Modell Disc-7990 Encode
Modell Disc-7990 Encode
Bitte vor Inbetriebnahme sorgfälltig lessen
Read instructions carefully before using the unit
Avant de metre en service votre appareil, lisez attentivement ce instructions
Encode
Sicherheits- / Umwelt- / Aufstellhinweise
•
Das Gerät ausnahmslos nur in trockenen Innenräumen betreiben.
•
Niemals mit Feuchtigkeit in Verbindung bringen
•
Niemals das Gerät öffnen. STROMSCHLAGGEFAHR ! Dies ist nur Fachpersonal gestattet.
•
Bei Gewitter, Netzstecker sofort aus der Steckdose entfernen.
•
Bei Beschädigung des Netzkabels, Netzstecker sofort ziehen und eine Fachwerkstatt aufsuchen.
•
Kinder sollten das Gerät nur unter Aufsicht Erwachsener betreiben.
•
Das Gerät ausnahmslos nur mit einem trockenen Tuch reinigen. KEINE REINIGUNGSMITTEL !!!
•
Das Gerät keiner Sonnenbestrahlung oder anderen Hitzequellen aussetzten.
•
Das Gerät an einem sicheren, erschütterungsfreien Platz aufstellen.
•
Rund um das Gerät min. 10cm Entlüftungsraum auf jeder Seite frei halten, so das die bei Betrieb
entstehende Warmluft ungehindert abziehen kann
•
Gerät möglichst weit entfernt von Computern und Mikrowellengeräten platzieren, da es sonst evtl. zu
Empfangsstörungen im Radiobetrieb kommen kann.
•
Bei Wandmontage sicher montieren, um ein herunterfallen zu vermeiden.
•
Verwenden Sie nur Batterien für die Fernbedienung, die frei von Quecksilber & Cadmium sind.
•
Verbrauchte Batterien sind Sonderabfall und gehören NICHT in den Hausmüll !! Geben Sie diese Ihrem
Händler zurück oder entsorgen Sie diese an geeigneten Sammelstellen Ihrer Stadt oder Gemeinde.
Technische Daten
Netzbetrieb
AC 230V 50Hz
Leistungsaufnahme
38 W
Lautsprecher
4 ohm
Musikspitzenleistung
2 x 50W P.M.P.O
UKW / FM
87,5 – 108 MHz
MW / AM
520 – 1710 KHz
QUICK START !
1. CONNECT THE SPEAKERS & TABLE STANDS
2. PLUG AC-CORD INTO WALL SOCKET & UNWRAP THE FM-ANTENNA WIRE
DIGITAL
DIGITAL
2 WAY POWER BASS ARCHITECTURE
2 WAY POWER BASS ARCHITECTURE
FM-ANTENNA WIRE
AC-CORD
3. PRESS “ON/OFF” KEY
TO SWITCH “ON” THE UNIT
4. TO LISTEN TO CD-PLAYER
- PRESS "CD" KEY
- PRESS "OPEN (CD)" KEY
- INSERT A DISC (CD-AUDIO or CD-MP3)
- PRESS "PLAY" KEY (
) TO START
PLAYING CD
- ADJUST VOLUME (VOL+) or (VOL )
P
RI
A
D
RD
S
N T SI
E
OUTW
(CONTINUED)
E-3
(CONTINUED)
5. TO LISTEN TO RADIO
PRESS "NEXT" TO TUNE UP
PRESS "BACK" TO TUNE DOWN
-
PRESS "RADIO" KEY TO SWITCH TO RADIO (TUNER) MODE
PRESS "RADIO" KEY TO SWITCH TO "FM" RADIO BAND.
PRESS "RADIO" KEY AGAIN TO SWITCH TO "MW" (AM) RADIO BAND.
PRESS & RELEASE NEXT TO TUNE RADIO FREQUENCY UP (1-STEP).
PRESS & RELEASE BACK TO TUNE RADIO FREQUENCY DOWN (1-STEP).
“PRESS & HOLD” NEXT (2 SECS.) TO SCAN UP (TO SEEK NEXT STATION).
“PRESS & HOLD” BACK (2 SECS.) TO SCAN DOWN (TO SEEK PREV. STATION).
6. TO LISTEN TO CASSETTE TAPE
- PRESS "TAPE" KEY
- PRESS "OPEN (TAPE)" KEY
- INSERT A CASSETTE
(TAPE SIDE FACING DOWN)
- PRESS "PLAY" KEY (
) TO START
PLAYING TAPE
- ADJUST VOLUME (VOL+) or (VOL )
END
E-4
LOCATION OF CONTROLS
1
9
10
11
12
13
1
14
15
2
16
33
17
18
19
3
34
20
21
4
35
22
36
23
5
24
37
25
26
6
27
28
29
8
30
31
32
6
7
INSIDE OF THE CASSETTE COMPARTMENT:
38
1. SPEAKER (LEFT & RIGHT)
2. CD DOOR
3. CD/ CLOCK/ RADIO DIGITAL
MULTIFUNCTION DISPLAY
4. ON/ OFF KEY
5. CASSETTE DOOR
6. DESK STANDS (FOR SPEAKERS)
7. AC CORD & PLUG
8. DESK STAND (FOR MAIN UNIT)
9. CD PLAY/ PAUSE KEY
10. CD "STOP" KEY
11. CD "NEXT" KEY
12. CD "BACK" KEY
13. PRESET/ FOLDER UP KEY
14. PRESET/ FOLDER DOWN KEY
15. REPEAT/ SEARCH KEY
16. FIND/ DISPLAY KEY
17. REMOTE CONTROL SENSOR
18. OPEN (CD) KEY
19. VOLUME UP KEY
20. VOLUME DOWN KEY
21. OPEN (TAPE) KEY
39
40
41
42
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
RADIO KEY
CD KEY
CLOCK/ PROGRAM KEY
TAPE KEY
EQ KEY
AUX KEY
REC KEY
USB/ SD KEY
SD-CARD SOCKET
USB SOCKET
FM-ANTENNA WIRE
BACK UP BATTERY COMPARTMENT
(BEHIND THE UNIT)
34. SUB WOOFER OUTPUT
35. AUDIO LINE IN SOCKET [AUX]
(LEFT & RIGHT)
36. HEADPHONE JACK
37. SPEAKER-OUT SOCKET (LEFT & RIGHT)
38. CASSETTE "PLAY" KNOB
39. CASSETTE "REW" KNOB
40. CASSETTE "F.FWD" KNOB
41. CASSETTE "STOP" KNOB
42. CASSETTE "PAUSE" KNOB
E-5
1
2
7
3
8
4
9
5
10
6
11
12
13
14
15
17
16
19
18
REMOTE CONTROL
LOCATION OF REMOTE CONTROLS
1. ON/ OFF BUTTON
2. FIND/ M/S KEY
3. TIMER KEY
4. EQ KEY
5. SLEEP KEY
6. MEMORY DOWN KEY
7. BAND KEY
8. INTRO KEY
9. FUNCTION KEY
10. REPEAT KEY
11. MEMORY UP KEY
12. DIRECT KEYS (NUMBER KEYS)
13. MUTE KEY
14. MEMORY/ PROGRAM KEY
15. CD PLAY/ PAUSE KEY
16. CD NEXT/ TUNE UP KEY
17. CD BACK/ TUNE DOWN KEY
18. CD STOP KEY
19. VOLUME UP KEY
20. VOLUME DOWN KEY
20
POWER SUPPLY
-
THIS SET WORKS ON NORMAL HOUSEHOLD AC-POWER.
MAKE SURE THE SET VOLTAGE OF THE UNIT MATCHES YOUR LOCAL VOLTAGE.
INSERT THE PLUG OF THE AC-CORD INTO A WALL OUTLET WITH AC-POWER.
PRESS THE ON/ OFF KEY TO SWITCH “ON” THE UNIT.
IMPORTANT : HOW TO TELL IF POWER IS "ON" ?
WHEN THE POWER IS "ON" THE ENTIRE DIGITAL DISPLAY WILL LIT UP WITH
A "BLUE" BACK-LIGHT. THIS INDICATES THE HI-FI IS SWITCHED "ON".
- THIS UNIT IS DESIGNED TO OPERATE WITHOUT BEING TOTALLY POWERED "OFF".
IT WILL EITHER BE "ON" OR IN "STANDBY” MODE.
- IN “STANDBY” MODE, THE BLUE BACK-LIGHT OF THE DIGITAL DISPLAY WILL BE
SWITCHED OFF BUT THE DISPLAY WILL SHOW THE CURRENT TIME (CLOCK FUNCTION).
- WHEN IN STANDBY MODE, YOU CAN USE THE POWER SWITCH (ON REMOTE CONTROL
OR ON FRONT PANEL OF THE MAIN UNIT) TO SWITCH "ON" THE UNIT.
- TO CONSERVE ELECTRICITY, PLEASE SWITCH THE UNIT TO "STANDBY MODE"
WHEN NOT USING THE UNIT.
BACK UP BATTERIES
- OPEN THE BATTERY DOOR AT THE REAR OF UNIT.
- INSERT 2 PCS "AA-CELL" (UM-3/LR6 TYPE) BATTERIES IN THE BATTERY COMPARTMENT.
THESE 2 BATTERIES ARE FOR BACKUP OF THE "REAL TIME CLOCK" AND "RADIO
MEMORY PRESET STATIONS DURING BRIEF POWER OUTAGES". PLEASE OBSERVE THE
CORRECT POLARITIES OR THE MEMORY WILL NOT BE PROPERLY MAINTAINED.
CONNECTION OF SPEAKER BOXES
- UNWRAP THE SPEAKER-CORDS OF BOTH SPEAKER-BOXES.
- PLEASE NOTICE THAT EACH SPEAKERS CORD CONSISTS OF 2 WIRES, ONE IS "CLEAR"
AND ONE HAS A BLACK LINE.
- INSERT THE "CLEAR" WIRE OF THE LEFT SPEAKER-BOX INTO THE "RED" ( + ) SPEAKER
CONNECTOR BESIDE THE MAIN-UNIT, WHICH HAS THE "L" INDICATION (NEXT TO THE
SPEAKER-CONNECTOR).
- INSERT THE "BLACK" WIRE OF THE LEFT SPEAKER-BOX INTO THE "BLACK" ( - )
SPEAKER CONNECTOR BESIDE THE MAIN-UNIT, WHICH HAS THE "L" INDICATION
(NEXT TO THE SPEAKER-CONNECTOR).
- REPEAT THE ABOVE 2 STEPS FOR THE "RIGHT" SPEAKER BOX, BUT THIS TIME,
INSERTING THEM INTO THE RED & BLACK CONNECTORS WHICH HAVE
THE "R" INDICATION.
- WHEN INSERTING EACH WIRE INTO A CONNECTOR, PRESS DOWNWARDS ON
THE CONNECTOR'S PLASTIC KNOB (RED OR BLACK PART) & PUSH THE EXPOSED
METAL END OF THE WIRE ALL THE WAY INTO THE HOLE ABOVE THIS KNOB.
- PLACE THE SPEAKER BOXES AS FAR APART AS POSSIBLE FOR BEST SOUND EFFECT.
E-6
DIGITAL CLOCK FUNCTION
HOW TO SET CORRECT TIME:
- THE SET HAS A BUILT-IN DIGITAL CLOCK, WHICH IS DISPLAYED WHEN THE UNIT IS IN "STANDBY
MODE" OR WHEN YOU PRESS & HOLD PROGRAM KEY FOR TWO SECONDS DURING CD OR RADIO
OPERATION.
- TO SET THE CORRECT TIME, FOLLOW THIS PROCEDURE:
SWITCH UNIT TO "STAND-BY" MODE (DISPLAY LIGHT = OFF)
PRESS & HOLD PROGRAM FOR 3 SECONDS
DISPLAY SHOWS 12 HOUR OR 24 HOUR (FLASHING)
PRESS NEXT OR BACK TO SELECT 12-HOUR
OR 24-HOUR CLOCK DISPLAY SYSTEM & PRESS
PROGRAM TO CONFIRM YOUR SELECTION
PRESS NEXT OR BACK REPEATEDLY TO SET THE
CORRECT HOUR IN THE DISPLAY & PRESS PROGRAM
TO CONFIRM
PRESS NEXT OR BACK REPEATEDLY TO SET THE
CORRECT MINUTE IN THE DISPLAY & PRESS PROGRAM
TO CONFIRM
CORRECT TIME IS NOW SET & WILL BE SHOWN IN THE DISPLAY!
E-7
AUTOMATIC POWER ON/OFF TIMER FUNCTION
- THIS SET HAS A TIMER FUNCTION WHICH ENABLES YOU TO PROGRAM THE UNIT TO
SWITCH "ON" OR "OFF" AUTOMATICALLY AT PRESET TIMES. THIS IS USEFUL AS A MORNING
ALARM CLOCK .
- IMPORTANT: PLEASE NOTE THAT THE TIMER KEY USED TO PROGRAM THIS SPECIAL
FUNCTION IS LOCATED ONLY ON THE REMOTE CONTROL.
HOW TO SET TIMER
1. PRESS AND HOLD TIMER . THE TIMER ON SYMBOL WILL APPEARS IN THE DISPLAY.
2. PRESS NEXT OR BACK TO SET THE HOUR OF THE DESIRED "POWER ON" TIME
AND THEN PRESS TIMER TO CONFIRM.
3. PRESS NEXT OR BACK TO SET THE MINUTES OF THE DESIRED "POWER ON"
TIME AND THEN PRESS TIMER TO CONFIRM.
4. NOW THE SYMBOL IN THE DISPLAY CHANGES TO SHOW TIMER OFF
.
5. PRESS NEXT OR BACK TO SET THE HOUR OF THE DESIRED "POWER OFF"
TIME AND THEN PRESS TIMER TO CONFIRM.
6. PRESS NEXT OR BACK TO SET THE MINUTES OF THE DESIRED "POWER OFF"
TIME AND THEN PRESS TIMER TO CONFIRM.
7. NOW THE DISPLAY WILL INDICATE THE "WAKE UP MODE" (CD OR RADIO).
PRESS NEXT TO CHOOSE THE DESIRED MODE & PRESS TIMER TO CONFIRM
8. THE DISPLAY THEN SHOWS THE "WAKE UP VOLUME LEVEL" (LOUNDNESS).
PRESS NEXT OR BACK TO DECREASE OR INCREASE THE VOLUME LEVEL TO BE
USED FOR THE MUSIC TO BE PLAYED WHEN THE TIMER SWITCHES ON THE UNIT AT THE
PRE-SET TIME.
9. PRESS TIMER TO SET THE VOLUME LEVEL OF THE UNIT WHEN IT SWITCHES ON AT THE
PRE-SET TIME:
"POWER ON TIME" (
ON
"POWER OFF TIME" (
OFF )
)
"POWER ON MODE" (CD OR TUNER)
"POWER ON VOLUME LEVEL" (LOUDNESS)
10. THE DISPLAY WILL THEN RETURN TO NORMAL, AND THE SYMBOL “TIMER” WILL BE
DISPLAYED, TO INDICATE THAT YOU HAVE PROGRAMMED A POWER ON/OFF ALARM
SETTING.
11. IN CASE YOU WISH TO DISABLE THE TIMER, PRESS TIMER & THE “TIMER” SYMBOL
DISAPPEARS.
(NOTE : THE AUTOMATIC POWER ON/OFF TIMER WILL SWITCHES ON THE UNIT AS IF YOU HAVE
MANUALLY PRESSED THE ON/OFF KEY. IF YOU HAVE SELECTED "WAKE TO RADIO",
THE EXACT PRESET RADIO BAND & STATION WILL BECOME ACTIVATED WHEN POWER
SWITCHES ON).
AUTOMATIC POWER OFF SLEEP FUNCTION
- THIS SET HAS A SPECIAL SLEEP TIMER FUNCTION WHICH IS ABLE TO SWITCH OFF
THE UNIT AUTOMATICALLY. THIS IS USEFUL FOR SLEEPING MUSIC AT NIGHT.
- AT ANY TIME WHILE THE UNIT IS OPERATING (CD PLAYER OR RADIO), PRESS SLEEP
KEY REPEATEDLY TO CHOOSE THE AUTOMATIC POWER OFF TIME.
90
MINS
80
MINS
70
MINS
60
MINS
50
MINS
40
MINS
(*OFF MEANS SLEEP TIMER IS DEACTIVATED)
E-8
30
MINS
20
MINS
10
MINS
OFF*
ELECTRONIC VOLUME CONTROL
- THIS UNIT USES AN ELECTRONIC VOLUME CONTROL (PUSH BUTTON TYPE) .
- TO INCREASE OR DECREASE THE LOUDNESS OF UNIT, PRESS AND HOLD THE VOLUME UP (VOL +)
OR VOLUME DOWN (VOL -) KEYS RESPECTIVELY.
- RELEASE THE KEY WHEN VOLUME LEVEL IS AT THE DESIRED LOUDNESS.
- SOMETIMES, ESPECIALLY DURING LISTENING TO THE RADIO, YOU MAY NOTICE
A "CLICK-CLICK-CLICK" (REPEATING) SOUND WHEN YOU ARE INCREASING OR DECREASING
THE VOLUME. THIS IS A NORMAL CONDITION & THE SOUND WILL DISAPPEAR WHEN YOU
RELEASE THE VOLUME KEY (WHEN YOU REACH THE DESIRED VOLUME LEVEL).
MUSIC EQUALIZER
- PRESS EQ KEY REPEATEDLY TO CHOOSE THE DESIRED SOUND EFFECT ACCORDING TO THE
MUSIC YOU ARE LISTENING TO :
*PASS
CLASSIC
ROCK
POP
JAZZ
(*PASS MEANS EQUALIZER IS "BY-PASSED" OR "OFF")
OPERATION OF RADIO
-
PRESS THE "ON/OFF" KEY ONCE TO SWITCH ON THE UNIT.
PRESS THE RADIO KEY TO SELECT THE RADIO FUNCTION.
FOR MW (AM) STATIONS, ROTATE OR REPOSITION THE SET TO IMPROVE RADIO RECEPTION.
TO IMPROVE FM-RADIO RECEPTION, FULLY EXTEND THE FM-ANTENNA WIRE AND ADJUST
IT'S POSITION.
- USE THE "M/S" KEY (ON REMOTE CONTROL) TO SELECT THE DESIRED MODE ( FM MONO/STEREO) .
IN SOME CASES, WHERE RECEPTION IS POOR, IT MAY BE ADVISABLE TO SELECT “MONO” MODE,
TO IMPROVE CLARITY OF THE RADIO SIGNAL.
MANUAL FREQUENCY ADJUSTMENT (SCAN MODE)
- PRESS (AND IMMEDIATELY RELEASE) THE NEXT OR BACK KEY TO “SCAN” (MANUALLY
ADJUST) THE RADIO FREQUENCY BY 1-STEP AT A TIME.
- THE RADIO DIGITAL DISPLAY WILL INDICATE THE EXACT FREQUENCY AT EACH POSITION.
- WHEN A DESIRED FREQUENCY OR STATION IS REACHED. IT CAN BE SAVED INTO ONE OF THE
“MEMORY”STORAGE. (SEE “RADIO MEMORY” SECTION).
AUTOMATIC FREQUENCY ADJUSTMENT (SEEK MODE)
- PRESS AND HOLD NEXT OR BACK (FOR 2 SECONDS) TO “SEEK” FOR (AUTOMATICALLY
ADJUST) THE RADIO FREQUENCY TO THE NEXT AVAILABLE RADIO STATION.
- THE RADIO DIGITAL DISPLAY WILL INDICATE THE EXACT FREQUENCY OF THE STATION THAT IS
FOUND.
- WHEN A DESIRED STATION IS REACHED. IT CAN BE SAVED INTO ONE OF THE “MEMORY”.
(SEE “RADIO MEMORY” SECTION).
RADIO MEMORY (STATION PRESET MEMORY STORAGE)
- AT ANY TIME, THE PRESENT DISPLAYED STATION OR FREQUENCY CAN BE STORED INTO THE
MEMORY POSITION.
- PRESS PROGRAM KEY ONCE.
- PRESS UP OR DOWN TO SELECT DESIRED FREE MEMORY POSITION.
(THERE ARE 10 MEMORY POSITIONS FOR AM BAND & 30 MEMORY POSITIONS FOR FM BAND).
- PRESS PROGRAM KEY ONCE TO SAVE THE SELECTED STATION INTO THE SELECTED MEMORY
POSITION.
- TO RECALL ANY SAVED MEMORY, SIMPLY PRESS UP OR DOWN , THE SAVED RADIO-BAND
WILL BE RECALLED.
- TO ERASE ANY PARTICULAR MEMORY, SIMPLY SAVE A NEW STATION TO OVERWRITE THE
UNWANTED MEMORY.
RDS (RADIO DATA SYSTEM)
THIS UNIT HAS "RDS" FUNCTION, IN FM MODE. PRESS THE NEXT OR BACK KEY TO SEARCH
STATIONS. EVERYTIME WHEN IT FINDS A STEADY STATION, THE "RDS" ICON LIGHTS UP AND
THE STATION NAME APPEARDS IN THE LCD DISPLAY. THIS FUNCTION IS ONLY ACTIVE FOR
THOSE STATIONS WHICH HAVE "RDS" TRANSMISSION, AND ALSO MUST BE IN A GOOD
RECEPTION AREA.
E-9
CASSETTE TAPE PLAYBACK
- PRESS TAPE TO SELECT THE CASSETTE TAPE FUNCTION.
- OPEN THE CASSETTE DOOR BY PRESSING OPEN (TAPE) .
- INSERT A PRE-RECORDED CASSETTE WITH THE TAPE-SIDE DOWN, PUSH IT
TOWARD THE UNIT WITH PLACING IT AT THE RIGHT POSITION AND MAKE SURE THE TAPE
IS FULLY AND PROPERLY INSERTED.
- PRESS PLAY (LOCATED BELOW THE CASSETTE TAPE SLOT) TO START THE CASSETTE
PLAYBACK. NOTE THAT THE TAPE MOVES FROM LEFT TO RIGHT.
- ADJUST THE VOLUME TO THE DESIRED LEVEL.
- THE TAPE PLAYBACK CAN BE STOPPED AT ANYTIME, SIMPLY PRESS THE STOP
BUTTON BELOW THE CASSETTE TAPE SLOT. AT THE TAPE'S END, THE SET SWITCHES
ITSELF OFF AUTOMATICALLY, AND RELEASES THE PLAY BUTTON AT THE SAME TIME.
- PRESS THE "STOP" BUTTON FOLLOWED BY THE "REWIND" OR "FAST-FORWARD"
BUTTON TO REWIND OR FORWARD THE TAPE AT HIGH SPEED.
- TO PAUSE THE CASSETTE FROM PLAYING, SIMPLY PRESS PAUSE AT ANYTIME DURING
CASSETTE PLAYBACK.
- PRESS THE "STOP" KEY FOLLOWED BY THE "REWIND" OR "FAST-FORWARD" BUTTON TO REWIND
OR FORWARD THE TAPE AT HIGH SPEED.
COMPACT DISCS (CD) PLAYBACK
INSERTION AND REMOVAL OF DISCS:
PRESS CD TO SELECT THE CD FUNCTION.
PRESS THE OPEN (CD) KEY TO OPEN THE CD-DOOR. CAREFULLY PLACE COMPACT DISC
(CD OR MP3 DISC) ONTO THE CENTER SPINDLE WITH THE LABEL SIDE (PRINTED SIDE OF DISC)
FACING OUTWARDS (TOWARDS YOU). PRESS THE OPEN (CD) BUTTON TO CLOSE THE CD-DOOR.
THE CD-DISPLAY WILL SHOW THE TOTAL NUMBER OF TRACKS ON THE DISC AFTER A FEW SECONDS.
THE CD IS NOW READY TO BE PLAYED. TO REMOVE A DISC, PRESS THE OPEN/ CLOSE KEY.
THE DOOR WILL OPEN UPWARDS ALLOWING THE REMOVAL OF THE CD INSIDE.
IMPORTANT: ALWAYS HOLD A CD BY IT'S EDGES. AVOID GETTING ANY FINGER-PRINTS,
SMUDGES OR DIRT ONTO THE SURFACE OF A DISC. IN CASE THIS HAPPENS,
USE A SPECIAL CD-CLEANING CLOTH OR CLEANING KIT TO REMOVE THE DIRT OR
SMUDGES.
NORMAL CD OPERATION
-
PRESS "ON/OFF" KEY TO SWITCH ON THE UNIT.
PRESS THE "FUNCTION" KEY REPEATEDLY UNTIL THE DISPLAY SHOWS "CD"
PRESS THE "OPEN/ CLOSE" KEY & INSERT A CD AS DESCRIBED.
PRESS PLAY KEY. THE DISK WILL START SPINNING & THE FIRST SONG (TRACK) WILL START
PLAYING. THE DISPLAY WILL INDICATE THE CURRENT TRACK NO.
- AT ANYTIME DURING PLAYBACK, PRESS PLAY TO PAUSE THE OPERATION. PRESS PLAY
AGAIN TO RESUME.
- AT ANYTIME DURING PLAYBACK, PRESS STOP TO STOP THE OPERATION. THIS WILL RESET
THE CD AND PREPARE PLAYING FROM THE BEGINNING
- AT ANYTIME DURING PLAYBACK, PRESS AND RELEASE NEXT OR BACK TO SKIP FORWARD
OR BACKWARDS BY ONE TRACK, AS DESIRED.
- AT ANYTIME DURING PLAYBACK, PRESS AND HOLD NEXT OR BACK TO FAST-FORWARD (CUE)
OR FAST-REVERSE (REVIEW) THE SPECIFIC TRACK, WHICH IS CURRENTLY PLAYING.
E-10
PROGRAMMING THE CD-PLAYER
- THE CD PLAYER CAN BE PROGRAMMED IN ANY PLAYING SEQUENCE OF UPTO 64 TRACKS,
AS DESIRED.
- ALWAYS PRESS STOP BEFORE PROGRAMMING.
- PRESS THE PROGRAM KEY ONCE, THE DISPLAY WILL SHOW THE “MEMORY” SYMBOL TO
INDICATE THAT THE SET IS NOW IN “MEMORY PROGRAMMING MODE”.
FOR NORMAL CD-AUDIO DISCS:
- PRESS NEXT OR BACK TO SELECT THE TRACK (SONG)
NUMBER YOU WISH TO BE PLAYED FIRST IN THE DESIRED PLAYING SEQUENCE.
- PRESS THE PROGRAM KEY TO CONFIRM YOUR SELECTION.
- REPEAT THE PREVIOUS 2 STEPS, EACH TIME SELECTING ANY TRACK NUMBER OF YOUR
CHOICE IS PROGRAMMED IN A PLAYING SEQUENCE.
- AFTER A MAXIMUM OF 64 SONGS (OR LESS) HAVE BEEN SELECTED AS DESCRIBED ABOVE,
PRESS PROGRAM KEY, THE DISPLAY WILL NOW SHOW MEMORY TO INDICATE THAT YOU HAVE
SAVED A PROGRAM-MEMORY.
- PRESS PLAY KEY, THE CD-PLAYER WILL PLAYBACK THE “SAVED SEQUENCE” IN THE
PROGRAM MEMORY.
- TO CLEAR (CANCEL) THE ENTIRE PROGRAM WHICH IS STORED IN THE MEMORY, SIMPLY
PRESS STOP KEY, THIS WILL RESET THE MEMORY & CLEAR THE PROGRAM.
FOR CD-MP3 DATA DISCS:
- PRESS THE NEXT OR BACK TO SELECT THE ALBUM (FOLDER DIRECTORY)
NUMBER WHICH CONTAINS THE SONG YOU WISH TO SELECT
- PRESS THE PROGRAM KEY TO CONFIRM YOUR SELECTION.
- PRESS THE NEXT OR BACK TO SELECT THE TRACK (SONG) NUMBER YOU WISH TO BE
STORED IN THE CURRENT MEMORY (PROGRAM) POSITION.
- PRESS THE PROGRAM BUTTON TO CONFIRM YOUR SELECTION.
- REPEAT THE PREVIOUS 4 STEPS, EACH TIME SELECTING ANY ALBUM AND TRACK NUMBER OF
YOUR CHOICE TO BE STORED IN SUCCESSIVE (PROGRAM) POSITIONS.
- AFTER A MAXIMUM OF 64 SONGS (OR LESS) HAVE BEEN SELECTED AS DESCRIBED ABOVE,
PRESS PROGRAM KEY, THE DISPLAY WILL NOW SHOW MEMORY TO INDICATE YOU HAVE SAVED
A PROGRAM-MEMORY.
- PRESS PLAY KEY, THE CD-PLAYER WILL PLAYBACK THE “SAVED SEQUENCE” IN THE
PROGRAM MEMORY.
- PRESS STOP KEY TO ESCAPE MEMORY PLAYBACK TEMPORARILY.
- PRESS CLOCK/PROGRAM TO RESUME MEMORY PLAYBACK.
- TO MODIFY A SPECIFIC SONG IN A PARTICULAR MEMORY POSITION, SIMPLY SAVE A NEW SONG
TO THE SAME MEMORY POSITION.
- TO CLEAR (CANCEL) THE ENTIRE PROGRAM WHICH IS STORED IN THE MEMORY, SIMPLY OPEN
THE CD DOOR.
WHAT IS MP3?
- MP3 (MPEG 2, LAYER 3) IS A DIGITAL FILE FORMAT FOR AUDIO (MUSIC).
- YOU CAN DOWNLOAD MP3 SONGS FROM MANY WEBSITES ON THE INTERNET (PLEASE OBSERVE
THE COPYRIGHT REGULATIONS OF YOUR COUNTRY).
- MP3 SONGS ARE MUCH SMALLER IS MEMORY SIZE COMPARED WITH NORMAL CD-AUDIO FORMAT
SONGS. THIS IS CALLED “COMPRESSION” & IT ALLOWS MUCH MORE RECORDING TIME ON
A STANDARD CD THAN THE NORMAL74 MINUTES (FOR NORMAL CD-AUDIO).
- THE EXACT LENGTH OF RECORDING TIME DEPENDS ON THE “COMPRESSION RATE” OF THE MP3
SONG YOU HAVE DOWNLOADED.
- COMPRESSION RATE IS SPECIFIED IN “KBPS” (KILOBITS PER SECOND). FOR EXAMPLE :
“128 KBPS”: THE HIGHER THIS NUMBER, THE BIGGER THE MP3 FILE SIZE (THE BETTER THE
SOUND QUALITY) AND THE LOWER THE RECORDING TIME ON A CD-R. NORMALLY BASED ON
128 KBPS, YOU SHOULD HAVE APPROX. 250-300 MINUTES OF RECORDING TIME ON A CD-R.
- MP3 SONGS CAN BE RECORDED ALONG WITH SOME “TEXT INFORMATION” IN THE SAME FILE.
IT CONSISTS OF (AMONG OTHER DETAILS:)
- FILE NAME (SONG NAME)
- ARTIST NAME
- YOUR CD-MP3 PLAYER CAN STORE (“FIND”) SONGS ON AN MP3-CD DISC SORTING BY THE
"FILE NAME", THEREFORE YOU SHOULD TRY NAMING ALL YOUR MP3 FILES WITH THE ACTUAL
NAME OF THE SONG THAT IT CONTAINS.
E-11
- THERE ARE BASICALLY 2 WAYS TO CREATE AN MP3-CD WITH YOUR FAVORITE
SONGS :
- DOWNLOAD MP3 SONGS FROM INTERNET & BURN THEM ON A CD-R DISC FROM YOUR
COMPUTER.
- CONVERT CD-AUDIO FILES (FROM A NORMAL MUSIC CD) ONTO INTO MP3 FORMAT
FROM YOUR COMPUTER, USING A KIND SOFTWARE CALLED “CD-RIPPER”.
(WHICH IS FREEWARE/SHAREWARE ON INTERNET).
HOW TO PLAY CD-MP3 DISCS
- PRESS "ON/OFF" KEY TO SWITCH ON THE UNIT.
- INSERT AN MP3 CD INTO THE CD PLAYER AND CLOSE THE CD DOOR.
- PRESS PLAY .
- THE DISC WILL SPIN AND THEN PLAYBACK THE FIRST SONG (TRACK), THE DISPLAY WILL INDICATE
THE CURRENT TRACK NO. (“001” IF IT IS THE FIRST TRACK) AS WELL AS THE PLAY TIME OF THAT
TRACK IN MINUTES AND SECONDS.
- AT ANYTIME DURING PLAYBACK, PRESS PLAY KEY TO PAUSE AND PRESS PLAY KEY TO RESUME
OPERATION AT THE SAME TRACK & POSITION.
- AT ANYTIME DURING PLAYBACK, PRESS AND RELEASE NEXT OR BACK TO SKIP FORWARDS OR
BACKWARDS BY ONE TRACK.
- AT ANYTIME DURING PLAYBACK, PRESS AND HOLD NEXT OR BACK TO REVIEW (FAST REWIND)
OR CUE (FAST FORWARDS) THE CURRENT TRACK.
- AT ANYTIME DURING PLAYBACK, PRESS AND HOLD FIND KEY FOR 1 SECOND.
THE DISPLAY WILL SHOW THE FILE NAME (SONG NAME) INFORMATION.
USB-DRIVE & SD-CARD MP3 PLAYBACK
- THIS UNIT IS EQUIPPED WITH A USB SOCKET WHICH ACCEPT AND PLAY MP3
FILES
STORED ON STANDARD
USB FLASH DRIVES (ALSO KNOWN AS "PEN DRIVES")
3D-VIRTUAL
SURROUND
WHICH ARE FOR MEMORY STORAGE. (COMPATIBLE WITH USB VERSION 1.1 & 2.0).
- THIS UNIT ALSO HAS A BUILT-IN SD-CARD SOCKET WHICH ACCEPT AND PLAY
MP3 FILES STORED ON STANDARD "SD" TYPE FLASH MEMORY CARDS
(OF MAXIMUM CAPACITY = 1 GB) WHICH ARE COMMONLY AVAILABLE.
- TO UTILIZE THIS FACILITY, FIRST INSERT EITHER A USB-DRIVE OR A SD-CARD INTO
THE CORRECT SLOT (PORT) ON THE FRONT OF THE UNIT AS SHOWN BELOW:
USB-DRIVE
SD-CARD
- PRESS USB/SD .
- AFTER ABOUT 5-10 SECONDS THE DISPLAY WILL INDICATE THE NUMBER OF MP3
SONGS FOUND ON THE USB-DRIVE OR SD-CARD, AND ALSO THE NUMBER OF
FOLDERS ON THE DEVICE.
NUMBER OF MP3
SONGS ON
THE DEVICE
09
STOP
073
VOLUME
E-12
NUMBER OF
THE FOLDERS (ALBUM)
ON THE DEVICE
- PRESS THE FOLDER KEY REPEATEDLY TO SELECT THE DESIRED FOLDER NUMBER.
- PRESS NEXT OR BACK TO SKIP FORWARD OR BACKWARDS TO SELECT THE
DESIRED MP3 FILE IN THE SELECTED FOLDER.
- PRESS PLAY TO START PLAY BACK OF THE SELECTED SONG.
- ALL FUNCTIONS FOR USB-DRIVE & SD-CARD MP3 PLAYBACK ARE EXACTLY THE SAME AS IN
CD-MP3 MODE (AS PREVIOUSLY DESCRIBED).
- IF A USB-DRIVE & A SD-CARD ARE SIMULTANEOUSLY INSERTED INTO BOTH SLOTS, THE UNIT WILL
AUTOMATICALLY READ THE USB-DRIVE FIRST AND ALLOW PLAYBACK OF THE CONTENTS OF THE
USB-DRIVE AS USUAL. IN SUCH A CASE, TO SELECT THE SD-CARD, PRESS USB/ SD ONCE TO
SWITCH FROM SD-CARD TO USB-DRIVE.
- TO SWITCH BACK TO SD-CARD, SIMPLY PRESS USB/ SD AGAIN.
NOTE:
ALTHOUGH THIS PRODUCT IS FULLY COMPATIBLE WITH USB 1.1 & 2.0 STANDARDS, A SMALL
PERCENTAGE (ABOUT 5%) OF USB FLASH DRIVES MIGHT NOT BE READABLE, DUE TO THOSE
USB-DRIVE MANUFACTURERS NON-COMPLIANCE WITH THE FULL (OFFICIAL) USB 1.1 / 2.0 STANDARDS.
IMPORTANT:
THIS UNIT DOES NOT SUPPORT USB-MP3 PLAYER, DUE TO THEIR INHERENT LACK OF SOFTWARE
COMPATIBILITY.
ONLY USB "PEN DRIVES" (FLASH MEMORY USB DRIVES) CAN BE USED, FOR MP3 PLAYBACK.
THE READING TIME FOR A USB-DRIVE OR SD-CARD VARIES DEPENDING ON THE SPEED OF THE
MEMORY DEVICE AND THE NUMBER OF SONGS AND FOLDERS. IN SOME CASES THE READING
TIME MAY BE AS LONG AS 60 SECONDS.
IMPORTANT
ALWAYS SWITCH OFF THE UNIT OR CHANGE MODE TO “CD” OR “RADIO”BEFORE REMOVING A USB
FLASH DRIVE OR SD-CARD, TO PREVENT DAMAGE TO YOUR USB DEVICE OR MEMORY CARD.
ENCODING FUNCTION (RECORDING TO MP3 FILE)
ENCODING FUNCTION IS THE MOST INTELLIGENT FUNCTION WHICH ALLOWS DIFFERENT AUDIO
SOURCES TO BE RECORDED AND/OR TRANSFER INTO THE USB OR SD-CARD AS A MP3 FORMAT FILE.
AT ANYTIME DURING CD/ CD-MP3 PLAYBACK, CASSETTE TAPE PLAYBACK OR AUX-IN FUNCTION,
THIS FUNCTION IS ABLE TO RECORD AND/OR TRANSFER THE DESIRED TRACK OR SOUND CLIP
INTO THE USB OR SD-CARD, AS FOLLOWS:
ENCODING FROM CD/ CD-MP3:
- SWITCH TO CD MODE, OPEN THE CD DOOR AND INSERT A CD/ CD-MP3 DISC AS USUAL.
- INSERT A USB / SD CARD INTO THE USB/ SD CARD SLOT.
- SELECT A TRACK THAT IS DESIRED TO BE TRANSFERRED AND RECORDED, THEN START PLAYING
THE TRACK BY PRESSING PLAY .
- AT ANYTIME DURING PLAYBACK, PRESS REC . THE TRACK WILL THEN BE REFRESHED AND START
PLAYING AGAIN FROM THE BEGINNING, AND “REC” WILL ALSO BE SHOWN ON THE DISPLAY TO
INDICATE THAT THE CD IS BEING RECORDED.
- THE RECORDING WILL CONTINUE AND AUTOMATICALLY STOP AT THE END OF THE CD.
IT WILL ALSO SAVE EACH TRACK(SONG) INTO A NEW FILE WITH A UNIQUE NAME AUTOMATICALLY
(IE. TMCDA001, TMCDA002... OR COPY THE ORIGINAL FILE NAME FROM THE CD-MP3 DISC). THESE
FILES WILL BE LOCATED ON THE USB/ SD CARD UNDER THE FOLDER NAME CALLED “TMCDA001”.
- TO STOP RECORDING BEFORE THE END OF THE SONG, SIMPLY PRESS REC OR STOP AT ANY
TIME. THIS WILL CREATE AN MP3 FILE OF THE PARTIAL SONG. ONCE RECORDING HAS STOPPED,
THE “REC” SYMBOL WILL NO LONGER BE DISPLAYED.
ENCODING FROM CASSETTE TAPE:
- SWITCH TO TAPE MODE, OPEN THE CASSETTE DOOR AND INSERT A TAPE AS USUAL.
- INSERT AN USB / SD CARD INTO THE USB/ SD CARD SLOT.
- ADJUST THE TAPE (REWIND OR FAST FORWARD) UNTIL REACHING THE DESIRED
POSITION ON THE TAPE. PRESS PLAY TO START PLAYBACK OF THE TAPE.
- AT ANYTIME DURING PLAYBACK PRESS REC , “REC” WILL BE SHOWN ON THE DISPLAY
TO INDICATE THAT THE CASSETTE-AUDIO IS BEING RECORDED.
- TO STOP RECORDING, SIMPLY PRESS REC AGAIN OR STOP . THE “REC” SYMBOL WILL
NO LONGER BE DISPLAYED.
ENCODING FROM RADIO
- SWITCH TO RADIO MODE.
- SELECT A RADIO CHANNEL THAT IS DESIRED TO BE RECORDED.
- PRESS REC AT ANYTIME, "REC" WILL SHOWN ON THE DISPLAY TO INDICATE THAT THE MACHINE
IS RECORDING.
- TO STOP RECORDING, SIMPLE PRESS REC AGAIN OR STOP ONCE RECORDING HAS STOPPED.
THE "REC" SYMBOL WILL NO LONGER BE DISPLAYED.
IMPORTANT
IF A RADIO STATION IS WEAK AND UNCLEAR, THEN ENCODING IT TO MP3 WILL NOT YIELD GOOD
RESULTS, WHICH IS NORMAL. THE ENCODING FUNCTION NEEDS A GOOD (STRONG) RADIO SIGNAL
TO WORK PROPERLY.
E-13
ENCODING FROM AUX-IN:
- SWITCH TO AUX-IN MODE, PLUG IN AND TURN ON THE EXTERNAL DEVICE.
- INSERT AN USB / SD CARD INTO THE USB/ SD CARD SLOT.
- START PLAYBACK OF THE EXTERNAL DEVICE AND ENSURE THAT IT’S AUDIO SIGNAL IS BEING
HEARD THOUGHT THIS UNIT.
- AT ANYTIME PRESS REC , “REC” WILL BE SHOWN ON THE DISPLAY TO INDICATE THAT THE
AUX-IN AUDIO IS BEING RECORDED.
- TO STOP RECORDING, SIMPLY PRESS REC AGAIN OR STOP . ONCE RECORDING HAS STOPPED,
THE “REC” SYMBOL WILL NO LONGER BE DISPLAYED.
- NOW, THE DESIRED SOUND TRACK HAS BEEN SAVED INTO A NEW FOLDER IN THE USB/SD-CARD
AS MENTIONED ABOVE. TO PLAY THE RECORDED MP3-FILES ON THE USB/SD CARD,
PLEASE FOLLOW THE INSTRUCTION ON PAGE E-13 FOR USB-DRIVE & SD-CARD MP3 PLAYBACK.
- IF A USB-DRIVE AND AN SD-CARD ARE SIMULTANEOUSLY INSERTED INTO BOTH SLOTS,
THE UNIT WILL QUESTION IF THIS RECORD COMMAND IS TO SAVE THE MP3 FILE TO THE USB OR
THE SD-CARD.
- IN SUCH A CASE, AFTER PRESSING REC , “REC USB” WILL BE SHOWN ON THE DISPLAY FIRST.
THE NEXT BUTTON IS USED IN THIS CASE TO SELECT THE RECORDING DESTINATION.
SIMPLY PRESS NEXT , “REC CARD” WILL SOON BE DISPLAYED. IF PRESSING NEXT AGAIN THE
SELECTION LIST WILL BE ROTATED AND “REC USB” WILL BE DISPLAYED AGAIN.
- TO CONFIRM THE SELECTION, SIMPLY PRESS REC AND THE MP3 FILE WILL BE SAVED INTO THE
COMMANDED DESTINATION.
NOTE: PLEASE MAKE SURE THAT THE USB DRIVE / SD CARD HAS ENOUGH FREE
MEMORY SPACE FOR THE INCOMING MP3 FILE, OTHERWISE “FULL” WILL BE
DISPLAYED AND RECORDING WILL NOT START.
RECORDING QUALITY
THERE ARE THREE LEVELS OF QUALITY THAT CAN BE SELECTED FOR RECORDING
MP3 TO A USB OR AN SD-CARD:
BPS (BITS PER SECOND)
MP3 ENCODING
QUALITY SETTING
CD
TAPE / RADIO / AUX-IN
HIGH
256K
128K
MID
128K
96K
LOW
64K
64K
- AT ANY MODE WHEN READY TO START RECORDING, PRESS AND HOLD REC FOR 2 SECONDS,
NOTICE THAT “REC - LOW” WILL APPEAR ON DISPLAY. SIMPLY PRESS REC REPETITIVELY TO
SELECT ONE OF THE QUALITY LEVELS FROM “REC - LOW”, “REC-MID” AND “REC - HIGH”.
THEN RELEASE THE BUTTON WHEN A DESIRED QUALITY LEVEL IS SELECTED, AND THE AUDIO
WILL THEN BE RECORDED WITH THE REQUIRED QUALITY LEVEL.
NOTE: THE COMMAND WILL STILL BE REMAINED FOR ANY UP COMING RECORDING
UNTIL AN AMENDMENT IS MADE.
DELETING A FILE FROM USB / SD CARD
- PRESS USB/SD TO SELECT USB OR SD CARD.
- PRESS AND HOLD REC FOR 3 SECONDS UNTIL “DELETE” IS DISPLAYED.
- PRESS NEXT REPETITIVELY TO SELECT THE FOLDER WHERE THE UNWANTED MP3 FILE IS
LOCATED.
- PRESS AND HOLD NEXT FOR 1 SECOND TO OPEN UP THE SELECTED FOLDER BY THE FOLDER
NAME.
- IN THE SELECTED FOLDER, PRESS NEXT ONCE TO SELECT THE UNWANTED MP3 FILE BY THE
FILE NAME.
- PRESS AND HOLD REC UNTIL “DELETE” IS DISPLAYED, THEN THE FILE IS SUCCESSFULLY
DELETED.
- TO CANCEL DELETING, PRESS STOP AT ANY TIME DURING ANY PREVIOUS STEPS.
NOTE: THIS DELETE FUNCTION CAN ONLY DELETE ANY SELECTED FILES BUT NOT
THE FOLDER. WHEN ALL FILES IN A PARTICULAR FOLDER HAD BEEN DELETED, THE
EMPTY FOLDER WILL STILL REMAIN IN THE USB-DRIVE OR SD CARD.
E-14
TEXT DISPLAY MODE (id3 display)
- THIS UNIT IS CAPABLE OF DISPLAYING THE "TEXT INFORMATION" (id3 TAG) OF AN MP3 SONG ON
THE LCD DISPLAY.
- TO SWITCH ON THIS FUNCTION, SIMPLY PRESS & HOLD THE FIND
KEY FOR 1 SECONDS.
- TO SWITCH BACK TO NORMAL DISPLAY MODE (TO DISPLAY TRACK NUMBER, etc.), PRESS & HOLD
THE FIND KEY AGAIN FOR 1 SECONDS.
FINDING (SEARCHING) MP3 SONGS BY SONG NAME (FOR CD-MP3 ONLY)
- AT STOP OR PLAY MODES, PRESS FIND KEY ONCE.
- THE “FIND” SYMBOL WILL “FLASH” IN THE DISPLAY, AND THE LETTER “A” WILL BE
SHOWN.
THIS IS THE “SEARCH ALPHABET”.
- PRESS NEXT OR BACK KEYS TO ADVANCE THE
“SEARCH ALPHABET” (A B C D...) TO SELECT THE DESIRED SEARCH ALPHABET.
- AT EVERY SELECTED “SEARCH ALPHABET” THE LOWER PART OF THE DISPLAY
WILL SHOW THE NAME OF THE FIRST SONG BEGINNING WITH THAT SELECTED
ALPHABET, ON THE DISC.
EXAMPLE:
AT "STOP" OR "PLAY"
MODE PRESS ONCE
FIND
FIND SYMBOL
SEARCH
ALPHABET
NAME OF SONG
(MP3 FILE)
A -- APPLE . . . . .
PRESS ONCE
NEXT
FIND SYMBOL
SEARCH
ALPHABET
B -- BANANA . . .
NAME OF SONG
(MP3 FILE)
PRESS ONCE
NEXT
ETC...
- WITH ANY SELECTED ALPHABET, THERE MIGHT BE SEVERAL SONGS ON THE DISC (WHICH BEGIN
WITH THE SAME ALPHABET). TO SEARCH FOR ALL SONGS BEGINNING WITH A PARTICULAR
ALPHABET, PRESS AND “HOLD” THE NEXT OR BACK KEYS (FOR 2 SECONDS) UNTIL THE
“FIND” STOPS FLASHING IN THE DISPLAY.
- ONCE THE "FIND" SYMBOL STOPS FLASHING, PRESS THE NEXT KEY TO DISPLAY THE NEXT SONG
STARTING WITH SAME ALPHABET. REPEAT UNTIL DESIRED SONG IS LOCATED.
- AT ANYTIME, WHEN YOU HAVE LOCATED A DESIRED SONG (AS SHOWN ON SCREEN)
JUST PRESS “PLAY”
TO LISTEN TO IT.
- TO EXIT THE “FIND” MODE PRESS THE FIND KEY TWICE UNTIL THE “FIND”
SYMBOL DISAPPEARS FROM THE DISPLAY.
E-15
FINDING (SEARCHING) MP3 SONGS BY ALBUM (FOLDER)
(FOR CD-MP3, USB-DRIVE & SD-CARD)
- MP3 FILES (SONGS) CAN BE ORGANIZED INTO FOLDERS (DIRECTORIES) WHEN YOU RECORD
THEM ON TO A CD-R DISC. EACH FOLDER IS CALLED AN "ALBUM" AND YOU CAN (FOR EXAMPLE)
ORGANIZE YOUR ALBUMS ON A DISC SO THAT EACH ALBUM CONTAINS SONGS BY A PARTICULAR
ARTIST, OR ALTERNATIVELY, BY A DIFFERENT GENRE OR TYPE. YOU CAN ORGANIZE SONGS &
ALBUMS IN ANY WAY YOU WISH SO THAT YOU CAN LOCATE & PLAY BACK THOSE SONGS WITH
GREATER EASE & CONVENIENCE.
- TO SEARCH FOR SONGS WITHIN A PARTICULAR ALBUM:
- FOR USB-DRIVE & SD-CARD: PRESS THE FIND KEY ONCE
- FOR CD-MP3: PRESS THE FIND KEY TWICE
- THE "FIND" & "ALBUM" SYMBOLS WILL ACTIVATE IN THE DISPLAY, TOGETHER WITH THE NUMBER
"1". THIS IS THE "ALBUM NUMBER" (IT INDICATES THE NUMBER OF THE FOLDER ON THE DISC).
- PRESS NEXT or BACK TO ADVANCE THE ALBUM NUMBER
(01 02 03 ...). THE NAME OF EACH ALBUM (THE DIRECTORY NAME) WILL
APPEAR IN THE LOWER PART OF THE DISPLAY FOR EACH SELECTED ALBUM NUMBER.
EXAMPLE:
FIND ALBUM
01
ALBUM
ALBUM
NUMBER
FRUITS . . . . . . . .
NAME OF ALBUM
PRESS ONCE
NEXT
FIND ALBUM
02
ALBUM
ALBUM
NUMBER
VEGETABLES. . . . ..
NAME OF ALBUM
PRESS ONCE
NEXT
ETC ...
- WHEN THE DESIRED ALBUM NAME APPEARS ON SCREEN, "PRESS & HOLD" THE NEXT KEY
(FOR 2 SECONDS) UNTIL THE "ALBUM"SYMBOL DISAPPEARS. THIS WILL OPEN THE SELECTED
ALBUM & ALLOWS YOU TO DISPLAY ALL THE SONGS CONTAINED INSIDE THAT ALBUM SO THAT
YOU CAN SELECT THE DESIRED SONG BY USING THE NEXT KEY & PLAY IT BY USING
THE
"PLAY" KEY.
E-16
PRESS & HOLD FOR 2 SECS. !
NEXT
ALBUM NAME
(WHICH YOU
WANT TO OPEN)
02
ALBUM
THIS WILL
DISAPPEAR AFTER
2 SECONDS
ALBUM
NUMBER
VEGETABLES. . . . ..
01
NAME OF 1st SONG IN
THE SELECTED ALBUM
CARROT... . . . ..
NEXT
SONG NUMBER
(WITHIN THIS SELECTED
ALBUM)
PRESS & RELEASE REPEATEDLY
TO SCROLL THROUGH ALL SONGS
CONTAINED INSIDE THE SELECTED ALBUM
01
NAME OF DESIRED SONG IN
THE SELECTED ALBUM
TOMATO... . . . ..
PRESS THE "PLAY" KEY TO PLAY
THE SONG DISPLAYED.
- TO EXIT THE "FIND" MODE PRESS THE FIND KEY ONCE UNTIL THE "FIND" SYMBOL
DISAPPEARS FROM THE DISPLAY.
E-17
REPEAT PLAYBACK FUNCTION
- AT ANYTIME DURING PLAYBACK:
- 3D-VIRTUAL
PRESS REPEAT SURROUND
REPEATEDLY TO SELECT
= TO REPEAT THE CURRENT TRACK
REPEAT 1
= TO REPEAT ALL TRACK (FULL CD)
REPEAT ALL
REPEAT ALBUM = TO REPEAT ALL SONGS FROM CURRENTLY SELECTED
ALBUM(DIRECTORY)
ANTI-SKIP (ANTISHOCK) FUNCTION [ESP]
- THIS UNIT HAS A BUILT-IN DIGITAL ANTI-SKIP FUNCTION WHICH PREVENTS CD "SKIPPING" WHEN
THE UNIT IS PHYSICALLY MOVED OR SUBJECTED TO VIBRATIONS FOR UP TO 25 SECONDS WHEN
PLAYING CD-MP3 DISCS. PLEASE NOTE THERE IS NO ANTI-SHIP FUNCTION FOR NORMAL
AUDIO-CD PLAYBACK. (ONLY FOR CD-MP3).
- WHENEVER ANY CD-MP3 DISC IS PLAYED , DURING THE FIRST 20 (APPROX.) SECONDS THE
ANTI-SKIP MEMORY IS BEING FILLED UP (BUT IS NOT YET FULL). THE ANTI-SHOCK PROTECTION
IS ALREADY ACTIVE (IN USE) AT THIS TIME, BUT IS NOT YET UP TO THE MAXIMUM 25 SECONDS
CAPACITY.
- ONCE THE ANTI-SHCOK MEMORY IS FULL, THE UNIT PROVIDES ANTI-SKIP PROTECTION FOR
25 SECONDS OF VIBRATION.
- PLEASE NOTE THAT THE ANTI-SKIP FUNCTION ONLY PROTECTS AGAINST NORMAL VIBRATION
OR MINOR MOVEMENT. SEVERE OR STRONG SHOCKS/ VIBRATIONS TO THE UNIT MAY STILL
CAUSE SKIPPING.
USING THE AUDIO LINE IN CONNECTION (AUX-INPUT)
- YOU CAN CONNECT THE AUDIO OUTPUT OF AN EXTERNAL DEVICE SUCH AS A MP3
PLAYER TO THIS UNIT, TO LISTEN TO THE SOUND OF THAT DEVICE THROUGH THE
HIGH QUALITY AMPLIFIER OF THIS MUSIC SYSTEM.
- TO CONNECT THE EXTERNAL DEVICE PLEASE USE A STANDARD RCA CABLE TO
CONNECT THE "AUDIO LINE-OUT" OF THE DEVICE (LEFT AND RIGHT CHANNELS)
TO THE "AUX LINE-IN" RCA JACKS (LEFT & RIGHT) ON THE REAR PANEL OF THIS UNIT.
- SWITCH TO FUNCTION "AUX" BY PRESSING AUX KEY.
- MAKE SURE THAT THE SPEAKERS ARE CONNECTED TO THE MAIN UNIT.
- SWITCH ON THE POWER OF THE MAIN UNIT AND THE EXTERNAL DEVICE (eg. MP3PLAYER).
- START PLAYBACK OF THE EXTERNAL DEVICE AND ADJUST THE VOLUME CONTROL
OF THE MAIN UNIT TO THE DESIRED LEVEL.
- REMEMBER TO SWITCH OFF THE POWER OF THE MUSIC SYSTEM (MAIN UNIT)
WHEN YOU ARE FINISHED USING THE EXTERNAL DEVICE.
CONNECTING AN EXTERNAL POWERED SUBWOOFER (NOT INCLUDED)
- THIS UNIT HAS A BUILT IN SUBWOOFER CONNECTION WHICH CAN BE CONNECTED TO ANY
STANDARD POWERED SUBWOOFER.
- BY CONNECTING TO A POWERED SUBWOOFER, THE LOW FREQUENCY(BASS SOUND) CAN BE
STRONGLY ENHANCED TO PROVICE A MUCH RICHER AND DEEPER SOUND TO YOUR MUSIC.
- TO USE THIS FACILITY, SIMPLY CONNECT ANY STANDARD POWERED SUBWOOFER
(EASILY AVAILABLE FROM MOST MUSIC EQUIPMENT SHOPS) USING THE RCA JACK ON THE
REAR PANEL OF THE MAIN UNIT.
- SWITCH ON THE POWERED SUBWOOFER.
- PLAY ANY MUSIC SOURCE (CD or RADIO or AUX) AS USUAL.
- YOU WILL IMMEDIATELY NOTICE THE DEEPER SOUND, WHICH CAN BE FURTHER ENHANCED BY
SWITCHING ON THE "SUPER BASS" FUNCTION ON THE MAIN UNIT.
- PLEASE NOTE THAT THE SPEAKERS SHOULD BE CONNECTED AS USUAL TO THE MAIN UNIT,
WHEN USING A SUBWOOFER.
- PLEASE NOTE THAT "PASSIVE" (NON-POWERED) SUBWOOFERS WILL NOT WORK WITH THIS UNIT.
E-18
SYSTEM SET UP PROCEDURE
A. AS A "SHELF SYSTEM" (TABLE TOP USE)
- INCLUDED 1 PC STAND FOR THE MAIN UNIT.
- INCLUDED 2 PCS STAND FOR THE SPEAKERS.
FIXING THE BASE TO THE MAIN UNIT OR SPEAKERS:
1. PLACE THE STAND UNDER
THE MAIN UNIT OR SPEAKERS
2. SLIDE THE STAND UPWARD
(SEE DIAGRAM BELOW).
3. STOP WHEN THE INDICATOR MARK ON THE STAND IS ALIGNED WITH THE LOCK SYMBOL
ON THE REAR CABINET.
(TO RELEASE THE STAND FROM THE MAIN UNIT OR SPEAKERS, SLIDE THE
STAND DOWNWARDS (OPPOSITE DIRECTION) UNTIL IT BECOMES
RELEASED.
INDICATOR MARK
LOCKED
CLICK
LOCK SYMBOL
WHEN THE INDICATOR MARK ON THE STAND
IS ALIGNED WITH THE LOCK SYMBOL ,
THE BASE IS PROPERLY IS PROPERLY INSTALLED.
E-20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising