Manual

Manual
WAGO-I/O-SYSTEM 750 XTR
Pos : 2 /D okumentati on allgemein/Ei nband/Ei nband H andbuch - Fronts eite 2015 - mit Doc Variabl en (Standar d) @ 9\mod_1285229289866_0.doc x @ 64941 @ @ 1
Manual
750-8202/040-000
PFC200 CS 2ETH RS /XTR
PLC – Controller PFC200 /XTR
Version 1.1.0, valid from
FW Version 02.04.22(06)
Pos : 3 /Alle Serien (Allgemeine M odul e)/Rec htlic hes, Allgemei nes/Impressum für Standardhandbüc her - allg. Angaben, Ansc hriften, T elefonnummer n und E-Mail-Adres sen @ 3\mod_1219151118203_21.doc x @ 21060 @ @ 1
2
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
© 2016 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone:
Fax:
+49 (0) 571/8 87 – 0
+49 (0) 571/8 87 – 1 69
E-Mail:
info@wago.com
Web:
http://www.wago.com
Technical Support
Phone:
Fax:
+49 (0) 571/8 87 – 5 55
+49 (0) 571/8 87 – 85 55
E-Mail:
support@wago.com
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail:
documentation@wago.com
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
=== Ende der Liste für T extmar ke Ei nband_vorne ===
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table of Contents
3
Pos : 5 /D okumentati on allgemein/Verzeic hnisse/Inhalts verz eichnis - Ü berschrift oG und Verzei chnis @ 3\mod_1219151230875_21.doc x @ 21063 @ @ 1
Table of Contents
1
1.1
1.2
1.3
1.4
1.5
Notes about this Documentation ............................................................... 15
Validity of this Documentation ............................................................... 15
Copyright................................................................................................. 15
Symbols ................................................................................................... 16
Number Notation ..................................................................................... 18
Font Conventions .................................................................................... 18
2
Important Notes ......................................................................................... 19
2.1
Legal Bases ............................................................................................. 19
2.1.1
Subject to Changes ............................................................................. 19
2.1.2
Personnel Qualifications ..................................................................... 19
2.1.3
Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions ........................................................................ 19
2.1.4
Technical Condition of Specified Devices ......................................... 20
2.2
Safety Advice (Precautions) .................................................................... 21
2.3
Licensing Terms of the Software Package Used ..................................... 23
2.4
Special Use Conditions for ETHERNET Devices .................................. 23
3
Device Description ..................................................................................... 24
3.1
View ........................................................................................................ 27
3.2
Labeling................................................................................................... 29
3.2.1
Manufacturing Number ...................................................................... 29
3.3
Connectors............................................................................................... 30
3.3.1
Data Contacts/Internal Bus ................................................................. 30
3.3.2
Power Jumper Contacts/Field Supply ................................................ 31
3.3.3
CAGE CLAMP® Connectors ............................................................. 32
3.3.4
Service Interface ................................................................................. 33
3.3.5
Network Connections – X1, X2 ......................................................... 34
3.3.6
RS-232/RS-485 – X3 Communication Connection ........................... 35
3.3.6.1
Operating as an RS-232 Interface .................................................. 36
3.3.6.2
Operating as an RS-485 Interface .................................................. 37
3.4
Display Elements .................................................................................... 38
3.4.1
Power Supply Indicating Elements .................................................... 38
3.4.2
Fieldbus/System Indicating Elements ................................................ 39
3.4.3
Memory Card Indicating Elements .................................................... 40
3.4.4
Network Indicating Elements ............................................................. 41
3.5
Operating Elements ................................................................................. 42
3.5.1
Operating Mode Switch ...................................................................... 42
3.5.1.1
CODESYS 2 Runtime System....................................................... 42
3.5.1.2
e!RUNTIME Runtime System ....................................................... 42
3.5.2
Reset Button ....................................................................................... 43
3.6
Slot for Memory Card ............................................................................. 44
3.7
Schematic Diagram ................................................................................. 45
3.8
Technical Data ........................................................................................ 46
3.8.1
Device ................................................................................................. 46
3.8.2
System Data ........................................................................................ 46
3.8.3
Supply ................................................................................................. 46
3.8.4
Clock................................................................................................... 47
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
4
Table of Contents
3.8.5
3.8.6
3.8.7
3.8.8
3.8.9
3.8.10
3.8.11
3.9
3.10
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Programming ...................................................................................... 47
Internal data bus ................................................................................. 47
ETHERNET ....................................................................................... 48
Serial interface .................................................................................... 48
Connection Type ................................................................................ 48
Mechanical Conditions ....................................................................... 49
Climatic Environmental Conditions ................................................... 49
Approvals ................................................................................................ 50
Standards and Guidelines ........................................................................ 52
4
Function Description ................................................................................. 56
4.1
Network ................................................................................................... 56
4.1.1
Interface Configuration ...................................................................... 56
4.1.1.1
Operation in Switch Mode ............................................................. 56
4.1.1.2
Operation with Separate Network Interfaces ................................. 56
4.1.2
Network Security ................................................................................ 57
4.1.2.1
Users and Passwords...................................................................... 57
4.1.2.1.1
Services and Users .................................................................... 57
4.1.2.1.2
WBM User Group ..................................................................... 58
4.1.2.1.3
Linux® User Group ................................................................... 58
4.1.2.1.4
SNMP User Group .................................................................... 58
4.1.2.2
Web Protocols for WBM Access ................................................... 59
4.1.3
Network Configuration ....................................................................... 60
4.1.3.1
Host Name/Domain Name ............................................................. 60
4.1.3.2
Default Gateways ........................................................................... 60
4.1.4
Network Services................................................................................ 61
4.1.4.1
DHCP Client .................................................................................. 61
4.1.4.2
DHCP Server ................................................................................. 61
4.1.4.3
DNS Server .................................................................................... 63
4.2
Memory Card Function ........................................................................... 64
4.2.1
Backup Function (Saving of Device Settings to the Memory Card) .. 65
4.2.2
Restore Function (Loading of Device Settings from the Memory
Card) ................................................................................................... 66
4.2.3
Inserting a Memory Card during Operation ....................................... 67
4.2.4
Removing the Memory Card during Operation.................................. 67
4.2.5
Setting the Home Directory for the Runtime System ......................... 68
5
Mounting..................................................................................................... 69
5.1
Mounting Position ................................................................................... 69
5.2
Overall Configuration ............................................................................. 69
5.3
Mounting onto Carrier Rail ..................................................................... 70
5.3.1
Carrier Rail Properties ........................................................................ 70
5.3.2
WAGO DIN Rail ................................................................................ 71
5.4
Spacing .................................................................................................... 72
5.5
Mounting Sequence ................................................................................. 73
5.6
Inserting Devices ..................................................................................... 74
5.6.1
Inserting the Controller....................................................................... 74
5.6.2
Inserting the I/O Module .................................................................... 75
6
6.1
Connect Devices ......................................................................................... 76
Power Contacts/Field Supply .................................................................. 76
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
6.2
6.3
6.3.1
6.3.2
6.3.3
6.4
6.4.1
6.4.1.1
6.4.1.2
6.4.2
6.5
6.5.1
6.5.2
6.5.3
6.5.4
Table of Contents
5
Connecting a Conductor to the CAGE CLAMP® ................................... 78
Power Supply Concept ............................................................................ 79
Supplementary Power Supply Regulations ........................................ 79
Supply Example.................................................................................. 81
Power Supply Units ............................................................................ 83
Grounding ............................................................................................... 84
Grounding the DIN Rail ..................................................................... 84
Framework Assembly .................................................................... 84
Insulated Assembly........................................................................ 84
Grounding Function............................................................................ 85
Shielding ................................................................................................. 86
General ............................................................................................... 86
Bus Cables .......................................................................................... 86
Signal Lines ........................................................................................ 87
WAGO Shield Connecting System .................................................... 87
7
Commissioning ........................................................................................... 88
7.1
Switching On the Controller ................................................................... 88
7.2
Determining the IP Address of the Host PC ........................................... 89
7.3
Setting an IP Address .............................................................................. 90
7.3.1
Assigning an IP Address using DHCP ............................................... 91
7.3.2
Changing an IP Address Using the “CBM” Configuration Tool
via the Serial Interface ........................................................................ 92
7.3.3
Changing an IP Address using “WAGO Ethernet Settings” .............. 95
7.3.4
Temporarily Setting a Fixed IP Address ............................................ 97
7.4
Testing the Network Connection ............................................................ 98
7.5
Changing Standard Passwords ................................................................ 99
7.6
Shutdown/Restart .................................................................................. 100
7.7
Initiating Reset Functions ..................................................................... 101
7.7.1
Warm Start Reset .............................................................................. 101
7.7.1.1
CODESYS 2 Runtime System..................................................... 101
7.7.1.2
e!RUNTIME Runtime System ..................................................... 101
7.7.2
Cold Start Reset ................................................................................ 101
7.7.2.1
CODESYS 2 Runtime System..................................................... 101
7.7.2.2
e!RUNTIME Runtime System ..................................................... 101
7.7.3
Software Reset .................................................................................. 102
7.8
Configuration ........................................................................................ 103
7.8.1
Configuration via Web-Based-Management (WBM) ...................... 104
7.8.1.1
WBM User Administration.......................................................... 105
7.8.1.2
General Information about the Page ............................................ 109
7.8.1.3
“Status Information” Page ........................................................... 112
7.8.1.3.1
“Controller Details” Group ..................................................... 112
7.8.1.3.2
“Network Details (Xn)” Group(s) ........................................... 112
7.8.1.4
“General PLC Runtime Configuration” Page .............................. 113
7.8.1.4.1
“General PLC Runtime Configuration” Group ....................... 113
7.8.1.5
“PLC Runtime Information” Page ............................................... 115
7.8.1.5.1
“PLC Runtime” Group ............................................................ 115
7.8.1.5.2
“Project Details” Group .......................................................... 115
7.8.1.5.3
“Task n” Group(s) ................................................................... 116
7.8.1.6
“PLC WebVisu” Page.................................................................. 117
7.8.1.6.1
“Web Server Configuration” Group ....................................... 117
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
6
Table of Contents
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.1.7
7.8.1.7.1
7.8.1.7.2
7.8.1.8
7.8.1.8.1
7.8.1.8.2
7.8.1.8.3
7.8.1.9
7.8.1.9.1
7.8.1.9.2
7.8.1.10
7.8.1.10.1
7.8.1.10.2
7.8.1.10.3
7.8.1.11
7.8.1.11.1
7.8.1.11.2
7.8.1.11.3
7.8.1.12
7.8.1.12.1
7.8.1.12.2
7.8.1.12.3
7.8.1.13
7.8.1.13.1
7.8.1.13.2
7.8.1.13.3
7.8.1.13.4
7.8.1.14
“Configuration of Host and Domain Name” Page ...................... 118
“HostName” Group ................................................................. 118
“Domain Name” Group .......................................................... 118
“TCP/IP Configuration” Page...................................................... 119
“IP Configuration (Xn)” Group(s) .......................................... 119
“Default Gateway n” Groups .................................................. 119
“DNS Server” Group .............................................................. 120
“Ethernet Configuration” Page .................................................... 121
“Switch Configuration” Group ............................................... 121
“Interface Xn” Groups ............................................................ 121
“General Firewall Configuration” Page....................................... 123
“Global Firewall Parameters” Group ...................................... 123
“Firewall Parameters Interface Xn” Group ............................. 124
“Firewall Parameter Interface VPN” Group ........................... 125
“Configuration of MAC Address Filter” Page ............................ 126
“Global MAC Address Filter State” Group ............................ 126
“MAC Address Filter State Xn” Group .................................. 127
“MAC Address Filter Whitelist” Group ................................. 127
“Configuration of User Filter” Page ............................................ 128
“User Filter” Group ................................................................. 128
“User Filter n” Group .............................................................. 128
“Add New User Filter” Group ................................................ 129
“Configuration of Time and Date” Page ..................................... 130
“Date on Device” Group ......................................................... 130
“Time on Device” Group ........................................................ 130
“Timezone” Group .................................................................. 131
“TZ String” Group .................................................................. 131
“Configuration of the Users for the Web-based Management”
Page.............................................................................................. 132
“Change Password for Selected User” Group......................... 132
“Create Bootable Image” Page .................................................... 133
"Create Bootable Image from Active Partition (<Active
Partition>" Group .................................................................... 133
“Configuration of Serial Interface RS232” Page ......................... 135
“Serial Interface Assigned to” Group ..................................... 135
“Assign Owner of Serial Interface (Active after Next
Controller Reboot)” Group ..................................................... 135
“Configuration of Service Interface” Page .................................. 136
“Service Interface assigned to” Group .................................... 136
“Assign Owner of Service Interface (enabled after next
controller reboot)” Group........................................................ 136
“Reboot Controller” Page ............................................................ 137
“Reboot Controller” Group ..................................................... 137
“Firmware Back-up” Page ........................................................... 138
“Firmware Restore” Page ............................................................ 139
“System Partition” Page .............................................................. 140
“Current Active Partition” Group ........................................... 140
“Set Inactive Partition Active” Group .................................... 140
“Mass Storage” Page ................................................................... 141
“<Device Name>” Group(s) ................................................... 141
7.8.1.14.1
7.8.1.15
7.8.1.15.1
7.8.1.16
7.8.1.16.1
7.8.1.16.2
7.8.1.17
7.8.1.17.1
7.8.1.17.2
7.8.1.18
7.8.1.18.1
7.8.1.19
7.8.1.20
7.8.1.21
7.8.1.21.1
7.8.1.21.2
7.8.1.22
7.8.1.22.1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table of Contents
7
7.8.1.22.2
“<Device Name> - FAT Format” Group(s) ............................ 141
7.8.1.23
“Software Uploads” Page ............................................................ 142
7.8.1.23.1
“Upload New Software” Group .............................................. 142
7.8.1.23.2
“Activate New Software” Group ............................................ 142
7.8.1.24
“Configuration of Network Services” Page ................................. 143
7.8.1.24.1
“Telnet” Group ........................................................................ 143
7.8.1.24.2
“FTP” Group ........................................................................... 143
7.8.1.24.3
“FTPS” Group ......................................................................... 143
7.8.1.24.4
“HTTP” Group ........................................................................ 143
7.8.1.24.5
“HTTPS” Group ...................................................................... 144
7.8.1.24.6
“I/O-CHECK” Group .............................................................. 144
7.8.1.25
“Configuration of NTP Client” Page ........................................... 145
7.8.1.25.1
“NTP Client Configuration” Group ........................................ 145
7.8.1.25.2
“NTP Single Request” Group ................................................. 145
7.8.1.26
“Configuration of PLC Runtime Services” Page......................... 146
7.8.1.26.1
“General Configuration” Group .............................................. 146
7.8.1.26.2
“CODESYS 2” Group ............................................................. 146
7.8.1.26.3
“e!RUNTIME” Group............................................................. 146
7.8.1.27
“SSH Server Settings” Page ........................................................ 147
7.8.1.27.1
“SSH Server” Group ............................................................... 147
7.8.1.28
“TFTP Server” Page .................................................................... 148
7.8.1.28.1
“TFTP Server” Group ............................................................. 148
7.8.1.29
“DHCP Configuration” Page ....................................................... 149
7.8.1.29.1
“DHCP Configuration Xn” Group .......................................... 149
7.8.1.30
“Configuration of DNS Service” Page ........................................ 150
7.8.1.30.1
“DNS Service” Group ............................................................. 150
7.8.1.31
“MODBUS Services Configuration” Page .................................. 151
7.8.1.31.1
“MODBUS TCP” Group ........................................................ 151
7.8.1.31.2
“MODBUS UDP” Group ........................................................ 151
7.8.1.32
“Configuration of General SNMP Parameters” Page .................. 152
7.8.1.32.1
“General SNMP Configuration” Group .................................. 152
7.8.1.33
“Configuration of SNMP v1/v2c Parameters” Page .................... 153
7.8.1.33.1
“SNMP v1/v2c Manager Configuration” Group .................... 153
7.8.1.33.2
“Actually Configured Trap Receivers” Group(s) ................... 153
7.8.1.33.3
“Trap Receiver n” Group(s) .................................................... 154
7.8.1.33.4
“Add New Trap Receiver” Group ........................................... 154
7.8.1.34
“Configuration of SNMP v3 Users” Page ................................... 155
7.8.1.34.1
“Actually Configured v3 Users” Group(s).............................. 155
7.8.1.34.2
“v3 User n” Group(s) .............................................................. 155
7.8.1.34.3
“Add New v3 User” Group ..................................................... 156
7.8.1.35
“Diagnostic Information” Page.................................................... 157
7.8.1.36
“Configuration of OpenVPN and IPsec” Page ............................ 158
7.8.1.36.1
“OpenVPN” Group ................................................................. 158
7.8.1.36.2
“IPsec” Group ......................................................................... 158
7.8.1.36.3
“Certificate Upload” Group .................................................... 159
7.8.1.36.4
“Certificate List” Group .......................................................... 159
7.8.1.36.5
“Private Key List” Group ........................................................ 159
7.8.2
Configuration using a Terminal Program (CBM) ............................ 160
7.8.2.1
CBM Menu Structure Overview .................................................. 160
7.8.2.2
“Information” Menu .................................................................... 163
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
8
Table of Contents
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.2.2.1
7.8.2.2.2
7.8.2.3
7.8.2.3.1
7.8.2.3.2
7.8.2.3.3
7.8.2.3.4
7.8.2.3.5
7.8.2.3.6
7.8.2.3.7
7.8.2.3.8
7.8.2.3.9
7.8.2.3.10
“Information” > “Controller Details” Submenu ..................... 163
“Information” > “Network Details” Submenu ........................ 164
“PLC Runtime” Menu ................................................................. 165
“PLC Runtime” > “Information” Submenu ............................ 165
“Information” > “Runtime Version” Submenu ....................... 166
“Information” > “Webserver Version” Submenu ................... 166
“Information” > “State” Submenu .......................................... 166
“Information” > “Number of Tasks” Submenu ...................... 167
“Information” > “Project Details” Submenu .......................... 167
“Information” > “Tasks” Submenu ......................................... 167
“Tasks” > “Task n” Submenu ................................................. 168
“PLC Runtime” > “General Configuration” Submenu ........... 168
“General Configuration” > “PLC Runtime Version”
Submenu.................................................................................. 169
“General Configuration” > “Home Dir On SD Card”
Submenu.................................................................................. 169
“PLC Runtime” > “WebVisu” Submenu ................................ 170
“Networking” Menu .................................................................... 171
“Networking” > “Host/Domain Name” Submenu .................. 171
“Host/Domain Name” > “Hostname” Submenu ..................... 172
“Host/Domain Name” > “Domain Name” Submenu.............. 172
“Networking” > “TCP/IP” Submenu ...................................... 172
“TCP/IP” > “IP Address” Submenu........................................ 173
“IP Address” > “Xn“ Submenu ............................................... 173
“TCP/IP” > “Default Gateway” Submenu .............................. 174
“Default Gateway” > “Default Gateway n” Submenu ............ 174
“TCP/IP” > “DNS Server” Submenu ...................................... 175
“Networking” > “Ethernet” Submenu..................................... 175
“Ethernet” > “Switch Configuration” Submenu ..................... 176
“Ethernet” > “Ethernet Ports” Submenu ................................. 176
“Ethernet Ports” > “Interface Xn” Submenu .......................... 177
“Firewall” Menu .......................................................................... 178
“Firewall” > “General Configuration” Submenu .................... 179
“General Configuration” > “Interface xxx” Submenu ............ 180
“Firewall” > “MAC Address Filter” Submenu ....................... 181
“MAC Address Filter” > “MAC address filter whitelist”
Submenu.................................................................................. 182
“MAC address filter whitelist” > “Add new / No (n)”
Submenu.................................................................................. 182
“Firewall” > “User Filter” Submenu ....................................... 183
“User Filter” > “Add New / No (n)” Submenu ....................... 184
“Clock” Menu .............................................................................. 185
“Administration” Menu ............................................................... 186
“Administration” > “Create Image” Submenu ....................... 187
“Administration” > “Users” Submenu .................................... 187
“Package Server” Menu ............................................................... 188
“Package Server” > “Firmware Backup” Submenu ................ 188
“Firmware Backup” > “Auto Update Feature” Submenu ....... 189
“Firmware Backup” > “Destination” Submenu ...................... 189
“Package Server” > “Firmware Restore” Submenu ................ 190
7.8.2.3.11
7.8.2.3.12
7.8.2.4
7.8.2.4.1
7.8.2.4.2
7.8.2.4.3
7.8.2.4.4
7.8.2.4.5
7.8.2.4.6
7.8.2.4.7
7.8.2.4.8
7.8.2.4.9
7.8.2.4.10
7.8.2.4.11
7.8.2.4.12
7.8.2.4.13
7.8.2.5
7.8.2.5.1
7.8.2.5.2
7.8.2.5.3
7.8.2.5.4
7.8.2.5.5
7.8.2.5.6
7.8.2.5.7
7.8.2.6
7.8.2.7
7.8.2.7.1
7.8.2.7.2
7.8.2.8
7.8.2.8.1
7.8.2.8.2
7.8.2.8.3
7.8.2.8.4
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table of Contents
9
7.8.2.8.5
7.8.2.8.6
7.8.2.9
7.8.2.9.1
7.8.2.10
7.8.2.11
7.8.2.11.1
7.8.2.11.2
7.8.2.11.3
7.8.2.11.4
7.8.2.11.5
7.8.2.11.6
7.8.2.11.7
7.8.2.11.8
7.8.2.11.9
7.8.2.11.10
7.8.2.11.11
7.8.2.11.12
7.8.2.11.13
7.8.2.11.14
7.8.2.11.15
7.8.2.11.16
7.8.2.11.17
7.8.2.11.18
7.8.2.12
7.8.2.12.1
7.8.2.12.2
“Firmware Restore” > “Select Package” Submenu ................ 190
“Package Server” > “System Partition” Submenu .................. 191
“Mass Storage” Menu .................................................................. 192
“Mass Storage” > “SD Card” Submenu .................................. 192
“Software Uploads” Menu ........................................................... 193
“Ports and Services” Menu .......................................................... 194
“Ports and Services” > “Telnet” Submenu ............................. 195
“Ports and Services” > “FTP” Submenu ................................. 195
“Ports and Services” > “FTPS” Submenu............................... 196
“Ports and Services” > “HTTP” Submenu .............................. 196
“Ports and Services” > “HTTPS” Submenu ........................... 197
“Ports and Services” > “NTP” Submenu ................................ 197
“Ports and Services” > “SSH” Submenu ................................ 198
“Ports and Services” > “TFTP” Submenu .............................. 198
“Ports and Services” > “DHCPD” Submenu .......................... 199
“DHCPD” > “Xn” Submenu ................................................... 199
“Ports and Services” > “DNS” Submenu ................................ 200
“Ports and Services” > “IOCHECK PORT” Submenu........... 201
“Ports and Services” > “Modbus TCP” Submenu .................. 201
“Ports and Services” > “Modbus UDP” Submenu.................. 202
“Ports and Services” > “PLC Runtime Services” Submenu ... 202
“PLC Runtime Services” > “CODESYS 2” Submenu ........... 203
“PLC Runtime Services” > “e!RUNTIME” Submenu ........... 204
“…” > “Firewall Status” Submenu ......................................... 205
“SNMP” Menu............................................................................. 206
“SNMP” > “General SNMP Configuration” Submenu .......... 206
“SNMP” > “SNMP v1/v2c Manager Configuration”
Submenu.................................................................................. 207
7.8.2.12.3
“SNMP” > “SNMP v1/v2c Trap Receiver Configuration”
Submenu.................................................................................. 207
7.8.2.12.4
“SNMP” > “SNMP v3 Configuration” Submenu ................... 208
7.8.2.12.5
“SNMP” > “(Secure)SNMP firewalling” Submenu ............... 209
7.8.3
Configuration using “WAGO ETHERNET Settings” ..................... 210
7.8.3.1
Identification Tab......................................................................... 212
7.8.3.2
Network Tab ................................................................................ 213
7.8.3.3
Protocol Tab................................................................................. 215
7.8.3.4
Status Tab .................................................................................... 216
8
Run-time System CODESYS 2.3 ............................................................ 217
8.1
Installing the CODESYS 2.3 Programming System ............................. 217
8.2
First Program with CODESYS 2.3 ....................................................... 217
8.2.1
Start the CODESYS Programming System ...................................... 217
8.2.2
Creating a Project and Selecting a Target System............................ 217
8.2.3
Creating the PLC Configuration....................................................... 219
8.2.4
Editing the Program Function Block ................................................ 226
8.2.5
Loading and Running the PLC Program in the Fieldbus Controller
(ETHERNET) ................................................................................... 228
8.2.6
Creating a Boot Project .................................................................... 230
8.3
Syntax of Logical Addresses ................................................................. 230
8.4
Creating Tasks ....................................................................................... 231
8.4.1
Cyclic Tasks ..................................................................................... 234
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
10
Table of Contents
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
8.4.2
8.5
8.5.1
8.6
8.6.1
8.6.2
8.7
Freewheeling Tasks .......................................................................... 235
System Events ....................................................................................... 235
Creating an Event Handler ............................................................... 238
Process Images ...................................................................................... 241
Process Images for I/O Modules Connected to the Controller ......... 242
Process Image for Slaves Connected to the Fieldbus ....................... 243
Access to Process Images of the Input and Output Data via
CODESYS 2.3....................................................................................... 243
8.8
Addressing Example ............................................................................. 244
8.9
Internal Data Bus Synchronization ....................................................... 245
8.9.1
Case 1: CODESYS Task Interval Set Smaller than the I/O
Module Cycle ................................................................................... 246
8.9.2
Case 2: CODESYS Task Interval Smaller than Twice the Internal
Data Bus Cycle ................................................................................. 247
8.9.3
Case 3: CODESYS Task Interval Greater than Twice the
Internal Data Buc Cycle ................................................................... 248
8.9.4
Case 4: CODESYS Task Interval Greater than 10 ms ..................... 249
8.9.5
Internal Data Bus Configuration ...................................................... 250
8.9.5.1
Effect of Update Mode on CODESYS Tasks .............................. 251
8.9.5.1.1
Asynchronous Update Mode ................................................... 251
8.9.5.1.2
Synchronous Update Mode ..................................................... 252
8.10
Memory Settings in CODESYS ............................................................ 252
8.10.1
Program Memory.............................................................................. 252
8.10.2
Data Memory and Function Block Limitation ................................. 253
8.10.3
Remanent Memory ........................................................................... 254
8.11
CODESYS Visualization ...................................................................... 255
8.11.1
Limits of CODESYS Visualization .................................................. 258
8.11.2
Eliminating Errors in CODESYS Web Visualization ...................... 260
8.11.3
FAQs about CODESYS Web Visualization..................................... 261
9
e!RUNTIME Runtime Environment ...................................................... 263
9.1
General Notes ........................................................................................ 263
9.2
CODESYS V3 Priorities ....................................................................... 264
9.3
Memory Spaces under e!RUNTIME ..................................................... 265
9.3.1
Program and Data Memory .............................................................. 265
9.3.2
Function Block Limitation ............................................................... 265
9.3.3
Remanent Memory ........................................................................... 265
10 MODBUS – CODESYS 2 ........................................................................ 266
10.1
General .................................................................................................. 266
10.2
Features ................................................................................................. 266
10.3
Configuration ........................................................................................ 267
10.3.1
MODBUS Settings ........................................................................... 268
10.3.2
MODBUS TCP Settings ................................................................... 269
10.3.3
MODBUS UDP Settings .................................................................. 269
10.3.4
MODBUS RTU Settings .................................................................. 269
10.4
Data Exchange ...................................................................................... 272
10.4.1
Process Image ................................................................................... 273
10.4.2
Flag Area .......................................................................................... 274
10.4.3
MODBUS Registers ......................................................................... 275
10.4.4
MODBUS Mapping.......................................................................... 275
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
10.4.4.1
10.4.4.2
10.4.4.3
10.4.4.4
10.5
10.5.1
10.5.1.1
10.5.1.2
10.5.1.3
10.5.1.4
10.5.2
10.5.2.1
10.5.2.2
10.5.2.3
10.5.2.4
10.5.2.5
10.5.3
10.5.4
10.5.4.1
10.5.4.2
10.5.4.3
10.5.4.4
10.5.5
10.5.6
10.5.6.1
10.5.6.2
10.5.6.3
10.5.6.4
10.5.6.5
10.5.6.6
10.6
10.6.1
10.6.2
10.6.3
Table of Contents
11
MODBUS Mapping for Write Bit Services FC1, FC2 ................ 275
MODBUS Mapping for Write Bit Services FC5, FC15 .............. 276
MODBUS Mapping for Read Register Services FC3, FC4,
FC23 ............................................................................................ 277
MODBUS Mapping for Write Register Services FC6, FC16,
FC22, FC23.................................................................................. 279
WAGO MODBUS Register .................................................................. 281
Process Image Properties .................................................................. 282
Register 0x1022 – Number of Registers in the MODBUS
Input Process Image ..................................................................... 282
Register 0x1023 – Number of Registers in the MODBUS
Output Process Image .................................................................. 282
Register 0x1024 – Number of Bits in the MODBUS Input
Process Image .............................................................................. 282
Register 0x1025 – Number of Bits in the MODBUS Output
Process Image .............................................................................. 282
Network Configuration ..................................................................... 283
Register 0x1028 – IP Configuration ............................................ 283
Register 0x102A – Number of Established TCP Connections .... 283
Register 0x1030 – MODBUS TCP Socket Timeout ................... 283
Register 0x1031 – MAC Address for ETHERNET-Interface 1
(eth0) ............................................................................................ 283
Register 0x1037 - MODBUS TCP Response Delay ................... 283
PLC Status Register .......................................................................... 284
MODBUS Watchdog........................................................................ 284
Register 0x1100 – Watchdog Command ..................................... 284
Register 0x1101 – Watchdog Status ............................................ 286
Register 0x1102 – Watchdog Timeout ........................................ 286
Register 0x1103 – Watchdog Config .......................................... 287
MODBUS Constants Register .......................................................... 287
Electronic Nameplate ....................................................................... 288
Register 0x2010 – Revision (Firmware Index) ........................... 288
Register 0x2011 – Series Designator ........................................... 288
Register 0x2012 – Device ID ...................................................... 288
Register 0x2013 – Major Firmware Version ............................... 288
Register 0x2014 – Minor Firmware Version ............................... 288
Register 0x2015 – MBS Version ................................................. 288
Diagnostics ............................................................................................ 289
Diagnostics for the MODBUS Master ............................................. 289
Diagnostics for the Runtime System ................................................ 289
Diagnostics for the Error Server ....................................................... 289
11 MODBUS – e!RUNTIME ........................................................................ 292
11.1
MODBUS Address Overview ............................................................... 292
11.2
MODBUS Registers .............................................................................. 293
11.2.1
MODBUS Watchdog........................................................................ 295
11.2.1.1
Watchdog Command Register ..................................................... 295
11.2.1.2
Watchdog Timeout Register ........................................................ 295
11.2.1.3
Watchdog Status Register ............................................................ 296
11.2.1.4
Watchdog Config Register .......................................................... 297
11.2.1.5
MODBUS TCP Connection Watchdog Register ......................... 298
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
12
Table of Contents
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
11.2.2
Status Registers ................................................................................ 299
11.2.2.1
PLC Status Register ..................................................................... 299
11.2.3
Electronic Nameplate ....................................................................... 299
11.2.3.1
Order Number .............................................................................. 299
11.2.3.2
Firmware Version ........................................................................ 299
11.2.3.3
Hardware Version ........................................................................ 299
11.2.3.4
Firmware Loader/Boot Loader .................................................... 299
11.2.4
MODBUS Process Image Version ................................................... 299
11.2.5
MODBUS Process Image Registers ................................................. 300
11.2.6
Constants Registers .......................................................................... 300
11.2.7
Live Register .................................................................................... 300
11.3
Estimating the MODBUS Master CPU Load ....................................... 301
11.4
Estimating the MODBUS Master CPU Load ....................................... 302
12 Diagnostics ................................................................................................ 303
12.1
Operating and Status Messages ............................................................. 303
12.1.1
Power Supply Indicating Elements .................................................. 303
12.1.2
Fieldbus/System Indicating Elements .............................................. 304
12.2
Diagnostics Messages (I/O LED).......................................................... 308
12.2.1
Flashing Sequence ............................................................................ 308
12.2.2
Example of a Diagnostics Message Indicated by a Blink Code ....... 310
12.2.3
Meaning of Blink Codes and Procedures for Troubleshooting ........ 311
13 Service ....................................................................................................... 316
13.1
Inserting and Removing the Memory Card ........................................... 316
13.1.1
Inserting the Memory Card .............................................................. 316
13.1.2
Removing the Memory Card ............................................................ 316
13.2
Firmware Changes ................................................................................ 317
13.2.1
Perform Firmware Upgrade .............................................................. 317
13.2.2
Perform Firmware Downgrade ......................................................... 318
13.2.3
Factory Reset .................................................................................... 319
14 Removal .................................................................................................... 320
14.1
Removing Devices ................................................................................ 320
14.1.1
Removing the Fieldbus Coupler/Controller ..................................... 320
14.1.2
Removing the I/O Module ................................................................ 321
15 Use in Hazardous Environments ............................................................ 322
15.1
Marking Configuration Examples ......................................................... 323
15.1.1
Marking for Europe According to ATEX and IEC-Ex .................... 323
15.1.2
Marking for America According to NEC 500 .................................. 328
15.2
Installation Regulations ......................................................................... 329
15.2.1
Special Conditions for Safe Use
(TÜV 14 ATEX 148929 X) .............................................................. 330
15.2.2
Special Conditions for Safe Use
(ATEX Certificate TÜV 12 ATEX 106032 X) ................................ 331
15.2.3
Special Conditions for Safe Use
(IEC-Ex Certificate TUN 14.0035X) ............................................... 332
15.2.4
Special Conditions for Safe Use
(IEC-Ex Certificate IECEx TUN 12.0039 X) .................................. 333
15.2.5
Special Conditions for Safe Use according to
ANSI/ISA 12.12.01 .......................................................................... 334
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table of Contents
13
16 Appendix ................................................................................................... 335
16.1
Structure of Process Data for the I/O Modules ..................................... 335
16.1.1
Digital Input Modules....................................................................... 336
16.1.1.1
1 Channel Digital Input Module with Diagnostics ...................... 336
16.1.1.2
2 Channel Digital Input Modules ................................................ 336
16.1.1.3
2 Channel Digital Input Module with Diagnostics ...................... 336
16.1.1.4
2 Channel Digital Input Module with Diagnostics and Output
Process Data................................................................................. 337
16.1.1.5
4 Channel Digital Input Modules ................................................ 337
16.1.1.6
8 Channel Digital Input Modules ................................................ 337
16.1.1.7
8 Channel Digital Input Module PTC with Diagnostics and
Output Process Data .................................................................... 338
16.1.1.8
16 Channel Digital Input Modules .............................................. 338
16.1.2
Digital Output Modules .................................................................... 339
16.1.2.1
1 Channel Digital Output Module with Input Process Data ........ 339
16.1.2.2
2 Channel Digital Output Modules .............................................. 339
16.1.2.3
2 Channel Digital Input Modules with Diagnostics and Input
Process Data................................................................................. 340
16.1.2.4
4 Channel Digital Output Modules .............................................. 341
16.1.2.5
4 Channel Digital Output Modules with Diagnostics and Input
Process Data................................................................................. 341
16.1.2.6
8 Channel Digital Output Module ............................................... 341
16.1.2.7
8 Channel Digital Output Modules with Diagnostics and Input
Process Data................................................................................. 342
16.1.2.8
16 Channel Digital Output Modules ............................................ 342
16.1.2.9
8 Channel Digital Input/Output Modules .................................... 343
16.1.3
Analog Input Modules ...................................................................... 344
16.1.3.1
1 Channel Analog Input Modules ................................................ 344
16.1.3.2
2 Channel Analog Input Modules ................................................ 344
16.1.3.3
4 Channel Analog Input Modules ................................................ 345
16.1.3.4
3-Phase Power Measurement Module ......................................... 346
16.1.3.5
8 Channel Analog Input Modules ................................................ 346
16.1.4
Analog Output Modules ................................................................... 347
16.1.4.1
2 Channel Analog Output Modules ............................................. 347
16.1.4.2
4 Channel Analog Output Modules ............................................. 347
16.1.5
Specialty Modules ............................................................................ 348
16.1.5.1
Counter Modules ......................................................................... 348
16.1.5.2
Pulse Width Modules ................................................................... 350
16.1.5.3
Serial Interface Modules with alternative Data Format ............... 350
16.1.5.4
Serial Interface Modules with Standard Data Format ................. 351
16.1.5.5
Data Exchange Module................................................................ 351
16.1.5.6
SSI Transmitter Interface Modules .............................................. 351
16.1.5.7
Incremental Encoder Interface Modules ...................................... 352
16.1.5.8
DC-Drive Controller .................................................................... 354
16.1.5.9
Stepper Controller ........................................................................ 355
16.1.5.10
RTC Module ................................................................................ 356
16.1.5.11
DALI/DSI Master Module ........................................................... 356
16.1.5.12
DALI Multi-Master Module ........................................................ 357
16.1.5.13
LON® FTT Module...................................................................... 359
16.1.5.14
EnOcean Radio Receiver ............................................................. 359
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
14
Table of Contents
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
16.1.5.15
MP Bus Master Module ............................................................... 359
16.1.5.16
Bluetooth® RF-Transceiver .......................................................... 360
16.1.5.17
Vibration Velocity/Bearing Condition Monitoring VIB I/O ....... 361
16.1.5.18
KNX/EIB/TP1 Module ................................................................ 361
16.1.5.19
AS-interface Master Module ....................................................... 362
16.1.6
System Modules ............................................................................... 364
16.1.6.1
System Modules with Diagnostics ............................................... 364
16.1.6.2
Binary Space Module .................................................................. 364
16.2
CODESYS 2 Libraries .......................................................................... 365
16.2.1
General Libraries .............................................................................. 365
16.2.1.1
CODESYS System Libraries ....................................................... 365
16.2.1.2
SysLibCom.lib ............................................................................. 366
16.2.1.3
SysLibFile.lib............................................................................... 366
16.2.1.4
SysLibFileAsync.lib .................................................................... 367
16.2.1.5
SysLibRtc.lib ............................................................................... 368
16.2.1.6
BusDiag.lib .................................................................................. 369
16.2.1.7
mod_com.lib ................................................................................ 369
16.2.1.8
SerComm.lib ................................................................................ 369
16.2.1.9
WagoConfigToolLIB.lib ............................................................. 370
16.2.1.10
WagoLibCpuUsage.lib ................................................................ 386
16.2.1.11
WagoLibDiagnosticIDs.lib .......................................................... 386
16.2.1.12
WagoLibLed.lib ........................................................................... 387
16.2.1.13
WagoLibNetSnmp.lib .................................................................. 387
16.2.1.14
WagoLibNetSnmpManager.lib .................................................... 387
16.2.1.15
WagoLibSSL.lib .......................................................................... 388
16.2.1.16
WagoLibTerminalDiag.lib........................................................... 388
16.3
Overview of Open Source Packages and Licenses ............................... 389
List of Figures .................................................................................................... 393
List of Tables ...................................................................................................... 396
=== Ende der Liste für T extmar ke Verzeic hnis_vor ne ===
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Notes about this Documentation
15
Pos : 7 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Ebene 1/Hinweis e z u dies er D okumentati on - Übersc hrift 1 @ 4\mod_1237987661750_21.doc x @ 29029 @ 1 @ 1
1
Notes about this Documentation
Pos : 8 /Alle Serien (Allgemeine M odul e)/Wi chtig e Erl äuter ung en/Sic her hei ts- und s onstige Hi nweise/Hinweis/Hi nweis : D okumentation aufbewahr en @ 4\mod_1237987339812_21.doc x @ 29026 @ @ 1
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation is
included, if necessary.
Pos : 9 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Ebene 2/Gültig kei tsbereic h - Übersc hrift 2 @ 12\mod_1338912448776_21.doc x @ 96469 @ 2 @ 1
1.1
Validity of this Documentation
Pos : 10 /Serie 750 ( WAGO-I/O-SYST EM)/Hi nweis e z ur D okumentati on/Gültigkeits bereic h/Gültig keits ber eich Dokumentation C ontroller 750- xxxx, ohne Vari antenangabe @ 19\mod_1402575362855_21.doc x @ 155768 @ @ 1
This documentation is only applicable to the controller “PFC200 CS 2ETH RS
/XTR” (750-8202/040-000).
Pos : 11 /All e Seri en (Allgemei ne Module)/R ec htlic hes , Allgemei nes /Gültig keitsbereic h D okumentati on Ergänz ung " ab <F W/H W/SW-Version>" @ 20\mod_1407749774742_21.doc x @ 161508 @ @ 1
This documentation is only applicable from FW Version 02.04.22(06).
Pos : 12 /Serie 750 ( WAGO-I/O-SYST EM)/Hi nweis e z ur D okumentati on/Hi nweise/Ac htung: Hinweis z ur D okumentati on Koppl er/Contr oller 750- xxx/040- 000 @ 18\mod_1394111960171_21.doc x @ 147458 @ @ 1
The device PFC200 CS 2ETH RS /XTR 750-8202/040-000 shall only be installed
and operated according to the instructions in this manual and the system
description for the WAGO-I/O-SYSTEM 750 XTR.
Consider power layout of the WAGO-I/O-SYSTEM 750 XTR!
In addition to these operating instructions, you will also need the system
description for the WAGO-I/O-SYSTEM 750 XTR, which can be downloaded at
www.wago.com. There, you can obtain important information including
information on electrical isolation, system power and supply specifications.
Pos : 13.1 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/Ebene 2/Ur hebersc hutz - Ü bersc hrift 2 @ 23\mod_1435647042188_21.doc x @ 184808 @ 2 @ 1
1.2
Copyright
Pos : 13.2 /All e Seri en ( Allgemei ne Module)/R ec htliches , Allgemei nes /Urhebersc hutz ausführlich @ 4\mod_1235565145234_21.doc x @ 27691 @ @ 1
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos : 13.3 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
16
Notes about this Documentation
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 13.4 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/N eue Ü berschriften/Ebene 2Symbol e - Ü bersc hrift 2 @ 13\mod_1351068042408_21.doc x @ 105270 @ 2 @ 1
1.3
Symbols
Pos : 13.5.1 /All e Serien ( Allgemei ne Module)/Sicherheits- und sons tige Hi nweis e/Gefahr/Gefahr: _War nung vor Pers onenschäden allgemei n_ - Erläuter ung @ 13\mod_1343309450020_21.doc x @ 101029 @ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos : 13.5.2 /All e Serien ( Allgemei ne Module)/Sicherheits- und sons tige Hi nweis e/Gefahr/Gefahr: _War nung vor Pers onenschäden durch el ektrisc hen Strom_ - Erläuterung @ 13\mod_1343309694914_21.doc x @ 101030 @ @ 1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos : 13.5.3 /All e Serien ( Allgemei ne Module)/Sicherheits- und sons tige Hi nweis e/Warnung/Warnung: _Warnung vor Personensc häden allgemei n_ - Erläuterung @ 13\mod_1343309877041_21.doc x @ 101035 @ @ 1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos : 13.5.4 /All e Serien ( Allgemei ne Module)/Sicherheits- und sons tige Hi nweis e/Vorsic ht/Vorsicht: _War nung vor Pers onensc häden allgemein_ - Erläuterung @ 13\mod_1343310028762_21.doc x @ 101038 @ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos : 13.5.5 /All e Serien ( Allgemei ne Module)/Sicherheits- und sons tige Hi nweis e/Ac htung/Achtung: _War nung vor Sac hsc häden allgemein_ - Erläuterung @ 13\mod_1343310134623_21.doc x @ 101041 @ @ 1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos : 13.5.6 /All e Serien ( Allgemei ne Module)/Sicherheits- und sons tige Hi nweis e/Ac htung/Achtung: _War nung vor Sac hsc häden durc h elektrostatis che Aufladung_ - Erl äuter ung @ 13\mod_1343310227702_21.doc x @ 101044 @ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos : 13.5.7 /All e Serien ( Allgemei ne Module)/Sicherheits- und sons tige Hi nweis e/Hi nweis /Hinweis: _Wic htiger Hi nweis allgemein_ - Erläuterung @ 13\mod_1343310326906_21.doc x @ 101047 @ @ 1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos : 13.5.8 /All e Serien ( Allgemei ne Module)/Sicherheits- und sons tige Hi nweis e/Infor mation/Infor mation: _Weiter e Infor mation allgemei n_ - Erl äuter ung @ 13\mod_1343310439814_21.doc x @ 101051 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Notes about this Documentation
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos : 13.6 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
17
18
Notes about this Documentation
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 13.7 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/Ebene 2/D arstellung der Z ahlens ys teme - Ü bers chrift 2 @ 23\mod_1435647128078_21.doc x @ 184811 @ 2 @ 1
1.4
Number Notation
Pos : 13.8 /All e Seri en ( Allgemei ne Module)/R ec htliches , Allgemei nes /Zahlens ysteme @ 3\mod_1221059454015_21.doc x @ 21711 @ @ 1
Table 1: Number Notation
Number Code
Decimal
Hexadecimal
Binary
Example
100
0x64
'100'
'0110.0100'
Note
Normal notation
C notation
In quotation marks, nibble separated with
dots (.)
Pos : 13.9 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/Ebene 2/Sc hriftkonventi onen - Ü bersc hrift 2 @ 23\mod_1435647186005_21.doc x @ 184814 @ 2 @ 1
1.5
Font Conventions
Pos : 13.10 /Alle Serien (Allgemeine M odul e)/Rechtliches, Allgemeines/Sc hriftkonventi onen @ 3\mod_1221059521437_21.doc x @ 21714 @ @ 1
Table 2: Font Conventions
Font Type Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu items are marked in bold letters.
Menu
e.g.: Save
A greater-than sign between two names means the selection of a
>
menu item from a menu.
e.g.: File > New
Designation of input or optional fields are marked in bold letters,
Input
e.g.: Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
Pushbuttons in dialog boxes are marked with bold letters in square
[Button]
brackets.
e.g.: [Input]
Keys are marked with bold letters in square brackets.
[Key]
e.g.: [F5]
Pos : 14 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Important Notes
19
Pos : 15 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 1/Wic htige Erl äuter ungen - Übersc hrift 1 @ 4\mod_1241428899156_21.doc x @ 32170 @ 1 @ 1
2
Important Notes
Pos : 16.1 /All e Seri en ( Allgemei ne Module)/R ec htliches , Allgemei nes Wic htige Erläuterungen - Einl eitung @ 3\mod_1221059818031_21.doc x @ 21717 @ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos : 16.2 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/N eue Ü berschriften/Ebene 2R ec htlic he Grundlagen - Ü berschrift 2 @ 3\mod_1221060626343_21.doc x @ 21726 @ 2 @ 1
2.1
Legal Bases
Pos : 16.3 /All e Seri en ( Allgemei ne Module)/R ec htliches , Allgemei nes Änderungs vor behalt - Ü berschrift 3 und Inhalt @ 3\mod_1221060036484_21.doc x @ 21720 @ 3 @ 1
2.1.1
Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications that serve to increase the efficiency of technical
progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from
the granting of patents or from the legal protection of utility patents. Third-party
products are always mentioned without any reference to patent rights. Thus, the
existence of such rights cannot be excluded.
Pos : 16.4 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Pers onalqualifi kationPers onalqualifi kation 750- xxxx - Ü bersc hrift 3 und Inhalt @ 3\mod_1224061208046_21.doc x @ 24063 @ 3 @ 1
2.1.2
Personnel Qualifications
All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos : 16.5 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Bes timmungsgemäß e Verwendung Bes ti mmungsgemäße Verwendung 750-xxxx - Ü berschrift 3 und Inhal t @ 3\mod_1224064151234_21.doc x @ 24070 @ 3 @ 1
2.1.3
Use of the WAGO-I/O-SYSTEM 750 in Compliance with
Underlying Provisions
Fieldbus couplers, fieldbus controllers and I/O modules found in the modular
WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and
transmit them to actuators or higher-level control systems. Using programmable
controllers, the signals can also be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO-I/O-SYSTEM 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information
in the section “Device Description” > “Standards and Guidelines” in the manual
for the used fieldbus coupler/controller.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
20
Important Notes
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appropriate housing (per 2014/34/EU) is required when operating the WAGOI/O-SYSTEM 750 in hazardous environments. Please note that a prototype test
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.
Pos : 16.6 /All e Seri en ( Allgemei ne Module)/R ec htliches , Allgemei nesT ec hnis cher Z ustand der Geräte - Übersc hrift 3 und Inhalt @ 3\mod_1221060446109_21.doc x @ 21723 @ 3 @ 1
2.1.4
Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. WAGO
Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of
changes in hardware or software as well as to non-compliant usage of devices.
Please send your request for modified and new hardware or software
configurations directly to WAGO Kontakttechnik GmbH & Co. KG.
Pos : 16.7 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Important Notes
21
Pos : 16.8 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/N eue Ü berschriften/Ebene 2Sicher heits hi nweis e - Ü berschrift 2 @ 6\mod_1260180299987_21.doc x @ 46724 @ 2 @ 1
2.2
Safety Advice (Precautions)
Pos : 16.9 /All e Seri en ( Allgemei ne Module)/Sicherheits- und s ons tige Hi nweis e/Einl eitung Sicherheits hinweis e H ardware @ 6\mod_1260180170493_21.doc x @ 46720 @ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos : 16.10.1 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits hinweise/Gefahr /Gefahr: Nicht an Geräten unter Spannung ar beiten! @ 6\mod_1260180365327_21.doc x @ 46727 @ @ 1
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos : 16.10.2 /Serie 750 ( WAGO-I/O- SYST EM)/Wic htig e Erl äuter ung en/Sic her hei ts- und s onstige Hi nweise/Gefahr/Gefahr: Ei nbau 0750- xxxx nur i n Gehäus en, Sc hränken oder el ektrisc hen Betriebsräumen! @ 6\mod_1260180556692_21.doc x @ 46731 @ @ 1
Install the device only in appropriate housings, cabinets or in electrical
operation rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Pos : 16.10.3 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits hinweise/Gefahr /Gefahr: Unfall verhütungs vorsc hriften beachten! @ 6\mod_1260180657000_21.doc x @ 46735 @ @ 1
Pos : 16.10.4 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits hinweise/Gefahr /Gefahr: Auf normg erec hten Ansc hluss ac hten! @ 6\mod_1260180753479_21.doc x @ 46739 @ @ 1
Pos : 16.11 /Alle Serien (Allgemeine M odul e)/Sic herheits- und sonstige Hinweis e/Vorsic ht/Vorsic ht: H eiße Oberfl äc he allgemein @ 6\mod_1264428115588_21.doc x @ 48610 @ @ 1
Hot surface!
The surface of the housing can become hot during operation. If the device was
operated at high ambient temperatures, allow it to cool off before touching it.
Pos : 16.12.1 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits hinweise/Ac htung/Ac htung: Defekte oder besc hädigte Ger äte aus tausc hen! @ 6\mod_1260180857358_21.doc x @ 46743 @ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
Pos : 16.12.2 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits hinweise/Ac htung/Ac htung: Geräte vor kriec henden und is olier enden Stoffen schützen! @ 6\mod_1260181036216_21.doc x @ 46747 @ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for handling
devices/modules.
Pos : 16.12.3 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits hinweise/Ac htung/Ac htung: Rei nigung nur mit zul ässigen M aterialien! @ 6\mod_1260181203293_21.doc x @ 46751 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
22
Important Notes
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Clean only with permitted materials!
Clean soiled contacts using oil-free compressed air or with ethyl alcohol and
leather cloths.
Pos : 16.12.4 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits hinweise/Ac htung/Ac htung: Kei n Kontakts pray verwenden! @ 6\mod_1260181290808_21.doc x @ 46755 @ @ 1
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos : 16.12.5 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits hinweise/Ac htung/Ac htung: Verpol ung ver mei den! @ 6\mod_1260184045744_21.doc x @ 46767 @ @ 1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos : 16.12.6 /Alle Serien (Allgemeine D okumente) (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits hinweise/Ac htung/Ac htung: El ektr ostatisc he Entl adung vermeiden! @ 6\mod_1260181364729_21.doc x @ 46759 @ @ 1
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.
Pos : 16.13 /Serie 750 ( WAGO-I/O-SYST EM)/Wichtig e Erl äuter ung en/Sic her hei ts- und s onstige Hinweise/Ac htung/Ac htung: XTR - Is olations prüfungen mit DC durchführen! @ 15\mod_1370843209441_21.doc x @ 122210 @ @ 1
Perform insulation tests with direct current (DC)!
Both the supply voltage and control voltage side are capacitively coupled to the
DIN rail. If the modules are mounted on the DIN rail, application of an AC
voltage between the two potentials can lead to the destruction of the device.
Use only direct current (DC) for insulation testing.
To avoid destroying the device, discharge the device completely before applying
the test voltage again.
Pos : 17 /All e Seri en (Allgemei ne Module)/Wic htige Erläuterungen/Sicherheits- und s ons tige Hi nweis e/Ac htung/Achtung: Nic ht in Tel ekommuni kationsnetzen eins etzen! (Zus atz RJ-45) @ 3\mod_1224065187468_21.doc x @ 24076 @ @ 1
Do not use in telecommunication circuits!
Only use devices equipped with ETHERNET or RJ-45 connectors in LANs.
Never connect these devices with telecommunication networks.
Pos : 18 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Important Notes
23
Pos : 19 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 2/Liz enzbedi ngungen der ei nges etzten Softwarepakete - Ü berschrift 2 @ 26\mod_1461574114408_21.doc x @ 209498 @ 2 @ 1
2.3
Licensing Terms of the Software Package Used
Pos : 20 /Serie 750 ( WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Lizenz beding ung en/Liz enzbedingungen der ei nges etz ten Softwarepakete 750- 8xxx @ 24\mod_1453106204507_21.doc x @ 198479 @ @ 1
The firmware for the “PFC200 CS 2ETH RS /XTR” controller (750-8202/040000) contains open source software.
A tabular list of software packages is provided in the appendix.
For licensing terms of the software packages, please see “Software Licenses for
Open Source Software in WAGO Components”, which is available to download
on the Internet at www.wago.com under “Technical Documentation”.
You can obtain the source code with licensing terms of the open source software
from WAGO Kontakttechnik GmbH & Co. KG on request. Send your request to
support@wago.com with the subject “Controller Board Support Package”.
Pos : 21 /All e Seri en (Allgemei ne Module)/R ec htlic hes , Allgemei nes /Spezielle Ei ns atz besti mmungen für ETHERN ET-Geräte - Übersc hrift 2 und Inhalt @ 12\mod_1336642945500_21.doc x @ 94792 @ 2 @ 1
2.4
Special Use Conditions for ETHERNET Devices
If not otherwise specified, ETHERNET devices are intended for use on local
networks. Please note the following when using ETHERNET devices in your
system:
•
Do not connect control components and control networks to an open
network such as the Internet or an office network. WAGO recommends
putting control components and control networks behind a firewall.
•
Limit physical and electronic access to all automation components to
authorized personnel only.
•
Change the default passwords before first use! This will reduce the risk of
unauthorized access to your system.
•
Regularly change the passwords used! This will reduce the risk of
unauthorized access to your system.
•
If remote access to control components and control networks is required,
use a Virtual Private Network (VPN).
•
Regularly perform threat analyses. You can check whether the measures
taken meet your security requirements.
•
Use “defense-in-depth” mechanisms in your system's security configuration
to restrict the access to and control of individual products and networks.
Pos : 22 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
24
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 23 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 1/Gerätebes chr eibung - Ü berschrift 1 @ 3\mod_1233756084656_21.doc x @ 27096 @ 1 @ 1
3
Device Description
Pos : 24.1.1 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ei nlei tung/Anwendung/F BK/PFC /Anwendung 750-8xxx @ 14\mod_1360300590437_21.doc x @ 111161 @ @ 1
The controller 750-8202/040-000(PFC200 CS 2ETH RS /XTR) is an automation
device that can perform control tasks of a PLC. It is suitable for mounting on a
DIN rail and stands out on account of its various interfaces.
This controller can be used for applications in mechanical and systems
engineering, in the processing industry and in building technology.
Pos : 24.1.2 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ei nlei tung/Anwendung/F BK/PFC /I/O-Besc hrei bung 750-82xx Bus klemmen XTR @ 22\mod_1426082837685_21.doc x @ 177425 @ @ 1
You can connect all available I/O modules of the WAGO-I/O-SYSTEM 750 XTR
to the controller, enabling it to internally process analog and digital signals from
the automation environment, or to supply these signals to other devices via one of
the available interfaces.
Pos : 24.1.3 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ei nlei tung/Anwendung/F BK/PFC /Automatisier ung 750-82xx, C ODESYS 2 und e!RUNTIME @ 20\mod_1406700911890_21.doc x @ 160562 @ @ 1
Automation tasks can be executed in all IEC 61131-3-compatible languages with
the WAGO-I/O-PRO or e!COCKPIT programming system, depending on the
runtime system set (CODESYS 2 or e!RUNTIME).
The implementation of the task processing in the runtime system for Linux® has
been optimized with real-time extensions in order to provide maximum
performance for automation tasks. Web visualization is also provided as
visualization in addition to the development environment.
Pos : 24.1.4 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ei nlei tung/Anwendung/F BK/PFC /Automatisier ung 750-8xxx, COD ESYS-Implementier ung @ 20\mod_1411375254147_21.doc x @ 164052 @ @ 1
Pos : 24.1.5 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ei nlei tung/Anwendung/F BK/PFC /Speic her 750-82xx - C OD ESYS 2 @ 16\mod_1376923205130_21.doc x @ 129248 @ @ 1
The controller provides a 16 Mbyte program memory, a 64 Mbyte data memory
and a 128 kbyte remanent memory (retain and flag variables) in an integrated
NVRAM for IEC-61131-3 programming on CODESYS applications.
Pos : 24.1.6 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ei nlei tung/Anwendung/F BK/PFC /I/O-Besc hrei bung 750-8xxx Ethernet @ 16\mod_1376923299385_21.doc x @ 129256 @ @ 1
</dg_
Two ETHERNET interfaces and an integrated, interruptible switch enable wiring
for:
•
In line topology with a common MAC address and IP address for both
interfaces.
•
Two separate networks with a common MAC address and an IP address for
each interface.
Both of these interfaces support:
•
10BASE-T / 100BASE-TX
•
Full/Half duplex
•
Autonegotiation
•
Auto-MDI(X) (automatic uplink and crossover switching)
Pos : 24.1.7 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ei nlei tung/Anwendung/F BK/PFC /I/O-Besc hrei bung 750-8xxx F eldbus Ei nlei tung + MOD BU S-TCP/UD P-Mas ter/Slave @ 16\mod_1379395320258_21.doc x @ 131640 @ @ 1
The following fieldbus circuits are implemented for exchange of process data:
•
MODBUS TCP Master/Slave
•
MODBUS UDP Master/Slave
Pos : 24.1.8 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ei nlei tung/Anwendung/F BK/PFC /I/O-Besc hrei bung 750-8xxx F eldbus Ergänz ung MODBU S-RTU-Mas ter /Sl ave (Seriell) @ 16\mod_1376923381720_21.doc x @ 129260 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
•
Device Description
25
MODBUS RTU Master/Slave (via RS-232 or RS-485)
Pos : 24.1.9 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ei nlei tung/Anwendung/F BK/PFC /Pr ozessabbild 750- 8xxx Klemmenbus @ 16\mod_1376923880648_21.doc x @ 129279 @ @ 1
In the controller, all input signals from the sensors are combined. After connecting
the controller, all of the I/O modules on the bus node are detected and a local
process image is created from these. Analog and specialty module data is sent via
words and/or bytes; digital data is sent bit by bit.
Pos : 24.1.10 /Serie 750 ( WAGO-I/O- SYST EM)/Pr ozessabbild M appi ng/PFC xxx/Hi nweis : Kei n dir ekter Z ugriff vom F eldbus auf das Pr ozes sabbild der Bus kl emmen! @ 16\mod_1379510128893_21.doc x @ 131836 @ @ 1
No direct access from fieldbus to the process image for I/O modules!
Any data that is required from the I/O module process image must be explicitly
mapped in the CODESYS program to the data in the fieldbus process image and
vice versa! Direct access is not possible!
Pos : 24.1.11 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Einl eitung/Anwendung/FBK/PFC/Konfigur ati on 750-82xx, Fel dbus konfiguration C ODESYS 2 und e!RUNTIME @ 20\mod_1406701023837_21.doc x @ 160566 @ @ 1
The fieldbus configuration can be defined with the WAGO-I/O-PRO or
e!COCKPIT controller configuration, depending on the set runtime system
(CODESYS 2 or e!RUNTIME).
Pos : 24.1.12 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Einl eitung/Anwendung/FBK/PFC/Konfigur ati on 750-82xx WBM @ 16\mod_1376923891727_21.doc x @ 129287 @ @ 1
A Web-based management system (WBM) is also available as a configuration aid.
This system includes various dynamic HTML pages from which, among other
things, information about configuration and the status of the controller can be
called up. The WBM is already stored in the device and is presented and operated
using an Internet browser. You can also save your own HTML pages in the
implemented file system, or call up programs directly.
In the controller's initial state, the installed firmware is based on Linux®, with
special real-time extensions of the RT-Preempt patch. In addition, the following
application programs are also installed on the controller, along with a number of
different auxiliary programs:
Pos : 24.1.13 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Einl eitung/Anwendung/FBK/PFC/Di enste 750-8xxx Standar d @ 16\mod_1376924023557_21.doc x @ 129295 @ @ 1
•
a SNMP server/client
•
a Telnet server
•
a FTP, FTPS server
•
a SSH server/client
•
a Web server
•
a NTP client
•
a BootP and DHCP client
Pos : 24.1.14 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Einl eitung/Anwendung/FBK/PFC/Di enste 750-8xxx DHC PD/DNS @ 20\mod_1407148877292_21.doc x @ 161056 @ @ 1
•
a DHCP server
•
a DNS server
Pos : 24.1.15 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Einl eitung/Anwendung/FBK/PFC/Di enste 750-82xx, COD ESYS - COD ESYS 2 und e!RUNTIME, ums chaltbar @ 20\mod_1406701158188_21.doc x @ 160570 @ @ 1
•
a CODESYS Runtime Environment (CODESYS 2 or e!RUNTIME,
selectable)
Pos : 24.1.16 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Einl eitung/Anwendung/FBK/PFC/Di enste 750-8xxx, C ODESYS - Erläuterung IEC-61131-3 @ 20\mod_1411374150744_21.doc x @ 164048 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
26
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Based on IEC-61131-3 programming, data processing takes place on site in the
controller. The logical process results can be output directly to the actuators or
transmitted via a connected fieldbus to the higher level controller.
Pos : 24.1.17 /Alle Serien (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits- und s onstige Hinweise/HinweisHinweis: Speicher kar te is t nicht i m Liefer umfang des C ontr ollers enthalten! @ 19\mod_1404994613368_21.doc x @ 158366 @ @ 1
Memory card is not included in the scope of delivery!
Note, the controller is delivered without memory card.
To use a memory card, you must order one separately. The controller can also be
operated without memory card expansion, the use of a memory card is optional.
Pos : 24.1.18 /Alle Serien (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits- und s onstige Hinweise/HinweisHinweis: Nur empfohl ene Speic her karte " SD" für C ontroller ver wenden! @ 19\mod_1404994303733_21.doc x @ 158348 @ @ 1
</dg_
Only use recommended memory cards!
Use only the SD memory card available from WAGO (item No. 758-879/000001) as it is suitable for industrial applications subjected to environmental
extremes and was developed for use in the controller.
Compatibility with other commercially available storage media cannot be
guaranteed.
Pos : 24.2 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Device Description
27
Pos : 24.3 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/N eue Ü berschriften/Ebene 2Ansicht - Ü bersc hrift 2 @ 4\mod_1240984217343_21.doc x @ 31958 @ 2 @ 1
3.1
View
Pos : 24.4.1 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ansic ht/PFC xxx/Abbildung enAnsicht 750-8202/0040-0000 - Abbildung XTR @ 22\mod_1426774094972_21.doc x @ 178172 @ @ 1
Figure 1: View
Pos : 24.4.2 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ansic ht/PFC xxx/Legendentabell enAnsicht 750-8xxx - Leg endentabell e, Kopfzeil e @ 12\mod_1341900885570_21.doc x @ 99349 @ @ 1
Table 3: Legend for Figure “View”
Item
Description
See section
Marking Options (Mini-WSB)
---
LED Indicators – Power Supply
“Indicating elements” >
“Indicating element power
supply”
Data contacts
“Connections” > “Data
contacts/Internal data bus”
Pos : 24.4.3 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ansic ht/PFC xxx/Legendentabell enAnsicht 750-8xxx - Leg endentabell e, T abell enz eile "Besc hriftungs möglichkeit" @ 16\mod_1378980504796_21.doc x @ 131310 @ @ 1
1
Pos : 24.4.4 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ansic ht/PFC xxx/Legendentabell enAnsicht 750-8xxx - Leg endentabell e, T abell enz eile "LED-Anz eigen Vers orgung" @ 16\mod_1378980510468_21.doc x @ 131314 @ @ 1
2
Pos : 24.4.5 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ansic ht/PFC xxx/Legendentabell enAnsicht 750-8xxx - Leg endentabell e, T abell enz eile "Datenkontakte" @ 16\mod_1378981072052_21.doc x @ 131326 @ @ 1
3
Pos : 24.4.6 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ansic ht/PFC xxx/Legendentabell enAnsicht 750-8xxx - Leg endentabell e, T abell enz eile "CAGE CLAMP®-Anschl üss e Vers orgung" @ 16\mod_1378981848985_21.doc x @ 131362 @ @ 1
4
CAGE CLAMP® Connections for Power “Connections” > “CAGE
Supply
CLAMP® connections”
Pos : 24.4.7 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ansic ht/PFC xxx/Legendentabell enAnsicht 750-8xxx - Leg endentabell e, T abell enz eile "Stec kpl atz für Speic her karte" @ 16\mod_1378981124990_21.doc x @ 131330 @ @ 1
5
Slot for memory card
“Memory card slot”
Power contacts for power supply of
down-circuit I/O modules
“Connections” > “Power
contacts/ Field-side supply”
Releasing strap
“Mounting” > “Inserting and
Removing Device”
Service Interface (behind the flap)
“Connections” > “Service
interface”
Mode selector switch
“Operating elements” >
“Mode selector switch”
ETHERNET Connections
“Connections” > “Network
connections ETHERNET –
X1, X2”
Pos : 24.4.8 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ansic ht/PFC xxx/Legendentabell enAnsicht 750-8xxx - Leg endentabell e, T abell enz eile "Leistungs kontakte Vers orgung" @ 16\mod_1378981982277_21.doc x @ 131366 @ @ 1
6
Pos : 24.4.9 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Ansic ht/PFC xxx/Legendentabell enAnsicht 750-8xxx - Leg endentabell e, T abell enz eile "Entrieg elungslas che" @ 16\mod_1378981225538_21.doc x @ 131334 @ @ 1
7
Pos : 24.4.10 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Ansicht/PFC xxx/LegendentabellenAnsic ht 750- 8xxx - Legendentabelle, T abellenz eile " Servi ce-Schnittstelle" @ 16\mod_1378981289554_21.doc x @ 131338 @ @ 1
8
Pos : 24.4.11 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Ansicht/PFC xxx/LegendentabellenAnsic ht 750- 8xxx - Legendentabelle, T abellenz eile " Betriebs artensc halter" @ 16\mod_1378981402384_21.doc x @ 131346 @ @ 1
9
Pos : 24.4.12 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Ansicht/PFC xxx/LegendentabellenAnsic ht 750- 8xxx - Legendentabelle, T abellenz eile " ETH ERNET- Ans chl üss e" @ 16\mod_1378981490682_21.doc x @ 131350 @ @ 1
10
Pos : 24.4.13 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Ansicht/PFC xxx/LegendentabellenAnsic ht 750- 8xxx - Legendentabelle, T abellenz eile " Verriegelungssc hei be" @ 16\mod_1378981361852_21.doc x @ 131342 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
28
Device Description
11
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Safe Locking Feature
“Mounting” > “Inserting and
Removing Device”
Serial interface
“Connections” >
“Communication port RS232/RS-485 – X3”
LED Indicators – System
“Indicating elements” >
“Indicating elements
Fieldbus/System”
Reset button (in hole)
“Operating elements” >
“Reset button”
Pos : 24.4.14 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Ansicht/PFC xxx/LegendentabellenAnsic ht 750- 8xxx - Legendentabelle, T abellenz eile " Serielle Sc hni ttstelle" @ 16\mod_1378982233870_21.doc x @ 131378 @ @ 1
12
Pos : 24.4.15 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Ansicht/PFC xxx/LegendentabellenAnsic ht 750- 8xxx - Legendentabelle, T abellenz eile " LED-Anzeigen Sys tem" @ 16\mod_1378981559105_21.doc x @ 131354 @ @ 1
13
Pos : 24.4.16 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Ansicht/PFC xxx/LegendentabellenAnsic ht 750- 8xxx - Legendentabelle, T abellenz eile "R es et-T aster" @ 16\mod_1378981664604_21.doc x @ 131358 @ @ 1
14
Pos : 24.4.17 /D okumentati on allgemein/Gli ederungsel emente/------Leerzeil e------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1
Pos : 24.5 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Device Description
29
Pos : 24.6 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/Ebene 2/Bedr uc kung - Ü berschrift 2 @ 4\mod_1241082409515_21.doc x @ 32035 @ 2 @ 1
3.2
Labeling
Pos : 24.7.1 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Bedruc kung/PFC xxxBedruc kung 750- 8xxx - Ei nleitung @ 4\mod_1242198457234_21.doc x @ 33046 @ @ 1
The front labeling includes:
Device designation
Name of the display elements, connections and control elements
Serial number with hardware and firmware version
The side labeling includes:
Manufacturer's identification
Connector pin assignment
Serial number
Approval information
Pos : 24.7.2 /All e Serien ( Allgemei ne Module)/Ü bers chriften/N eue Ü berschriften/Ebene 3F ertigungsnummer - Übersc hrift 3 @ 24\mod_1443678821592_21.doc x @ 192641 @ 3 @ 1
3.2.1
Manufacturing Number
Pos : 24.7.3 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Bedruc kung/PFC xxx/F ertigungsnummer 750- 8xxx - Ei nleitung @ 24\mod_1444111093912_21.doc x @ 192818 @ @ 1
The serial number indicates the delivery status directly after production.
Pos : 24.7.4 /Serie 750 (WAGO-I/O-SYST EM)/Gerätebesc hrei bung/Bedruc kungFertigungsnummer 750- xxxx - Abbildung und Erl äuter ung @ 24\mod_1443678328855_21.doc x @ 192638 @ @ 1
Figure 2: Marking Area for Serial Numbers
There are two serial numbers in two rows in the side marking. They are left of the
release tab. The first 10 positions in the longer row of the serial numbers contain
version and date identifications.
Example structure of the rows: 0114010101…
01
WW
Calendar
week
14
YY
Year
01
01
01
FW -HW
FL
Firmware Hardware Firmware
version
version
loader
version
(additional positions)
Internal information
The row order can vary depending on the production year, only the longer row is
relevant. The back part of this and the shorter row contain internal administration
information from the manufacturer.
Pos : 24.8 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
30
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 24.9 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/N eue Ü berschriften/Ebene 2Anschl üss e - Ü berschrift 2 @ 4\mod_1240984262656_21.doc x @ 31961 @ 2 @ 1
3.3
Connectors
Pos : 24.10.1 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Ansc hlüss e/D atenkontakte/Klemmenbus - Ü bersc hrift 3 @ 6\mod_1256294684083_21.doc x @ 43660 @ 3 @ 1
3.3.1
Data Contacts/Internal Bus
Pos : 24.10.2.1 /Serie 750 ( WAGO-I/O- SYST EM)/Wic htig e Erl äuter ung en/Sic her hei ts- und s onstige Hi nweise/Ac htung/Ac htung: Bus kl emmen nicht auf Gol dfeder kontakte l egen! @ 7\mod_1266318463636_21.doc x @ 50695 @ @ 1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pos : 24.10.2.2 /Serie 750 ( WAGO-I/O- SYST EM)/Wic htig e Erl äuter ung en/Sic her hei ts- und s onstige Hi nweise/Ac htung/Ac htung: ESD - Auf gute Er dung der U mgebung ac hten! @ 7\mod_1266318538667_21.doc x @ 50708 @ @ 1
Ensure that the environment is well grounded!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, ensure that the environment
(persons, workplace and packing) is well grounded. Avoid touching conductive
components, e.g. data contacts.
Pos : 24.10.2.3 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebes chr eibung/Ansc hlüss eD atenkontakte - C ontroll er, Abbildung und Besc hrei bung @ 13\mod_1342517711123_21.doc x @ 100486 @ @ 1
Communication between the controller and the I/O modules and system power
supply for the I/O modules is provided via the internal data bus, which consists of
6 data contacts designed as self-cleaning gold spring contacts.
Figure 3: Data Contacts
Pos : 24.10.3 /D okumentati on allgemein/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Device Description
31
Pos : 24.10.4 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Ansc hlüss e/Leistungs kontakte/F eldversorg ung - Ü bers chrift 3 @ 6\mod_1256294692864_21.doc x @ 43664 @ 3 @ 1
3.3.2
Power Jumper Contacts/Field Supply
Pos : 24.10.5.1 /Serie 750 ( WAGO-I/O- SYST EM)/Wic htig e Erl äuter ung en/Sic her hei ts- und s onstige Hi nweise/Vorsicht/Vorsic ht: Verletzungsgefahr durch sc harfkantige Mes ser kontakte! @ 6\mod_1256193279401_21.doc x @ 43414 @ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury.
Pos : 24.10.5.2 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebes chr eibung/Ansc hlüss e/Leistungs kontakte 2 LK (F eder) - Einl eitung - C ontroller @ 22\mod_1426083947328_21.doc x @ 177449 @ @ 1
The controller 750-8202/040-000 is equipped with 2 self-cleaning power contacts
for transferring of the field-side power supply to down-circuit I/O modules. These
contacts are designed as spring contacts.
Pos : 24.10.5.3 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebes chr eibung/Ansc hlüss e/Leistungs kontakte 2 LK (F eder) - Abbildung - Controll er @ 22\mod_1426084085126_21.doc x @ 177453 @ @ 1
Figure 4: Power Jumper Contacts
Pos : 24.10.5.4 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebes chr eibung/Ansc hlüss e/Leistungs kontakte 2 LK (F eder) - Leg ende @ 15\mod_1371724465179_21.doc x @ 123726 @ @ 1
Table 4: Legend for Figure “Power Jumper Contacts”
Contact
1
2
Type
Spring contact
Spring contact
Function
Potential feed-in (Uv) for field supply
Potential feed-in (0 V) for field supply
Pos : 24.10.5.5 /Serie 750 ( WAGO-I/O- SYST EM)/Wic htig e Erl äuter ung en/Sic her hei ts- und s onstige Hi nweise/Ac htung/Ac htung: Maxi maler Str om Leis tungs kontakte 10 A @ 3\mod_1226499143500_21.doc x @ 25029 @ @ 1
Do not exceed maximum current via power jumper contacts!
The maximum current to flow through the power jumper contacts is 10 A.
Greater currents can damage the contacts.
When configuring your system, ensure that this current is not exceeded. If
exceeded, insert an additional supply module.
Pos : 24.10.6 /D okumentati on allgemein/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
32
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 24.10.7 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Ansc hlüss e/C AGE C LAMP-Ansc hlüsse - Übersc hrift 3 @ 6\mod_1256296337770_21.doc x @ 43674 @ 3 @ 1
3.3.3
CAGE CLAMP® Connectors
Pos : 24.10.8 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Ansc hlüss e/PFC xxx/Ansc hl üsse 750-8202/0040- xxxx - CAGE CLAMP- Ans chl üss e, Standard, Abbildung + Legende @ 22\mod_1426083619469_21.doc x @ 177441 @ @ 1
Figure 5: CAGE CLAMP® Connectors
Table 5: Legend for Figure “CAGE CLAMP® Connectors”
Contact
1
2
3
5
6
7
Description
24 V
+
−
0V
+
−
Description
System power supply voltage +24 V
Field-side power supply voltage UV
Field-side power supply voltage 0 V
System power supply voltage 0 V
Field-side power supply voltage UV
Field-side power supply voltage 0 V
Pos : 24.10.9 /Alle Serien (Allgemeine M odul e)/Sic herheits- und s onstige Hinweise/Hinweis/Hi nweis : F ür GL-Ei ns atz ergänz ende Ei ns peis evorschriften beac hten! @ 18\mod_1392115155057_21.doc x @ 144983 @ @ 1
</dg_
Observe supplementary power supply regulations for use in shipbuilding!
Observe supplementary power supply regulations for shipbuilding and the supply
voltage in Section “Connect Devices” > … > “Supplementary Power Supply
Regulations”!
Pos : 24.10.10 /D okumentation allgemein/Gliederungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Device Description
Pos : 24.10.11.1 /Serie 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Bedienelemente/Fel dbus koppl er/-contr oller/Ser vic e-Schnitts tell e - Ü bers chrift 3, und allgemei ne Ei nlei tung @ 4\mod_1239105167430_21.doc x @ 30221 @ 3 @ 1
3.3.4
Service Interface
The service interface is located behind the flap.
Pos : 24.10.11.2 /Serie 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Ans chl üss e/PFC xxx/Ansc hlüss e 750- 8xxx - Ser vice- Sc hnittstelle @ 16\mod_1378986873623_21.doc x @ 131406 @ @ 1
The Service interface is used for communication with WAGO-I/O-CHECK and
WAGO-ETHERNET-Settings and for firmware download.
Figure 6: Service Interface (Closed and Open Flap)
Table 6: Service Interface
Number
1
2
Description
Open flap
Service interface
Pos : 24.10.11.3 /Serie 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Bedienelemente/Fel dbus koppl er/-contr oller/Ac htung: Gerät mus s s pannungsfrei sei n! (für Anschl uss von 750- 920, -923, -921) @ 4\mod_1239105946740_21.doc x @ 30247 @ @ 1
Device must be de-energized!
To prevent damage to the device, unplug and plug in the communication cable
only when the device is de-energized!
The connection to the 4-pin header under the cover flap can be realized via the
communication cables with the item numbers750-920 and 750-923 or via the
WAGO radio adapter with the item number 750-921.
Pos : 24.10.12 /D okumentation allgemein/Gliederungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
33
34
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 24.10.13 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Ans chl üss e/PFC xxx/Ansc hlüss e 750- 8xxx - ETH ERNET, Übersc hrift 3 + Abbildung + Legendentabelle @ 12\mod_1341983627495_21.doc x @ 99595 @ 3 @ 1
3.3.5
Network Connections – X1, X2
Figure 7: Network Connections – X1, X2
Table 7: Legend for Figure “Network Connections – X1, X2”
Contact
1
2
3
4
5
6
7
8
Signal
TD +
TD −
RD +
NC
NC
RD −
NC
NC
Description
Transmit Data +
Transmit Data −
Receive Data +
Not assigned
Not assigned
Receive Data −
Not assigned
Not assigned
Pos : 24.10.14 /D okumentation allgemein/Gliederungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Device Description
35
Pos : 24.10.15 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Ans chl üss e/PFC xxx/Ansc hlüss e 750- 8xxx - RS- 232/R S-485, Ü berschrift 3 + Bel egung + Ansc haltung @ 12\mod_1341983625400_21.doc x @ 99591 @ 344 @ 1
Kommuni kati onsansc hlus s
3.3.6
RS-232/RS-485 – X3 Communication Connection
Figure 8: RS-232/RS-485 – X3 Communication Connection
Table 8: Legend for Figure “RS-232/RS-485 – X3 Communication Connection”
RS-232
Signal
Description
1
NC
Not assigned
2
RxD
Receive Data
3
TxD
Transmit Data
4
NC
Not assigned
5
FB_GND Ground
6
NC
Not assigned
7
RTS
Request to send
8
CTS
Clear to send
9
NC
Not assigned
Enclosure Shield
Shielding
Contact
RS-485
Signal
Description
NC
Not assigned
NC
Not assigned
RxD/TxD-P Receive/transmit data +
NC
Not assigned
FB_GND
Ground
FB_5V
Power Supply
NC
Not assigned
RxD/TxD-N Receive/transmit data −
NC
Not assigned
Shield
Shielding
Incorrect parameterization can damage the communication partners!
The voltage levels are −12 V and +12 V for RS-232, and −5 V and +5 V for
RS-485.
If the controller interfaces differ from those of the communication partners
(RS-232 <> RS-485 or RS-485 <> RS-232), this may damage the interface of the
communication partner.
Therefore, always ensure that the controller interface matches those of its
communication partners when configuring these items!
DC/DC converters and optocouplers in the fieldbus interface electrically isolate
the fieldbus system and the electronics.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
36
Device Description
3.3.6.1
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Operating as an RS-232 Interface
Depending on the device type DTE (e.g., PC) or DCE (e.g., PFC, modem), the
RS-232 signals have different data directions.
Table 9: Function of RS-232 Signals for DTE/DCE
Data Direction
Contact
Signal
2
3
5
7
8
RxD
TxD
FB_GND
RTS
CTS
DTE
Input
Output
--Output
Input
DCE
Output
Input
--Input
Output
For a DTE-to-DCE connection, the signals are connected directly (1:1).
Figure 9: Termination with DTE-DCE Connection (1:1)
For a DTE-to-DTE connection, the signal connections are crossed.
Figure 10: Termination with DTE-DTE Connection (Cross-Over)
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
3.3.6.2
Device Description
37
Operating as an RS-485 Interface
To minimize reflection at the end of the line, the RS-485 line must be terminated
at both ends by a cable termination. If required, one pull-up or pull-down resistor
may be used. These resistors ensure a defined level on the bus when no subscriber
is active, i.e., when all subscribers are in “Tri-state”.
Attention — bus termination!
The RS-485 bus segment must be terminated at both ends!
No more than two terminations per bus segment may be used!
Terminations may not be used in stub and branch lines!
Operation without proper termination of the RS-485 network may result in
transmission errors.
Figure 11: RS-485 Bus Termination
Pos : 24.11 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
38
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 24.12 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 2Anz eigeelemente - Übersc hrift 2 @ 4\mod_1240984390875_21.doc x @ 31964 @ 2 @ 1
3.4
Display Elements
Pos : 24.13.1 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Anzeig eel emente/PFC xxx/Anz eigeel emente 750- 8xxx/0040- xxxx - Vers orgung, Übersc hrift 3 + Abbil dung + Legendentabell e @ 22\mod_1426084900501_21.doc x @ 177468 @ 3 @ 1
3.4.1
Power Supply Indicating Elements
Figure 12: Power Supply Indicating Elements
Table 10: Legend for Figure “Power Supply Indicating Elements”
Description
A
C
Color
Green/off
Green/off
Description
Status of system power supply voltage
Status of field-side power supply voltage
Pos : 24.13.2 /D okumentati on allgemein/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Device Description
39
Pos : 24.13.3 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Anzeig eel emente/PFC xxx/Anz eigeel emente 750- 8xxx - Fel dbus /Sys tem, Ü bersc hrift 3 @ 13\mod_1342507577846_21.doc x @ 100424 @ 3 @ 1
3.4.2
Fieldbus/System Indicating Elements
Pos : 24.13.4 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Anzeig eel emente/PFC xxx/Anz eigeel emente 750- 8202 - F eldbus/Anz eigeelemente 750-8202 - F el dbus/System, Abbildung @ 12\mod_1341838179308_21.doc x @ 99282 @ @ 1
Figure 13: Indicating Elements for Fieldbus/System
Pos : 24.13.5 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Anzeig eel emente/PFC xxx/Anz eigeel emente 750- 8xxx - Fel dbus /Sys tem, Leg endentabell e, Kopfzeil e @ 12\mod_1341574444706_21.doc x @ 99071 @ @ 1
Table 11: Legend for Figure “Fieldbus/System Indicating Elements”
Description
Color
Description
Red/Green/
Orange/Off
System status
Red/Green/
Orange/Off
PLC program status
Red/Green/
Orange/Off
Internal data bus status
Pos : 24.13.6 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Anzeig eel emente/PFC xxx/Anz eigeel emente 750- 8xxx - Fel dbus /Sys tem, Leg endentabell e, Z eile System SYS @ 12\mod_1341834449888_21.doc x @ 99226 @ @ 1
SYS
Pos : 24.13.7 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Anzeig eel emente/PFC xxx/Anz eigeel emente 750- 8xxx - Fel dbus /Sys tem, Leg endentabell e, Z eile System RUN @ 12\mod_1341834703789_21.doc x @ 99240 @ @ 1
RUN
Pos : 24.13.8 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Anzeig eel emente/PFC xxx/Anz eigeel emente 750- 8xxx - Fel dbus /Sys tem, Leg endentabell e, Z eile System I/O @ 12\mod_1341834868679_21.doc x @ 99248 @ @ 1
I/O
Pos : 24.13.9 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Anzeig eel emente/PFC xxx/Anz eigeel emente 750- 8xxx - Fel dbus /Sys tem, Leg endentabell e, Z eile EtherNet/IP M S, n.v. @ 12\mod_1341830669584_21.doc x @ 99210 @ @ 1
CG
Without function
Pos : 24.13.10 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Anz eigeelemente/PFC xxx/Anzeigeel emente 750-8xxx - F eldbus/System, Legendentabelle, Z eile Ether net/IP N S, n.v. @ 12\mod_1341830670256_21.doc x @ 99214 @ @ 1
NS
Without function
Pos : 24.13.11 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Anz eigeelemente/PFC xxx/Anzeigeel emente 750-7xxx/- 8xxx - Fel dbus/Anzeig eel emente 750-8xxx - F el dbus/Sys tem, Legendentabelle, Z eile U 7 @ 13\mod_1355743231449_21.doc x @ 107726 @ @ 1
U7
Red/Green/
Orange/Off
User LED 7, programmable using function
blocks from the WAGO libraries to control the
LEDs
Red/Green/
Orange/Off
User LED 6, programmable using function
blocks from the WAGO libraries to control the
LEDs
Red/Green/
Orange/Off
User LED 5, programmable using function
blocks from the WAGO libraries to control the
LEDs
Red/Green/
Orange/Off
User LED 4, programmable using function
blocks from the WAGO libraries to control the
LEDs
Red/Green/
Orange/Off
User LED 3, programmable using function
blocks from the WAGO libraries to control the
LEDs
Red/Green/
Orange/Off
User LED 2, programmable using function
blocks from the WAGO libraries to control the
LEDs
Red/Green/
Orange/Off
User LED 1, programmable using function
blocks from the WAGO libraries to control the
LEDs
Pos : 24.13.12 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Anz eigeelemente/PFC xxx/Anzeigeel emente 750-7xxx/- 8xxx - Fel dbus/Anzeig eel emente 750-8xxx - F el dbus/Sys tem, Legendentabelle, Z eile U 6 @ 13\mod_1355743227511_21.doc x @ 107722 @ @ 1
U6
Pos : 24.13.13 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Anz eigeelemente/PFC xxx/Anzeigeel emente 750-7xxx/- 8xxx - Fel dbus/Anzeig eel emente 750-8xxx - F el dbus/Sys tem, Legendentabelle, Z eile U 5 @ 13\mod_1355743225308_21.doc x @ 107718 @ @ 1
U5
Pos : 24.13.14 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Anz eigeelemente/PFC xxx/Anzeigeel emente 750-7xxx/- 8xxx - Fel dbus/Anzeig eel emente 750-8xxx - F el dbus/Sys tem, Legendentabelle, Z eile U 4 @ 13\mod_1355743222308_21.doc x @ 107714 @ @ 1
U4
Pos : 24.13.15 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Anz eigeelemente/PFC xxx/Anzeigeel emente 750-7xxx/- 8xxx - Fel dbus/Anzeig eel emente 750-8xxx - F el dbus/Sys tem, Legendentabelle, Z eile U 3 @ 13\mod_1355743214949_21.doc x @ 107710 @ @ 1
U3
Pos : 24.13.16 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Anz eigeelemente/PFC xxx/Anzeigeel emente 750-7xxx/- 8xxx - Fel dbus/Anzeig eel emente 750-8xxx - F el dbus/Sys tem, Legendentabelle, Z eile U 2 @ 12\mod_1341576806109_21.doc x @ 99102 @ @ 1
U2
Pos : 24.13.17 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Anz eigeelemente/PFC xxx/Anzeigeel emente 750-8xxx - F eldbus/System, Legendentabelle, Z eile U 1 @ 12\mod_1341576802500_21.doc x @ 99098 @ @ 1
U1
Pos : 24.13.18 /D okumentation allgemein/Gliederungselemente/------Leerzeile------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1
Pos : 24.13.19 /D okumentation allgemein/Gliederungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
40
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 24.13.20 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Anz eigeelemente/PFC xxx/Anzeigeel emente 750-82xx - Speicher kartenstec kplatz, Ü berschrift 3 + Abb. + Legendentabelle @ 12\mod_1341922811003_21.doc x @ 99562 @ 3 @ 1
3.4.3
Memory Card Indicating Elements
Figure 14: Indicating Elements, Memory Card Slot
Table 12: Legend for Figure “Indicating Elements, Memory Card Slot”
Description
SD
Color
Yellow/Off
Description
Memory card status
Pos : 24.13.21 /D okumentation allgemein/Gliederungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Device Description
Pos : 24.13.22 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Anz eigeelemente/PFC xxx/Anzeigeel emente 750-8xxx - RJ 45, Ü berschrift 3 + Abbildung + Legendentabelle @ 12\mod_1341922805831_21.doc x @ 99558 @ 3 @ 1
3.4.4
Network Indicating Elements
Figure 15: Indicating Elements, RJ-45 Jacks
Table 13: Legend for Figure “Indicating Elements, RJ-45 Jacks”
Description
LNK
ACT
Color
Green/Off
Yellow/Off
Pos : 24.14 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Description
ETHERNET connection status
ETHERNET data exchange
41
42
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 24.15 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 2Bedienel emente - Übersc hrift 2 @ 4\mod_1239191655456_21.doc x @ 30439 @ 2 @ 1
3.5
Operating Elements
Pos : 24.16.1 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 3Betri ebs artenschalter - Ü bersc hrift 3 @ 13\mod_1348214579862_21.doc x @ 103150 @ 3 @ 1
3.5.1
Operating Mode Switch
Pos : 24.16.2 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Bedi enel emente/PFC xxx/Bedi enel emente 750-82xx - Betriebs artens chalter - Abbildung @ 12\mod_1342006664014_21.doc x @ 99662 @ @ 1
Figure 16: Mode Selector Switch
Pos : 24.16.3 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Bedi enel emente/PFC xxx/Bedi enel emente 750-8xxx - Betriebsar tensc hal ter - Ergänzung Laufz eits ystem @ 19\mod_1405062696725_21.doc x @ 158614 @ @ 1
The function of the mode selector switch depends on the activated runtime system
(CODESYS 2 or e!RUNTIME).
Pos : 24.16.4 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 4Laufz eits ystem COD ESYS 2 - Übersc hrift 4 @ 19\mod_1404997478951_21.doc x @ 158374 @ 4 @ 1
3.5.1.1
CODESYS 2 Runtime System
Pos : 24.16.5 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Bedi enel emente/PFC xxx/Bedi enel emente 750-8xxx - Betriebsar tensc hal ter - Erläuterung, C ODESYS 2 @ 19\mod_1405062109675_21.doc x @ 158598 @ @ 1
</dg_
Table 14: Mode Selector Switch
Item
RUN
STOP
RESET
Activation Function
Normal mode
Latching
CODESYS 2 application runs.
Stop
Latching
CODESYS 2 application stopped.
Reset warm start or
Reset cold start
Spring-return
(based on the duration of activation, see Section
“Starting” > “Initiating Reset Functions”)
Pos : 24.16.6 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Bedi enel emente/PFC xxx/Bedi enel emente 750-8xxx - Betriebsar tensc hal ter - Ergänzung R eset-Tas ter @ 19\mod_1405062127693_21.doc x @ 158606 @ @ 1
</dg_
Other functions can also be initiated using the reset button.
Pos : 24.16.7 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 4Laufz eits ystem e!RUNTIM E - Ü bersc hrift 4 @ 19\mod_1404997480277_21.doc x @ 158452 @ 4 @ 1
3.5.1.2
e!RUNTIME Runtime System
Pos : 24.16.8 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Bedi enel emente/PFC xxx/Bedi enel emente 750-8xxx - Betriebsar tensc hal ter - Erläuterung, e!RUNTIME @ 19\mod_1405062121811_21.doc x @ 158602 @ @ 1
</dg_
Table 15: Mode Selector Switch
Position
RUN
STOP
RESET
Actuation
Function
Normal operation
Latching
e!RUNTIME applications running.
Stop
Latching
All e!RUNTIME applications have stopped.
Reset warm start or
Reset cold start
Spring-return
(depending on length of actuation, see Section
“Starting” > “Initiating Reset Functions”)
Pos : 24.16.9 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Bedi enel emente/PFC xxx/Bedi enel emente 750-8xxx - Betriebsar tensc hal ter - Ergänzung R eset-Tas ter @ 19\mod_1405062127693_21.doc x @ 158606 @ @ 1
</dg_
Other functions can also be initiated using the reset button.
Pos : 24.16.10 /D okumentation allgemein/Gliederungselemente/---Sei tenwechsel--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Device Description
43
Pos : 24.16.11 /Alle Seri en (Allgemeine M odule)/Ü berschriften/N eue Übersc hriften/Ebene 3R es et-T aster - Ü bersc hrift 3 @ 17\mod_1382345679844_21.doc x @ 134640 @ 3 @ 1
3.5.2
Reset Button
Pos : 24.16.12 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Bedienelemente/PFC xxx/Bedienelemente 750-8xxx - R eset-Tas ter - Abbil dung + Erläuter ung @ 12\mod_1342006622703_21.doc x @ 99658 @ @ 1
Figure 17: Reset Button
The Reset button is installed behind drilling to prevent operating errors. It is a
shortstroke button with a low actuating force of 1.1 N … 2.1 N (110 gf … 210 gf).
The button can be actuated using a suitable object (e.g., pen).
You can initiate different functions using the Reset button depending on the
position of the mode selector:
-
Temporarily set a fixed IP address
Perform a software reset (restart)
Restore factory setting (factory reset)
Please refer to the same sections in the back of this manual for information about
the functions.
Pos : 24.17 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
44
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 24.18 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 2Speicher kartenstec kpl atz - Ü berschrift 2 @ 9\mod_1296046052394_21.doc x @ 68963 @ 2 @ 1
3.6
Slot for Memory Card
Pos : 24.19.1 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Sons tige Elemente (Speic her kartenstec kplatz, SIM-Kartenstec kpl atz , Batteriefac h etc.)/PFC xxx/Speicher kartenstec kplatz 750- 82xx PFC200 - SD- Speic her kartens tec kpl atz , Abbildung + Erläuterung @ 16\mod_1375436921001_21.doc x @ 127680 @ @ 1
Figure 18: Slot for SD Memory Card
The slot for the SD memory card is located on the front of the housing. The
memory card is locked in the enclosure by a push/push mechanism. Inserting and
removing the memory card is described in the Section “Service” > “Inserting and
Removing the Memory Card.”
The memory card is protected by a cover flap. The cover cap is sealable.
Pos : 24.19.2 /Alle Serien (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits- und s onstige Hinweise/HinweisHinweis: Speicher kar te is t nicht i m Liefer umfang des C ontr ollers enthalten! @ 19\mod_1404994613368_21.doc x @ 158366 @ @ 1
Memory card is not included in the scope of delivery!
Note, the controller is delivered without memory card.
To use a memory card, you must order one separately. The controller can also be
operated without memory card expansion, the use of a memory card is optional.
Pos : 24.19.3 /Alle Serien (Allgemeine M odul e)/Wichtige Erläuter ungen/Sic herheits- und s onstige Hinweise/HinweisHinweis: Nur empfohl ene Speic her karte " SD" für C ontroller ver wenden! @ 19\mod_1404994303733_21.doc x @ 158348 @ @ 1
</dg_
Only use recommended memory cards!
Use only the SD memory card available from WAGO (item No. 758-879/000001) as it is suitable for industrial applications subjected to environmental
extremes and was developed for use in the controller.
Compatibility with other commercially available storage media cannot be
guaranteed.
Pos : 24.20 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 24.21 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 2Schematisc hes Sc haltbild - Ü berschrift 2 @ 4\mod_1240984441312_21.doc x @ 31967 @ 2 @ 1
3.7
Schematic Diagram
Pos : 24.22 /Serie 750 ( WAGO-I/O-SYST EM)/Gerätebeschr eibung/Sc hematis che Sc haltbilder/PFC xxx/Sc hematis ches Sc haltbild 750-8202/0040-0000 XTR @ 22\mod_1426085606310_21.doc x @ 177474 @ @ 1
Figure 19: Schematic Diagram
Pos : 24.23 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Device Description
45
46
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 24.24 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 2T echnisc he Daten - Ü berschrift 2 @ 3\mod_1232967587687_21.doc x @ 26924 @ 2 @ 1
3.8
Technical Data
Pos : 24.25.1 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Tec hnische D aten/VS ( Vari abl ensteuerung)/Tec hnische D aten Ger ät (VS) - XTR @ 15\mod_1369311215011_21.doc x @ 120260 @ 3 @ 1
3.8.1
Device
Table 16: Technical Data – Device
Width
Height (from upper edge of DIN 35 rail)
Length
Weight
Degree of protection
79 mm
65 mm
100 mm
210 g
IP20
Pos : 24.25.2 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Tec hnische D aten/PFC xxx/Tec hnische D aten 750-82xx - Sys temdaten @ 16\mod_1374733902692_21.doc x @ 126956 @ 3 @ 1
</dg_
3.8.2
System Data
Table 17: Technical Data – System Data
CPU
Operating System
Cortex A8, 600 MHz
Real-time Linux® 3.18 (with RT
Preemption Patch)
Push-push mechanism, sealable cover
lid
SD and SDHC up to 32 Gbytes
(All guaranteed properties are valid only
in connection with the WAGO 758879/000-001 memory card.)
Memory card slot
Type of memory card
Pos : 24.25.3 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Tec hnische D aten/VS ( Vari abl ensteuerung)/Tec hnische D aten Vers orgung ( VS) PFC - XTR @ 22\mod_1426603006172_21.doc x @ 177957 @ 3 @ 1
3.8.3
Supply
Table 18: Technical Data – Supply
Internal current consumption (5 VDC)
Total current for I/O modules (5 VDC)
Input current typ. at nominal load
(24 VDC)
Power failure time acc. IEC 61131-2
Power supply
under laboratory conditions
+15 °C … +35 °C
for ambient operating temperature
−40 °C … +55 °C
for ambient operating temperature
+55 °C … +70 °C
Voltage via power jumper contacts:
Efficiency of power supply typ.
at nominal load
Rated surge voltage
1)
510 mA
1700 mA
550 mA
Depending on external buffering
Via CAGE CLAMP® connectors
24 VDC
18 V … 31.2 V (17.4 V … 31.2 V) 1)
18 V … 28.8 V (17.4 V … 28.8 V) 1)
18 V … 26.4 V (17.4 V … 26.4 V) 1)
24 VDC
90 %
1 kV
Including residual ripple of 15 %
Pos : 24.25.4 /Serie 750 ( WAGO-I/O- SYST EM)/Wic htig e Erl äuter ung en/Sic her hei ts- und s onstige Hi nweise/Hinweis/Hi nweis : F ür Systemvers orgung exter ne Pufferung vornehmen! @ 24\mod_1449582212007_21.doc x @ 196902 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Device Description
47
Buffer for system power supply!
The system power supply must be buffered to bridge power outages. As the power
demand depends on the respective node configuration, buffering is not
implemented internally.
To achieve power outages of 1 ms to 10 ms according to IEC61131-2, determine
the buffering appropriate for your node configuration and structure it as an
external circuit.
Pos : 24.25.5 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Tec hnische D aten/PFC xxx/Tec hnische D aten 750-8xxx - U hr @ 18\mod_1389868272711_21.doc x @ 142128 @ 3 @ 1
</dg_
3.8.4
Clock
Table 19: Technical Data – Clock
Drift - system clock (25 °C)
Drift - RTC (25 °C)
Buffer time RTC (25 °C)
20 ppm
3 ppm
30 days
Pos : 24.25.6 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Tec hnische D aten/PFC xxx/Tec hnische D aten 750-82xx - Pr ogrammi erung, C ODESYS 2 und e!RUNTIME @ 20\mod_1406702188097_21.doc x @ 160582 @ 3 @ 1
3.8.5
Programming
Table 20: Technical Data – Programming
Programming
CODESYS 2
e!RUNTIME
IEC 61131-3
CODESYS 2 memory configuration
Program memory (Flash)
Data memory (RAM)
Non-volatile memory (NVRAM,
Retain + Flags)
e!RUNTIME memory configuration
Program and data memory
Non-volatile memory (NVRAM,
Retain + Flags)
Retain variables max.
CODESYS 2
e!RUNTIME
WAGO-I/O-PRO V2.3
e!COCKPIT
IL, LD, FBD, ST, FC
16 MByte
64 MByte
128 kByte
60 MByte (dynamically distributed)
128 kByte
10,000
Not specified
Pos : 24.25.7 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Tec hnische D aten/PFC xxx/Tec hnische D aten 750-82xx - Kl emmenbus , COD ESYS 2 und e!RUNTIME @ 22\mod_1424347720608_21.doc x @ 175062 @ 3 @ 1
3.8.6
Internal data bus
Table 21: Technical Data – Internal Data Bus
Number of I/O modules (per node)
with bus extension
Input and output process CODESYS 2
image (max.)
e!RUNTIME
Pos : 24.25.8 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Tec hnische D aten/PFC xxx/Tec hnische D aten 750-82xx - ETH ERNET, C ODESYS 2 und e!RUNTIME @ 21\mod_1416990027304_21.doc x @ 169044 @ 3 @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
64
250
1,000 words
Not specified
48
Device Description
3.8.7
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
ETHERNET
Table 22: Technical Data – ETHERNET
ETHERNET
Transmission medium
Baud rate
Protocols
MODBUS input and
output process image,
max.
2 x RJ-45 (switched or separated mode)
Twisted Pair S-UTP, 100 Ω, Cat 5,
100 m maximum cable length
10/100 Mbit/s; 10Base-T/100Base-TX
DHCP, DNS, SNTP, FTP, FTPS,
SNMP, HTTP, HTTPS, SSH,
MODBUS (TCP, UDP)
CODESYS 2 1,000 words,
also with MODBUS access to the flag
area (see Section "MODBUS" > … >
"Flag Area")
e!RUNTIME 32,000 words
Pos : 24.25.9 /Serie 750 ( WAGO-I/O- SYST EM)/Pr ozessabbild M appi ng/PFC xxx/Hi nweis : Kei n dir ekter Z ugriff vom F eldbus auf das Pr ozes sabbild der Bus kl emmen! @ 16\mod_1379510128893_21.doc x @ 131836 @ @ 1
No direct access from fieldbus to the process image for I/O modules!
Any data that is required from the I/O module process image must be explicitly
mapped in the CODESYS program to the data in the fieldbus process image and
vice versa! Direct access is not possible!
Pos : 24.25.10 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/T ec hnisc he D aten/PFC xxx/T ec hnisc he D aten 750- 8xxx - Seriell e Schnittstell e @ 16\mod_1374734871093_21.doc x @ 126977 @ 3 @ 1
3.8.8
Serial interface
Table 23: Technical Data – Serial Interface
Interface
Protocols
1 x serial interface per TIA/EIA 232 and
TIA/EIA 485 (switchable), 9-pole D-sub
female connector
MODBUS RTU
Pos : 24.25.11 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/T ec hnisc he D aten/VS (Variablensteuer ung)/T ec hnisc he D aten Ansc hlus stechni k ( VS) @ 16\mod_1373273824961_21.doc x @ 125714 @ 3 @ 1
3.8.9
Connection Type
Table 24: Technical Data – Field Wiring
Wire connection
Cross section
Stripped lengths
CAGE CLAMP®
0.25 mm² … 2.5 mm² / AWG 24 … 14
8 mm … 9 mm / 0.33 in
Table 25: Technical Data – Power Jumper Contacts
Power jumper contacts
Voltage drop at Imax.
spring contact, self-cleaning, hard gold
plated
< 1 V at 64 I/O modules
Table 26: Technical Data – Data Contacts
Data contacts
slide contact, self-cleaning, hard gold
plated
Pos : 24.25.12 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/T ec hnisc he D aten/VS (Variablensteuer ung)/T ec hnisc he D aten Mec hanisc he Beding ung en ( VS) - XTR @ 15\mod_1369387569701_21.doc x @ 120364 @ 3 @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
3.8.10
Device Description
49
Mechanical Conditions
Table 27: Technical Data – Mechanical Conditions
Vibration resistance
1)
Max. 5g 1)
Follow the installation instructions
Pos : 24.25.13 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/T ec hnisc he D aten/VS (Variablensteuer ung)/T ec hnisc he D aten klimatis che U mweltbeding ung en ( VS) - XTR @ 15\mod_1369387559187_21.doc x @ 120360 @ 3 @ 1
3.8.11
Climatic Environmental Conditions
Table 28: Technical Data – Climatic Environmental Conditions
Operating temperature range
Storage temperature range
Relative humidity 1)
Elevation above sea level
without temperature derating
with temperature derating
max.
1)
−40 °C … +70 °C
−40 °C … +85 °C
95 %
0 m … 2000 m
2000 m … 5000 m:
5000 m
0.5 K per 100 m
Short-term condensation per Class 3K7/IEC EN 60721-3-3 and E DIN 40046-721-3 (except
wind-driven precipitation, water and ice formation)
Pos : 24.25.14 /Seri e 750 ( WAGO-I/O-SYSTEM)/Wic htige Erläuterungen/Sicherheits- und s ons tige Hi nweis e/Ac htung/Achtung: Eing esc hränkter T emperatur ber eich bei verti kaler Einbaul age! (XTR PFC) @ 23\mod_1436880749283_21.doc x @ 186221 @ @ 1
Limited temperature range in vertical position!
When mounted vertically, a maximum operating temperature of 65 °C must not
be exceeded! Otherwise, the functionality of the device cannot be ensured and the
device may be damaged.
Pos : 24.26 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
50
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 24.27 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 2Z ulass ungen - Ü bersc hrift 2 @ 3\mod_1224055364109_21.doc x @ 24030 @ 2 @ 1
3.9
Approvals
Pos : 24.28.1 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Zul ass ung en/Infor mati on: Weiter e Informati onen z u Z ulassungen 750- xxxx @ 3\mod_1227190967156_21.doc x @ 25221 @ @ 1
More information about approvals.
Detailed references to the approvals are listed in the document “Overview
Approvals WAGO-I/O-SYSTEM 750”, which you can find via the internet
under: www.wago.com > SERVICES > DOWNLOADS > Additional
documentation and information on automation products > WAGO-I/O-SYSTEM
750 > System Description.
Pos : 24.28.2 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Zul ass ung en/Allgemein/Z ul ass ungen FBkoppl er/-contr oller 750- xxxx Allgemein, ohne Variantenangabe - Ei nleitung @ 5\mod_1245241119092_21.doc x @ 35493 @ @ 1
The following approvals have been granted to 750-8202/040-000 fieldbus
coupler/controller:
Pos : 24.28.3 /Alle Serien (Allgemeine M odul e)/Z ulass ungen/Standar dzul ass ungen/CE (Konfor mitäts kennz eic hnung) @ 3\mod_1224494777421_21.doc x @ 24276 @ @ 1
Conformity Marking
Pos : 24.28.4 /D okumentati on allgemein/Gli ederungsel emente/------Leerzeil e------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1
Pos : 24.28.5 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Zul ass ung en/Allgemein/Z ul. in Vorbereitung FBkoppl er/-contr oller 750- xxxx Allgemein, ohne Variantenangabe - Ei nleitung @ 5\mod_1245241269206_21.doc x @ 35497 @ @ 1
The following approvals are pending for 750-8202/040-000 fieldbus
coupler/controller:
Pos : 24.28.6 /Alle Serien (Allgemeine M odul e)/Z ulass ungen/Standar dzul ass ungen/cU Lus (UL508) @ 3\mod_1224055013140_0.doc x @ 24020 @ @ 1
CULUS
UL508
Pos : 24.28.7 /Alle Serien (Allgemeine M odul e)/Z ulass ungen/Standar dzul ass ungenKC - Korea C ertific ate - PFC @ 20\mod_1406536058950_21.doc x @ 160396 @ @ 1
Korea Certification
MSIP-REM-W43-PFC750
Pos : 24.28.8 /D okumentati on allgemein/Gli ederungsel emente/------Leerzeil e------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1
Pos : 24.28.9 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/Zul ass ung en/Ex/Zul ass ung en FBkoppl er/-contr oller 750- xxxx Ex, ohne Vari antenangabe - Einl eitung @ 9\mod_1285063104018_21.doc x @ 64892 @ @ 1
The following Ex approvals have been granted to 750-8202/040-000 fieldbus
coupler/controller:
Pos : 24.28.10 /Alle Seri en (Allgemeine M odule)/Zul ass ung en/Ex-Z ulas sungen/cU Lus/cU Lus (AN SI/ISA 12.12.01) Clas s I, Di v2 ABCD T 4 @ 3\mod_1224054791812_0.doc x @ 24014 @ @ 1
CULUS
ANSI/ISA 12.12.01
Class I, Div2 ABCD T4
Pos : 24.28.11 /D okumentation allgemein/Gliederungselemente/------Leerzeile------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1
Pos : 24.28.12 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Z ulas sungen/Ex/Z ul. i n Vor ber eitung F Bkoppler/-c ontroll er 750- xxxx Ex ohne Varianten - Ei nleitung @ 16\mod_1373974953848_21.doc x @ 126286 @ @ 1
The following Ex approvals are pending for 750-8202/040-000 fieldbus
coupler/controller:
Pos : 24.28.13.1 /Alle Seri en (Allgemeine M odule)/Z ul ass ungen/Ex-Z ulass ungen/Sonstige/AT EX allgemei n @ 16\mod_1373352135578_0.doc x @ 125803 @ @ 1
ATEX
Pos : 24.28.13.2 /Alle Seri en (Allgemeine M odule)/Z ul ass ungen/Ex-Z ulass ungen/IECEx (TÜV Nor d)/IECEx allgemein @ 16\mod_1373353532946_0.doc x @ 125807 @ @ 1
IECEx
Pos : 24.28.14 /D okumentation allgemein/Gliederungselemente/------Leerzeile------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1
Pos : 24.28.15 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Z ulas sungen/Schi ff/Einl eitungss ätz eZ ul. i n Vor ber eitung F Bkoppler/-c ontroll er 750- xxxx Sc hiff, ohne Variantenangabe - Ei nleitung @ 6\mod_1255592681734_21.doc x @ 42823 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Device Description
The following ship approvals are pending for 750-8202/040-000 fieldbus
coupler/controller:
Pos : 24.28.16 /Alle Seri en (Allgemeine M odule)/Zul ass ung en/Sc hiffs zul ass ung en/GL (Ger manisc her Ll oyd) C at. A, B, C , D ( EMC 1), H @ 15\mod_1370521488638_0.doc x @ 122022 @ @ 1
GL (Germanischer Lloyd)
Cat. A, B, C, D (EMC 1), H
Pos : 24.28.17.1 /Alle Seri en (Allgemeine M odule)/Z ul ass ungen/Sc hiffs zul ass ung en/ABS (Americ an Bureau of Shi pping) @ 3\mod_1224055151062_0.doc x @ 24023 @ @ 1
ABS (American Bureau of Shipping)
Pos : 24.28.17.2 /Alle Seri en (Allgemeine D okumente) (Allgemeine M odule)/Z ul ass ungen/Sc hiffs zul ass ung en/BSH (Bundes amt für Seesc hifffahrt und H ydrographi e) @ 5\mod_1246341825156_21.doc x @ 36334 @ @ 1
Federal Maritime and Hydrographic Agency
Pos : 24.28.17.3 /Alle Seri en (Allgemeine D okumente) (Allgemeine M odule)/Z ul ass ungen/Sc hiffs zul ass ung en/BV (Bureau Veritas) @ 3\mod_1224492116171_0.doc x @ 24220 @ @ 1
BV (Bureau Veritas)
Pos : 24.28.17.4 /Alle Seri en (Allgemeine D okumente) (Allgemeine M odule)/Z ul ass ungen/Sc hiffs zul ass ung en/DNV (D et Nors ke Veritas) Cl ass B @ 3\mod_1224492540562_0.doc x @ 24224 @ @ 1
DNV (Det Norske Veritas)
Class B
Pos : 24.28.17.5 /Alle Seri en (Allgemeine D okumente) (Allgemeine M odule)/Z ul ass ungen/Sc hiffs zul ass ung en/KR ( Kor ean R egister of Shi ppi ng) @ 3\mod_1224492806109_0.doc x @ 24232 @ @ 1
KR (Korean Register of Shipping)
Pos : 24.28.17.6 /Alle Seri en (Allgemeine D okumente) (Allgemeine M odule)/Z ul ass ungen/Sc hiffs zul ass ung en/LR (Lloyd’s Register) Env. 1, 2, 3, 4 @ 3\mod_1224492890453_0.doc x @ 24236 @ @ 1
LR (Lloyd’s Register)
Env. 1, 2, 3, 4
Pos : 24.28.17.7 /Alle Seri en (Allgemeine D okumente) (Allgemeine M odule)/Z ul ass ungen/Sc hiffs zul ass ung en/NKK (Nippon Kaiji Kyokai) @ 3\mod_1224493002656_0.doc x @ 24240 @ @ 1
NKK (Nippon Kaiji Kyokai)
Pos : 24.28.17.8 /Alle Seri en (Allgemeine D okumente) (Allgemeine M odule)/Z ul ass ungen/Sc hiffs zul ass ung en/PR S (Pols ki R ejestr Statków) @ 3\mod_1224497273250_0.doc x @ 24295 @ @ 1
PRS (Polski Rejestr Statków)
Pos : 24.28.17.9 /Alle Seri en (Allgemeine D okumente) (Allgemeine M odule)/Z ul ass ungen/Sc hiffs zul ass ung en/RINA (Registr o Itali ano N avale) @ 3\mod_1224493078359_0.doc x @ 24244 @ @ 1
RINA (Registro Italiano Navale)
Pos : 24.28.17.10 /Dokumentation allgemei n/Gli eder ungs elemente/------Leerz eile------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1
Pos : 24.28.18 /Seri e 750 ( WAGO-I/O-SYSTEM)/Ger ätebesc hrei bung/Z ulas sungen/Schi ff/Infor mation: Weitere Informati on zu den Schiffsz ulas sungen @ 6\mod_1263206668130_21.doc x @ 47820 @ @ 1
For more information about the ship approvals:
Note the “Supplementary Power Supply Regulations” section for the ship
approvals.
Pos : 24.29 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
51
52
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 24.30 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 2N ormen und Ric htlini en - Ü bersc hrift 2 @ 4\mod_1242804031875_21.doc x @ 33646 @ 2 @ 1
3.10
Standards and Guidelines
Pos : 24.31.1 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/N or men und Richtlinien/N or men und Richtlinien F Bkoppl er/-contr oller 750- xxx - Ei nleitung @ 16\mod_1378288254586_21.doc x @ 130746 @ @ 1
750-8202/040-000 fieldbus coupler/controller meets the following standards and
guidelines:
Pos : 24.31.2 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/N or men und Richtlinien/N or men und Richtlinien XTR - M ec hani k und Kli ma Komponenten-HB @ 18\mod_1394633219581_21.doc x @ 147751 @ @ 1
Table 29: Climatic and Mechanical Environmental Conditions
Standard
Transport
EN 60870-2-2
Test Value
Ct2(2k4) (except precipitation / water /
moisture)
Mechanical Environmental Conditions
EN 60870-2-2
Bm
EN 60721-3-1
1M3
EN 60721-3-3
3M5
EN 60068-2-6
Acceleration 5g
IEC 60068-2-27 Shock
15g, 11 ms, 1000 shocks per axis and
direction, half-sine
25g, 6 ms, 1000 shocks per axis and direction,
half-sine
EN 50155
Random vibration:
EN 61373
Category 1, classes A and B
Shock 5g, 30 ms:
Category 1, classes A and B
*)
Shipbuilding
Ambient categories A … D, H
(5g, 25 Hz … 150 Hz)
Climatic Environmental Conditions
EN 60721-3-1
1K5 (except precipitation and ice formation)
EN 60721-3-3
3K7 (except wind-driven precipitation, water
and ice formation)
EN 60870-2-2
C3 (except wind-driven precipitation and ice
formation)
*)
Shipbuilding
Ambient categories A … D, H
(−40 °C … +70 °C)
*)
The list of ship certifications issued is available in the section “Approvals”.
Pos : 24.31.3 /D okumentati on allgemein/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Device Description
Pos : 24.31.4 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/N or men und Richtlinien/EMV-N or men F Bkoppler/-c ontroll er 750- xxxx/0040-0000, ohne Variantenangabe - Ei nleitung XTR @ 18\mod_1395916932582_21.doc x @ 149711 @ @ 1
The fieldbus coupler/controller 750-8202/040-000 meets the following EMC
standards as these standards relate to the fieldbus coupler/controller:
Pos : 24.31.5 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/N or men und Richtlinien/N or men Störfestig kei t XTR @ 18\mod_1394030613258_21.doc x @ 147348 @ @ 1
Table 30: EMC – Immunity to Interference
Standard
Test Value
Electrostatic Discharge
• EN 61000-4-2
8 kV (contact discharge)
• EN 60255-22-2
8 kV (air discharge)
• IEEE C37.90.3
High-frequency Electromagnetic Fields
• EN 61000-4-3 + A1: + A2
20 V/m (80 MHz … 1 GHz)
• EN 60255-22-3
10 V/m (1 GHz … 3 GHz)
• IEEE C37.90.2
Fast Electrical Transient Disturbances / Burst
• EN 61000-4-4
4 kV
• EN 60255-22-4
• IEEE C37.90.1
Surge Voltage / Surge
• EN 61000-4-5
1 kV (conductor/conductor)
• EN 60255-22-5
2 kV (conductor/ground)
Conducted Disturbances, Induced by High-frequency Fields
• EN 61000-4-6
10 V (150 kHz … 80 MHz)
• EN 60255-22-6
Magnetic Fields With Electrical Frequencies
• EN 61000-4-8
300 A/m continuous / 1000 A/m for 1 s
Pulse-shaped Magnetic Fields
• EN 61000-4-9 + A1
300 A/m
Damped Oscillatory Magnetic Fields
• EN 61000-4-10 + A1
100 A/m
Voltage Dips, Short-term Interruptions and Voltage Fluctuations
• EN 61000-4-11
Standard not applicable
Damped Sinusoidal Oscillations
• EN 61000-4-12
1 kV (conductor/conductor)
2 kV (conductor/ground)
Harmonics and Interharmonics
• EN 61000-4-13 + A1
Standard not applicable
Conducted Asymmetric Disturbances
• EN 61000-4-16 + A1 + A2
30 V continuous
300 V for 1 s
Line Frequency Disturbances
• EN 60255-22-7
Standard not applicable
Alternating Components of the Voltage to DC Line Connections
• EN 61000-4-17+A2
15 %
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
53
54
Device Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 30: EMC – Immunity to Interference
Standard
Test Value
Damped Oscillatory Waves
• EN 61000-4-18 + A1
1.25 kV conductor/conductor
• EN 60255-22-1
2.5 kV conductor/ground
• IEEE C37.90.1
Voltage Dips, Short-term Interruptions and Voltage Fluctuations to DC Supply
Inputs
• EN 61000-4-29
see section “Power Supply Unit”
• EN 60255-11
Harmonics
• Shipbuilding*)
Max. 2 W
DC: 3 Veff,
AC: 10 % to 15th harmonic
10 % … 1 % for 15th to 100th harmonic
1 % for 100th to 200th harmonic
*)
The list of ship certifications issued is available in the section “Approvals”.
Pos : 24.31.6 /Serie 750 ( WAGO-I/O- SYST EM)/Gerätebeschr eibung/N or men und Richtlinien/N or men Störauss endung XTR @ 18\mod_1394087664442_21.doc x @ 147358 @ @ 1
Table 31: EMC – Emission of Interference
Standard
Test Value *)
Enclosure Emission of Interference
• EN 61000-6-3 + A1
30 dB(µV/m), QP, 30 MHz … 230 MHz
• EN 55022 Class B
37 dB(µV/m), QP, 230 MHz … 1 GHz
70 dB(µV/m), Peak, 1 GHz … 3 GHz
50 dB(µV/m), AV, 1 GHz … 3 GHz
74 dB(µV/m), Peak, 3 GHz … 6 GHz
54 dB(µV/m), AV, 3 GHz … 6 GHz
• EN 61000-6-4 + A1
40 dB(µV/m), QP, 30 MHz … 230 MHz
• EN 60255-26
47 dB(µV/m), QP, 230 MHz … 1 GHz
• EN 55011 + A1 Class A
76 dB(µV/m), Peak, 1 GHz … 3 GHz
• EN 55022 Class A
56 dB(µV/m), AV, 1 GHz … 3 GHz
80 dB(µV/m), Peak, 3 GHz … 6 GHz
60 dB(µV/m), AV, 3 GHz … 6 GHz
**)
• Shipbuilding (EMC 1)
80 dB(µV/m) …50 dB(µV/m), QP,
150 kHz … 300 kHz
50 dB(µV/m) … 34 dB(µV/m), QP,
0.3 MHz … 30 MHz
54 dB(µV/m), QP, 30 MHz … 2 GHz
24 dB(µV/m), QP, 156 MHz … 165 MHz
**)
• Shipbuilding (EMC 2)
80 dB(µV/m) … 50 dB(µV/m), QP,
150 kHz … 30 MHz
60 dB(µV/m) … 54 dB(µV/m), QP,
30 MHz … 100 MHz
54 dB(µV/m), QP, 100 MHz … 2 GHz
24 dB(µV/m), QP, 156 MHz … 165 MHz
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Device Description
55
Table 31: EMC – Emission of Interference
Standard
Test Value *)
Conducted Emission of Interference – Line Connection AC Voltage
• EN 61000-6-3 + A1
Standard not applicable
• EN 55022 Class B
• EN 61000-6-4 + A1
Standard not applicable
• EN 55011 + A1 Class A
Conducted Emission of Interference – Line Connection
• Shipbuilding**) (EMC 1)
96 dB(µV) … 50 dB(µV), 10 kHz … 150 kHz
60 dB(µV) … 50 dB(µV),
150 kHz … 350 kHz
50 dB(µV), 0.35 MHz … 30 MHz
**)
• Shipbuilding (EMC 2)
120 dB(µV) … 69 dB(µV),
10 kHz … 150 kHz
79 dB(µV), 150 kHz … 500 kHz
73 dB(µV), 0.5 MHz … 30 MHz
Conducted Emission of Interference – Line Connection DC Voltage
• EN 61000-6-3 + A1
79 dB(µV) QP, 0.15 MHz … 0.5 MHz
• EN 60255-26
66 dB(µV) AV, 0.15 MHz … 0.5 MHz
• EN 55022 Class A
73 dB(µV) QP, 0.5 MHz … 30 MHz
60 dB(µV) AV, 0.5 MHz … 30 MHz
*)
**)
QP = Quasi Peak Detector; AV = Average Detector
If necessary, please find different data in the section “Approval” (regarding approval for EMC 1
or EMC 2).
Pos : 25 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
56
Function Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 26 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 1/Funkti onsbesc hrei bung - Ü bersc hrift 1 @ 4\mod_1239025975389_21.doc x @ 30003 @ 1 @ 1
4
Function Description
Pos : 27 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 2/Netz wer k - Übersc hrift 2 @ 21\mod_1422889211685_21.doc x @ 173451 @ 2 @ 1
</dg_
4.1
Network
Pos : 28.1 /Serie 750 (WAGO-I/O-SYST EM)/F unktions beschr eibung/Netz wer k/PFC xxx/PFC xxx - Sc hnitts tell enkonfiguration @ 19\mod_1404290346550_21.doc x @ 157280 @ 344 @ 1
4.1.1
Interface Configuration
The ETHERNET X1 and X2 interfaces of the controller are connected with an
internal 3-port switch, in which the third port is connected to the CPU.
Interfaces X1 and X2 can either be operated in Switch mode or as separate
network interfaces. The switching can be performed during the runtime.
The Switch mode is activated by default and during initial startup. The
“Configuration mode” is set to “DHCP.”
For interface X1, a fixed IP address can be set (“Fix IP Address”). The setting is
carried out with the Reset button (see Section “Startup” > …> “Setting a Fixed IP
Address”).
Setting a fixed IP address has no effect on the mode previously set.
4.1.1.1
Operation in Switch Mode
For operation in Switch mode, the TCP/IP settings such as the IP address or
subnet mask apply to both X1 and X2.
When switching to Switch mode, the X1 settings are applied as a new common
configuration for X1 and X2.
The device is then no longer accessible via the IP address previously set for X2.
This must be taken into account for CODESYS applications that use X2 for
communication.
4.1.1.2
Operation with Separate Network Interfaces
When operating with separate network interfaces, both ETHERNET interfaces
can be configured and used separately.
Note that the two interfaces still have the same MAC address. Therefore, they
must not be operated in the same network segment.
When switching to operating with separate interfaces, interface X2 is initialized
with the setting values last valid for it. The connections on the X1 interface
persist.
When operating with separate interfaces and fixed IP address, the device can still
be accessed via the interface X2 via the regular IP address.
Pos : 28.2 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Function Description
57
Pos : 28.3 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/N eue Ü berschriften/Ebene 3N etz wer ksic her hei t - Ü bersc hrift 3 @ 21\mod_1422889103009_21.doc x @ 173448 @ 3 @ 1
4.1.2
Network Security
Pos : 28.4 /Serie 750 (WAGO-I/O-SYST EM)/F unktions beschr eibung/Netz wer k/PFC xxx/PFC xxx - Netz wer ksicherheit - Benutz er und Pass wör ter @ 16\mod_1376025742919_21.doc x @ 128310 @ 45555 @ 1
4.1.2.1
Users and Passwords
Several groups of users are provided in the controller which can be used for
various services.
Default passwords are set for all users. We strongly recommend changing these
passwords on startup!
Change passwords
Default passwords are documented in these instructions and therefore do not offer
adequate protection! Change the passwords to meet your particular needs.
4.1.2.1.1 Services and Users
All password-protected services and their associated users are listed in the
following table.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
user
X
admin
X
root
Web Based Management
(WBM)
Linux® console
Console Based Management
(CBM)
CODESYS
Telnet
FTP
FTPS
SSH
SNMP
user
Service
admin
WBM
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
SNMP
Users
Linux®
X
58
Function Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
4.1.2.1.2 WBM User Group
WBM has its own user administration system. The users in this system are
isolated from the other user groups in the system for security reasons.
Detailed information about this is given in the Section “WBM User
Administration”.
Table 32: WBM Users
Users
admin
user
guest
Permissions
All (administrator)
Supported to a limited extent
Display only
Default Password
wago
user
---
Change passwords
Default passwords are documented in these instructions and therefore do not offer
adequate protection! Change the passwords to meet your particular needs.
4.1.2.1.3 Linux® User Group
The Linux® users group include the actual users of the operating system, which is
likewise used by most services.
The passwords for these users must be configured through a terminal connection
via SSH/RS-232.
Table 33: Linux® Users
User
root
admin
user
Special Feature
Super user
CODESYS user
Normal user
Home Directory
/root
/home/admin
/home/user
Default Password
wago
wago
user
Change passwords
Default passwords are documented in these instructions and therefore do not offer
adequate protection! Change the passwords to meet your particular needs.
4.1.2.1.4 SNMP User Group
The SNMP service manages its own users. In its initial state, no users are stored in
the system.
Pos : 28.5 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Function Description
59
Pos : 28.6 /Serie 750 (WAGO-I/O-SYST EM)/F unktions beschr eibung/Netz wer k/PFC xxx/PFC xxx - Netz wer ksicherheit - Webpr otokoll e @ 21\mod_1417677916151_21.doc x @ 169948 @ 4 @ 1
4.1.2.2
Web Protocols for WBM Access
The HTTP and HTTPS web protocols can be used to access the WBM pages for
the controller. HTTPS is preferred because it uses the SSL/TLS protocol. The
SSL/TLS protocol ensures secure communication through encryption and
authentication
The default setting for the controller allows strong encryption, but uses only
simple authentication methods. As authentication for any secure communication
channel plays a central role, it is strongly recommended that you use secure
authentication. The security certificate saved on the controller is the basis for
authentication. The default location for the security certificate is:
/etc/lighttpd/https-cert.pem
As delivered, the controller uses a generic security certificate based on x509. To
allow secure authentication, you must replace the generic security certificate with
a security certificate specific for the individual device.
Pos : 28.7 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
60
Function Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 28.8 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/N eue Ü berschriften/Ebene 3N etz wer kkonfiguration - Ü bers chrift 3 @ 21\mod_1423559074625_21.doc x @ 174006 @ 3 @ 1
</dg_
4.1.3
Network Configuration
Pos : 28.9 /Serie 750 (WAGO-I/O-SYST EM)/F unktions beschr eibung/Netz wer k/PFC xxx/PFC xxx - Netz wer kkonfigur ation - H os tname/Domainname, >= F W04 @ 21\mod_1423557624886_21.doc x @ 173998 @ 4 @ 1
4.1.3.1
Host Name/Domain Name
Without a host name configuration, the controller is assigned a default name
which includes the last three values of the controller's MAC address, e.g.,
“PFCx00-A1A2A3.” This name is valid for as long as a host name was not
configured, or host name was not supplied to the controller via DHCP (for
configuration of the controller see Section “Startup” > “Configuring”). When the
host name is set, a host name supplied by a DHCP response is immediately active
and displaces the configured or default host name. If there are multiple network
interfaces with DHCP, the last received host name is valid. If only the configured
name is to be valid, the network administrator must adjust the configuration of the
active DHCP server so that no host names are transferred in the DHCP response.
The default host name or the configured name is active again if the network
interfaces are set to static IP addresses or if a host name is not received via the
DHCP response.
A similar mechanism is used for a domain name as for the host name. The
difference is that a default domain name is not set. As long as a domain name is
not configured or supplied by DHCP, the domain name is empty.
Pos : 28.10 /Serie 750 ( WAGO-I/O-SYST EM)/Funkti onsbesc hrei bung/N etz wer k/PFC xxx/PFC xxx - N etz wer kkonfiguration - D efaul t-Gateways , >= F W04 @ 21\mod_1423557629195_21.doc x @ 174002 @ 4 @ 1
4.1.3.2
Default Gateways
In the TCP/IP configuration, the controller allows the setting of two default
gateways. A network station transmits to a default gateway all network data
packets for systems outside of its local network. This gateway is responsible for
the appropriate routing of the data packets, so that they reach the target system.
The default gateways are assigned a so-called metric which specifies the time
delay, sometimes called the cost factor, with which a data packet can be routed via
the gateway. If multiple default gateways are configured, the operating system
transmits the data packets to the default gateway configured with the lowest
metric. If this gateway is not accessible, an attempt is made to access the gateway
with the next higher metric. The gateway is determined randomly if multiple
gateways have the same metric. If this gateway cannot transmit the data packet,
the data packet is sent simultaneously to all other gateways of the same metric.
The metric of the configured default gateways can be set for the controller. The
default value for the metric is 20. Besides the directly configured gateways, other
gateways can be set via DHCP responses so that more than two gateways are
possible. All gateways transferred via DHCP are assigned a permanent metric of
10. The DHCP gateways are thus normally given priority on account of their low
metric.
Pos : 28.11 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Function Description
61
Pos : 28.12 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 3N etz wer kdi enste - Ü bersc hrift 3 @ 21\mod_1423559527614_21.doc x @ 174013 @ 3 @ 1
4.1.4
Network Services
Pos : 28.13 /Serie 750 ( WAGO-I/O-SYST EM)/Funkti onsbesc hrei bung/N etz wer k/PFC xxx/PFC xxx - N etz wer kdienste - DHC P-Client, >= F W06 @ 23\mod_1437455048477_21.doc x @ 186548 @ 4 @ 1
4.1.4.1
DHCP Client
The controller can get network parameters from an external DHCP master via the
DHCP Client service.
The following parameters can be obtained:
-
IP address
-
SubNet mask
-
Router/gateway
-
Hostname
-
Domain
-
DNS server
-
NTP server
For the IP address, SubNet mask and router/gateway parameters, the entries are
stored per ETHERNET port (X1, X2).
The Hostname and Domain parameters are stored according to the LIFO principle
(Last In First Out). The settings from the last DHCP offer received are always
used.
The DNS and NTP Server parameters are stored centrally for global use. All
transmitted parameters are saved.
Pos : 28.14 /Serie 750 ( WAGO-I/O-SYST EM)/Funkti onsbesc hrei bung/N etz wer k/PFC xxx/PFC xxx - N etz wer kdienste - DHC P-Ser ver , >= F W04 @ 21\mod_1423559335812_21.doc x @ 174009 @ 4 @ 1
4.1.4.2
DHCP Server
The controller provides the DHCP server service for the automatic configuration
of IP addresses of network stations on the same subnet.
Generally, only one DHCP server can be active on a subnet at one time.
The following can be set for the DHCP server:
-
The service itself (active/not active)
-
The range of dynamically assigned IP addresses
-
The lease time of the dynamically assigned IP addresses
-
A list with static assignments of IP addresses to MAC addresses
In “switched” mode, these settings are possible for both interfaces together and in
“separated” mode for each interface separately.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
62
Function Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
The settings are made, for example, in the WBM via the “DHCP Configuration”
page.
The DHCP server also passes other parameters in addition to the IP address. The
following table shows the complete list.
Table 34: List of Parameters Transmitted via DHCP
Parameters
IP address
Subnet mask
Broadcast address
Lease time
Host name
Name server
Default gateway
Explanation
An IP address from the range of permitted address; the
range can be configured in the WBM.
The DHCP server determines the IP address to be passed to
the requesting network subscriber (client) from the MAC
address of the network subscriber and the range of addresses
to be assigned. As long as the configured address range does
not change and no bottlenecks occur when assigning IP
addresses, the DHCP server continuously reassigns the same
IP addresses to requesting network subscribers.
When a subscriber connects to the network, for whose MAC
address a fixed IP address has been configured in the WBM,
this address is passed to it. Such a fixed IP address can also
be outside the range of freely-assignable IP addresses.
A hostname can also be specified instead of the MAC
address for identifying the requesting network subscriber.
The subnet mask configured in the network settings of the
DHCP server for the local network concerned is passed.
The subnet mask and IP address determine the range of
valid IP addresses on the local network.
IP address with which an IP packet can be sent to all
network subscribers on the subnet at the same time
Determines the validity period of the DHCP parameters
passed to a network subscriber:
Per protocol, the network subscriber is required to request
the network settings again after half the period of validity.
The lease time is configured in the WBM.
The network name is passed to the network subscriber.
The network subscriber normally sends its own name with
its request for the IP address. It is then used by the DHCP
server in its response.
The DHCP server passes its own IP address as the DNS
name server to the network subscriber.
The DHCP server passes its own IP address as the default
gateway to the network subscriber.
The default gateway is required to communication with
subscribers outside the local network.
Not all parameters can be set in the WBM. If you want to set other values for the
existing parameters or want to pass other parameters via DHCP, the DHCP server
must be manually configured. For the controller, the DHCP server service is
handled by the program "dnsmasq".
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Function Description
63
From a Linux® command line, an editor must be used to change the file
“/etc/dnsmasq.d/dnsmasq_default.conf” to set the configuration.
Pos : 28.15 /Serie 750 ( WAGO-I/O-SYST EM)/Funkti onsbesc hrei bung/N etz wer k/PFC xxx/PFC xxx - N etz wer kdienste - DN S-Ser ver, >= F W06 @ 24\mod_1443596187519_21.doc x @ 192580 @ 4 @ 1
4.1.4.3
DNS Server
The controller offers the DNS server service for the automatic assignment of
hostnames to IP addresses of network stations.
The DNS server takes over the names and IP addresses of local network stations
from the DHCP server. This DNS server routes requests for non-local names, such
as from the Internet, to higher-level DNS servers if configured and accessible.
The following settings are possible for the DNS server:
-
The service itself (enabled/disabled)
-
Access type to the assignments
The requests are buffered in “Proxy” mode (throughput optimized).
In Relay mode the requests are routed directly to higher-level name servers.
-
A list with up to 15 static assignments of IP addresses to hostnames
If only the hostname is used, the configured or default domain is added to
the hostname automatically to ensure FQDN name resolution.
The settings are made, e.g., in the WBM, via the “Configuration of DNS Service”
page.
Pos : 29 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
64
Function Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 30 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 2/Speic her kartenfunktion - Ü bers chrift 2 @ 21\mod_1414148937738_21.doc x @ 166430 @ 2 @ 1
4.2
Memory Card Function
Pos : 31.1 /All e Seri en ( Allgemei ne Module)/Wic htige Erläuterungen/Sicherheits- und sons tige Hi nweis e/Hi nweisHi nweis: N ur empfohlene Speicher kar te "SD" für C ontroll er verwenden! @ 19\mod_1404994303733_21.doc x @ 158348 @ @ 1
</dg_
Only use recommended memory cards!
Use only the SD memory card available from WAGO (item No. 758-879/000001) as it is suitable for industrial applications subjected to environmental
extremes and was developed for use in the controller.
Compatibility with other commercially available storage media cannot be
guaranteed.
Pos : 31.2 /Serie 750 (WAGO-I/O-SYST EM)/F unktions beschr eibung/Speic herfunkti on/PFC xxx/Speic herkartenfunktion 750-8xxx PFC xxx - Ei nleitung @ 22\mod_1429683400056_21.doc x @ 180889 @ @ 1
The memory card is optional and serves as an additional memory area in addition
to the internal memory or drive in the controller. The user program, user data, the
source code of the project, or device settings can be saved to the memory card and
thus already existing project data and programs can be copied to one or multiple
controllers.
Deactivate write protection!
In order to be able to write data to the memory card, you must deactivate the
small push switch for the write protection setting. This switch is on one of the
long sides of the memory card.
If the memory card is inserted, this is incorporated under /media/sd in the
directory structure of the file system inside the controller. This means that the
memory card can be addressed like a removable medium on a PC.
Note the pre-formatting of the memory card!
Please note that memory cards ≤ 2 GB are often formatted with the “FAT16” file
system type and can generate up to 512 entries in the root directory. For over 512
entries create these in a subdirectory or format the memory card with “FAT32” or
“NTFS.”
The function of the memory card in normal operation and possible faults that may
occur when the memory card is used are described in the following sections for
different operating modes.
Pos : 31.3 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Function Description
65
Pos : 31.4 /Serie 750 (WAGO-I/O-SYST EM)/F unktions beschr eibung/Speic herfunkti on/PFC xxx/Speic herkartenfunktion 750-8xxx PFC xxx - Bac kup-F unkti on @ 22\mod_1429683405495_21.doc x @ 180897 @ 3 @ 1
4.2.1
Backup Function (Saving of Device Settings to the Memory
Card)
This function enables the data of the internal memory and device settings to be
saved on the memory card during operation.
Requirement: The fieldbus nodes and the PLC program are in operation and the
memory card is plugged in.
The following selection is possible on the “Firmware Backup” page in the WebBased Management:
•
•
•
•
PLC runtime project (boot project)
Settings
System
All (all of the above, only visible if not saved in the network)
The network or the inserted memory card can be selected as the target medium.
The files of the internal drive are stored on the target medium in the directory
media/sd/copy and in the corresponding subdirectories.
The information that is not present as files on the controller is stored in XML
format in the directory media/sd/settings/.
If the memory card is selected as the target medium, the LED above the memory
card slot flashes yellow/orange during the save operation.
The device settings and files of the internal drive are then saved on the target
medium.
Pos : 31.5 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
66
Function Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 31.6 /Serie 750 (WAGO-I/O-SYST EM)/F unktions beschr eibung/Speic herfunkti on/PFC xxx/Speic herkartenfunktion 750-8xxx PFC xxx - Res tor e-Funkti on @ 22\mod_1429683408092_21.doc x @ 180901 @ 3 @ 1
4.2.2
Restore Function (Loading of Device Settings from the
Memory Card)
This function enables the data of the internal memory and device settings to be
saved from the memory card to the internal memory during operation.
Requirement: The fieldbus nodes and the PLC program are in operation and the
memory card is plugged in.
The following selection is possible on the “Firmware Restore” page in the WebBased Management:
•
•
•
•
All (all of the above, only visible if not saved in the network)
PLC runtime project (boot project)
Settings
System
The network or the inserted memory card can be selected as the source medium.
When loading the data, the files are copied from the directory media/sd/copy/ of
the source medium to the appropriate directories on the internal memory.
If the memory card is selected as the source medium, the LED above the memory
card slot flashes yellow/orange during the load operation.
In case of parameter changes, the device executes a restart!
Note that the device taking the data executes a restart if parameters in the internal
drive are overwritten with other parameter settings from the memory card.
The boot project is loaded automatically and the settings automatically activated
after a restart. The “Boot project location” set on the “General PLC Runtime
Configuration Web” page of the WBM determines whether the boot project of the
internal drive or the memory card is loaded.
File size must not exceed the size of the internal drive!
Note that the amount of data in the media/sd/copy/ directory must not exceed the
total size of the internal drive.
Pos : 31.7 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Function Description
67
Pos : 31.8 /Serie 750 (WAGO-I/O-SYST EM)/F unktions beschr eibung/Speic herfunkti on/PFC xxx/Speic herkartenfunktion 750-8xxx PFC xxx - Ei nfügen einer Speicher kar te i m Betrieb @ 22\mod_1429683410574_21.doc x @ 180905 @ 3 @ 1
4.2.3
Inserting a Memory Card during Operation
The fieldbus nodes and the PLC program are running.
Insert a memory card during ongoing operation.
During normal operation, the memory card is incorporated into the file system of
the controller as a drive.
No automatic copy procedures are triggered.
The LED above the memory card flashes yellow/orange during the access.
The memory card is then ready for operation and available under /media/sd.
Pos : 31.9 /Serie 750 (WAGO-I/O-SYST EM)/F unktions beschr eibung/Speic herfunkti on/PFC xxx/Speic herkartenfunktion 750-8xxx PFC xxx - Entfer nen einer Speicher karte im Betri eb @ 22\mod_1429683413499_21.doc x @ 180909 @ 3 @ 1
4.2.4
Removing the Memory Card during Operation
The fieldbus node and the PLC program are in operation and the memory card is
plugged in.
Remove the memory card during ongoing operation.
Data can be lost during writing!
Note that if you pull the memory card out during a write procedure, data will be
lost.
The LED above the memory card flashes yellow/orange during the attempted
access.
The controller then works without a memory card.
Pos : 31.10 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
68
Function Description
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 31.11 /Serie 750 ( WAGO-I/O-SYST EM)/Funkti onsbesc hrei bung/Speic herfunkti on/PFC xxx/Speic her kartenfunkti on 750- 8xxx PFC xxx - Einstell ung des H ome- Verz eic hniss es, >= F W06 @ 23\mod_1441184287444_21.doc x @ 190656 @ 3 @ 1
4.2.5
Setting the Home Directory for the Runtime System
The home directory for the runtime system is located in the controller's internal
memory by default. An existing boot project may be saved in the home directory.
You can use the WBM to move the home directory for the runtime system to the
memory card, e.g., to make more memory available for a large boot project or
other files.
Some conditions must be met before moving the directory.
•
A running IEC-61131 application must be stopped and the device restored
to its initial state using the “Reset” function. Any boot project is deleted.
•
When moving the home directory to the memory card, insert a memory card
formatted to support file system. Only the first partition of a memory card
can be accessed at /media/sd and can be used as the home directory.
Only when the two conditions are met can the “Home directory on memory card
enabled” checkbox be selected from the WBM on the “PLC Runtime” page.
Press the [Submit] button to apply the settings, which take effect after the next
restart.
No files are applied from the old to the new home directory.
After moving the directory, a project must be loaded and a boot project created.
It should be noted that the memory card may not be removed under any
circumstances as long as the home directory is there. If an application is running,
system safety can be endangered by an uncontrolled controller crash.
Switching the home directory has no effect if the controller was botted from a
memory card. The configuration state is saved, but only takes effect if the content
of the memory card is copied to the internal memory.
Pos : 32 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Mounting
69
Pos : 33 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 1/M onti eren - Ü bersc hrift 1 @ 3\mod_1225446744750_21.doc x @ 24900 @ 1 @ 1
5
Mounting
Pos : 34.1 /Serie 750 (WAGO-I/O-SYST EM)/M ontieren/D emontieren/Einbaul age XTR @ 16\mod_1373976754254_21.doc x @ 126292 @ 2 @ 1
5.1
Mounting Position
The following mounting positions are approved:
•
•
•
Lying horizontal
Standing horizontal
Vertical
Use an end stop in the case of vertical installation!
When installed vertically, also mount an end stop below the fieldbus node to
protect the fieldbus node against sliding.
WAGO item number 249-116
end stop for TS 35, 6 mm wide
WAGO item number 249-117
end stop for TS 35, 10 mm wide
Pos : 34.2 /Serie 750 (WAGO-I/O-SYST EM)/M ontieren/D emontieren/Gesamtaus bau XTR @ 16\mod_1373976975062_21.doc x @ 126295 @ 2 @ 1
5.2
Overall Configuration
The maximum total length of a fieldbus node without fieldbus coupler/controller
is 780 mm including end module. The width of the end module is 12 mm. When
assembled, the I/O modules have a maximum length of 768 mm.
Examples:
•
64 I/O modules with a 12 mm width can be connected to a fieldbus
coupler/controller.
•
32 I/O modules with a 24 mm width can be connected to a fieldbus
coupler/controller.
Exception:
The number of connected I/O modules also depends on the type of fieldbus
coupler/controller is used. For example, the maximum number of stackable I/O
modules on one PROFIBUS DP/V1 fieldbus coupler/controller is 63 with no
passive I/O modules and end module.
Observe maximum total length of a fieldbus node!
The maximum total length of a fieldbus node without fieldbus coupler/controller
may not exceed 780 mm.
Also note the limitations of individual fieldbus couplers/controllers.
Pos : 34.3 /Serie 750 (WAGO-I/O-SYST EM)/M ontieren/D emontieren/M ontage auf Tr agschi ene ( XTR) @ 24\mod_1444997402760_21.doc x @ 193805 @ 233 @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
70
Mounting
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
5.3
Mounting onto Carrier Rail
5.3.1
Carrier Rail Properties
All system components can be snapped directly onto a carrier rail in accordance
with the European standard EN 50022 (DIN 35).
Do not use any third-party carrier rails without approval by WAGO!
WAGO Kontakttechnik GmbH & Co. KG supplies standardized carrier rails that
are optimal for use with the I/O system. If other carrier rails are used, then a
technical inspection and approval of the rail by WAGO Kontakttechnik GmbH &
Co. KG should take place.
Carrier rails have different mechanical and electrical properties. For the optimal
system setup on a carrier rail, certain guidelines must be observed:
•
The material must be non-corrosive.
•
Most components have a contact to the carrier rail to ground electromagnetic disturbances. In order to avoid corrosion, this tin-plated carrier rail
contact must not form a galvanic cell with the material of the carrier rail
which generates a differential voltage above 0.5 V (saline solution of 0.3 %
at 20°C).
•
The carrier rail must optimally support the EMC measures integrated into
the system and the shielding of the I/O module connections.
•
A sufficiently stable carrier rail should be selected and, if necessary, several
mounting points (every 20 cm) should be used in order to prevent bending
and twisting (torsion).
•
The geometry of the carrier rail must not be altered in order to secure the
safe hold of the components. In particular, when shortening or mounting the
carrier rail, it must not be crushed or bent.
•
The base of the I/O components extends into the profile of the carrier rail.
For carrier rails with a height of 7.5 mm, mounting points are to be riveted
under the node in the carrier rail (slotted head captive screws or blind
rivets).
•
The medal springs on the bottom of the housing must have low-impedance
contact with the DIN rail (wide contact surface is possible).
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
5.3.2
Mounting
71
WAGO DIN Rail
WAGO carrier rails meet the electrical and mechanical requirements shown in the
table below.
Table 35: WAGO DIN Rail
Order number
210-112 /-113
210-197 /-114
210-118
210-198
210-196
Description
35 × 7.5;
1 mm;
35 × 15; 1.5 mm;
35 × 15; 2.3 mm;
35 × 15; 2.3 mm;
35 × 8.2; 1.6 mm;
steel yellow chromated; slotted/unslotted
steel yellow chromated; slotted/unslotted
steel yellow chromated; unslotted
copper; unslotted
aluminum; unslotted
Pos : 34.4 /Serie 750 (WAGO-I/O-SYST EM)/M ontieren/D emontieren/Bus klemmen 750xxxx/0040xxxx 4g-5g @ 15\mod_1367558844291_21.doc x @ 118470 @ @ 1
For vibration loads > 4g, observe the following installation instructions:
•
Use pan-head screws or blind rivets at least every 60 mm (12 mm pin
spacing) to secure the DIN rail.
•
Make the open conductor length between strain relief and wire connection
as short as possible.
•
Use the reinforced end stop 249-197.
•
When using the PFC200 CS 2ETH RS/XTR (750-8202/040-00x), carrier
rails without an oblong hole must also be used. Alternatively, a material
thickness of min. 1.5 mm must be maintained.
•
When using the PFC200 CS 2ETH RS CAN DPS/XTR
(750-8206/040-00x), carrier rails without an oblong hole with a material
thickness of min. 2.3 mm must also be used.
Pos : 34.5 /Serie 750 (WAGO-I/O-SYST EM)/M ontieren/D emontieren/Aus wahl der Tragsc hiene für XTR- PFC @ 23\mod_1435150387049_21.doc x @ 184498 @ @ 1
Table 36: Permissible WAGO Carrier Rails When Using XTR PFC200
Item Number
210-113
210-114
210-197
210-118
750-8202/040-00x
×
×
×
×
Pos : 34.6 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
750-8206/040-00x
–
–
–
×
72
Mounting
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 34.7 /Serie 750 (WAGO-I/O-SYST EM)/M ontieren/D emontieren/Abstände @ 3\mod_1225448283750_21.doc x @ 24920 @ 2 @ 1
5.4
Spacing
The spacing between adjacent components, cable conduits, casing and frame sides
must be maintained for the complete fieldbus node.
Figure 20: Spacing
The spacing creates room for heat transfer, installation or wiring. The spacing to
cable conduits also prevents conducted electromagnetic interferences from
influencing the operation.
Pos : 34.8 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Mounting
73
Pos : 34.9 /Serie 750 (WAGO-I/O-SYST EM)/M ontieren/D emontieren/M ontagerei henfolge @ 3\mod_1231770210031_21.doc x @ 25992 @ 2 @ 1
5.5
Mounting Sequence
Fieldbus couplers/controllers and I/O modules of the WAGO-I/O-SYSTEM
750/753 are snapped directly on a carrier rail in accordance with the European
standard EN 50022 (DIN 35).
The reliable positioning and connection is made using a tongue and groove
system. Due to the automatic locking, the individual devices are securely seated
on the rail after installation.
Starting with the fieldbus coupler/controller, the I/O modules are mounted
adjacent to each other according to the project design. Errors in the design of the
node in terms of the potential groups (connection via the power contacts) are
recognized, as the I/O modules with power contacts (blade contacts) cannot be
linked to I/O modules with fewer power contacts.
Pos : 34.10 /Serie 750 ( WAGO-I/O-SYST EM)/Wichtig e Erl äuter ung en/Sic her hei ts- und s onstige Hinweise/Vorsicht/Vorsic ht: Verletzungsgefahr durc h sc har fkantige Messer kontakte! @ 6\mod_1256193279401_21.doc x @ 43414 @ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury.
Pos : 34.11 /Serie 750 ( WAGO-I/O-SYST EM)/Wichtig e Erl äuter ung en/Sic her hei ts- und s onstige Hinweise/Ac htung/Ac htung: Bus kl emmen nur in vorges ehener Rei henfolge stec ken! @ 6\mod_1256194177073_21.doc x @ 43429 @ @ 1
Insert I/O modules only from the proper direction!
All I/O modules feature grooves for power jumper contacts on the right side. For
some I/O modules, the grooves are closed on the top. Therefore, I/O modules
featuring a power jumper contact on the left side cannot be snapped from the top.
This mechanical coding helps to avoid configuration errors, which may destroy
the I/O modules. Therefore, insert I/O modules only from the right and from the
top.
Pos : 34.12 /Serie 750 ( WAGO-I/O-SYST EM)/Wichtig e Erl äuter ung en/Sic her hei ts- und s onstige Hinweise/Hinweis/Hi nweis : Bus absc hluss XTR nic ht vergessen! @ 15\mod_1368426836647_21.doc x @ 119458 @ @ 1
Don't forget the bus end module!
Always plug a bus end module 750-600/040-000 onto the end of the fieldbus
node! You must always use this bus end module at all fieldbus nodes with the
WAGO I/O System 750 XTR fieldbus couplers/controllers to guarantee proper
data transfer.
Pos : 34.13 /Serie 750 ( WAGO-I/O-SYST EM)/Wichtig e Erl äuter ung en/Sic her hei ts- und s onstige Hinweise/Hinweis/Hi nweis : XTR - Erhöhte Störfestig keit @ 15\mod_1367496424993_21.doc x @ 118330 @ @ 1
Increased interference!
For standard-compliant application in substation instrumentation and control,
telecontrol systems, railway technology or shipbuilding certified operation,
field-side power supply filter 750-624/040-001 or power supply filter
750-626/040-000 are generally to be used for XTR module groups.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
74
Mounting
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 34.14 /Serie 750 ( WAGO-I/O-SYST EM)/Wichtig e Erl äuter ung en/Sic her hei ts- und s onstige Hinweise/Hinweis/Hi nweis : XTR - Misc hbetri eb XTR /Standard @ 15\mod_1367496420828_21.doc x @ 118326 @ @ 1
Mixed operation
Mixed operation (standard/XTR modules) within a node is possible when groups
of modules are electrically isolated on the field side (i.e., electrically isolated
power supply).
Pos : 34.15 /Serie 750 ( WAGO-I/O-SYST EM)/Monti eren/D emonti eren/Ger äte ei nfügen - Ü berschrift 2 @ 16\mod_1378817340508_21.doc x @ 131074 @ 2 @ 1
5.6
Inserting Devices
Pos : 34.16 /Alle Serien (Allgemeine M odul e)/Sic herheits- und sonstige Hinweis e/Achtung/Ac htung: Arbeiten an Geräten nur s pannungsfrei durchführen! @ 6\mod_1256193963573_21.doc x @ 43426 @ @ 1
Perform work on devices only if they are de-energized!
Working on energized devices can damage them. Therefore, turn off the power
supply before working on the devices.
Pos : 34.17 /Serie 750 ( WAGO-I/O-SYST EM)/Monti eren/D emonti eren/PFC-Contr oller (XTR) ei nfügen @ 24\mod_1446646433987_21.doc x @ 194968 @ 3 @ 1
5.6.1
Inserting the Controller
1.
When replacing the controller for an already available controller, position
the new controller so that the tongue and groove joints to the subsequent I/O
module are engaged.
2.
Snap the controller onto the carrier rail.
3.
Use a screwdriver blade to turn the locking disc until the nose of the locking
disc engages behind the carrier rail (see the following figure). This prevents
the controller from canting on the carrier rail.
With the controller snapped in place, the electrical connections for the data
contacts and power contacts (if any) to the possible subsequent I/O module are
established.
Pos : 34.18 /Serie 750 ( WAGO-I/O-SYST EM)/Monti eren/D emonti eren/Verrieg elung - Bil d (Contr oller PFC xxx) XTR @ 24\mod_1441789683702_21.doc x @ 191048 @ @ 1
Figure 21: Release Tab of Controller (Example)
Pos : 34.19 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Mounting
75
Pos : 34.20 /Serie 750 ( WAGO-I/O-SYST EM)/Monti eren/D emonti eren/Bus kl emme einfügen @ 3\mod_1231769726703_21.doc x @ 25989 @ 3 @ 1
5.6.2
Inserting the I/O Module
1.
Position the I/O module so that the tongue and groove joints to the fieldbus
coupler/controller or to the previous or possibly subsequent I/O module are
engaged.
Figure 22: Insert I/O Module (Example)
2.
Press the I/O module into the assembly until the I/O module snaps into the
carrier rail.
Figure 23: Snap the I/O Module into Place (Example)
With the I/O module snapped in place, the electrical connections for the data
contacts and power jumper contacts (if any) to the fieldbus coupler/controller or to
the previous or possibly subsequent I/O module are established.
Pos : 35 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
76
Connect Devices
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 36 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 1/Geräte ansc hließ en - Übersc hrift 1 @ 3\mod_1234172889468_21.doc x @ 27460 @ 1 @ 1
6
Connect Devices
Pos : 37 /All e Seri en (Allgemei ne Module)/Wic htige Erläuterungen/Sicherheits- und s ons tige Hi nweis e/Gefahr/Gefahr: Lei tungen nur i n s pannungsfr eiem Zus tand ansc hliessen oder trennen @ 16\mod_1372153982130_21.doc x @ 124277 @ @ 1
Only connect or disconnect lines when power is safely isolated!
The lines to the device can carry hazardous voltages and currents. Contact with
the lines when live can result in severe injury or death. Therefore, read and
observe the following safety rules before you perform work on the device:
1.
Disconnect the respective system component from the power supply.
2.
Secure the system component against unintentional restart.
3.
Check if the voltage is positively isolated.
Pos : 38.1 /Serie 750 (WAGO-I/O-SYST EM)/Ans chli eßen/Leis tungs kontakte/Fel dversorgung - Ü bersc hrift 2 @ 7\mod_1266320656354_21.doc x @ 50722 @ 2 @ 1
6.1
Power Contacts/Field Supply
Pos : 38.2 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/Vorsic ht/Vorsicht: Verl etz ungsgefahr durc h s charfkantige M ess er kontakte! @ 6\mod_1256193279401_21.doc x @ 43414 @ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury.
Pos : 38.3 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Ansc hl üsse/Leistungs kontakte allgemei n @ 3\mod_1231828902046_21.doc x @ 26017 @ @ 1
Self-cleaning power jumper contacts used to supply the field side are located on
the right side of most of the fieldbus couplers/controllers and on some of the I/O
modules. These contacts come as touch-proof spring contacts. As fitting
counterparts the I/O modules have male contacts on the left side.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Figure 24: Example for the Arrangement of Power Contacts
Pos : 38.4 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Connect Devices
77
78
Connect Devices
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 38.5 /Serie 750 (WAGO-I/O-SYST EM)/Ans chli eßen/Lei ter an C AGE C LAM P ans chließen (Ei ns peis ung) - Übersc hrift 2 und T ext @ 17\mod_1382360262114_21.doc x @ 134719 @ 2 @ 1
6.2
Connecting a Conductor to the CAGE CLAMP®
The WAGO CAGE CLAMP® connection is appropriate for solid, stranded and
finely stranded conductors.
Select conductor cross sections as required for current load!
The current consumed for field-side supply may not exceed 10 A. The wire cross
sections must be sufficient for the maximum current load for all of the I/O
modules to be supplied with power.
Only connect one conductor to each CAGE CLAMP® connection!
Only one conductor may be connected to each CAGE CLAMP® connection.
Do not connect more than one conductor at one single connection!
If more than one conductor must be routed to one connection, these must be
connected in an up-circuit wiring assembly, for example using WAGO feedthrough terminals.
1.
To open the CAGE CLAMP® insert the actuating tool into the opening
above the connection.
2.
Insert the conductor into the corresponding connection opening.
3.
To close the CAGE CLAMP® simply remove the tool - the conductor is
then clamped firmly in place.
Figure 25: Connecting a Conductor to a CAGE CLAMP®
Pos : 38.6 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Connect Devices
79
Pos : 38.7 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/N eue Ü berschriften/Ebene 2Eins peisekonz ept - Ü bersc hrift 2 @ 9\mod_1292323902755_21.doc x @ 67445 @ 2 @ 1
6.3
Power Supply Concept
Pos : 38.8 /Serie 750 (WAGO-I/O-SYST EM)/Systembesc hrei bung/Vers orgung/Ergänz ende Ei ns peis evorsc hriften XTR ( Standard) @ 16\mod_1373896786700_21.doc x @ 126194 @ 3 @ 1
6.3.1
Supplementary Power Supply Regulations
The WAGO-I/O-SYSTEM 750 XTR can also be used in shipbuilding applications
and onshore/offshore installations (e.g., platforms, loading facilities), as well as in
telecontrol applications. This is possible via certification under the standards of
leading agencies such as Germanischer Lloyd and Lloyds Register.
For standard-compliant application in substation instrumentation and control,
telecontrol systems, railway technology or shipbuilding certified operation, fieldside power supply filter 750-624/040-001 or power supply filter 750-626/040-000
are generally to be used for XTR module groups.
Table 37: Filter Modules for 24 V Power Supply
Item No.
750-626/040-000
Description
Power supply
filter
750-624/040-001
Field-side
power supply
filter
Description
System and field supply with filtering (24 V,
0 V), i.e., fieldbus coupler/controller and bus
power supply (750-613/040-000)
24 V field supply with filtering
Therefore, the following power supply requirements must be observed:
Figure 26: Power Supply Concept
The 24 V system power supply for the fieldbus coupler/controller must be filtered
and protected against overvoltage. Therefore, the power must be supplied via
power supply filter 750-626/040-000.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
80
Connect Devices
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
The 24 V field power supply systems must be protected against overvoltage.
Therefore, the power must be supplied via field-side power supply filter
750-624/040-001 or power supply filter 750-626/ 040-000.
For this potential group, only the supply module 750-612/040-000 is required for
a 230 V field power supply.
Pos : 38.9 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Connect Devices
81
Pos : 38.10 /Serie 750 ( WAGO-I/O-SYST EM)/Systembesc hrei bung/Vers orgung/Vers orgungsbeispi el - Ü bers chrift + Hinweis @ 3\mod_1232949833531_21.doc x @ 26670 @ 3 @ 1
6.3.2
Supply Example
Suppl Sggggggggggggggggg
The system supply and the field supply shall be separated!
You should separate the system supply and the field supply in order to ensure bus
operation in the event of a short-circuit on the actuator side.
Pos : 38.11 /Serie 750 ( WAGO-I/O-SYST EM)/Systembesc hrei bung/Vers orgung/Vers orgungsbeispi el - Bild XTR @ 18\mod_1393260466178_21.doc x @ 146269 @ @ 1
Figure 27: Power Supply Example
Pos : 38.12 /Serie 750 ( WAGO-I/O-SYST EM)/Systembesc hrei bung/Vers orgung/Vers orgungsbeispi el - Leg ende z u Abbildung " Versorgungsbeis piel XTR" @ 18\mod_1393260531676_21.doc x @ 146272 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
82
Connect Devices
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 38: Legend for Figure “Power Supply Example”
Item
1
2
3
4
5
Description
Power supply on the fieldbus coupler/controller via external system
supply module
Supply module 24 V
Supply module with bus power supply 24 V
Separation module recommended
Supply module 230 V
Pos : 38.13 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Connect Devices
83
Pos : 38.14 /Serie 750 ( WAGO-I/O-SYST EM)/Systembesc hrei bung/Vers orgung/N etzg eräte XTR @ 16\mod_1373963895846_21.doc x @ 126216 @ 3 @ 1
6.3.3
Power Supply Units
The WAGO-I/O-SYSTEM 750 XTR requires 24 VDC voltage (system supply)
for operation.
Recommendation
A stable power supply cannot always be assumed everywhere. Therefore, you
should use regulated power supplies to ensure the quality of the supply voltage
(see also table “WAGO power supply units”).
For brief voltage dips, a buffer (200 µF per 1 A load current) must be provided.
Buffer for system power supply!
The system power supply must be buffered to bridge power outages. As the power
demand depends on the respective node configuration, buffering is not
implemented internally.
To achieve power outages of 1 ms to 10 ms according to IEC61131-2, determine
the buffering appropriate for your node configuration and structure it as an
external circuit.
The power demand must be determined individually depending on the entry point
of the field supply. All loads through field devices and I/O modules must be taken
into account. The field supply also impacts the I/O modules because the input and
output drivers of some I/O modules require the voltage of the field supply.
System and field supply must be isolated!
The system supply and field supply must be isolated to ensure bus operation in the
event of short circuits on the actuator side.
Table 39: WAGO Power Supply Units
Item number
Description
787-822/xxx-xxx Primary switch-mode power supply EPSITRON® PRO Power,
24 VDC / 5 A*), nominal input voltage 100 VAC … 240 VAC
787-832/xxx-xxx Primary switch-mode power supply EPSITRON® PRO Power,
24 VDC / 10 A*), nominal input voltage 110 VAC … 240 VAC
787-840/xxx-xxx Primary switch-mode power supply EPSITRON® PRO Power,
24 VDC / 10 A*), nominal input voltage 3×
400 VAC … 500 VAC
*)
Derating −3 %/K > +50 °C
Pos : 38.15 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
84
Connect Devices
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 38.16 /Serie 750 ( WAGO-I/O-SYST EM)/Systembesc hrei bung/Vers orgung/Erdung @ 3\mod_1231246555687_21.doc x @ 25802 @ 23443 @ 1
6.4
Grounding
6.4.1
Grounding the DIN Rail
6.4.1.1
Framework Assembly
When setting up the framework, the carrier rail must be screwed together with the
electrically conducting cabinet or housing frame. The framework or the housing
must be grounded. The electrical connection is established via the screw. Thus,
the carrier rail is grounded.
Ensure sufficient grounding is provided!
You must take care to ensure the flawless electrical connection between the
carrier rail and the frame or housing in order to guarantee sufficient grounding.
6.4.1.2
Insulated Assembly
Insulated assembly has been achieved when there is constructively no direct
ohmic contact between the cabinet frame or machine parts and the carrier rail.
Here, the earth ground must be set up via an electrical conductor in accordance
with valid national safety regulations.
Recommendation
The optimal setup is a metallic assembly plate with grounding connection which
is electrically conductive linked to the carrier rail.
The separate grounding of the carrier rail can be easily set up with the aid of the
WAGO ground wire terminals.
Table 40: WAGO Ground Wire Terminals
Order No. Description
283-609
1-conductor ground (earth) terminal block make an automatic contact
to the carrier rail; conductor cross section: 0.2 mm² … 16 mm2
Note: Also order the end and intermediate plate (283-320).
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
6.4.2
Connect Devices
85
Grounding Function
The grounding function increases the resistance against electro-magnetic
interferences. Some components in the I/O system have a carrier rail contact that
dissipates electro-magnetic interferences to the carrier rail.
Figure 28: Carrier Rail Contact (Example)
Ensure sufficient grounding is provided!
You must take care to ensure the direct electrical connection between the carrier
rail contact and the carrier rail.
The carrier rail must be grounded.
For information on carrier rail properties, see section “Mounting” > … > “Carrier
Rail Properties”.
The bottom CAGE CLAMP® connectors of the supply modules enable optional
connection of a field-side functional ground. This potential is made available to
the I/O module arranged on the right through the spring-loaded contact of the
three power contacts. Some I/O modules are equipped with a knife-edge contact
that taps this potential. This forms a potential group with regard to functional
ground with the I/O module arranged on the left.
Pos : 38.17 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
86
Connect Devices
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 38.18 /Serie 750 ( WAGO-I/O-SYST EM)/Systembesc hrei bung/Vers orgung/Sc hirmung @ 3\mod_1231251994828_21.doc x @ 25813 @ 23333 @ 1
6.5
Shielding
6.5.1
General
Use of shielded cables reduces electromagnetic interference and thus increases
signal quality. Measurement errors, data transmission errors and interference due
to excessive voltage can be prevented.
Connect the cable shield to the ground potential!
Integrated shielding is mandatory to meet the technical specifications in regards to
measuring accuracy. Connect the cable shield and ground potential at the inlet to
the cabinet or housing. This allows induced interference to dissipate and to be
kept away from devices in the cabinet or housing.
Figure 29: Cable Shield at Ground Potential
Improve shielding performance by placing the shield over a large area!
Higher shielding performance is achieved via low-impedance connection between
shield and ground. For this purpose, connect the shield over a large surface area,
e.g., WAGO shield connecting system. This is especially recommended for largescale systems where equalizing current or high impulse-type currents caused by
atmospheric discharge may occur.
Keep data and signal lines away from sources of interference!
Route data and signal lines separately from all high voltage cables and other
sources of high electromagnetic emission (e.g., frequency converter or drives).
6.5.2
Bus Cables
The shielding of the bus line is described in the respective configuration
guidelines and standards of the bus system.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
6.5.3
Connect Devices
87
Signal Lines
I/O modules for analog signals and some interface I/O modules are equipped with
shield clamps.
Use shielded signal lines!
Only use shielded signal lines for analog signals and I/O modules which are
equipped with shield clamps. Only then can you ensure that the accuracy and
interference immunity specified for the respective I/O module can be achieved
even in the presence of interference acting on the signal cable.
6.5.4
WAGO Shield Connecting System
The WAGO shield connecting system consists of shield clamping saddles,
busbars and various mounting carriers. These components can be used to achieve
many different configurations.
Figure 30: Examples of the WAGO Shield Connecting System
Figure 31: Application of the WAGO Shield Connecting System
Pos : 38.19 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
88
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 39 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Pos : 40 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 1/In Betri eb nehmen - Ü bersc hrift 1 @ 4\mod_1240901452750_21.doc x @ 31570 @ 1 @ 1
7
Commissioning
Pos : 41.1 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/In Betrieb nehmen 750-8xxx - Einsc halten des C ontroll ers - allgemei n @ 21\mod_1418632393377_21.doc x @ 170398 @ 2 @ 1
7.1
Switching On the Controller
Before switching on the controller ensure that you
•
have properly installed the controller
(see section “Installation”),
•
have connected all required data cables (see section “Connections”) to the
corresponding interfaces and have secured the connectors by their attached
locking screws,
•
have connected the electronics and field-side power supply
(see section “Connections”),
•
have mounted the end module (750-600)
(see Section “Installation”),
•
have performed appropriate potential equalization at your machine/system
(see System Description for 750-xxx) and
•
have performed shielding properly (see System Description for 750-xxx).
To switch on both the controller and the connected I/O modules, switch on your
power supply unit.
Starting of the controller is indicated by a brief green flashing of all LEDs. After a
few seconds the SYS LED will signal successful boot-up of the controller.
The CODESYS 2.3 runtime system or e!RUNTIME is started at the same time.
Pos : 41.2 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/In Betrieb nehmen 750-82xx - Ei nsc halten des Contr ollers - C ODESYS 2 und e!RUNTIM E @ 21\mod_1418137679896_21.doc x @ 170200 @ @ 1
Once the entire system has been successfully started, the SYS and I/O LEDs light
up green.
If there is an executable IEC 61131-3 program stored and running on the
controller, the RUN LED will light up green.
If no executable program is stored on the controller, or the mode selector switch is
set to STOP, this is likewise indicated by the RUN LED (see Section
“Diagnostics”> … > “Fieldbus/System Indication Elements”).
Pos : 41.3 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
89
Pos : 41.4 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/In Betrieb nehmen 750-8xxx - IP-Adresse er mittel n, eins tell en, mit D HCP zuweis en @ 14\mod_1360311371851_21.doc x @ 111200 @ 223 @ 1
7.2
Determining the IP Address of the Host PC
To ensure that the host PC can communicate with the controller via ETHERNET,
both devices must be located in the same subnet.
To determine the IP address of the host PC (with the Microsoft Windows®
operating system) using the MS DOS prompt, proceed as follows:
1.
Open the MS DOS prompt window.
To do this, enter the command “cmd” in the input field under Start >
Execute… > Open: (Windows® XP) or Start > Search programs/files
(Windows® 7) and then click [OK] or press [Enter].
2.
In the MS DOS prompt enter the command “ipconfig” and then press
[Enter].
3.
The IP address, subnet mask and standard gateway, including the
appropriate parameters, are displayed.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
90
7.3
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Setting an IP Address
In the controller's initial state the following IP addresses are active for the
ETHERNET interface (Port X1 and Port X2):
Table 41: Default IP Addresses for ETHERNET Interfaces
Ethernet interface
X1/X2
Default setting
Dynamic assignment of IP address using “Dynamic Host
Configuration Protocol” (DHCP)
Adapt IP addressing for your specific system structure to ensure that the PC and
the controller can communicate with one another using one of the available
configuration tools (WBM, “WAGO Ethernet Settings”, CBM) (see section
“Configuration”).
Example for incorporating the controller (192.168.2.17) into an existing
network:
If the IP address of your host PC is 192.168.1.2, for example, then the controller
must be on the same subnet. That is, with the net mask 255.255.255.0, the first
three digits of the controller must match those of your PC. This yields the
following address range for the controller:
Table 42: Network Mask 255.255.255.0
Host PC
192.168.1.2
Subnet address range for the controller
192.168.1.3 … 192.168.1.254
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.3.1
Commissioning
91
Assigning an IP Address using DHCP
The Controller can obtain dynamic IP addresses from a server (DHCP/BootP).
In contrast to fixed IP addresses, dynamically assigned addresses are not stored
permanently. Therefore, a BootP or DHCP server must be available each time the
controller is restarted.
If an IP address has been assigned by means of DHCP (default setting), it can be
determined through the settings and the output of the specific DHCP server.
In the example figure shown here, the corresponding output of “Open DHCP” is
presented.
Figure 32: “Open DHCP”, Example Figure
In conjunction with the DNS server associated with DHCP, the device can be
reached using its host name.
This name consists of the prefix “PFCx00-“ and the last six places of the MAC
address (in the example shown here: “00:30:DE:FF:00:5A”). The MAC address of
the device can be printed on the label on the side of the device.
The host name of the device in the example shown here is thus “PFC200FF005A”.
Pos : 41.5 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
92
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 41.6 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/In Betrieb nehmen 750-8xxx - IP-Adresse änder n mit 'CBM' über s eriell e Schnittstelle @ 17\mod_1383200410146_21.doc x @ 136357 @ 3 @ 1
7.3.2
Changing an IP Address Using the “CBM” Configuration
Tool via the Serial Interface
You can also assign a new IP address to the ETHERNET interfaces X1 and X2
using the “CBM” configuration tool provided on the Linux® console. More
information about “CBM” is given in the Section “Configuration.”
1.
Link a PC to the X3 serial interface using a terminal program.
2.
Log in to the Linux® system as a “super user.”
The user name and the password are provided in the Section “Users and
Passwords” > “Linux® User Group.”
3.
Start the configuration tool by entering the command “cbm” on the
command line and then press [Enter].
Figure 33: CBM Starting Screen
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
4.
Commissioning
In the Main menu use the keyboard (arrow keys or numeric keypad) to
move to and select Networking and then press [Enter].
Figure 34: CBM – Selecting “Networking”
5.
In the Networking menu select TCP/IP and press [Enter].
Figure 35: CBM – Selecting “TCP/IP”
6.
In the menu TCP/IP select IP Address and press [Enter].
Figure 36: CBM – Selecting “IP address”
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
93
94
Commissioning
7.
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
In the menu TCP/IP Configuration select IP Address and press [Enter].
Figure 37: CBM – Selecting the IP Address
8.
In the menu Change IP Address enter the new IP address and confirm by
clicking [OK]. If you want to return to the main menu without making
changes, click [Abort].
Figure 38: CBM – Entering a New IP Address
Pos : 41.7 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
95
Pos : 41.8 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/In Betrieb nehmen 750-8xxx - IP-Adresse änder n mit ' WAGO Ethernet Setti ngs' @ 17\mod_1383200333255_21.doc x @ 136353 @ 3 @ 1
7.3.3
Changing an IP Address using “WAGO Ethernet Settings”
The Microsoft Windows® application “WAGO Ethernet Settings” is a software
used to identify the controller and configure network settings.
Observe the software version!
To configure the controller use at least Version 6.4.1.1 dated 2015-06-29 of
“WAGO Ethernet Settings”!
You can use WAGO communication cables or WAGO radio adapters or even the
IP network for data communication.
1.
Switch off the power supply to the controller.
2.
Connect the 750-920 communication cable to the Service interface on the
controller and to a serial interface of your PC.
3.
Switch the power supply to the controller on again.
4.
Start the “WAGO Ethernet Settings” program.
Figure 39: “WAGO Ethernet Settings” – Starting Screen (Example)
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
96
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
5.
Click [Identify] to read in and identify the connected controller.
6.
Select the “Network” tab:
Figure 40: “WAGO Ethernet Settings” – “Network” Tab
7.
To assign a fixed address, select “Static configuration” on the “Source” line
under “Input”. DHCP is normally activated as the default setting.
8.
In the column “Input” enter the required IP address and, if applicable, the
address of the subnet mask and of the gateway.
9.
Click on [Write] to accept the address in the controller. (If necessary,
“WAGO Ethernet Settings” will restart your controller. This action may
require about 30 seconds.)
10.
You can now close “WAGO Ethernet Settings”, or make other changes
directly in the Web-based Management system as required. To do this, click
on [WBM] at the right in the window.
Pos : 41.9 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
97
Pos : 41.10 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/In Betrieb nehmen 750- 8xxx - Temporär eine fes te IP- Adr ess e eins tell en @ 19\mod_1402045404984_21.doc x @ 155365 @ 3 @ 1
</dg_
7.3.4
Temporarily Setting a Fixed IP Address
This procedure temporarily sets the IP address for the X1 interface to the fixed
address “192.168.1.17”.
When the switch is enabled, the fixed address is also used for interface X2.
When the switch is disabled, the original address setting for interface X2 is not
changed.
No reset is performed.
To make this setting, set the mode selector switch to STOP and press and hold the
Reset button (RST) for longer than 8 seconds.
Execution of the setting is signaled by the “SYS” LED flashing orange.
To cancel this setting, perform a software reset or switch off the controller and
then switch it back on.
Pos : 41.11 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
98
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 41.12 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/In Betrieb nehmen 750- 8xxx - Netz werkver bindung testen @ 17\mod_1383200162192_21.doc x @ 136349 @ 2 @ 1
7.4
Testing the Network Connection
Carry out a ping network function to check whether you can reach the controller
at the IP address you have assigned in the network.
1.
Open the MS DOS prompt window.
To do this, enter the command “cmd” in the input field under Start >
Execute… > Open: (Windows® XP) or Start > Search programs/files
(Windows® 7) and then click [OK] or press [Enter].
2.
In the MS DOS window, enter the command “ping” and the IP address of
the controller (for example, ping 192.168.1.17)and then press
[Enter].
Host entries in the ARP table!
It may also be useful to delete the current host entries in the ARP table with the
command “arp -d *” before executing the “ping” command (as administrator in
Windows® 7). This ensures that older entries will not impair the success of the
“ping” command.
3.
Your PC sends out a query that is answered by the controller. This reply
appears in the MS DOS prompt window. If the error message “Timeout”
appears, the controller has not responded properly. You then need to check
your network settings.
Figure 41: Example of a Function Test
4.
If the test is completed successfully, close the MS DOS window.
Pos : 41.13 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
99
Pos : 41.14 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/In Betrieb nehmen 750- 8xxx - Standar dpass wörter änder n @ 21\mod_1423661984306_21.doc x @ 174158 @ 2 @ 1
7.5
Changing Standard Passwords
Change passwords
The standard passwords are documented in these instructions and therefore do not
offer adequate protection! Change the passwords to meet your particular needs!
To increase security all passwords should contain a combination of lower case
letters (a … z), upper case letters (A … Z), numbers (0 … 9), spaces and special
characters: (]!"#$%&'()*+,./:;<=>?@[\^_`{|}~-). Passwords should not contain
generally known names, dates of birth and other information that is easy to guess.
Therefore change the standard passwords before commissioning the controller.
Standard passwords are issued for the user groups “WBM Users” and “Linux®
Users.”
The table in the Section “Function Description” > ... > “Users and Passwords” >
“WBM Users Group” shows the standard passwords for the WBM users. Proceed
as follows to change these passwords:
1.
Connect the controller to a PC via one of the network interfaces (X1, X2).
2.
Start a web browser program on the PC and call up the WBM of the
controller.
3.
Log in on the controller as “admin” user with the standard password.
4.
Change the password for all users on the WBM “Configuration of the users
for the WBM” page.
5.
Select each user and enter a new password and confirm it.
The table in the Section “Functional Description” > ... > “Users and Passwords” >
“Linux® Users Group” shows the standard passwords for the Linux® users.
Proceed as follows to change these passwords:
1.
Connect the controller to a PC via the serial interface (X3).
2.
Start a terminal program on the PC.
3.
Log in on the controller as user “root” with the standard password.
4.
Change the password for all users with the “passwd root,” “passwd admin”
and “passwd user” commands.
Pos : 41.15 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
100
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 41.16 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/In Betrieb nehmen 750- 8xxx - Aussc halten, Neus tarten @ 21\mod_1418137580940_21.doc x @ 170188 @ 2 @ 1
</dg_
7.6
Shutdown/Restart
Switch off the power supply to shut down the controller.
To perform a controller restart, press the Reset button as described in the Section
“Triggering Reset Functions” > “Software Reset (Restart).”
Alternatively, you can switch off the controller and switch it back on again.
Pos : 41.17 /Serie 750 ( WAGO-I/O-SYST EM)/Wichtig e Erl äuter ung en/Sic her hei ts- und s onstige Hinweise/Hinweis/Hi nweis : N eus tart nac h Par ameter änderungen nic ht durc h Aus- und Wi eder einsc halten her vorrufen! @ 25\mod_1456905013311_21.doc x @ 203078 @ @ 1
Do not power cycle the controller after changing any parameters!
Some parameter changes require a controller restart for the changes to apply.
Saving changes takes time.
Do not power cycle the controller to perform a restart, i.e., changes may be lost by
shutting down the controller too soon.
Only restart the controller using the software reboot function. This ensures that all
memory operations are completed correctly and completely.
Pos : 42 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
101
Pos : 43.1 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/R es et-F unktionen auslösenR eset-Funkti onen ausl ös en 750-8xxx - Ei nlei tung @ 19\mod_1402044132075_21.doc x @ 155337 @ 2 @ 1
</dg_
7.7
Initiating Reset Functions
You can initiate various reset functions using the mode selector switch and the
Reset button (RST).
Pos : 43.2 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/R es et-F unktionen auslösenR eset-Funkti onen ausl ös en 750-8xxx - War ms tart - Übersc hrift 3 @ 19\mod_1404997479559_21.doc x @ 158448 @ 3 @ 1
7.7.1
Warm Start Reset
Pos : 43.3 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/R es et-F unktionen auslösen/R es et-Funktionen auslös en 750-8xxx - Warmstart - Einl eitung - Ergänz ung Laufz eits ys tem @ 19\mod_1404999941457_21.doc x @ 158499 @ @ 1
The warm start reset function depends on the activated runtime system
(CODESYS 2 or e!RUNTIME).
Pos : 43.4 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/N eue Ü berschriften/Ebene 4Laufzeits ystem C ODESYS 2 - Ü berschrift 4 @ 19\mod_1404997478951_21.doc x @ 158374 @ 4 @ 1
7.7.1.1
CODESYS 2 Runtime System
Pos : 43.5 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/R es et-F unktionen auslösenR eset-Funkti onen ausl ös en 750-8xxx - War ms tart - Besc hrei bung, C ODESYS 2 @ 19\mod_1402044135866_21.doc x @ 155341 @ @ 1
</dg_
The CODESYS 2 application is reset on a warm start reset. This corresponds to
the WAGO I/O PRO IDE “Reset” command.
Pos : 43.6 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/R es et-F unktionen auslösenR eset-Funkti onen ausl ös en 750-8xxx - War ms tart - Durc hführung @ 19\mod_1402044140046_21.doc x @ 155345 @ @ 1
</dg_
To perform a warm start reset, set the mode selector switch to "Reset" and hold it
there for two to seven seconds.
Execution of the reset is signaled by the red “RUN LED” briefly going out when
the mode selector switch is released.
Pos : 43.7 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/N eue Ü berschriften/Ebene 4Laufzeits ystem e!RUNTIME - Ü berschrift 4 @ 19\mod_1404997480277_21.doc x @ 158452 @ 4 @ 1
7.7.1.2
e!RUNTIME Runtime System
Pos : 43.8 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/R es et-F unktionen auslösenR eset-Funkti onen ausl ös en 750-8xxx - War ms tart - Besc hrei bung, e!RUNTIME @ 19\mod_1402045406045_21.doc x @ 155393 @ @ 1
All e!RUNTIME applications are reset with a warm start reset. All global data is
set to its initialization values. This corresponds to the e!COCKPIT IDE “Reset
warm” command.
Pos : 43.9 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/R es et-F unktionen auslösenR eset-Funkti onen ausl ös en 750-8xxx - War ms tart - Durc hführung @ 19\mod_1402044140046_21.doc x @ 155345 @ @ 1
</dg_
To perform a warm start reset, set the mode selector switch to "Reset" and hold it
there for two to seven seconds.
Execution of the reset is signaled by the red “RUN LED” briefly going out when
the mode selector switch is released.
Pos : 43.10 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/R es et-Funkti onen auslös enRes et-F unktionen ausl ösen 750- 8xxx - Kaltstart - Übersc hrift 3 @ 19\mod_1404997478077_21.doc x @ 158370 @ 3 @ 1
7.7.2
Cold Start Reset
Pos : 43.11 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/R es et-Funkti onen auslös en/R eset-Funkti onen ausl ös en 750-8xxx - Kalts tart - Ei nlei tung - Ergänz ung Laufzei ts ystem @ 19\mod_1404999083172_21.doc x @ 158485 @ @ 1
The cold start reset function depends on the activated runtime system (CODESYS
2 or e!RUNTIME).
Pos : 43.12 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 4Laufz eits ystem COD ESYS 2 - Ü bersc hrift 4 @ 19\mod_1404997478951_21.doc x @ 158374 @ 4 @ 1
7.7.2.1
CODESYS 2 Runtime System
Pos : 43.13 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/R es et-Funkti onen auslös enRes et-F unktionen ausl ösen 750- 8xxx - Kaltstart - Besc hrei bung, C ODESYS 2 @ 19\mod_1402044143806_21.doc x @ 155349 @ @ 1
</dg_
On a cold start reset the CODESYS 2 application is reset and the memory
containing the retain variables is cleared.
This corresponds to the WAGO I/O PRO IDE “Reset (Cold)” command.
Pos : 43.14 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/R es et-Funkti onen auslös enRes et-F unktionen ausl ösen 750- 8xxx - Kaltstart - Durc hführ ung @ 19\mod_1402044153290_21.doc x @ 155353 @ @ 1
</dg_
To perform a cold start reset, set the mode selector switch to “Reset” and hold it
there for more than seven seconds.
Execution of the reset is signaled after seven seconds by the “RUN” LED going
out for an extended period. You can then release the mode selector switch.
Pos : 43.15 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Neue Ü bersc hriften/Ebene 4Laufz eits ystem e!RUNTIM E - Ü bersc hrift 4 @ 19\mod_1404997480277_21.doc x @ 158452 @ 4 @ 1
7.7.2.2
e!RUNTIME Runtime System
Pos : 43.16 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/R es et-Funkti onen auslös enRes et-F unktionen ausl ösen 750- 8xxx - Kaltstart - Besc hrei bung, e!RUNTIME @ 19\mod_1402045405530_21.doc x @ 155389 @ @ 1
</dg_
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
102
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
All e!RUNTIME applications are reset with a cold start reset. All global data and
the retain variables are set to their initialization values.
This corresponds to the e!COCKPIT IDE “Reset Cold” command.
Pos : 43.17 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/R es et-Funkti onen auslös enRes et-F unktionen ausl ösen 750- 8xxx - Kaltstart - Durc hführ ung @ 19\mod_1402044153290_21.doc x @ 155353 @ @ 1
</dg_
To perform a cold start reset, set the mode selector switch to “Reset” and hold it
there for more than seven seconds.
Execution of the reset is signaled after seven seconds by the “RUN” LED going
out for an extended period. You can then release the mode selector switch.
Pos : 43.18 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/R es et-Funkti onen auslös enRes et-F unktionen ausl ösen 750- 8xxx - Software-R es et (N eustar t) - Besc hrei bung und D urchführung @ 15\mod_1370511679721_21.doc x @ 122010 @ 3 @ 1
</dg_
7.7.3
Software Reset
The controller is restarted on a software reset.
To perform a software reset, set the mode selector switch to RUN or STOP and
then press the Reset button (RST) for one to eight seconds.
All LEDs will light up briefly in green to signal reset completion.
Pos : 44 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
103
Pos : 45 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 2/Konfigurieren - Ü bersc hrift 2 @ 12\mod_1339747993273_21.doc x @ 97680 @ 2 @ 1
7.8
Configuration
Pos : 46 /Serie 750 ( WAGO-I/O-SYST EM)/In Betrieb nehmen/Konfigurieren 750- 8xxx - Ei nleitung mi t R S-232 @ 14\mod_1361451959475_21.doc x @ 112610 @ @ 1
The following methods are available for configuring the controller:
•
Access to the Web-based management system via the PC using an Internet
browser (“Configuration using Web-Based Management (WBM)”)
•
Access to the “Console-Based Management” system (CBM) via the PC
using a terminal program (via ETHERNET and/or RS-232 interface)
(“Configuration using a Terminal Program”)
•
Access via the CODESYS PLC program using the WagoConfigToolLIB.lib
library (“Appendix” > “WagoConfigToolLIB.lib”)
•
Access via the PC using “WAGO Ethernet Settings” (“Configuration using
'WAGO Ethernet Settings'”).
The CBM basically provides the same parameters for configuration of the
controller as the WBM, except for parameters which cannot be represented in a
useful manner in a terminal window.
For an explanation of these parameters refer to the sections starting at
“'Information' Page”.
Pos : 47 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
104
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 48 /Serie 750 ( WAGO-I/O-SYST EM)/In Betrieb nehmen/Konfigurieren 750- 8xxx mi t WBM >= F W04 @ 20\mod_1413527855844_21.doc x @ 166046 @ 34 @ 1
7.8.1
Configuration via Web-Based-Management (WBM)
The HTML pages (from here on referred to as “pages”) of the Web-Based
Management are used to configure the controller. Proceed as follows to access the
WBM using an Internet browser:
1.
Connect the controller to the ETHERNET network via the ETHERNET
interface X1.
2.
To access the pages, enter the controller's IP address in the address line of
your browser followed by “/wbm,” e.g., “http://192.168.1.17/wbm.” Note
that the PC and the controller must be located within the same subnet (see
Section “Setting an IP Address”). If you do not know the IP address and
cannot determine it, switch the controller to the pre-set address
“192.168.1.17” using the “Fixed IP address” function (see Section “Initiate
Reset Functions” > “Set Fixed IP Address”).
If you have installed a DHCP server on your PC and would like to access WBM
through DHCP, use the other interface. You can find detailed information about
this in the section “Assigning an IP Address Using DHCP.”
Displaying the Controller Start Page
If the controller does not display the start page, ensure that your Internet browser
settings permit the bypassing of the proxy server for local addresses. Also check
whether your PC is located in the same subnet as the controller.
Take usage by the CODESYS program into account
If the controller is at capacity due to a CODESYS program, this may result in
slower processing in the WBM. As a result, timeout errors are sometimes reported
in some circumstances. It is therefore important to stop the CODESYS application
prior to performing complicated configurations using WBM.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
105
Some pages of the WBM are accessible only for certain users. They are only
displayed if you have logged into the WBM. You can access the login form via
the “Login” link. Pages which cannot be accessed with your current user name are
already grayed out in the navigation. You can nevertheless select the entries in the
navigation bar and are then routed directly to the login form.
As soon as you have logged in, your current user name is displayed in the header
of the WBM. By clicking the “Logout” link you can log out again and then log in
again with a different user name. When using the WBM without logging in, you
are granted “Guest” access rights.
You must be logged into the WBM in order to have write or read access to (most)
parameters. This is checked with every access to the device.
If you have disabled cookies in your browser, you can continue to use the WBM
as long as you move directly inside it. However, if you fully reload the website
(e.g., with F5), you must log in again since the browser is then not able to store
the data of your login session.
Figure 42: Entering Authentication
7.8.1.1
WBM User Administration
To allow settings to be made only by a select number of users, limit access to
WBM functions through User Administration.
Change passwords
The standard passwords are documented in these instructions and thus do not
offer adequate protection. Change the passwords to meet your particular needs.
See Section “Administration - Users Page.”
If you do not change these passwords, a warning will appear each time you call up
a website after logging in.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
106
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Figure 43: Password Reminder
Table 43: User Settings in the Default State
Users
user
admin
Password
user
wago
Observe access rights
Users in WBM are authorized exclusively for access to websites. User
administration for controller applications is configured separately.
Access to the WBM pages is as follows:
Pos : 49.1 /Serie 750 (WAGO-I/O-SYST EM)/Web-Bas ed-Management-System WBM/PFC xxxWBM PFC 200 Zugriffsr ec hte 750-82xx mi t RS- 232, ohne PR OFIBUS, >= F W06 @ 23\mod_1436430246272_21.doc x @ 185849 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
Table 44: Access Rights for WBM Pages
Navigation
Information
PLC Runtime
– Information
– General Configuration
– WebVisu
Networking
– Host/Domain Name
– TCP/IP
– Ethernet
Firewall
– General Configuration
– MAC Address Filter
– User Filter
Clock
Administration
– Users
– Create Image
– Serial Interface
– Service Interface
– Reboot
Package Server
– Firmware Backup
– Firmware Restore
– System Partition
Mass Storage
Software Uploads
Ports and Services
– Network Services
– NTP Client
– PLC Runtime Services
– SSH
– TFTP
– DHCP
– DNS
– MODBUS
SNMP
– General Configuration
– SNMP v1/v2c
– SNMP v3
Diagnostic
WBM page
Status Information
User
guest
PLC Runtime Information
General PLC Runtime Configuration
PLC WebVisu
guest
user
guest
Configuration of Host and Domain Name
TCP/IP Configuration
Ethernet Configuration
user
user
user
General Firewall Configuration
Configuration of MAC Address Filter
Configuration of User Filter
Configuration of Time and Date
user
user
user
user
Configuration of the users for the Webbased Management
Create bootable Image
Configuration of Serial Interface RS233
Configuration of Service Interface
Reboot Controller
admin
Firmware Backup
Firmware Restore
System Partition
Mass Storage
Software Uploads
admin
admin
admin
admin
admin
Configuration of Network Services
Configuration of NTP Client
Configuration of PLC Runtime Services
SSH Server Settings
TFTP Server
DHCP Configuration
Configuration of DNS Service
MODBUS Services Configuration
user
user
user
user
user
user
user
user
Configuration of general SNMP
parameters
Configuration of SNMP v1/v2c
parameters
Configuration of SNMP v3 Users
Diagnostic Information
admin
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
admin
admin
admin
admin
admin
admin
guest
107
108
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 44: Access Rights for WBM Pages
Navigation
OpenVPN / IPsec
WBM page
Configuration of OpenVPN / IPsec
User
admin
Pos : 49.2 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
109
Pos : 49.3 /Serie 750 (WAGO-I/O-SYST EM)/Web-Bas ed-Management-System WBM/PFC xxxWBM PFC xxx Allgemei ne Infos, >= FW04 @ 20\mod_1411540944808_21.doc x @ 164321 @ 4 @ 1
7.8.1.2
General Information about the Page
Figure 44: WBM Browser Window (Example)
The device name is displayed in the header of the browser window. When the user
has logged out, a [Login] button is displayed on the right in the header line, when
logged in a [Logout] button is displayed.
The navigation tree is shown on the left of the browser window. You can use this
navigation tree to go to the individual pages and, where provided, subpages
included in these pages. Some pages can only be called after a successful login.
To log in click the [Login] button and enter the user name and password in the
login window.
A status area with the following elements is displayed on the right:
Figure 45: WBM Status Information (Example)
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
110
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
•
WBM status:
This indicates whether the WBM is currently communicating with the
device in the background. In other words, one or more requests have been
sent and the browser is waiting for a response. Movement is then visible in
the graphic. This occurs when data is read on initial call-up of the page,
when the user has sent off a change form or when data is reloaded
automatically in cycles, e.g., the contents of the status area.
•
Local Time:
Local time on the device
•
Local Date:
Local date on the device
•
PLC Switch:
Setting of the mode selector switch
•
LEDs:
This indicates the status of the device LEDs. All LEDs are graphically
represented and are labeled with their particular designation (e.g., SYS,
RUN, ...). The following colors are possible:
- gray:
LED is off.
- full color (green, red, yellow, orange):
The LED is activated in the particular color.
half color:
The LED is flashing in the corresponding color. The other half of the
surface is then either gray or also colored. The latter case indicates that the
LED is flashing sequentially in different colors.
A tooltip containing more detailed information opens as long as the cursor is
positioned over an LED. The text that is displayed also contains the message
that put the LED into its current status. The time of the message is also
shown.
The states displayed in the WBM will not always correspond at the precise
time to those on the controller. Data has a runtime during transmission and
can only be queried at a certain interval. The time period between two
queries is 30 seconds.
The contents of the individual pages and sub-pages are explained in the following
sections.
Pos : 49.4 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/Hinweis/Hi nweis: N eustart nach Parameteränderungen nicht durc h Aus- und Wiedereinschalten her vorrufen! @ 25\mod_1456905013311_21.doc x @ 203078 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
111
Do not power cycle the controller after changing any parameters!
Some parameter changes require a controller restart for the changes to apply.
Saving changes takes time.
Do not power cycle the controller to perform a restart, i.e., changes may be lost by
shutting down the controller too soon.
Only restart the controller using the software reboot function. This ensures that all
memory operations are completed correctly and completely.
Pos : 49.5 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
112
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 49.6 /Serie 750 (WAGO-I/O-SYST EM)/Web-Bas ed-Management-System WBM/PFC xxxWBM PFC xxx Sei te "Status Infor mation" @ 14\mod_1362638885710_21.doc x @ 113870 @ 455 @ 1
7.8.1.3
“Status Information” Page
The following tables explain the parameters listed on this page:
7.8.1.3.1 “Controller Details” Group
This group displays the properties of the controller.
Table 45: WBM “Status Information” Page – “Controller Details” Group
Parameter
Product Description
Order Number
License Information
Firmware Revision
Explanation
Controller identification
Item number of the controller
Notification that the CODESYS runtime system is
available
Firmware status
7.8.1.3.2 “Network Details (Xn)” Group(s)
This group displays the network and interface properties of the controller.
If the switch is enabled, one group (“Network Details X1/X2”) is shown for both
connections.
If the switch is disabled, a separate group (“Network Details X1” / “Network
Details X2”) is shown for each connection.
Table 46: WBM “Status Information Page – “Network Details (Xn)” Group(s)
Parameter
State
Mac Address
IP Address
Subnet Mask
Explanation
Status of the ETHERNET interface
(enabled/disabled)
MAC address identifies and addresses the controller
Current IP address of the controller and (in brackets)
the reference type (static/bootp/dhcp)
Current subnet mask of the controller
Pos : 49.7 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
113
Pos : 49.8 /Serie 750 (WAGO-I/O-SYST EM)/Web-Bas ed-Management-System WBM/PFC xxxWBM PFC 200 Seite "Gener al PLC R unti me Configur ati on" , >= F W06, COD ESYS 2 und e!RUNTIME @ 23\mod_1441182132911_21.doc x @ 190628 @ 45 @ 1
7.8.1.4
“General PLC Runtime Configuration” Page
The settings for the boot project created with the programming software are given
on the “General PLC Runtime Configuration” page.
7.8.1.4.1 “General PLC Runtime Configuration” Group
Table 47: WBM “General PLC Runtime Configuration” Page – “General PLC Runtime
Configuration” Group
Display Fields
Explanation
Select here the PLC runtime system to be enabled.
No runtime system is enabled.
CODESYS 2 runtime system is
CODESYS 2
enabled.
e!RUNTIME runtime system is
e!RUNTIME
enabled.
Define if the home directory for the runtime system
should be moved to the memory card.
Home directory on memory
The home directory is stored in
Disabled
card enabled
the internal memory.
The home directory is moved to
Enabled
the memory card.
PLC runtime version
None
All data is deleted when switching the runtime system!
When the runtime system is changed, all data of the current runtime system is
deleted! This is the same as the runtime system function “Reset Original”.
Insert a memory card before switching the home directory!
When moving the home directory to the memory card, insert a memory card
formatted to support file system. Only the first partition of a memory card can be
accessed at /media/sd and can be used as the home directory.
Perform a reset before switching the home directory!
Stop IEC-61131 applications in use before switching the home directory of the
runtime system.
Restore the device to its initial state using the “Reset” function. Any boot project
is deleted.
Click [Submit] to apply the change.
The runtime system change is effective immediately.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
114
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
The home directory change only takes effect after restarting the controller. For
this purpose, use the WBM reboot function. Do not shut down the controller too
early!
Pos : 49.9 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
115
Pos : 49.10 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC 200 Sei te "PLC R untime Infor mation", >= F W04, COD ESYS 2, COD ESYS 2 und e!RUNTME @ 20\mod_1411560114644_21.doc x @ 164519 @ 4555 @ 1
7.8.1.5
“PLC Runtime Information” Page
All information about the enabled runtime system and PLC program created in the
programming software is provided on the “PLC Runtime Information” page.
7.8.1.5.1 “PLC Runtime” Group
Table 48: WBM “PLC Runtime Information” Page – “PLC Runtime” Group
Display Fields
Version
Web Server Version
State
Number of Tasks
Explanation
The version of the currently activated runtime
system is shown here.
If the runtime system is disabled, “None” is
displayed and the subsequent fields of this group are
disabled.
This shows the version number of the web server.
This field is only visible when CODESYS 2 is
enabled as the runtime system.
The PLC operating state is shown. This field is only
visible when CODESYS 2 is enabled as the runtime
system.
STOP
PLC program is not executed.
RUN
PLC program is executed.
The number of tasks in the PLC program is shown.
This field is only visible when CODESYS 2 is
enabled as the runtime system.
7.8.1.5.2 “Project Details” Group
This group is only visible if CODESYS 2 is enabled as the runtime system.
Table 49: WBM “PLC Runtime Information” Page – “Project Details” Group
Display Fields
Date
Title
Version
Author
Description
Explanation
Display of project information that the programmer
entered in the PLC program (in programming
software under Project > Project Information...).
The information only appears when a PLC program
is run.
Descriptive texts up to 1024 characters long are
given under “Description.”
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
116
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.1.5.3 “Task n” Group(s)
This group is only visible if CODESYS 2 is enabled as the runtime system.
One dedicated group is displayed for each task when the PLC program is
executed. As a rule, only the group title is displayed with the task number, the task
name and the task ID.
Click [+] to expand the group and display the following information.
Table 50: WBM “PLC Runtime Information” Page – “Task n” Group(s)
Display Field
Cycle count
Cycle time (µsec)
Cycle time min (µsec)
Cycle time max (µsec)
Cycle time avg (µsec)
Status
Mode
Priority
Interval (msec)
Explanation
Number of task cycles since the system start
Currently measured task cycle time for the task
Minimum task cycle time for the task since the
system start
Maximum task cycle time for the task since the
system start
Average task cycle time since the system start
Task status (e.g., RUN, STOP)
Task execution mode (e.g., in cycles)
Set task priority
Set task interval
To hide this information, click [–].
Pos : 49.11 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
117
Pos : 49.12 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC 200 Sei te "PLC WebVisu" , >= F W04, COD ESYS 2 und e!RUNTIME @ 20\mod_1411555423769_21.doc x @ 164463 @ 45 @ 1
7.8.1.6
“PLC WebVisu” Page
The settings for the web visualization created in the runtime system are shown on
the “PLC WebVisu” page.
7.8.1.6.1 “Web Server Configuration” Group
Table 51: WBM “PLC WebVisu” Page – “Web Server Configuration” Group
Display Fields
CODESYS 2 Webserver
State
e!RUNTIME Webserver
State
Default Webserver
Explanation
This indicates the status (enabled/disabled) of the
CODESYS 2 web server.
This indicates the status (enabled/disabled) of the
e!RUNTIME web server.
Choose here whether the Web-based Management or
web visualization of the runtime system should be
displayed when only entering the IP address of the
controller.
Web-based The Web-based Management is
Management displayed.
Web-Visu
The web visualization of the runtime
system is displayed.
Click [Submit] to apply change. The change is effective immediately.
In its default setting, the WBM is called up when only entering the IP address.
To update the display after switching, enter the IP address again in the address
line of the web browser.
To display the web visualization, the web server must be enabled (in WBM under
“Ports and Services” -> “PLC Runtime Services”) and there must be a suitably
configured application.
Regardless of the default web browser setting, the WBM can be called up at any
time with “http://<IP address>/wbm” and the web visualization with “http://<IP
address>/webvisu.”
You can obtain additional information on CODESYS 2 web visualization in the
section of the same name.
Possible error messages when calling up the web visualization
The “500 − Internal Server Error” message indicates that the web server is not
enabled.
A page with the header “WebVisu not available” means that no application has
been loaded in the controller using web visualization.
Pos : 49.13 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
118
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 49.14 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "C onfiguration of H ost and D omai n N ame", >= F W06 @ 22\mod_1429600097509_21.doc x @ 180745 @ 455 @ 1
7.8.1.7
“Configuration of Host and Domain Name” Page
The settings for the general TCP/IP parameters are found on the “Configuration of
Host and Domain Name” page.
7.8.1.7.1 “HostName” Group
Table 52: WBM “Configuration of Host and Domain Name” Page – “Hostname” Group
Parameters
Currently used
Configured
Explanation
If you have selected dynamic assignment of an IP
address via DHCP, the name of the host currently
being used is displayed.
Enter here the hostname of your controller to be used
if the network interface is changed to a static IP
address or if no hostname is transmitted with a
DHCP response.
Click [Submit] to apply the change. The change is effective immediately.
If a hostname is supplied via a DHCP response, this is enabled in the system. If
there are several network interfaces with DHCP always the last received hostname
is valid.
If only the hostname configured here is to be valid, the configuration of the DHCP
server must be adapted so that no hostnames are transferred in the DHCP
response.
7.8.1.7.2 “Domain Name” Group
Table 53: WBM “Configuration of Host and Domain Name” Page – “Domain Name” Group
Parameters
Currently used
Configured
Explanation
The domain name currently used is displayed.
It may differ from the configured domain name if
you have selected dynamic assignment of an IP
address via DHCP or BootP.
Enter the domain name.
The default entry is “localdomain.lan”.
Click [Submit] to apply the change. The change is effective immediately.
If a domain name is supplied via a DHCP response, this is enabled in the system.
If there are several network interfaces with DHCP, the last received domain name
is always valid.
If only the domain name configured here is to be valid, the configuration of the
DHCP server must be adapted so that no domain names are transferred in the
DHCP response.
Pos : 49.15 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
119
Pos : 49.16 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxx/WBM PFC xxx Sei te " TCP/IP Configur ati on", == F W06 @ 22\mod_1431932760259_21.doc x @ 182158 @ 4555 @ 1
</dg_
7.8.1.8
“TCP/IP Configuration” Page
The TCP/IP settings for the ETHERNET interfaces are shown on the “TCP/IP
configuration” page.
7.8.1.8.1 “IP Configuration (Xn)” Group(s)
If the switch is enabled, one group (“IP Configuration”) is shown for both
connections.
If the switch is disabled, a separate group (“IP Configuration X1” / “IP
Configuration X2”) is shown for each connection.
Table 54: WBM “TCP/IP Configuration” Page – “IP Configuration (Xn)” Group(s)
Parameters
Configuration Type
IP Address
Subnet Mask
Explanation
Select a static or dynamic IP address.
Static IP
Static IP addressing
DHCP
Dynamic IP addressing
BootP
Dynamic IP addressing
Enter here a static IP address. This is enabled if
“Static IP” is enabled in the Configuration Type
field.
Enter the subnet mask. This is enabled if “Static IP”
is enabled in the Configuration Type field.
Click [Submit] to apply changes. The changes are effective immediately.
7.8.1.8.2 “Default Gateway n” Groups
You can configure two default gateways. The controller transmits all network data
not going to a station on the local network to a default gateway. First the gateway
with the lowest metric is addressed. If this is not reached, the second gateway is
used. The selection is random if the metric is the same.
A default gateway can also be configured via DHCP. These default gateways are
given the metric 10, by which they are normally used before the static gateways.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
120
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 55: WBM “TCP/IP Configuration” Page – “Default Gateway n” Group
Parameters
Gateway enabled
Gateway Address
Gateway Metric
Explanation
Set here whether the selected default gateway is to
be used.
Disabled
The default gateway is not used.
Enabled
The default gateway is used.
Enter the address of the default gateway.
Set here a number as the metric. With multiple
default gateways, the metric defines the gateway to
which data packets are first sent. Priority is given to
the gateway with the lower metric. The default value
for the metric is 20.
The lowest value is 0.
The highest value is 4.294.967.295.
Click [Submit] to apply the change. The change is effective immediately.
7.8.1.8.3 “DNS Server” Group
Table 56: WBM “TCP/IP Configuration” Page – “DNS Server” Group
Parameters
Configured: None/
DNS Server n
New Server IP
Additionally used
(assigned by DHCP)
Explanation
The addresses of the defined DNS servers are
displayed. If no server has been defined,
“Configured: None” is displayed.
Add additional DNS addresses.
The DNS servers assigned if necessary by DHCP (or
BootP) are displayed. If no DNS server has been
assigned by DHCP (or BootP), “none” is displayed.
Click [Delete] to remove the selected DNS server. The change is effective
immediately.
Click [Add] to add the entered DNS server. The change is effective immediately.
Pos : 49.17 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
121
Pos : 49.18 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite " Ether net C onfigurati on" , >= F W04 @ 20\mod_1411548275226_21.doc x @ 164445 @ 455 @ 1
7.8.1.9
“Ethernet Configuration” Page
The settings for Ethernet TCP/IP are located on the “Ethernet Configuration”
page.
7.8.1.9.1 “Switch Configuration” Group
Table 57: WBM “Ethernet Configuration” Page – “Switch Configuration” Group
Parameter
Interfaces
Port Mirror
Fast Aging enabled
Broadcast Protection
Rate Limit
Explanation
Enable or disable the switch.
Both interfaces are operated with one
Switched
IP address.
Each interface is operated with its own
Separated
IP address.
Enable or disable the mirroring of the data traffic
between the ports.
None
Both Ethernet ports operating normally.
The entire data traffic between X1 and
X1
the PFC system is mirrored at port X2.
The entire data traffic between X2 and
X2
the PFC system is mirrored at port X1.
Set here the aging time of unused entries in the list of
MAC addresses with a port assignment to external
network stations.
An unused address entry becomes
Disabled
obsolete after 200 seconds.
An unused address entry becomes
Enabled
obsolete after 800 microseconds.
Set here the broadcast limit for protection against
overloads.
Disabled
No limitation of broadcast packets.
Limitation of incoming broadcast
packets to the selected percentage of
1 % ... 5 %
the total possible data throughput
(10/100Mbit).
Set here the basic limitation of the incoming data
traffic.
No limitation of the incoming data
Disabled
traffic
64 kbps … Limitation of the incoming data traffic
99 mbps
to the entered value
Click [Submit] to apply the change. The change is effective immediately.
7.8.1.9.2 “Interface Xn” Groups
One group (“Interface X1” / “Interface X2”) is displayed for each connection.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
122
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 58: WBM “Ethernet Configuration” Page – “Interface Xn” Groups
Parameter
Enabled
Autonegotiation on
Explanation
You can enable or disable the interface.
When Autonegotiation is enabled, the connection
modalities are negotiated automatically with the peer
devices.
Select the transmission speed and the duplex
method:
10 Mbit half-duplex
Speed/Duplex
100 Mbit half-duplex
10 Mbit full-duplex
100 Mbit full-duplex
Information can only be
sent or received.
Information can be sent and
received simultaneously.
Click [Submit] to apply changes. The changes are effective immediately.
Pos : 49.19 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
123
Pos : 49.20 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite " Gener al Firewall C onfiguration", == F W06 @ 22\mod_1432023378815_21.doc x @ 182242 @ 4555 @ 1
7.8.1.10
“General Firewall Configuration” Page
7.8.1.10.1 “Global Firewall Parameters” Group
Table 59: WBM “General Firewall Configuration” Page – “Global Firewall Parameters” Group
Parameters
Explanation
Enables/disables the complete functionality of the
firewall. This setting has the highest priority. If the
firewall is disabled, all other settings have no direct
Firewall enabled entirely
effect. The configuration of the other parameters is
possible nevertheless so that you can set the firewall
parameters correctly before you enable the firewall.
ICMP echo broadcast
Enable or disable the “ICMP echo broadcast”
protection
protection.
Max. UDP connections per You can specify the maximum number of UDP
second
connections per second.
Max. TCP connections per You can specify the maximum number of TCP
second
connections per second.
Click [Submit] to apply the change. The change is effective immediately.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
124
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.1.10.2 “Firewall Parameters Interface Xn” Group
These settings in this group refer to the configuration of the firewall at IP level.
Table 60: WBM “General Firewall Configuration” Page – “Firewall Parameter Interface Xn” Group
Parameters
Firewall enabled for
Interface
Explanation
Enable or disable the firewall for the specific
interface.
Enable or disable the “ICMP echo” protection for the
ICMP echo protection
respective interface.
You can specify the maximum number of “ICMP
ICMP echo limit per second
echo bursts” per second.
Telnet
FTP
FTPS
HTTP
HTTPS
Enable or disable the
I/O-CHECK
firewall for the respective
PLC Runtime
service.
PLC WebVisu –
The services themselves
Service enabled
direct link (port 8080)
must be enabled or disabled
SSH
separately on the “Ports and
TFTP
Services” page.
BootP/DHCP
DNS
MODBUS TCP
MODBUS UDP
SNMP
Click [Submit] to apply the change. The change is effective immediately.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
125
7.8.1.10.3 “Firewall Parameter Interface VPN” Group
These settings in this group refer to the configuration of the firewall at IP level.
Table 61: WBM “General Firewall Configuration” Page – “Firewall Parameter Interface VPN”
Group
Parameters
Firewall enabled for
Interface
Explanation
Enable or disable the firewall for the VPN interface.
Enable or disable the “ICMP echo” protection for the
VPN interface.
You can specify the maximum number of “ICMP
ICMP echo limit per second
echo bursts” per second.
Telnet
FTP
FTPS
HTTP
HTTPS
Enable or disable the
I/O-CHECK
firewall for the respective
PLC Runtime
service.
PLC WebVisu –
Service enabled
The services themselves
direct link (port 8080)
must be enabled or disabled
SSH
separately on the “Ports and
TFTP
Services” page.
BootP/DHCP
DNS
MODBUS TCP
MODBUS UDP
SNMP
ICMP echo protection
Click [Submit] to apply the change. The change is effective immediately.
Pos : 49.21 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
126
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 49.22 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "C onfiguration of M AC address filter", >= FW04 @ 20\mod_1411728806527_21.doc x @ 164958 @ 4555 @ 1
</dg_
7.8.1.11
“Configuration of MAC Address Filter” Page
You set the firewall configuration at ETHERNET level on this page.
The “MAC Address Filter Whitelist” contains a default entry with the following
values:
MAC address: 00:30:DE:00:00:00
MAC mask: ff:ff:ff:00:00:00
If you enable the default entry, this already allows communication between
different WAGO devices in the network.
Enable the MAC address filter before activation!
Before activating the MAC address filter, you must enter and activate your own
MAC address in the “MAC Address Filter Whitelist.”
Otherwise you cannot access the device via the ETHERNET. This also applies to
other services that are used by your device, e.g., the IP configuration via DHCP.
If the “MAC Address Filter Whitelist” does not contain the MAC address of your
DHCP server, your device will lose its IP settings after the next refresh cycle and
is then no longer accessible.
If the “MAC Address Filter Whitelist” does not contain an entry, the activation of
the filter is prevented.
If at least one activated address is entered, you will receive an appropriate
warning before activation, which you have to acknowledge.
The check described above is only performed in the WBM but not in the CBM!
7.8.1.11.1 “Global MAC Address Filter State” Group
Table 62: WBM “Configuration of MAC Address Filter” Page – “Global MAC Address Filter
State” Group
Parameters
Filter enabled
Explanation
Enable or disable the global MAC address filter here.
Click [Submit] to apply change. The change is effective immediately.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
127
7.8.1.11.2 “MAC Address Filter State Xn” Group
Table 63: WBM “Configuration of MAC Address Filter” Page – “MAC Address Filter State Xn”
Group
Parameters
Filter enabled
Explanation
Enable or disable here the MAC address filter for the
specific interface.
Click [Submit] to apply change. The change is effective immediately.
7.8.1.11.3 “MAC Address Filter Whitelist” Group
Table 64: WBM “Configuration of MAC Address Filter” Page – “MAC Address Filter Whitelist”
Group
Parameters
MAC address
MAC mask
Filter enabled
…
MAC address
MAC mask
Filter enabled
Explanation
Displays the MAC address of the relevant list entry.
This displays the MAC mask of the relevant list
entry.
Enable or disable the filter for the relevant list entry
here.
Enter here the MAC address for a new list entry.
You can enter 10 filters.
Enter the MAC mask for the new list entry here.
Enable or disable the filter for the new list entry
here.
Click [Submit] to apply the change. The change is effective immediately.
Click the appropriate [Delete] button to remove an existing list entry. The change
is effective immediately.
Click [Add] to accept a new list entry. You can enter 10 filters. The change is
effective immediately.
Pos : 49.23 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
128
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 49.24 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "C onfiguration of Us er Filter", == F W06 @ 22\mod_1432023377777_21.doc x @ 182238 @ 4555 @ 1
7.8.1.12
“Configuration of User Filter” Page
7.8.1.12.1 “User Filter” Group
Table 65: WBM “Configuration of User Filter” Page – “User Filter” Group
Parameters
Count
Explanation
The number of configured user filters is displayed.
7.8.1.12.2 “User Filter n” Group
Table 66: WBM “Configuration of User Filter” Page – “User Filter n” Group
Parameters
Source IP address
Source netmask
Source port
Destination IP address
Destination subnet mask
Destination port
Protocol
Input interface
Explanation
The source IP address for the respective filter entry
is displayed.
This displays the source network for the
corresponding filter entry.
The source port number for the respective filter entry
is displayed.
The destination IP address for the respective filter
entry is displayed.
The destination network mask for the respective
filter entry is displayed.
The designation port number for the respective filter
entry is displayed.
The permitted protocols for the respective filter is
displayed.
The permitted interfaces for the respective filter are
displayed.
Click the appropriate [Delete] button to remove a configured filter. The change is
effective immediately.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
129
7.8.1.12.3 “Add New User Filter” Group
You only have to enter values in the fields that are to be set for the filter. At least
one value must be entered, all other fields can remain empty.
Table 67: WBM “Configuration of User Filter” Page – “Add New User Filter” Group
Parameters
Source IP address
Source netmask
Source port
Destination IP address
Destination subnet mask
Destination port
Protocol
Input interface
Explanation
Enter here the source IP address for the new filter
entry.
Enter here the source network mask for the new filter
entry.
Enter here the source port address for the new filter
entry.
Enter here the destination IP address for the new
filter entry.
Enter here the destination network mask for the new
filter entry.
Enter the destination port number for the new filter
entry.
Enter here the permitted protocols for the new filter.
TCP
The TCP service is permitted.
UDP
The UDP service is permitted.
Enter here the permitted interfaces for the new filter.
X1
The X1 interface is permitted.
X2
The X2 interface is permitted.
VPN
The VPN interface is permitted.
To accept the new filter click [Add]. The change is effective immediately.
Pos : 49.25 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
130
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 49.26 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "C onfiguration of Ti me and D ate" @ 14\mod_1362643874444_21.doc x @ 113895 @ 45555 @ 1
</dg_
7.8.1.13
“Configuration of Time and Date” Page
The settings for date and time are shown on the “Configuration of Time and Date”
page.
7.8.1.13.1 “Date on Device” Group
Table 68: WBM “Configuration of Time and Date” Page – “Date on Device” Group
Parameter
Local
Explanation
Set date here.
Click [Change date] to apply change. The change is effective immediately.
7.8.1.13.2 “Time on Device” Group
Table 69: WBM “Configuration of Time and Date” Page – “Time on Device” Group
Parameter
Local
UTC
12 h format
Explanation
Set local time.
Set GMT time.
For switching between 12-hour and 24-hour time
display.
Click [Change time] to apply change to the time. The change is effective
immediately.
Click [Change format] to apply change to the time format. The change will be
effective at once.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
131
7.8.1.13.3 “Timezone” Group
Table 70: WBM “Configuration of Time and Date” Page – “Timezone” Group
Parameter
Time zone
Explanation
Specify the appropriate time zone for your location
here. Default setting:
AST/ADT
“Atlantic Standard Time,” Halifax
“Eastern Standard Time,” New York,
EST/EDT
Toronto
“Central Standard Time,” Chicago,
CST/CDT
Winnipeg
“Mountain Standard Time,” Denver,
MST/MDT
Edmonton
“Pacific Standard Time,” Los
PST/PDT
Angeles, Whitehouse:
Greenwich Mean Time,“ GB, P, IRL,
GMT/BST
IS, …
“Central European Time,” B, DK, D,
CET/CEST
F, I, CRO, NL, …
“East European Time,” BUL, FI, GR,
EET/EEST
TR, …
CST
“China Standard Time”
JST
“Japan/Korea Standard Time”
Click [Change] to apply time zone change. The change is effective immediately.
7.8.1.13.4 “TZ String” Group
Table 71: WBM “Configuration of Time and Date” Page – “TZ String” Group
Parameter
TZ String
Explanation
Enter the name of your time zone or country and
town if the time zone is not available for selection
using the “Timezone” parameter.
You can define a valid name for the time zone here:
http://www.timeanddate.com/time/map/
Click [Change] to apply the change. The change is effective immediately.
Pos : 49.27 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
132
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 49.28 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "C onfiguration of the us ers for the WBM" @ 14\mod_1362652743737_21.doc x @ 113930 @ 45 @ 1
</dg_
7.8.1.14
“Configuration of the Users for the Web-based Management” Page
The settings for user administration are shown on this page.
7.8.1.14.1 “Change Password for Selected User” Group
Change passwords
Default passwords are documented in these instructions and therefore do not offer
adequate protection! Change the passwords to meet your particular needs.
Table 72: WBM “Configuration of the users for the Web-based Management” Page – “Change
Password for Selected User” Group
Parameters
Select User
New Password
Confirm password
Explanation
Select the user (“user” or “admin”) for new
password assignment.
Enter the new password for the user selected under
“Select User”.
The following ASCII characters for passwords are
valid: a … z, A … Z, 0 … 9 and spaces. These
special characters are also valid:
]!"#$%&'()*+,./:;<=>?@[\^_`{|}~Enter the new password again for confirmation.
Click [Change Password] to apply change. The change is effective immediately.
Observe the valid characters for WBM passwords!
If WBM passwords with invalid characters are set outside the WBM system (e.g.
via CBM), then accessing the WBM pages is no longer possible!
Observe access rights
Authorized WBM users only have access to the Web pages. User administration
for controller applications is configured separately.
Pos : 49.29 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
133
Pos : 49.30 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "Cr eate bootable Image", >= FW06 @ 22\mod_1430312538493_21.doc x @ 181538 @ 45 @ 1
</dg_
7.8.1.15
“Create Bootable Image” Page
You can create a bootable image on the “Create Bootable Image” page.
7.8.1.15.1 "Create Bootable Image from Active Partition (<Active Partition>"
Group
The active partition that boot-up was performed from is displayed in brackets in
the heading.
Table 73: WBM “Create Bootable Image” page – “Create bootable image from active partition”
Group
Parameters
Destination
Size of created image
Explanation
The possible destination partition that an image will
be saved to is displayed. Depending on which
medium has been booted, the following destination
is available for selection after boot-up for the image
to be generated:
System was booted
Target partition for
from
“bootable image”
Memory Card
 Internal Flash
Internal memory
 Memory Card
Define the size of the image on the memory card.
This field is only visible when “Memory Card” is set
as the target.
Reduced to
The storage space of the copied
content
image is kept as small as possible.
The image is created so that the
Full card size
entire memory card is filled.
Once the destination has been determined and output, it is then checked and the
results of this check are displayed below the settings:
-
Free space on target device:
If the available memory space is less than 5% a warning is displayed. You
can still start the copy process despite the warning. If the available space is
definitively too low, a corresponding message is displayed and copying
cannot be started.
-
Device being used by CODESYS:
If the device is being used by CODESYS a warning is displayed. Although
it is not recommended, you can still start the copying procedure despite this
warning.
Click [Start Copy] to start the copying procedure. If the outcome of the test is
positive, copying begins immediately. If errors have been detected, a
corresponding message is displayed and copying is not started. If warnings have
been issued, these are displayed again and you must then confirm that you still
wish to continue.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
134
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Remove the memory card write protection!
Because write access to the memory card is possible during the boot process, the
memory card cannot be write protected when creating the image and during
operation.
Pos : 49.31 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
135
Pos : 49.32 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "C onfiguration of Seri al Interface RS232" @ 14\mod_1362652754225_21.doc x @ 113942 @ 455 @ 1
</dg_
7.8.1.16
“Configuration of Serial Interface RS232” Page
The settings for the serial interface are shown on the “Configuration of Serial
Interface RS232” page.
7.8.1.16.1 “Serial Interface Assigned to” Group
The application that the serial interface is currently assigned to is displayed.
7.8.1.16.2 “Assign Owner of Serial Interface (Active after Next Controller
Reboot)” Group
You can specify the application that the serial interface is assigned to after the
next controller reboot.
Table 74: WBM “Configuration of Serial Interface RS232” Page – “Assign Owner of Serial
Interface” Group
Parameters
Linux® Console
Unassigned (usage by
applications, libraries,
CODESYS)
Explanation
Specify that the serial interface is assigned to the
Linux® console.
Specify that the serial interface is not to be assigned
to any particular application and is available, so that
the CODESYS program, for example, can access it
via function blocks.
Remove RS-485 devices before switching to “Linux Console”!
Connected RS-485 devices can be damaged when switching to “Linux Console”.
Remove these devices before switching!
Click [Change Owner] to apply the change. The change only takes effect after
restarting the controller. For this purpose, use the WBM reboot function. Do not
shut down the controller too early!
Pos : 49.33 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
136
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 49.34 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "C onfiguration of Ser vic e Interfac e", >= FW06 @ 23\mod_1436427416342_21.doc x @ 185811 @ 455 @ 1
7.8.1.17
“Configuration of Service Interface” Page
The settings for the service interface are shown on the “Configuration of the
Service Interface” page.
7.8.1.17.1 “Service Interface assigned to” Group
The application that the service interface is currently assigned to is displayed.
7.8.1.17.2 “Assign Owner of Service Interface (enabled after next controller
reboot)” Group
You can specify the application to which the service interface is assigned after the
next controller reboot.
Table 75: WBM “Configuration of Serial Interface RS-232” page – “Assign Owner of Service
Interface” Group
Parameters
WAGO Service
Communication
Linux® Console
Unassigned (usage by
applications, libraries,
CODESYS)
Explanation
Specify that the service interface is used for the
WAGO Service communication or runtime system
communication.
Specify that the service interface is assigned to the
Linux® console.
Specify that the service interface is not to be
assigned to any application and is available, so that
the CODESYS program, for example, can access it
via function blocks.
Click [Change Owner] to apply the change. The changes only take effect after
restarting the controller. For this purpose, use the WBM reboot function. Do not
shut down the controller too early!
Pos : 49.35 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
Pos : 49.36 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "R eboot C ontroll er" @ 14\mod_1362652775280_21.doc x @ 113950 @ 45 @ 1
</dg_
7.8.1.18
“Reboot Controller” Page
The settings for the system reboot are shown on the “Reboot Controller” page.
7.8.1.18.1 “Reboot Controller” Group
Click the [Reboot] button to reboot the system.
Account for boot-up time!
The boot process takes time. You cannot access the controller while this is
occurring.
Pos : 49.37 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
137
138
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 49.38 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "Fir mwar e Bac kup" @ 14\mod_1362645403766_21.doc x @ 113914 @ 4 @ 1
</dg_
7.8.1.19
“Firmware Back-up” Page
The settings for a firmware backup are shown on the “Firmware Backup” page.
Select the packages to be restored in the Packages group. Select the
corresponding entries.
Only one package may be copied to the network!
If you have specified “Network” as the storage location, only one package may be
selected for each storing process.
In the selection box Destination, select the target storage location.
No backup of the memory card!
Backup from the memory card to the internal flash memory is not possible.
To activate the automatic update function mark check box Activate “auto update
feature”.
Account for backup time
Generation of backup files can take several minutes. Stop the CODESYS program
before you start the backup procedure to help shorten the time required.
To begin the backup procedure, click the [Submit] button.
Pos : 49.39 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
139
Pos : 49.40 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "Fir mwar e R estore" @ 14\mod_1362645409578_21.doc x @ 113918 @ 4 @ 1
7.8.1.20
“Firmware Restore” Page
The settings for restoring the firmware are shown on the “Firmware Restore”
page.
Restoration only possible from internal memory!
If the device was booted from the memory card, the firmware cannot be restored.
Reset by restore
A reset is performed when the system or settings are restored by CODESYS!
Connection loss through restore
If the restore changes the parameters of the ETHERNET connection, the WBM
may then no longer be able to open a connection to the device. You must call the
WBM again by entering the correct IP address of the device in the address line.
In the Source selection box, select the storage location.
Select the packages to be restored in the Packages group. To do this, select the
corresponding entries.
In the CODESYS backup file input field, enter the name of the backup file for
the CODESYS project or click the [Browse] button to select the file in Explorer.
In the Settings backup file input field, enter the name of the backup file for the
settings or click the [Browse] button to select the file in Explorer.
In the System backup file input field, enter the name of the backup file for the
system data or click the [Browse] button to select the file in Explorer.
To start the restore procedure, click the [Submit] button.
Pos : 49.41 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
140
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 49.42 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite " System Parti tion" @ 14\mod_1362652756710_21.doc x @ 113946 @ 455 @ 1
</dg_
7.8.1.21
“System Partition” Page
The settings for specifying the partition that the system will be started from are
shown on the “System Partition” page.
7.8.1.21.1 “Current Active Partition” Group
The partition currently in use is displayed here.
7.8.1.21.2 “Set Inactive Partition Active” Group
Click [Activate Partition] to start the system from a different partition at the next
controller reboot.
Ensure bootable partition!
A functional firmware backup must be present in the boot partition!
Pos : 49.43 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
141
Pos : 49.44 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "M ass Storag e" @ 14\mod_1362644664178_21.doc x @ 113902 @ 455 @ 1
</dg_
7.8.1.22
“Mass Storage” Page
A group containing information about the storage volume is displayed for each
storage volume that is found, along with an additional group for formatting (when
this is possible).
The group title contains the designation for the storage volume (“SD card” or
“Internal Flash”) and, if this storage volume is also the active partition, the text
“Active Partition”.
7.8.1.22.1 “<Device Name>” Group(s)
Table 76: WBM “Mass Storage” Page – “<Device Name>” Group
Parameters
Device
Volume name
Explanation
The name of the storage volume in the operating
system file system is displayed here.
The name of the storage volume is displayed here.
7.8.1.22.2 “<Device Name> - FAT Format” Group(s)
Table 77: WBM “Mass Storage” Page – “<Device Name>” Group
Parameters
Volume Name
Explanation
Specify the name for the storage volume when
formatted.
Data are deleted!
Any data stored in the storage volume is deleted during formatting!
To format the specified storage volume, click [Start Formatting].
Pos : 49.45 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
142
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 49.46 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite " Software U ploads", >= FW04, <= FW06 @ 21\mod_1417776195715_21.doc x @ 170082 @ 455 @ 1
</dg_
7.8.1.23
“Software Uploads” Page
The settings for a device update are shown on the “Software Uploads” page.
7.8.1.23.1 “Upload New Software” Group
Table 78: WBM “Software Uploads” Page – “Upload New Software” Group
Parameter
Software Files
Explanation
You can select fieldbus software, program licenses
and update scripts, for example, for transfer from a
PC to the controller.
To select a file on the PC, click the [Browse] button.
To transfer the selected file to the controller, click [Start Upload] button.
7.8.1.23.2 “Activate New Software” Group
Table 79: WBM “Software Uploads” Page – “Activate New Software” Group
Parameter
Software File
Action
Explanation
This shows the file name of the transferred software
package. If no new uploaded software package is
present on the controller, the message “No upload
file exists” is displayed.
Select here the action required.
Activate The transferred software package is
activated.
Discard
The transferred software package is
(delete
deleted again by the controller.
upload)
To perform the action, click the [Submit] button. The process starts immediately.
The file with the software package is deleted again after the installation is
completed or when the controller is restarted.
Pos : 49.47 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
143
Pos : 49.48 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "C onfiguration of N etwor k Ser vic es", >= F W04 @ 20\mod_1411541924837_21.doc x @ 164325 @ 4555555 @ 1
</dg_
7.8.1.24
“Configuration of Network Services” Page
The settings for various services are shown on the “Configuration of Network
Services” page.
Besides enabling/disabling the individual services, you can limit the services for
each particular interface also via the firewall on the “General Firewall
Configuration” page.
7.8.1.24.1 “Telnet” Group
Table 80: WBM “Configuration of Network Services” Page – “Telnet” Group
Parameters
Service active
Explanation
Enable/disable the Telnet service here.
Click the [Submit] button to apply the changes. The change is effective
immediately.
7.8.1.24.2 “FTP” Group
Table 81: WBM “Configuration of Network Services” Page – “FTP” Group
Parameters
Service active
Explanation
Enable/disable the FTP service here.
Click the [Submit] button to apply the changes. The change is effective
immediately.
7.8.1.24.3 “FTPS” Group
Table 82: WBM “Configuration of Network Services” Page – “FTPS” Group
Parameters
Service active
Explanation
Enable/disable the FTPS service here.
Click the [Submit] button to apply the changes. The change is effective
immediately.
7.8.1.24.4 “HTTP” Group
Table 83: WBM “Configuration of Network Services” Page – “HTTP” Group
Parameters
Service active
Explanation
Enable/disable the HTTP service here.
Click the [Submit] button to apply the changes. The change is effective
immediately.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
144
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Disconnection abort on disabling
If the HTTP service is disabled, the connection to the controller can be closed.
Then call up the WBM page again.
7.8.1.24.5 “HTTPS” Group
Table 84: WBM “Configuration of Network Services” Page – “HTTPS” Group
Parameters
Service active
Explanation
Enable/disable the HTTPS service here.
Click the [Submit] button to apply the changes. The change is effective
immediately.
Disconnection abort on disabling
If the HTTPS service is disabled, the connection to the controller can be closed.
Then call up the WBM page again.
7.8.1.24.6 “I/O-CHECK” Group
Table 85: WBM “Configuration of Network Services” Page – “I/O-CHECK” Group
Parameters
Service active
Explanation
Enable/disable the WAGO-I/O CHECK service here.
Click the [Submit] button to apply the changes. The change is effective
immediately.
Pos : 49.49 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
145
Pos : 49.50 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "C onfiguration of NT P Cli ent", >= F W06 @ 22\mod_1431933207488_21.doc x @ 182162 @ 455 @ 1
</dg_
7.8.1.25
“Configuration of NTP Client” Page
The settings for the NTP service are shown on the “Configuration of NTP Client”
page.
7.8.1.25.1 “NTP Client Configuration” Group
Table 86: WBM “Configuration of NTP Client” Page – “NTP Client Configuration” Group
Parameters
Service enabled
Service Result
Time Server n
Update interval (sec)
Additionally used
(assigned by DHCP)
Explanation
Enable/disabled time update.
This displays whether time data was accessible and
updated via NTP.
This field is only displayed with the NTP service
enabled.
Time server not
The time data was not yet
available until now
updated.
Time server available The time data was updated.
Enter here the IP addresses of up to 4 time servers.
Time server No. 1 is requested first of all. If no data
is accessible via this server, time server No. 2 is
requested etc.
Specify here the update interval of the time server.
The NTP servers assigned if necessary by DHCP (or
BootP) are displayed. If no NTP server has been
assigned by DHCP (or BootP), “none” is displayed.
Click the [Submit] button to apply the changes. The changes are effective
immediately.
7.8.1.25.2 “NTP Single Request” Group
To update the time immediately, irrespective of the update interval, click [Update
Time Now].
Pos : 49.51 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
146
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 49.52 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC 200 Sei te "Configur ation of PLC R unti me Ser vices" , >= F W04, CODESYS 2 und e!RUNTIME @ 20\mod_1411560115527_21.doc x @ 164523 @ 4555 @ 1
7.8.1.26
“Configuration of PLC Runtime Services” Page
The settings for various services of the activated runtime system are shown on the
“Configuration of PLC Runtime Services” page.
7.8.1.26.1 “General Configuration” Group
Table 87: WBM “Configuration of PLC Runtime Services” Page – “General Configuration” Group
Parameter
Port Authentication
Password
Confirm Password
Explanation
Specify the new password for port authentication.
Enter the new password again for confirmation.
Click [Submit] to apply change. The change is effective immediately.
7.8.1.26.2 “CODESYS 2” Group
Table 88: WBM “Configuration of CODESYS Services” Page – “CODESYS 2 Web Server” Group
Parameter
Explanation
This displays the status (enabled/disabled) of the
CODESYS 2 State
CODESYS 2 runtime system.
Enable or disable the CODESYS 2 web server for
Web server enabled
the CODESYS web visualization here.
Enable or disable the communication between the
Communication enabled
CODESYS 2 runtime system and the CODESYS 2
programming system.
Enter here the port number for communication with
Communication Port
the CODESYS 2 programming system. Default
Number
value is 2455.
Define here whether port authentication is enabled.
If this is enabled, the password specified under
Port authentication enabled
“General Configuration” must be entered when
logging in via CODESYS 2 IDE.
Click [Submit] to apply change. The change is effective immediately.
7.8.1.26.3 “e!RUNTIME” Group
Table 89: WBM “Configuration of CODESYS Services” Page – “e!RUNTIME Web Server” Group
Parameter
Explanation
This displays the status of the e!RUNTIME system
e!RUNTIME State
(enabled/disabled).
Enable or disable the e!WEBSERVER for the
Web server enabled
e!RUNTIME web visualization here.
Enter here whether a login is required for connecting
Port authentication enabled to the device. The user name is admin and the
password specified at “General Configuration.”
Click [Submit] to apply change. The change is effective immediately.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
147
Pos : 49.53 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Pos : 49.54 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite " SSH Ser ver Setti ngs", >= F W04 @ 20\mod_1411559427840_21.doc x @ 164507 @ 45 @ 1
7.8.1.27
“SSH Server Settings” Page
The settings for the SSH service are shown on the “SSH Server Settings” page.
7.8.1.27.1 “SSH Server” Group
Table 90: WBM “SSH Server Settings” Page – “SSH Server” Group
Parameter
Service active
Port Number
Allow root login
Allow password login
Explanation
You can enable/disable the SSH server here.
Specify the port number here.
You can enable or inhibit root access.
Activate or deactivate the password query function
here.
Click on [Submit] to accept the changes. The changes will be effective
immediately.
Pos : 49.55 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
148
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 49.56 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "TFT P Ser ver", >= FW04 @ 20\mod_1411559483204_21.doc x @ 164515 @ 45 @ 1
</dg_
7.8.1.28
“TFTP Server” Page
The settings for the TFTP service are shown on the “TFTP Server” page.
7.8.1.28.1 “TFTP Server” Group
Table 91: WBM “TFTP Server” Page – “TFTP Server” Group
Parameter
Service active
Download directory
Explanation
Activate or deactivate the TFTP server.
Specify here the path for downloading the server
directory.
Click on [Submit] to accept the changes. The changes will be effective
immediately.
Pos : 49.57 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
149
Pos : 49.58 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "DHC P C onfigurati on", >= F W04 @ 20\mod_1407147028450_21.doc x @ 161048 @ 45 @ 1
7.8.1.29
“DHCP Configuration” Page
The settings for the DHCP service are shown on the “DHCP Configuration” page.
7.8.1.29.1 “DHCP Configuration Xn” Group
Table 92: WBM “DHCP Configuration” – “DHCP Configuration Xn” Group
Parameter
Service active
IP Range
Lease time (sec)
Static hosts/
Static host n
New static host
Explanation
Enable or disable the DHCP service for the interface
Xn.
Enter here a range of available IP addresses.
Specify the lease time here in seconds. 120 seconds
are entered by default.
This displays the static assignments of MAC IDs to
IP addresses. If no assignment was defined, “No
static hosts configured” is displayed.
Enter here a new static assignment, e.g.,
“01:02:03:04:05:06=192.168.1.20” or
“hostname=192.168.1.20.”
You can enter 10 assignments.
Click on [Submit] to accept the changes. The changes will be effective
immediately.
Click on [Add] to accept a new assignment. The change is effective immediately.
Click on [Delete] to delete an existing assignment. The change is effective
immediately.
Pos : 49.59 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
150
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 49.60 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "C onfiguration of DN S Ser vic e", >= F W04 @ 20\mod_1407147036106_21.doc x @ 161052 @ 45 @ 1
7.8.1.30
“Configuration of DNS Service” Page
The settings for the DNS service are shown on the “Configuration of DNS
Service” page.
7.8.1.30.1 “DNS Service” Group
Table 93: WBM “Configuration of DNS Service” Page – “DNS Service” Group
Parameter
Service active
Mode
Static hosts
New static host
Explanation
You can enable/disable the DNS server service here.
Select here the operating mode of the DNS server:
Requests are buffered to optimize
Proxy
throughput.
Relay All requests are routed directly.
This displays the static assignments of IP addresses
to names. If no assignment was defined, “No static
hosts configured” is displayed.
Enter here a new static assignment, e.g.,
“192.168.1.20:hostname.”
You can enter 10 assignments.
Click on [Submit] to accept the changes. The changes will be effective
immediately.
Click on [Add] to accept a new assignment. The change is effective immediately.
Click on [Delete] to delete an existing assignment. The change is effective
immediately.
Pos : 49.61 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
151
Pos : 49.62 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "M ODBU S Ser vic es C onfiguration", >= FW04 @ 20\mod_1411723151031_21.doc x @ 164928 @ 455 @ 1
7.8.1.31
“MODBUS Services Configuration” Page
The settings for various MODBUS services are shown on the “MODBUS
Services Configuration” page. The groups are only visible if the e!RUNTIME
system is enabled. Otherwise an information text is displayed.
7.8.1.31.1 “MODBUS TCP” Group
Table 94: WBM “MODBUS Services Configuration” Page – “MODBUS TCP” Group
Parameter
Service active
Explanation
Disable or enable the MODBUS/TCP service here.
Click the [Submit] button to apply the changes. The change is effective
immediately.
7.8.1.31.2 “MODBUS UDP” Group
Table 95: WBM “MODBUS Configuration Services” Page – “MODBUS UDP” Group
Parameter
Service active
Explanation
Disable/enable the MODBUS-UDP service here.
Click the [Submit] button to apply the changes. The change is effective
immediately.
Pos : 49.63 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
152
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 49.64 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "C onfiguration of g eneral SNMP parameters", >= F W04 @ 20\mod_1411541926270_21.doc x @ 164399 @ 45 @ 1
7.8.1.32
“Configuration of General SNMP Parameters” Page
The general settings for SNMP are given on the “Configuration of General SNMP
Parameters” page.
7.8.1.32.1 “General SNMP Configuration” Group
Table 96: WBM “Configuration of General SNMP Parameters” Page – “General SNMP
Configuration” Group
Parameter
Service active
Name of device
Description
Physical location
Contact
Explanation
Activate/deactivate the SNMP service.
Enter here the device name (sysName).
Enter here the device description (sysDescription).
Enter here the location of the device (sysLocation).
Enter here the email contact address (sysContact).
Click the [Submit] button to apply the changes. The changes only take effect after
restarting the controller. For this purpose, use the WBM reboot function. Do not
shut down the controller too early!
Pos : 49.65 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
153
Pos : 49.66 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "C onfiguration of SNMP v1/v2c par ameters", >= F W04 @ 20\mod_1411541926803_21.doc x @ 164403 @ 45555 @ 1
7.8.1.33
“Configuration of SNMP v1/v2c Parameters” Page
The general settings for SNMP v1/v2c are shown on the “Configuration of SNMP
v1/v2c Parameters” page.
7.8.1.33.1 “SNMP v1/v2c Manager Configuration” Group
Table 97: WBM “Configuration of SNMP v1/v2c Parameters” Page – “SNMP v1/v2c Manager
Configuration” Group
Parameter
Protocol enabled
Local Community Name
Explanation
It is displayed the SNMP protocol for v1/v2c is
activated. The local community name is deleted
when the protocol is deactivated.
Specify here the community name for the SNMP
manager configuration. The community name can
establish relationships between SNMP managers and
agents who are respectively referred to as
“Community” and who control identification and
access between SNMP participants.
The community name can be up to 32 characters
long and must not include spaces.
To use the SNMP protocol, a valid community name
must always be specified. The default community
name is “public.”
Click [Change] to apply changes. The changes only take effect after restarting the
controller. For this purpose, use the WBM reboot function. Do not shut down the
controller too early!
7.8.1.33.2 “Actually Configured Trap Receivers” Group(s)
Table 98: WBM “Configuration of SNMP v1/v2c Parameters” Page – “Actually Configured Trap
Receivers” Group
Parameter
Count
Explanation
This displays number of configured trap receivers.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
154
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.1.33.3 “Trap Receiver n” Group(s)
A dedicated group with the following information is displayed for each trap
receiver:
Table 99: WBM “Configuration of SNMP v1/v2c Parameters” Page – “Trap Receiver n” Group(s)
Parameter
IP Address
Community Name
Version
Explanation
The IP address for the trap receiver (management
station) is displayed here.
This displays the community name for the trap
receiver configuration. The community name can be
evaluated by the trap receiver.
This displays the SNMP version, via which the traps
are sent: v1 or v2c (traps higher than v3 are
displayed in a separate form).
Click [Delete] to delete the trap receiver. The changes only take effect after
restarting the controller. For this purpose, use the WBM reboot function. Do not
shut down the controller too early!
7.8.1.33.4 “Add New Trap Receiver” Group
You can enter 10 trap receivers.
Table 100: WBM “Configuration of SNMP v1/v2c Parameters” Page – “Add New Trap Receiver”
Group
Parameter
IP Address
Community Name
Version
Explanation
Specify the IP address for the new trap receiver
(management station) here.
Specify here the community name for the new trap
receiver configuration. The community name can be
evaluated by the trap receiver.
The community name can be up to 32 characters
long and must not include spaces.
Specify the SNMP version that will send the traps:
v1 or v2c (traps higher than v3 are configured in a
separate form).
Click [Add] to add a new trap receiver. The changes only take effect after
restarting the controller. For this purpose, use the WBM reboot function. Do not
shut down the controller too early!
Pos : 49.67 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
155
Pos : 49.68 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "C onfiguration of SNMP v3 Us ers" @ 14\mod_1363614120310_21.doc x @ 114731 @ 4555 @ 1
</dg_
7.8.1.34
“Configuration of SNMP v3 Users” Page
The general settings for SNMP v3 are shown on the “Configuration of SNMP v3
Users” page.
7.8.1.34.1 “Actually Configured v3 Users” Group(s)
Table 101: WBM “Configuration of SNMP v3” Page – “Actually Configured v3 Users” Group
Parameters
Count
Explanation
The number of configured v3 users is displayed.
7.8.1.34.2 “v3 User n” Group(s)
A group with the following information is displayed for each user:
Table 102: WBM “Configuration of SNMP v3 Users” Page – “v3 User n” Group(s)
Parameters
Security Authentication
Name
Explanation
Authentication Type
Possible values:
- Use no authentication (“None”)
- Message Digest 5 (“MD5”)
- Secure Hash Algorithm (“SHA”)
Authentication Key (min.
eight char.)
Privacy
Privacy Key (min. eight
char.)
Notification Receiver IP
The user name is displayed.
The authentication type for the SNMP v3 packets is
displayed here.
The authentication key is displayed.
The encryption algorithm for the SNMP message is
displayed here.
Possible values:
- No encryption (“None”)
- Data Encryption Standard (“DES”)
- Advanced Encryption Standard (“AES”)
The key for encryption of the SNMP message is
displayed here. If nothing is displayed here, the
“authentication key” is automatically used.
The IP address of a trap receiver for v3 traps is
displayed here. If no v3 traps are to be sent for this
user, this field remains blank.
Click [Delete] to delete the user. The changes only take effect after restarting the
controller. For this purpose, use the WBM reboot function. Do not shut down the
controller too early!
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
156
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.1.34.3 “Add New v3 User” Group
You can enter 10 users.
Table 103: WBM “Configuration of SNMP v3 Users” Page – “Add New v3 User” Group
Parameters
Security Authentication
Name
Authentication Type
Authentication Key (min.
eight char.)
Privacy
Privacy Key (min. eight
char.)
Notification Receiver IP
Explanation
Enter the user name here. This name must be unique;
a pre-existing user name is not accepted when
entered here. The security authentication name can
have a maximum 32 characters, without any spaces.
Specify the authentication type for the SNMP v3
packets.
Possible values:
- Use no authentication (“None”)
- Message Digest 5 (“MD5”)
- Secure Hash Algorithm (“SHA”)
Specify the authentication key here. This
authentication key must have between eight and 32
characters, without any spaces.
Specify the encryption algorithm for the SNMP
message here.
Possible values:
- No encryption (“None”)
- Data Encryption Standard (“DES”)
- Advanced Encryption Standard (“AES”)
Enter the key for encryption of the SNMP message
here. If nothing is specified here, the “authentication
key” is automatically used. The privacy key must
have between eight and 32 characters, without any
spaces.
Specify an IP address for a trap receiver for v3 traps
here. If no v3 traps are to be sent for this user, this
field remains blank.
Click [Add] to add a new user. The changes only take effect after restarting the
controller. For this purpose, use the WBM reboot function. Do not shut down the
controller too early!
Pos : 49.69 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
157
Pos : 49.70 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "Di agnostic Infor mation", >= F W04 @ 21\mod_1417506028451_21.doc x @ 169768 @ 4 @ 1
</dg_
7.8.1.35
“Diagnostic Information” Page
The settings for displaying diagnostic messages are shown on the “Diagnostic
Information” page.
Table 104: WBM “Diagnostic Information” Page
Parameter
Read all notifications
Read only the last n
Automatic refresh cycle
(sec)
Explanation
Activate display of all messages.
Activate display of only the last n messages. You
also specify the number of messages to be displayed.
Select the check box to enable cyclic refresh.
Enter the cycle time in seconds in which a cyclic
refresh is performed. The label of the button
(“Refresh”/“Start“/“Stop”) changes depending on
status.
To refresh the display or to enable cyclic refresh, click the [Refresh] button. This
button is only visible if the cyclic refresh is not enabled or stopped.
To enable cyclic refresh, click the [Start] button. The button is only visible if
cyclic refresh is enabled and has not yet started.
To stop cyclic refresh again, click the [Stop] button. The button is only visible if
cyclic refresh is enabled.
The cyclical update is performed for as long as the “Diagnostic” page is opened.
If you change the WBM page, the update is stopped until you call up the
“Diagnostic” Page again.
The messages are displayed below the settings.
Pos : 49.71 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
158
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 49.72 /Serie 750 ( WAGO-I/O-SYST EM)/Web-Bas ed-M anagement-Sys tem WBM/PFC xxxWBM PFC xxx Seite "C onfiguration of OpenVPN and IPs ec", >= F W06 @ 23\mod_1436766288661_21.doc x @ 186038 @ 455555 @ 1
7.8.1.36
“Configuration of OpenVPN and IPsec” Page
The general settings for SNMP v1/v2c are shown on the “Configuration of SNMP
v1/v2c Parameters” page.
7.8.1.36.1 “OpenVPN” Group
Table 105: WBM “Configuration of OpenVPN and IPsec” Page – “OpenVPN” Group
Parameters
Current State
OpenVPN enabled
openvpn.config
Explanation
The current status of the OpenVPN service is
displayed.
stopped
The service is disabled.
running
The service is enabled.
Enable or disable the OpenVPN service.
Select an OpenVPN configuration file to be
transferred from PC to controller or vice versa.
To apply a status change, click the [Submit] button.
To select a file on the controller or PC, click the [Browse] button.
To transfer the selected file from the PC to the controller, click [Start Upload]
button.
To transfer the selected file from the controller to the PC, click [Start Download]
button.
The changes only take effect after restarting the controller. For this purpose, use
the WBM reboot function. Do not shut down the controller too early!
7.8.1.36.2 “IPsec” Group
Table 106: WBM “Configuration of OpenVPN and IPsec” Page – “IPsec” Group
Parameters
Current State
IPsec enabled
ipsec.config
ipsec.secrets
Explanation
The current status of the IPsec service is displayed.
stopped
The service is disabled.
running
The service is enabled.
Enable or disable the IPsec service.
Select an IPsec configuration file to be transferred
from PC to controller or vice versa.
Select an IPsec configuration file to be transferred
from PC to controller.
To apply a status change, click the [Submit] button.
To select a file on the controller or PC, click the [Browse] button.
To transfer the selected file to the controller, click [Start Upload] button.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
159
To transfer the selected file from the controller to the PC, click [Start Download]
button.
The changes only take effect after restarting the controller. For this purpose, use
the WBM reboot function. Do not shut down the controller too early!
7.8.1.36.3 “Certificate Upload” Group
Table 107: WBM “Configuration of OpenVPN and IPsec” Page – “Certificate Upload” Group
Parameters
New Certificate
New Private Key
Explanation
Select an certificate for transfer from a PC to the
controller.
Select a key for transfer from a PC to the controller.
To select a file on the PC, click the [Browse] button.
To transfer the selected file to the controller, click [Start Upload] button. The
changes will be effective immediately.
The certificates are saved in the directory “/etc/certificates/” and the keys in the
directory “/etc/certificates/keys/”.
7.8.1.36.4 “Certificate List” Group
Table 108: WBM “Configuration of OpenVPN and IPsec” Page – “Certificate List” Group
Parameters
<certificate name>
Explanation
The loaded certificates are displayed. If no certificate
has been loaded. “No certificates existing” is
displayed.
Click [Delete] to delete an entry. The changes will be effective immediately.
7.8.1.36.5 “Private Key List” Group
Table 109: WBM “Configuration of OpenVPN and IPsec” Page – “Private Key List” Group
Parameters
<key name>
Explanation
The loaded keys are displayed. If no keys has been
loaded. “No keys existing” is displayed.
Click [Delete] to delete an entry. The changes will be effective immediately.
Pos : 50 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
160
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 51 /Serie 750 ( WAGO-I/O-SYST EM)/In Betrieb nehmen/Konfigurieren 750- 8xxx mi t T ermi nal programm mit R S-232 (CBM) @ 14\mod_1361451964944_21.doc x @ 112618 @ 3 @ 1
7.8.2
Configuration using a Terminal Program (CBM)
You can use the Console-Based Management Tool (CBM) to configure the
controller via the ETHERNET interface and SSH, as well as the RS-232 interface
and Linux® console.
To establish a connection via the serial interface, set the baud rate to 115200 baud
in the terminal program. The settings for data bits, stop bits and parity do not need
to be adjusted.
To launch the CBM, log in to the Linux® console and enter the command "cbm"
(case sensitive).
Figure 46: CBM main menu (example)
Pos : 52.1 /Serie 750 (WAGO-I/O-SYST EM)/C ons ol e-Based-Management- System C BM/PFC xxx/CBM PFC xxx Ü bersic ht M enüs truktur, mit R S-232, ohne PR OFIBUS @ 24\mod_1448368417783_21.doc x @ 196102 @ 4 @ 1
7.8.2.1
CBM Menu Structure Overview
Table 110: CBM Menu Structure
Menu Hierarchy
0. Quit
1. Information
0. Back to Main Menu
1. Controller Details
2. Network Details
2. PLC Runtime
0. Back to Main Menu
1. Information
2. General Configuration
3. WebVisu
3. Networking
0. Back to Main Menu
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 110: CBM Menu Structure
Menu Hierarchy
1. Host-/Domain Name
2. TCP/IP
0. Back to Networking Menu
1. IP Address
2. Default Gateway
3. DNS Server
3. Ethernet
0. Back to Networking Menu
1. Switch Configuration
2. Ethernet Ports
0. Back to Ethernet Menu
1. Interface X1
2. Interface X2
4. Firewall
0. Back to Main Menu
1. General Configuration
2. MAC Address Filter
3. User Filter
5. Clock
0. Back to Main Menu
1. Date on device (local)
2. Time on device (local)
3. Time on device (UTC)
4. Clock Display Mode
5. Timezone
6. TZ-String
6. Administration
0. Back to Main Menu
1. Users
2. Create Image
3. Owner of Serial Interface
4. Reboot Controller
7. Package Server
0. Back to Main Menu
1. Firmware Backup
2. Firmware Restore
3. System Partition
8. Mass Storage
0. Back to Main Menu
1. Internal Flash (active partition)
9. Software Uploads
0. Back to Main Menu
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Commissioning
161
162
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 110: CBM Menu Structure
Menu Hierarchy
1. Update Script
10. Ports and Services
0. Back to Main Menu
1. Telnet
2. FTP
3. FTPS
4. HTTP
5. HTTPS
6. NTP
7. SSH
8. TFTP
9. DHCPD
10. DNS
11. IOCHECK PORT
12. Modbus TCP
13. Modbus UDP
14. PLC Runtime Services
11. SNMP
0. Back to Main Menu
1. General SNMP Configuration
2. SNMP v1/v2c Manager Configuration
3. SNMP v1/v2c Trap Receiver Configuration
4. SNMP v3 Configuration
5. SNMP firewalling
6. Secure SNMP firewalling
Pos : 52.2 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
163
Pos : 52.3 /Serie 750 (WAGO-I/O-SYST EM)/C ons ol e-Based-Management- System C BM/PFC xxx/CBM PFC xxx M enü "Infor mation" @ 24\mod_1445415237270_21.doc x @ 194044 @ 455 @ 1
7.8.2.2
“Information” Menu
This menu contains other submenus with information on the controller and
network.
Table 111: “Information” Menu
Menu Item
0. Back to …
1. Controller Details
2. Network Details
Explanation
Back to the higher-level menu
Opens a submenu with controller properties
Opens a submenu with controller network and
interface properties
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
7.8.2.2.1 “Information” > “Controller Details” Submenu
In this submenu, the controller properties are displayed.
Table 112: “Information” > “Controller Details” Submenu
Parameters
Product Description
Order Number
License Information
Firmware Revision
Explanation
Controller identification
Item number of the controller
Notification that the CODESYS runtime system is
available
Firmware status
To return to the higher-level menu, press [Q] or [Return].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
164
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.2.2.2 “Information” > “Network Details” Submenu
In this submenu, the network and interface properties of the controller are
displayed.
If the EHERNET interfaces are operated in “Switched” mode, a common table
(“X1/X2”) is displayed for both connections.
If the EHERNET interfaces are operated in “Separated” mode, an individual table
(“X1” / “X2”) is displayed for each connection.
Table 113: “Information” > “Network Details” Submenu
Parameters
State
Mac Address
IP Address
Subnet Mask
Explanation
Status of the ETHERNET interface
(enabled/disabled)
MAC address identifies and addresses the controller
Current IP address of the controller and (in brackets)
the reference type (static/bootp/dhcp)
Current subnet mask of the controller
To return to the higher-level menu, press [Q] or [Return].
Pos : 52.4 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
165
Pos : 52.5 /Serie 750 (WAGO-I/O-SYST EM)/C ons ol e-Based-Management- System C BM/PFC xxx/CBM PFC xxx M enü " PLC Runti me", C ODESYS 2 und e!RUNTIME @ 24\mod_1447401468691_21.doc x @ 195551 @ 4555555555555 @ 1
7.8.2.3
“PLC Runtime” Menu
This menu contains other submenus with information and settings for the runtime
system.
Table 114: “PLC Runtime” Menu
Menu Item
0. Back to …
1. Information
2. General Configuration
3. WebVisu
Explanation
Back to the higher-level menu
Opens a submenu with information on the runtime
system
Opens a submenu with settings for the runtime
system
Opens a submenu with settings for the Web
visualization
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
7.8.2.3.1 “PLC Runtime” > “Information” Submenu
This submenu contains other submenus with information on the runtime system
and PLC program.
Menu items 2 … 6 only appear if CODESYS 2 is set as the runtime system.
Table 115: “PLC Runtime” > “Information” Submenu
Menu Item
0. Back to …
1. Runtime Version
2. Webserver Version
3. State
4. Number of Tasks
5. Project Details
6. Tasks
Explanation
Back to the higher-level menu
Opens a submenu to display the runtime version
Opens a submenu to display the Webserver version
Opens a submenu to display the PLC operating state
Opens a submenu to display the number of tasks in
the PLC program
Opens a submenu to display the PLC program
project information
Opens a submenu to display the tasks in the PLC
program
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
166
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.2.3.2 “Information” > “Runtime Version” Submenu
In this submenu, the runtime version is displayed.
Table 116: “PLC Runtime” > “Information” > “Runtime Version” Submenu
Parameters
Version
Explanation
The version of the currently enabled runtime system
is shown. If the runtime system is disabled, “None”
is displayed.
To return to the higher-level menu, press [Q] or [Return].
7.8.2.3.3 “Information” > “Webserver Version” Submenu
In this submenu, the Webserver version is displayed.
The submenu only appears when CODESYS 2 is enabled as the runtime system.
Table 117: “PLC Runtime” > “Information” > “Webserver Version” Submenu
Parameters
Version
Explanation
The Webserver version is displayed.
To return to the higher-level menu, press [Q] or [Return].
7.8.2.3.4 “Information” > “State” Submenu
In this submenu, the PLC operating state is displayed.
The submenu only appears when CODESYS 2 is enabled as the runtime system.
Table 118: “PLC Runtime” > “Information” > “State” Submenu
Parameters
State
Explanation
The PLC operating state is shown.
STOP
PLC program is not executed.
RUN
PLC program is executed.
To return to the higher-level menu, press [Q] or [Return].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
167
7.8.2.3.5 “Information” > “Number of Tasks” Submenu
In this submenu, the number of tasks in the PLC program are displayed.
The submenu only appears when CODESYS 2 is enabled as the runtime system.
Table 119: “PLC Runtime” > “Information” > “Number of Tasks” Submenu
Parameters
Number of Tasks
Explanation
The number of tasks in the PLC program is shown.
To return to the higher-level menu, press [Q] or [Return].
7.8.2.3.6 “Information” > “Project Details” Submenu
In this submenu, project information from the PLC program is displayed.
The submenu only appears when CODESYS 2 is enabled as the runtime system
and the program is executed.
Table 120: “PLC Runtime” > “Information” > “Project Details” Submenu
Parameters
Date
Title
Version
Author
Description
Explanation
Display of project information that the programmer
entered in the PLC program (in the programming
software under Project > Project Information ...)
Descriptive text with up to 1024 characters is
displayed under “Description”.
To return to the higher-level menu, press [Q] or [Return].
7.8.2.3.7 “Information” > “Tasks” Submenu
In this submenu, tasks from the PLC program are displayed. An entry is generated
for each task.
The submenu only appears when CODESYS 2 is enabled as the runtime system.
Table 121: “PLC Runtime” > “Information” > “Tasks” Submenu
Menu Item
0. Back to …
n. Task n
Explanation
Back to the higher-level menu
Opens a submenu with information on the selected
task
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
168
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.2.3.8 “Tasks” > “Task n” Submenu
In this submenu, information on the selected task is displayed.
The submenu only appears when CODESYS 2 is enabled as the runtime system.
Table 122: “PLC Runtime” > “Information” > “Tasks” > “Task n” Submenu
Parameters
Cycle count
Cycle time (µsec)
Cycle time min (µsec)
Cycle time max (µsec)
Cycle time avg (µsec)
Status
Mode
Priority
Interval (msec)
Explanation
Number of task cycles since the system start
Currently measured task cycle time for the task
Minimum task cycle time for the task since the
system start
Maximum task cycle time for the task since the
system start
Average task cycle time since the system start
Task status (e.g., RUN, STOP)
Task execution mode (e.g., in cycles)
Set task priority
Set task interval
To return to the higher-level menu, press [Q] or [Return].
7.8.2.3.9 “PLC Runtime” > “General Configuration” Submenu
This submenu contains other submenus with general settings for the runtime
system.
Table 123: “PLC Runtime” > “General Configuration” Submenu
Menu Item
0. Back to …
1. PLC Runtime Version
2. Home Dir On SD Card
Explanation
Back to the higher-level menu
Opens a submenu for the CODESYS runtime system
settings
Opens a submenu for the home directory settings
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
169
7.8.2.3.10 “General Configuration” > “PLC Runtime Version” Submenu
In this submenu, select which PLC runtime system is enabled.
Table 124: “PLC Runtime” > “General Configuration” > “PLC Runtime Version” Submenu
Menu Item
0. Back to …
1. None
2. CODESYS 2
3. e!RUNTIME
Explanation
Back to the higher-level menu
No runtime system is enabled.
The CODESYS 2 runtime system is enabled.
The e!RUNTIME runtime system is enabled.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
7.8.2.3.11 “General Configuration” > “Home Dir On SD Card” Submenu
In this submenu, define if the home directory for the runtime system should be
moved to the memory card.
Table 125: “PLC Runtime” > “General Configuration” > “Home Dir On SD Card” Submenu
Menu Item
0. Back to …
1. Enable
2. Disable
Explanation
Back to the higher-level menu
The home directory is moved to the memory card.
The home directory is stored in the internal memory.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
170
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.2.3.12 “PLC Runtime” > “WebVisu” Submenu
This submenu contains information and settings for the Web visualization.
Table 126: “PLC Runtime” > “WebVisu” Submenu
Menu Item
0. Back to …
1. CODESYS 2 Webserver
State
2. e!RUNTIME Webserver
State
3. Default Webserver
Submenu Item / Explanation
Back to the higher-level menu
The status of the CODESYS 2 Webserver is
displayed.
The status of the e!RUNTIME Webserver is
displayed.
Choose here whether the Web-based Management or
web visualization of the runtime system should be
displayed when only entering the IP address of the
controller.
0. Back to … Back to the higher-level menu
1. Web-based
The Web-based Management is
Managem
displayed.
ent
2. CODESYS The web visualization of the runtime
WebVisu system is displayed.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Pos : 52.6 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
171
Pos : 52.7 /Serie 750 (WAGO-I/O-SYST EM)/C ons ol e-Based-Management- System C BM/PFC xxx/CBM PFC xxx M enü "N etwor king" @ 24\mod_1445418903399_21.doc x @ 194058 @ 45555555555555 @ 1
7.8.2.4
“Networking” Menu
This menu contains other submenus with settings for the network configuration.
Table 127: “Networking” Menu
Parameters
0. Back to …
1. Host/Domain Name
2. TCP/IP
3. Ethernet
Explanation
Back to the higher-level menu
Opens a submenu with setting options for the general
TCP/IP parameters
Opens a submenu with TCP/IP settings for the
ETHERNET interfaces
Opens a submenu with settings for the ETHERNET
configuration
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
7.8.2.4.1 “Networking” > “Host/Domain Name” Submenu
This submenu contains the “Hostname” and “Domain Name” submenu with
setting options for the general TCP/IP parameters.
Table 128: “Networking” > “Host/Domain Name” Submenu
Parameters
0. Back to …
1. Hostname
2. Domain Name
Explanation
Back to the higher-level menu
Opens a submenu with the hostname settings
In addition to the menu item, the configured and
current hostname are displayed.
Opens a submenu hostname settings
In addition to the menu item, the configured and
current domain name are displayed.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
172
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.2.4.2 “Host/Domain Name” > “Hostname” Submenu
In this submenu, you can set the hostname of the controller.
Table 129: “Networking” > “Hostname” Submenu
Parameters
Enter new Hostname
Explanation
Enter here the hostname of the controller to be used
if the network interface is changed to a static IP
address or if no hostname is transmitted with a
DHCP response.
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
7.8.2.4.3 “Host/Domain Name” > “Domain Name” Submenu
In this submenu, you can set the domain name of the controller.
Table 130: “Networking” > “Host/Domain Name” > “Domain Name” Submenu
Parameters
Enter new Domain Name
Explanation
Enter the domain name.
The default entry is “localdomain.lan”.
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
7.8.2.4.4 “Networking” > “TCP/IP” Submenu
This submenu contains other submenus with the TCP/IP settings for the
ETHERNET interfaces.
Table 131: “Networking” > “TCP/IP” Submenu
Menu Item
0. Back to …
1. IP Address
2. Default Gateway
3. DNS Server
Explanation
Back to the higher-level menu
Opens a submenu with settings for the IP address(es)
Opens a submenu with settings for the default
gateway
Opens a submenu with settings for the DNS server(s)
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
173
7.8.2.4.5 “TCP/IP” > “IP Address” Submenu
This submenu contains other submenus with settings for the ETHERNET
interfaces.
The submenu only appears if the controller is operated in “Separated” mode.
If the controller is operated in “Switched” mode, then the “IP Address” > “X1”
submenu is displayed directly.
Table 132: “Networking” > “IP Address” Submenu
Menu Item
0. Back to …
1. X1
2. X2
Explanation
Back to the higher-level menu
Opens a submenu with settings for the X1 interface
Opens a submenu with settings for the X2 interface
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
7.8.2.4.6 “IP Address” > “Xn“ Submenu
This submenu contains the settings for the selected interface.
Table 133: “Networking” > “TCP/IP” > “IP Address” Submenu > “Xn”
Menu Item
0. Back to …
1. Type of IP Address
Configuration
2. IP Address
3. Subnet Mask
Submenu Item / Explanation
Back to the higher-level menu
Select a static or dynamic IP address.
0. Back to … Back to the higher-level menu
Static IP addressing
When selecting static addressing, the
1. Static IP
IP address and subnet mask are then
retrieved.
2. DHCP
Dynamic IP addressing
3. BootP
Dynamic IP addressing
Enter here a static IP address.
Enter the subnet mask.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
174
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.2.4.7 “TCP/IP” > “Default Gateway” Submenu
This submenu contains other submenus with settings for the default gateway.
Table 134: “Networking” > “TCP/IP” > “Default Gateway” Submenu
Menu Item
0. Back to …
1. Default Gateway 1
2. Default Gateway 2
Explanation
Back to the higher-level menu
Opens a submenu with settings for default gateway 1
In addition to the menu item, the current status of the
gateway is displayed.
Opens a submenu with settings for default gateway 2
In addition to the menu item, the current status of the
gateway is displayed.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
7.8.2.4.8 “Default Gateway” > “Default Gateway n” Submenu
This submenu contains the settings for the selected gateway.
Table 135: “Networking” > “TCP/IP” > “Default Gateway” > “Default Gateway n” Submenu
Menu Item
0. Back to …
1. State
2. Gateway IP Address
3. Gateway Metric
Submenu Item / Explanation
Back to the higher-level menu
Set here whether the selected default gateway is to
be used.
0. Back to … Back to the higher-level menu
1. Disabled The default gateway is not used.
2. Enabled
The default gateway is used.
Enter the address of the default gateway.
Set here a number as the metric.
The default value for the metric is 20, the lowest
value is 0, the highest value is 4.294.967.295.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
175
7.8.2.4.9 “TCP/IP” > “DNS Server” Submenu
This submenu contains the settings for the DNS server.
Table 136: “Networking” > “TCP/IP” > “DNS Server” Submenu
Menu Item
0. Back to …
n. DNS Server n
(n+1). Add new DNS
Server
Submenu Item / Explanation
Back to the higher-level menu
The addresses of the defined DNS servers are
displayed. Other submenus are available for the
server entered.
0. Back to … Back to the higher-level menu
You can change the selected DNS
1. Edit
server address.
You can delete the selected DNS
2. Delete
server address.
Add additional DNS server addresses.
You can enter 10 addresses.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
7.8.2.4.10 “Networking” > “Ethernet” Submenu
This submenu contains other submenus with settings for the ETHERNET
configuration.
Table 137: “Networking” > “Ethernet” Submenu
Menu Item
0. Back to …
1. Switch Configuration
2. Ethernet Ports
Explanation
Back to the higher-level menu
Opens a submenu with settings for the IP address(es)
Opens a submenu with settings for the ETHERNET
interfaces
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
176
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.2.4.11 “Ethernet” > “Switch Configuration” Submenu
This submenu contains the settings for the Switch configuration.
Table 138: “Networking” > “Ethernet” > “Switch Configuration” Submenu
Submenu
0. Back to …
1. Network interfaces
Submenu Item / Explanation
Back to the higher-level menu
Enable or disable the switch.
0. Back to … Back to the higher-level menu
Each interface is operated with its
1. Separated
own IP address.
Both interfaces are operated with one
2. Switched
IP address.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
7.8.2.4.12 “Ethernet” > “Ethernet Ports” Submenu
This submenu contains other submenus with settings for the ETHERNET
interfaces.
Table 139: “Networking” > “Ethernet” > “Ethernet Ports” Submenu
Menu Item
0. Back to …
1. Interface X1
2. Interface X2
Explanation
Back to the higher-level menu
Opens a submenu with settings for the X1 interface
Opens a submenu with settings for the X2 interface
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
7.8.2.4.13 “Ethernet Ports” > “Interface Xn” Submenu
This submenu contains the settings for the selected ETHERNET interface.
Table 140: “Networking” > “Ethernet” > “Ethernet Ports” > “Interface Xn” Submenu
Submenu
0. Back to …
Submenu Item / Explanation
Back to the higher-level menu
Set here whether the selected port is to be used.
1. Port
0. Back to … Back to the higher-level menu
1. Disabled The port is not used.
2. Enabled
The port is used.
Set here whether the Autonegotiation function is
enabled for the selected port.
0. Back to … Back to the higher-level menu
1. Disabled Autonegotiation is disabled.
2. Enabled
Autonegotiation is enabled.
2. Autonegotiation
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Pos : 52.8 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
177
178
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 52.9 /Serie 750 (WAGO-I/O-SYST EM)/C ons ol e-Based-Management- System C BM/PFC xxx/CBM PFC xxx M enü "Firewall", <= F W06 @ 24\mod_1447667334230_21.doc x @ 195644 @ 45555555 @ 1
7.8.2.5
“Firewall” Menu
This menu contains other submenus for the firewall functionality settings.
Table 141: “Firewall” Menu
Menu Item
0. Back to …
1. General Configuration
2. MAC Address Filter
3. User Filter
Explanation
Back to the higher-level menu
Opens a submenu with general firewall settings
Opens a submenu with MAC address filter settings
Opens a submenu with user filter settings
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
179
7.8.2.5.1 “Firewall” > “General Configuration” Submenu
This submenu contains the general settings for the firewall.
Table 142: “Firewall” > “General Configuration” Submenu
Menu Item
0. Back to …
Submenu Item / Explanation
Back to the higher-level menu
Enables/disables the complete functionality of the
firewall.
1. Firewall enabled entirely 0. Back to … Back to the higher-level menu
1. Enable
Firewall is enabled.
2. Disable
Firewall is disabled.
Enable or disable the “ICMP echo broadcast”
protection.
0. Back to … Back to the higher-level menu
2. ICMP echo broadcast
“ICMP echo broadcast” protection is
protection
1. Enable
enabled.
“ICMP echo broadcast” protection is
2. Disable
disabled.
You can specify the maximum number of UDP
3. Max UDP connections
connections per second.
per second
“0” = “Disabled”
You can specify the maximum number of TCP
4. Max TCP connections
connections per second.
per second
“0” = “Disabled”
5. Interface WAN
6. Interface VPN
Opens a submenu with firewall settings on the IP
level for the selected interface
7. Interface X1
8. Interface X2
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
180
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.2.5.2 “General Configuration” > “Interface xxx” Submenu
This submenu contains the firewall settings on the IP level for the selected
interface.
Table 143: “Firewall” > “General Configuration” > “Interface xxx” Submenu
Menu Item
0. Back to …
1. Interface state
2. ICMP Policy
3. ICMP Limit
4. ICMP Burst
Submenu Item / Explanation
Back to the higher-level menu
Enable or disable the firewall for the selected
interface.
0. Back to … Back to the higher-level menu
The firewall for the selected interface
1. Open
is disabled.
The firewall for the selected interface
2. Filtered
is enabled.
Enable or disable the “ICMP echo” protection for the
respective interface.
0. Back to … Back to the higher-level menu
The “ICMP echo” protection is
1. Accept
disabled.
The “ICMP echo” protection is
2. Drop
enabled.
You can specify the maximum number of “ICMP
pings” per second.
“0” = “Disabled”
You can specify the maximum number of “ICMP
echo bursts” per second.
“0” = “Disabled”
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
181
7.8.2.5.3 “Firewall” > “MAC Address Filter” Submenu
This submenu contains the settings for the MAC address filter.
Table 144: “Firewall” > “MAC Address Filter” Submenu
Menu Item
0. Back to …
1. MAC address filter
whitelist
2. MAC address filter state
VPN
3. MAC address filter state
WAN
4. MAC address filter state
X1
5. MAC address filter state
X2
Submenu Item / Explanation
Back to the higher-level menu
Opens a submenu to edit the MAC address filter
whitelist
Enable or disable the firewall for the VPN interface.
0. Back to … Back to the higher-level menu
The firewall for the VPN interface is
1. Open
disabled.
The firewall for the VPN interface is
2. Filtered
enabled.
Enable or disable the firewall for the WAN interface.
0. Back to … Back to the higher-level menu
The firewall for the WAN interface is
1. Open
disabled.
The firewall for the WAN interface is
2. Filtered
enabled.
Enable or disable the firewall for the X1 interface.
0. Back to … Back to the higher-level menu
The firewall for the X1 interface is
1. Open
disabled.
The firewall for the X1 interface is
2. Filtered
enabled.
Enable or disable the firewall for the X2 interface.
0. Back to … Back to the higher-level menu
The firewall for the X2 interface is
1. Open
disabled.
The firewall for the X2 interface is
2. Filtered
enabled.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
182
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.2.5.4 “MAC Address Filter” > “MAC address filter whitelist” Submenu
This submenu displays all available filter entries.
Table 145: “Firewall” > “MAC Address Filter” > “MAC address filter whitelist” Submenu
Menu Item
0. Back to …
1. Add new
2. Previous page
3. Next Page
(n + 3.) No (n):
Explanation
Back to the higher-level menu
Opens a submenu to add a new filter entry
Displays the previous page of the list (if more than
one page is filled)
Displays the next page of the list (if more than one
page is filled)
Opens a submenu to edit an existing filter entry
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
7.8.2.5.5 “MAC address filter whitelist” > “Add new / No (n)” Submenu
In this submenu, you can create, change or delete filter entries.
Table 146: “Firewall” > “MAC Address Filter” > “MAC address filter whitelist” > “Add new / No
(n)” Submenu
Menu Item
0. Back to …
1. MAC address
2. MAC mask
3. Filter state
4. accept
5. delete
Submenu Item / Explanation
Back to the higher-level menu
Enter the MAC address.
Enter the MAC mask.
Enable or disable the filter.
0. Back to … Back to the higher-level menu
1. on
The filter is enabled.
2. off
The filter is disabled.
To apply the changes for the selected filter entry,
choose this menu item.
To delete the selected filter entry, choose this menu
item.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
183
7.8.2.5.6 “Firewall” > “User Filter” Submenu
This submenu displays all available filter entries.
Table 147: “Firewall” > “User Filter” Submenu
Menu Item
0. Back to …
1. Add new
2. Previous page
3. Next Page
(n + 3.) No (n):
Explanation
Back to the higher-level menu
Opens a submenu to add a new filter entry
Displays the previous page of the list (if more than
one page is filled)
Displays the next page of the list (if more than one
page is filled)
Opens a submenu to edit an existing filter entry
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
184
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.2.5.7 “User Filter” > “Add New / No (n)” Submenu
In this submenu, you can create, change or delete filter entries.
Table 148: “Firewall” > “User Filter” > “Add New / No (n)” Submenu
Menu Item
0. Back to …
1. Source IP address
2. Source netmask
3. Source port
4. Destination IP address
5. Destination netmask
6. Destination port
7. protocol
8. interface
9. state
10. accept
11. delete
Submenu Item / Explanation
Back to the higher-level menu
Enter the source IP address.
Enter the source network mask.
Enter the source port number.
Enter the destination IP address.
Enter here the destination netmask.
Enter the destination port number.
Select the permitted protocols.
0. Back to … Back to the higher-level menu
1. tcp
The TCP protocol is permitted.
2. udp
The UDP protocol is permitted.
3. tcp & udp Both protocols are permitted.
Select the permitted interfaces.
0. Back to … Back to the higher-level menu
1. all
All interfaces are permitted.
2. VPN
The VPN interface is permitted.
3. WAN
The WAN interface is permitted.
4. X1
The X1 interface is permitted.
5. X2
The X2 interface is permitted.
Enable or disable the filter.
0. Back to … Back to the higher-level menu
1. on
The filter is enabled.
2. off
The filter is disabled.
To apply the changes for the selected filter entry,
choose this menu item.
To delete the selected filter entry, choose this menu
item.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
Pos : 52.10 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
185
Pos : 52.11 /Serie 750 ( WAGO-I/O-SYST EM)/Cons ole- Bas ed-Manag ement-System C BM/PFC xxx/C BM PFC xxx Menü "Cloc k" @ 24\mod_1447673931217_21.doc x @ 195663 @ 4 @ 1
7.8.2.6
“Clock” Menu
This menu contains other submenus for the date and time settings.
Table 149: “Clock” Menu
Menu Item
0. Back to …
1. Date on device (local)
2. Time on device (local)
3. Time on device (UTC)
4. Clock Display Mode
5. Timezone
6. TZ String
Submenu Item / Explanation
Back to the higher-level menu
Set date.
Set local time.
Set GMT time.
Select the display format for the time.
0. Back to … Back to the higher-level menu
The time is displayed in 24-hour
1. 24 hours
format.
The time is displayed in 12-hour
2. 12 hours
format.
Specify the appropriate time zone for your location.
Basic setting:
0. Back to … Back to the higher-level menu
1. AST/ADT “Atlantic Standard Time,” Halifax
“Eastern Standard Time,” New York,
2. EST/EDT
Toronto
“Central Standard Time,” Chicago,
3. CST/CDT
Winnipeg
4. MST/
“Mountain Standard Time,” Denver,
MDT
Edmonton
“Pacific Standard Time”, Los
5. PST/PDT
Angeles, Whitehouse
Greenwich Mean Time,“ GB, P, IRL,
6. GMT/BST
IS, …
7. CET/
“Central European Time,” B, DK, D,
CEST
F, I, CRO, NL, …
8. EET/
“East European Time,” BUL, FI, GR,
EEST
TR, …
9. CST
“China Standard Time”
10. JST
“Japan/Korea Standard Time”
Enter the name of your time zone or country and
town if the time zone is not available for selection
using the “Timezone” parameter.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
Pos : 52.12 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
186
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 52.13 /Serie 750 ( WAGO-I/O-SYST EM)/Cons ole- Bas ed-Manag ement-System C BM/PFC xxx/C BM PFC xxx Menü "Adminis trati on" mit R S-232 @ 24\mod_1447849178992_21.doc x @ 195798 @ 455 @ 1
7.8.2.7
“Administration” Menu
This menu contains settings for controller administration.
Table 150: “Administration” Menu
Menu Item
0. Back to …
Submenu Item / Explanation
Back to the higher-level menu
Opens a submenu with settings for the user
1. Users
passwords
2. Create Image
Opens a submenu for creating a bootable image
Select the serial interface assignment.
0. Back to … Back to the higher-level menu
1. Linux
The serial interface is assigned to the
3. Owner of Serial Interface
Console Linux® console.
The serial interface is not assigned
2. Unand is available for applications or
assigned
CODESYS.
Restart the controller following a security challenge.
4. Reboot Controller
0. Back to … Back to the higher-level menu
1. Reboot
Restarts the controller
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
187
7.8.2.7.1 “Administration” > “Create Image” Submenu
This submenu contains the selection for creating the image.
In addition to the menu item for the enabled storage medium, the current status is
displayed.
Table 151: “Administration” > “Create Image” Submenu
Menu Item
0. Back to …
1. SD Card
2. Internal Flash
Explanation
Back to the higher-level menu
To create an image on the memory card, select this
menu item. Enter the reserved memory size in
another step.
This menu item only appears if the memory card is
inserted.
To create an image on the internal memory, select
this menu item.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
7.8.2.7.2 “Administration” > “Users” Submenu
This submenu contains settings for the user passwords.
Table 152: “Administration” > “Users” Submenu
Menu Item
0. Back to …
1. user
2. admin
Explanation
Back to the higher-level menu
Enter a new password for the “user” user.
Enter a new password for the “admin” user.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
Pos : 52.14 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
188
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 52.15 /Serie 750 ( WAGO-I/O-SYST EM)/Cons ole- Bas ed-Manag ement-System C BM/PFC xxx/C BM PFC xxx Menü "Pac kage Ser ver" @ 24\mod_1448443374435_21.doc x @ 196211 @ 4555555 @ 1
7.8.2.8
“Package Server” Menu
This menu contains other submenus with functions for firmware backup and
restore, as well as information and setting options for the current system partition.
Table 153: “Package Server” Menu
Menu Item
0. Back to …
1. Firmware Backup
2. Firmware Restore
3. System Partition
Explanation
Back to the higher-level menu
Opens a submenu with functions for the firmware
backup
Opens a submenu with functions for the firmware
restore
Opens a submenu with information and setting
options for the current system partition
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
7.8.2.8.1 “Package Server” > “Firmware Backup” Submenu
This submenu contains a selection option for the data to be saved.
The submenu only appears if a memory card is inserted that does not contain a
bootable system. Otherwise, a message is displayed.
Table 154: “Package Server” > “Firmware Backup” Menu
Menu Item
0. Back to …
1. All
2. PLC Runtime project
3. Settings
4. System
Explanation
Back to the higher-level menu
All data is saved.
The PLC runtime project is saved.
The controller settings are saved.
The controller operating system is saved.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
You are taken to the following submenu after making the selection.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
189
7.8.2.8.2 “Firmware Backup” > “Auto Update Feature” Submenu
This submenu contains a setting option for the Auto Update function.
The submenu only appears if the data for the firmware backup has been selected.
Table 155: “Package Server” > “Firmware Backup” > “Auto Update Feature” Menu
Menu Item
0. Back to …
1. No
2. Yes
Explanation
Back to the higher-level menu
The Auto Update function is OFF for the selected
data.
The Auto Update function is ON for the selected
data.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
You are taken to the following submenu after making the selection.
7.8.2.8.3 “Firmware Backup” > “Destination” Submenu
This submenu contains a selection option for the backup destination drive.
Table 156: “Package Server” > “Firmware Backup” > “Auto Update Feature” Menu
Menu Item
0. Back to …
1. SD Card
Explanation
Back to the higher-level menu
The selected data is copied to the memory card.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
The copy progress is displayed during the backup process.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
190
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.2.8.4 “Package Server” > “Firmware Restore” Submenu
This submenu contains a selection option for the restore source drive.
In addition to the enabled partition, the current status is displayed.
Table 157: “Package Server” > “Firmware Restore” Menu
Menu Item
0. Back to …
1. SD Card
2. Internal Flash
Explanation
Back to the higher-level menu
The data is copied from the memory card.
The data is copied from the internal memory.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
You are taken to the following submenu after making the selection.
7.8.2.8.5 “Firmware Restore” > “Select Package” Submenu
This submenu contains a selection option for the data to be restored.
Table 158: “Package Server” > “Firmware Restore” > “Select Package” Menu
Menu Item
0. Back to …
1. PLC Runtime project
2. Settings
3. System
4. System + Setting
5. All
Explanation
Back to the higher-level menu
The PLC runtime project is loaded.
The controller settings are loaded.
The controller operating system is loaded.
The controller operating system and settings are
loaded.
All data is loaded.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
The copy progress is displayed during the restore process.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
7.8.2.8.6 “Package Server” > “System Partition” Submenu
This submenu contains information and setting options for the current system
partition.
Table 159: “Package Server” > “System Partition” Submenu
Menu Item
0. Back to …
1. Current active partition
2. Set inactive NAND
partition active
Explanation
Back to the higher-level menu
The partition currently in use is displayed.
Select this menu item to start the system from a
different partition at the next controller reboot.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Pos : 52.16 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
191
192
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 52.17 /Serie 750 ( WAGO-I/O-SYST EM)/Cons ole- Bas ed-Manag ement-System C BM/PFC xxx/C BM PFC xxx Menü "Mas s Stor age" @ 24\mod_1447936746590_21.doc x @ 195828 @ 45 @ 1
7.8.2.9
“Mass Storage” Menu
This menu contains information on the internal flash memory and, if inserted, on
the external memory card.
In addition to the menu item, the status is displayed for the enabled partition.
Table 160: “Mass Storage” Menu
Parameters
0. Back to …
1. SD Card
2. Internal Flash
Explanation
Back to the higher-level menu
Opens a submenu with information on the memory
card and its formatting
This menu item only appears if a memory card is
inserted in the controller.
Opens a submenu with information on the internal
flash memory
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
7.8.2.9.1 “Mass Storage” > “SD Card” Submenu
This submenu contains information on the external memory card and its
formatting.
This submenu only appears if a memory card is inserted in the controller.
Table 161: “Mass Storage” > “SD Card” Menu
Parameters
0. Back to …
1. Show information
2. FAT format medium
Explanation
Back to the higher-level menu
Displays information on the memory card
To format the memory card in FAT format, select
this menu item. Then specify a volume name.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
Pos : 52.18 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
Pos : 52.19 /Serie 750 ( WAGO-I/O-SYST EM)/Cons ole- Bas ed-Manag ement-System C BM/PFC xxx/C BM PFC xxx Menü "Softwar e U ploads" @ 24\mod_1448443273604_21.doc x @ 196208 @ 4 @ 1
7.8.2.10
“Software Uploads” Menu
This menu contains choices and settings for the device update.
You can select fieldbus software, program licenses and update scripts, for
example, for transfer from a PC to the controller.
You can also enable transmitted packages or delete from the controller.
Pos : 52.20 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
193
194
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 52.21 /Serie 750 ( WAGO-I/O-SYST EM)/Cons ole- Bas ed-Manag ement-System C BM/PFC xxx/C BM PFC xxx Menü "Ports and Ser vices", C ODESYS 2 und e!RUNTIME @ 24\mod_1447743945043_21.doc x @ 195708 @ 4555555555555555555 @ 1
7.8.2.11
“Ports and Services” Menu
This submenu contains other submenus with settings for the respective services.
Table 162: “Ports and Services” Menu
Menu Item
0. Back to …
1. Telnet
2. FTP
3. FTPS
4. HTTP
5. HTTPS
6. NTP
7. SSH
8. TFTP
9. DHCPD
10. DNS
11. IOCHECK PORT
12. Modbus TCP
13. Modbus UDP
14. PLC Runtime Services
Explanation
Back to the higher-level menu
Opens a submenu with settings for the Telnet service
Opens a submenu with settings for the FTP service
Opens a submenu with settings for the FTPS service
Opens a submenu with settings for the HTTP service
Opens a submenu with settings for the HTTPS
service
Opens a submenu with settings for the NTP service
Opens a submenu with settings for the SSH server
Opens a submenu with settings for the TFTP server
Opens a submenu with settings for the DHCPD
service
Opens a submenu with settings for the DNS service
Opens a submenu with settings for the WAGO-I/OCHECK port
Opens a submenu with settings for the MODBUS
TCP service
Opens a submenu with settings for the MODBUS
UDP service
Opens a submenu with settings for the PLC runtime
system services
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
195
7.8.2.11.1 “Ports and Services” > “Telnet” Submenu
This submenu contains the settings for the Telnet service.
Table 163: “Ports and Services” > “Telnet” Submenu
Menu Item
0. Back to …
1. State
2. Firewall status
Submenu Item / Explanation
Back to the higher-level menu
Enable/disable the Telnet service.
0. Back to … Back to the higher-level menu
1. Enable
The Telnet service is enabled.
2. Disable
The Telnet service is disabled.
Opens a submenu with firewall settings for the this
service for the interfaces
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
7.8.2.11.2 “Ports and Services” > “FTP” Submenu
This submenu contains the settings for the FTP service.
Table 164: “Ports and Services” > “FTP” Submenu
Menu Item
0. Back to …
1. State
2. Firewall status
Submenu Item / Explanation
Back to the higher-level menu
Enable/disable the FTP service.
0. Back to … Back to the higher-level menu
1. Enable
The FTP service is enabled.
2. Disable
The FTP service is disabled.
Opens a submenu with firewall settings for the this
service for the interfaces
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
196
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.2.11.3 “Ports and Services” > “FTPS” Submenu
This submenu contains the settings for the FTPS service.
Table 165: “Ports and Services” > “FTPS” Submenu
Menu Item
0. Back to …
1. State
2. Firewall status
Submenu Item / Explanation
Back to the higher-level menu
Enable/disable the FTPS service.
0. Back to … Back to the higher-level menu
1. Enable
The FTPS service is enabled.
2. Disable
The FTPS service is disabled.
Opens a submenu with firewall settings for the this
service for the interfaces
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
7.8.2.11.4 “Ports and Services” > “HTTP” Submenu
This submenu contains the settings for the HTTP service.
Table 166: “Ports and Services” > “HTTP” Submenu
Menu Item
0. Back to …
1. State
2. Firewall status
Submenu Item / Explanation
Back to the higher-level menu
Enable/disable the HTTP service.
0. Back to … Back to the higher-level menu
1. Enable
The HTTP service is enabled.
2. Disable
The HTTP service is disabled.
Opens a submenu with firewall settings for the this
service for the interfaces
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
197
7.8.2.11.5 “Ports and Services” > “HTTPS” Submenu
This submenu contains the settings for the HTTPS service.
Table 167: “Ports and Services” > “HTTPS” Submenu
Menu Item
0. Back to …
1. State
2. Firewall status
Submenu Item / Explanation
Back to the higher-level menu
Enable/disable the HTTPS service.
0. Back to … Back to the higher-level menu
1. Enable
The HTTPS service is enabled.
2. Disable
The HTTPS service is disabled.
Opens a submenu with firewall settings for the this
service for the interfaces
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
7.8.2.11.6 “Ports and Services” > “NTP” Submenu
This submenu contains the settings for the NTP service.
Table 168: “Ports and Services” > “NTP” Submenu
Menu Item
0. Back to …
1. State
2. Port
3. Time Server 1
4. Time Server 2
5. Time Server 3
6. Time Server 4
7. Update Time
8. Issue immediate update
Submenu Item / Explanation
Back to the higher-level menu
Enable/disable the NTP service.
0. Back to … Back to the higher-level menu
1. Enable
The NTP service is enabled.
2. Disable
The NTP service is disabled.
Enter the port number of the NTP server.
Enter here the IP addresses of up to 4 time servers.
Time server No. 1 is requested first of all. If no data
can be accessed via time server No. 1, time server
No. 2 is requested.
Specify here the update interval of the time server.
To update the time immediately, irrespective of the
update interval, select this menu item.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
198
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.2.11.7 “Ports and Services” > “SSH” Submenu
This submenu contains the settings for the SSH service.
Table 169: “Ports and Services” > “SSH” Submenu
Menu Item
0. Back to …
1. State
2. Port
3. Allow root login
4. Allow password login
5. Status of firewalling
Submenu Item / Explanation
Back to the higher-level menu
You can enable/disable the SSH server.
0. Back to … Back to the higher-level menu
1. Enable
The SSH server is enabled.
2. Disable
The SSH server is disabled.
Enter the port number.
You can enable or inhibit root access.
0. Back to … Back to the higher-level menu
1. Enable
Root access is permitted.
2. Disable
Root access is not permitted.
Enable or disable the password query function.
0. Back to … Back to the higher-level menu
1. Enable
Password query is enabled.
2. Disable
Password query is disabled.
Opens a submenu with firewall settings for the this
service for the interfaces
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
7.8.2.11.8 “Ports and Services” > “TFTP” Submenu
This submenu contains the settings for the TFTP service.
Table 170: “Ports and Services” > “TFTP” Submenu
Menu Item
0. Back to …
1. State
2. Transfer Directory
3. Status of firewalling
Submenu Item / Explanation
Back to the higher-level menu
Enable or disable the TFTP server.
0. Back to … Back to the higher-level menu
1. Enable
The TFTP server is enabled.
2. Disable
The TFTP server is disabled.
Specify here the path for downloading the server
directory.
Opens a submenu with firewall settings for the this
service for the interfaces
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
199
7.8.2.11.9 “Ports and Services” > “DHCPD” Submenu
This submenu contains the settings for the DHCPD service.
Table 171: “Ports and Services” > “DHCPD” Submenu
Menu Item
0. Back to …
1. DHCPD Firewalling
2. X1
3. X2
Explanation
Back to the higher-level menu
Opens a submenu with firewall settings for the this
service for the interfaces
Opens a submenu with the DHCPD settings for the
selected interface
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
7.8.2.11.10 “DHCPD” > “Xn” Submenu
This submenu contains the settings for the DHCPD service for the selected
interface.
Table 172: “Ports and Services” > “DHCPD” > “Xn” Submenu
Menu Item
0. Back to …
1. State
2. Range
3. Lease Time (min)
4. Add static hostname
(5 + n). Static Host (n)
Submenu Item / Explanation
Back to the higher-level menu
Enable/disable the DHCPD service for the Xn
interface.
0. Back to … Back to the higher-level menu
1. Enable
The DHCPD service is enabled.
2. Disable
The DHCPD service is disabled.
Enter a range of available IP addresses.
Specify the lease time here in seconds. 120 seconds
are entered by default.
Enter a new static assignment of MAC ID to IP
address,
e.g., “01:02:03:04:05:06=192.168.1.20” or
“hostname=192.168.1.20”.
You can enter 10 assignments.
This displays the static assignments.
0. Back to … Back to the higher-level menu
Opens a submenu to change the
1. Edit
selected assignment
2. Delete
Deletes the selected assignment
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
200
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.2.11.11 “Ports and Services” > “DNS” Submenu
This submenu contains the settings for the DNS service.
Table 173: “Ports and Services” > “DNS” Submenu
Menu Item
0. Back to …
1. State
2. Mode
3. Firewall status
4. Add static hostname
(5 + n). Static Host (n)
Submenu Item / Explanation
Back to the higher-level menu
Enable/disable the DNS service.
0. Back to … Back to the higher-level menu
1. Enable
The DNS service is enabled.
2. Disable
The DNS service is disabled.
Select the operating mode of the DNS server.
0. Back to … Back to the higher-level menu
The requests are buffered to optimize
1. Proxy
throughput.
2. Relay
All requests are routed directly.
Opens a submenu with firewall settings for the this
service for the interfaces
Enter a new static assignment of IP address to
hostname,
e.g., “192.168.1.20:hostname”.
You can enter 10 assignments.
This displays the static assignments.
0. Back to … Back to the higher-level menu
Opens a submenu to change the
1. Edit
selected assignment
2. Delete
Deletes the selected assignment
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
201
7.8.2.11.12 “Ports and Services” > “IOCHECK PORT” Submenu
This submenu contains settings for the WAGO-I/O-CHECK port.
Table 174: “Ports and Services” > “IOCHECK PORT” Submenu
Menu Item
0. Back to …
1. State
2. Firewall status
Submenu Item / Explanation
Back to the higher-level menu
Enable/disable the WAGO-I/O-CHECK port.
0. Back to … Back to the higher-level menu
The WAGO-I/O-CHECK port is
1. Enable
enabled.
The WAGO-I/O-CHECK port is
2. Disable
disabled.
Opens a submenu with firewall settings for the this
service for the interfaces
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
7.8.2.11.13 “Ports and Services” > “Modbus TCP” Submenu
This submenu contains the settings for the MODBUS TCP service.
Table 175: “Ports and Services” > “Modbus TCP” Submenu
Menu Item
0. Back to …
1. State
2. Firewall status
Submenu Item / Explanation
Back to the higher-level menu
Disable or enable the MODBUS/TCP service.
0. Back to … Back to the higher-level menu
The MODBUS TCP service is
1. Enable
enabled.
The MODBUS TCP service is
2. Disable
disabled.
Opens a submenu with firewall settings for the this
service for the interfaces
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
202
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.2.11.14 “Ports and Services” > “Modbus UDP” Submenu
This submenu contains the settings for the MODBUS UDP service.
Table 176: “Ports and Services” > “Modbus UDP” Submenu
Menu Item
0. Back to …
1. State
2. Firewall status
Submenu Item / Explanation
Back to the higher-level menu
Disable/enable the MODBUS UDP service.
0. Back to … Back to the higher-level menu
The MODBUS UDP service is
1. Enable
enabled.
The MODBUS UDP service is
2. Disable
disabled.
Opens a submenu with firewall settings for the this
service for the interfaces
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
7.8.2.11.15 “Ports and Services” > “PLC Runtime Services” Submenu
This submenu contains the settings for the PLC runtime system services.
Table 177: “Ports and Services” > “PLC Runtime Services” Submenu
Menu Item
0. Back to …
1. General Configuration
2. CODESYS 2
3. e!RUNTIME
4. Change CODESYS
Runtime firewalling
settings
5. Change CODESYS
WebVisu firewalling
settings
Explanation
Back to the higher-level menu
Enter the password for port authentication.
Opens a submenu with service settings for
CODESYS 2
Opens a submenu with service settings for
e!RUNTIME
Opens a submenu with firewall settings for the this
service for the interfaces
Opens a submenu with firewall settings for the this
service for the interfaces
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
203
7.8.2.11.16 “PLC Runtime Services” > “CODESYS 2” Submenu
This submenu contains the settings for the CODESYS 2 service.
Table 178: “Ports and Services” > “PLC Runtime Services” > “CODESYS 2” Submenu
Menu Item
0. Back to …
Submenu Item / Explanation
Back to the higher-level menu
Enable or disable the Webserver for the CODESYS
web visualization.
1. Webserver enable/disable 0. Back to … Back to the higher-level menu
1. Enable
The Webserver is enabled.
2. Disable
The Webserver is disabled.
Enable or disable the communication between the
CODESYS 2 runtime system and the CODESYS 2
programming system.
2. Communication
0. Back to … Back to the higher-level menu
enable/disable
1. Enable
Communication is enabled.
2. Disable
Communication is disabled.
Enter here the port number for communication with
3. Communication Port
the CODESYS 2 programming system. The default
Number
value is 2455.
Enter here whether a login is required for connecting
to the device.
4. Port Authentication
0. Back to … Back to the higher-level menu
enable/disable
1. Enable
Authentication via login is required.
2. Disable
Authentication is not required.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
204
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.2.11.17 “PLC Runtime Services” > “e!RUNTIME” Submenu
This submenu contains the settings for the e!RUNTIME service.
Table 179: “Ports and Services” > “PLC Runtime Services” > “e!RUNTIME” Submenu
Menu Item
0. Back to …
Submenu Item / Explanation
Back to the higher-level menu
Enable or disable the Webserver for the e!RUNTIME
web visualization.
1. Webserver enable/disable 0. Back to … Back to the higher-level menu
1. Enable
The Webserver is enabled.
2. Disable
The Webserver is disabled.
Enter here whether a login is required for connecting
to the device.
2. Port Authentication
0. Back to … Back to the higher-level menu
enable/disable
1. Enable
Authentication via login is required.
2. Disable
Authentication is not required.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
205
7.8.2.11.18 “…” > “Firewall Status” Submenu
This submenu contains firewall settings for the selected service.
Table 180: “Ports and Services” > “Firewall Status” Submenu
Menu Item
0. Back to …
1. VPN
2. WAN
3. X1
4. X2
Submenu Item / Explanation
Back to the higher-level menu
Enable or disable the firewall for the VPN interface
and respective service.
0. Back to … Back to the higher-level menu
Data traffic via the VPN interface is
1. open
permitted.
Data traffic via the VPN interface is
2. close
not permitted.
Enable or disable the firewall for the WAN interface
and respective service.
0. Back to … Back to the higher-level menu
Data traffic via the WAN interface is
1. open
permitted.
Data traffic via the WAN interface is
2. close
not permitted.
Enable or disable the firewall for the X1 interface
and respective service.
0. Back to … Back to the higher-level menu
Data traffic via the X1 interface is
1. open
permitted.
Data traffic via the X1 interface is not
2. close
permitted.
Enable or disable the firewall for the X2 interface
and respective service.
0. Back to … Back to the higher-level menu
Data traffic via the X2 interface is
1. open
permitted.
Data traffic via the X2 interface is not
2. close
permitted.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Pos : 52.22 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
206
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 52.23 /Serie 750 ( WAGO-I/O-SYST EM)/Cons ole- Bas ed-Manag ement-System C BM/PFC xxx/C BM PFC xxx Menü "SNM P" @ 24\mod_1448265331631_21.doc x @ 195998 @ 455555 @ 1
7.8.2.12
“SNMP” Menu
This menu contains other submenus with the SNMP settings.
Table 181: “SNMP” Menu
Parameters
0. Back to …
1. General SNMP
Configuration
2. SNMP v1/v2c Manager
Configuration
3. SNMP v1/v2c Trap
Receiver Configuration
Explanation
Back to the higher-level menu
Opens a submenu with general SNMP settings
Opens a submenu with settings for the SNMP v1/v2c
Manager
Opens a submenu with settings for the SNMP v1/v2c
trap receivers
Opens a submenu with settings for the SNMP v3
4. SNMP v3 Configuration
configuration
5. SNMP firewalling
Opens a submenu with firewall settings for SNMP
6. Secure SNMP firewalling
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
7.8.2.12.1 “SNMP” > “General SNMP Configuration” Submenu
This submenu contains the general SNMP settings.
Table 182: “SNMP” > “General SNMP Configuration” Submenu
Parameters
0. Back to …
1. SNMP status
2. Name of device
3. Description
4. Physical location
5. Contact
Submenu Item / Explanation
Back to the higher-level menu
Enable or disable the SNMP service.
0. Back to … Back to the higher-level menu
1. Enable
The SNMP service is enabled.
2. Disable
The SNMP service is disabled.
Enter here the device name (sysName).
Enter here the device description (sysDescription).
Enter here the location of the device (sysLocation).
Enter here the email contact address (sysContact).
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
207
7.8.2.12.2 “SNMP” > “SNMP v1/v2c Manager Configuration” Submenu
This submenu contains the SNMP v1/v2c Manager settings.
Table 183: “SNMP” > “SNMP v1/v2c Manager Configuration” Submenu
Parameters
0. Back to …
1. Protocol state
2. Local community name
Submenu Item / Explanation
Back to the higher-level menu
Enable or disable the SNMP v1/v2c protocol.
0. Back to … Back to the higher-level menu
The SNMP v1/v2c protocol is
1. Enable
enabled.
The SNMP v1/v2c protocol is
2. Disable
disabled.
Specify here the community name for the SNMP
manager configuration (max. 32 characters, no
spaces).
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
7.8.2.12.3 “SNMP” > “SNMP v1/v2c Trap Receiver Configuration” Submenu
This submenu contains settings for the v1/v2c trap receivers.
Table 184: “SNMP” > “SNMP v1/v2c Trap Receiver Configuration” Submenu
Parameters
0. Back to …
(n). Trap Receiver (n)
(n + 1). Add new Trap
Receiver
Explanation
Back to the higher-level menu
Opens a submenu with information on the selected
v1/v2c trap receiver to delete the trap receiver
Opens a series of submenus to create a new v1/v2c
trap receiver
You can enter 10 trap receivers.
The following entries/selections are possible:
• IP address of the new trap receiver (management
station)
• Community name for the new trap receiver
configuration (max. 32 characters, no spaces)
• SNMP version via which the traps are sent
(v1/v2c)
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
208
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.2.12.4 “SNMP” > “SNMP v3 Configuration” Submenu
This submenu contains settings for SNMP v3.
Table 185: “SNMP” > “SNMP v3 Configuration” Submenu
Parameters
0. Back to …
(n). Username
(n + 1). Add new v3 User
Explanation
Back to the higher-level menu
Opens a submenu with information on the selected
v3 user and to delete the user
Opens a series of submenus to create a new v3 user
You can enter 10 users.
The following entries/selections are possible:
• Authentication name (max. 32 characters, no
spaces)
• Authentication type (None/MD5/SHA)
• Authentication key (min. 8 characters, max. 32
characters, no spaces)
• Privacy type (None/DES/AES)
• Privacy key (min. 8 characters, max. 32
characters, no spaces)
• IP address for a trap receiver for v3 traps
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Click [<OK>] to apply the entry.
Click [<Abort>] to discard the entry.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
209
7.8.2.12.5 “SNMP” > “(Secure)SNMP firewalling” Submenu
These submenus contain the SNMP firewall settings.
Table 186: “SNMP” > “(Secure )SNMP firewalling” Submenu
Menu Item
0. Back to …
1. VPN
2. WAN
3. X1
4. X2
Submenu Item / Explanation
Back to the higher-level menu
Enable or disable the firewall for the VPN interface
and respective service.
0. Back to … Back to the higher-level menu
Data traffic via the VPN interface is
1. open
permitted.
Data traffic via the VPN interface is
2. close
not permitted.
Enable or disable the firewall for the WAN interface
and respective service.
0. Back to … Back to the higher-level menu
Data traffic via the WAN interface is
1. open
permitted.
Data traffic via the WAN interface is
2. close
not permitted.
Enable or disable the firewall for the X1 interface
and respective service.
0. Back to … Back to the higher-level menu
Data traffic via the X1 interface is
1. open
permitted.
Data traffic via the X1 interface is not
2. close
permitted.
Enable or disable the firewall for the X2 interface
and respective service.
0. Back to … Back to the higher-level menu
Data traffic via the X2 interface is
1. open
permitted.
Data traffic via the X2 interface is not
2. close
permitted.
To make a selection, choose the appropriate menu item.
To return to the higher-level menu, press [Q].
Pos : 53 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
210
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 54 /Serie 750 ( WAGO-I/O-SYST EM)/In Betrieb nehmen/Konfigurieren 750- 8xxx mi t WAGO- Ether net-Setti ngs @ 14\mod_1361451968491_21.doc x @ 112622 @ 34444 @ 1
</dg_
7.8.3
Configuration using “WAGO ETHERNET Settings”
The “WAGO ETHERNET Settings” program enables you to read system
information about your controller, make network settings and enable/disable the
Web server.
Observe the software version!
To configure the controller, use at least Version 6.4.1.1 dated 2015-06-29 or
newer of “WAGO ETHERNET Settings”!
You must select the correct COM port after starting “WAGO ETHERNET
Settings”.
Figure 47: “WAGO ETHERNET Settings” – Start Screen
For this, click “Settings” and then “Communication”.
In the “Communication settings” window that then opens, adapt the settings to
your needs.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Commissioning
211
Figure 48: “WAGO ETHERNET Settings” – Communication Link
Once you have configured “WAGO ETHERNET Settings” and have clicked
[OK], connection to the controller is established automatically.
If “WAGO ETHERNET Settings” has already been started with the correct
parameters, you can establish connection to the controller by clicking [Identify].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
212
Commissioning
7.8.3.1
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Identification Tab
An overview of the connected device is given here.
Besides some fixed values — e.g., item No., MAC address and firmware version
— the currently used IP address and the configuration method are also shown
here.
Figure 49: “WAGO ETHERNET Settings” – Identification Tab (Example)
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.3.2
Commissioning
213
Network Tab
This tab is used to configure network settings.
Values can be changed in the “Input” column, while the parameters in use are
shown in the “Currently in use” column.
Figure 50: “WAGO ETHERNET Settings” – Network Tab
Source
Specify how the controller will determine its IP address: Static, via DHCP or via
BootP.
IP address, subnet mask, gateway
Specify the specific network parameters for static configuration.
Restricted setting for default gateways!
Only the default gateway 1 can be set via “WAGO Ethernet Settings.”
The default gateway 2 can only be set in the WBM!
Preferred DNS server, alternative DNS server
Enter the IP address (when required) for an accessible DNS server when
identifying network names.
Time server
Specify the IP address for a time server if setting the controller's system time via
NTP.
Host name
The host name of the controller is displayed here. In the controller's initial state,
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
214
Commissioning
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
this name is composed of the string “PFCx00” and the last three bytes of the
MAC address.
This standard value is also used whenever the chosen name in the “Input” column
is deleted.
Domain name
The current domain name is displayed here. This setting can be automatically
overwritten with dynamic configurations, e.g., DHCP.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
7.8.3.3
Protocol Tab
Figure 51: “WAGO ETHERNET Settings” – Protocol Tab
You can enable or disable the Web server.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Commissioning
215
216
Commissioning
7.8.3.4
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Status Tab
Figure 52: “WAGO ETHERNET Settings” – Status Tab
General information about the controller status is displayed here.
The Bus extension check box has no function for the controller PFCx00, i.e., the
bus extension is always active.
Pos : 55 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Run-time System CODESYS 2.3
217
Pos : 56 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 1/Laufz eitumg ebung C ODESYS 2.3 - Ü berschrift 1 @ 14\mod_1361444759973_21.doc x @ 112516 @ 1 @ 1
8
Run-time System CODESYS 2.3
Pos : 57.1 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/Laufzei tumgebung C ODESYS 2.3Laufz eitumgebung COD ESYS 2.3 - Installation @ 14\mod_1360320595845_21.doc x @ 111220 @ 2 @ 1
8.1
Installing the CODESYS 2.3 Programming System
The WAGO target files must also be included for the installation of CODESYS.
These contain all device-specific information for the WAGO 750/758 product
series.
Proceed as described below to install the CODESYS 2.3 programming software
on a personal computer.
1.
Insert the “WAGO-I/O-PRO” CD into your computer drive.
2.
To install the programming system, follow the instructions that appear on
your screen. A successful installation is indicated by a CODESYS icon on
your desktop.
Pos : 57.2 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/Laufzei tumgebung C ODESYS 2.3Laufz eitumgebung COD ESYS 2.3 - D as erste Pr ogramm - Einl eitung @ 16\mod_1375278277345_21.doc x @ 127435 @ 23 @ 1
8.2
First Program with CODESYS 2.3
This section uses an example to explain the relevant steps required for the creation
of a CODESYS project. It is intended as a set of quick start instructions and does
not address the full functional range of CODESYS 2.3.
Additional information
For a detailed description of the full range of functions, refer to the “Manual for
PLC Programming using CODESYS 2.3” manual available on the “WAGO-I/OPRO” (759-911) CD.
8.2.1
Start the CODESYS Programming System
Start CODESYS by double clicking on the CODESYS pictogram on your desktop
using the Start menu in your operating system. To do this, click on the “Start”
button and choose Programs >
WAGO Software > CODESYS > CODESYS V2.3.
Pos : 57.3 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/Laufzei tumgebung C ODESYS 2.3Laufz eitumgebung COD ESYS 2.3 - D as erste Pr ogramm - Proj ekt anleg en und Ziels ystem 750-8202 wählen @ 16\mod_1379929205849_21.doc x @ 132460 @ 3 @ 1
8.2.2
Creating a Project and Selecting a Target System
1.
In the menu bar click on File and select New. The “Target system settings”
window then opens. Here, all available target systems that can be
programmed with CODESYS 2.3 are listed.
2.
Open the selection box in the “Target system settings” window and select
the fieldbus controller you are using. In the example shown here this is the
PFC200 CS 2ETH RS “WAGO_750-8202”.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
218
Run-time System CODESYS 2.3
3.
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Click on [OK]. The “Target system settings” configuration window then
opens.
Figure 53: Target System Settings (1)
4.
To accept the default configuration for the fieldbus controller click [OK].
The “New component” window opens.
Figure 54: Target System Settings (2)
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Run-time System CODESYS 2.3
219
5.
In this “New component” window create a new program function block. In
the example shown here, the new function block “PLC_PRG” is created in
the “ST” programming language.
6.
Click on [OK] to create the project. The programming interface opens.
Figure 55: Creating a New Function Block
Figure 56: Programming Interface With the PLC_PRG Program Module
Pos : 57.4 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/Laufzei tumgebung C ODESYS 2.3/Laufzeitumgebung C ODESYS 2.3 - D as erste Programm - Steuer ungs konf. anleg en ff. XTR- Versi on @ 23\mod_1440771133984_21.doc x @ 190510 @ 3333 @ 1
8.2.3
Creating the PLC Configuration
Procedure for Creating the PLC Configuration
The procedure explained in this section describes the PLC configuration for the
I/O modules connected to the controller.
Information about the controller function for any fieldbuses connected to the
system is given in the section on the specific fieldbus.
The PLC configuration is used to configure the fieldbus controller, along with the
connected I/O modules and to declare variables for accessing the inputs and
outputs of the I/O modules.
1.
Click on the “Resources” tab.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
220
Run-time System CODESYS 2.3
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Figure 57: “Resources” Tab
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Run-time System CODESYS 2.3
2.
In the left window double-click on “PLC configuration”. The PLC
configuration for the controller opens.
3.
Right-click on the entry “K-Bus[FIX]” and then select “Edit” in the
contextual menu. The “configuration” dialog window then opens.
221
Figure 58: Control Configuration – Edit
4.
There are three options for accepting the topology for the I/O modules
connected to the fieldbus controller. The simplest way is to scan in the
topology using WAGO-I/O-CHECK.
To do this, click on the “Start WAGO-I/O-CHECK and scan” button.
Figure 59: “Start WAGO-I/O-CHECK and Scan” Button
Ensure proper installation of WAGO-I/O-CHECK!
This function requires that the latest version of WAGO-I/O-CHECK be installed
and the IP address set under “Online > Communication parameters”, as otherwise
communication will not be possible.
5.
WAGO-I/O-CHECK is started.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
222
Run-time System CODESYS 2.3
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Figure 60: WAGO-I/O-CHECK – Starting Screen
6.
To connect to the controller and read in the module configuration, click
[Identify].
7.
If this action is successful click [Save] and exit WAGO-I/O-CHECK.
8.
The detected I/O modules then appear in the configuration window.
Passive I/O Modules
Remember that passive I/O modules, such as a power supply module
(750-602/040-000) or end module (750-600/040-000) will not be shown in the
I/O configurator.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Run-time System CODESYS 2.3
223
Figure 61: I/O Configurator Empty
9.
You can use the [Add] button to add new I/O modules to manually define or
change the configuration.
Figure 62: “Add I/O Modules” Button
10.
You can select a module in the new “Module selection” window that then
appears.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
224
Run-time System CODESYS 2.3
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Figure 63: “Module Selection” Window
11.
You can change the position of an I/O module by marking it and then using
the arrow buttons at the right edge of the window to move it up or down.
Figure 64: I/O Configurator with Defined I/O Modules
12.
Use [Import configuration from file] to add a configuration imported
previously using WAGO-I/O-CHECK.
13.
To close the I/O Configurator, click [OK].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
14.
Run-time System CODESYS 2.3
225
The individual inputs and outputs of the selected I/O module are displayed
in the right half of the configuration window.
Here, you can declare a dedicated variable in the “Name” column for each
input and output, e.g., “Output_1”, “Output_2”, “Input_1”, “Input_2”.
Figure 65: Variable Declaration
15.
The added I/O modules appear in the control configuration under
“K-Bus[FIX]” with their associated fixed addresses and, where applicable,
their previously set variable name.
Figure 66: Control Configuration: I/O Modules with Their Associated Addresses
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
226
Run-time System CODESYS 2.3
8.2.4
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Editing the Program Function Block
To edit the PLC_PRG program function block, go to the “Function block” tab and
double-click on the PLC_PRG program module.
Figure 67: Program Function Block
The following example illustrates the editing of the program function block. To
do this, an input is assigned to an output:
1.
Press [F2] to open the Input assistant, or right click and select “Input
assistant” from the contextual menu.
Figure 68: Input Assistant for Selecting Variables
2.
Under “Global variables” select the previously declared variable
“Output_1” and click [OK] to add it.
3.
Enter the allocation “=” behind the variable name.
4.
Repeat Step 2 for the “Input_1” variable.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Run-time System CODESYS 2.3
Figure 69: Example of an Allocation
5.
To compile, click on Project > Compile all in the menu bar.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
227
228
Run-time System CODESYS 2.3
8.2.5
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Loading and Running the PLC Program in the Fieldbus
Controller (ETHERNET)
Requirement:
•
The simulation is deactivated (Online > Simulation).
•
The PC is linked to the controller via ETHERNET. Refer to Section
“Device Description” > …> “ETHERNET – X1, X2 Network Connection”.
Proceed as follows:
1.
In the menu bar click on Online and select Communication parameters
…. The “Communication Parameters” window opens.
2.
To select a communication link click on [New …] in the “Communication
Parameters” window. A window opens in which you can define a
communication link.
Figure 70: Creating a Communication Link – Step 1
3.
In the “Name” field enter a designation for your fieldbus controller and then
click on “Tcp/Ip (Level 2 Route)”. Then click [OK].
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Run-time System CODESYS 2.3
229
Figure 71: Creating a Communication Link – Step 2
4.
In the “Communication Parameters” window enter the IP address of your
fieldbus controller in the “Address” field and then press Enter. To close the
window click on [OK].
To select an already created controller, select it in the left window and then
click on [OK].
Figure 72: Creating a Communication Link – Step 3
5.
Transfer the PLC program by clicking on Online in the menu bar and select
Login.
6.
Ensure that the Run/Stop switch for the fieldbus controller is set to “Run”.
7.
Start the PLC program by clicking on Online > Start in the menu bar.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
230
Run-time System CODESYS 2.3
8.2.6
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Creating a Boot Project
Create a boot project to ensure that the PLC program starts automatically again
after a fieldbus controller restart. In the menu bar select Online > Create boot
project. You must be logged in to CODESYS to use this function.
Automatic loading of the boot project
In addition, you can load the boot project automatically when starting the
fieldbus controller. Click on the “Resources” tab and open “Target system
settings”. Select the “General” tab and “Load boot project automatically”.
If a boot project (DEFAULT.PRG and DEFAULT.CHK) is present under
/home/codesys and the “Run/Stop” switch of the fieldbus controller is set to
“Run”, the fieldbus controller automatically starts with the processing of the PLC
program. The PLC program is not started if the switch is set to “Stop”.
If a PLC program is running in the fieldbus controller, a PLC task starts with the
reading of the fieldbus data (only with fieldbus controllers and fieldbus
connection), the integrated input and output data and the I/O modules. The output
data changed in the PLC program is updated after the PLC task is processed. A
change in operating mode (“Stop/Run”) is only carried out at the end of a PLC
task. The cycle time includes the time from the start of the PLC program to the
next start. If a larger loop is programmed within a PLC program, the task time is
prolonged accordingly. The inputs and outputs are updated during processing.
These updates only take place at the end of a PLC task.
Pos : 57.5 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/Laufzei tumgebung C ODESYS 2.3Laufz eitumgebung COD ESYS 2.3 - Schr eibweis e logisc her Adress en @ 16\mod_1375277375359_21.doc x @ 127420 @ 2 @ 1
8.3
Syntax of Logical Addresses
Access to individual memory elements according to IEC 61131-3 is possible
using only the following special symbols:
Table 187: Syntax of Logical Addresses
Item
Prefix
Description
1
%
Starts the absolute address
2
I
Input
Q
Output
M
Flag
3
X
Single bit
BByte (8 bits)
W
Word (16 bits)
D
Double word (32 bits)
4
Address
-
Notes:
Data width
Two examples:
Addressing by word
Addressing by bit
%QW27 (28th word)
%IX1.9 (10th bit in word 2)
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Run-time System CODESYS 2.3
231
Enter the character string of the absolute address without empty spaces. The first
bit of a word has an address of 0.
Pos : 57.6 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/Laufzei tumgebung C ODESYS 2.3Laufz eitumgebung COD ESYS 2.3 - Anl egen von Tas ks @ 16\mod_1375278143139_21.doc x @ 127432 @ 233 @ 1
8.4
Creating Tasks
Set the time response and the priority of individual tasks in the task configuration.
Watchdog
In an application program without task configuration, there is no watchdog that
monitors the cycle time of the application program (PLC_PRG).
Create a task as follows:
1.
Open the task configuration by double-clicking on the “Task configuration”
module in the “Resources” tab.
Figure 73: Task Configuration
2.
To create a task right-click on “Task configuration” and in the contextual
menu select “Attach task”.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
232
Run-time System CODESYS 2.3
3.
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
To assign a new name to the task (e.g. PLC_Prog), click on “New Task”.
Then select the type of task. In this example, this is the “cyclic” type.
Observe the cycle time!
The minimum cycle time for I/O-based tasks is 2 milliseconds (ms)!
Figure 74: Changing Task Names 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
4.
Run-time System CODESYS 2.3
Add the program module PLC_PRG that you have just created (see Section
“Editing the Program Modules”). To do this, right-clock on the “Clock”
symbol and in the contextual menu select “Attach program call-up”. Then,
click the [...] button and [OK].
Figure 75: Call-up to Add to the Program Module
5.
233
Compile the example program by selecting Project > Rebuild all in the
context menu.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
234
Run-time System CODESYS 2.3
8.4.1
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Cyclic Tasks
You can assign a priority for each task in order to establish the task processing
sequence.
Figure 76: Cyclic Task
Order of Task Processing
The priorities given below do not specifiy the order of task processing. The tasks
start in an arbitrary order.
Priority 0 … 5:
Important arithmetic operations and synchronized access to I/O module process
images are to be carried out as tasks with the highest priorities 0 … 5. These tasks
are processed fully according to priority and correspond to Linux® RT priorities
-79 through -74.
Priority 6 … 20:
Real-time access, such as access to ETHERNET and the file system, to fieldbus
data and to the RS-232 interface (when available) are to be carried out as tasks
with average priorities 6 … 20. These tasks are processed fully according to
priority and correspond to Linux® RT priorities -40 through -26.
Priority 21 … 31:
Applications such as long-lasting arithmetic operations and non-real-time-relevant
access to ETHERNET and the file system, to fieldbus data and the RS-232
interface (when provided) are to be carried out as tasks with the lowest priorities
21 … 31. No prioritiy distinction is made between tasks of priorities 21 … 31.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Run-time System CODESYS 2.3
235
These tasks all receive the same computing time from the operating system
(“Completely Fair Scheduler” procedure).
8.4.2
Freewheeling Tasks
So-called freewheeling tasks are not processed in cycles. Their processing
depends solely on the current capacity of the system. The input field “Priority
(0 … 31)” is provided for freewheeling tasks without a function. These tasks are
handled as tasks with priority 21 … 31.
Figure 77: Freewheeling Task
PLC-PRG as Freewheeling Task without Task Configuration
If you do not perform any task configuration, the program PLC_PRG is carried
out with the lowest priority at an interval of 10 ms. The runtime of “freewheeling
tasks” is not monitored by a CODESYS watchdog.
Pos : 57.7 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/Laufzei tumgebung C ODESYS 2.3Laufz eitumgebung COD ESYS 2.3 - Systemer eigniss e @ 16\mod_1375278008058_21.doc x @ 127429 @ 23 @ 1
8.5
System Events
Event tasks can be used in the CODESYS task configuration in addition to
cyclical tasks. Event tasks call up certain events in the device.
To activate events and define a program to be called up, open the window “Task
configuration” in the “Resources” tab in the CODESYS development
environment.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
236
Run-time System CODESYS 2.3
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Figure 78: CODESYS – System Events
Do not set debug points in the event handlers!
Debug points in event handlers can lead to unforeseeable errors and must
therefore not be set!
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Run-time System CODESYS 2.3
237
The following events can be activated:
Table 188: Events
Name
start
stop
before_reset
Description
The event is called directly after the user program starts.
The event is called directly after the user program stops.
The event is called directly before the user program is
reset.
after_reset
The event is called directly after the user program is
reset.
shutdown
The event is called directly before the user program is
shutdown.
excpt_watchdog
The event is called if a task watchdog is recognized.
excpt_access_violation The event is called if a memory access error to an invalid
memory area is recognized. (incorrect pointer, invalid
array index, invalid data descriptor)
excpt_dividebyzero
The event is called if a division by zero is recognized.
after_reading_inputs
The event is triggered after reading all of the inputs
independent of the user program.
before_writing_outputs The event is triggered before writing all of the outputs
independent of the user program.
debug_loop
This event is triggered at every task call, if a breakpoint
was reached in this task and the processing of this task is
therefore blocked.
online_change
This event is called up after initialization of the program
on an online change.
before_download
This event is always called up before a download from
the IDE to the device takes place.
Application stops on a non-defined event handler!
If “excpt” events occur in the system and an event handler has not been defined,
the application goes into the “Stop” status.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
238
Run-time System CODESYS 2.3
8.5.1
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Creating an Event Handler
The example here is provided to illustrate how to define and use an event handler.
The event handler “excpt_dividebyzero” is used in this example.
First, a program is generated in the PLC_PRG- module which provokes division
by 0.
Figure 79: CODESYS Program Provokes Division by “0”
After this, the system event “excpt_dividebyzero” is activated in the Task
Configurator and the name of the event handler to be generated is entered in the
column “Called POU”.
Figure 80: CODESYS – Creating and Activating an Event Handler
To generate the event handler, click [Generate CALLBACK_DIV_BY_ZERO
function block].
A new function having the defined name then appears in the “Function blocks”
tab.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Run-time System CODESYS 2.3
239
Figure 81: CODESYS – New Module has been Generated
Handling for the event that has occurred is now programmed in this new function.
In the example here, the event is documented in a global variable.
Figure 82: CODESYS – Enter the Event in a Global Variable
The newly created project is now supported and can be loaded to the controller.
After startup, the value of the “Events” variable changes only when counter “i”
reaches the value 0, meaning that division by 0 has been performed.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
240
Run-time System CODESYS 2.3
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Figure 83: CODESYS – Variable Contents Prior to Division by “0”
Figure 84: CODESYS – Variable Contents After Division by “0” and Call-up of the Event
Handler
Pos : 57.8 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/Laufzei tumgebung C ODESYS 2.3Laufz eitumgebung COD ESYS 2.3 - Pr oz ess abbilder - Einl eitung @ 14\mod_1361449013042_21.doc x @ 112559 @ 2 @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
8.6
Run-time System CODESYS 2.3
241
Process Images
A process image is a memory area in which the process data is stored in a defined
sequence and consists of the I/O modules attached to the internal bus, the PFC
variables, the bit memory address area and the slaves attached to the fieldbus.
Pos : 57.9 /Serie 750 (WAGO-I/O-SYST EM)/Proz ess abbild Mapping/PFC xxx/750- 8202 Proz ess abbildübersic ht @ 16\mod_1379510024642_21.doc x @ 131833 @ @ 1
Figure 85: Process Image
Pos : 57.10 /Serie 750 ( WAGO-I/O-SYST EM)/Pr ozessabbild M appi ng/PFC xxx/750-82xx Mer kerbereic h @ 16\mod_1379509220906_21.doc x @ 131821 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
242
Run-time System CODESYS 2.3
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Figure 86: Flag Area
Pos : 57.11 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/Laufz eitumgebung COD ESYS 2.3Laufz eitumg ebung COD ESYS 2.3 - Pr ozessabbilder - Kl emmenbus @ 16\mod_1379682262746_21.doc x @ 132375 @ 3 @ 1
8.6.1
Process Images for I/O Modules Connected to the
Controller
After starting the fieldbus controller, it automatically detects all connected I/O
modules.
The analog input and output data is stored first word by word in the process
image. Subsequent to this, come the digital input and output data bits combined to
form words.
The size and structure of the process image for the I/O modules connected to the
system are described in the appendix.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Run-time System CODESYS 2.3
243
I/O Module Data Width
The data width of an I/O module is between 0 and 48 bytes.
I/O Module Process Data
Check the I/O module process data whenever you add or remove the modules
to/from the fieldbus controller. Changing the I/O module topology results in an
adjustment of the process image, as the process data addresses also change.
Pos : 57.12 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/Laufz eitumgebung COD ESYS 2.3Laufz eitumg ebung COD ESYS 2.3 - Pr ozessabbilder - Fel dbus(s e) @ 16\mod_1379682269137_21.doc x @ 132379 @ 3 @ 1
8.6.2
Process Image for Slaves Connected to the Fieldbus
The size and structure of the process image for the slaves connected to the system
are described in the section for the specific fieldbus.
Pos : 57.13 /Serie 750 ( WAGO-I/O-SYST EM)/Pr ozessabbild M appi ng/PFC xxx/Hi nweis : Kei n direkter Z ugriff vom F eldbus auf das Pr ozessabbild der Bus kl emmen! @ 16\mod_1379510128893_21.doc x @ 131836 @ @ 1
No direct access from fieldbus to the process image for I/O modules!
Any data that is required from the I/O module process image must be explicitly
mapped in the CODESYS program to the data in the fieldbus process image and
vice versa! Direct access is not possible!
Pos : 57.14 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/Laufz eitumgebung COD ESYS 2.3Laufz eitumg ebung COD ESYS 2.3 - Zugriff auf Prozes sabbil der I/O - Einl eitung @ 16\mod_1375277533330_21.doc x @ 127423 @ 2 @ 1
8.7
Access to Process Images of the Input and Output
Data via CODESYS 2.3
The following tables describe the possibilities with which you can access the
address ranges of the process image for the inputs and outputs connected to the
internal data bus.
Pos : 57.15 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/Laufz eitumgebung COD ESYS 2.3Laufz eitumg ebung COD ESYS 2.3 - Zugriff auf Prozes sabbil der I/O - Klemmenbus @ 16\mod_1379680080665_21.doc x @ 132363 @ @ 1
Table 189: Access to the Process Images of the Input and Output Data – Internal Data Bus
Memory area
Description
Access via
Logical Address Space
PLC
Internal data bus Map of the local input modules
Read
Word
input process
(internal data bus, I/O module 1
%IW0 to %IW999
image
to 1 bis 64*) in the RAM.
Byte
%IB0 to %IB1999
Internal data bus Map of local output modules
Read/
Word
output process
(internal data bus, I/O module 1 Write
%QW0 to %QW999
image
to 64*) in the RAM.
Byte
%QB0 to %QB1999
* The use of up to 250 I/O modules is possible with the WAGO internal data bus extension
modules.
Pos : 57.16 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/Laufz eitumgebung COD ESYS 2.3Laufz eitumg ebung COD ESYS 2.3 - Zugriff auf Prozes sabbil der I/O - MOD BU S @ 16\mod_1379680078118_21.doc x @ 132359 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
244
Run-time System CODESYS 2.3
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 190: Access to the Process Images of the Input and Output Data – MODBUS
Memory area
Description
Access via
Logical Address Space
PLC
MODBUS input MODBUS input variables,
Read
Word
process image
addressed by word via MODBUS
%IW1000 to %IW1999
Byte
%IB2000 to %IB3999
Read
Bit
MODBUS input variables,
%IX1000.0 …%IX1000.15
addressed by bit via MODBUS
to %IX1384.0 …
%IX1384.15
MODBUS output MODBUS output variables,
Read/
Word
process image
addressed by word via MODBUS Write
%QW1000 to %QW1999
Byte
%QB2000 to %QB3999
MODBUS output variables,
Read/
Bit
addressed by bit via MODBUS
Write
%QX1000.0 …
%QX1000.15 to
%QX1384.0 …
%QX1384.15
Pos : 57.17 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/Laufz eitumgebung COD ESYS 2.3Laufz eitumg ebung COD ESYS 2.3 - Zugriff auf Prozes sabbil der I/O - M er ker @ 16\mod_1379680995981_21.doc x @ 132371 @ @ 1
Table 191: Access to the Process Images of the Input and Output Data – Flags
Memory area
Description
Access via
Logical Address Space
PLC
Flag variables
Total of 128 kB remanent
Read/
%MW0 to
memory (65536 words).
Write
%MW65535
104 kB addressed by word via
Read/
Word (MODBUS)
MODBUS (53248 words)
Write
%MW0 to %MW3327
6.5 kB addressed by bit via
Read/
Bit (MODBUS)
MODBUS (3328 words).
Write
%MX0.0 … %MX0.15 to
%MX3327.0 …
%MX3327.15
Retain variables Retain memory addressed by
Read/
symbols in the NVRAM: 128 kB Write
* The use of up to 250 I/O modules is possible with the WAGO internal data bus extension
modules.
The total size of the memory for flag and retain variables is 128 kB (131060
bytes). The size of these two sections can be customized as required, provided the
total (permissible) size is not exceeded.
If you are using bit-oriented addressing, remember that the basic address is wordbased. The bits are addressed from 0 to 15.
Pos : 57.18 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/Laufz eitumgebung COD ESYS 2.3Laufz eitumg ebung COD ESYS 2.3 - Adres sierungsbeis piel @ 16\mod_1375277668114_21.doc x @ 127426 @ 2 @ 1
8.8
Addressing Example
The following addressing example clarifies the access to the process image:
Table 192: Arrangement of the I/O Modules for the Addressing Example
Fieldbus controller
750400
750554
750402
750504
750454
750650
750468
750600
1
2
3
4
5
6
7
8
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Run-time System CODESYS 2.3
Table 193: Addressing Example
I/O module Input data
Output data
C*
Type
1
%IX8.0
2
%IX8.1
750-400
750-554
750-402
750-504
750-454
1
%QW0
2
%QW1
1
%IX8.2
2
3
4
%IX8.3
%IX8.4
%IX8.5
1
%QX4.0
2
%QX4.1
3
%QX4.2
4
%QX4.3
1
%IW0
2
%IW1
%IW3
%QW2
%QW3
750-468
1
%IW4
2
%IW5
3
%IW6
4
%IW7
Description
2DI, 24 V, 3 ms:
1. Digital input module with a data width of 2
bits. As the analog input modules already
occupy the first 8 words of the input process
image, the 2 bits occupy the lowest-value bits
of the 8th word.
2AO, 4 – 20 mA:
1. Analog output module with a data width of
2 words. This module occupies the first 2
words in the output process image.
4DI, 24 V:
2. Digital input module with a data width of 4
bits. These are added to the 2 bits of the 750400 module and stored in the 8th word of the
input process image.
4DO, 24 V:
1. Digital output module with a data width of
4 bits. As the analog output module already
occupies the first 4 words of the output
process image, the 4 bits occupy the lowestvalue bits of the 4th word.
2AI, 4 – 20 mA:
1. Analog input module with a data width of 2
words. This module occupies the first 2 words
in the input process image.
%IW2
750-650 1
245
750-600
Analog input and output modules
Digital input and output modules
*
C: Number of the input/output
RS-232, C 9600/8/N/1:
The serial interface module is an analog input
and output module, which displays 2 words
both in the input process image and in the
output process image.
4AI, 0 – 10 V S.E:
2. Analog input module with a data width of 4
words. As the 750-454 and 750-650 analog
input and output modules already occupy the
first 4 words of the input process image, the 4
words of this I/O module are added behind the
others.
End module
The passive 750-600 end module does not
transmit any data.
Pos : 57.19 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/Laufz eitumgebung COD ESYS 2.3Laufz eitumg ebung COD ESYS 2.3 - Kl emmenbuss ync hronis ation @ 14\mod_1361449022088_21.doc x @ 112563 @ 23333 @ 1
8.9
Internal Data Bus Synchronization
The internal data bus cycle and the CODESYS task cycle are optimally
automatically synchronized: This depends on the number of I/O modules
connected and the fastest CODESYS task cycle set in the fieldbus controller. The
synchronization cases described below can therefore take place.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
246
Run-time System CODESYS 2.3
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
In this chapter, CODESYS task denotes only tasks within CODESYS that contain
an access to the internal data bus. Tasks that do not access the internal data bus
are not synchronized in the same way as described below. For this, see Section
“Creating Tasks.”
8.9.1
Case 1: CODESYS Task Interval Set Smaller than the I/O
Module Cycle
Execution of the CODESYS tasks is synchronized with internal data bus cycle
time.
The CODESYS task is processed in parallel to the internal data bus cycle. The
CODESYS task interval is extended to the internal data bus cycle time. This is
necessary so that each CODESYS task is started with new input data from the
internal data bus and the output values are also set at the module after each
CODESYS task.
Figure 87: Internal Data Bus Synchronization 01
CTI:
CT:
KBZ:
CODESYS Task Interval
CODESYS Task that accesses the I/O module of the internal data bus
Internal Data Bus Cycle
Example:
CODESYS task interval (CTI): 100 µs
I/O module cycle (KBZ): 2000 µs
Result: Matching of the CODESYS task interval to the I/O module cycle of 2000
µs.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
8.9.2
Run-time System CODESYS 2.3
247
Case 2: CODESYS Task Interval Smaller than Twice the
Internal Data Bus Cycle
Execution of the internal data bus is synchronized with the set CODESYS task
interval.
At the end of the CODESYS task, the internal bus cycle starts, which is processed
synchronously with the fastest CODESYS task. This ensures that when starting
each CODESYS Task, current input data are available from the internal data bus
and the output values of each CODESYS task are also output to the I/O modules.
Figure 88: I/O Module Synchronization 02
CTI: CODESYS Task Interval
CT: CODESYS Task that accesses the I/O module of the internal data bus
KBZ: Internal Data Bus Cycle
Example:
CODESYS task interval (CTI): 2500 µs
Internal data bus cycle (KBZ): 2000 µs
Result: Execution of the internal data bus cycle every 2500 µs.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
248
Run-time System CODESYS 2.3
8.9.3
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Case 3: CODESYS Task Interval Greater than Twice the
Internal Data Buc Cycle
The I/O data from the internal data bus are refreshed once prior to the CODESYS
task and once after the CODESYS task.
Prior to processing the CODESYS task, the internal data bus cycle is executed,
which provides the current input data for the CODESYS task. After execution of
the CODESYS task, an additional internal data bus cycle is started, which
provides the output data to the I/O modules.
This ensures that at the start of every CODESYS task, current input data are
available from the internal data bus and the output data from each CODESYS task
are quickly output to the I/O modules. This prevents processing of internal data
bus cycles that would unnecessarily use a great deal of computing time on the
CPU.
Figure 89: I/O Module Synchronization 03
CTI: CODESYS Task Interval
CT: CODESYS Task that accesses the I/O module of the internal data bus
KBZ: Internal Data Bus Cycle
Example:
CODESYS task interval (CTI): 500 µs
Internal data bus cycle (KBZ): 2000 µs
Result: Execution of the internal data bus cycle 2000 µs prior to the CODESYS
task and once directly after the CODESYS task.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
8.9.4
Run-time System CODESYS 2.3
249
Case 4: CODESYS Task Interval Greater than 10 ms
Synchronization takes place as in case 3; however, the output modules would be
reset to their default state after 150 ms without an internal data bus cycle. This
reliably prevents the execution of an internal data bus cycle after at least every 10
ms.
The I/O data from the internal data bus are refreshed once before the CODESYS
task and once after the CODESYS task and an additional internal data bus cycle is
also executed every 10 ms.
Figure 90: Internal Data Bus Synchronization 04
CTI:
CT:
KBZ:
CODESYS Task Interval
CODESYS task that accesses the I/O module of the internal data bus
Internal data bus cycle
Example:
CODESYS task interval (CTI): 150000 µs
Internal data bus cycle (KBZ): 2000 µs
Result: Execution of the internal data bus cycle 2000 µs prior to the CODESYS
task, once directly after the CODESYS task and 10 ms after the previous internal
data bus cycle.
Pos : 57.20 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/Laufz eitumgebung COD ESYS 2.3Laufz eitumg ebung COD ESYS 2.3 - Kl emmenbus konfiguration @ 16\mod_1376652765349_21.doc x @ 129171 @ 3455 @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
250
Run-time System CODESYS 2.3
8.9.5
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Internal Data Bus Configuration
Figure 91: Internal Data Bus Settings
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Run-time System CODESYS 2.3
251
Table 194: Internal Data Bus Settings
Parameter
Explanation
The Update mode is used to configure how the internal data bus
process data is to be updated (refreshed).
In the asynchronous update mode process data are
Asynchronous
Update Mode
refreshed in cycles at a definable interval.
In the synchronous update mode the process data
*
Synchronous are synchronized with the most rapid CODESYS
task that accesses the internal data bus.
The update interval for the internal data bus is set by the cycle
Internal Data time. This setting is effective only in the asynchronous mode.
1000 µs
Minimum value 1 millisecond
Bus Cycle
*
Time
10000 µs
Default value 10 milliseconds
50000 µs
Maximum value 50 milliseconds
This value indicates the priority for the internal data bus thread.
This setting is effective only in the asynchronous mode.
Internal Data This priority is equivalent to the priority of the cyclic CODESYS
tasks (see Section “Cyclic Tasks”).
Bus Thread
This setting is effective only in the asynchronous mode.
Priority
0*
Highest priority
15
Lowest priority
PLC stop
Specifies the response of the internal data bus outputs when the
response
PLC application stops.
Hold last
The output states are retained.
value
Set to zero*
Outputs are set to zero.
*
Default setting
8.9.5.1
Effect of Update Mode on CODESYS Tasks
8.9.5.1.1 Asynchronous Update Mode
In the asynchronous update mode there is no direct influence on CODESYS task
behavior.
Internal data bus “freeze” on priority conflicts!
In the asynchronous update mode there is a risk of the internal data bus
“freezing”, as the internal data bus thread operates at the same priority as the IEC
tasks. The internal data bus thread must therefore use a priority higher than that
of the IEC task to prevent this from occurring.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
252
Run-time System CODESYS 2.3
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
8.9.5.1.2 Synchronous Update Mode
In the synchronous update mode the runtime behavior of CODESYS tasks can be
influenced by the internal data bus. The minimum task interval that can then be
achieved depends on the duration of an internal data bus cycle. The duration of an
internal data bus cycle, on the other hand, is based on the I/O modules connected
to the bus. As a rule of thumb: The shorter the internal data bus structure, the
shorter the cycle time and digital modules are faster than analog or complex ones.
In the event of an internal data bus error, the CODESYS tasks are blocked until
the error is rectified, i.e., when an internal data bus cycle has been successfully
executed again.
No call-up of internal data bus status when internal data bus errors are
present!
If an internal data bus error has occurred, it is not possible to call up the internal
data bus status using KBUS_ERROR_INFORMATION (mod_com.lib) while in
the synchronous update mode.
Pos : 57.21 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/Laufz eitumgebung COD ESYS 2.3Laufz eitumg ebung COD ESYS 2.3 - Speic herei nstellungen @ 16\mod_1376030901877_21.doc x @ 128313 @ 2333 @ 1
8.10
Memory Settings in CODESYS
The list below illustrates the standard memory allocation of the PFC200:
•
•
•
•
•
•
•
8.10.1
Program memory:
16 Mbyte (max.)
Data memory:
64 Mbytes
Input data:
64 kbytes
Output data:
64 kbytes
Flags:
24 kbytes
Retain:
104 kbytes
Function block limitation: 12 * 4096 bytes = 48 kbytes
Program Memory
The program memory (also code memory) cannot be configured and is limited to
a maximum of 16 Mbytes. The memory space actually available is based on the
scope of installed applications.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Run-time System CODESYS 2.3
253
Figure 92: Program Memory
8.10.2
Data Memory and Function Block Limitation
The data memory is set for 64 Mbytes in the controller's initial state.
This set value has already been requested in the system after a successful program
download and can be fully utilized.
Together with the data memory to be used by the application, memory is required
for the individual program function blocks in the system.
The size of the administration space is calculated from the function block
limitation * 12 (i.e., normally 4096 * 12).
The actual size of the main memory required in the system for data is the sum of
global data memory and function block limitation memory.
This value should not exceed the value specified for “Size of entire data memory.”
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
254
Run-time System CODESYS 2.3
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Figure 93: Data Memory and Function Block Limitation
8.10.3
Remanent Memory
A total of 128 kbytes of remanent memory is available for the IEC-61131
application.
The remanent section is subdivided into the flag area (memory) and the retain
area.
Figure 94: Remanent Main Memory
The breakdown of the flag and retain variables can be customized as required.
Observe general conditions!
The sum of Memory + Retain must not exceed the maximum value of 128 kbytes
(0x20000).
A maximum of 10,000 retain variables can be created.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Run-time System CODESYS 2.3
255
Figure 95: Flag and Retain Memory
Pos : 57.22 /Serie 750 ( WAGO-I/O-SYST EM)/In Betri eb nehmen/Laufz eitumgebung COD ESYS 2.3Laufz eitumg ebung COD ESYS 2.3 - Vis ualisi erung @ 14\mod_1361449465183_21.doc x @ 112571 @ 2333 @ 1
</dg_
8.11
CODESYS Visualization
CODESYS Web visualization is based on Java technology. All Java programs
require a Java runtime environment (JRE), which must be installed on the host PC
along with an Internet browser. An applet is stored in the file system of a Web
server and is accessible to browsers via an HTML page.
You create all visualization types (HMI and Web visualization) with the same
CODESYS graphic editor. Select the visualization type in the “Target system
settings” window. A description file in XML format is generated from the
information for each of these pages. You can find these files in the subfolder
“visu” of the CODESYS installation path. The HTML home page “webvisu.htm”
and the Java archive “webvisu.jar” in the applet (webvisu.class) are also saved
there in a compressed format.
Once you have selected a visualization type, the following steps must be
performed to execute the technique:
1.
Click the “Resources” tab and open the “Target system settings.” Specify
whether you wish to have visualization displayed as a “Web visualization”
using an Internet browser.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
256
Run-time System CODESYS 2.3
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Figure 96: Selecting the Visualization Technique in the Target System Settings
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
2.
Run-time System CODESYS 2.3
257
Generate a start page for the visualization. Right-click the “Visualization”
folder in the “Visualization” tab. Select Add object ... from the contextual
menu. The “New visualization” dialog box opens.
Figure 97: Creating the PLC_VISU Starting Visualization
3.
In the “New visualization” dialog window, enter the name PLC_VISU for
the start visualization. This page is then displayed as the start page upon
system startup.
4.
Activate the CODESYS Web server in the WBM on the “Ports and Services
– CODESYS Services” page in the “CODESYS Webserver” group.
5.
Activate the http service in the WBM on the “Ports and Services – Network
Services” page in the “HTTP” group.
If you transfer the PLC program to the controller (Online > Login) and start the
program (Online > Start), enter one of the following lines in the address line of
the Web browser for online visualization:
-
“https://<IP address of the controller>/webvisu”, preferred method (http can
also be used instead of https)
-
“https://<IP address of the controller>”, if the default Web server in the
WBM has been set to“WebVisu” (http can also be used instead of https)
-
“http://<IP address of the controller>:8080/webvisu.htm”
You can also have Web visualization displayed via the WBM (see Section
“`CODESYS - WebVisu´” Page).
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
258
Run-time System CODESYS 2.3
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Frequently Asked Questions
Additional information (FAQs) on CODESYS Web visualization is also provided
in the Section “Frequently Asked Questions about CODESYS Web
Visualization” and in the online Help function for CODESYS 2.3.
8.11.1
Limits of CODESYS Visualization
The controller supports the “WebVisu” visualization type integrated into
CODESYS. Technological limitations can be caused by the visualization type
used.
Compared to “HMI”, Web visualization on the controller is performed within
significantly narrower physical limits. Whereas “HMI” can access almost
unlimited resources on a desktop PC, the following limitations must be observed
when using Web visualization:
Adapting to the File System
The overall size of the PLC program, visualization files, bitmaps, log files,
configuration files, etc. must fit into the file system.
Process Data Memory
Web visualization uses its own protocol for exchanging process data between
applet and control.
The controller transfers process data with ASCII coding. The pipe symbol (“|”) is
used to separate two process values. Therefore, the space requirement for a
process data variable in the process data memory is dependent not only on the
data type, but also on the process value itself. Thus, a variable of the “WORD”
type occupies between one byte for the values 0 through 9 and five bytes for
values from 10000 and greater. The selected format (ASCII + |) only permits a
rough estimate of the space requirement for the individual process data in the
process data buffer. If the size of the ASCII coded process data is exceeded, Web
visualization no longer works as expected.
Computer Performance/Processor Time
The controller is based on a real-time operating system. This means that highpriority processes (e.g., PLC program) interrupt or block lower priority processes.
The Web server responsible for Web visualization is among these lower priority
processes.
Processor Time
Make sure when configuring tasks, that there is sufficient processor time available
for all processes.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Run-time System CODESYS 2.3
259
Network Load
The controller's CPU processes both the PLC program and network traffic.
ETHERNET communication demands that each received telegram is processed,
regardless of whether it is intended for the controller or not.
A significant reduction of the network load can be achieved by using switches
instead of hubs.
There is no measure against broadcast telegrams that can be used on the
controller, however. These can only be curtailed by the sender, or blocked with
configurable switches that have a broadcast limitation. A network monitor such as
“wireshark” (www.wireshark.com) provides an overview of the current load in
your network.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
260
Run-time System CODESYS 2.3
8.11.2
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Eliminating Errors in CODESYS Web Visualization
If you are experiencing problems when working with the CODESYS Web
visualization, use the following table to find the solution. If you cannot eliminate
the problem, please contact WAGO support.
Table 195: Errors and Remedies
Error
Solution
Internet Explorer
Close all Internet Explorer windows and restart. If the error persists, this
reports the error
indicates a missing or damaged file.
“APPLET NOT
Using FTP, check if the entire Java archive “webvisu.jar” is available in
INITIATED”
the “/PLC” folder of the controller. The original file can be found in the
installation path of CODESYS (usually under C:\Programme\WAGO
Software\CODESYS V2.3\Visu\webvisu.jar).
If necessary, replace the damaged file using FTP or force the download
of all files in CODESYS with Purge All > Compile All > Log in.
Web visualization is not Have you installed the JRE? Check the firewall settings, e.g., if port
displayed
8080 is open.
Web visualization
The call-up intervals selected in the task configuration are too small. As
“freezes”.
a result, the Web server of the controller — which is executed with a
Web visualization stops low priority — does not receive sufficient computer time, if any at all.
after an extended period
of time.
If no (explicit) task configuration has been provided, the PLC_PRG is
(implicitly) executed as a free running task with Priority 1. This
significantly limits the Web server’s computing time. Always provide a
task configuration when using Web visualization. In doing so, the callup interval should not exceed three times the average execution time.
When determining the execution time, ensure that the PLC program has
reached a “steady state.” When determining the execution time, ensure
that the PLC program is not “steady state.”
Web visualization
Not all files may fit into the controller's file system. Delete any
cannot be loaded into
unneeded data (e.g., via FTP).
the controller
Bitmap is not displayed If the name of an image file contains umlauts, the Web server cannot
interpret these image names.
Java console reports:
The JRE does not find the entry point for the class “webvisu.class” in
“Class not found”
the Java archive “WebVisu.jar”. The Java archive is probably
incomplete. Delete “WebVisu.jar” from the Java cache and/or deactivate
the cache. In this case, the controller requests the archive (applet) again.
If the problem persists, reload the project into the controller.
Web visualization is
Process data communication has failed.
static, all process values If Web visualization is operated over a proxy server, then a SOCKS
are “0”
proxy is also necessary for process data exchange in addition to the
actual HTTP proxy.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
8.11.3
Run-time System CODESYS 2.3
261
FAQs about CODESYS Web Visualization
How can I optimize the applet for special screen resolutions?
In order to optimize the Web visualization for display on a device with a fixed
resolution, proceed as follows:
In the “Target system settings”, enter the pixel width and height in the tab
“Visualization”. When the visualization is created, the visible area is highlighted
in gray. However, the actual pixel width and height of the Web visualization is
defined by the attributes “Height” and “Width” of the HTML APPLET tag in the
“webvisu.htm” file. Do not forget to also adapt these parameters to the existing
resolution.
Which JRE should I use?
Java2 standard edition Version 1.5.0 (J2SE1.5.0_06) or higher is recommended.
This is available free of charge at www.oracle.com.
Microsoft's MSJVM3810 was also tested. For PDAs, there are runtime
environments available from other manufacturers (JamaicaVM, CrEme, etc.).
Please consider that for the Web visualization, these solutions can behave
differently within their scope of services (e.g., stability) than those mentioned
above.
Should the Java Cache be used?
This depends on the situation. After a standard installation, the cache is enabled. If
the cache is enabled, the JRE uses it to store applets and Java archives. If the Web
visualization is called up a second time, it requires considerably less time to start
because the applet (approx. 250 kb) does not need to be reloaded via the network,
but is already available in the cache. This is especially useful when network
connections are slow.
Note:
The Java archives may not be completely transferred into the cache due to
network failures. In this case, the cache must be cleared manually or disabled.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
262
Run-time System CODESYS 2.3
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Why does the visualization element “TREND” in the Web visualization only
work “Online”?
The following settings must be selected for visualization projects: Resources tab
> Target system settings.
Activate “Web visualization” and “Trend data recording within control”.
Otherwise, the trend data is stored on the hard drive of the CODESYS
development PC. This makes a permanent connection between the controller and
the CODESYS gateway necessary. If this connection is interrupted, this may lead
to the controller behaving unpredictably.
In the TREND configuration dialog, you can choose between “Online” and
“History” operating modes. The controller only supports the “Online” operating
mode for visualization projects since it is not possible to configure the maximum
size (quota) of the trend files (*.trd). Uncontrolled expansion of trend files can
lead to unpredictable controller behavior.
In most cases, the use of the “HISTOGRAM” visualization element is the better
choice, as this gives full control over the time and number of measurements and
thus the amount of memory required.
What needs to be observed when the visualization element “ALARM
TABLE” is used in the Web visualization?
The status of this component is best described as “Add-On”, i.e., an extra that is
free of charge and not warrantied.
The following settings must be selected for visualization projects: Resources tab
> Target system settings.
Activate “Web visualization” (checkmark) and “Alarm handling within control”.
Otherwise, the alarm data is processed on the CODESYS development PC. This
makes a permanent connection between the controller and the CODESYS
gateway necessary. If this connection is interrupted, this may lead to the controller
behaving unpredictably.
Pos : 58 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
e!RUNTIME Runtime Environment
Pos : 59 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 1/Laufz eitumg ebung e!RUNTIME - Übersc hrift 1 @ 18\mod_1390204344577_21.doc x @ 142328 @ 1 @ 1
9
e!RUNTIME Runtime Environment
Pos : 60.1 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/Laufzei tumgebung e!RUNTIME/Laufz eitumg ebung e!RUNTIME - Gr undleg ende Hinweis e @ 21\mod_1417616245337_21.doc x @ 169916 @ 2 @ 1
9.1
General Notes
Additional Information
Information on the installation and startup of e!COCKPIT is provided in the
corresponding manual.
Information on programming is provided in the CODESYS 3 documentation.
Pos : 60.2 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
263
264
e!RUNTIME Runtime Environment
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 60.3 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/Laufzei tumgebung e!RUNTIME/Laufz eitumg ebung e!RUNTIME - Pri oritäten @ 21\mod_1417612405857_21.doc x @ 169899 @ 2 @ 1
9.2
CODESYS V3 Priorities
A list of priorities implemented for the controller is provided below as
supplementary information to the CODESYS 3 documentation.
Table 196: CODESYS V3 Priorities
Scheduler
Task
Local or
fieldbus - HIGH
Linux®
Priority
IEC
Priority
-95 … -86
Internal data bus (-88)
Mode selector
-85
switch monitoring
CODESYS
watchdog
Preemptive
scheduling
Real-time
range
-83
Cyclic and event-55 … -53 1 … 3
controlled IEC task
Local or
fieldbus - MID
-52 … -43
Cyclic and event-42 … -32 4 … 14
controlled IEC task
Local or fieldbus –
-13 … -4
LOW
Fair
scheduling
None realtime range
CODESYS
communication
Cyclic, eventcontrolled and
freewheeling IEC
task
Background
(20)
Remark
Task registers changes
to the mode selector
switch and changes the
state of the PLC
application. (start, stop,
reset warm/cold)
Execution of the
watchdog functions
For real-time tasks
which must not be
influenced in execution
by external interfaces
(e.g., fieldbus).
CAN (-52 … -51)
Profibus (-49 … 45)
MODBUS slave/master
(-43)
For real-time tasks
which must not
influence fieldbus
communication during
execution.
Communication with
the CODESYS
development
environment
15
Incl. standard priority
of the visualization task
Pos : 60.4 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
e!RUNTIME Runtime Environment
265
Pos : 60.5 /Serie 750 (WAGO-I/O-SYST EM)/In Betrieb nehmen/Laufzei tumgebung e!RUNTIME/Laufz eitumg ebung e!RUNTIME - Speicherei nstellungen @ 21\mod_1417616185610_21.doc x @ 169902 @ 2333 @ 1
9.3
Memory Spaces under e!RUNTIME
The memory spaces in the controller under e!RUNTIME have the following sizes:
•
•
•
•
•
•
9.3.1
Program and data memory:
Input data:
Output data:
Flags:
Retain:
Function block limitation:
60 Mbytes
64 kbytes
64 kbytes
24 kbytes
104 kbytes
12 * 4096 bytes = 48 kbytes
Program and Data Memory
The program (also code) and data memory has a size of 60 Mbytes.
This space has already been requested in the system after a successful program
download and can be fully utilized.
The memory space is dynamically divided up into program and data space.
9.3.2
Function Block Limitation
Together with the data memory to be used by the application, memory is required
for the individual program function blocks in the system.
The size of the administration space is calculated from the function block
limitation * 12 (i.e., 4096 * 12).
The actual size of the main memory required in the system for data is the sum of
global program and data memory and function block limitation memory.
9.3.3
Remanent Memory
A total of 128 kbytes of remanent memory is available for the IEC-61131
application.
The remanent section is subdivided into the flag area (memory) and the retain
area.
Figure 98: Remanent Main Memory
Pos : 61 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
266
MODBUS – CODESYS 2
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 62 /Serie 750 ( WAGO-I/O-SYST EM)/F eldbus kommuni kation/PFC/MODBU S/MOD BU S - COD ESYS 2 - Ü bersc hrift 1 @ 18\mod_1392197250592_21.doc x @ 145253 @ 1 @ 1
10
MODBUS – CODESYS 2
Pos : 63.1 /Serie 750 (WAGO-I/O-SYST EM)/F eldbus kommuni kation/PFC/MOD BU S/MOD BUS 750-82xx - Allgemein, Features, Konfig urati on, Eins tellungen TC P, Ei nstellungen UD P @ 14\mod_1363102272477_21.doc x @ 114280 @ 222333 @ 1
</dg_
10.1
General
MODBUS is a non-vendor-specific, open fieldbus standard for a wide range of
applications in production and process automation. The MODBUS
communications protocol is based on a master/slave or client/server architecture
that uses function codes for execution of individual MODBUS services, which
have reading or writing access to individual or multiple elements of the MODBUS
data model simultaneously.
10.2
Features
The MODBUS slave implemented in the PFC200 has the following features:
•
3 modes: MODBUS TCP, MODBUS UDP and MODBUS RTU, which can
be run independently of one another simultaneously
•
Each mode can be configured
•
10 supported MODBUS services (Function Codes): FC1 to FC6, FC15,
FC16, FC22, FC23
•
Data exchange via 1000 registers in each of the local MODBUS process
images
•
768-byte sector that can be addressed by bits in each local MODBUS
process image
•
Access to a 104 kB flag sector (total of 53248 registers/words, with 3328
addressable bits)
•
28 Information and configuration registers
•
Up to 1000 TCP connections
•
MODBUS communications monitoring using programmable watchdogs
•
Configurable response on PLC stop
•
Configurable response on disruption of MODBUS communication
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
10.3
MODBUS – CODESYS 2
267
Configuration
All of the MODBUS operating modes are configured using the CODESYS PLC
configuration.
Figure 99: CODESYS PLC Configuration - MODBUS Settings
The MODBUS slave configuration is composed of four basic parameter groups:
•
MODBUS settings,
•
MODBUS TCP settings,
•
MODBUS UDP settings,
•
MODBUS RTU settings.
A detailed description of all the parameter groups is given in the following
sections.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
268
MODBUS – CODESYS 2
10.3.1
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
MODBUS Settings
The “MODBUS settings” group contains the following configuration parameters.
Table 197: MODBUS Settings
Parameters
PLC stop
behavior
Explanation
Response of the MODBUS slave when the controller has halted
(controller in STOP state)
No data
No data exchange possible. MODBUS requests
exchange
will always be answered by the exception
response “ILLEGAL FUNCTION” (0x81).
Switch to
Data exchange possible. Substitute values (0) are
substitute
provided for MODBUS read requests and the
value*
values accepted unchanged in the local MODBUS
process image for write requests, without passing
these on to the controller.
Hold last
Data exchange possible. The last frozen values
value
are provided for MODBUS read requests and the
values accepted unchanged in the MODBUS
process image for write requests, without passing
these on to the controller.
Fieldbus error Response of the MODBUS slave to detected fieldbus errors
response
(interruption of communication).
No data
No data exchange possible.
exchange
Switch to
Data exchange possible. Substitute values (0) are
substitute
supplied from the MODBUS process image for
value*
PLC read functions; for write access the values
are accepted unchanged in the MODBUS process
image without passing them on to the MODBUS
master.
Hold last
Data exchange possible. The previously frozen
value
values are supplied from the MODBUS process
image for PLC read functions; for write access the
values are accepted unchanged in the MODBUS
process image without passing them on to the
MODBUS master.
*
Default setting
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
10.3.2
MODBUS – CODESYS 2
269
MODBUS TCP Settings
The “MODBUS TCP Settings” contains the following configuration parameters
for the “MODBUS TCP” mode:
Table 198: MODBUS TCP Settings
Parameters
TCP mode
Explanation
Enable for the MODBUS TCP mode
Off
Operation not permitted
*
Active
Operation possible
TCP port
Port number for the TCP link
1
Minimum port number
*
502
MODBUS default port
65535
Maximum port number
TCP Timeout Time-out for a TCP link
1
100 ms (1 × 100 ms)
*
600
60 seconds (600 × 100ms)
65535
1 h 49 min 13 s 500 ms (65535 × 100 ms)
*
Default setting
10.3.3
MODBUS UDP Settings
The “MODBUS UDP Settings” group contains the following configuration
parameters for the “MODBUS UDP” mode:
Table 199: MODBUS UDP Settings
Parameters
UDP mode
Explanation
Enable for the MODBUS UDP mode
Off
Operation not permitted
*
Active
Operation possible
UDP port
Port number for the UDP link
1
Minimum port number
502*
MODBUS default port
65535
Maximum port number
*
Default setting
Pos : 63.2 /Serie 750 (WAGO-I/O-SYST EM)/F eldbus kommuni kation/PFC/MOD BU S/MOD BUS 750-82xx - Ei nstellungen RTU @ 17\mod_1383212257891_21.doc x @ 136368 @ 3 @ 1
10.3.4
MODBUS RTU Settings
The “MODBUS RTU Settings” group contains the following configuration
parameters for the “MODBUS RTU” mode:
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
270
MODBUS – CODESYS 2
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 200: MODBUS RTU Settings
Parameters
RTU mode
Explanation
Enable for the MODBUS RTU mode
Off*
Operation not permitted
Active
Operation possible
Device ID
Device ID (device address) for the tty device
1*
min. device ID
247
max. device ID
Maximum
Response timeout for a request in [ms]
response time 2000
min. response time = 2 seconds. If this value is set
lower than 2 seconds, it will be corrected
internally to 2 seconds.
*
5000
Default = 5 seconds
4294967295
max. response time > 71 hours.
Interface
Device name
“dev/…”
Name of the tty in the string
*
“dev/ttyO0”
Standard tty
Baud rate
Communication baud rate
1200 baud
1200 baud min. transmission speed
2400 baud
2400 baud
4800 baud
4800 baud
9600 baud
9600 baud
19200 baud
19200 baud
38400 baud
38400 baud
57600 baud
57600 baud
*
115200 baud 115200 baud, max. transmission speed
Stop bits
Number of stop bits
1 stop bit*
1 stop bit in the frame; must be used when even
or odd parity has been selected.
2 stop bits
2 stop bits in the frame; must be used when
“None” has been selected for parity.
Parity
Parity check
None
No parity check performed; 2 stop bits must be
selected in the configuration for this setting.
*
Even
Even parity
Odd
Odd parity
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
MODBUS – CODESYS 2
271
Table 200: MODBUS RTU Settings
Parameters
Flow control
Explanation
Data flow control (Supported only for the setting “RS-232” for the
physical interface.)
None*
No data flow control
RTS/CTS
Hardware flow control
Physical
Mode for the physical interface
interface
RS-232*
RS-232 is used as the physical interface.
RS-485
RS-485 is used as the physical interface.
*
Default setting
Pos : 63.3 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
272
MODBUS – CODESYS 2
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 63.4 /Serie 750 (WAGO-I/O-SYST EM)/F eldbus kommuni kation/PFC/MOD BU S/MOD BUS 750-82xx - Datenaustausc h @ 17\mod_1383212266219_21.doc x @ 136372 @ 233334444 @ 1
</dg_
10.4
Data Exchange
MODBUS data exchange is performed in cycles or acyclically using MODBUS
services. The type and number of usable MODBUS services depends on the area
that is addressed. There are generally four MODBUS-relevant address areas in the
PFC200:
•
MODBUS input process image (MODBUS Input) – is an area in the PIO
(PIO = Output Process Image), in which data from the PLC is provided in
cycles exclusively for MODBUS Read services.
•
MODBUS output process image (MODBUS Output) – is an area in the PII
(PII = Input Process Image), in which MODBUS Write services provide
data for cyclic reading by the PLC. MODBUS Read services are also
acceptable in this area.
•
MODBUS flag area – is an area, in which both MODBUS Read and Write
services can be executed.
•
MODBUS register – is an area, in which the WAGO-specific information
and configuration registers are contained. Only MODBUS register services
may be executed in this area.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
10.4.1
MODBUS – CODESYS 2
273
Process Image
The main data interfaces between the PLC and the MODBUS slave are the local
MODBUS process images in the PLC address area based on IEC 61131. The
MODBUS input process image (MODBUS Input) is in the PIO and the MODBUS
output process image (MODBUS Output) in the PII. Data memory blocks of 2 kB
(1000 registers/word) are available for each local MODBUS input and output
process image. The first 768 bytes of each of these data blocks are also provided
for executing bit services.
Figure 100: MODBUS Process Image
As no direct access to the I/O modules is provided by the fieldbus, data can be
exchanged via this interface between the PLC and MODBUS for processing in the
control system (PLC). Using this data in the individual I/O modules connected to
the PLC can then be performed by the application.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
274
MODBUS – CODESYS 2
10.4.2
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Flag Area
MODBUS can also exchange data and fieldbus variables with the PLC via the
flag area. Caution is urged, however, when using data and/or variables in this area
that is accessed by both MODBUS and the PLC. This “conflicting” access is not
protected from either side and could result in data inconsistency.
Figure 101: Flag Area
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
10.4.3
MODBUS – CODESYS 2
275
MODBUS Registers
WAGO-specific registers are implemented in the last MODBUS-relevant address
area; this simplifies the reading of certain system and MODBUS information, as
well as configuration.
The MODBUS address area reserved for these registers ranging from the
MODBUS starting address of 4096 (0x1000) up to the MODBUS end address of
12287 (0x2FFF), without any allocation to the IEC 61131 address area. These
registers can be queried using the register read services FC3, FC4 and FC23 and
with the register write services FC6, FC16 and FC23. A detailed description of the
individual registers is given in the section “WAGO MODBUS Registers”.
10.4.4
MODBUS Mapping
10.4.4.1
MODBUS Mapping for Write Bit Services FC1, FC2
The table below outlines the mapping for the MODBUS-reading, bit-oriented
services:
•
FC1 – Read Single Coil,
•
FC2 – Read Discrete Inputs.
Table 201: MODBUS Mapping for Read Bit Services FC1, FC2
MODBUS Address
(hexadecimal values
in parentheses)
0 … 6143
(0x0000 … 0x17FF)
6144 … 12287
(0x1800 … 0x2FFF)
12288 … 65535
(0x3000 … 0xFFFF)
IEC 61131
Address
%IX1000.0 …
%IX1383.15
Description
MODBUS Output:
6144 PFC input bit variables in the first
384 registers/words (768 bytes) of the
2kB MODBUS output process image in
the PII.
Note: In this area, the read bit services
return the content from the bit-addressed
PII.
%QX1000.0 … MODBUS Input:
%QX1383.15
6144 PFC output bit variables in the first
384 registers/words (768 bytes) of the 2
kB MODBUS-input process image in the
PIO.
%MX0.0 …
Flag area:
%MX3327.15 53248 bit flags (6.5 kB) in the bitaddressed flag area
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
276
MODBUS – CODESYS 2
10.4.4.2
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
MODBUS Mapping for Write Bit Services FC5, FC15
The table below outlines the mapping for the MODBUS-writing, bit-oriented
services:
•
FC5 – Write Single Coil
•
FC15 – Write Multiple Coils
Table 202: MODBUS Mapping for Write Bit Services FC5, FC15
MODBUS Address
(hexadecimal values
in parentheses)
0 … 6143
(0x0000 … 0x17FF)
6144 … 12287
(0x1800 … 0x2FFF)
12288 … 65535
(0x3000 … 0xFFFF)
IEC 61131
Address
Description
%IX1000.0 …
%IX1383.15
MODBUS Output:
6144 PFC input bit variables in the first
384 registers/words (768 bytes) of the
2kB MODBUS output process image in
the PII.
%QX1000.0 … MODBUS Output:
%QX1383.15
MODBUS-only area for bit-oriented
write access.
Bit-based write services for this area are
acknowledged by the MODBUS slave
with the MODBUS exception code
“ILLEGAL DATA ADDRESS” (0x02).
%MX0.0 …
Flag area:
%MX3327.15 53248 bit flags (6.5 kB) in the bitaddressed flag area
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
10.4.4.3
MODBUS – CODESYS 2
277
MODBUS Mapping for Read Register Services FC3, FC4, FC23
The table below outlines the mapping for the MODBUS-reading, register-oriented
services:
•
FC3 – Read Holding Registers,
•
FC4 – Read Input Registers,
•
FC23 – Read/Write Multiple Registers
Table 203: MODBUS Mapping for Read Register Services FC3, FC4, FC23
MODBUS Address
(hexadecimal values
in parentheses)
0 … 999
(0x0000 … 0x03E7)
IEC 61131
Address
Description
%IW1000 …
%IW1999
MODBUS Output:
1000 PFC input registers/words in the
2 kB MODBUS output process image in
the PII.
Note: In this area, the read register
services return the content from the PII.
MODBUS Input:
1000 PFC output registers/words in the
2 kB MODBUS input process image in
the PIO.
Note on FC23:
Only the Read portion of this service can
be executed.
Inhibited to MODBUS-only area for
register-oriented read access. Registerbased read services for this area are
acknowledged by the MODBUS slave
with the MODBUS exception code
“ILLEGAL DATA ADDRESS” (0x02).
Information and configuration registers:
Not all MODBUS addresses in this range
are valid.
Valid MODBUS addresses are described
in the Section “WAGO MODBUS
Registers”.
Access to invalid addresses are
acknowledged by the MODBUS slave
with the MODBUS exception code
“ILLEGAL DATA ADDRESS” (0x02).
Note on FC23:
The Write portion of this service can
only be executed for registers that data
can be written to.
1000 … 1999
%QW1000 …
(0x03E8 … 0x07CF) %QW1999
2000 … 4095
(0x07D0 … 0x0FFF)
4096 … 12287
(0x1000 … 0x2FFF)
No IEC 61131
address
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
278
MODBUS – CODESYS 2
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 203: MODBUS Mapping for Read Register Services FC3, FC4, FC23
MODBUS Address
(hexadecimal values
in parentheses)
12288 … 65535
(0x3000 … 0xFFFF)
IEC 61131
Address
Description
%MW0 …
%MW53247
Flag Area:
53248 register/word flags (104 kB) in the
flag area
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
10.4.4.4
MODBUS – CODESYS 2
279
MODBUS Mapping for Write Register Services FC6, FC16, FC22, FC23
The table below outlines the mapping for MODBUS-writing, register-oriented
services.
•
FC6 – Write Single Register,
•
FC16 – Write Multiple Registers,
•
FC22 – Mask Write Register, not for information and configuration registers
•
FC23 – Read/Write Multiple Registers.
Table 204: MODBUS Mapping for Write Register Services FC6, FC16, FC22, FC23
MODBUS Address
(hexadecimal values
in parentheses)
0 … 999
(0x0000 … 0x03E7)
IEC 61131
Address
Description
%IW1000 …
%IW1999
1000 … 1999
No access to:
(0x03E8 … 0x07CF) %QW1000 …
%QW1999
MODBUS Output:
1000 PFC input registers/words in the
2 kB MODBUS output process image in
the PII.
MODBUS Output:
Inhibited MODBUS area for registeroriented write access.
2000 … 4095
(0x07D0 … 0x0FFF)
Register-oriented write services in this
area are acknowledged by the MODBUS
slave with the MODBUS exception code
“ILLEGAL DATA ADDRESS” (0x02).
Inhibited MODBUS area for registeroriented write access.
4096 … 12287
(0x1000 … 0x2FFF)
No IEC 61131
address
FC6, FC16, FC23
only,
not FC22
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Register-oriented write services in this
area are acknowledged by the MODBUS
slave with the MODBUS exception code
“ILLEGAL DATA ADDRESS” (0x02).
Information and Configuration Registers:
Not all MODBUS addresses in this area
are valid and not all registers can be
written to.
Valid MODBUS addresses are described
in the Section “WAGO MODBUS
Registers”.
Access to invalid addresses are
acknowledged by the MODBUS slave
with the MODBUS exception code
“ILLEGAL DATA ADDRESS” (0x02).
280
MODBUS – CODESYS 2
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 204: MODBUS Mapping for Write Register Services FC6, FC16, FC22, FC23
MODBUS Address
(hexadecimal values
in parentheses)
12288 … 65535
(0x3000 … 0xFFFF)
IEC 61131
Address
Description
%MW0 …
%MW53247
Flag Area:
53248 register/word flags (104 kB) in the
flag area
Pos : 63.5 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
MODBUS – CODESYS 2
281
Pos : 63.6 /Serie 750 (WAGO-I/O-SYST EM)/F eldbus kommuni kation/PFC/MOD BU S/MOD BUS 750-82xx - WAGO-MOD BUS-R egister, COD ESYS 2, <= F W06 @ 26\mod_1465365445008_21.doc x @ 211980 @ 23444434444433444433444444 @ 1
10.5
WAGO MODBUS Register
System and MODBUS data can be read and some MODBUS parameters
configured using the WAGO MODBUS registers. The following table lists all of
the WAGO MODBUS registers.
Table 205: WAGO MODBUS Registers
MODBUS Address Data Length
Access Description
in Words
Dec.
Hex.
4130
0x1022
1
ro
Number of registers in the
MODBUS input process image in
the PIO
4131
0x1023
1
ro
Number of registers in the
MODBUS output process image
in the PII
4132
0x1024
1
ro
Number of bits in the MODBUS
input process image in the PIO
4133
0x1025
1
ro
Number of bits in the MODBUS
output process image in the PII
4136
0x1028
1
ro
4138
0x102A
1
ro
4144
0x1030
1
r/w
4145
0x1031
3
ro
4151
4160
0x1037
0x1040
1
1
r/w
ro
4352
4353
4354
0x1100
0x1101
0x1102
1
1
1
wo
ro
rw
4355
0x1103
1
rw
8192
8193
8194
8195
8196
0x2000
0x2001
0x2002
0x2003
0x2004
1
1
1
1
1
ro
ro
ro
ro
ro
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
IP configuration: BootP(1),
DHCP(2) or fixed, coded IP
address(4)
Number of established TCP
connections
MODBUS TCP Timeout
(Changes apply only to new
connections)
MAC ID of the ETHERNET
interface (eth0)
MODBUS TCP response delay
PLC status
Watchdog Command
WatchdogStatus
Watchdog Timeout
(configuration register)
Watchdog Config (configuration
register)
0x0000 (constant)
0xFFFF (constant)
0x1234 (constant)
0xAAAA (constant)
0x5555 (constant)
282
MODBUS – CODESYS 2
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 205: WAGO MODBUS Registers
MODBUS Address Data Length
Access Description
in Words
Dec.
Hex.
8197
0x2005
1
ro
0x7FFF (constant)
8198
0x2006
1
ro
0x8000 (constant)
8199
0x2007
1
ro
0x3FFF (constant)
8200
0x2008
1
ro
0x4000 (constant)
8208
8209
8210
8211
8212
8213
0x2010
0x2011
0x2012
0x2013
0x2014
0x2015
1
1
1
1
1
1
ro
ro
ro
ro
ro
ro
Revision (Firmware Index)
Series code
Device code
Major Firmware Version
Minor Firmware Version
MBS Version
The WAGO MODBUS registers are described in more details in the following
sections.
10.5.1
Process Image Properties
10.5.1.1
Register 0x1022 – Number of Registers in the MODBUS Input
Process Image
This register contains the number of registers available in the MODBUS input
process image (MODBUS input).
10.5.1.2
Register 0x1023 – Number of Registers in the MODBUS Output
Process Image
This register contains the number of registers available in the MODBUS output
process image (MODBUS output).
10.5.1.3
Register 0x1024 – Number of Bits in the MODBUS Input Process
Image
This register contains the number of bits available in the MODBUS input process
image (MODBUS input).
10.5.1.4
Register 0x1025 – Number of Bits in the MODBUS Output Process
Image
This register contains the number of bits available in the MODBUS output
process image (MODBUS output).
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
10.5.2
Network Configuration
10.5.2.1
Register 0x1028 – IP Configuration
MODBUS – CODESYS 2
283
This register contains information about the set IP configuration.
Possible values:
1 = BootP
2 = DHCP
4 = Fixed IP address
10.5.2.2
Register 0x102A – Number of Established TCP Connections
This register supplies the number of established TCP connections.
The maximum number of MODBUS TCP connections is 1000.
10.5.2.3
Register 0x1030 – MODBUS TCP Socket Timeout
This register contains the timeout value for the TCP sockets.
This value is given in units of 100ms (ticks). A new value is accepted only for
new connections which have not yet been established. In the event of any
changes, pre-established connections will continue to operate using the previously
set timeout value.
10.5.2.4
Register 0x1031 – MAC Address for ETHERNET-Interface 1 (eth0)
This register provides the MAC address for the first ETHERNET interface (eth0).
MAC may also provide a partial result.
10.5.2.5
Register 0x1037 - MODBUS TCP Response Delay
This register saves the value of the MODBUS response delay.
This value is specified in ms units. The maximum delay is 32 ms, default value is
0 ms (no delay). Transmission of the response to a MODBUS request is delayed
from the time of processing (read and/or write register values) by the time set. In
the meantime, incoming requests can only be processed when the previous
response is sent. For MODBUS UDP, this applies to all requests and for
MODBUS TCP, for each connection. The actual length of time between a
MODBUS request and the associated response depends on the number of parallel
requests overall system utilization; it is always greater than the response delay set.
Changes to the response delay become effective immediately for each subsequent
request.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
284
MODBUS – CODESYS 2
10.5.3
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
PLC Status Register
Register 0x1040 provides the status (state) that the controller is currently in.
Possible values:
1 = PLC running − PLC status is RUNNING.
2 = PLC stopped − PLC status is STOPPED.
10.5.4
MODBUS Watchdog
The MODBUS watchdog monitors ongoing MODBUS communication. In the
event that the configured monitoring time (see “Watchdog Timeout” Register) is
exceeded without one single valid MODBUS query (trigger) being received from
a MODBUS slave, the watchdog reacts and initiates the “Watchdog Timeout”
reaction (previously configured in the “Watchdog Config” register). The
watchdog must be continuously triggered by the MODBUS master to ensure that
the set monitoring time does not expire. Triggering is performed by receiving any
arbitrary MODBUS query from the entire volume of services supported by the
MODBUS slave. These MODBUS-slave-supported services are listed in the
Section “MODBUS Mapping”. The Explicit Trigger Mode is an exception to this
rule and is elucidated in detail in the description of the “MODBUS Config”
register (0x1103).
10.5.4.1
Register 0x1100 – Watchdog Command
This register receives commands for the MODBUS watchdog.
The following commands are accepted:
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
MODBUS – CODESYS 2
285
Table 206: Watchdog Commands
Value
0x5555
Name
WATCHDOG_START
Error-free response
Explanation
Starts the watchdog
Watchdog has been successfully started, or
restarted, and has the status “Running”.
Error
ILLEGAL
Watchdog time has already expired. The
response FUNCTION
watchdog must be reset with the command
(0x01)
WATCHDOG_RESET.
ILLEGAL
Watchdog not configured, i.e., the
DATA VALUE “Watchdog Timeout” register (0x1102)
(0x03)
contains the value 0.
0x55AA WATCHDOG_STOP
Stops the watchdog
Error-free response
Watchdog was stopped successfully and
has the status “Stopped”.
Error
ILLEGAL
Watchdog monitoring time has already
response FUNCTION
expired. The watchdog must then first be
(0x01)
reset by the command
WATCHDOG_RESET.
ILLEGAL
Watchdog not configured, i.e., the
DATA VALUE “Watchdog Timeout” register (0x1102)
(0x03)
contains the value 0.
0xAAAA WATCHDOG_RESET
Resets the watchdog after a timeout
Error-free response
Watchdog was reset successfully and has
the status “Stopped” or “Unconfigured”
when the “Watchdog Timeout” register
(0x1102) contains the value 0.
Error
ILLEGAL
Watchdog does not have the status
response DATA VALUE “Expired”.
(0x03)
The watchdog is only started by the command WATCHDOG_START. A
prerequisite for successful startup is a valid timeout value in the “Watchdog
Timeout” register (0x1102) and the status “Stopped” or “Running” (for restart),
which the watchdog must have (see “Watchdog Status” register 0x1101). A
response of ILLEGAL_DATA_VALUE indicates that the watchdog has not yet
been configured (status “Unconfigured”, timeout value is “0”). If the watchdog
has the status “Expired”, the WATCHDOG_START command is also rejected by
the ILLEGAL_FUNCTION acknowledgement.
A running watchdog can be stopped by the command WATCHDOG_STOP. A
stop request received several times in a row does not have any impact on the
behavior of the watchdog and is therefore not acknowledged with an error
response. By contrast, a stop command received when the watchdog has the status
“Unconfigured” is rejected with the acknowledgement
ILLEGAL_DATA_VALUE; if the watchdog has the status “Expired” this
command is rejected by the exception code ILLEGAL_FUNCTION.
If the watchdog monitoring time has expired, the watchdog can only be reset by
the command WATCHDOG_RESET. The watchdog cannot be restart until this
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
286
MODBUS – CODESYS 2
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
command is executed. Resetting the watchdog does not necessarily restart it
automatically, however. To restart the watchdog after a reset, the command
WATCHDOG_START must be sent. Possible reactions to expiring of the
watchdog monitoring time (timeout) are described in the “Watchdog Config”
register (0x1102). If the command WATCHDOG_RESET is received when the
watchdog has a status other than “Expired”, this command is rejected with the
exception code ILLEGAL_DATA_VALUE.
10.5.4.2
Register 0x1101 – Watchdog Status
This register provides the current status of the MODBUS watchdog.
The watchdog can have any of the four following statuses:
Table 207: Watchdog Status
Value
Name
0xFFFF WATCHDOG_UNCONFIGURED
0x0000
WATCHDOG_STOPPED
0x0001
0x0002
WATCHDOG_RUNNING
WATCHDOG_EXPIRED
Explanation
Watchdog not configured, i.e., the
watchdog time-out register
(0x1102) contains the value 0.
Watchdog is not active (not
started).
Watchdog is active (started).
Watchdog monitoring time has
expired.
If the “Watchdog Timeout” register (0x1102) contains the value 0, the Watchdog
has not been configured − WATCHDOG_UNCONFIGURED. If the timeout
value remains unchanged (0), the Watchdog cannot leave this state. After a
configuration, the Watchdog switches to “Stopped” and can now be started.
The watchdog can only be started by the command WATCHDOG_START. When
the watchdog is started, it assumes the status “Running” WATCHDOG_RUNNING. Configuration changes in this state are no longer
possible.
When the watchdog expires (status WATCHDOG_EXPIRED), the registers
“Watchdog Status” (0x1101), “Watchdog Timeout” (0x1102) and “Watchdog
Config” (0x1103) are the only registers that can be read. Access to other registers,
with the exception of write access to the “Watchdog Command” register
(0x1100), and bit access is acknowledged by the error ILLEGAL FUNCTION.
The configuration registers can only be written in the watchdog statuses
WATCHDOG_UNCONFIGURED, WATCHDOG_STOPPED or
WATCHDOG_EXPIRED. Only read access is permitted for these registers in the
status WATCHDOG_RUNNING.
10.5.4.3
Register 0x1102 – Watchdog Timeout
This configuration register contains the watchdog timeout value. As the basic unit
is 100 ms, the timeout value must be a multiple of 100 ms. Thus, the minimum
timeout value can be set to 100 ms, while the maximum value can be set to
6553.5 seconds. If this value is 0, the watchdog cannot be started and will have
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
MODBUS – CODESYS 2
287
the status “Unconfigured”. The watchdog timeout register can be rewritten to the
states “Unconfigured”, “Stopped” or “Expired”. Access to this register is read
only while the watchdog is active.
10.5.4.4
Register 0x1103 – Watchdog Config
This register contains the configuration parameters for the watchdog.
The following parameters can be configured:
Table 208: Watchdog Configuration
Bit
0
1
2
Name/Bit Identifier
Explicit triggering
EXPLICIT_
TRIGGER_ONLY
Explanation
Controls explicit triggering
0 All supported MODBUS queries are considered
watchdog triggers (default setting). There is a
special rule for the “Watchdog Status” register.
See the description for bit 1
EXPLICIT_TRIGGER_ON_STATUS_REG.
1 Explicit Trigger Mode − only the command
WATCHDOG_START (0x5555), sent to the
“Watchdog Command” register (0x1100), or
reading of the “Watchdog Status” registers
(0x1101), when Bit 1
EXPLICIT_TRIGGER_ON_STATUS_REG has
been set accordingly, are considered valid
trigger events for the MODBUS watchdog.
Triggering by access Controls triggering by read-only access to the
to the watchdog status “Watchdog Status” register
register
0 Read access to the “Watchdog Status” register is
TRIGGER_ON_
not considered a trigger event (default setting).
STATUS_REG
1 Read access to the “Watchdog Status” register is
considered a trigger event.
Close-down of
Closes down all established TCP connections
established TCP
0 All established connections remain open.
connections
1 All established connections are closed (default
CLOSE_ALL_TCP_
setting).
CONNECTIONS
The individual options are activated when the specific bit, or bit combination, is
set.
The “Watchdog Config” register can be rewritten to the statuses “Unconfigured”,
“Stopped” or “Expired”. Access to this register is read only while the watchdog is
active.
10.5.5
MODBUS Constants Register
Registers 0x2000 … 0x2008 provide constants based on the table “WAGO
MODBUS Register”. It is possible to read all of the constants, or a consecutive
portion of them, at once.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
288
MODBUS – CODESYS 2
10.5.6
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Electronic Nameplate
Registers 0x2010 to 0x2015 contain information from the electronic nameplate. It
is possible to read the entire nameplate, or a consecutive portion of it, all at once.
10.5.6.1
Register 0x2010 – Revision (Firmware Index)
This register provides the consecutive revision index (firmware index) for the
PFC200.
Example: 5 for Version 5.
10.5.6.2
Register 0x2011 – Series Designator
This register provides the designation for the WAGO series (Series Code) of the
PFC200.
Example: 750 for WAGO-I/O SYSTEM 750.
10.5.6.3
Register 0x2012 – Device ID
This register provides the device ID (WAGO Item No.) of the controller.
Example: 8206.
10.5.6.4
Register 0x2013 – Major Firmware Version
This register provides the major part for the firmware version.
10.5.6.5
Register 0x2014 – Minor Firmware Version
This register provides the minor part for the firmware version.
10.5.6.6
Register 0x2015 – MBS Version
This register provides the version of the MODBUS slave library. The high byte
contains the major version number and the low byte, the minor version number.
Example:
0x010A => Major version number = 1, Minor version number = 10.
Pos : 63.7 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
MODBUS – CODESYS 2
289
Pos : 63.8 /Serie 750 (WAGO-I/O-SYST EM)/F eldbus kommuni kation/PFC/MOD BU S/MOD BUS 750-82xx - Diagnos e @ 26\mod_1465365448345_21.doc x @ 211984 @ 2333 @ 1
10.6
Diagnostics
10.6.1
Diagnostics for the MODBUS Master
The status of the PLC, or of the control system, can be queried by the MODBUS
master by reading the WAGO-specific register 0x1040 – “PLC Status” using
MODBUS services FC3 (Read Holding Registers) or FC4 (Read Input Registers).
The WAGO-specific register 0x1040 – “PLC Status” is explained in the Section
“PLC Status Registers”.
The status of the MODBUS Watchdog can be requested using a register service
(FC3 or FC4) with a query to the WAGO-specific register 0x1101 – “Watchdog
Status Register”. Information about this is given in the Section “MODBUS
Watchdog”.
The MODBUS service “Get Communication Event Counter” (FC11) is not
supported in the current MODBUS slave Version V1.0.
10.6.2
Diagnostics for the Runtime System
Diagnostics for the MODBUS slaves can be executed by integrating the
CODESYS library “BusDiag.lib” via the runtime system. The required function
block, “DiagGetBusState() indicates the status of the fieldbus (here MODBUS)
and is located in this library. Details about this function block are provided both in
this document and in the online Help function for CODESYS.
10.6.3
Diagnostics for the Error Server
The MODBUS slave also supports the error service implemented in the PFC and
generates diagnostic messages, which are stored permanently (in a file), or
temporarily (in the RAM) and can be displayed directly via the WBM client. The
following diagnoses are generated by the MODBUS slave:
Table 209: Diagnostics for the Error Server
Diagnostics
ID
0x00090000
0x00090001
0x00090002
0x00090003
0x00090004
0x00090005
Diagnostic text
Modbus Slave
library loaded
Modbus Slave
library closed
Modbus Slave
TCP started
Modbus Slave
TCP start failed
Modbus Slave
TCP terminated
Modbus Slave
UDP started
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Method of
saving
Temporary
Temporary
Temporary
Permanent
Temporary
Temporary
Explanation
MODBUS slave library has
been successfully loaded.
MODBUS slave library has
been successfully unloaded.
MODBUS slave successfully
started in TCP mode.
Starting the MODBUS slave in
the TCP mode failed.
MODBUS slave TCP mode
successfully terminated.
MODBUS slave successfully
started in UDP mode.
290
MODBUS – CODESYS 2
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 209: Diagnostics for the Error Server
Diagnostics
ID
0x00090006
0x00090007
0x00090008
0x00090009
0x0009000A
0x0009000B
0x0009000C
0x0009000F
0x00090100
0x00090101
0x00090102
0x00090103
0x00090104
0x00090105
0x00090106
0x00090107
Diagnostic text
Modbus Slave
UDP start failed
Modbus Slave
UDP terminated
Modbus Slave
RTU started
Modbus Slave
RTU start failed
Modbus Slave
RTU terminated
Modbus Slave data
exchange started
by PLC
Modbus Slave data
exchange stopped
by PLC
Modbus Slave
PLC watchdog
timer expired
Modbus Slave
common
configuration
failed.
Modbus Slave
TCP configured
successfully.
Modbus Slave
TCP configuration
failed.
Modbus Slave
UDP configured
successfully
Modbus Slave
UDP configuration
failed.
Modbus Slave
RTU configured
successfully.
Modbus Slave
RTU configuration
failed
Port for Modbus
Slave RTU
operation not free.
Method of
saving
Permanent
Temporary
Temporary
Permanent
Temporary
Temporary
Explanation
Starting the MODBUS slave in
UDP mode failed.
MODBUS slave UDP mode
successfully terminated.
MODBUS slave successfully
started in the RTU mode.
Starting the MODBUS slave in
RTU mode failed.
MODBUS slave RTU mode
successfully terminated.
MODBUS slave data
exchange started.
Temporary
MODBUS slave data
exchange stopped.
Permanent
Monitoring time for controller
(PLC) expired.
Permanent
MODBUS slave configuration
failed.
Temporary
MODBUS slave TCP
configuration completed
successfully.
MODBUS slave TCP
configuration failed.
Permanent
Temporary
Permanent
Temporary
Permanent
Permanent
MODBUS slave UDP
configuration completed
successfully.
MODBUS slave UDP
configuration failed.
MODBUS slave RTU
configuration completed
successfully.
MODBUS slave RTU
configuration failed.
Serial port for MODBUS slave
RTU configuration already
occupied.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
MODBUS – CODESYS 2
291
Table 209: Diagnostics for the Error Server
Diagnostics
ID
0x00090108
0x00090200
0x00090201
0x00090202
0x00090203
0x00090300
0x00090301
Diagnostic text
Modbus Slave
RTU configuration
in RS-485 mode
failed.
Modbus Slave
Watchdog
activated.
Modbus Slave
Watchdog
deactivated.
Modbus Slave
Watchdog Timer
expired.
Modbus Slave has
terminated all
established TCP
connections.
Modbus Slave:
obtaining system
resource failed
Modbus Slave:
processing system
resource failed.
Pos : 64 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Method of
saving
Permanent
Explanation
Temporary
MODBUS watchdog
activated.
Temporary
MODBUS watchdog
deactivated.
Permanent
MODBUS watchdog
monitoring time expired.
Permanent
All MODBUS TCP
connections terminated due to
timeout.
Permanent
Request for system resources
by the MODBUS slave has
failed.
Access to system resources by
the MODBUS slave has failed.
Permanent
MODBUS slave RTU
configuration for the RS-485
mode has failed.
292
MODBUS – e!RUNTIME
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 65 /Serie 750 ( WAGO-I/O-SYST EM)/F eldbus kommuni kation/PFC/MODBU S/MOD BU S - e!RUNTIME - Ü berschrift 1 @ 21\mod_1417783919676_21.doc x @ 170102 @ 1 @ 1
11
MODBUS – e!RUNTIME
Pos : 66.1 /Serie 750 (WAGO-I/O-SYST EM)/F eldbus kommuni kation/PFC/MOD BU S/MOD BUS 750-8xxx - MOD BU S-Adress übersic ht, e!RUNTIM E @ 26\mod_1465372617725_21.doc x @ 212004 @ 2 @ 1
11.1
MODBUS Address Overview
Figure 102: MODBUS Address Overview
Pos : 66.2 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Pos : 66.3 /Serie 750 (WAGO-I/O-SYST EM)/F eldbus kommuni kation/PFC/MOD BU S/MOD BUS 750-8xxx - WAGO-M ODBU S-Register, e!RUNTIME, <= F W06 @ 21\mod_1416382956945_21.doc x @ 168508 @ 234444434344443333 @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
11.2
MODBUS – e!RUNTIME
293
MODBUS Registers
Table 210: WAGO MODBUS Registers
MODBUS Address Data Length
Access Description
in Words
Dec.
Hex.
Watchdog configuration register
64,000
0xFA00
1
w
Watchdog command register
64,001
0xFA01
1
rw
Watchdog timeout register
64,002
0xFA02
1
ro
Watchdog status register
64,003
0xFA03
1
rw
Watchdog config register
MODBUS TCP connection
64,004
0xFA04
1
rw
watchdog register
Status registers
LED flash code I/O-LED
64,010
0xFA0A
1
ro
(sequence 1 of 3)
LED flash code I/O-LED
64,011
0xFA0B
1
ro
(sequence 2 of 3)
LED flash code I/O-LED
64,012
0xFA0C
1
ro
(sequence 3 of 3)
64,013
0xFA0D
1
ro
PLC State : 1 = Stop; 2 = Run
Electronic Type Label
Order number, e.g.,
64,016
0xFA10
4
ro
0750810100400001
64,020
0xFA14
1
ro
Firmware version
64,021
0xFA15
1
ro
Hardware version
64,022
0xFA16
1
ro
Firmware loader
Process Image Version
Version of the MODBUS
64,023
0xFA17
1
ro
process image
Network Configuration
64,032
0xFA20
3
ro
MAC-ID 1
Process Image Registers
Number of input registers, analog
64064
0xFA40
1
ro
and digital (total size of the
MODBUS IN space) 0x7D00
Number of input registers, analog
64065
0xFA41
1
ro
0x7D00
Number of input registers, digital
64066
0xFA42
1
ro
0x8000
Number of output registers,
analog and digital (total size of
64067
0xFA43
1
ro
the MODBUS OUT space)
0x7D00
Number of output registers,
64068
0xFA44
1
ro
analog 0x7D00
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
294
MODBUS – e!RUNTIME
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 210: WAGO MODBUS Registers
MODBUS Address Data Length
Access Description
in Words
Dec.
Hex.
Number of output registers,
64069
0xFA45
1
ro
digital 0x8000
Constants Register
64,160
0xFAA0
1
ro
Constant 0x1234
64,161
0xFAA1
1
ro
Constant 0xAAAA
64,162
0xFAA2
1
ro
Constant 0x5555
64,250
0xFAFA
1
ro
Live register
The WAGO MODBUS registers are described in more details in the following
sections.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
11.2.1
MODBUS – e!RUNTIME
295
MODBUS Watchdog
The MODBUS watchdog monitors ongoing MODBUS communication. If no
trigger event occurs during the configured watchdog time (see Section “Watchdog
Timeout Register”) when the watchdog is running (“Running” status, see Section
“Watchdog Status Register”), the state changes to “Expired” and an appropriate
event is triggered in the runtime system. The Watchdog Config register defines
which MODBUS requests from all the services supported by the MODBUS slave
are trigger events. These MODBUS slave supported services are listed in the
Section “MODBUS Mapping.”
11.2.1.1
Watchdog Command Register
The register 0xFA00 receives commands for the MODBUS watchdog.
The following commands are accepted:
Table 211: Watchdog Commands
Value
0x5555
Explanation
Starts the watchdog
The watchdog was started successfully
and is then in “Running” status. If a
watchdog is already running, the
command is regarded as an explicit trigger
event.
Error response ILLEGAL The watchdog has already expired
DATA VALUE (0x03)
(“Expired” status) or the watchdog is not
configured (“Unconfigured” status).
0x55AA WATCHDOG_STOP
Stops an active watchdog (only Advanced
mode)
Error-free response
Watchdog was stopped successfully and
then has the status “Stopped.”
Error response ILLEGAL The watchdog is not configured
DATA VALUE (0x03)
(“Unconfigured” status) or activated in
Simple mode.
0xAAAA WATCHDOG_RESET
Resets the watchdog after a timeout
(Advanced mode only)
Error-free response
The watchdog was successfully reset and
has then the “Stopped” status.
Error response ILLEGAL The watchdog has not expired (status is
DATA VALUE (0x03)
not “Expired”) or is activated in Simple
mode.
11.2.1.2
Name
WATCHDOG_START
Error-free response
Watchdog Timeout Register
The configuration register 0xFA01 contains the watchdog timeout value. The time
base is 1 ms. The time can therefore be set up to 65535 ms. If this value is 0, the
watchdog cannot be started and will have the “Unconfigured” status.
A write access to this register is not possible with the watchdog active (“Running”
or “Expired” status, see Section “Watchdog Status Register”) and is answered
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
296
MODBUS – e!RUNTIME
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
with the “ILLEGAL_FUNCTION” error message.
If the watchdog is inactive, a write access in “Simple mode” (see Section
“Watchdog Config Register,” Bit 7) immediately activates the watchdog and the
set watchdog time begins. In this case, the watchdog then has “Running” status.
If the watchdog is inactive, a write access in “Advanced Mode” keeps the
watchdog inactive and only switches it to “Stopped” status.
11.2.1.3
Watchdog Status Register
The register 0xFA02 provides the current status of the MODBUS watchdog.
The watchdog can have any of the four following states:
Table 212: Watchdog Status
Value
Name
0xFFFF WATCHDOG_UNCONFIGURED
0x0000
WATCHDOG_STOPPED
0x0001
0x0002
WATCHDOG_RUNNING
WATCHDOG_EXPIRED
Explanation
Watchdog not configured, i.e., the
“Watchdog Timeout” register
(0xFA01) contains the value 0.
Watchdog is configured but not
active (not started).
Watchdog is active (started).
The watchdog is active and the
watchdog monitoring time has
expired.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
11.2.1.4
MODBUS – e!RUNTIME
297
Watchdog Config Register
The register 0xFA03 contains the configuration parameters for the watchdog.
The following parameters can be configured:
Table 213: Watchdog Configuration
Bit
0
1
2
Name/Bit Identifier
Explicit triggering
EXPLICIT_
TRIGGER_ONLY
Explanation
Controls explicit triggering
0 All supported MODBUS requests are considered
as watchdog triggers (default setting). There is a
special rule for the Watchdog Status register.
See the description for bit 1
EXPLICIT_TRIGGER_ON_STATUS_REG.
1 Explicit Trigger Mode − only the command
WATCHDOG_START (0x5555), sent to the
Watchdog Command register (0xFA00), or
reading of the Watchdog Status register
(0xFA02), when Bit 1
EXPLICIT_TRIGGER_ON_STATUS_REG has
been set accordingly, are considered as valid
trigger events for the MODBUS watchdog.
Triggering by access Controls triggering by read-only access to the
to the watchdog status Watchdog Status register
register
0 Read access to the Watchdog Status register is
TRIGGER_ON_
not considered a trigger event (default setting).
STATUS_REG
1 Read access to the Watchdog Status register is
considered a trigger event.
Close-down of
Controls the behavior of TCP connections with the
established TCP
watchdog timeout (transition to “Expired” status)
connections
0 All established connections remain open.
CLOSE_ALL_TCP_ 1 All established connections are closed (default
CONNECTIONS
setting).
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
298
MODBUS – e!RUNTIME
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 213: Watchdog Configuration
Bit
7
Name/Bit Identifier
Advanced/Simple
mode switchover
SELECTION_
ADVANCED_
SIMPLE_MODE
Explanation
Determines the mode in which the watchdog is
operating.
0 Advanced Mode: The watchdog can only be
started, stopped or reset with the Watchdog
Command register (0xFA00). A write access to
the Watchdog Config register (0xFA03) is not
possible with the watchdog active (“Running” or
“Expired” status). (Default setting)
1 Simple Mode: The watchdog is triggered with
any valid MODBUS-TCP/UDP query, the
settings of Bit 0 … 2 are taken into account
here. If the watchdog times out (“Expired”
status), it is implicitly reset and started with the
next valid trigger. The watchdog can only be
stopped by switching to Advanced mode.
The individual options are activated if the relevant bit or bit combination is set.
A write access to this register in Advanced mode (see bit 7) is not possible with
the watchdog active (“Running” or “Expired” status, see Section “Watchdog
Status Register”) and is answered in this case with the error
“ILLEGAL_FUNCTION.”
11.2.1.5
MODBUS TCP Connection Watchdog Register
The register 0xFA04 contains the duration for the MODBUS-TCP connection
monitoring. The time base is 10 ms. A time of up to 655350 ms can be set. If the
register contains a value > 0 when a new TCP connection from a MODBUS
master is accepted, the monitoring for this connection is started. Later changes to
the register have no effect on the monitoring of existing connections. If the
monitoring is started and no telegram is received from the connected MODBUS
master within the set time, this connection is closed from one side with a reset.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
11.2.2
Status Registers
11.2.2.1
PLC Status Register
MODBUS – e!RUNTIME
299
The register 0xFA0D supplies the current status of the controller.
Possible values:
1 = PLC Stop - PLC is in STOP status.
2 = PLC Run - PLC is in RUN status
11.2.3
Electronic Nameplate
Registers 0xFA10–0xFA17 contain information from the electronic nameplate. It
is possible to read the entire nameplate or a consecutive portion of it all at once.
11.2.3.1
Order Number
The registers 0xFA10–0xFA13 contain the WAGO order number of the
controller.
Example: 0750-8202/0025-0001.
0xFA10 = 0750,
0xFA11 = 8202,
0xFA12 = 0025,
0xFA13 = 0001
11.2.3.2
Firmware Version
The register 0xFA14 contains the firmware version of the controller.
11.2.3.3
Hardware Version
The register 0xFA15 contains the hardware version of the controller.
11.2.3.4
Firmware Loader/Boot Loader
The register 0xFA16 contains the firmware loader/boot loader version of the
controller.
11.2.4
MODBUS Process Image Version
The register 0xFA17 contains the MODBUS process image version of the
controller.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
300
MODBUS – e!RUNTIME
11.2.5
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
MODBUS Process Image Registers
The registers 0xFA40–0xFA45 contain size information for the process image
spaces of the controller for bit and register accesses.
11.2.6
Constants Registers
Registers 0xFAA0–0xFAA2 provide constants based on the “WAGO MODBUS
Registers” table. It is possible to read all of the constants, or a consecutive portion
of them at once.
0xFAA0 = 0x1234,
0xFAA1 = 0xAAAA,
0xFAA2 = 0x5555
11.2.7
Live Register
The register 0xFAFA can only be read and contains a counter that is incremented
with each cycle of a task of the runtime environment with read and write access to
the MODBUS process data.
Pos : 66.4 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
MODBUS – e!RUNTIME
301
Pos : 66.5 /Serie 750 (WAGO-I/O-SYST EM)/F eldbus kommuni kation/PFC/MOD BU S/MOD BUS 750-8xxx - MOD BU S-Master Abschätz ung CPU- Las t @ 22\mod_1424932765167_21.doc x @ 175948 @ 2 @ 1
11.3
Estimating the MODBUS Master CPU Load
Due to the real-time characteristics of the Linux® kernel used, many data points
can generate many context changes.
For a one-off update (transmitting and receiving of a function code), a CPU time
of approx. 800 µs can be assumed.
The CPU load (cpu_load) in percent can be estimated from the cycle time (t_z) for
a query with the following rule of thumb:
cpu_load = 800 µs / t_z * 100
A cycle time of 100 ms thus results in a CPU load of 0.8%.
A maximum load of approx. 20% can be generated per connection, as this is
limited by the network protocol. To minimize the CPU load:
-
The cycle time must be as high as possible.
-
As many data points as possible must be combined in a query.
-
The minimum query interval can be increased (default value: 0 ms).
Pos : 67 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
302
MODBUS – e!RUNTIME
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 68 /Serie 750 ( WAGO-I/O-SYST EM)/F eldbus kommuni kation/PFC/MODBU S/MOD BU S 750-8xxx - M ODBU S-Master Abschätz ung CPU- Last @ 22\mod_1424932765167_21.doc x @ 175948 @ 2 @ 1
11.4
Estimating the MODBUS Master CPU Load
Due to the real-time characteristics of the Linux® kernel used, many data points
can generate many context changes.
For a one-off update (transmitting and receiving of a function code), a CPU time
of approx. 800 µs can be assumed.
The CPU load (cpu_load) in percent can be estimated from the cycle time (t_z) for
a query with the following rule of thumb:
cpu_load = 800 µs / t_z * 100
A cycle time of 100 ms thus results in a CPU load of 0.8%.
A maximum load of approx. 20% can be generated per connection, as this is
limited by the network protocol. To minimize the CPU load:
-
The cycle time must be as high as possible.
-
As many data points as possible must be combined in a query.
-
The minimum query interval can be increased (default value: 0 ms).
Pos : 69 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Diagnostics
303
Pos : 70 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 1/Diagnos e - Ü bers chrift 1 @ 4\mod_1240831069471_21.doc x @ 31372 @ 1 @ 1
12
Diagnostics
Pos : 71.1 /Serie 750 (WAGO-I/O-SYST EM)/Di agnose/PFC xxx/Di agnose 750- 8xxx - LED-Signalisier ung - Betriebs- und Status meldung en @ 15\mod_1370929506932_21.doc x @ 122280 @ 2 @ 1
12.1
Operating and Status Messages
The following tables contain descriptions of all operating and status messages for
the controller which are indicated by LEDs.
Pos : 71.2 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Anz eigeelemente/PFC xxx/Anz eigeelemente 750-8xxx/0040- xxxx - Vers orgung, Ü bersc hrift 3 + Abbildung + Legendentabelle @ 22\mod_1426084900501_21.doc x @ 177468 @ 3 @ 1
12.1.1
Power Supply Indicating Elements
Figure 103: Power Supply Indicating Elements
Table 214: Legend for Figure “Power Supply Indicating Elements”
Description
A
C
Color
Green/off
Green/off
Description
Status of system power supply voltage
Status of field-side power supply voltage
Pos : 71.3 /Serie 750 (WAGO-I/O-SYST EM)/Di agnose/PFC xxx/Di agnose 750- 8xxx - LED-Signalisier ung Versorgung @ 13\mod_1344425979437_21.doc x @ 101615 @ @ 1
Table 215: Field-Side Supply Diagnostics
Status
Green
Off
Explanation
24V field-side supply
voltage present
No 24V field-side supply
voltage present
Table 216: System Power Supply Diagnistics
Status
Green
Off
Explanation
24V system power supply
voltage present
No 24V system power
supply voltage present
Pos : 71.4 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Solution
--Switch on the power
supply. Check the supply
voltage.
Solution
--Switch on the power
supply. Check the supply
voltage.
304
Diagnostics
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 71.5 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Anz eigeelemente/PFC xxx/Anz eigeelemente 750-8xxx - F eldbus/System, Ü berschrift 3 @ 13\mod_1342507577846_21.doc x @ 100424 @ 3 @ 1
12.1.2
Fieldbus/System Indicating Elements
Pos : 71.6 /Serie 750 (WAGO-I/O-SYST EM)/Ger ätebesc hrei bung/Anz eigeelemente/PFC xxx/Anz eigeelemente 750-8202 - F el dbus/Sys tem, Abbildung @ 12\mod_1341838179308_21.doc x @ 99282 @ @ 1
Figure 104: Indicating Elements for Fieldbus/System
Pos : 71.7 /Serie 750 (WAGO-I/O-SYST EM)/Di agnose/PFC xxx/Di agnose 750- 8xxx - LED-Signalisier ung SYS >= FW06 @ 23\mod_1436170600242_21.doc x @ 185178 @ @ 1
Table 217: Diagnostics via SYS LED
Status
Green
Explanation
Ready to operate System start
completed without
errors
Yellow
Device is in
startup/boot process
and the RST button is
not pressed.
Yellow flashing “Fix IP Address”
mode,
temporary setting
until the next reboot
Green/red
Firmware update
flashing
mode
Remedy
---
---
Connect to the device via the standard
address (192.168.1.17) or restart the
device to restore the original value set.
---
Pos : 71.8 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Diagnostics
305
Pos : 71.9 /Serie 750 (WAGO-I/O-SYST EM)/Di agnose/PFC xxx/Di agnose 750- 82xx - LED- Signalisierung RUN - Ergänzung Laufz eits ystem @ 20\mod_1410514320347_21.doc x @ 163268 @ @ 1
The RUN LED indication depends on the runtime system enabled (CODESYS 2
or e!RUNTIME).
Pos : 71.10 /Serie 750 ( WAGO-I/O-SYST EM)/Diagnos e/PFC xxx/Diagnos e 750- 82xx - LED-Sig nalisi erung RUN - Ergänz ung COD ESYS 2 @ 20\mod_1410514665922_21.doc x @ 163272 @ @ 1
The following indications apply to the CODESYS 2 runtime system:
Pos : 71.11 /Serie 750 ( WAGO-I/O-SYST EM)/Diagnos e/PFC xxx/Diagnos e 750- 82xx - LED-Sig nalisi erung RUN, C ODESYS 2 @ 13\mod_1344417549184_21.doc x @ 101600 @ @ 1
Table 218: Diagnostics RUN LED
Status
Green
Green flashing
Green/red flashing
Red
Explanation
PLC program has the
status “Run”.
PLC program at a debug
point.
PLC is at a debug point
and the Run/Stop switch
has been set to “Stop”.
No PLC-program loaded
or PLC program has the
status “Stop”.
Pos : 71.12 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Solution
--Resume the program in
the linked IDE (Integrated
Development
Environment) using
“Single step” or “Start”. If
the connection has been
interrupted, set the
Run/Stop switch to “Stop”
and then back to “Run” to
enable the program to
continue.
Set the Run/Stop switch to
“Run” to enable the
program to continue.
Load the PLC program.
Set the Run/Stop switch to
“Run” to start the current
program.
306
Diagnostics
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 71.13 /Serie 750 ( WAGO-I/O-SYST EM)/Diagnos e/PFC xxx/Diagnos e 750- 82xx - LED-Sig nalisi erung RUN - Ergänz ung e!RUNTIM E @ 20\mod_1410514673352_21.doc x @ 163276 @ @ 1
The following indications apply to the e!RUNTIME runtime system:
Pos : 71.14 /Serie 750 ( WAGO-I/O-SYST EM)/Diagnos e/PFC xxx/Diagnos e 750- 8xxx - LED-Signalisierung RUN, e!RUNTIM E >= F W06 @ 23\mod_1432806216983_21.doc x @ 183028 @ @ 1
Table 219: RUN LED Diagnostics – e!RUNTIME
Status
Green
Explanation
Applications loaded
and all in the “RUN”
status
Green flashing No application and
now boot project
loaded
Red
Applications loaded
and all in the “STOP”
status
Green/red
At least one
flashing
application in the
“RUN” status and one
in the ”STOP” status
Red,
Warm start reset
goes out briefly completed
Red,
Cold start reset
goes out longer completed
Red, flashing
At least one
application after in
the “STOP” status
after exception (e.g.,
memory access error)
Orange/green
flashing
Orange
OFF
Remedy
--Load an application or boot project.
Set the mode selector switch to “RUN”
to start the application.
Start the stopped application.
-----
Start the application with a reset via the
mode selector switch or in the connected
IDE.
If the application cannot be started,
restart the controller.
Contact WAGO Support if the error
occurs again.
Load above threshold Try to reduce the load on the system:
value 1
- Change the CODESYS program.
- End any fieldbus communication
that is not essential, or reconfigure
the fieldbuses.
- Remove any non-critical tasks from
the RT area.
- Select a longer cycle time for IEC
tasks.
Runtime system in
Resume the application in the connected
debug state
IDE with single step or start.
(breakpoint, single
Remove the breakpoint if necessary.
step, individual cycle) If the connection has been interrupted,
set the mode selector switch to “STOP”
and then back to “RUN” to enable the
application to continue
No runtime system
Enable a runtime system, e.g., via the
loaded
WBM.
Pos : 71.15 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Diagnostics
307
Pos : 71.16 /Serie 750 ( WAGO-I/O-SYST EM)/Diagnos e/PFC xxx/Diagnos e 750- 8xxx - LED-Signalisierung I/O @ 20\mod_1410348309051_21.doc x @ 163055 @ @ 1
Table 220: Diagnostics I/O LED
Status
Green
Orange flashing
Red
Red flashing
(2 Hz)
Red flashing
(flashing sequence)
Off
Explanation
Data cycle on the internal
data bus, normal operating
status.
Startup phase; the internal
data bus is being
initialized. The startup
phase is indicated by rapid
flashing for about 1 ... 2
seconds.
A hardware fault is
present.
An error which may be
able to be eliminated is
present.
Solution
--Wait until initialization
has been completed.
Contact WAGO Support.
First, try to eliminate the
error by switching the
device (power supply) off
and then back on.
Check the entire node
structure for any errors.
If you cannot eliminate
the error, contact WAGO
Support.
An internal data bus error An explanation of the
is present.
flashing sequence is given
in the section
“Diagnostics Messages
(I/O LEDs)”.
A library was not loaded, Restart the device.
or a library function was If you cannot eliminate
not called up.
the error, contact WAGO
Support.
Pos : 71.17 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
308
Diagnostics
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 71.18 /Serie 750 ( WAGO-I/O-SYST EM)/Diagnos e/PFC xxx/Diagnos e 750- 82xx PFC 200 - LED-Signalisier ung - Diagnos emel dungen I/Diag nos e 750- 8xxx - LED-Signalisier ung - Di agnos emel dungen I/O- LED @ 15\mod_1370929717650_21.doc x @ 122284 @ 2 @ 1
12.2
Diagnostics Messages (I/O LED)
Pos : 71.19 /Serie 750 ( WAGO-I/O-SYST EM)/Diagnos e/PFC xxx/Diagnos e 750- 8xxx - Blinkcodes, Ablauf der Bli nks equenz @ 12\mod_1341919775937_21.doc x @ 99497 @ 3 @ 1
12.2.1
Flashing Sequence
A diagnosis (fault/error) is always displayed as three flashing sequences in a
cyclic manner:
1.
The first flashing sequence (flickering) initiates reporting of the fault/error.
2.
After a short break (approx. 1 second), the second flashing sequence starts.
The number of blink pulses indicates the error code, which describes the
type of error involved.
3.
After a further break the third flashing sequence is initiated. The number of
blink pulses indicates the error argument, which provides an additional
description of the error, e.g., which of the I/O modules connected to the
controller exhibits an error.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Figure 105: Flashing Sequence Process Diagram
Pos : 71.20 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Diagnostics
309
310
Diagnostics
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 71.21 /Serie 750 ( WAGO-I/O-SYST EM)/Diagnos e/PFC xxx/Diagnos e 750- 8xxx - Blinkcodes, Beispi el ei ner Diagnos emel dung mittels Blinkcode @ 12\mod_1341919904406_21.doc x @ 99520 @ 3 @ 1
12.2.2
Example of a Diagnostics Message Indicated by a Blink
Code
The example below illustrates the representation of a diagnostics message via the
blink code. A data error is indicated on the internal data bus, caused by the
removal of an I/O module located at the 6th position of the bus node.
Initiation of the Start Phase
1.
The I/O LED flashes for 1 cycle at about 10 Hz (10 flashes/second).
2.
This is followed by a pause of about one second.
Error Code 4: Data Error in the Internal Data Bus
3.
The I/O LED flashes for 4 cycles of about 1Hz.
4.
This is followed by a pause of about 1 second.
Error Argument 5: I/O Module at the 6th Slot
5.
The I/O LED flashes for 5 cycles at 1 Hz.
This indicates that a disruption has occurred at the I/O module downcircuit
of the 5th I/O module.
6.The blink code starts flickering when the start phase is initiated again. If there is
only one error, this process is repeated.
Pos : 71.22 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Diagnostics
311
Pos : 71.23 /Serie 750 ( WAGO-I/O-SYST EM)/Diagnos e/PFC xxx/Diagnos e 750- 8xxx - Blinkcodes, F ehlerc odes Ei nleitung @ 12\mod_1341910164730_21.doc x @ 99445 @ 3 @ 1
12.2.3
Meaning of Blink Codes and Procedures for
Troubleshooting
This section describes the diagnostics presented as blink codes via the I/O LEDs.
If the diagnostics cannot be cleared by the measured specified for them, contact
WAGO support. Be ready to explain to them the blink code that is displayed.
Phone:
Fax:
E-mail:
+49 571 887 555
+49 571 887 8555
support@wago.com
Pos : 71.24 /Serie 750 ( WAGO-I/O-SYST EM)/Diagnos e/PFC xxx/Diagnos e 750- 8xxx - Blinkcodes, F ehlerc odes Übersicht >= F W06 @ 22\mod_1426768947793_21.doc x @ 178126 @ @ 1
Table 221: Overview of Error Codes
Error code
1
2
3
4
5
6
7
8
9
Explanation
Hardware and configuration error
Configuration error
Internal data bus protocol error
Physical error on the internal data bus
Internal data bus initialization error
Not used
Not used
Not used
CPU exception error
Pos : 71.25 /Serie 750 ( WAGO-I/O-SYST EM)/Diagnos e/PFC xxx/Diagnos e 750- 8xxx - Blinkcodes, F ehlerc ode 1 Bedeutung und M aßnahmen >= F W06 @ 22\mod_1426768407459_21.doc x @ 178118 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
312
Diagnostics
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 222: Error Code 1, Explanation of Blink Codes and Procedures for Troubleshooting
Error
Argument
-
1
Cause
Remedy
Invalid parameter
checksum for internal
data bus interface
Internal buffer
overflow (max.
amount of data
exceeded) during
inline code
generation.
-
-
2
Data type of the I/O
module(s) is not
supported
-
-
-
3
4
5
6
Unknown module
type of the flash
program memory
Error occurred while
writing to the flash
memory
Error occurred while
erasing a flash sector
The I/O module
configuration after an
internal data bus reset
differs from the one
after the last
controller startup.
-
-
Switch off the power to the
controller and replace it.
Then switch the power back on.
Switch off the power to the
controller.
Reduce the number of I/O modules.
Switch the power back on.
Update the controller firmware. If
this error persists, there is an error in
the I/O module. Identify the error as
follows:
Switch off the power supply.
Place the end module in the middle
of the I/O modules connected to the
system.
Switch the power back on.
If the I/O flashes red switch off the
power supply again and place the
end module in the middle of the first
half of the I/O modules (toward the
controller).
If the LED is no longer flashing,
switch off the power supply and
place the end module in the middle
of the second half of the I/O modules
(away from the controller).
Switch the power back on.
Repeat this procedure until you
establish which I/O module is
defective. Then replace that module.
Switch off the power to the
controller and replace it.
Then switch the power back on.
Switch off the power to the
controller and replace it.
Then switch the power back on.
Restart the controller by first
switching off the power supply and
then switching it back on, or
by pressing the Reset button on the
controller.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Diagnostics
313
Table 222: Error Code 1, Explanation of Blink Codes and Procedures for Troubleshooting
Error
Argument
7
8
9
10
11
12
14
16
Cause
Remedy
Error occurred while writing to the serial
EEPROM
Invalid hardware/
firmware combination
Invalid checksum in
the serial EEPROM
Fault when
initializing the serial
EEPROM.
Error occurred while
reading from the
serial EEPROM
Time to access the
serial EEPROM
exceeded
Maximum number of
gateway or mailbox
modules exceeded.
Maximum number of
I/O modules exceeded -
Switch off the power to the
controller and replace it.
Then switch the power back on.
Switch off the power supply to the
controller and reduce the number of
I/O modules.
Then switch the power back on.
Switch off the power to the
controller and replace it.
Then switch the power back on.
Switch off the power to the
controller.
Reduce the number of gateway or
mailbox modules.
Then switch the power back on.
Switch off the power to the
controller.
Reduce the number of I/O modules.
Then switch the power back on.
Pos : 71.26 /Serie 750 ( WAGO-I/O-SYST EM)/Diagnos e/PFC xxx/Diagnos e 750- 8xxx - Blinkcodes, F ehlerc ode 2 Bedeutung und M aßnahmen >= F W06 @ 22\mod_1424425269957_21.doc x @ 175228 @ @ 1
Table 223: Error Code 2, Explanation of Blink Codes and Procedures for Troubleshooting
Error
Argument
2
Cause
Remedy
Maximum size of the
process image
exceeded
-
Pos : 71.27 /Serie 750 ( WAGO-I/O-SYST EM)/Diagnos e/PFC xxx/Diagnos e 750- 8xxx - Blinkcodes, F ehlerc ode 3 Bedeutung und M aßnahmen @ 12\mod_1341913143621_21.doc x @ 99474 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Switch off the power to the
controller.
Reduce the number of I/O modules.
Switch the power back on.
314
Diagnostics
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 224: Error Code 3, Explanation of Blink Codes and Procedures for Troubleshooting
Error
Cause
Argument
Solution
If a power supply module (e.g., 750-602)
is connected to the controller, ensure that
this module functions properly (see
Section “LED Signaling”). If the supply
module does not exhibit any errors/faults,
the I/O module is defective. Identify the
defective I/O module as follows:
-
--
Internal data bus
communication error;
defective I/O module
cannot be identified
Switch off the power supply.
Place the end module in the middle
of the I/O modules connected to the
system.
Switch the power back on.
If the I/O LED continues to flash red
switch off the power supply again
and place the end module in the
middle of the first half of the I/O
modules (toward the controller).
If only one I/O module is left and the
LED continues to flash, either this
module or the controller internal data bus
interface is defective. Replace the
defective module or the controller.
-
-
If the LED is no longer flashing,
switch off the power supply and
place the end module in the middle
of the second half of the I/O modules
(away from the controller).
Switch the power back on.
Repeat this procedure until you
establish which I/O module is
defective. Then replace that module.
Pos : 71.28 /Serie 750 ( WAGO-I/O-SYST EM)/Diagnos e/PFC xxx/Diagnos e 750- 8xxx - Blinkcodes, F ehlerc ode 4 Bedeutung und M aßnahmen @ 12\mod_1341913874133_21.doc x @ 99478 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Diagnostics
315
Table 225: Error Code 4, Explanation of Blink Codes and Procedures for Troubleshooting
Error
Cause
Argument
--
n*
Maximum permissible
number of I/O modules
exceeded.
Internal data bus
disruption after the nth
process data module.
Solution
-
Switch off the power to the
controller.
Reduce the number of I/O modules to
an acceptable value.
Switch the power back on.
Switch off the power to the
controller.
Replace the (n+1)th process data
module.
Switch the power back on.
I/O modules that do not provide any data
are ignored (e.g., supply module without
diagnostics).
Pos : 71.29 /Serie 750 ( WAGO-I/O-SYST EM)/Diagnos e/PFC xxx/Diagnos e 750- 8xxx - Blinkcodes, F ehlerc ode 5 Bedeutung und M aßnahmen @ 12\mod_1341914332680_21.doc x @ 99482 @ @ 1
Table 226: Error Code 5, Explanation of Blink Codes and Procedures for Troubleshooting
Error
Cause
Argument
n*
Register communication
error during internal data
bus initialization
Solution
-
Switch off the power to the
controller.
Replace the (n+1)th process data
module.
Switch the power back on.
I/O modules that do not provide any data
are ignored (e.g., supply module without
diagnostics).
Pos : 71.30 /Serie 750 ( WAGO-I/O-SYST EM)/Diagnos e/PFC xxx/Diagnos e 750- 8xxx - Blinkcodes, F ehlerc ode 9 Bedeutung und M aßnahmen @ 12\mod_1341914723071_21.doc x @ 99490 @ @ 1
Table 227: Error Code 9, Explanation of Blink Codes and Procedures for Troubleshooting
Error
Cause
Argument
1
Invalid program statement
2
Stack overflow
3
Stack underflow
4
Invalid event (NMI)
Pos : 72 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Solution
Malfunction of the program sequence.
- Please contact WAGO Support.
Malfunction of the program sequence.
- Please contact WAGO Support.
Malfunction of the program sequence.
- Please contact WAGO Support.
Malfunction of the program sequence.
- Please contact WAGO Support.
316
Service
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 73 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 1/Ser vice - Übersc hrift 1 @ 4\mod_1241771948421_21.doc x @ 32830 @ 1 @ 1
13
Service
Pos : 74 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 2/Speic her karte einfüg en und entfer nen - Ü berschrift 2 @ 16\mod_1375437291463_21.doc x @ 127683 @ 2 @ 1
13.1
Inserting and Removing the Memory Card
Pos : 75.1 /Serie 750 (WAGO-I/O-SYST EM)/Ser vic e/Speic her-/SIM-Karten/PFC xxx - Ser vic e - Speic her karte einfügen @ 23\mod_1432701883376_21.doc x @ 182896 @ 3 @ 1
</dg_
13.1.1
Inserting the Memory Card
1.
Use an actuating tool or a screwdriver to open the transparent cover flap by
flipping it upwards. The point where to position the tool is marked with an
arrow.
2.
Hold the memory card so that the contacts are visible on the right and the
diagonal edge is at the top, as depicted in the figure below.
3.
Insert the memory card in this position into the slot provided for it.
4.
Push the memory card all the way in. When you let go, the memory card
will move back a little and then snap in place (push-push mechanism).
5.
Close the cover flap by flipping it down and pushing it in until it snaps into
place.
6.
You can seal the closed flap through the hole in the enclosure next to the
flap.
Pos : 75.2 /Serie 750 (WAGO-I/O-SYST EM)/Ser vic e/Speic her-/SIM-Karten/PFC 200 - Ser vice - Speicher kar te ei nfügen - Abbildung SD-Karte @ 23\mod_1432701879599_21.doc x @ 182892 @ @ 1
Figure 106: Inserting the Memory Card
Pos : 75.3 /Serie 750 (WAGO-I/O-SYST EM)/Ser vic e/Speic her-/SIM-Karten/PFC xxx - Ser vic e - Speic her karte entfernen @ 23\mod_1432701875895_21.doc x @ 182888 @ 3 @ 1
</dg_
13.1.2
Removing the Memory Card
1.
First, remove any seal that may be in place.
2.
Use an actuating tool or a screwdriver to open the transparent cover flap by
flipping it upwards. The point where to position the tool is marked with an
arrow.
3.
To remove the memory card you must first push it slightly into the slot
(push-push mechanism). This releases the mechanical locking mechanism.
4.
As soon as you let go of the memory card, the memory card is pushed out a
bit and you can remove it.
5.
Remove the memory card.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
6.
Service
317
Close the cover flap by flipping it down and pushing it in until it snaps into
place.
Pos : 76 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Pos : 77 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 2/Firmware- Änder ungen - Übersc hrift 2 @ 23\mod_1432702695498_21.doc x @ 182919 @ 2 @ 1
13.2
Firmware Changes
Pos : 78.1 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/HinweisHi nweis : U p-/Downgrade des C ontroll ers - Pas sende Dokumentati on ber eithalten @ 22\mod_1430212191564_21.doc x @ 181458 @ @ 1
Obtain documentation appropriate for the firmware target version!
A firmware upgrade or downgrade can modify, remove or add controller
properties and functions. As a result, described properties or functions of the
controller may not be available or available properties or functions may not be
described in the documentation. Therefore, use only documentation appropriate
for the target firmware after an upgrade/downgrade.
If you have any questions, feel free to contact our WAGO Support.
Pos : 78.2 /Serie 750 (WAGO-I/O-SYST EM)/Ser vic e/Fir mwar e-ÄnderungPFC xxx - Servic e - Firmware-U pgrade durchführen @ 22\mod_1430209685490_21.doc x @ 181448 @ 3 @ 1
13.2.1
Perform Firmware Upgrade
Do not switch the controller off!
The controller can be damaged by interrupting the upgrade process.
Do not switch the controller off during the upgrade process and do not disconnect
the power supply!
Proceed as follows if you want to upgrade the controller to a later firmware
version:
1.
Save your application and the controller settings.
2.
Switch off the controller.
3.
Insert the memory card with the new firmware image into the memory card
slot.
4.
Switch on the controller.
5.
After booting the controller, launch the WBM “Create Boot Image” page
(you may have to temporarily change the IP address).
6.
Create a new boot image on the internal memory.
7.
Switch off the controller after completing the process.
8.
Remove the memory card.
9.
Switch on the controller.
The controller can now be started with the new firmware version.
Pos : 78.3 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
318
Service
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 78.4 /Serie 750 (WAGO-I/O-SYST EM)/Ser vic e/Fir mwar e-ÄnderungPFC xxx - Servic e - Firmware-D owngrade durc hführ en @ 22\mod_1430209928786_21.doc x @ 181451 @ 3 @ 1
13.2.2
Perform Firmware Downgrade
Do not switch the controller off!
The controller can be damaged by interrupting the downgrade process.
Do not switch the controller off during the downgrade process and do not
disconnect the power supply!
Note the firmware version
For devices with a factory installation of a firmware >= FW 05, a simple
downgrade to a version <= FW 04 is not possible!
Use a special downgrade image.
Proceed as follows if you want to downgrade the controller to an earlier firmware
version:
1.
Save your application and the controller settings.
2.
Switch off the controller.
3.
Insert the memory card with the new firmware image into the memory card
slot. Use a special downgrade image if necessary.
4.
Switch on the controller.
5.
After booting the controller, launch the WBM “Create Boot Image” page
(you may have to temporarily change the IP address).
6.
Create a new boot image on the internal memory.
7.
Switch off the controller after completing the process.
8.
Remove the memory card.
9.
Switch on the controller.
The controller can now be started with the new firmware version.
Pos : 78.5 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Service
319
Pos : 78.6 /Serie 750 (WAGO-I/O-SYST EM)/Ser vic e/Fir mwar e-Änderung/PFC xxx - Ser vice - F actor y-Res et - Hinweise und einl eitende Besc hrei bung, >= F W06 @ 24\mod_1443592817538_21.doc x @ 192576 @ 3 @ 1
13.2.3
Factory Reset
Do not switch the controller off!
The controller can be damaged by interrupting the factory reset process.
Do not switch the controller off during the factory reset process and do not
disconnect the power supply!
All parameters and passwords are overwritten!
All controller parameters and passwords are overwritten by a factory reset.
Any subsequently installed firmware functions are not overwritten.
If you have any questions, contact WAGO Support.
The controller is restarted after the factory reset.
Proceed as follows to factory reset the controller:
Pos : 78.7 /Serie 750 (WAGO-I/O-SYST EM)/Ser vic e/Fir mwar e-Änderung/PFC xxx - Ser vice - F actor y-Res et - Durc hführ ung - SYS- LED, >= F W06 @ 19\mod_1402044028520_21.doc x @ 155323 @ @ 1
1.
Press the Reset button (RST).
2.
Set the mode selector switch to the “RESET” position.
3.
Press and hold both buttons until the “SYS” LED alternately flashes
red/green after approx. 8 seconds.
4.
When the “SYS” LED flashes red/green alternately, release the mode
selector switch and Reset button.
Do not interrupt the reset process!
If you release the Reset button (RST) too early, then the controller restarts without
performing the factory reset.
Pos : 79 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
320
Removal
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 80 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 1/Demontier en - Übersc hrift 1 @ 12\mod_1329144208186_21.doc x @ 88668 @ 1 @ 1
14
Removal
Pos : 81.1 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/Vorsic ht/Vorsicht: Verl etz ungsgefahr durc h s charfkantige M ess er kontakte! @ 6\mod_1256193279401_21.doc x @ 43414 @ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury.
Pos : 81.2 /Serie 750 (WAGO-I/O-SYST EM)/M ontieren/D emontieren/Geräte entfernen - Übersc hrift 2 @ 16\mod_1378817501993_21.doc x @ 131078 @ 2 @ 1
14.1
Removing Devices
Pos : 81.3 /All e Seri en ( Allgemei ne Module)/Sicherheits- und s ons tige Hi nweis e/Ac htung/Achtung: Arbeiten an Ger äten nur s pannungsfr ei durc hführ en! @ 6\mod_1256193963573_21.doc x @ 43426 @ @ 1
Perform work on devices only if they are de-energized!
Working on energized devices can damage them. Therefore, turn off the power
supply before working on the devices.
Pos : 81.4 /Serie 750 (WAGO-I/O-SYST EM)/M ontieren/D emontieren/Fel dbus koppl er/Fel dbus koppl er/-c ontroller entfernen @ 4\mod_1239169358453_21.doc x @ 30330 @ 3 @ 1
14.1.1
Removing the Fieldbus Coupler/Controller
1.
Use a screwdriver blade to turn the locking disc until the nose of the locking
disc no longer engages behind the carrier rail.
2.
Remove the fieldbus coupler/controller from the assembly by pulling the
release tab.
Electrical connections for data or power contacts to adjacent I/O modules are
disconnected when removing the fieldbus coupler/controller.
Pos : 81.5 /Serie 750 (WAGO-I/O-SYST EM)/M ontieren/D emontieren/Verriegelung - Bild (C ontroller PFC xxx) XTR @ 24\mod_1441789683702_21.doc x @ 191048 @ @ 1
Figure 107: Release Tab of Controller (Example)
Pos : 81.6 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/Hinweis/Hi nweis: Gehäus eteile des C ontroll ers nicht tr ennen! @ 16\mod_1376636663788_21.doc x @ 129124 @ @ 1
Do not take the controller enclosure apart!
The enclosure sections are firmly joined. The feed-in section with the CAGE
CLAMP® connections cannot be separated from the other enclosure section.
Pos : 81.7 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Removal
321
Pos : 81.8 /Serie 750 (WAGO-I/O-SYST EM)/M ontieren/D emontieren/Bus klemme entfernen @ 4\mod_1239169375203_21.doc x @ 30334 @ 3 @ 1
14.1.2
Removing the I/O Module
1.
Remove the I/O module from the assembly by pulling the release tab.
Figure 108: Removing the I/O Module (Example)
Electrical connections for data or power jumper contacts are disconnected when
removing the I/O module.
Pos : 81.9 /Serie 750 (WAGO-I/O-SYST EM)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/Hinweis/Hi nweis: Gehäus eteile des C ontroll ers nicht tr ennen! @ 16\mod_1376636663788_21.doc x @ 129124 @ @ 1
Do not take the controller enclosure apart!
The enclosure sections are firmly joined. The feed-in section with the CAGE
CLAMP® connections cannot be separated from the other enclosure section.
Pos : 82 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
322
Use in Hazardous Environments
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 83.1 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/Ebene 1Eins atz in expl osionsgefährdeten Bereic hen - Übersc hrift 1 @ 3\mod_1224075191281_21.doc x @ 24084 @ 1 @ 1
15
Use in Hazardous Environments
Pos : 83.2 /Serie 750 (WAGO-I/O-SYST EM)/Eins atz in Ex- Ber eichen/Ei ns atz ber eich Serie 750 @ 3\mod_1234272230203_21.doc x @ 27500 @ @ 1
The WAGO-I/O-SYSTEM 750 (electrical equipment) is designed for use in
Zone 2 hazardous areas.
The following sections include both the general identification of components
(devices) and the installation regulations to be observed. The individual
subsections of the “Installation Regulations” section must be taken into account if
the I/O module has the required approval or is subject to the range of application
of the ATEX directive.
Pos : 83.3 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Use in Hazardous Environments
323
Pos : 83.4 /Serie 750 (WAGO-I/O-SYST EM)/Eins atz in Ex- Ber eichen/Beis piel hafter Aufbau der Kennz eic hnung - Übersc hrift 2 @ 3\mod_1224157499140_21.doc x @ 24182 @ 2 @ 1
15.1
Marking Configuration Examples
Pos : 83.5 /Serie 750 (WAGO-I/O-SYST EM)/Eins atz in Ex- Ber eichen/Kennz eic hnung für Europa gemäß ATEX und IEC- EX - Übersc hrift 3 @ 3\mod_1224157620203_21.doc x @ 24185 @ 3 @ 1
15.1.1
Marking for Europe According to ATEX and IEC-Ex
Pos : 83.6 /Serie 750 (WAGO-I/O-SYST EM)/Eins atz in Ex- Ber eichen/Beis piel bedruc kung der ATEX- und IEC- Ex-zug elass enen Bus klemmen gemäß C ENELEC und IEC_2013 @ 14\mod_1360569228625_21.doc x @ 111294 @ @ 1
Figure 109: Side Marking Example for Approved I/O Modules According to ATEX and IECEx
Figure 110: Text Detail – Marking Example for Approved I/O Modules According to ATEX and
IECEx.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
324
Use in Hazardous Environments
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 228: Description of Marking Example for Approved I/O Modules According to ATEX and
IECEx
Printing on Text
TÜV 07 ATEX 554086 X
IECEx TUN 09.0001 X
Dust
II
3D
Ex
tc Dc
IIIC
T 135°C
Mining
I
M2
Ex
d Mb
I
Gases
II
3G
Ex
nA Gc
nC Gc
IIC
T4
Description
Approving authority and certificate numbers
Equipment group: All except mining
Category 3 (Zone 22)
Explosion protection mark
Type of protection and equipment protection
level (EPL):protection by enclosure
Explosion group of dust
Max. surface temperature of the enclosure
(without a dust layer)
Equipment group: Mining
Category: High level of protection
Explosion protection mark
Type of protection and equipment protection
level (EPL): Flameproof enclosure
Explosion group for electrical equipment for
mines susceptible to firedamp
Equipment group: All except mining
Category 3 (Zone 2)
Explosion protection mark
Type of protection and equipment protection
level (EPL): Non-sparking equipment
Type of protection and equipment protection
level (EPL): Sparking apparatus with protected
contacts. A device which is so constructed that
the external atmosphere cannot gain access to the
interior
Explosion group of gas and vapours
Temperature class: Max. surface temperature
135°C
Pos : 83.7 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Use in Hazardous Environments
325
Pos : 83.8 /Serie 750 (WAGO-I/O-SYST EM)/Eins atz in Ex- Ber eichen/Beis piel bedruc kung der Ex-i- und IEC-Ex-i-zug elas senen Bus klemmen gemäß C ENELEC und IEC _2013 @ 14\mod_1360569320118_21.doc x @ 111298 @ @ 1
Figure 111: Side Marking Example for Approved Ex i I/O Modules According to ATEX and
IECEx.
Figure 112: Text Detail – Marking Example for Approved Ex i I/O Modules According to ATEX
and IECEx.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
326
Use in Hazardous Environments
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 229: Description of Marking Example for Approved Ex i I/O Modules According to ATEX
and IECEx
Inscription Text
TÜV 07 ATEX 554086 X
IECEx TUN 09.0001X
TÜV 12 ATEX 106032 X
IECEx TUN 12.0039 X
Dust
II
3(1)D
3(2)D
Ex
tc Dc
[ia Da]
[ib Db]
IIIC
T 135°C
Mining
I
M2 (M1)
Ex d Mb
[ia Ma]
I
Description
Approving authority and certificate numbers
Equipment group: All except mining
Category 3 (Zone 22) equipment containing a safety
device for a category 1 (Zone 20) equipment
Category 3 (Zone 22) equipment containing a safety
device for a category 2 (Zone 21) equipment
Explosion protection mark
Type of protection and equipment protection level
(EPL): protection by enclosure
Type of protection and equipment protection level
(EPL): associated apparatus with intrinsic safety
circuits for use in Zone 20
Type of protection and equipment protection level
(EPL): associated apparatus with intrinsic safety
circuits for use in Zone 21
Explosion group of dust
Max. surface temperature of the enclosure (without a
dust layer)
Equipment Group: Mining
Category: High level of protection with electrical
circuits which present a very high level of protection
Explosion protection mark with Type of protection
and equipment protection level (EPL): Flameproof
enclosure
Type of protection and equipment protection level
(EPL): associated apparatus with intrinsic safety
electrical circuits
Explosion group for electrical equipment for mines
susceptible to firedamp
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Use in Hazardous Environments
327
Table 229: Description of Marking Example for Approved Ex i I/O Modules According to ATEX
and IECEx
Gases
II
3(1)G
3(2)G
Ex
nA Gc
[ia Ga]
[ia Gb]
IIC
T4
Equipment group: All except mining
Category 3 (Zone 2) equipment containing a safety
device for a category 1 (Zone 0) equipment
Category 3 (Zone 2) equipment containing a safety
device for a category 2 (Zone 1) equipment
Explosion protection mark
Type of protection and equipment protection level
(EPL): Non-sparking equipment
Type of protection and equipment protection level
(EPL): associated apparatus with intrinsic safety
circuits for use in Zone 0
Type of protection and equipment protection level
(EPL): associated apparatus with intrinsic safety
circuits for use in Zone 1
Explosion group of gas and vapours
Temperature class: Max. surface temperature 135°C
Pos : 83.9 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
328
Use in Hazardous Environments
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 83.10 /Serie 750 ( WAGO-I/O-SYST EM)/Ei ns atz i n Ex-Bereic hen/Kennz eichnung für Ameri ka gemäß N EC 500 - Übersc hrift 3 @ 3\mod_1224158423187_21.doc x @ 24188 @ 3 @ 1
15.1.2
Marking for America According to NEC 500
Pos : 83.11 /Serie 750 ( WAGO-I/O-SYST EM)/Ei ns atz i n Ex-Bereic hen/Beispi elbedruc kung gemäß NEC 500_2013 @ 14\mod_1360580302684_21.doc x @ 111353 @ @ 1
Figure 113: Side Marking Example for I/O Modules According to NEC 500
Figure 114: Text Detail – Marking Example for Approved I/O Modules According to NEC 500
Table 230: Description of Marking Example for Approved I/O Modules According to NEC 500
Printing on Text
CL I
DIV 2
Grp. ABCD
Op temp code T4
Description
Explosion protection group (condition of use
category)
Area of application
Explosion group (gas group)
Temperature class
Pos : 83.12 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Use in Hazardous Environments
329
Pos : 83.13 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Ebene 2Erric htungs bes timmungen - Ü bersc hrift 2 @ 3\mod_1232453624234_21.doc x @ 26370 @ 2 @ 1
15.2
Installation Regulations
Pos : 83.14 /Alle Serien (Allgemeine M odul e)/Ei ns atz i n Ex-Bereic hen/Errichtungsbes timmungen Ei nleitung_2013 @ 14\mod_1360582328318_21.doc x @ 111371 @ @ 1
For the installation and operation of electrical equipment in hazardous areas, the
valid national and international rules and regulations which are applicable at the
installation location must be carefully followed.
Pos : 83.15 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
330
Use in Hazardous Environments
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 83.16 /Serie 750 ( WAGO-I/O-SYST EM)/Ei ns atz i n Ex-Bereic hen/Besonder e Beding ung en für den sic her en Ex- Betrieb gem. AT EX-Z ertifi kat TÜV 14 ATEX 148929_X @ 21\mod_1416995371807_21.doc x @ 169118 @ 3 @ 1
15.2.1
Special Conditions for Safe Use (TÜV 14 ATEX 148929 X)
1.
2.
3.
4.
Pos : 83.17 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
The modules of the WAGO-I/O-SYSTEM 750-*** have to been erected in
such a way, that corresponding to EN 60079-15 a degree of protection of at
least IP 54 according to EN 60529 is achieved.
Measures have to been taken, external to the modules, to provide a transient
protection that ensures that the rated voltage, connected to the power supply
terminals, is not exceeded by more than 40 %.
The connecting and disconnecting of the non-intrinsically safe circuits is
only permitted if no explosive atmosphere exists. This although applies for
the all switches, interfaces (Fieldbus, Ethernet, Serial) and the SD-card.
The ambient temperature range is: 0 °C ≤ Tamb ≤ +60 °C
The ambient temperature range for modules with suffix extension /025-****
is: -20 °C ≤ Tamb ≤ +60 °C
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Use in Hazardous Environments
331
Pos : 83.18 /Serie 750 ( WAGO-I/O-SYST EM)/Ei ns atz i n Ex-Bereic hen/Besonder e Beding ung en für den sic her en Ex- Betrieb gem. AT EX-Z ertifi kat TÜV 12 ATEX 106032x_2013_2 @ 15\mod_1368620479454_21.doc x @ 119782 @ 3 @ 1
15.2.2
Special Conditions for Safe Use (ATEX Certificate TÜV 12
ATEX 106032 X)
1.
2.
3.
4.
For use as Gc- or Dc-apparatus (in zone 2 or 22) the Field bus Independent
I/O Modules WAGO-I/O-SYSTEM 750-*** Ex i shall be erected in an
enclosure that fulfils the requirements of the applicable standards (see the
marking) EN 60079-0, EN 60079-11, EN 60079-15 and EN 60079-31.
For use as group I electrical apparatus M2 the apparatus shall be erected in
an enclosure that ensures a sufficient protection according to EN 60079-0
and EN 60079-1 and the degree of protection IP64.
The compliance of these requirements and the correct installation into an
enclosure or a control cabinet of the devices shall be certified by an ExNB.
Measures have to be taken outside of the device that the rating voltage is not
being exceeded of more than 40 % because of transient disturbances.
The connecting and disconnecting of the non-intrinsically safe circuits is
only permitted during installation, for maintenance or for repair purposes.
The temporal coincidence of explosion hazardous atmosphere and
installation, maintenance resp. repair purposes shall be excluded.
For the type the following shall be considered: The Interface circuits shall
be limited to overvoltage category I/II (non mains/mains circuits) as defined
in EN 60664-1.
Pos : 83.19 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
332
Use in Hazardous Environments
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 83.20 /Serie 750 ( WAGO-I/O-SYST EM)/Ei ns atz i n Ex-Bereic hen/Besonder e Beding ung en für den sic her en Ex- Betrieb gem. IEC-Ex-Z ertifi kat TUN 14.0035 X_2014 @ 21\mod_1416995779884_21.doc x @ 169122 @ 3 @ 1
15.2.3
Special Conditions for Safe Use (IEC-Ex Certificate TUN
14.0035X)
1.
2.
3.
4.
Pos : 83.21 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
The modules of the WAGO-I/O-SYSTEM 750-*** have to been erected in
such a way, that corresponding to IEC 60079-15 a degree of protection of at
least IP 54 according to IEC 60529 is achieved.
Measures have to been taken, external to the modules, to provide a transient
protection that ensures that the rated voltage, connected to the power supply
terminals, is not exceeded by more than 40 %.
The connecting and disconnecting of the non-intrinsically safe circuits is
only permitted if no explosive atmosphere exists. This although applies for
the all switches, interfaces (Fieldbus, Ethernet, Serial) and the SD-card.
The ambient temperature range is: 0 °C ≤ Tamb ≤ +60 °C
The ambient temperature range for modules with suffix extension /025-****
is: -20 °C ≤ Tamb ≤ +60 °C
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Use in Hazardous Environments
333
Pos : 83.22 /Serie 750 ( WAGO-I/O-SYST EM)/Ei ns atz i n Ex-Bereic hen/Besonder e Beding ung en für den sic her en Ex- Betrieb gem. IEC-Ex-Z ertifi kat TUN 12.0039 X_2013_2 @ 15\mod_1368620821493_21.doc x @ 119790 @ 3 @ 1
15.2.4
Special Conditions for Safe Use (IEC-Ex Certificate IECEx
TUN 12.0039 X)
1.
2.
3.
4.
For use as Gc- or Dc-apparatus (in zone 2 or 22) the Field bus independent
I/O Modules WAGO-I/O-SYSTEM 750-*** Ex i shall be erected in an
enclosure that fulfils the requirements of the applicable standards (see the
marking) IEC 60079-0, IEC 60079-11, IEC 60079-15, IEC 60079-31.
For use as group I electrical apparatus M2 the apparatus shall be erected in
an enclosure that ensures a sufficient protection according to IEC 60079-0
and IEC 60079-1 and the degree of protection IP64.
The compliance of these requirements and the correct installation into an
enclosure or a control cabinet of the devices shall be certified by an ExCB.
Measures have to be taken outside of the device that the rating voltage is not
being exceeded of more than 40 % because of transient disturbances.
The connecting and disconnecting of the non-intrinsically safe circuits is
only permitted during installation, for maintenance or for repair purposes.
The temporal coincidence of explosion hazardous atmosphere and
installation, maintenance resp. repair purposes shall be excluded.
For the type the following shall be considered: The Interface circuits shall
be limited to overvoltage category I/II (non mains/mains circuits) as defined
in IEC 60664-1.
Pos : 83.23 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
334
Use in Hazardous Environments
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 83.24 /Serie 750 ( WAGO-I/O-SYST EM)/Ei ns atz i n Ex-Bereic hen/Errichtungsbesti mmung en AN SI ISA 12.12.01_2013_2_für 750-439, -633, - 663/000-003 @ 21\mod_1417518338537_21.doc x @ 169812 @ 3 @ 1
15.2.5
Special Conditions for Safe Use according to ANSI/ISA
12.12.01
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
“This equipment is suitable for use in Class I, Division 2, Groups A, B, C, D
or non-hazardous locations only.”
“This equipment is to be fitted within tool-secured enclosures only.”
“WARNING Explosion hazard - substitution of components may impair
suitability for Class I, Div. 2.”
“WARNING – Do not disconnect equipment unless power has been
switched off or the area is known to be non-hazardous” has to be placed
near each operator accessible connector and fuse holder.
When a fuse is provided, the following information shall be provided: “A
switch suitable for the location where the equipment is installed shall be
provided to remove the power from the fuse.”
For devices with EtherCAT/Ethernet connectors “Only for use in LAN, not
for connection to telecommunication circuits.”
“WARNING - Use Module 750-642 only with antenna module 758-910.”
For Couplers/Controllers and Economy bus modules only: The instructions
shall contain the following: “The configuration interface Service connector
is for temporary connection only. Do not connect or disconnect unless the
area is known to be non-hazardous. Connection or disconnection in an
explosive atmosphere could result in an explosion.”
Modules containing fuses only: “WARNING - Devices containing fuses
must not be fitted into circuits subject to over loads, e.g. motor circuits.”
Modules containing SD card reader sockets only: “WARNING - Do not
connect or disconnect SD-Card while circuit is live unless the area is known
to be free of ignitable concentrations of flammable gases or vapors.”
The modules 750-439, 750-538, 750-633, 750-663/000-003 shall only be
supplied with 750-606 or 750-625/000-001.
Module 750-538 only “In Hazardous Locations, Non-Incendive only when
installed per Control Drawing No. 750-538”.
Pos : 83.25 /D okumentati on allgemei n/Gli ederungsel emente/------Leerz eile------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1
Pos : 83.26 /D okumentati on allgemei n/Gli ederungsel emente/------Leerz eile------ @ 3\mod_1224662755687_0.doc x @ 24460 @ @ 1
Pos : 83.27 /Serie 750 ( WAGO-I/O-SYST EM)/Ei ns atz i n Ex-Bereic hen/Infor mati on: Zer tifizier ungs nachweis @ 7\mod_1274279547729_21.doc x @ 56649 @ @ 1
Additional Information
Proof of certification is available on request.
Also take note of the information given on the operating and assembly
instructions.
The manual, containing these special conditions for safe use, must be readily
available to the user.
Pos : 84 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
335
Pos : 85 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 1/Anhang - Übersc hrift 1 @ 4\mod_1239874070437_21.doc x @ 30560 @ 1 @ 1
16
Appendix
Pos : 86.1 /Serie 750 (WAGO-I/O-SYST EM)/Proz ess abbild Mapping/PFC xxx/750- 82xx Proz ess abbild - Ei nlei tung Pr ozessdatenaufbau @ 16\mod_1379574243975_21.doc x @ 132004 @ 2 @ 1
16.1
Structure of Process Data for the I/O Modules
The process image for the I/O modules on the internal data bus is built up wordby-word in the controller (with word alignment). The internal mapping method for
data greater than one byte conforms to Intel formats.
The following section describes the representation for WAGO-I/O SYSTEM 750
(750 and 753 Series) I/O modules in the process image, as well as the
configuration of the process values.
Equipment damage due to incorrect address!
To prevent any damage to the device in the field you must always take the process
data for all previous byte or bit-oriented I/O modules into account when
addressing an I/O module at any position in the fieldbus node.
Pos : 86.2 /Serie 750 (WAGO-I/O-SYST EM)/Proz ess abbild Mapping/PFC xxx/Hi nweis: Kei n direkter Z ugriff vom F el dbus auf das Proz ess abbild der Bus kl emmen! @ 16\mod_1379510128893_21.doc x @ 131836 @ @ 1
No direct access from fieldbus to the process image for I/O modules!
Any data that is required from the I/O module process image must be explicitly
mapped in the CODESYS program to the data in the fieldbus process image and
vice versa! Direct access is not possible!
Pos : 86.3 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
336
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 86.4 /Serie 750 (WAGO-I/O-SYST EM)/Proz ess abbild Mapping/ETHERN ET - EtherN et/IP - MOD BUS/TCP/PA ETHERN ET- Digital e Klemmen MOD BUS/TCP (750- 342, -352, -830, - 842, -849) @ 5\mod_1253542361394_21.doc x @ 41900 @ 3444444443444444444 @ 1
16.1.1
Digital Input Modules
Digital input modules supply one bit of data per channel to specify the signal state
for the corresponding channel. These bits are mapped into the Input Process
Image.
Some digital modules have an additional diagnostic bit per channel in the Input
Process Image. The diagnostic bit is used for detecting faults that occur (e.g., wire
breaks and/or short circuits).
When analog input modules are also present in the node, the digital data is always
appended after the analog data in the Input Process Image, grouped into bytes.
16.1.1.1
1 Channel Digital Input Module with Diagnostics
750-435
Table 231: 1 Channel Digital Input Module with Diagnostics
Input Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
16.1.1.2
Bit 2
Bit 1
Diagnostic
bit
S1
Bit 0
Data bit
DI 1
2 Channel Digital Input Modules
750-400, -401, -405, -406, -410, -411, -412, -427, -438, (and all variations),
753-400, -401, -405, -406, -410, -411, -412, -427
Table 232: 2 Channel Digital Input Modules
Input Process Image
Bit 7
Bit 6
Bit 5
Bit 4
16.1.1.3
Bit 3
Bit 2
Bit 1
Bit 0
Data bit
Data bit
DI 2
DI 1
Channel 2 Channel 1
2 Channel Digital Input Module with Diagnostics
750-419, -421, -424, -425,
753-421, -424, -425
Table 233: 2 Channel Digital Input Module with Diagnostics
Input Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Diagnostic Diagnostic Data bit
Data bit
bit S 2
bit S 1
DI 2
DI 1
Channel 2 Channel 1 Channel 2 Channel 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
16.1.1.4
Appendix
337
2 Channel Digital Input Module with Diagnostics and Output Process
Data
750-418,
753-418
The digital input module supplies a diagnostic and acknowledge bit for each input
channel. If a fault condition occurs, the diagnostic bit is set. After the fault
condition is cleared, an acknowledge bit must be set to re-activate the input. The
diagnostic data and input data bit is mapped in the Input Process Image, while the
acknowledge bit is in the Output Process Image.
Table 234: 2 Channel Digital Input Module with Diagnostics and Output Process Data
Input Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Diagnostic Diagnostic Data bit
Data bit
bit S 2
bit S 1
DI 2
DI 1
Channel 2
Channel 1 Channel 2 Channel 1
Output Process Image
Bit 7
Bit 6
Bit 5
16.1.1.5
Bit 4
Bit 3
Bit 2
Acknowledge- Acknowledgement bit Q 2
ment bit Q 1
Channel 2
Channel 1
Bit 1
Bit 0
0
0
4 Channel Digital Input Modules
750-402, -403, -408, -409, -414, -415, -422, -423, -428, -432, -433, -1420, -1421,
-1422, -1423
753-402, -403, -408, -409, -415, -422, -423, -428, -432, -433, -440
Table 235: 4 Channel Digital Input Modules
Input Process Image
Bit 7
Bit 6
Bit 5
Bit 4
16.1.1.6
Bit 3
Data bit
DI 4
Channel 4
Bit 2
Bit 1
Bit 0
Data bit
Data bit
Data bit
DI 3
DI 2
DI 1
Channel 3 Channel 2 Channel 1
8 Channel Digital Input Modules
750-430, -431, -436, -437, -1415, -1416, -1417, -1418
753-430, -431, -434
Table 236: 8 Channel Digital Input Modules
Input Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Data bit
Data bit
Data bit
Data bit
Data bit
Data bit
Data bit
Data bit
DI 8
DI 7
DI 6
DI 5
DI 4
DI 3
DI 2
DI 1
Channel 8 Channel 7 Channel 6 Channel 5 Channel 4 Channel 3 Channel 2 Channel 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
338
Appendix
16.1.1.7
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
8 Channel Digital Input Module PTC with Diagnostics and Output
Process Data
750-1425
The digital input module PTC provides via one logical channel 2 byte for the
input and output process image.
The signal state of PTC inputs DI1 … DI8 is transmitted to the fieldbus
coupler/controller via input data byte D0.
The fault conditions are transmitted via input data byte D1.
The channels 1 … 8 are switched on or off via the output data byte D1. The output
data byte D0 is reserved and always has the value “0“.
Table 237: 8 Channel Digital Input Module PTC with Diagnostics and Output Process Data
Input Process Image
Input Byte D0
Input Byte D1
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Signal
status
DI 8
Channel 8
Signal
status
DI 7
Channel 7
Signal
status
DI 6
Channel 6
Signal
status
DI 5
Channel 5
Signal
status
DI 4
Channel 4
Signal
status
DI 3
Channel 3
Signal
status
DI 2
Channel 2
Signal
status
DI 1
Channel 1
Wire Wire Wire Wire Wire Wire Wire Wire
break/ break/ break/ break/ break/ break/ break/ break/
short short short short short short short short
circuit circuit circuit circuit circuit circuit circuit circuit
DB/KS DB/KS DB/KS DB/KS DB/KS DB/KS DB/KS DB/KS
8
7
6
5
4
3
2
1
Chan- Chan- Chan- Chan- Chan- Chan- Chan- Channel 8 nel 7 nel 6 nel 5 nel 4 nel 3 nel 2 nel 1
Output Process Image
Output Byte D0
Output Byte D1
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
DI
Off 7
Channel 7
0:
Channel
ON
1:
Channel
OFF
DI
Off 6
Channel 6
0:
Channel
ON
1:
Channel
OFF
DI
Off 5
Channel 5
0:
Channel
ON
1:
Channel
OFF
DI
Off 4
Channel 4
0:
Channel
ON
1:
Channel
OFF
DI
Off 3
Channel 3
0:
Channel
ON
1:
Channel
OFF
DI
Off 2
Channel 2
0:
Channel
ON
1:
Channel
OFF
DI
Off 1
Channel 1
0:
Channel
ON
1:
Channel
OFF
Table 238: 16 Channel Digital Input Modules
Input Process Image
Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6
Data Data Data Data Data Data Data Data Data Data
bit
bit bit bit bit bit bit
bit bit DI bit
DI 16 DI 15 DI 14 DI 13 DI 12 DI 11 DI 10 DI 9 8 DI 7
Chann Chan Chan Chan Chan Chan Chann Chan Chan Chan
el 16 nel 15 nel 14 nel 13 nel 12 nel 11 el 10 nel 9 nel 8 nel 7
Bit 5
Data
bit
DI 6
Chan
nel 6
Bit 4
Data
bit
DI 5
Chan
nel 5
Bit 3
Data
bit
DI 4
Chan
nel 4
Bit 2
Data
bit
DI 3
Chan
nel 3
Bit 1
Data
bit
DI 2
Chan
nel 2
Bit 0
Data
bit
DI 1
Chan
nel 1
0
16.1.1.8
0
0
0
0
0
0
0
DI
Off 8
Channel 8
0:
Channel
ON
1:
Channel
OFF
16 Channel Digital Input Modules
750-1400, -1402, -1405, -1406, -1407
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
16.1.2
Appendix
339
Digital Output Modules
Digital output modules use one bit of data per channel to control the output of the
corresponding channel. These bits are mapped into the Output Process Image.
Some digital modules have an additional diagnostic bit per channel in the Input
Process Image. The diagnostic bit is used for detecting faults that occur (e.g., wire
breaks and/or short circuits). For modules with diagnostic bit is set, also the data
bits have to be evaluated.
When analog output modules are also present in the node, the digital image data is
always appended after the analog data in the Output Process Image, grouped into
bytes.
16.1.2.1
1 Channel Digital Output Module with Input Process Data
750-523
The digital output modules deliver 1 bit via a process value Bit in the output
process image, which is illustrated in the input process image. This status image
shows "manual mode".
Table 239: 1 Channel Digital Output Module with Input Process Data
Input Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
not used
Output Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
not used
16.1.2.2
Bit 0
Status bit
“Manual
Operation“
Bit 0
controls
DO 1
Channel 1
2 Channel Digital Output Modules
750-501, -502, -509, -512, -513, -514, -517, -535, (and all variations),
753-501, -502, -509, -512, -513, -514, -517
Table 240: 2 Channel Digital Output Modules
Output Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Bit 3
Bit 2
Bit 1
Bit 0
controls
controls
DO 2
DO 1
Channel 2 Channel 1
340
Appendix
16.1.2.3
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
2 Channel Digital Input Modules with Diagnostics and Input Process
Data
750-507 (-508), -522,
753-507
The digital output modules have a diagnostic bit for each output channel. When an
output fault condition occurs (i.e., overload, short circuit, or broken wire), a
diagnostic bit is set. The diagnostic data is mapped into the Input Process Image,
while the output control bits are in the Output Process Image.
Table 241: 2 Channel Digital Input Modules with Diagnostics and Input Process Data
Input Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Diagnostic
bit S 2
Channel 2
Output Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
controls
DO 2
Channel 2
Bit 0
Diagnostic
bit S 1
Channel 1
Bit 0
controls
DO 1
Channel 1
750-506,
753-506
The digital output module has 2-bits of diagnostic information for each output
channel. The 2-bit diagnostic information can then be decoded to determine the
exact fault condition of the module (i.e., overload, a short circuit, or a broken
wire). The 4-bits of diagnostic data are mapped into the Input Process Image,
while the output control bits are in the Output Process Image.
Table 242: 2 Channel Digital Input Modules with Diagnostics and Input Process Data 75x-506
Input Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Diagnostic Diagnostic Diagnostic Diagnostic
bit S 3
bit S 2
bit S 1
bit S 0
Channel 2 Channel 2 Channel 1 Channel 1
Diagnostic bits S1/S0, S3/S2: = ‘00’
standard mode
Diagnostic bits S1/S0, S3/S2: = ‘01’
no connected load/short circuit against +24 V
Diagnostic bits S1/S0, S3/S2: = ‘10’
Short circuit to ground/overload
Output Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
not used
not used
Bit 1
controls
DO 2
Channel 2
Bit 0
controls
DO 1
Channel 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
16.1.2.4
Appendix
341
4 Channel Digital Output Modules
750-504, -516, -519, -531,
753-504, -516, -531, -540
Table 243: 4 Channel Digital Output Modules
Output Process Image
Bit 7
Bit 6
Bit 5
Bit 4
16.1.2.5
Bit 3
Bit 2
Bit 1
controls
controls
controls
DO 4
DO 3
DO 2
Channel 4 Channel 3 Channel 2
Bit 0
controls
DO 1
Channel 1
4 Channel Digital Output Modules with Diagnostics and Input
Process Data
750-532
The digital output modules have a diagnostic bit for each output channel. When an
output fault condition occurs (i.e., overload, short circuit, or broken wire), a
diagnostic bit is set. The diagnostic data is mapped into the Input Process Image,
while the output control bits are in the Output Process Image.
Table 244: 4 Channel Digital Output Modules with Diagnostics and Input Process Data
Input Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Diagnostic Diagnostic Diagnostic Diagnostic
bit
bit
bit
bit
S4
S3
S2
S1
Channel 4 Channel 3 Channel 2 Channel 1
Diagnostic bit S = ‘0’
no Error
Diagnostic bit S = ‘1’
overload, short circuit, or broken wire
Output Process Image
Bit 7
Bit 6
16.1.2.6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
controls
controls
controls
DO 4
DO 3
DO 2
Channel 4 Channel 3 Channel 2
Bit 0
controls
DO 1
Channel 1
Table 245: 8 Channel Digital Output Module
Output Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
controls
controls
controls
controls
controls
controls
controls
DO 8
DO 7
DO 6
DO 5
DO 4
DO 3
DO 2
Channel 8 Channel 7 Channel 6 Channel 5 Channel 4 Channel 3 Channel 2
Bit 0
controls
DO 1
Channel 1
8 Channel Digital Output Module
750-530, -536, -1515, -1516
753-530, -534
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
342
Appendix
16.1.2.7
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
8 Channel Digital Output Modules with Diagnostics and Input
Process Data
750-537
The digital output modules have a diagnostic bit for each output channel. When an
output fault condition occurs (i.e., overload, short circuit, or broken wire), a
diagnostic bit is set. The diagnostic data is mapped into the Input Process Image,
while the output control bits are in the Output Process Image.
Table 246: 8 Channel Digital Output Modules with Diagnostics and Input Process Data
Input Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Diagnostic Diagnostic Diagnostic Diagnostic Diagnostic Diagnostic Diagnostic Diagnostic
bit
bit
bit
bit
bit
bit
bit
bit
S8
S7
S6
S5
S4
S3
S2
S1
Channel 8 Channel 7 Channel 6 Channel 5 Channel 4 Channel 3 Channel 2 Channel 1
Diagnostic bit S = ‘0’
no Error
Diagnostic bit S = ‘1’
overload, short circuit, or broken wire
Output Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
controls
controls
controls
controls
controls
controls
controls
DO 8
DO 7
DO 6
DO 5
DO 4
DO 3
DO 2
Channel 8 Channel 7 Channel 6 Channel 5 Channel 4 Channel 3 Channel 2
16.1.2.8
Bit 0
controls
DO 1
Channel 1
16 Channel Digital Output Modules
750-1500, -1501, -1504, -1505
Table 247: 16 Channel Digital Output Modules
Output Process Image
Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
control control control control control
control control control control control control control control control
controls
controls
s
s DO
s
s
s
s
s
s
s
s
s
s
s
s
DO 16
DO 10
DO 15 14 DO 13 DO 12 DO 11
DO 9 DO 8 DO 7 DO 6 DO 5 DO 4 DO 3 DO 2 DO 1
Channel
Channel
Channe Channe Channe Channe Channe
Channe Channe Channe Channe Channe Channe Channe Channe Channe
16
10
l 15
l 14
l 13
l 12
l 11
l9
l8
l7
l6
l5
l4
l3
l2
l1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
16.1.2.9
Appendix
343
8 Channel Digital Input/Output Modules
750-1502, -1506
Table 248: 8 Channel Digital Input/Output Modules
Input Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Data bit
Data bit
Data bit
Data bit
Data bit
Data bit
Data bit
Data bit
DI 8
DI 7
DI 6
DI 5
DI 4
DI 3
DI 2
DI 1
Channel 8 Channel 7 Channel 6 Channel 5 Channel 4 Channel 3 Channel 2 Channel 1
Output Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
controls
controls
controls
controls
controls
controls
controls
DO 8
DO 7
DO 6
DO 5
DO 4
DO 3
DO 2
Channel 8 Channel 7 Channel 6 Channel 5 Channel 4 Channel 3 Channel 2
Pos : 86.5 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Bit 0
controls
DO 1
Channel 1
344
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 86.6 /Serie 750 (WAGO-I/O-SYST EM)/Proz ess abbild Mapping/PFC xxx/750- 82xx Proz ess abbild - AIs-Ei nleitung (INTEL, mit word-alignment) @ 16\mod_1379574306413_21.doc x @ 132018 @ 3 @ 1
16.1.3
Analog Input Modules
The analog input modules provide 16-bit measured data and 8 control/status bits
per channel.
The controller only uses the 8 control/status bits internally for
configuration/parameterization (e.g., via WAGO-I/O-CHECK).
Therefore, only the 16-bit measurement values for each channel are in Intel
format and are mapped by word in the input process image for the controller.
Pos : 86.7 /Serie 750 (WAGO-I/O-SYST EM)/Proz ess abbild Mapping/Sofer n in dem Knoten auc h Digitalei ngangs kl emmen g estec kt, z u AIs @ 8\mod_1279112061364_21.doc x @ 59903 @ @ 1
When digital input modules are also present in the node, the analog input data is
always mapped into the Input Process Image in front of the digital data.
Pos : 86.8 /Serie 750 (WAGO-I/O-SYST EM)/Proz ess abbild Mapping/Infor mation - Infor mationen zum Steuer-/Statusbyteaufbau @ 4\mod_1238055708743_21.doc x @ 29070 @ @ 1
Information on the structure of control and status bytes
For detailed information on the structure of a particular I/O module’s
control/status bytes, please refer to that module’s manual. Manuals for each
module can be found on the Internet at www.wago.com.
Pos : 86.9 /Serie 750 (WAGO-I/O-SYST EM)/Proz ess abbild Mapping/ETHERN ET - EtherN et/IP - MOD BUS/TCP/PA ETHERN ET - AIs (Intel , mit word- alignment) @ 7\mod_1272352054685_21.doc x @ 55790 @ 4444 @ 1
16.1.3.1
1 Channel Analog Input Modules
750-491, (and all variations)
Table 249: 1 Channel Analog Input Modules
Input Process Image
Byte Destination
Offset
High Byte
Low Byte
0
D1
D0
1
D3
D2
16.1.3.2
Description
Measured Value UD
Measured Value Uref
2 Channel Analog Input Modules
750-452, -454, -456, -461, -462, -465, -466, -467, -469, -472, -474, -475, 476, 477, -478, -479, -480, -481, -483, -485, -492, (and all variations),
753-452, -454, -456, -461, -465, -466, -467, -469, -472, -474, -475, 476, -477,
478, -479, -483, -492, (and all variations)
Table 250: 2 Channel Analog Input Modules
Input Process Image
Byte Destination
Offset
High Byte
Low Byte
0
D1
D0
1
D3
D2
Description
Measured Value Channel 1
Measured Value Channel 2
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
16.1.3.3
Appendix
345
4 Channel Analog Input Modules
750-450, -453, -455, -457, -459, -460, -468, (and all variations),
753-453, -455, -457, -459
Table 251: 4 Channel Analog Input Modules
Input Process Image
Byte Destination
Offset
High Byte
Low Byte
0
D1
D0
1
D3
D2
2
D5
D4
3
D7
D6
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Description
Measured Value Channel 1
Measured Value Channel 2
Measured Value Channel 3
Measured Value Channel 4
346
Appendix
16.1.3.4
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
3-Phase Power Measurement Module
750-493
The above Analog Input Modules have a total of 9 bytes of user data in both the
Input and Output Process Image (6 bytes of data and 3 bytes of control/status).
The following tables illustrate the Input and Output Process Image, which has a
total of 6 words mapped into each image.
Word alignment is applied.
Table 252: 3-Phase Power Measurement Module
Input Process Image
Byte Destination
Offset
High Byte
Low Byte
0
S0
1
D1
D0
2
S1
3
D3
D2
4
S2
5
D5
D4
Description
Status byte 0
Input data word 1
Status byte 1
Input data word 2
Status byte 2
Input data word 3
Output Process Image
Offset
0
1
2
3
4
5
Byte Destination
High Byte
D1
D3
D5
Low Byte
C0
D0
C1
D2
C2
D4
Description
Control byte 0
Output data word 1
Control byte 1
Output data word 2
Control byte 2
Output data word 3
Pos : 86.10 /Serie 750 ( WAGO-I/O-SYST EM)/Pr ozessabbild M appi ng/ETH ERNET - EtherNet/IP - M ODBU S/TC P/PA ETH ERN ET - MOD BU S/TC P z us ätzlic h 8- Kanal AIs @ 15\mod_1370947457096_21.doc x @ 122444 @ 4 @ 1
16.1.3.5
8 Channel Analog Input Modules
750-451
Table 253: 8 Channel Analog Input Modules
Input Process Image
Byte Destination
Offset
High Byte
Low Byte
0
D1
D0
1
D3
D2
2
D5
D4
3
D7
D6
4
D9
D8
5
D11
D10
6
D13
D12
7
D15
D14
Description
Measured Value Channel 1
Measured Value Channel 2
Measured Value Channel 3
Measured Value Channel 4
Measured Value Channel 5
Measured Value Channel 6
Measured Value Channel 7
Measured Value Channel 8
Pos : 86.11 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
347
Pos : 86.12 /Serie 750 ( WAGO-I/O-SYST EM)/Pr ozessabbild M appi ng/PFC xxx/750-82xx Pr ozessabbild - AOs-Einl eitung (Intel, mi t word-alignment) @ 16\mod_1379574334273_21.doc x @ 132022 @ 3 @ 1
16.1.4
Analog Output Modules
The analog output modules provide 16-bit output values and 8 control/status bits
per channel.
The controller only uses the 8 control/status bits internally for
configuration/parameterization (e.g., via WAGO-I/O-CHECK).
Therefore, only the 16-bit measurement values for each channel are in Intel
format and are mapped by word in the output process image for the controller.
Pos : 86.13 /Serie 750 ( WAGO-I/O-SYST EM)/Pr ozessabbild M appi ng/Sofern i n dem Knoten auc h Digital ausgangs kl emmen g estec kt sind, zu AOs @ 8\mod_1279112179255_21.doc x @ 59906 @ @ 1
When digital output modules are also present in the node, the analog output data
is always mapped into the Output Process Image in front of the digital data.
Pos : 86.14 /Serie 750 ( WAGO-I/O-SYST EM)/Pr ozessabbild M appi ng/Informati on - Informati onen z um Steuer-/Status byteaufbau @ 4\mod_1238055708743_21.doc x @ 29070 @ @ 1
Information on the structure of control and status bytes
For detailed information on the structure of a particular I/O module’s
control/status bytes, please refer to that module’s manual. Manuals for each
module can be found on the Internet at www.wago.com.
Pos : 86.15 /Serie 750 ( WAGO-I/O-SYST EM)/Pr ozessabbild M appi ng/ETH ERNET - EtherNet/IP - M ODBU S/TC P/PA ETH ERN ET - AOs (INTEL, mit word-alignment) @ 7\mod_1272352309632_21.doc x @ 55793 @ 44 @ 1
16.1.4.1
2 Channel Analog Output Modules
750-550, -552, -554, -556, -560, -562, 563, -585, (and all variations),
753-550, -552, -554, -556
Table 254: 2 Channel Analog Output Modules
Output Process Image
Byte Destination
Offset
High Byte
Low Byte
0
D1
D0
1
D3
D2
16.1.4.2
Description
Output Value Channel 1
Output Value Channel 2
4 Channel Analog Output Modules
750-553, -555, -557, -559,
753-553, -555, -557, -559
Table 255: 4 Channel Analog Output Modules
Output Process Image
Byte Destination
Offset
High Byte
Low Byte
0
D1
D0
1
D3
D2
2
D5
D4
3
D7
D6
Pos : 86.16 /D okumentati on allgemei n/Gli ederungsel emente/---Seitenwec hs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Description
Output Value Channel 1
Output Value Channel 2
Output Value Channel 3
Output Value Channel 4
348
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 86.17 /Serie 750 ( WAGO-I/O-SYST EM)/Pr ozessabbild M appi ng/ETH ERNET - EtherNet/IP - M ODBU S/TC P/PA ETH ERN ET - Sonder kl emmen (Intel, mit wor d-alignment) bis KN X-Bus kl emme-für 32- Bit'er @ 7\mod_1272352385583_21.doc x @ 55796 @ 344444444444444444 @ 1
16.1.5
Specialty Modules
WAGO has a host of Specialty I/O modules that perform various functions. With
individual modules beside the data bytes also the control/status byte is mapped in
the process image.
The control/status byte is required for the bidirectional data exchange of the
module with the higher-ranking control system. The control byte is transmitted
from the control system to the module and the status byte from the module to the
control system.
This allows, for example, setting of a counter with the control byte or displaying
of overshooting or undershooting of the range with the status byte.
The control/status byte always is in the process image in the Low byte.
Information to the structure of the Control/Status byte
For detailed information about the structure of a particular module’s control/status
byte, please refer to that module’s manual. Manuals for each module can be found
on the Internet under: www.wago.com.
16.1.5.1
Counter Modules
750-404, (and all variations except of /000-005),
753-404, (and variation /000-003)
The above Counter Modules have a total of 5 bytes of user data in both the Input
and Output Process Image (4 bytes of counter data and 1 byte of control/status).
The counter value is supplied as 32 bits. The following tables illustrate the Input
and Output Process Image, which has a total of 3 words mapped into each image.
Word alignment is applied.
Table 256: Counter Modules 750-404, (and all variations except of /000-005),
753-404, (and variation /000-003)
Input Process Image
Byte Destination
Offset
Description
High Byte
Low Byte
0
S
Status byte
1
D1
D0
Counter value
2
D3
D2
Output Process Image
Offset
0
1
2
Byte Destination
High Byte
D1
D3
Low Byte
C
D0
D2
Description
Control byte
Counter setting value
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
349
750-404/000-005
The above Counter Modules have a total of 5 bytes of user data in both the Input
and Output Process Image (4 bytes of counter data and 1 byte of control/ status).
The two counter values are supplied as 16 bits. The following tables illustrate the
Input and Output Process Image, which has a total of 3 words mapped into each
image. Word alignment is applied.
Table 257: Counter Modules 750-404/000-005
Input Process Image
Byte Destination
Offset
High Byte
Low Byte
0
S
1
D1
D0
2
D3
D2
Description
Status byte
Counter Value of Counter 1
Counter Value of Counter 2
Output Process Image
Offset
0
1
2
Byte Destination
High Byte
Low Byte
C
D1
D0
D3
D2
Description
Control byte
Counter Setting Value of Counter 1
Counter Setting Value of Counter 2
750-638,
753-638
The above Counter Modules have a total of 6 bytes of user data in both the Input
and Output Process Image (4 bytes of counter data and 2 bytes of control/status).
The two counter values are supplied as 16 bits. The following tables illustrate the
Input and Output Process Image, which has a total of 4 words mapped into each
image. Word alignment is applied.
Table 258: Counter Modules 750-638, 753-638
Input Process Image
Byte Destination
Offset
High Byte
Low Byte
0
S0
1
D1
D0
2
S1
3
D3
D2
Description
Status byte von Counter 1
Counter Value von Counter 1
Status byte von Counter 2
Counter Value von Counter 2
Output Process Image
Offset
0
1
2
3
Byte Destination
High Byte
Low Byte
C0
D1
D0
C1
D3
D2
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Description
Control byte von Counter 1
Counter Setting Value von Counter 1
Control byte von Counter 2
Counter Setting Value von Counter 2
350
Appendix
16.1.5.2
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pulse Width Modules
750-511, (and all variations /xxx-xxx)
The above Pulse Width modules have a total of 6 bytes of user data in both the
Input and Output Process Image (4 bytes of channel data and 2 bytes of control/
status). The two channel values are supplied as 16 bits. Each channel has its own
control/status byte. The following table illustrates the Input and Output Process
Image, which has a total of 4 words mapped into each image. Word alignment is
applied.
Table 259: Pulse Width Modules 750-511, /xxx-xxx
Input and Output Process
Byte Destination
Offset
High Byte
Low Byte
0
C0/S0
1
D1
D0
2
C1/S1
3
D3
D2
16.1.5.3
Description
Control/Status byte of Channel 1
Data Value of Channel 1
Control/Status byte of Channel 2
Data Value of Channel 2
Serial Interface Modules with alternative Data Format
750-650, (and the variations /000-002, -004, -006, -009, -010, -011, -012, -013),
750-651, (and the variations /000-001, -002, -003),
750-653, (and the variations /000-002, -007),
753-650, -653
The process image of the / 003-000-variants depends on the parameterized
operating mode!
With the freely parameterizable variations /003 000 of the serial interface
modules, the desired operation mode can be set. Dependent on it, the process
image of these modules is then the same, as from the appropriate variation.
The above Serial Interface Modules with alternative data format have a total of 4
bytes of user data in both the Input and Output Process Image (3 bytes of serial
data and 1 byte of control/status). The following table illustrates the Input and
Output Process Image, which have a total of 2 words mapped into each image.
Word alignment is applied.
Table 260: Serial Interface Modules with alternative Data Format
Input and Output Process Image
Byte Destination
Offset
High Byte
Low Byte
0
D0
C/S
1
D2
D1
Description
Control/status
byte
Data bytes
Data byte
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
16.1.5.4
Appendix
351
Serial Interface Modules with Standard Data Format
750-650/000-001, -014, -015, -016
750-653/000-001, -006
The above Serial Interface Modules with Standard Data Format have a total of 6
bytes of user data in both the Input and Output Process Image (5 bytes of serial
data and 1 byte of control/status). The following table illustrates the Input and
Output Process Image, which have a total of 3 words mapped into each image.
Word alignment is applied.
Table 261: Serial Interface Modules with Standard Data Format
Input and Output Process Image
Byte Destination
Offset
High Byte
Low Byte
16.1.5.5
0
D0
C/S
1
2
D2
D4
D1
D3
Description
Data byte
Control/status
byte
Data bytes
Data Exchange Module
750-654, (and the variation /000-001)
The Data Exchange modules have a total of 4 bytes of user data in both the Input
and Output Process Image. The following tables illustrate the Input and Output
Process Image, which has a total of 2 words mapped into each image.
Word alignment is applied.
Table 262: Data Exchange Module
Input and Output Process Image
Byte Destination
Offset
High Byte
Low Byte
0
D1
D0
1
D3
D2
16.1.5.6
Description
Data bytes
SSI Transmitter Interface Modules
750-630 (and all variations)
The process image of the / 003-000-variants depends on the parameterized
operating mode!
The operating mode of the configurable /003-000 I/O module versions can be set.
Based on the operating mode, the process image of these I/O modules is then the
same as that of the respective version.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
352
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
The above SSI Transmitter Interface modules have a total of 4 bytes of user data
in the Input Process Image, which has 2 words mapped into the image.
Word alignment is applied.
Table 263: SSI Transmitter Interface Modules
Input Process Image
Byte Destination
Offset
High Byte
Low Byte
0
D1
D0
1
D3
D2
16.1.5.7
Description
Data bytes
Incremental Encoder Interface Modules
750-631/000-004, -010, -011
The above Incremental Encoder Interface modules have 5 bytes of input data and
3 bytes of output data. The following tables illustrate the Input and Output Process
Image, which have 4 words into each image. Word alignment is applied.
Table 264: Incremental Encoder Interface Modules 750-631/000-004, --010, -011
Input Process Image
Byte Destination
Offset
Description
High Byte
Low Byte
0
S
not used
Status byte
1
D1
D0
Counter word
2
not used
3
D4
D3
Latch word
Output Process Image
Offset
0
1
2
3
Byte Destination
High Byte
Low Byte
C
D1
D0
-
Description
not used
Control byte
Counter setting word
not used
not used
750-634
The above Incremental Encoder Interface module has 5 bytes of input data (6
bytes in cycle duration measurement mode) and 3 bytes of output data. The
following tables illustrate the Input and Output Process Image, which has 4 words
mapped into each image. Word alignment is applied.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
353
Table 265: Incremental Encoder Interface Modules 750-634
Input Process Image
Byte Destination
Offset
Description
High Byte
Low Byte
0
S
not used
Status byte
1
D1
D0
Counter word
2
(D2) *)
not used
(Periodic time)
3
D4
D3
Latch word
*)
If cycle duration measurement mode is enabled in the control byte, the cycle duration is
given as a 24-bit value that is stored in D2 together with D3/D4.
Output Process Image
Offset
0
1
2
3
Byte Destination
High Byte
Low Byte
C
D1
D0
-
Description
not used
Control byte
Counter setting word
not used
750-637
The above Incremental Encoder Interface Module has a total of 6 bytes of user
data in both the Input and Output Process Image (4 bytes of encoder data and 2
bytes of control/status). The following table illustrates the Input and Output
Process Image, which have 4 words mapped into each image. Word alignment is
applied.
Table 266: Incremental Encoder Interface Modules 750-637
Input and Output Process Image
Byte Destination
Offset
High Byte
Low Byte
0
C0/S0
1
D1
D0
2
C1/S1
3
D3
D2
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Description
Control/Status byte of Channel 1
Data Value of Channel 1
Control/Status byte of Channel 2
Data Value of Channel 2
354
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
750-635,
753-635
The above Digital Pulse Interface module has a total of 4 bytes of user data in
both the Input and Output Process Image (3 bytes of module data and 1 byte of
control/status). The following table illustrates the Input and Output Process
Image, which have 2 words mapped into each image. Word alignment is applied.
Table 267: Digital Pulse Interface Modules 750-635
Input and Output Process Image
Byte Destination
Offset
High Byte
Low Byte
16.1.5.8
0
D0
C0/S0
1
D2
D1
Description
Control/status
byte
Data bytes
Data byte
DC-Drive Controller
750-636
The DC-Drive Controller maps 6 bytes into both the input and output process
image. The data sent and received are stored in up to 4 input and output bytes
(D0 ... D3). Two control bytes (C0, C1) and two status bytes (S0/S1) are used to
control the I/O module and the drive.
In addition to the position data in the input process image (D0 … D3), it is
possible to display extended status information (S2 … S5). Then the three control
bytes (C1 … C3) and status bytes (S1 … S3) are used to control the data flow.
Bit 3 of control byte C1 (C1.3) is used to switch between the process data and the
extended status bytes in the input process image (Extended Info_ON). Bit 3 of
status byte S1 (S1.3) is used to acknowledge the switching process.
Table 268: DC-Drive Controller 750-636
Input Process Image
Byte Destination
Offset
High Byte
Low Byte
0
S1
S0
*)
**)
1
D1*) / S3**)
D0*) / S2**)
2
D3*) / S5**)
D2*) / S4**)
Description
Status byte S1
Actual position*)
/ Extended status
byte S3**)
Actual position
(MSB) /
Extended status
byte S3**)
Status byte S0
Actual position
(LSB) / Extended
status byte S2**)
Actual position*)
/ Extended status
byte S4**)
ExtendedInfo_ON = ‘0’.
ExtendedInfo_ON = ‘1’.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
355
Output Process Image
Offset
0
16.1.5.9
Byte Destination
High Byte
Low Byte
C1
C0
1
D1
D0
2
D3
D2
Description
Control byte C1 Control byte C0
Setpoint position Setpoint position
(LSB)
Setpoint position Setpoint position
(MSB)
Stepper Controller
750-670
The Stepper controller RS422 / 24 V / 20 mA 750-670 provides the fieldbus
coupler 12 bytes input and output process image via 1 logical channel. The data to
be sent and received are stored in up to 7 output bytes (D0 … D6) and 7 input
bytes (D0 … D6), depending on the operating mode.
Output byte D0 and input byte D0 are reserved and have no function assigned.
One I/O module control and status byte (C0, S0) and 3 application control and
status bytes (C1 ... C3, S1 ... S3) provide the control of the data flow.
Switching between the two process images is conducted through bit 5 in the
control byte (C0 (C0.5). Activation of the mailbox is acknowledged by bit 5 of the
status byte S0 (S0.5).
Table 269: Stepper Controller RS 422 / 24 V / 20 mA 750-670
Input Process Image
Byte Destination
Offset
High Byte
Low Byte
0
reserved
S0
1
D1
D0
2
D3
D2
3
D5
D4
4
5
*)
**)
S3
D6
S1
S2
Cyclic process image (Mailbox disabled)
Mailbox process image (Mailbox activated)
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Description
reserved
Status byte S0
Process data*) / Mailbox**)
Status byte S3
Status byte S1
Process data*) /
reserved**)
Status byte S2
356
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Output Process Image
Byte Destination
High Byte
Low Byte
reserved
C0
D1
D0
D3
D2
D5
D4
Offset
0
1
2
3
4
5
*)
**)
C3
D6
C1
C2
Cyclic process image (Mailbox disabled)
Mailbox process image (Mailbox activated)
Description
reserved
Control byte C0
Process data*) / Mailbox**)
Process data*) /
reserved**)
Control byte C1 Control byte C2
Control byte C3
16.1.5.10 RTC Module
750-640
The RTC Module has a total of 6 bytes of user data in both the Input and Output
Process Image (4 bytes of module data and 1 byte of control/status and 1 byte ID
for command). The following table illustrates the Input and Output Process
Image, which have 3 words mapped into each image. Word alignment is applied.
Table 270: RTC Module 750-640
Input and Output Process Image
Byte Destination
Offset
High Byte
Low Byte
0
ID
C/S
1
2
D1
D3
D0
D2
Description
Command byte
Control/status
byte
Data bytes
16.1.5.11 DALI/DSI Master Module
750-641
The DALI/DSI Master module has a total of 6 bytes of user data in both the Input
and Output Process Image (5 bytes of module data and 1 byte of control/status).
The following tables illustrate the Input and Output Process Image, which have 3
words mapped into each image. Word alignment is applied.
Table 271: DALI/DSI Master Module 750-641
Input Process Image
Byte Destination
Offset
High Byte
Low Byte
0
D0
S
1
D2
D1
2
D4
D3
Description
DALI Response
Status byte
Message 3
DALI Address
Message 1
Message 2
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
357
Output Process Image
Offset
Byte Destination
High Byte
Low Byte
0
D0
C
1
2
D2
D4
D1
D3
Description
DALI command,
DSI dimming value
Parameter 2
Command extension
Control byte
DALI Address
Parameter 1
16.1.5.12 DALI Multi-Master Module
753-647
The DALI Multi-Master module occupies a total of 24 bytes in the input and
output range of the process image.
The DALI Multi-Master module can be operated in "Easy" mode (default) and
"Full" mode. "Easy" mode is used to transmit simply binary signals for lighting
control. Configuration or programming via DALI master module is unnecessary
in "Easy" mode.
Changes to individual bits of the process image are converted directly into DALI
commands for a pre-configured DALI network. 22 bytes of the 24-byte process
image can be used directly for switching of electronic ballasts (ECG), groups or
scenes in "Easy" mode. Switching commands are transmitted via DALI and group
addresses, where each DALI and each group address is represented by a 2-bit pair.
The structure of the process data is described in detail in the following tables.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
358
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 272: Overview of Input Process Image in the "Easy" Mode
Input process image
Byte designation
Offset
Note
High byte
Low byte
res.
Status, activate broadcast
Bit 0: 1-/2-button mode
0
S
Bit 2: Broadcast status ON/OFF
Bit 1,3-7: 1
DA4…DA7
DA0…DA3
Bitpaar für DALI-Adresse DA0:
2
DA12…DA15
DA8…DA11
Bit 1: Bit set = ON
3
DA20…DA23
DA16…DA19
Bit not set = OFF
4
DA28…DA31
DA24…DA27
Bit 2: Bit set = Error
5
DA36…DA39
DA32…DA35
Bit not set = No error
6
DA44…DA47
DA40…DA43
Bit pairs DA1 … DA63 similar to DA0.
7
DA52…DA55
DA48…DA51
8
DA60…DA63
DA56…DA59
Bit pair for DALI group address GA0:
9
GA4…GA7
GA0…GA3
Bit 1: Bit set = ON
Bit not set = OFF
Bit 2: Bit set = Error
10
GA12…GA15
GA8…GA11
Bit not set = No error
Bit pairs GA1 … GA15 similar to GA0.
11
Not in use
DA = DALI address
GA = Group address
Table 273: Overview of the Output Process Image in the "Easy" Mode“
Output process image
Byte designation
Offset
Note
High byte
Low byte
res. Broadcast ON/OFF and activate:
Bit 0: Broadcast ON
Bit 1: Broadcast OFF
0
S
Bit 2: Broadcast ON/OFF/dimming
Bit 3: Broadcast short ON/OFF
Bits 4 … 7: reserved
1
DA4…DA7
DA0…DA3
Bit pair for DALI address DA0:
2
DA12…DA15
DA8…DA11
Bit 1: short: DA switch ON
3
DA20…DA23
DA16…DA19
long: dimming, brighter
4
DA28…DA31
DA24…DA27
Bit 2: short: DA switch OFF
5
DA36…DA39
DA32…DA35
long: dimming, darker
6
DA44…DA47
DA40…DA43
Bit pairs DA1 … DA63 similar to DA0.
7
DA52…DA55
DA48…DA51
8
DA60…DA63
DA56…DA59
Bitpaar für DALI-Gruppenadresse GA0:
9
GA4…GA7
GA0…GA3
Bit 1: short: GA switch ON
long: dimming, brighter
Bit 2: short: GA switch OFF
10
GA12…GA15
GA8…GA11
long: dimming, darker
Bit pairs GA1 … GA15 similar to GA0.
11
Bit 8…15
Bit 0…7
Switch scene 0…15
DA = DALI address
GA = Group address
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
359
16.1.5.13 LON® FTT Module
753-648
The process image of the LON® FTT module consists of a control/status byte and
23 bytes of bidirectional communication data that is processed by the
WAGO-I/O-PRO function block "LON_01.lib". This function block is essential
for the function of the LON® FTT module and provides a user interface on the
control side.
16.1.5.14 EnOcean Radio Receiver
750-642
The EnOcean radio receiver has a total of 4 bytes of user data in both the Input
and Output Process Image (3 bytes of module data and 1 byte of control/status).
The following tables illustrate the Input and Output Process Image, which have 2
words mapped into each image. Word alignment is applied.
Table 274: EnOcean Radio Receiver 750-642
Input Process Image
Byte Destination
Offset
High Byte
Low Byte
0
D0
S
1
D2
D1
Description
Data byte
Status byte
Data bytes
Output Process Image
Offset
0
1
High Byte
-
Byte Destination
Low Byte
C
-
Description
not used
Control byte
not used
16.1.5.15 MP Bus Master Module
750-643
The MP Bus Master Module has a total of 8 bytes of user data in both the Input
and Output Process Image (6 bytes of module data and 2 bytes of control/status).
The following table illustrates the Input and Output Process Image, which have 4
words mapped into each image. Word alignment is applied.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
360
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 275: MP Bus Master Module 750-643
Input and Output Process Image
Byte Destination
Offset
High Byte
Low Byte
0
C1/S1
C0/S0
1
2
3
D1
D3
D5
D0
D2
D4
Description
extended
Control/
Status byte
Control/status
byte
Data bytes
16.1.5.16 Bluetooth® RF-Transceiver
750-644
The size of the process image for the Bluetooth® module can be adjusted to 12, 24
or 48 bytes.
It consists of a control byte (input) or status byte (output); an empty byte; an
overlay able mailbox with a size of 6, 12 or 18 bytes (mode 2); and the Bluetooth®
process data with a size of 4 to 46 bytes.
Thus, each Bluetooth® module uses between 12 and 48 bytes in the process image.
The sizes of the input and output process images are always the same.
The first byte contains the control/status byte; the second contains an empty byte.
Process data attach to this directly when the mailbox is hidden. When the mailbox
is visible, the first 6, 12 or 18 bytes of process data are overlaid by the mailbox
data, depending on their size. Bytes in the area behind the optionally visible
mailbox contain basic process data. The internal structure of the Bluetooth®
process data can be found in the documentation for the Bluetooth® 750-644 RF
Transceiver.
The mailbox and the process image sizes are set with the startup tool WAGO-I/OCHECK.
Table 276: Bluetooth® RF-Transceiver 750-644
Input and Output Process Image
Byte Destination
Offset
High Byte
Low Byte
0
-
C0/S0
1
2
3
...
max.
23
D1
D3
D5
...
D0
D2
D4
...
D45
D44
Description
not used
Control/status
byte
Mailbox (0, 3, 6 or 9 words) and
Process data (2-23 words)
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
361
16.1.5.17 Vibration Velocity/Bearing Condition Monitoring VIB I/O
750-645
The Vibration Velocity/Bearing Condition Monitoring VIB I/O has a total of 12
bytes of user data in both the Input and Output Process Image (8 bytes of module
data and 4 bytes of control/status). The following table illustrates the Input and
Output Process Image, which have 8 words mapped into each image.
Word alignment is applied.
Table 277: Vibration Velocity/Bearing Condition Monitoring VIB I/O 750-645
Input and Output Process Image
Byte Destination
Offset
Description
High Byte
Low Byte
Control/status byte
0
C0/S0
not used
(log. Channel 1,
Sensor input 1)
Data bytes
1
D1
D0
(log. Channel 1, Sensor input 1)
Control/status byte
2
C1/S1
not used
(log. Channel 2,
Sensor input 2)
Data bytes
3
D3
D2
(log. Channel 2, Sensor input 2)
Control/status byte
4
C2/S2
not used
(log. Channel 3,
Sensor input 1)
Data bytes
5
D5
D4
(log. Channel 3, Sensor input 3)
Control/status byte
6
C3/S3
not used
(log. Channel 4,
Sensor input 2)
Data bytes
7
D7
D6
(log. Channel 4, Sensor input 2)
Pos : 86.18 /Serie 750 ( WAGO-I/O-SYST EM)/Pr ozessabbild M appi ng/ETH ERNET - EtherNet/IP - M ODBU S/TC P/PA ETH ERN ET - MOD BU S/TC P T eil 1 KN X/EIB/TP1-Kl emme 753-646 (nur für 750-830, - 842, -849) @ 5\mod_1253540550198_21.doc x @ 41890 @ 4 @ 1
16.1.5.18 KNX/EIB/TP1 Module
753-646
The KNX/TP1 module appears in router and device mode with a total of 24-byte
user data within the input and output area of the process image, 20 data bytes and
2 control/status bytes. Even though the additional bytes S1 or C1 are transferred
as data bytes, they are used as extended status and control bytes. The opcode is
used for the read/write command of data and the triggering of specific functions
of the KNX/EIB/TP1 module. Word-alignment is used to assign 12 words in the
process image. Access to the process image is not possible in router mode.
Telegrams can only be tunneled.
In device mode, access to the KNX data can only be performed via special
function blocks of the IEC application. Configuration using the ETS engineering
tool software is required for KNX.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
362
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 278: KNX/EIB/TP1 Module 753-646
Input Process Image
Byte Destination
Offset
High Byte
Low Byte
0
S0
1
S1
OP
2
3
4
5
6
7
8
9
10
11
D1
D3
D5
D7
D9
D11
D13
D15
D17
D19
D0
D2
D4
D6
D8
D10
D12
D14
D16
D18
Description
not used
extended
Status byte
Data byte 1
Data byte 3
Data byte 5
Data byte 7
Data byte 9
Data byte 11
Data byte 13
Data byte 15
Data byte 17
Data byte 19
Status byte
Opcode
Data byte 0
Data byte 2
Data byte 4
Data byte 6
Data byte 8
Data byte 10
Data byte 12
Data byte 14
Data byte 16
Data byte 18
Output Process Image
Offset
0
Byte Destination
High Byte
Low Byte
C0
1
C1
OP
2
3
4
5
6
7
8
9
10
11
D1
D3
D5
D7
D9
D11
D13
D15
D17
D19
D0
D2
D4
D6
D8
D10
D12
D14
D16
D18
Description
not used
extended
Control byte
Data byte 1
Data byte 3
Data byte 5
Data byte 7
Data byte 9
Data byte 11
Data byte 13
Data byte 15
Data byte 17
Data byte 19
Control byte
Opcode
Data byte 0
Data byte 2
Data byte 4
Data byte 6
Data byte 8
Data byte 10
Data byte 12
Data byte 14
Data byte 16
Data byte 18
Pos : 86.19 /Serie 750 ( WAGO-I/O-SYST EM)/Pr ozessabbild M appi ng/ETH ERNET - EtherNet/IP - M ODBU S/TC P/PA ETH ERN ET - MOD BU S/TC P T eil 2 ASI- und Sys temkl emmen ( 750-342, - 830, -842, -849) @ 5\mod_1246540791017_21.doc x @ 36540 @ 434 @ 1
16.1.5.19 AS-interface Master Module
750-655
The length of the process image of the AS-interface master module can be set to
fixed sizes of 12, 20, 24, 32, 40 or 48 bytes.
It consists of a control or status byte, a mailbox with a size of 0, 6, 10, 12 or 18
bytes and the AS-interface process data, which can range from 0 to 32 bytes.
The AS-interface master module has a total of 6 to maximally 24 words data in
both the Input and Output Process Image. Word alignment is applied.
The first Input and output word, which is assigned to an AS-interface master
module, contains the status / control byte and one empty byte.
Subsequently the mailbox data are mapped, when the mailbox is permanently
superimposed (Mode 1).
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
363
In the operating mode with suppressible mailbox (Mode 2), the mailbox and the
cyclical process data are mapped next.
The following words contain the remaining process dat.
The mailbox and the process image sizes are set with the startup tool WAGO-I/OCHECK.
Table 279: AS-interface Master Module 750-655
Input and Output Process Image
Byte Destination
Offset
High Byte
Low Byte
0
-
C0/S0
1
2
3
...
max.
23
D1
D3
D5
...
D0
D2
D4
...
D45
D44
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Description
not used
Control/status
byte
Mailbox (0, 3, 5, 6 or 9 words)/
Process data (0-16 words)
364
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
16.1.6
System Modules
16.1.6.1
System Modules with Diagnostics
750-610, -611
The modules provide 2 bits of diagnostics in the Input Process Image for
monitoring of the internal power supply.
Table 280: System Modules with Diagnostics 750-610, -611
Input Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Diagnostic
bit S 2
Fuse
Bit 0
Diagnostic
bit S 1
Fuse
Pos : 86.20 /Serie 750 ( WAGO-I/O-SYST EM)/Pr ozessabbild M appi ng/ETH ERNET - EtherNet/IP - M ODBU S/TC P/PA ETH ERN ET - MOD BU S/TC P T eil 3 Bi när e Platzhalter klemmen - letzte Kl emme @ 8\mod_1279182270905_21.doc x @ 60020 @ 4 @ 1
16.1.6.2
Binary Space Module
750-622
The Binary Space Modules behave alternatively like 2 channel digital input
modules or output modules and seize depending upon the selected settings 1, 2, 3
or 4 bits per channel. According to this, 2, 4, 6 or 8 bits are occupied then either in
the process input or the process output image.
Table 281: Binary Space Module 750-622 (with Behavior Like 2 Channel Digital Input)
Input and Output Process Image
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
(Data bit
(Data bit
(Data bit
(Data bit
(Data bit
(Data bit
Data bit
DI 8)
DI 7)
DI 6)
DI 5)
DI 4)
DI 3)
DI 2
Bit 0
Data bit
DI 1
Pos : 87 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
365
Pos : 88.1 /Serie 750 (WAGO-I/O-SYST EM)/Anhang/PFC xxx/COD ESYS- 2-Bi bliothekenAnhang 750-82xx COD ESYS- 2-Bi bliotheken - Ü berschrift 2 + Einl eitung @ 14\mod_1361269527935_21.doc x @ 112310 @ 2 @ 1
16.2
CODESYS 2 Libraries
Additional functions for the controller 750-8202/040-000are provided using
libraries.
Pos : 88.2 /Serie 750 (WAGO-I/O-SYST EM)/Anhang/PFC xxx/COD ESYS- 2-Bi bliothekenAnhang 750-82xx Allgemeine Bibliotheken - Ü bersc hrift 3 + Ei nleitung @ 14\mod_1361269742703_21.doc x @ 112314 @ 3 @ 1
16.2.1
General Libraries
This section contains general CODESYS libraries supported by the controller7508202/040-000.
Pos : 88.3 /Serie 750 (WAGO-I/O-SYST EM)/Anhang/PFC xxx/COD ESYS- 2-Bi bliothekenAnhang 750-82xx Unterstützte F kt. CODESYS-Sys Li bs @ 16\mod_1379416835341_21.doc x @ 131652 @ 4 @ 1
16.2.1.1
CODESYS System Libraries
All of the functions of the CODESYS system libraries listed below are supported.
Table 282: CODESYS System Libraries
Library
Analyzation.lib
AnalyzationNew.lib
Iecsfc.lib
Function
Analysis of boolean expressions
Analysis of boolean expressions
Provision of implicit variables in
the SFC (sequential function chart)
NetVarUdp_LIB_V23.lib Implementation for network
variables
Standard.LIB
Offers various standard functions
SysLibAlarmTrend.lib
Supports alarm and trend tasks
SysLibCallback.lib
For installing call-back handlers
and event handlers
SysLibDir.lib
For accessing directories
SysLibDirect.lib
Access to variables using indices
SysLibEvent.lib
Handling of events in the system
SysLibFileStream.lib
File handling using ANSI-C
functions
SysLibGetAddress.lib
Returns addresses and the size of
memory segments
SysLibIecTasks.lib
Administration of IEC tasks
SysLibMem.lib
Memory administration
SysLibPlcCtrl.lib
Control of the PLC from outside
the PLC program
SysLibProjectInfo.lib
Reading out of information about
the CODESYS project
SysLibSem.lib
Handling of semaphores
SysLibSockets.lib
Socket handling
SysLibSocketsAsync.lib Socket handling, asynchronous
SysLibStr.lib
String functions
SysLibTasks.lib
Administration of tasks
SysLibTime.lib
Administration of real-time clock
SysLibVisu.lib
Dynamic visualization
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
C/IEC 61131
C and IEC 61131
C and IEC 61131
IEC 61131
IEC 61131
C
IEC 61131
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
366
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 282: CODESYS System Libraries
Library
SysTaskInfo.lib
Util.lib
Util_no_Real.lib
Function
Evaluation of task information in
the Online mode
Various logical operations
Various logical operations
C/IEC 61131
IEC 61131
IEC 61131
IEC 61131
Additional information about the libraries is given in the online Help function for
CODESYS-IDE.
Pos : 88.4 /Serie 750 (WAGO-I/O-SYST EM)/Anhang/PFC xxx/COD ESYS- 2-Bi bliothekenAnhang 750-82xx Unterstützte F kt. Sys LibC om.lib @ 16\mod_1379591498880_21.doc x @ 132210 @ 4 @ 1
</dg_
16.2.1.2
SysLibCom.lib
The controller 750-8202/040-000supports the following function blocks of the
“SysLibCom.lib” library:
-
SysComClose
SysComGetVersion2300
SysComOpen
SysComRead
SysComSetSettings
SysComSetSettingsEx
SysComWrite
Observe restrictions on the settings for stop bits!
The setting “1.5 stop bits” is not supported by controller750-8202/040-000.
Additional information about this is given in the online Help function for
CODESYS-IDE.
Pos : 88.5 /Serie 750 (WAGO-I/O-SYST EM)/Anhang/PFC xxx/COD ESYS- 2-Bi bliothekenAnhang 750-82xx Unterstützte F kt. Sys LibFile.lib @ 16\mod_1376650313666_21.doc x @ 129168 @ 4 @ 1
16.2.1.3
SysLibFile.lib
The controller 750-8202/040-000supports the following function blocks of the
“SysLibFile.lib” library:
-
SysFileClose
SysFileCopy
SysFileDelete
SysFileEOF
SysFileGetPos
SysFileGetSize
SysFileGetTime
SysFileOpen
SysFileRead
SysFileRename
SysFileSetPos
SysFileWrite
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
367
Ensure that files are saved!
Files are not reliably saved on the data medium until you call up the
“SysFileClose” function block!
Additional information about this is given in the online Help function for
CODESYS-IDE.
Pos : 88.6 /Serie 750 (WAGO-I/O-SYST EM)/Anhang/PFC xxx/COD ESYS- 2-Bi bliothekenAnhang 750-82xx Unterstützte F kt. Sys LibFile.lib, SysLi bFileAs ync.li b - Erg änz ung Parameter @ 21\mod_1421153928414_21.doc x @ 171308 @ @ 1
Notes on the parameters of the function blocks
File and directory names distinguish between upper and lower case!
“test.txt”≠ “TEST.TXT”≠ “Test.txt”
The separator for directories is: “/.”
The file system supports:
-
Absolute paths, (e.g., “/media/sd/test.txt”)
Relative paths (e.g., “testpath/test.txt”)
Macros (e.g., “HOME://”, “CARD://”, “TMP://”)
Table 283: Possible Macros for File Access
Macro
HOME://
CARD://
TMP://
Booting from Internal Memory
“/home/codesys/”
(internal NAND memory)
“/media/sd/”
(nemory card)
“/tmp/codesys/”
(internal RAM memory)
Booting from Memory Card
“/home/codesys/”
(memory card)
“/home/codesys/”
(memory card)
“/tmp/codesys/”
(internal RAM memory)
Pos : 88.7 /Serie 750 (WAGO-I/O-SYST EM)/Anhang/PFC xxx/COD ESYS- 2-Bi bliothekenAnhang 750-82xx Unterstützte F kt. Sys LibFileAs ync.li b @ 16\mod_1379593093035_21.doc x @ 132226 @ 4 @ 1
16.2.1.4
SysLibFileAsync.lib
The controller 750-8202/040-000supports the following function blocks of the
“SysLibFileAsync.lib” library:
-
SysFileCloseAsync
SysFileCopyAsync
SysFileDeleteAsync
SysFileEOFAsync
SysFileGetPosAsync
SysFileGetSizeAsync
SysFileGetTimeAsync
SysFileOpenAsync
SysFileReadAsync
SysFileRenameAsync
SysFileSetPosAsync
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
368
Appendix
-
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
SysFileWriteAsync
Ensure that files are saved!
Files are not reliably saved to the data medium until you call up the
“SysFileCloseAsync” function block.
Additional information about this is given in the online Help function for
CODESYS-IDE.
Pos : 88.8 /Serie 750 (WAGO-I/O-SYST EM)/Anhang/PFC xxx/COD ESYS- 2-Bi bliothekenAnhang 750-82xx Unterstützte F kt. Sys LibFile.lib, SysLi bFileAs ync.li b - Erg änz ung Parameter @ 21\mod_1421153928414_21.doc x @ 171308 @ @ 1
Notes on the parameters of the function blocks
File and directory names distinguish between upper and lower case!
“test.txt”≠ “TEST.TXT”≠ “Test.txt”
The separator for directories is: “/.”
The file system supports:
-
Absolute paths, (e.g., “/media/sd/test.txt”)
Relative paths (e.g., “testpath/test.txt”)
Macros (e.g., “HOME://”, “CARD://”, “TMP://”)
Table 284: Possible Macros for File Access
Macro
HOME://
CARD://
TMP://
Booting from Internal Memory
“/home/codesys/”
(internal NAND memory)
“/media/sd/”
(nemory card)
“/tmp/codesys/”
(internal RAM memory)
Booting from Memory Card
“/home/codesys/”
(memory card)
“/home/codesys/”
(memory card)
“/tmp/codesys/”
(internal RAM memory)
Pos : 88.9 /Serie 750 (WAGO-I/O-SYST EM)/Anhang/PFC xxx/COD ESYS- 2-Bi bliothekenAnhang 750-82xx Unterstützte F kt. Sys LibRtc.lib @ 16\mod_1379592856080_21.doc x @ 132222 @ 4 @ 1
16.2.1.5
SysLibRtc.lib
The controller 750-8202/040-000supports the following function blocks of the
“SysLibRtc.lib” library:
-
SysRtcGetHourMode
SysRtcGetTime
SysRtcSetTime
Additional information about this is given in the online Help function for
CODESYS-IDE.
Pos : 88.10 /Serie 750 ( WAGO-I/O-SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibli othekenAnhang 750- 82xx U nterstützte F kt. BusDiag.li b @ 14\mod_1361269924018_21.doc x @ 112325 @ 4 @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
16.2.1.6
Appendix
369
BusDiag.lib
The controller 750-8202/040-000 supports the following function blocks of the
“BusDiag.lib” library:
-
DiagGetBusState
DiagGetState
The document containing a description of this library and the function blocks it
includes is available for download on the Internet at www.wago.com.
Pos : 88.11.1 /Serie 750 ( WAGO-I/O- SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibliotheken/BusDi ag.lib - D evic eNumber/Anhang 750-8xxx U nterstützte F kt. BusDiag.li b - D eviceN umber - Ei nleitung @ 23\mod_1434525621487_21.doc x @ 183899 @ @ 1
The values for the input variables “DEVICENUMBER” of the
“DiagGetBusState” and “DiagGetState” functions are based on the particular
device and bus system and are as follows for the controller “PFC200 CS 2ETH
RS /XTR” (750-8202/040-000):
Pos : 88.11.2 /Serie 750 ( WAGO-I/O- SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibliotheken/BusDi ag.lib - D evic eNumber/Anhang 750-8xxx U nterstützte F kt. BusDiag.li b - D eviceN umber 0 ... 1 (KB, M B) @ 16\mod_1376550646887_21.doc x @ 129001 @ @ 1
Table 285: Input Variable “DEVICENUMBER”
Bus System
Internal data bus
MODBUS
Value
0
1
Pos : 88.12 /Serie 750 ( WAGO-I/O-SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibli othekenAnhang 750- 82xx U nterstützte F kt. mod_com.lib @ 16\mod_1379592185513_21.doc x @ 132218 @ 4 @ 1
16.2.1.7
mod_com.lib
The controller 750-8202/040-000supports the following function blocks of the
“mod_com.lib” library:
-
ADD_PI_INFORMATION
CRC16
FBUS_ERROR_INFORMATION
GET_DIGITAL_INPUT_OFFSET
GET_DIGITAL_OUTPUT_OFFSET
KBUS_ERROR_INFORMATION
MOD_COM_VERSION
PI_INFORMATION
SET_DIGITAL_INPUT_OFFSET
SET_DIGITAL_OUTPUT_OFFSET
SLAVE_ADDRESS
The document containing a description of this library and the function blocks it
includes is available for download on the Internet at www.wago.com.
Pos : 88.13 /Serie 750 ( WAGO-I/O-SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibli othekenAnhang 750- 82xx U nterstützte F kt. SerComm.li b @ 16\mod_1379592049403_21.doc x @ 132214 @ 4 @ 1
16.2.1.8
SerComm.lib
The controller 750-8202/040-000supports the following function blocks of the
“SerComm.lib” library:
-
SERCOMM
SERCOMM_VERSION
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
370
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
The document containing a description of this library and the function blocks it
includes is available for download on the Internet at www.wago.com.
Pos : 88.14 /Serie 750 ( WAGO-I/O-SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibli othekenAnhang 750- 82xx U nterstützte F kt. WagoC onfigToolLIB.lib - Einl eitung @ 21\mod_1422351625348_21.doc x @ 172738 @ 4 @ 1
16.2.1.9
WagoConfigToolLIB.lib
The following table shows call-ups that allow you to configure and parameterize
the controller from the PLC program or Linux® via the “ConfigToolFB” function
block (see parameter “stCallString”). In addition to WBM and the CBM, this is
another variant to configure the controller for operational requirements.
The configuration directory for this under Linux® is: /etc/config-tools/
Figure 115: Graphical Representation of the “ConfigToolFB” Function Block
Pos : 88.15.1 /Serie 750 ( WAGO-I/O- SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibliotheken/Wag oConfigTool LIB.lib - Skripte/Anhang 750-82xx U nterstütz te F kt. Wag oConfigTool LIB.lib - Skripte Informati on @ 21\mod_1422351719833_21.doc x @ 172742 @ @ 1
Table 286: Description of the Configuration Scripts for “Information”
Parameters Status Call-Up
Output/Input
Effective
Controller Details: Identifies various information about the controller
Product
get_coupler_details
read
Product description
Immediately
Description
product-description
get_coupler_details
Order Number read
Item number of the controller Immediately
order-number
Firmware
get_coupler_details
Firmware version of the
read
Immediately
Revision
firmware-revision
controller
Licence
get_coupler_details
read
CODESYS license details
Immediately
Information
license-information
Network Details X1: Identifies the parameters currently used for the ETHERNET interface
X1/X2 in “switched” mode or for the ETHERNET interface X1 in “separated” mode
Status of the interface.
Possible return values:
get_actual_eth_config
State
read
Immediately
- enabled
X1 state
- disabled
get_actual_eth_config
Mac Address
read
Display of the MAC address Immediately
X1 mac-address
get_actual_eth_config
IP Address
read
Display of current IP address Immediately
X1 ip-address
get_actual_eth_config
Display of the current subnet
Subnet Mask
read
Immediately
X1 subnet-mask
mask
Network Details X2: Identifies the parameters currently used for the ETHERNET interface
X2 in “separated” mode
See “Network Details X1”. When calling these up, replace “X1” with “X2” (in “separated” mode
only).
Pos : 88.15.2 /Serie 750 ( WAGO-I/O- SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibliotheken/Wag oConfigTool LIB.lib - Skripte/Anhang 750-82xx U nterstütz te F kt. Wag oConfigTool LIB.lib - Skripte COD ESYS, >= F W06 @ 23\mod_1441184955756_21.doc x @ 190659 @ @ 1
</dg_
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
371
Table 287: Description of the Configuration Scripts for “CODESYS”
Parameters Status Call
Output/Input
Effecti
ve
Information
CODESYS
Webserver
read
Version
Project Details
Version of the CODESYS
Webserver
Immedia
tely
Display of the project
information specified in
CODESYS (Menu > Project >
Project Information)
Immedia
tely
Immedia
tely
Immedia
tely
Immedia
tely
Immedia
tely
Display of the CODESYS status
(RUN or STOP)
Immedia
tely
Date
read
Title
read
Version
read
Author
read
Description
read
get_coupler_details
codesys-Webserverversion
get_rts_info
project date
get_rts_info
project title
get_rts_info
project version
get_rts_info
project author
get_rts_info
project description
CODESYS State
get_rts_info
state
Home Directory (Boot Project Location)
State
read
read
get_runtime_config
homedir-on-sdcard
write
config_runtime
homedir-onsdcard=<Wert>
Home
Directory
(Boot Project
Location)
Pos : 88.15.3 /Serie 750 ( WAGO-I/O- SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibliotheken/Wag oConfigTool LIB.lib - Skripte/Anhang 750-82xx U nterstütz te F kt. Wag oConfigTool LIB.lib - Skripte Networ ki ng - Host/D omai n, >= F W04 @ 21\mod_1422353373228_21.doc x @ 172778 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Storage logation for the home
directory.
Possible return values:
- enabled: The home directory
is on the SD card.
- disabled: The home directory
is on the boot medium.
After
restart
Storage logation for the home
directory.
Possible entries for the value are:
- enabled: Put the home
directory on the SD card.
- disabled: The home directory
is on the boot medium.
372
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 288: Description of the Configuration Scripts for “Networking - Host/Domain Name”
Parameters Status Call
Output/Input
Effecti
ve
Host Name
Host Name
Actual
Hostname
read
get_coupler_details
hostname
write
change_hostname
hostname=<String>
read
get_coupler_details
actual-hostname
Display of the host name.
The return value is blank when
/etc/hostname is empty.
For details see the parameter
“Actual Hostname.”
Changing the host name.
Input a host name for <String>.
The actual host name (if
/etc/hostname is empty, a unique
host name is generated from the
MAC address)
Immedia
tely
Immedia
tely
Immedia
tely
Domain Name
Domain name
read
write
get_coupler_details
domain-name
change_hostname
dnsdomain=<String>
Display of domain name
Change the domain name. Enter
the domain name for <String>.
Immedia
tely
Pos : 88.15.4 /Serie 750 ( WAGO-I/O- SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibliotheken/Wag oConfigTool LIB.lib - Skripte/Anhang 750-82xx U nterstütz te F kt. Wag oConfigTool LIB.lib - Skripte Networ ki ng - TCP/IP, >= F W04 @ 21\mod_1422353781296_21.doc x @ 172794 @ @ 1
Table 289: Description of the Configuration Scripts for “Networking - TCP/IP”
Parameters Status Call
Output/Input
Effecti
ve
IP Address X1: Determines the IP parameters of the ETHERNET interfaces X1/X2 in
“switched” mode and the ETHERNET interface X1 in “separated” mode
Path via which the interface
receives its IP address
Possible return values are:
get_eth_config
read
- static (set statically)
X1 config-type
- dhcp (per DHC)
Type of IP
- bootp (per BootP)
Immedia
address
tely
Enable
process,
via
which
the
configuration
config_interfaces
interface receives its IP address
interface=X1
Possible entries for <Value> are:
write
- static (set statically)
config-type=<Value>
- dhcp (per DHC)
state=enabled
- bootp (per BootP)
get_eth_config
Address set for using a static IP
read
X1 ip-address
address (static IP).
Change IP address for static IP
Immedia
IP address
config_interfaces
<Value> must have an IP address tely
write
interface=X1
with the format
ip-address=<Value>
“Number.Number.Number.Numb
er.”
get_eth_config
Subnet mask set for using a static
read
X1 subnet-mask
IP address (static IP)
Change subnet mask for static IP Immedia
Subnet Mask
config_interfaces
addresses. <Value> must have an tely
write
interface=X1
IP address with the format
subnet-mask=<Value>
“Number.Number.Number.Numb
er.”
IP Address X2: Determines the parameters currently used for the ETHERNET interface X2
in “separated” mode
See “IP Address X1.” When calling these up, replace X1 with X2 (only permissible in “separated”
mode).
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
373
Table 289: Description of the Configuration Scripts for “Networking - TCP/IP”
Parameters Status Call
Output/Input
Effecti
ve
Default Gateway 1
Default
Gateway
read
write
read
Default
Gateway
Default
Gateway
get_default_gateway_
config number=1 state
config_default_gateway
number=1
state=<stateval>
get_default_gateway_
config number=1 value
write
config_default_gateway
number=1 value=<gw>
read
get_default_gateway_
config number=1 metric
write
config_default_gateway
number=1 metric=<n>
Current status of the default
gateway 1.
Possible return values:
enabled
disabled
Possible entries for <Value>:
enabled
disabled
Current IP address of the default
gateway 1
Enter the IP address of the
default gateway 1 here.
<gw> is an IP address with the
format “Number. Number.
Number. Number.”
Current metric (cost factor) of the
default gateway 1
The default value is “20.”
Enter the metric of the default
gateway 1 here.
<n> is a number between “0” and
“4.294.967.295.”
Default Gateway 2
See “Default Gateway 1.” When calling the gateway number, replace 1 with 2.
DNS Server 1
DNS server address with the
read
get_dns_server 1
consecutive number 1
Set the address of the DNS server
edit_dns_server
with 1 as the consecutive
dns-server-nr=1
number.
write/
<Value> is an IP address with the
change=change
DNS Server 1 change
format
dns-server“Number.Number.Number.Numb
name=<Value>
er.”
edit_dns_server
write/
Delete the DNS server with the
dns-server-nr=1
delete
consecutive number 1.
delete=delete
DNS Server 2 … n
See “DNS Server 1.” When calling, adjust the server number (2 … n).
Add DNS Server
Add additional DNS addresses
here.
edit_dns_server add=add
Add DNS
<Value> is an IP address with the
dns-serverwrite
format
server
name=<Value>
“Number.Number.Number.Numb
er.”
Pos : 88.15.5 /Serie 750 ( WAGO-I/O- SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibliotheken/Wag oConfigTool LIB.lib - Skripte/Anhang 750-82xx U nterstütz te F kt. Wag oConfigTool LIB.lib - Skripte Networ ki ng - ETH ERN ET @ 21\mod_1422354094451_21.doc x @ 172798 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Immedia
tely
Immedia
tely
Immedia
tely
Immedia
tely
Immedia
tely
374
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 290: Description of the Configuration Scripts for “Networking - ETHERNET”
Parameters Status Call-Up
Output/Input
Effective
Query the switch
configuration:
Possible return values:
- 0 = „switched“ mode
- 1 = „separated“ mode
Set the switch configuration:
Possible entries for <value>:
- 0 = „switched“ mode
- 1 = „separated“ mode
Immediately
Switch Configuration
read
get_dsa_mode
Interface Mode
write
set_dsa_mode -v
<value>
read
get_eth_config
X1 state
Interface X1
Port State
write
read
Autonegotiation
write
read
read
Speed and
Duplex Settings
write
Query the port state:
Possible return values:
- enabled
- disabled
Immediately
config_ethernet port=X1
Activate port: enabled
state=enabled
config_ethernet port=X1
Deactivate port: disabled
state=disabled
Query the status of the
autonegotiation function:
get_eth_config
Possible return values:
X1 autoneg
- on
- off
config_ethernet port=X1 Activate the autonegotiation
autoneg=on
function: on
Deactivate the
autonegotiation function: off
Note: You must also indicate Immediately
the speed and duplex value
config_ethernet port=X1 when you deactivate the
autoneg=off
autonegotiation function.
speed=<value>
Possible entries for speed:
- 10M
duplex=<value>
- 100M
Possible entries for duplex:
- half
- full
get_eth_config
Display of ETHERNET speed
X1 speed
get_eth_config
Display of the Duplex mode
X1 duplex
Change the ETHERNET
speed and the Duplex mode. Immediately
config_ethernet port=X1 Possible entries for speed:
- 10M
autoneg=off
- 100M
speed=<value>
Possible entries for duplex:
duplex=<value>
- half
- full
Interface X2
See “Interface X1”. When calling these up, replace “X1” with “X2”.
Pos : 88.15.6 /Serie 750 ( WAGO-I/O- SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibliotheken/Wag oConfigTool LIB.lib - Skripte/Anhang 750-82xx U nterstütz te F kt. Wag oConfigTool LIB.lib - Skripte NTP, >= F W04 @ 21\mod_1422354363992_21.doc x @ 172816 @ @ 1
</dg_
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
375
Table 291: Description of the Configuration Scripts for “NTP”
Parameters Status Call
Configuration Data
read
get_ntp_config
state
write
config_sntp
state=<Value>
State
Port
read
write
read
get_ntp_config
time-server-<N>
write
config_sntp
time-server<N>=<Value>
read
get_ntp_config
update-time
write
config_sntp
update-time=<Value>
Time Server
Update Time
(seconds)
get_ntp_config
port
config_sntp
port=<Value>
Pos : 88.15.7 /Serie 750 ( WAGO-I/O- SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibliotheken/Wag oConfigTool LIB.lib - Skripte/Anhang 750-82xx U nterstütz te F kt. Wag oConfigTool LIB.lib - Skripte CLOCK @ 21\mod_1422354512622_21.doc x @ 172820 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Output/Input
Query the status of the NTP
server
Possible return values are:
- enabled
- disabled
Possible entries for <Value>:
- enabled
- disabled
Port number of the NTP server
Enter the port number for
<Value>.
Query the IP address of the time
server: N = 1 … 4 for querying
one of 4 time servers.
Enter the IP address of 4 time
servers
<N> can be a value from 1 to 4.
<Value> is an IP address with
the format “Number. Number.
Number. Number.”
Query the time in seconds
between two requests to the time
server.
Specify the time-server's query
cycle (in s) for <Value>.
Effecti
ve
Immedi
ately
Immedi
ately
Immedi
ately
Immedi
ately
376
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 292: Description of the Configuration Scripts for “Clock”
Parameters Status Call-Up
Clock
Time and Date
Date on device,
local
Time on
device, UTC
Time on
device, local
read
write
read
write
read
write
Output/Input
get_clock_data
date-local
config_clock
type=local
date=<Datum>
get_clock_data
time-utc
config_clock
type=utc time=<Time>
get_clock_data
time-local
config_clock
type=local
time=<Time>
read
get_clock_data
display-mode
write
config_clock _
display_mode
display-mode=<value>
read
get_clock_data
tz-string
write
config_timezone
tz-string=<String>
12-HourFormat
Time Zone
TZ-String
Effective
Local time and date
Change date. The format for
<date> is: DD.MM.YYYY
Immediately
Time/UTC
Change time, based on UTC
time. The format for <time>
is: hh:mm:ss xx
Immediately
Time/local time
Change time, based on local Immediately
time. The format for <time>
is: hh:mm:ss xx
Presentation format either as
12 or 24-hour format:
Possible return values:
- 12-hour-format
- 24-hour-format
Immediately
Set the presentation format
for the time.
Possible entries for <Value>:
- 12-hour-format
- 24-hour-format
Currently set time zone –
original TZ string as stored in
the operating system.
Immediately
Change TZ string directly.
Example of <String>:
CET-1CEST,
M3.5.0/2,M10.5.0/3
Pos : 88.15.8 /Serie 750 ( WAGO-I/O- SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibliotheken/Wag oConfigTool LIB.lib - Skripte/Anhang 750-82xx U nterstütz te F kt. Wag oConfigTool LIB.lib - Skripte Admin, mit R S-232, >= F W06 @ 23\mod_1436517573514_21.doc x @ 185958 @ @ 1
Table 293: Description of the Configuration Scripts for "Administration"
Parameters Status Call
Output/Input
Administration
Configuration of Serial Interface
Configuration
of serial
interface
read
write
get_coupler_details
RS232-owner
config_RS232
owner=<value>
User of the serial interface
Possible return values are:
- Linux
- None
User of the serial interface
Possible entries for <value> are:
- Linux
- None
Effecti
ve
immedia
tely
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
377
Table 293: Description of the Configuration Scripts for "Administration"
Parameters Status Call
Output/Input
Configuration of Service Interface
read
Configuration
of Service
Interface
write
Reboot Controller
-
write
Effecti
ve
User of the serial interface.
Possible return values are:
- service (WAGO-I/OCHECK, WAGO-I/O-PRO,
get_service_interface_
e!COCKPIT)
config mode
- linux (Linux® console)
- free (unused, free for
application)
User of the serial interface.
Possible entries for <value>:
config_service_interface
- service
_config mode=<value>
- linux
- free
immedia
tely
start_reboot
immedia
tely
Restart the controller.
Pos : 88.15.9 /Serie 750 ( WAGO-I/O- SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibliotheken/Wag oConfigTool LIB.lib - Skripte/Anhang 750-82xx U nterstütz te F kt. Wag oConfigTool LIB.lib - Skripte Pac kage Ser ver @ 21\mod_1422363351901_21.doc x @ 172851 @ @ 1
</dg_
Table 294: Description of Configuration Scripts for “Package Server”
Parameters Status Call-Up
Firmware Update
Medium for
active partition
read
Create
firmware
backup
write
Output/Input
Specifies the medium for the
get_filesystem_data
active partition
active-partition-medium
(memory card, internal flash).
Generates a backup of the
selected packet on the specified
medium.
Parameter:
firmware_backup
<Value1> = 1, if “Settings”
packagepacket is to be selected.
settings=<Value1>
<Value2> = 1, if the “CODESYS
packageProject” packet is to be selected.
codesys=<Value2>
<Value3> = 1, if the “System”
packagepacket is to be selected.
system=<Value3>
<Value4> = Target medium for
devicesaving the backup.
medium=<Value4>
(memory card, internal flash)
auto-update=<Value5> <Value5> = 1, if Auto Update is
to be activated.
Parameters, which are not to be
set (1) can either be set to 0 or
omitted completely.
Pos : 88.15.10 /Seri e 750 ( WAGO-I/O-SYSTEM)/Anhang/PFC xxx/COD ESYS-2-Bi bliotheken/WagoC onfigToolLIB.li b - Skripte/Anhang 750- 82xx U nterstützte F kt. WagoC onfigToolLIB.li b - Skripte Ports/Ser vic es - N etwor k Servic es @ 21\mod_1422363598600_21.doc x @ 172855 @ @ 1
</dg_
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Valid
Right
away
Right
away
378
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 295: Description of Configuration Scripts for “Ports and Services” – “Network Services
Parameters Status Call-Up
Network Services
Telnet
read
get_port_state
telnet
write
config_port
port=telnet
state=<Value>
Telnet Port
FTP
read
config_ssl
ftp-status
write
config_port
port=ftp state=<Value>
FTP Port
FTPS
read
config_ssl ftps-status
write
config_port port=ftps
state=<Value>
FTPS Port
HTTP
read
config_ssl http-status
write
config_port port=http
state=<Value>
HTTP Port
HTTPS
read
config_ssl https-status
HTTPS Port
write
config_port port=https
state=<Value>
Output/Input
Valid
Read the status of the Telnet
server.
Possible return values:
- enabled
- disabled
Possible entries for <Value>:
- enabled
- disabled
Right
away
Read the status of the FTP
server.
Possible return values:
- enabled
- disabled
Possible entries for <Value>:
- enabled
- disabled
Right
away
Read the status of the FTPS port.
Possible return values:
- enabled
- disabled
Right
away
Activate/Deactivate FTPS.
Possible entries for <Value>:
- enabled
- disabled
Read the status of the HTTP port.
Possible return values:
- enabled
- disabled
Right
away
Activate/Deactivate HTTP.
Possible entries for <Value>:
- enabled
- disabled
Read the status of the HTTPS
port.
Possible return values:
- enabled
- disabled
Activate/Deactivate HTTPS.
Possible entries for <Value>:
- enabled
- disabled
Right
away
Pos : 88.15.11 /Seri e 750 ( WAGO-I/O-SYSTEM)/Anhang/PFC xxx/COD ESYS-2-Bi bliotheken/WagoC onfigToolLIB.li b - Skripte/Anhang 750- 82xx U nterstützte F kt. WagoC onfigToolLIB.li b - Skripte Ports/Ser vic es - PLC RT S, >= F W06 @ 24\mod_1445232402807_21.doc x @ 193838 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
379
Table 296: Description of Configuration Scripts for “Ports and Services” – “PLC Runtime Services”
Parameters Status Call
General Settings
read
PLC runtime
version
write
read
Boot project
location
write
read
Default web
page
write
Change
authentication
password
write
Output/Input
Version of the enabled PLC
runtime
Possible return values:
get_runtime_config
- 0 = no runtime enabled
running-version
- 2 = CODESYS 2 enabled
- 3 = e!RUNTIME enabled
Setting and, if necessary,
stopping of the previous runtime
version and starting of required
config_runtime runtime- version
Possible entries for <value>:
version=<value>
- 0 = do not enable runtime
- 2 = enable CODESYS2
- 3 = enable e!RUNTIME
Memory location for a boot
project of the runtime application
Possible return values:
get_runtime_config
- HOME:// (saving on internal
boot-project
memory)
- CARD:// (saving on the
memory card)
Possible entries for <value>:
- HOME:// (saving on internal
config_runtime bootmemory)
project=<value>
- CARD:// (saving on the
memory card)
Calling web page when only
entering the IP address in the
web browser
get_runtime_config
Possible return values:
default-webpage
- WBM (web based
management)
- Webvisu (web visualization)
Possible entries for <value>:
config_runtime default- - WBM (web based
management)
webpage=<value>
- Webvisu (web visualization)
config_linux_user
user=admin newChange the PLC runtime access
password=<value>
password
confirmpassword=<value>
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Effecti
ve
Immedi
ately
Immedi
ately
Immedi
ately
Immedi
ately
380
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 296: Description of Configuration Scripts for “Ports and Services” – “PLC Runtime Services”
Parameters Status Call
CODESYS 2 Settings
read
CODESYS2
Webserver
State
write
CODESYS2
Port
Authentication
read
write
CODESYS2
Service State
read
write
CODESYS2
Communicatio
n Port
read
write
Output/Input
Read status of the runtimeget_runtime_config cfg- specific Webserver
Possible return values:
version=2 Webserver- enabled
state
- disabled
Enable/disable runtime-specific
config_runtime cfgWebserver
version=2 WebserverPossible entries for <value>:
state=<value>
- enabled
- disabled
Read status of the port
authentication for
communication between the
get_runtime_config cfg- CODESYS 2 PC software and
version=2 authentication the controller
Possible return values:
- enabled
- disabled
config_runtime cfgPossible entries for <value>:
version=2
- enabled
authentication=<value> - disabled
Read status of the port for
communication between the
CODESYS 2 PC software and
get_runtime_config
the controller
service-state
Possible return values:
- enabled
- disabled
Possible entries for <value>:
config_runtime service- enabled
state=<value>
- disabled
Read value of set network port
for communication between PC
get_runtime_config
and controller
comm-port
Default value is 2455
Change port number
config_runtime commEnter the TCP/IP port number for
port=<value>
<value>.
Effecti
ve
Immedi
ately
Immedi
ately
Immedi
ately
Immedi
ately
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
381
Table 296: Description of Configuration Scripts for “Ports and Services” – “PLC Runtime Services”
Parameters Status Call
e!Runtime Settings
read
e!RUNTIME
Webserver
State
write
e!RUNTIME
Port
Authentication
read
write
Output/Input
Read status of the runtimeget_runtime_config cfg- specific Webserver
Possible return values
version=3 Webserver- enabled
state
- disabled
Enable/disable runtime-specific
config_runtime cfgWebserver
version=3 WebserverPossible entries for <value>:
state=<value>
- enabled
- disabled
Read status of the port
authentication for
communication between the
get_runtime_config cfg- e!COCKPIT PC software and the
version=3 authentication controller
Possible return values:
- enabled
- disabled
config_runtime cfgPossible entries for <value>:
version=3
- enabled
authentication= <value> - disabled
Pos : 88.15.12 /Seri e 750 ( WAGO-I/O-SYSTEM)/Anhang/PFC xxx/COD ESYS-2-Bi bliotheken/WagoC onfigToolLIB.li b - Skripte/Anhang 750- 82xx U nterstützte F kt. WagoC onfigToolLIB.li b - Skripte Ports/Ser vic es - SSH/TFT P @ 21\mod_1422363998124_21.doc x @ 172897 @ @ 1
</dg_
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Effecti
ve
Immedi
ately
Immedi
ately
382
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 297: Description of Configuration Scripts for “Ports and Services” – “SSH/TFTP”
Parameters Status Call-Up
Output/Input
SSH
SSH Server
SSH
read
get_ssh_config state
read
get_ssh_config rootaccess-state
read
get_ssh_config
password-request-state
read
get_ssh_config portnumber
write
config_ssh
state=<Value>
write
config_ssh portnumber=<Value>
write
config_ssh root-accessstate-value=<Value>
write
config_ssh passwordrequest-statevalue=<Value>
TFTP
TFTP Server
TFTP
read
get_tftp_config state
read
get_tftp_config
download-dir
write
config_tftp
state=<Value>
write
config_tftp downloaddir=<Value>
Read the status of the SSH port.
Possible return values:
- enabled
- disabled
Indicates whether logon as root is
permitted.
Possible return values:
- enabled
- disabled
Indicates whether authentication
by password (instead of PKI key
files) is permitted.
Possible return values:
- enabled
- disabled
Specifies the SSH port
Activate/Deactivate SSH service.
Possible entries for <Value>:
- enabled
- disabled
Valid
Right
away
Set the SSH port
Permit/Prohibit logon as root.
Possible entries for <Value>:
- enabled
- disabled
Permit/Prohibit authentication by
password.
Possible entries for <Value>:
- enabled
- disabled
Read the status of the TFTP port.
Possible return values:
- enabled
- disabled
Read the TFTP main directory.
Activate/Deactivate TFTP port.
Possible entries for <Value>:
- enabled
- disabled
Right
away
Set the TFTP main directory.
Pos : 88.15.13 /Seri e 750 ( WAGO-I/O-SYSTEM)/Anhang/PFC xxx/COD ESYS-2-Bi bliotheken/WagoC onfigToolLIB.li b - Skripte/Anhang 750- 82xx U nterstützte F kt. WagoC onfigToolLIB.li b - Skripte SNMP @ 21\mod_1422363766527_21.doc x @ 172879 @ @ 1
<
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
383
Table 298: Description of Configuration Scripts for “SNMP”
Parameters Status Call-Up
General SNMP information parameters
get_snmp_data
read
device-name
Name of device
config_snmp
write
device-name=<Value>
Output/Input
Valid
Specifies the SNMP parameter
Right
“sysName”.
away
Change the SNMP parameter
After
“sysName”
restart
*
(<Value> = string).
get_snmp_data
Specifies the SNMP parameter
Right
read
description
“sysDescr”.
away
Description
Change the SNMP parameter
After
config_snmp
write
“sysDescr”
restart
description=<Value>
*
(<Value> = string).
get_snmp_data
Specifies the SNMP
Right
read
physical-location
“sysLocation” parameter.
away
Physical
config_snmp
Change the SNMP parameter
location
After
write
physical“sysLocation”
restart
*
location=<Value>
(<Value> = string).
get_snmp_data
Specifies the SNMP
Right
read
contact
“sysContact” parameter.
away
Contact
Change the SNMP parameter
After
config_snmp
write
“sysContact”
restart
contact=<Value>
(<Value> = string).
*
When entering values, the blank characters must be filled by either “+” or “%20”. If this is not
done, the input is not recognized as a coherent string.
SNMP Manager configuration for v1 and v2c
Outputs the status of the SNMP
protocol for v1/v2c as a string.
Right
get_snmp_data
Protocol status read
Possible return values:
away
v1-v2c-state
- enabled
- disabled
Local
get_snmp_data
Specifies the community name
Right
Community
read
v1-v2c-communityset for v1/v2c/
away
Name
name
Activates/deactivates the v1/v2c
protocol (<Value1> = enabled or
disabled) and assigns a
community name. (<Value2> =
string without spaces, min. 1,
max. 32 characters).
config_snmp
Protocol
After
v1-v2c-state=<Value1>
Status/Commu write
Note:
restart
v1-v2c-communitynity Name
No community name is required
name=<Value2>
for deactivation.
Activation is only possible by
entering a community name. A
community name can only be
saved when the protocol is
activated.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
384
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 298: Description of Configuration Scripts for “SNMP”
Parameters Status Call-Up
Output/Input
Valid
SNMP Trap Receiver Configuration for v1 and v2c
Any number of trap receivers can be configured. A trap receiver that has been set up is always
active; the data set must be completely deleted to deactivate it.
Specifies the IP address of the
trap receiver that the controller is
to send the v1 or v2 traps to.
read
get_snmp_data
v1-v2c-trap-receiveraddress <Nummer>
Community
Name
read
get_snmp_data
v1-v2c-trap-receivercommunity-name
<Nummer>
Trap version
read
get_snmp_data
v1-v2c-trap-receiverversion <Nummer>
write
config_snmp
v1-v2c-trap-receiveredit=<Value1>
v1-v2c-trap-receiveraddress=<Value2>
v1-v2c-trap-receivercommunityname=<Value3>
v1-v2c-trap-receiverversion=<Value4>
IP address of a
trap receiver
Creating/
deleting a trap
receiver
The <number> parameter
enables consecutive reading of
related data from the individually
configured trap receiver for a
short period of time (without
interim changing of the data).
This is a consecutive number that
is not connected to the data. If
the number is not included, the
data of the first receiver are read.
Specifies the community name
that the SNMP agent of the
controller sends in the Trap
Header.
Parameter <number> see section
“IP Address of a Trap Receiver”.
Specifies the SNMP version
(“v1” or “v2c”) via which the
SNMP agent sends the traps to
the associated trap receiver
address.
Parameter <number> see section
“IP Address of a Trap Receiver”.
Create a new trap receiver
(value1=add) or delete an already
configured trap receiver
(value1=delete).
Right
away
Right
away
Right
away
Other parameters:
<Value2> = IP address
(number.number.number.number
) that the controller is to send the
traps to.
After
<Value3>: Community string
restart
(string), which the controller
enters in the trap header.
<Value4>: SNMP version, via
which the traps are sent (v1 or
v2c).
Note:
All parameters must also be
entered when deleting a trap
receiver, as this is the only means
to uniquely identify the data set.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
385
Table 298: Description of Configuration Scripts for “SNMP”
Parameters Status Call-Up
Output/Input
Valid
Configuration of SNMP v3
Any number of SNMP v3 users can be created. A user that has been set up is always active; the
complete data set must be deleted to deactivate a user.
Specifies the user name for the
v3 user.
The <number> parameter
enables consecutive reading of
the related data from the
get_snmp_data
individually configured trap
Authentication
Right
read
v3-auth-name
receiver for a short period of
Name
away
<Nummer>
time (without interim changing
of the data). This is a consecutive
number that is not connected to
the data. If the number is not
included, the data of the first user
are read.
Specifies the type of encryption
that the v3 user uses (none,
Authentication
Right
get_snmp_data
MD5, or SHA).
read
encryption type
away
v3-auth-type <Number>
Parameter <number> see
“Authentication Name”.
Specifies the key string for
Authentication
authentication.
Right
get_snmp_data
read
key
away
v3-auth-key <Nummer> Parameter <number> see
“Authentication Name”.
Specifies the type of privacy
encryption for the v3 user (none,
Privacy
Right
get_snmp_data
DES, or AES).
read
encryption type
away
v3-privacy <number>
Parameter <number> see
“Authentication Name”.
Specifies the key string for
privacy. If nothing is entered, the
get_snmp_data
Right
SNMP agent uses the
Privacy key
read
v3-privacy-key
away
“Authentication Key”.
<number>
Parameter <number> see
“Authentication Name”.
IP address of an SNMP manager
that the agent traps for this v3
get_snmp_data
user are sent to. If nothing is
Trap receiver
Right
read
v3-notification-receiver entered here, no traps are sent for
address
away
<number>
this user.
Parameter <number> see
“Authentication Name”.
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
386
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 298: Description of Configuration Scripts for “SNMP”
Parameters Status Call-Up
Add new v3User
write
Delete v3 user
write
Output/Input
Creating a new v3 user.
v3-auth-name: User name, string
without spaces, maximum of 32
characters. This must be a new,
unique user name.
Parameters:
User name (<Value1> = string)
Encryption method. (<Value2>
config_snmp
= none, MD5 or SHA).
v3-edit=add
Key string for authentication,
v3-auth(<Value3> = String with at least
name=<Value1>
eight and a maximum of 32
v3-auth-type=<Value2>
characters)
v3-auth-key=<Value3>
Privacy encryption method
v3-privacy=<Value4>
(<Value4> = none, DES or
v3-privacyAES).
key=<Value5>
Privacy key string (<Value5> =
v3-notificationString with at least eight and a
receiver=<Value6>
maximum of 32 characters), can
also be blank; in this case the
authentication key will be used.
The IP address of a trap receiver
is transmitted as the notification
receiver (<Value6> =
number.number.number.number)
. This parameter is not required if
no v3 traps are to be sent.
Deleting a v3 user that has been
set up.
Because the doubled allocation
config_snmp
of the same user name is
v3-edit=delete
prevented when creating a user,
v3-auth-name=<Value>
the name is sufficient to uniquely
identify a data set (<Value> =
string).
Valid
After
restart
After
restart
Pos : 88.16 /Serie 750 ( WAGO-I/O-SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibli othekenAnhang 750- 82xx U nterstützte F kt. WagoLi bCpuUs age.li b @ 16\mod_1379586976300_21.doc x @ 132116 @ 4 @ 1
16.2.1.10 WagoLibCpuUsage.lib
The controller 750-8202/040-000supports the following function blocks of the
“WagoLibCpuUsage.lib” library:
-
CPU_Usage
The document containing the description of the library and the function block it
includes is available for download on the Internet at www.wago.com.
Pos : 88.17 /Serie 750 ( WAGO-I/O-SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibli othekenAnhang 750- 82xx U nterstützte F kt. WagoLi bDiagnostic IDs.li b @ 16\mod_1379587275475_21.doc x @ 132150 @ 4 @ 1
16.2.1.11 WagoLibDiagnosticIDs.lib
The controller 750-8202/040-000supports the following function blocks of the
“WagoLibDiagnosticIDs.lib” library:
-
DIAGNOSTIC_SEND_ID
DIAGNOSTIC_SET_TEXT_FOR_ID
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
387
The document containing the description of the library and the function block it
includes is available for download on the Internet at www.wago.com.
Pos : 88.18 /Serie 750 ( WAGO-I/O-SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibli othekenAnhang 750- 82xx U nterstützte F kt. WagoLi bLed.lib @ 14\mod_1361272304970_21.doc x @ 112340 @ 4 @ 1
16.2.1.12 WagoLibLed.lib
The controller 750-8202/040-000supports the following function blocks of the
“WagoLibLed.lib” library:
-
LED_SET_STATIC
LED_SET_BLINK
LED_SET_FLASH
LED_SET_ERROR
LED_RESET_ERROR
LED_RESET_ALL_ERRORS
LED_GET_STATE
LED_GET_STATE_ASYNC
The document containing a description of this library and the function blocks it
includes is available for download on the Internet at www.wago.com.
Pos : 88.19 /Serie 750 ( WAGO-I/O-SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibli othekenAnhang 750- 82xx U nterstützte F kt. WagoLi bNetSnmp.lib @ 16\mod_1379590838521_21.doc x @ 132172 @ 4 @ 1
16.2.1.13 WagoLibNetSnmp.lib
The controller 750-8202/040-000supports the following function blocks of the
“WagoLibNetSnmp.lib” library:
-
snmpGetValueCustomOID_INT32
snmpGetValueCustomOID_STRING
snmpGetValueCustomOID_UINT32
snmpRegisterCustomOID_INT32
snmpRegisterCustomOID_STRING
snmpRegisterCustomOID_UINT32
snmpSetValueCustomOID_INT32
snmpSetValueCustomOID_STRING
snmpSetValueCustomOID_UINT32
The document containing the description of the library and the function block it
includes is available for download on the Internet at www.wago.com.
Pos : 88.20 /Serie 750 ( WAGO-I/O-SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibli othekenAnhang 750- 82xx U nterstützte F kt. WagoLi bNetSnmpM anager.li b @ 16\mod_1379589831733_21.doc x @ 132154 @ 4 @ 1
16.2.1.14 WagoLibNetSnmpManager.lib
The controller 750-8202/040-000supports the following function blocks of the
“WagoLibNetSnmpManager.lib” libraries:
-
SNMPM_DINT_TO_TLV
SNMPM_UDINT_TO_TLV
SNMPM_STRING_TO_TLV
SNMPM_TLV_TO_DINT
SNMPM_TLV_TO_UDINT
SNMPM_TLV_TO_STRING
SNMPM_GET
SNMPM_GET_V3
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
388
Appendix
-
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
SNMPM_SET
SNMPM_SET_V3
The document containing a description of this library and the function blocks it
includes is available for download on the Internet at www.wago.com.
Pos : 88.21 /Serie 750 ( WAGO-I/O-SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibli othekenAnhang 750- 82xx U nterstützte F kt. WagoLi bSSL.lib @ 16\mod_1379590244955_21.doc x @ 132168 @ 4 @ 1
16.2.1.15 WagoLibSSL.lib
The controller 750-8202/040-000supports the following function blocks of the
“WagoLibSSL.lib” library:
-
SSL_CTX
SSL_CTX_load_verify_locations
SSL_CTX_sess_set_cache_size
SSL_CTX_set_client_CA_list
SSL_CTX_set_method
SSL_CTX_use_certificate_file
SSL_CTX_use_PrivateKey_file
SSL_free
SSL_get_error
SSL_Hndshk_Accept
SSL_Hndshk_Connect
SSL_load_client_CA_file
SSL_read
SSL_shutdown
SSL_write
The document containing a description of this library and the function blocks it
includes is available for download on the Internet at www.wago.com.
Pos : 88.22 /Serie 750 ( WAGO-I/O-SYST EM)/Anhang/PFC xxx/C ODESYS-2- Bibli othekenAnhang 750- 82xx U nterstützte F kt. WagoLi bTer minalDiag.li b @ 16\mod_1379591082409_21.doc x @ 132176 @ 4 @ 1
16.2.1.16 WagoLibTerminalDiag.lib
The controller 750-8202/040-000supports the following function blocks of the
“WagoLibTerminalDiag.lib” library:
-
GET_TERMINALDIAG
The document containing a description of this library and the function blocks it
includes is available for download on the Internet at www.wago.com.
Pos : 89 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Appendix
389
Pos : 90.1 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/Ebene 2Ü bersic ht Open-Source- Pakete und - Liz enz en - Ü bersc hrift 2 @ 24\mod_1447656904368_21.doc x @ 195638 @ 2 @ 1
16.3
Overview of Open Source Packages and Licenses
Pos : 90.2 /All e Seri en ( Allgemei ne Module)/Open-Sourc e-Softwareliz enzen/Ü bersicht Open- Source- Pakete und -Liz enzen - Einl eitung @ 25\mod_1453449798134_21.doc x @ 198974 @ @ 1
The following table contains an overview of the software packages and related
license terms.
Pos : 90.3 /All e Seri en ( Allgemei ne Module)/Open-Sourc e-Softwareliz enzen/Ü bersicht Open- Source- Pakete und -Liz enzen - T abell e @ 24\mod_1447150990124_21.doc x @ 195228 @ @ 1
Table 299: Overview of Open Source Licenses
Software
Version
Url
Package
barebox
2014.11.0
http://www.barebox.org/download/barebox2014.11.0.tar.bz2
bash
3.2.48
http://ftp.uni-kl.de/pub/gnu/bash/bash3.2.48.tar.gz
bootpc
0.64
http://www.sfr-fresh.com/linux/misc/bootpc0.64.tar.gz
busybox
1.20.2
http://www.busybox.net/downloads/busybox1.20.2.tar.bz2
coreutils
8.19
http://ftp.uni-kl.de/pub/gnu/coreutils/coreutils8.19.tar.xz
cpufrequtils 007
http://www.kernel.org/pub/linux/utils/kernel/cpuf
req/cpufrequtils-007.tar.bz2
daemonize 1.4
http://www.pengutronix.de/software/ptxdist/temp
orary-src/daemonize-1.4.tar.gz
dbus
1.6.8
http://dbus.freedesktop.org/releases/dbus/dbus1.6.8.tar.gz
dbus-glib
0.100
http://dbus.freedesktop.org/releases/dbusglib/dbus-glib-0.100.tar.gz
dnsmasq
2.47
http://www.thekelleys.org.uk/dnsmasq/dnsmasq2.47.tar.gz
dosfstools
3.0.9
http://www.danielbaumann.ch/software/dosfstools/dosfstools3.0.9.tar.bz2
dropbear
2015.67
http://matt.ucc.asn.au/dropbear/releases/dropbear
-2015.67.tar.bz2
e2fsprogs
1.42.4
http://downloads.sourceforge.net/sourceforge/e2f
sprogs/e2fsprogs-1.42.4.tar.gz
ebtables
2.0.10+1
http://downloads.sourceforge.net/sourceforge/ebt
ables/ebtables/ebtables-2-0-10-1/ebtablesv2.0.10-1.tar.gz
ethtool
3.0
http://www.kernel.org/pub/linux/../software/netw
ork/ethtool/ethtool-3.0.tar.bz2
eventlog
0.2.12
http://www.balabit.com/downloads/files/syslogng/sources/2.0/src/eventlog-0.2.12.tar.gz
expat
2.1.0
http://downloads.sourceforge.net/sourceforge/exp
at/expat-2.1.0.tar.gz
figlet
2.2.5
ftp://ftp.figlet.org/pub/figlet/program/unix/figlet2.2.5.tar.gz
fuse
2.9.0
http://downloads.sourceforge.net/sourceforge/fus
e/fuse-2.9.0.tar.gz
gdbserver
7.2a
http://ftp.uni-kl.de/pub/gnu/gdb/gdb-7.2a.tar.bz2
gcclibs
4.7.3
glib
2.34.3
License
GPLv2
GPLv2
GPLv2
GPLv2
GPLv3
GPLv2
GPLv2
GPLv2/Academic
Free Licence v2.1
GPLv2/Academic
Free Licence v2.1
GPLv2/GPLv3
GPLv3
Multiple
GPLv2
GPLv2
GPLv2
Balabit
Expat
Figlet
GPLv2/LGPLv2.1
GPLv2/GPLv3/LG
PLv2/LGPLv3
ftp://ftp.fuGPLv3 mit GCC
berlin.de/unix/languages/gcc/releases/gccRuntime Library
4.7.3/gcc-4.7.3.tar.bz2
Exception
http://ftp.gnome.org/pub/GNOME/sources/glib/2. LGPLv2
34/glib-2.34.3.tar.xz
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
390
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 299: Overview of Open Source Licenses
Software
Version
Url
Package
glibc
2.16
http://ftp.gnu.org/gnu/glibc/glibc-2.16.0.tar.bz2
gzip
1.6
http://ftp.gnu.org/gnu/gzip/gzip-1.6.tar.gz
hexedit
1.2.12
http://rigaux.org/hexedit-1.2.12.src.tgz
htop
1.0.3
http://downloads.sourceforge.net/sourceforge/hto
p/htop-1.0.3.tar.gz
ifplugd
0.28
http://0pointer.de/lennart/projects/ifplugd/ifplugd
-0.28.tar.gz
inetutils
1.6
http://ftp.uni-kl.de/pub/gnu/inetutils/inetutils1.6.tar.gz
iperf
2.0.4
http://downloads.sourceforge.net/sourceforge/ipe
rf/iperf-2.0.4.tar.gz
ipkg
0.99.163
http://www.pengutronix.de/software/ptxdist/temp
orary-src/ipkg-0.99.163.tar.gz
iproute2
3.14.0
https://www.kernel.org/pub/linux/utils/net/iprout
e2/iproute2-3.14.0.tar.gz
iptables
1.4.16.3
http://ftp.netfilter.org/pub/iptables/iptables1.4.16.3.tar.bz2
ipwatchd
1.2.1
http://svsv01003.wago.local/wago-ptxdistsrc/ipwatchd-1.2.1.tar.gz
kbd
1.15.2
http://www.kernel.org/pub/linux/utils/kbd/kbd1.15.2.tar.bz2
less
443
http://ftp.uni-kl.de/pub/gnu/less/less-443.tar.gz
libcgroup
0.41
http://downloads.sourceforge.net/sourceforge/libc
g/libcgroup-0.41.tar.bz2
libconfig
1.4.9
http://www.hyperrealm.com/libconfig/libconfig1.4.9.tar.gz
libcurl
7.26.0
http://curl.haxx.se/download/curl-7.26.0.tar.gz
libdaemon 0.14
http://0pointer.de/lennart/projects/libdaemon/libd
aemon-0.14.tar.gz
libelf
0.8.13
http://www.mr511.de/software/libelf0.8.13.tar.gz
libffi
3.0.11
http://ftp.gwdg.de/pub/linux/sources.redhat.com/l
ibffi/libffi-3.0.11.tar.gz
libgmp
4.2.4
http://ftp.uni-kl.de/pub/gnu/gmp/gmp4.2.4.tar.bz2
libkmod
10
http://www.kernel.org/pub/linux/utils/kernel/kmo
d/kmod-10.tar.xz
liblzo
2.03
http://www.oberhumer.com/opensource/lzo/down
load/lzo-2.03.tar.gz
libmodbus 3.0.5
http://svsv01003.wago.local/wago-ptxdistsrc/libmodbus-3.0.5.tar.gz
libmodbus- 0.9.20
http://svsv01003.wago.local/wago-ptxdistglx
src/libModbus-0.9.20.tar.gz
libnet
1.1.4
http://downloads.sourceforge.net/sourceforge/lib
net-dev/libnet-1.1.4.tar.gz
libnl3
3.2.22
http://www.infradead.org/~tgr/libnl/files/libnl3.2.22.tar.gz
libpcap
1.5.3
http://www.tcpdump.org/release/libpcap1.5.3.tar.gz
libpcre
8.32
http://downloads.sourceforge.net/sourceforge/pcr
e/pcre-8.32.tar.bz2
License
LGPLv2.1
GPLv3
GPLv2
GPLv2
GPLv2
GPLv3
Iperf
GPLv2
GPLv2
GPLv2
GPLv2
GPLv2
less
LGPLv2.1
LGPLv2.1
curl
LGPLv2.1
LGPLv2
libffi
GPLv3/LGPLv3
GPLv2
GPLv2
GPLv3/LGPLv2.1
LGPLv2
libnet
LGPLv2.1
BSD (3-clause)
PCRE
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 299: Overview of Open Source Licenses
Software
Version
Url
Package
libpng
1.2.50
http://downloads.sourceforge.net/sourceforge/lib
png/libpng-1.2.50.tar.xz
libpopt
1.15
http://rpm5.org/files/popt/popt-1.15.tar.gz
libsocketcan 0.0.9
http://www.pengutronix.de/software/libsocketcan
/download/libsocketcan-0.0.9.tar.bz2
libsysfs
2.1.0
http://downloads.sourceforge.net/sourceforge/lin
ux-diag/sysfsutils-2.1.0.tar.gz
libuci
gitmaster
http://svsv01003.wago.local/wago-ptxdistsrc/libuci-gitmaster.tar.gz
libusb
1.0.8
http://downloads.sourceforge.net/sourceforge/lib
usb/libusb-1.0.8.tar.bz2
libusb0.1.3
http://downloads.sourceforge.net/sourceforge/lib
compat
usb/libusb-compat-0.1.3.tar.bz2
libxml2
2.7.7
ftp://xmlsoft.org/libxml2/libxml2-2.7.7.tar.gz
libxslt
1.1.26
ftp://xmlsoft.org/libxslt/libxslt-1.1.26.tar.gz
lighttpd
1.4.35
http://download.lighttpd.net/lighttpd/releases1.4.x/lighttpd-1.4.35.tar.bz2
lmbench
3.0+a9
http://downloads.sourceforge.net/sourceforge/lm
bench/lmbench-3.0-a9.tgz
logrotate
3.7.1
http://www.pengutronix.de/software/ptxdist/temp
orary-src/logrotate-3.7.1.tar.gz
lsof
4.81.dfsg.1 http://ftp.unikl.de/debian/pool/main/l/lsof/lsof_4.81.dfsg.1.ori
g.tar.gz
lsuio
0.2.0
http://www.osadl.org/projects/downloads/UIO/us
er/lsuio-0.2.0.tar.gz
ltrace
0.5.1
http://www.pengutronix.de/software/ptxdist/temp
orary-src/ltrace_0.5.1.orig.tar.gz
memedit
0.9
http://www.pengutronix.de/software/memedit/do
wnloads/memedit-0.9.tar.gz
mii-diag
2.11
http://ftp.uni-kl.de/debian/pool/main/m/miidiag/mii-diag_2.11.orig.tar.gz
mtd-utils
1.5.0
ftp://ftp.infradead.org/pub/mtd-utils/mtd-utils1.5.0.tar.bz2
nano
2.3.1
http://www.nano-editor.org/dist/v2.3/nano2.3.1.tar.gz
ncurses
5.9
http://ftp.uni-kl.de/pub/gnu/ncurses/ncurses5.9.tar.gz
net-snmp
5.7.2
http://downloads.sourceforge.net/sourceforge/net
-snmp/net-snmp-5.7.2.tar.gz
netkit-ftp
0.17
ftp://ftp.uk.linux.org/pub/linux/Networking/netkit
/netkit-ftp-0.17.tar.gz
nfsutils
1.2.3
http://downloads.sourceforge.net/sourceforge/nfs/
nfs-utils-1.2.3.tar.bz2
ntfs-3g
2014.2.15
http://svsv01003.wago.local/wago-ptxdistsrc/ntfs-3g_ntfsprogs-2014.2.15.tgz
ntpclient
365
http://doolittle.icarus.com/ntpclient/ntpclient_200
7_365.tar.gz
openssh
5.8p2
http://openbsd.cs.fau.de/pub/OpenBSD/OpenSSH
/portable/openssh-5.8p2.tar.gz
openssl
1.0.1j
http://openssl.org/source/openssl-1.0.1j.tar.gz
openvpn
2.3.4
http://openvpn.net/release/openvpn-2.3.4.tar.gz
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Appendix
391
License
LIBPNG
popt
LGPLv2.1
LGPLv2
GPLv2/LGPLv2.1
LGPLv2.1
LGPLv2.1
libxml2
libxslt
lighttpd
GPLv2 +
Extension
GPLv2
lsof
GPLv2
GPLv2
GPLv2
GPL
GPLv2
GPLv3
ncurses
Multiple
BSD (4-clause)
GPLv2
GPLv2/LGPLv2
GPLv2
OpenSSH License
OpenSSL License
Multiple
392
Appendix
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 299: Overview of Open Source Licenses
Software
Version
Url
Package
php5
5.3.27
http://museum.php.net/php5/php-5.3.27.tar.bz2
portmap
6.0
http://neil.brown.name/portmap/portmap-6.0.tgz
ppp
2.4.5
http://ftp.samba.org/pub/ppp/ppp-2.4.5.tar.gz
procps
3.2.8
http://procps.sourceforge.net/procps-3.2.8.tar.gz
pureftpd
1.0.36
http://download.pureftpd.org/pub/pureftpd/releases/pure-ftpd-1.0.36.tar.bz2
pv
1.3.4
http://pipeviewer.googlecode.com/files/pv1.3.4.tar.gz
readline
6.2
http://ftp.uni-kl.de/pub/gnu/readline/readline6.2.tar.gz
rt-tests
0.73
http://www.kernel.org/pub/linux/kernel/people/cl
rkwllms/rt-tests/rt-tests-0.73.tar.bz2
screen
4.0.3
http://ftp.uni-kl.de/pub/gnu/screen/screen4.0.3.tar.gz
sed
4.2.1
http://ftp.uni-kl.de/pub/gnu/sed/sed-4.2.1.tar.bz2
setserial
2.17
http://downloads.sourceforge.net/sourceforge/sets
erial/setserial-2.17.tar.gz
spawn-fcgi 1.6.3
http://download.lighttpd.net/spawn-fcgi/releases1.6.x/spawn-fcgi-1.6.3.tar.bz2
strace
4.10
http://downloads.sourceforge.net/sourceforge/stra
ce/strace-4.10.tar.xz
strongswan 5.1.3
http://download.strongswan.org/strongswan5.1.3.tar.gz
sudo
1.7.2p6
http://www.sudo.ws/sudo/dist/sudo-1.7.2p6.tar.gz
swconfig
git-snapshot https://github.com/openwrt2013-11-05 mirror/openwrt/tree/master/package/network/con
fig/swconfig
syslogng
3.3.4
http://www.balabit.com/downloads/files/syslogng/sources/3.3/src/syslog-ng-3.3.4.tar.gz
tar
1.26
http://ftp.uni-kl.de/pub/gnu/tar/tar-1.26.tar.xz
tcpdump
4.5.1
http://www.tcpdump.org/release/tcpdump4.5.1.tar.gz
timezone
1.0
https://www.iana.org/time-zones/repository/tzlink.html
udev
172
http://www.kernel.org/pub/linux/utils/kernel/hotp
lug/udev-172.tar.bz2
umkimage 2010.03+1 http://www.pengutronix.de/software/ptxdist/temp
orary-src/u-boot-mkimage-2010.03-1.tar.gz
unzip
5.52
http://downloads.sourceforge.net/sourceforge/inf
ozip/unzip552.tar.gz
usbutils
004
http://www.kernel.org/pub/linux/utils/usb/usbutil
s/usbutils-004.tar.bz2
util-linux-ng 2.21.2
http://www.kernel.org/pub/linux/utils/utillinux/v2.21/util-linux-2.21.2.tar.bz2
xmlstarlet
1.3.1
http://downloads.sourceforge.net/sourceforge/xm
lstar/xmlstarlet-1.3.1.tar.gz
zip
3.0
http://surfnet.dl.sourceforge.net/sourceforge/infoz
ip/zip30.tar.gz
zlib
1.2.8
http://zlib.net/zlib-1.2.8.tar.xz
License
PHP License
BSD
BSD/GPLv2
GPLv2/LGPLv2
BSD/Custom
Artistic License 2.0
GPLv3
GPLv2
GPLv2
GPLv3
GPL
Custom
Custom
GPLv2
ISC-style
GPLv2/LGPLv2.1
GPL/LGPL
GPLv3
BSD (3-clause)
Public Domain
GPLv2
GPLv2
Custom
GPLv2
GPLv2
Custom
Custom
Custom
=== Ende der Liste für T extmar ke Inhalt_mitte ===
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
List of Figures
393
Pos : 92 /D okumentation allgemei n/Verz eic hniss e/Abbil dungs verz eic hnis - Übersc hrift oG und Verz eichnis @ 3\mod_1219222916765_21.doc x @ 21080 @ @ 1
List of Figures
Figure 1: View ....................................................................................................... 27
Figure 2: Marking Area for Serial Numbers ......................................................... 29
Figure 3: Data Contacts ......................................................................................... 30
Figure 4: Power Jumper Contacts ......................................................................... 31
Figure 5: CAGE CLAMP® Connectors................................................................. 32
Figure 6: Service Interface (Closed and Open Flap) ............................................. 33
Figure 7: Network Connections – X1, X2 ............................................................. 34
Figure 8: RS-232/RS-485 – X3 Communication Connection ............................... 35
Figure 9: Termination with DTE-DCE Connection (1:1) ..................................... 36
Figure 10: Termination with DTE-DTE Connection (Cross-Over) ...................... 36
Figure 11: RS-485 Bus Termination ..................................................................... 37
Figure 12: Power Supply Indicating Elements ...................................................... 38
Figure 13: Indicating Elements for Fieldbus/System ............................................ 39
Figure 14: Indicating Elements, Memory Card Slot ............................................. 40
Figure 15: Indicating Elements, RJ-45 Jacks ........................................................ 41
Figure 16: Mode Selector Switch .......................................................................... 42
Figure 17: Reset Button ......................................................................................... 43
Figure 18: Slot for SD Memory Card .................................................................... 44
Figure 19: Schematic Diagram .............................................................................. 45
Figure 20: Spacing................................................................................................. 72
Figure 21: Release Tab of Controller (Example) .................................................. 74
Figure 22: Insert I/O Module (Example) ............................................................... 75
Figure 23: Snap the I/O Module into Place (Example) ......................................... 75
Figure 24: Example for the Arrangement of Power Contacts ............................... 77
Figure 25: Connecting a Conductor to a CAGE CLAMP® ................................... 78
Figure 26: Power Supply Concept......................................................................... 79
Figure 27: Power Supply Example........................................................................ 81
Figure 28: Carrier Rail Contact (Example) ........................................................... 85
Figure 29: Cable Shield at Ground Potential......................................................... 86
Figure 30: Examples of the WAGO Shield Connecting System........................... 87
Figure 31: Application of the WAGO Shield Connecting System ....................... 87
Figure 32: “Open DHCP”, Example Figure .......................................................... 91
Figure 33: CBM Starting Screen ........................................................................... 92
Figure 34: CBM – Selecting “Networking” .......................................................... 93
Figure 35: CBM – Selecting “TCP/IP” ................................................................. 93
Figure 36: CBM – Selecting “IP address”............................................................. 93
Figure 37: CBM – Selecting the IP Address ......................................................... 94
Figure 38: CBM – Entering a New IP Address ..................................................... 94
Figure 39: “WAGO Ethernet Settings” – Starting Screen (Example)................... 95
Figure 40: “WAGO Ethernet Settings” – “Network” Tab .................................... 96
Figure 41: Example of a Function Test ................................................................. 98
Figure 42: Entering Authentication ..................................................................... 105
Figure 43: Password Reminder ........................................................................... 106
Figure 44: WBM Browser Window (Example) .................................................. 109
Figure 45: WBM Status Information (Example) ................................................. 109
Figure 46: CBM main menu (example) .............................................................. 160
Figure 47: “WAGO ETHERNET Settings” – Start Screen ................................ 210
Figure 48: “WAGO ETHERNET Settings” – Communication Link.................. 211
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
394
List of Figures
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Figure 49: “WAGO ETHERNET Settings” – Identification Tab (Example) ..... 212
Figure 50: “WAGO ETHERNET Settings” – Network Tab ............................... 213
Figure 51: “WAGO ETHERNET Settings” – Protocol Tab ............................... 215
Figure 52: “WAGO ETHERNET Settings” – Status Tab ................................... 216
Figure 53: Target System Settings (1) ................................................................. 218
Figure 54: Target System Settings (2) ................................................................. 218
Figure 55: Creating a New Function Block......................................................... 219
Figure 56: Programming Interface With the PLC_PRG Program Module ......... 219
Figure 57: “Resources” Tab ................................................................................ 220
Figure 58: Control Configuration – Edit ............................................................. 221
Figure 59: “Start WAGO-I/O-CHECK and Scan” Button .................................. 221
Figure 60: WAGO-I/O-CHECK – Starting Screen ............................................. 222
Figure 61: I/O Configurator Empty ..................................................................... 223
Figure 62: “Add I/O Modules” Button ................................................................ 223
Figure 63: “Module Selection” Window ............................................................. 224
Figure 64: I/O Configurator with Defined I/O Modules ..................................... 224
Figure 65: Variable Declaration .......................................................................... 225
Figure 66: Control Configuration: I/O Modules with Their Associated
Addresses ................................................................................................... 225
Figure 67: Program Function Block .................................................................... 226
Figure 68: Input Assistant for Selecting Variables ............................................. 226
Figure 69: Example of an Allocation .................................................................. 227
Figure 70: Creating a Communication Link – Step 1 ......................................... 228
Figure 71: Creating a Communication Link – Step 2 ......................................... 229
Figure 72: Creating a Communication Link – Step 3 ......................................... 229
Figure 73: Task Configuration ............................................................................ 231
Figure 74: Changing Task Names 1 .................................................................... 232
Figure 75: Call-up to Add to the Program Module ............................................. 233
Figure 76: Cyclic Task ........................................................................................ 234
Figure 77: Freewheeling Task ............................................................................. 235
Figure 78: CODESYS – System Events.............................................................. 236
Figure 79: CODESYS Program Provokes Division by “0” ................................ 238
Figure 80: CODESYS – Creating and Activating an Event Handler .................. 238
Figure 81: CODESYS – New Module has been Generated ................................ 239
Figure 82: CODESYS – Enter the Event in a Global Variable ........................... 239
Figure 83: CODESYS – Variable Contents Prior to Division by “0” ................. 240
Figure 84: CODESYS – Variable Contents After Division by “0” and
Call-up of the Event Handler ..................................................................... 240
Figure 85: Process Image .................................................................................... 241
Figure 86: Flag Area............................................................................................ 242
Figure 87: Internal Data Bus Synchronization 01 ............................................... 246
Figure 88: I/O Module Synchronization 02 ........................................................ 247
Figure 89: I/O Module Synchronization 03 ........................................................ 248
Figure 90: Internal Data Bus Synchronization 04 ............................................... 249
Figure 91: Internal Data Bus Settings ................................................................. 250
Figure 92: Program Memory ............................................................................... 253
Figure 93: Data Memory and Function Block Limitation ................................... 254
Figure 94: Remanent Main Memory ................................................................... 254
Figure 95: Flag and Retain Memory ................................................................... 255
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
List of Figures
395
Figure 96: Selecting the Visualization Technique in the Target System
Settings ....................................................................................................... 256
Figure 97: Creating the PLC_VISU Starting Visualization ................................ 257
Figure 98: Remanent Main Memory ................................................................... 265
Figure 99: CODESYS PLC Configuration - MODBUS Settings ....................... 267
Figure 100: MODBUS Process Image ................................................................ 273
Figure 101: Flag Area.......................................................................................... 274
Figure 102: MODBUS Address Overview ......................................................... 292
Figure 103: Power Supply Indicating Elements .................................................. 303
Figure 104: Indicating Elements for Fieldbus/System ........................................ 304
Figure 105: Flashing Sequence Process Diagram ............................................... 309
Figure 106: Inserting the Memory Card .............................................................. 316
Figure 107: Release Tab of Controller (Example) .............................................. 320
Figure 108: Removing the I/O Module (Example) ............................................. 321
Figure 109: Side Marking Example for Approved I/O Modules According to
ATEX and IECEx ...................................................................................... 323
Figure 110: Text Detail – Marking Example for Approved I/O Modules
According to ATEX and IECEx. ............................................................... 323
Figure 111: Side Marking Example for Approved Ex i I/O Modules
According to ATEX and IECEx. ............................................................... 325
Figure 112: Text Detail – Marking Example for Approved Ex i I/O Modules
According to ATEX and IECEx. ............................................................... 325
Figure 113: Side Marking Example for I/O Modules According to NEC 500 ... 328
Figure 114: Text Detail – Marking Example for Approved I/O Modules
According to NEC 500............................................................................... 328
Figure 115: Graphical Representation of the “ConfigToolFB” Function
Block .......................................................................................................... 370
Pos : 93 /D okumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
396
List of Tables
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Pos : 94 /D okumentation allgemei n/Verz eic hniss e/Tabell enverz eichnis - Übersc hrift oG und Verz eichnis @ 3\mod_1219222958703_21.doc x @ 21084 @ @ 1
List of Tables
Table 1: Number Notation ..................................................................................... 18
Table 2: Font Conventions .................................................................................... 18
Table 3: Legend for Figure “View” ...................................................................... 27
Table 4: Legend for Figure “Power Jumper Contacts” ......................................... 31
Table 5: Legend for Figure “CAGE CLAMP® Connectors” ................................ 32
Table 6: Service Interface...................................................................................... 33
Table 7: Legend for Figure “Network Connections – X1, X2” ............................ 34
Table 8: Legend for Figure “RS-232/RS-485 – X3 Communication
Connection” ................................................................................................. 35
Table 9: Function of RS-232 Signals for DTE/DCE ............................................. 36
Table 10: Legend for Figure “Power Supply Indicating Elements” ..................... 38
Table 11: Legend for Figure “Fieldbus/System Indicating Elements” ................. 39
Table 12: Legend for Figure “Indicating Elements, Memory Card Slot” ............. 40
Table 13: Legend for Figure “Indicating Elements, RJ-45 Jacks” ........................ 41
Table 14: Mode Selector Switch ........................................................................... 42
Table 15: Mode Selector Switch ........................................................................... 42
Table 16: Technical Data – Device ....................................................................... 46
Table 17: Technical Data – System Data .............................................................. 46
Table 18: Technical Data – Supply ....................................................................... 46
Table 19: Technical Data – Clock ......................................................................... 47
Table 20: Technical Data – Programming ............................................................ 47
Table 21: Technical Data – Internal Data Bus ...................................................... 47
Table 22: Technical Data – ETHERNET .............................................................. 48
Table 23: Technical Data – Serial Interface .......................................................... 48
Table 24: Technical Data – Field Wiring .............................................................. 48
Table 25: Technical Data – Power Jumper Contacts ............................................ 48
Table 26: Technical Data – Data Contacts ............................................................ 48
Table 27: Technical Data – Mechanical Conditions ............................................. 49
Table 28: Technical Data – Climatic Environmental Conditions ......................... 49
Table 29: Climatic and Mechanical Environmental Conditions ........................... 52
Table 30: EMC – Immunity to Interference .......................................................... 53
Table 31: EMC – Emission of Interference........................................................... 54
Table 32: WBM Users ........................................................................................... 58
Table 33: Linux® Users ......................................................................................... 58
Table 34: List of Parameters Transmitted via DHCP............................................ 62
Table 35: WAGO DIN Rail................................................................................... 71
Table 36: Permissible WAGO Carrier Rails When Using XTR PFC200 ............. 71
Table 37: Filter Modules for 24 V Power Supply ................................................. 79
Table 38: Legend for Figure “Power Supply Example” ....................................... 82
Table 39: WAGO Power Supply Units ................................................................. 83
Table 40: WAGO Ground Wire Terminals ........................................................... 84
Table 41: Default IP Addresses for ETHERNET Interfaces ................................. 90
Table 42: Network Mask 255.255.255.0 ............................................................... 90
Table 43: User Settings in the Default State ....................................................... 106
Table 44: Access Rights for WBM Pages ........................................................... 107
Table 45: WBM “Status Information” Page – “Controller Details” Group ........ 112
Table 46: WBM “Status Information Page – “Network Details (Xn)”
Group(s) ..................................................................................................... 112
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
List of Tables
397
Table 47: WBM “General PLC Runtime Configuration” Page –
“General PLC Runtime Configuration” Group.......................................... 113
Table 48: WBM “PLC Runtime Information” Page – “PLC Runtime” Group .. 115
Table 49: WBM “PLC Runtime Information” Page – “Project Details” Group . 115
Table 50: WBM “PLC Runtime Information” Page – “Task n” Group(s) ......... 116
Table 51: WBM “PLC WebVisu” Page – “Web Server Configuration” Group . 117
Table 52: WBM “Configuration of Host and Domain Name” Page –
“Hostname” Group..................................................................................... 118
Table 53: WBM “Configuration of Host and Domain Name” Page –
“Domain Name” Group ............................................................................. 118
Table 54: WBM “TCP/IP Configuration” Page – “IP Configuration (Xn)”
Group(s) ..................................................................................................... 119
Table 55: WBM “TCP/IP Configuration” Page – “Default Gateway n” Group . 120
Table 56: WBM “TCP/IP Configuration” Page – “DNS Server” Group ............ 120
Table 57: WBM “Ethernet Configuration” Page – “Switch Configuration”
Group ......................................................................................................... 121
Table 58: WBM “Ethernet Configuration” Page – “Interface Xn” Groups ........ 122
Table 59: WBM “General Firewall Configuration” Page – “Global Firewall
Parameters” Group ..................................................................................... 123
Table 60: WBM “General Firewall Configuration” Page – “Firewall
Parameter Interface Xn” Group ................................................................. 124
Table 61: WBM “General Firewall Configuration” Page – “Firewall
Parameter Interface VPN” Group .............................................................. 125
Table 62: WBM “Configuration of MAC Address Filter” Page – “Global
MAC Address Filter State” Group ............................................................. 126
Table 63: WBM “Configuration of MAC Address Filter” Page – “MAC
Address Filter State Xn” Group ................................................................. 127
Table 64: WBM “Configuration of MAC Address Filter” Page – “MAC
Address Filter Whitelist” Group ................................................................ 127
Table 65: WBM “Configuration of User Filter” Page – “User Filter” Group ... 128
Table 66: WBM “Configuration of User Filter” Page – “User Filter n” Group . 128
Table 67: WBM “Configuration of User Filter” Page – “Add New User
Filter” Group .............................................................................................. 129
Table 68: WBM “Configuration of Time and Date” Page – “Date on Device”
Group ......................................................................................................... 130
Table 69: WBM “Configuration of Time and Date” Page – “Time on Device”
Group ......................................................................................................... 130
Table 70: WBM “Configuration of Time and Date” Page – “Timezone”
Group ......................................................................................................... 131
Table 71: WBM “Configuration of Time and Date” Page – “TZ String”
Group ......................................................................................................... 131
Table 72: WBM “Configuration of the users for the Web-based Management”
Page – “Change Password for Selected User” Group ................................ 132
Table 73: WBM “Create Bootable Image” page – “Create bootable image
from active partition” Group...................................................................... 133
Table 74: WBM “Configuration of Serial Interface RS232” Page – “Assign
Owner of Serial Interface” Group .............................................................. 135
Table 75: WBM “Configuration of Serial Interface RS-232” page – “Assign
Owner of Service Interface” Group ........................................................... 136
Table 76: WBM “Mass Storage” Page – “<Device Name>” Group ................... 141
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
398
List of Tables
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 77: WBM “Mass Storage” Page – “<Device Name>” Group ................... 141
Table 78: WBM “Software Uploads” Page – “Upload New Software” Group .. 142
Table 79: WBM “Software Uploads” Page – “Activate New Software” Group 142
Table 80: WBM “Configuration of Network Services” Page – “Telnet” Group 143
Table 81: WBM “Configuration of Network Services” Page – “FTP” Group ... 143
Table 82: WBM “Configuration of Network Services” Page – “FTPS” Group . 143
Table 83: WBM “Configuration of Network Services” Page – “HTTP” Group 143
Table 84: WBM “Configuration of Network Services” Page – “HTTPS”
Group ......................................................................................................... 144
Table 85: WBM “Configuration of Network Services” Page – “I/O-CHECK”
Group ......................................................................................................... 144
Table 86: WBM “Configuration of NTP Client” Page – “NTP Client
Configuration” Group ................................................................................ 145
Table 87: WBM “Configuration of PLC Runtime Services” Page – “General
Configuration” Group ................................................................................ 146
Table 88: WBM “Configuration of CODESYS Services” Page –
“CODESYS 2 Web Server” Group............................................................ 146
Table 89: WBM “Configuration of CODESYS Services” Page –
“e!RUNTIME Web Server” Group ............................................................ 146
Table 90: WBM “SSH Server Settings” Page – “SSH Server” Group ............... 147
Table 91: WBM “TFTP Server” Page – “TFTP Server” Group ......................... 148
Table 92: WBM “DHCP Configuration” – “DHCP Configuration Xn” Group . 149
Table 93: WBM “Configuration of DNS Service” Page – “DNS Service”
Group ......................................................................................................... 150
Table 94: WBM “MODBUS Services Configuration” Page –
“MODBUS TCP” Group ........................................................................... 151
Table 95: WBM “MODBUS Configuration Services” Page –
“MODBUS UDP” Group ........................................................................... 151
Table 96: WBM “Configuration of General SNMP Parameters” Page –
“General SNMP Configuration” Group ..................................................... 152
Table 97: WBM “Configuration of SNMP v1/v2c Parameters” Page –
“SNMP v1/v2c Manager Configuration” Group ....................................... 153
Table 98: WBM “Configuration of SNMP v1/v2c Parameters” Page –
“Actually Configured Trap Receivers” Group .......................................... 153
Table 99: WBM “Configuration of SNMP v1/v2c Parameters” Page – “Trap
Receiver n” Group(s) ................................................................................. 154
Table 100: WBM “Configuration of SNMP v1/v2c Parameters” Page –
“Add New Trap Receiver” Group.............................................................. 154
Table 101: WBM “Configuration of SNMP v3” Page – “Actually
Configured v3 Users” Group ..................................................................... 155
Table 102: WBM “Configuration of SNMP v3 Users” Page – “v3 User n”
Group(s) ..................................................................................................... 155
Table 103: WBM “Configuration of SNMP v3 Users” Page – “Add New v3
User” Group ............................................................................................... 156
Table 104: WBM “Diagnostic Information” Page .............................................. 157
Table 105: WBM “Configuration of OpenVPN and IPsec” Page –
“OpenVPN” Group .................................................................................... 158
Table 106: WBM “Configuration of OpenVPN and IPsec” Page – “IPsec”
Group ......................................................................................................... 158
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
List of Tables
399
Table 107: WBM “Configuration of OpenVPN and IPsec” Page –
“Certificate Upload” Group ....................................................................... 159
Table 108: WBM “Configuration of OpenVPN and IPsec” Page –
“Certificate List” Group ............................................................................. 159
Table 109: WBM “Configuration of OpenVPN and IPsec” Page –
“Private Key List” Group........................................................................... 159
Table 110: CBM Menu Structure ........................................................................ 160
Table 111: “Information” Menu .......................................................................... 163
Table 112: “Information” > “Controller Details” Submenu ............................... 163
Table 113: “Information” > “Network Details” Submenu .................................. 164
Table 114: “PLC Runtime” Menu ....................................................................... 165
Table 115: “PLC Runtime” > “Information” Submenu ...................................... 165
Table 116: “PLC Runtime” > “Information” > “Runtime Version” Submenu ... 166
Table 117: “PLC Runtime” > “Information” > “Webserver Version” Submenu 166
Table 118: “PLC Runtime” > “Information” > “State” Submenu ...................... 166
Table 119: “PLC Runtime” > “Information” > “Number of Tasks” Submenu... 167
Table 120: “PLC Runtime” > “Information” > “Project Details” Submenu ....... 167
Table 121: “PLC Runtime” > “Information” > “Tasks” Submenu ..................... 167
Table 122: “PLC Runtime” > “Information” > “Tasks” > “Task n” Submenu .. 168
Table 123: “PLC Runtime” > “General Configuration” Submenu ..................... 168
Table 124: “PLC Runtime” > “General Configuration” > “PLC Runtime
Version” Submenu ..................................................................................... 169
Table 125: “PLC Runtime” > “General Configuration” > “Home Dir On SD
Card” Submenu .......................................................................................... 169
Table 126: “PLC Runtime” > “WebVisu” Submenu .......................................... 170
Table 127: “Networking” Menu .......................................................................... 171
Table 128: “Networking” > “Host/Domain Name” Submenu ............................ 171
Table 129: “Networking” > “Hostname” Submenu ............................................ 172
Table 130: “Networking” > “Host/Domain Name” > “Domain Name”
Submenu .................................................................................................... 172
Table 131: “Networking” > “TCP/IP” Submenu ................................................ 172
Table 132: “Networking” > “IP Address” Submenu........................................... 173
Table 133: “Networking” > “TCP/IP” > “IP Address” Submenu > “Xn” .......... 173
Table 134: “Networking” > “TCP/IP” > “Default Gateway” Submenu ............. 174
Table 135: “Networking” > “TCP/IP” > “Default Gateway” > “Default
Gateway n” Submenu ................................................................................ 174
Table 136: “Networking” > “TCP/IP” > “DNS Server” Submenu ..................... 175
Table 137: “Networking” > “Ethernet” Submenu ............................................... 175
Table 138: “Networking” > “Ethernet” > “Switch Configuration” Submenu .... 176
Table 139: “Networking” > “Ethernet” > “Ethernet Ports” Submenu ................ 176
Table 140: “Networking” > “Ethernet” > “Ethernet Ports” > “Interface Xn”
Submenu .................................................................................................... 177
Table 141: “Firewall” Menu................................................................................ 178
Table 142: “Firewall” > “General Configuration” Submenu .............................. 179
Table 143: “Firewall” > “General Configuration” > “Interface xxx” Submenu . 180
Table 144: “Firewall” > “MAC Address Filter” Submenu ................................. 181
Table 145: “Firewall” > “MAC Address Filter” > “MAC address filter
whitelist” Submenu .................................................................................... 182
Table 146: “Firewall” > “MAC Address Filter” > “MAC address filter
whitelist” > “Add new / No (n)” Submenu ................................................ 182
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
400
List of Tables
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 147: “Firewall” > “User Filter” Submenu ................................................. 183
Table 148: “Firewall” > “User Filter” > “Add New / No (n)” Submenu ............ 184
Table 149: “Clock” Menu ................................................................................... 185
Table 150: “Administration” Menu ..................................................................... 186
Table 151: “Administration” > “Create Image” Submenu .................................. 187
Table 152: “Administration” > “Users” Submenu .............................................. 187
Table 153: “Package Server” Menu .................................................................... 188
Table 154: “Package Server” > “Firmware Backup” Menu................................ 188
Table 155: “Package Server” > “Firmware Backup” > “Auto Update
Feature” Menu ........................................................................................... 189
Table 156: “Package Server” > “Firmware Backup” > “Auto Update
Feature” Menu ........................................................................................... 189
Table 157: “Package Server” > “Firmware Restore” Menu................................ 190
Table 158: “Package Server” > “Firmware Restore” > “Select Package”
Menu .......................................................................................................... 190
Table 159: “Package Server” > “System Partition” Submenu ............................ 191
Table 160: “Mass Storage” Menu ....................................................................... 192
Table 161: “Mass Storage” > “SD Card” Menu.................................................. 192
Table 162: “Ports and Services” Menu ............................................................... 194
Table 163: “Ports and Services” > “Telnet” Submenu........................................ 195
Table 164: “Ports and Services” > “FTP” Submenu ........................................... 195
Table 165: “Ports and Services” > “FTPS” Submenu......................................... 196
Table 166: “Ports and Services” > “HTTP” Submenu ........................................ 196
Table 167: “Ports and Services” > “HTTPS” Submenu...................................... 197
Table 168: “Ports and Services” > “NTP” Submenu .......................................... 197
Table 169: “Ports and Services” > “SSH” Submenu .......................................... 198
Table 170: “Ports and Services” > “TFTP” Submenu ........................................ 198
Table 171: “Ports and Services” > “DHCPD” Submenu .................................... 199
Table 172: “Ports and Services” > “DHCPD” > “Xn” Submenu........................ 199
Table 173: “Ports and Services” > “DNS” Submenu .......................................... 200
Table 174: “Ports and Services” > “IOCHECK PORT” Submenu ..................... 201
Table 175: “Ports and Services” > “Modbus TCP” Submenu ............................ 201
Table 176: “Ports and Services” > “Modbus UDP” Submenu ............................ 202
Table 177: “Ports and Services” > “PLC Runtime Services” Submenu ............. 202
Table 178: “Ports and Services” > “PLC Runtime Services” >
“CODESYS 2” Submenu ........................................................................... 203
Table 179: “Ports and Services” > “PLC Runtime Services” >
“e!RUNTIME” Submenu........................................................................... 204
Table 180: “Ports and Services” > “Firewall Status” Submenu .......................... 205
Table 181: “SNMP” Menu .................................................................................. 206
Table 182: “SNMP” > “General SNMP Configuration” Submenu .................... 206
Table 183: “SNMP” > “SNMP v1/v2c Manager Configuration” Submenu ....... 207
Table 184: “SNMP” > “SNMP v1/v2c Trap Receiver Configuration”
Submenu .................................................................................................... 207
Table 185: “SNMP” > “SNMP v3 Configuration” Submenu ............................. 208
Table 186: “SNMP” > “(Secure )SNMP firewalling” Submenu ........................ 209
Table 187: Syntax of Logical Addresses ............................................................. 230
Table 188: Events ................................................................................................ 237
Table 189: Access to the Process Images of the Input and Output Data –
Internal Data Bus ....................................................................................... 243
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
List of Tables
401
Table 190: Access to the Process Images of the Input and Output Data –
MODBUS .................................................................................................. 244
Table 191: Access to the Process Images of the Input and Output Data –
Flags ........................................................................................................... 244
Table 192: Arrangement of the I/O Modules for the Addressing Example ........ 244
Table 193: Addressing Example ......................................................................... 245
Table 194: Internal Data Bus Settings ................................................................. 251
Table 195: Errors and Remedies ......................................................................... 260
Table 196: CODESYS V3 Priorities ................................................................... 264
Table 197: MODBUS Settings ............................................................................ 268
Table 198: MODBUS TCP Settings ................................................................... 269
Table 199: MODBUS UDP Settings ................................................................... 269
Table 200: MODBUS RTU Settings ................................................................... 270
Table 201: MODBUS Mapping for Read Bit Services FC1, FC2 ...................... 275
Table 202: MODBUS Mapping for Write Bit Services FC5, FC15 ................... 276
Table 203: MODBUS Mapping for Read Register Services FC3, FC4, FC23 ... 277
Table 204: MODBUS Mapping for Write Register Services FC6, FC16,
FC22, FC23 ................................................................................................ 279
Table 205: WAGO MODBUS Registers ............................................................ 281
Table 206: Watchdog Commands ....................................................................... 285
Table 207: Watchdog Status................................................................................ 286
Table 208: Watchdog Configuration ................................................................... 287
Table 209: Diagnostics for the Error Server ....................................................... 289
Table 210: WAGO MODBUS Registers ............................................................ 293
Table 211: Watchdog Commands ....................................................................... 295
Table 212: Watchdog Status................................................................................ 296
Table 213: Watchdog Configuration ................................................................... 297
Table 214: Legend for Figure “Power Supply Indicating Elements” ................. 303
Table 215: Field-Side Supply Diagnostics .......................................................... 303
Table 216: System Power Supply Diagnistics .................................................... 303
Table 217: Diagnostics via SYS LED ................................................................. 304
Table 218: Diagnostics RUN LED ...................................................................... 305
Table 219: RUN LED Diagnostics – e!RUNTIME ............................................. 306
Table 220: Diagnostics I/O LED ......................................................................... 307
Table 221: Overview of Error Codes .................................................................. 311
Table 222: Error Code 1, Explanation of Blink Codes and Procedures for
Troubleshooting ......................................................................................... 312
Table 223: Error Code 2, Explanation of Blink Codes and Procedures for
Troubleshooting ......................................................................................... 313
Table 224: Error Code 3, Explanation of Blink Codes and Procedures for
Troubleshooting ......................................................................................... 314
Table 225: Error Code 4, Explanation of Blink Codes and Procedures for
Troubleshooting ......................................................................................... 315
Table 226: Error Code 5, Explanation of Blink Codes and Procedures for
Troubleshooting ......................................................................................... 315
Table 227: Error Code 9, Explanation of Blink Codes and Procedures for
Troubleshooting ......................................................................................... 315
Table 228: Description of Marking Example for Approved I/O Modules
According to ATEX and IECEx ................................................................ 324
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
402
List of Tables
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
Table 229: Description of Marking Example for Approved Ex i I/O Modules
According to ATEX and IECEx ................................................................ 326
Table 230: Description of Marking Example for Approved I/O Modules
According to NEC 500............................................................................... 328
Table 231: 1 Channel Digital Input Module with Diagnostics ........................... 336
Table 232: 2 Channel Digital Input Modules ...................................................... 336
Table 233: 2 Channel Digital Input Module with Diagnostics ........................... 336
Table 234: 2 Channel Digital Input Module with Diagnostics and Output
Process Data ............................................................................................... 337
Table 235: 4 Channel Digital Input Modules ...................................................... 337
Table 236: 8 Channel Digital Input Modules ...................................................... 337
Table 237: 8 Channel Digital Input Module PTC with Diagnostics and
Output Process Data ................................................................................... 338
Table 238: 16 Channel Digital Input Modules .................................................... 338
Table 239: 1 Channel Digital Output Module with Input Process Data ............. 339
Table 240: 2 Channel Digital Output Modules ................................................... 339
Table 241: 2 Channel Digital Input Modules with Diagnostics and Input
Process Data ............................................................................................... 340
Table 242: 2 Channel Digital Input Modules with Diagnostics and Input
Process Data 75x-506 ................................................................................ 340
Table 243: 4 Channel Digital Output Modules ................................................... 341
Table 244: 4 Channel Digital Output Modules with Diagnostics and Input
Process Data ............................................................................................... 341
Table 245: 8 Channel Digital Output Module ..................................................... 341
Table 246: 8 Channel Digital Output Modules with Diagnostics and Input
Process Data ............................................................................................... 342
Table 247: 16 Channel Digital Output Modules ................................................. 342
Table 248: 8 Channel Digital Input/Output Modules .......................................... 343
Table 249: 1 Channel Analog Input Modules ..................................................... 344
Table 250: 2 Channel Analog Input Modules ..................................................... 344
Table 251: 4 Channel Analog Input Modules ..................................................... 345
Table 252: 3-Phase Power Measurement Module ............................................... 346
Table 253: 8 Channel Analog Input Modules ..................................................... 346
Table 254: 2 Channel Analog Output Modules................................................... 347
Table 255: 4 Channel Analog Output Modules................................................... 347
Table 256: Counter Modules 750-404, (and all variations except of /000-005),
753-404, (and variation /000-003) ............................................................. 348
Table 257: Counter Modules 750-404/000-005 .................................................. 349
Table 258: Counter Modules 750-638, 753-638 ................................................. 349
Table 259: Pulse Width Modules 750-511, /xxx-xxx ......................................... 350
Table 260: Serial Interface Modules with alternative Data Format .................... 350
Table 261: Serial Interface Modules with Standard Data Format ....................... 351
Table 262: Data Exchange Module ..................................................................... 351
Table 263: SSI Transmitter Interface Modules ................................................... 352
Table 264: Incremental Encoder Interface Modules 750-631/000-004, --010,
-011 ............................................................................................................ 352
Table 265: Incremental Encoder Interface Modules 750-634 ............................. 353
Table 266: Incremental Encoder Interface Modules 750-637 ............................. 353
Table 267: Digital Pulse Interface Modules 750-635 ......................................... 354
Table 268: DC-Drive Controller 750-636 ........................................................... 354
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
WAGO-I/O-SYSTEM 750 XTR
750-8202/040-000 PFC200 CS 2ETH RS /XTR
List of Tables
403
Table 269: Stepper Controller RS 422 / 24 V / 20 mA 750-670 ......................... 355
Table 270: RTC Module 750-640 ....................................................................... 356
Table 271: DALI/DSI Master Module 750-641 .................................................. 356
Table 272: Overview of Input Process Image in the "Easy" Mode ..................... 358
Table 273: Overview of the Output Process Image in the "Easy" Mode“ .......... 358
Table 274: EnOcean Radio Receiver 750-642 .................................................... 359
Table 275: MP Bus Master Module 750-643 ...................................................... 360
Table 276: Bluetooth® RF-Transceiver 750-644................................................. 360
Table 277: Vibration Velocity/Bearing Condition Monitoring VIB I/O
750-645 ...................................................................................................... 361
Table 278: KNX/EIB/TP1 Module 753-646 ....................................................... 362
Table 279: AS-interface Master Module 750-655 .............................................. 363
Table 280: System Modules with Diagnostics 750-610, -611 ............................ 364
Table 281: Binary Space Module 750-622 (with Behavior Like 2 Channel
Digital Input) .............................................................................................. 364
Table 282: CODESYS System Libraries ............................................................ 365
Table 283: Possible Macros for File Access ....................................................... 367
Table 284: Possible Macros for File Access ....................................................... 368
Table 285: Input Variable “DEVICENUMBER” ............................................... 369
Table 286: Description of the Configuration Scripts for “Information” ............. 370
Table 287: Description of the Configuration Scripts for “CODESYS” .............. 371
Table 288: Description of the Configuration Scripts for
“Networking - Host/Domain Name” ......................................................... 372
Table 289: Description of the Configuration Scripts for “Networking TCP/IP” ...................................................................................................... 372
Table 290: Description of the Configuration Scripts for “Networking ETHERNET” ............................................................................................. 374
Table 291: Description of the Configuration Scripts for “NTP”......................... 375
Table 292: Description of the Configuration Scripts for “Clock”....................... 376
Table 293: Description of the Configuration Scripts for "Administration" ........ 376
Table 294: Description of Configuration Scripts for “Package Server” ............. 377
Table 295: Description of Configuration Scripts for “Ports and Services” –
“Network Services ..................................................................................... 378
Table 296: Description of Configuration Scripts for “Ports and Services” –
“PLC Runtime Services” ........................................................................... 379
Table 297: Description of Configuration Scripts for “Ports and Services” –
“SSH/TFTP” .............................................................................................. 382
Table 298: Description of Configuration Scripts for “SNMP” ........................... 383
Table 299: Overview of Open Source Licenses .................................................. 389
=== Ende der Liste für T extmar ke Verzeic hnis_hi nten ===
Manual
Version 1.1.0, valid from FW Version 02.04.22(06)
Pos : 96 /D okumentation allgemei n/Einband/Einband H andbuc h - Leers eite für durc h 2 teilbar e Seitenzahl (Standar ddr uc k) @ 3\mod_1219230851078_0.doc x @ 21123 @ @ 1
Pos : 97 /D okumentation allgemei n/Einband/Einband H andbuc h - R üc kseite 2015 @ 9\mod_1285229376516_21.doc x @ 64944 @ @ 1
WAGO Kontakttechnik GmbH & Co. KG
Postfach 2880 •
D-32385 Minden
Hansastraße 27 •
D-32423 Minden
Phone:
05 71/8 87 – 0
Fax:
05 71/8 87 – 1 69
E-Mail:
info@wago.com
Internet:
http://www.wago.com
=== Ende der Liste für T extmar ke Ei nband_hinten ===
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising