ATE-DMG - Kepco power supplies

SERIES ATE-DMG
Model ATE 6-100 DMG
ATE-DMG MODEL TABLE
MODEL
VOLTS
d-c OUTPUT
RANGE
AMPS
MAXIMUM OVERVOLTAGE
SETTING
MAXIMUM OVERCURRENT
SETTING
6.59V
16.5V
27.5V
38.3V
66V
82V
110V
185V
110A
55A
44A
33A
22A
16.5A
11A
7.7A
OUTPUT IMPEDANCE VOLTAGE MODE
SERIES R
SERIES L (1)
SLOW
FAST
OUTPUT IMPEDANCE CURRENT MODE
SHUNT R (2)
SHUNT C (3)
SLOW
FAST
SIZE "E" FULL-RACK (1000 Watt)
ATE
ATE
ATE
ATE
ATE
ATE
ATE
ATE
6-100 DMG
15-50 DMG
25-40 DMG
36-30 DMG
55-20 DMG
75-15 DMG
100-10 DMG
150-7 DMG
0-6
0-15
0-25
0-36
0-55
0-75
0-100
0-150
0-100
0-50
0-40
0-30
0-20
0-15
0-10
0-7
1.2µΩ
6µΩ
12.5µΩ
24µΩ
55µΩ
0.1mΩ
0.2mΩ
0.42mΩ
0.5µH
0.5µH
1µH
1µH
2µH
2µH
4µH
4µH
5µH
5µH
10µH
10µH
20µH
20µH
40µH
40µH
12kΩ
30kΩ
50kΩ
72kΩ
110kΩ
150kΩ
200kΩ
300kΩ
22,000µF
12,000µF
11,000µF
9,500µF
5,200µF
3,400µF
1,200µF
1,050µF
15µF
6µF
4µF
3µF
2.25µF
1.5µF
0.75µF
0.3µF
(1) For the calculation of dynamic impedance in voltage mode.
(2) Based on 0.5mA load effect in FAST mode.
(3) For the calculation of dynamic impedance in current mode.
Kepco's 1000 watt instrument-grade
digital power supplies, series ATE-DMG,
are linear low-noise power supplies
designed to respond very quickly and
precisely to voltage and current setting
instructions delivered interactively by
the GPIB (IEEE 488.2) or from a front
panel keypad. When programmed from
the bus, the ATE-DMG power supplies
respond to the SCPI (Standard Commands
for Programmable Instruments) common
language for instruments
used in an automatic
test system.
ATE-DMG digital power supplies are locally controlled exclusively
through a 24-key panel keypad. This offers full control over the
voltage and current settings, as well as overvoltage, overcurrent and
a time setting. The keypad allows the user to store as many as 40
combinations of these parameters and to loop back onto itself to
produce repetitive programs. The setting values as well as the actual
output delivered to the load are displayed in the two-line, 16 character
back-lit LCD.
Remote control is via the built-in IEEE-488.2 interface that offers
full talk-listen functionality on the bus. The settings and the actual
voltage-current values are read back on the bus upon command. The
output can be modulated by analog signals in the same fashion as
Kepco's non-digital ATE-series power supplies. The ATE-DMG
retains the ATE-series' signature high-speed control mode which
enables rapid output programming and fast voltage recovery to load
changes in current-control mode.
ATE-DMG are CE marked per the
Low Voltage Directive (LVD), EN61010-1.
28
KEPCO, INC. • 131-38 Sanford Avenue • Flushing, NY 11352 USA • Tel: (718) 461-7000 • Fax: (718) 767-1102
Email: hq@kepcopower.com • www.kepcopower.com/atedg.htm
FEATURES
• Linear control for low noise: 100 microvolts typical in voltage mode; and high
precision: 0.0005% source effect {regulation}
in voltage mode.
• Voltage and current control with equivalent
performance. A high speed mode allows
fast-recovery current-controlled stabilization
into a varying load.
• Overvoltage and overcurrent settings
individually programmed by the front
panel keypad or remotely by the bus with
a programmable delay to allow for reactiveload transients.
• A manually set overvoltage crowbar
monitors the output to protect sensitive
loads. This setting is done only from the
front panel and cannot be modified by the
keypad or GPIB.
Rear View of Model ATE 6-100 DMG
The dynamic characteristics are tabulated in the Dynamic
Specifications Table. Analog control of voltage and current is via a pair
of remote signals (0-10V for voltage, 0-1V for current). Two uncommitted
op-amps are provided internally to allow available control signals
to be scaled and, if necessary, inverted to suit the circumstances.
6V
15V
25V
36V
55V
75V
100V
150V
PROGRAMMING BANDWIDTH (KHz)
Typical
minimum
23.0
20.0
11.5
8.0
4.8
4.3
2.7
1.8
• Full talk-listen control from a GPIB
(IEEE 488-2) using SCPI language.
• Master-slave series and parallel operation
to provide increased capability.
ATE-DMG DYNAMIC SPECIFICATIONS
OUTPUT VOLTAGE
RATING
• Non-volatile storage of programmed
sequences or active settings. The ATE-DMG
contains 40 memory locations that store
voltage, current, overvoltage, overcurrent,
time (how long the parameters are in effect)
and the next address in the sequence.
PROGRAMMING TIME CONSTANT (µsec)
Typical
maximum
16.0
10.6
8.0
6.4
4.0
3.5
2.5
1.7
7.0
8.0
14.0
20.0
33.0
37.0
60.0
88.0
10.0
15.0
20.0
25.0
40.0
45.0
65.0
95.0
• Local control: Front panel keypad entries are
used for setting and adjusting the output. The
keypad can be used to execute commands
directly or to introduce a program to be run
later or cycled. Calibration of the ATE-DMG
is done from the keypad using a passwordprotected, menu-driven procedure.
ATE-DMG STATIC SPECIFICATIONS
INFLUENCE QUANTITY
Source Voltage (min.-max.)
Load (no load-full load)
Time (8-hour drift)
Temperature, per °C
Ripple and Noise (2)
rms:
(Slow Mode)
p-p:(3)
Ripple and Noise (2)
rms:
(Fast Mode)
p-p:(3)
OUTPUT EFFECTS VOLTAGE MODE
Typ.
Max.
<0.0005% Eo max.
<0.001% Eo max.
<0.005% Eo max.
<0.005% Eo max.
<0.1mV
<1mV
<1mV
<10mV
0.001% Eo max.
0.002% Eo max.
0.01% Eo max.
0.01% Eo max.
0.3mV
3mV
3mV
30mV
OUTPUT EFFECTS CURRENT MODE
Typ.
Max.
<0.002% Io max.
<0.5 mA(1)
<0.01% Io max.
<0.01% Io max.
<0.01% Io max.
<0.1% Io max.
<0.01% Io max.
<0.1% Io max.
0.005% Io max.
1 mA(1)
0.02% Io max.
0.02% Io max.
0.03% Io max.
0.3% Io max.
0.03% Io max.
0.3% Io max.
∆Eio
<1µV
—
<20µV
<20µV
—
—
—
—
OFFSETS
∆Iio
<1nA
—
<1nA
<2nA
—
—
—
—
(1) For Io>50A, load effect = 2mA typ., 5mA max. In slow mode, the output capacitor adds 0-6mA to current mode load effect.
(2) One terminal grounded so that common mode current does not flow through load or current-sense resistor.
(3) BW: 20Hz-10MHz.
.
AN ISO 9001 COMPANY
KEPCO, INC. • 131-38 Sanford Avenue • Flushing, NY 11352 USA • Tel: (718) 461-7000 • Fax: (718) 767-1102
Email: hq@kepcopower.com • www.kepcopower.com/atedg.htm
29
OUTLINE DIMENSIONAL DRAWINGS
Fractional dimensions in light face type are in inches,
dimensions in parentheses are in millimeters.
Tolerance: ± 1/64" (0.4) between mounting holes
± 1/32" (0.8) other dimensions
ATE-DMG GENERAL SPECIFICATIONS
SPECIFICATI0N
RATING/DESCRIPTION
INPUT
a-c Voltage
95-113, 105-125, 190-226,
210-250V a-c
20A a-c
47-65Hz
Current
Frequency
OUTPUT
d-c Output
Voltage
Current
REAR VIEW
Series pass
0-100% of rated voltage
0-100% of rated current
CONDITION
User selectable
Max load, 125V a-c
Range
Transistor
Usable range limited to approx.
1% to 100%.Max.current is factory
set to 105% of rated output current.
Type of Stabilizer
Voltage
Current
Automatic crossover
Voltage/current
0 to 100% of rating
Adjustment range
for temp 0-55°C
0 to 100% of rating
0 to 90% of rating
For temp 65°C
Storage Temp. Range
(_)40°C to 85°C
Error Sense
0.5V per load wire(1)
Voltage allowance
Isolation Voltage
500V d-c or peak
Output to ground
Leakage Current
<5 microamperes
rms at 115V a-c
Output to Ground
<50 microamperes
p-p at 115V a-c
Series Connection
500V
Max voltage off ground
Parallel
Automatic
Use current mode limiting
Connection
Current sharing
Use master-slave connection
Redundancy type
External or-ing diodes
OVP
Type
Crowbar
Control Local or program or track
Trigger time
50 microseconds
Normal
Trigger time
500 microseconds
Delayed
Threshold Min. 0.5 volts, or 2% Eo max.
Whichever is greater
Temp. coefficient <0.02% of Eo max. per °C
CONTROL
Program.
Voltage
<0.025% Eo max
Accuracy
Current
<0.25% Io max
Readback/display
Accuracy Voltage
<0.05% Eo max
Current
<0.275% Io max
Voltage
Remote
12-bit digital
Current
Limit 10-turn precision rheostat
Remote
12-bit digital
Programming Time
1.2ms max
0-100%
Front panel
Data Entry
Local
24 keypads
Remote
GPIB
SCPI commands
Dynamics
See tabulated value of C
in the model table
Normal (slow)
dV/dt = I/C
Fast mode
See Table
Dynamic spec table
MECHANICAL
Weight
96lb (43.6Kg)
Packed for shipment
Dimensions inches
631⁄32 x 19 x 201⁄64
Full rack size
mm
177 x 482.6 x 504.8
a-c Source
Terminal block
Connections
TOP VIEW
FRONT VIEW
d-c Output
Connections
SIDE VIEW
(1) 0-6V models: 0.25V.
User Port
Indicators
Remote Control
Programming
Digital Display
Front Panel
KEPCO, INC.
131-38 Sanford Avenue, Flushing, NY 11352 USA
Tel: (718) 461-7000 • Fax: (718) 767-1102
Email: hq@kepcopower.com
30
www.kepcopower.com/atedg.htm
Rear binding post
Rear compression studs
50-terminal connector
Three LEDs
One standard
GPIB connector
I <30A
°
I ≥30A
°
Voltage/Current/OVP
Rear, SCPI &
IEEE 488.2 commands
Voltage, current, mode
2 x 16 character alphanumeric
status, menu, program, etc.
LCD with LED backlight
Mounting
(in std 19" racks)
Cooling
Mounting “ears” supplied
Forced air
High efficiency, single bearing
fans, permanently lubricated
with special low-noise
metallic blades. Exhaust to rear.
Finish: Fed Std 595
Dark & light gray, color 26440
Front panel, 2 tone

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project