOPE THAT YOU ENJOY THE
TECHNOLOGICAL ADVANCEMENTS OFFERED BY THE
OMEGA T M SOUND SUPPRESSOR. TO PROVIDE FOR YOUR
SAFET Y AND THE EFFECTIVE USE OF THIS SUPPRESSOR,
IT IS CRITICAL THAT THE OWNER AND ANY USER OF
THE SUPPRESSOR RE AD THIS ENTIRE MANUAL AND
FOLLOW STRICTLY THE WARNINGS AND INSTRUCTIONS
WITHIN. THIS SUPPRESSOR IS INTENDED TO BE USED
ONLY BY THOSE WHO ARE WELL-VERSED IN THE SAFE
OPER ATION OF FIRE ARMS.
DISCL AIMER
The manufacturer is not responsible for improper usage of this product. This product
is potentially dangerous, and, as such, it is the user’s responsibility to understand
and implement its proper use. If you do not understand the instructions in this
manual, please contact the manufacturer for further clarification at 801.417.5384.
SONIC CR ACK
The Omega is designed to suppress the initial muzzle blast and subsequent projectile
de-corking pressure. The Omega does not contact or otherwise interact with the
projectile, allowing the projectile to travel at its default speed. Because of this, a
sonic crack is produced by the projectile as it breaks the sound barrier. Depending
on the geography of the area, the sonic crack may vary in volume. This is solely a
function of the projectile breaking the sound barrier and is not related to suppressor
performance.
OMEGA
WA RN I N G
Failure to follow installation and maintenance instructions detailed in this
manual may result in serious personal injury and damage to the weapon.
Firearm sound suppressors are user-attached firearm muzzle devices, and as
such are subject to improper attachment issues unless the procedures outlined in
this manual are followed precisely. Do not attempt to use this product unless you
have specific training and experience in the use of firearms.
Before installing or removing the Omega sound suppressor from the host
weapon, be sure that the weapon is unloaded and the action is opened so that
it is visibly clear of any ammunition. If you are at all unsure as to the proper
procedures to ensure that your firearm is unloaded, please consult your firearm
user’s manual/instructions and/or contact a properly licensed dealer or the
manufacturer of your weapon.
Because suppressed firearms make less noise than unsuppressed firearms, it is
easy to forget that they are still firearms and capable of causing bodily injury and
property damage. It is of vital importance to remember that a suppressed firearm
is just as dangerous as an unsuppressed firearm, and that the same safe handling
requirements still apply.
When removing the Omega, use extreme caution as it may be hot to the touch
after firing. Use gloves to avoid burns or other injuries.
Check the fit between barrel and suppressor before firing! The thread mount must
be fully shouldered on the barrel. There should be no visible gap between the
barrel shoulder and the face of the suppressor thread mount. If there is any gap
DO NOT fire the host with the suppressor attached. Poor accuracy and product
damage may result if the suppressor is not fully shouldered.
Assembly and disassembly should never be performed while the suppressor is
affixed in any manner to a host firearm. Always completely remove the Omega
from the host firearm before assembly and/or disassembly is attempted.
Before performing maintenance, removing, or installing the suppressor, open the
action, ensure firearm is unloaded, and be sure the chamber is empty. Failure to
do so can result in property damage, injury, or death.
MADE IN THE USA
The Omega is shorter, lighter and quieter than any other centerfire rifle
suppressor on the market. In addition to its performance, the Omega’s design
allows for maximum user adaptability and convenience. Each Omega comes
with a 5/8 X 24 direct thread mount, a quick detach Active Spring Retention
(ASR) mount complete with a Specwar ASR muzzle brake, and an Anchor Brake.
All other accessories, including additional muzzle devices and endcaps, are
sold separately. The Omega is full-auto rated and is compatible with a range of
ammunition from .22 Hornet to .300 Winchester Magnum.
P RO D U C T S P E C S
The Omega is rated down to 10" barrels for .223 Remington/5.56 NATO, 16"
barrels for .308 Winchester/7.62 NATO, and 20” barrels for .300 Win Mag.
INCLUDED
The Omega ships with the attached direct thread mount and Anchor Brake, as
well as an Active Spring Retention (ASR™) quick-detach mount and muzzle
brake (included in box). All tools required for installation and removal are
included.
Suppressors must be free of obstructions such as mud, dirt, etc. Do NOT attempt to
shoot through an obstructed suppressor.
The Omega was designed to be used “dry” and free of any ablative media, such
as grease and water. If submerged in water, the user must allow a minimum 6
second drain time after exiting the water.
MOUNTING OP TIONS
Whether you prefer the simple, shorter nature of a direct thread setup, or the
quick attach/detach features of the ASR Mount, you should take care to ensure
that the Omega is mounted securely to your firearm before firing. These
instructions will help to prevent the problems and dangers that can arise from
improper seating.
OMEGA
ASR MOUNT
DIRECT
THREAD MOUNT
MUZZLE
BRAKE
OMEGA
BASIC TOOL
HARVESTER 338
MULTITOOL
ASR MOUNT
AT TACH SUPPRES SOR TO FIRE ARM
The ASR Mount is a proprietary mounting system, and as such requires a
complementary muzzle brake (included).
After confirming that your firearm is unloaded, place the threaded end of
the Omega (1A) in line with the threads of the barrel (2A.) Taking care not to
cross-thread, screw the suppressor onto the barrel until it is firmly secured and
no additional barrel threading is visible. To remove from host, reverse these
instructions.
3A
1A
1A
D I RE C T T H RE A D M O U N T
Hand tighten only.
REMOVAL AND INSTALL ATION OF DIRECT THRE AD MOUNT
2A
Hold the Omega body (1A) with a firm grip and use the three pegs of the
Harvester Big Bore Multitool (3A) in a counter-clockwise direction to loosen the
coupler from the bottom of the suppressor. To install, reverse these instructions,
starting the thread by hand to avoid cross-threading.
Crush washers are NOT recommended as they do not crush uniformly and WILL
cause improper mounting and baffle strikes. SilencerCo recommends the use of a peel
washer or the included shim kit if any indexing of the mount is required.
For proper alignment, it is essential that the muzzle brake seats against a 90°
barrel shoulder. The flash hider/muzzle brake should be torqued to 20–30 ft-lbs.
Use of Rocksett™ or Loctite Red 271™ is recommended.
PEEL WASHER
CRUSH WASHER
(DO NOT USE)
MUZZLE DEVICE
1B
UNLOCKED
1B
2B
3B
Thread the ASR Mount (1B) assembly onto the Omega suppressor body (2B) by
hand, taking care not to cross-thread.
Remove your existing muzzle device using a 3/4" open end wrench. Remove the
crush washer from barrel threads.
Hold the Omega body (2B) with a firm grip. Using the Omega Basic Tool (3B)
to grasp the notches in the base of the ASR mount (1B), tighten the coupler in a
clockwise direction. Torque to approximately 35 ft-lbs.
Install the muzzle brake (1C) by threading it onto the barrel (2C.) Use the provided
shim kit to ensure proper muzzle brake alignment. Tighten onto barrel using a
3/4" open end wrench. Use of Rocksett™ or Loctite Red 271™ is recommended
to secure the muzzle brake.
1C
1C
2B
LOCKED
2C
2C
ANCHOR BRAKE
Verify the ASR collar (1D) is in the unlocked position, with locking collar rotated
clockwise, before installing.
2D
Install the Omega (2D) by sliding the back end over the muzzle brake until it
stops, then turn the suppressor (2D) clockwise to hand tighten.
Rotate the ASR collar (1D) counter-clockwise to the locked position.
To remove, perform steps in reverse order.
To remove the Anchor Brake (1E) from the Omega (2E), line up the three pegs on
the Harvester 338 Multitool (3E) with the holes on top of the brake. Holding the
suppressor with a firm grip, rotate the tool counter-clockwise until the brake is
removed.
To install Anchor Brake, perform steps in reverse order, starting the thread by
hand to avoid cross-threading.
1E
3E
WA R N I N G Firing the Omega without the Anchor Brake or a SilencerCo endcap
will negate benefits of using a suppressor and will void the warranty
1E
2E
1D
1D
MAINTENANCE
The Omega typically requires limited maintenance.
Mounts should periodically be cleaned with any standard gun cleaning solvent
and a brush to remove any carbon or fouling. If necessary, run a cleaning brush
through the bore to remove any light fouling of the suppressor.
L I FE T I M E WA RR A N T Y
Do not run cleaning patches through the bore as the patches might become lodged in
the suppressor and cause damage upon firing.
C A U T I O N Always read the warning label on any cleaner or solvent, and
remember that virtually all solvents are inherently dangerous and potentially
toxic. Always use adequate ventilation and both skin and eye protection when
using solvents.
We proudly stand behind the quality of our products with a lifetime warranty,
no matter what—even if it’s not a product defect. Our 48 hour repair turnaround
even warranties stupid… once. If you experience any issues, please contact our
Customer Service team at 801.417.5384.
If your silencer has a defect in manufacturing or materials, there will be no
charges for service or replacement through our SilencerCo facility.
If we determine that a claim is not covered under warranty, a discounted
replacement option will be granted.
This warranty does not cover damage to the silencer or host firearm resulting
from careless or irresponsible handling, adjustments or modifications to design,
negligence, or other abuse. SilencerCo assumes no liability for unsafe or illegal
use of the silencer by its purchaser or any other user that comes in contact with
the product after purchase. SilencerCo assumes no responsibility for physical
injury or property damage resulting from careless or irresponsible handling or
by any use contrary to the recommendations, warnings, and cautions generally
listed in this manual. SilencerCo does not cover damage to the silencer or
host firearm resulting from improper hand-loaded or reloaded ammunition or
defective ammunition.
RE PA I R P O L I C Y
Should the silencer require repair or modification, the owner should contact
SilencerCo either in writing or by telephone. Many problems can be handled
without having to return the product. If it is determined that the product needs
to be returned for repair or modification Contact SilencerCo customer service
801.417.5384 where an RMA number will be provided. Do not return the
suppressor to SilencerCo until you have contacted customer service as an RMA
code must be provided.
If repairs are required due to a defect in manufacturing or materials, there will
be no charge for repairs. Subject to any restrictions set forth herein, SilencerCo
agrees to replace and/or repair the Harvester for an unlimited amount of time.
This warranty covers repair, service, and replacement of damaged product
caused by normal use, free of charge, only if performed at a SilencerCo facility.
Should a silencer require repair, the owner must contact SilencerCo and make
arrangements to return the product. Customer must return damaged product
with a legible copy of the approved ATF form and a legible written description
of the problem, defect, and/or malfunction. Please include in written description
the serial number of the product and the events leading up to the issue, including
what ammunition has been used and any host weapons that have been used.
If SilencerCo determines, at its sole and absolute discretion, that a returned
suppressor is not covered under this warranty, for any reason, you may purchase a
replacement product at 75% off the suggested retail price.
Register Your SilencerCo Product Online
To Activate Your Lifetime Warranty
S IL E N C E RC O. C O M / RE GI S T E R
J OIN N OW
Protect Your Rights | Protect Your Hearing
The American Suppressor Association is fighting to protect and expand your
silencer rights. Join the fight today!
LEARN MORE AT AMERICANSUPPRESSORASSOCIATION.COM
FOR QUES TIONS, CONTAC T OUR CUS TOMER SERVICE TE AM AT 801.417.5384 OR INFO@SILENCERCO.COM
© 2017 SilencerCo, LLC. All Rights Reserved. The contents of this publication may not be reproduced in any form
or by any means in whole or in part without the prior written permission of the copyright owner.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising